Philips | Exprelia Evo Class | Operating instructions | Philips Saeco Exprelia Evo Class

Register your product and get support at
02
English
www.philips.com/welcome
Type HD8857
02
EN
OPERATING INSTRUCTIONS
READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. Save these instructions.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use only. Any servicing, other than cleaning and
user maintenance, should be performed by an authorized service center. Do not
immerse machine in water. To reduce the risk of fire or electric shock, do not
disassemble the machine. There are no parts inside the machine serviceable by
the user. Repair should be done by authorized service personnel only.
1. Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during
operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available
and may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.
VI
CARAFE ASSEMBLY PROCEDURE
For correct use of the carafe, refer to the instructions on page 12.
A
The maintenance instructions for the carafe circuits are described on page 36.
The disassembly and cleaning instructions for the components are described on page 41.
1
2
3
4
5
6
C
A
D
B
7
B
8
E
THOROUGHLY CLEAN THE CARAFE AT FIRST USE AND AFTER A LONG PERIOD OF INACTIVITY.
A THOROUGH SANITATION AND CLEANING OF THE CARAFE ENSURES CORRECT OPERATION AND PREVENTS THE
PROLIFERATION OF BACTERIAL LOADS WHICH MAY BE HARMFUL FOR HUMAN HEALTH.
INDEX
1
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MACHINE COMPONENTS & ACCESSORIES - CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
STARTING THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SETTING THE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
MEASURING THE WATER HARDNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FIRST USE - USE AFTER A PERIOD OF INACTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
INTENZA WATER FILTER (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
COFFEE STRENGTH (SAECO BREWING SYSTEM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPTI-DOSE (ADJUSTS THE AMOUNT OF COFFEE TO GRIND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SAECO ADAPTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
COFFEE GRINDER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DISPENSING SPOUT HEIGHT ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
STAND-BY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
SCREEN SAVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MILK CARAFE USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
COFFEE BREWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ESPRESSO / COFFEE / LONG COFFEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
BEVERAGE BREWING WITH PRE-GROUND COFFEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CAPPUCCINO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LATTE MACCHIATO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CLEANING CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-19
SPECIAL BEVERAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
"SPECIAL" BUTTON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
HOT MILK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
HOT WATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
STEAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
BEVERAGE LENGTH QUICK PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
BEVERAGE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MACHINE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
MAINTENANCE DURING OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
GENERAL MACHINE CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
BREW GROUP CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
MILK CARAFE CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
MILK CARAFE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
MACHINE WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2
GENERAL INFORMATION - TECHNICAL DATA
GENERAL INFORMATION
HOW TO USE THESE INSTRUCTIONS
This coffee machine is suitable for preparing espresso
coffee using coffee beans and is equipped with a device to
dispense steam and hot water.
The machine is designed for domestic use and not suitable
for heavy or professional use.
Keep these operating instructions in a safe place and make them
available to anyone else who would use the coffee machine. For
further information or in case of problems, please refer to the an
authorized service center. For Saeco customer service, call (800)
933-7876 in the U.S. or (514) 385-5551 in Canada.
Warning: No liability is held for damage caused by:
• Incorrect use not in accordance with the intended purposes.
• Repairs not carried out by authorized service centers.
• Tampering with the power cord.
• Tampering with any parts of the machine.
• Use of non-original spare parts and accessories.
• Failure to descale the machine or machine use at temperatures
below 32°F (0°C).
SAVE THESE INSTRUCTIONS
IN THESE CASES, THE WARRANTY SHALL BE DEEMED NULL
AND VOID.
THE WARNING TRIANGLE INDICATES ALL
IMPORTANT INSTRUCTIONS FOR THE USER'S
SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS
CAREFULLY TO PREVENT SERIOUS INJURIES.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
• A short power-supply cord is provided to reduce risks resulting
from becoming entangled in or tripping over a longer cord.
• Extension cords may be used if care is exercised in their use.
If an extension cord is used, make sure:
a. The marker electrical rating of the extension cord
should be at least as great as the electrical rating of the
appliance.
b. The extension cord should be arranged so that it will not
drape over the counter top or table top where it can be
pulled on by children or tripped over.
c. If the appliance is of the grounded type, the extension
cord should be a grounding-type 3-wire cord.
• Do not use multi-sockets
TECHNICAL DATA
Nominal voltage
Power rating
Power supply
Shell material
Size (w x h x d)
Weight
Cord length
Control panel
Water tank
Coffee bean hopper capacity
Pump pressure
Boiler
Coffee grinder
Quantity of ground coffee
Dregdrawer capacity
Safety devices
See label on the appliance
See label on the appliance
See label on the appliance
Thermoplastic material/Metal
245 x 360 x 420 mm
14.2 Kg
1200 mm
Front
1.5 liters - (removable)
300 grams
15 bar
Stainless steel
Ceramic
7 - 10,5 g
about 11
Boiler pressure safety valve – Double safety thermostat.
MACHINE COMPONENTS AND ACCESSORIES - CONTROL PANEL
3
The references of this table are reported in the attached carton paper, in which the components are illustrated.
COMPONENTI APPARECCHIO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Water tank + cover
Pre-ground bypass doser
Service door
SBS dial
Hot water/steam wand
Full drip tray indicator
Coffee bean hopper with lid
Grinder adjustment
Control panel
Milk container couplings
Dispensing spout
Drip tray + grill + sealed support
Brew group
Used grounds drawer + protection element
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Liquid recovery tray + cover
Service door button
Power button
Power cord connector
Milk carafe
Pre-ground coffee measuring scoop
Water hardness test strip
Brew group lubricant
Descaling solution - (Optional)
Brew group cleaning tablets - (Optional)
Power cord
Intenza water filter - (Optional)
Cleaning brush
Carafe coupling cap
CONTROL PANEL
The control panel has been designed to allow an ergonomic use of all machine functions.
Latte Macchiato brew button
Espresso button
Cappuccino button
Coffee button
Function buttons
Function buttons
Special beverage button
Long Coffee button
Aroma / pre-ground
coffee selection button
"MENU" button
Carafe cleaning cycle activation
button (Clean)
Stand-by button
4
INSTALLATION
STARTING THE MACHINE
Before turning on the machine, make sure that the power button is set to "0".
1
2
Lift the right outer lid and remove the
inner lid.
4
Slowly pour coffee beans into the
hopper.
Replace the inner lid and close the outer
lid.
5
Remove the water tank using the handle.
7
Fill the tank with fresh drinking water. Do
not exceed the "max" level indicated on
the water tank. Place the water tank back
into the machine.
3
Lift the left outer lid and remove the
inner lid.
6
Insert the plug into the socket located
on the back of the machine and insert
the other end into a power outlet with
suitable current.
8
Press the power button to the "I"
position to turn the machine on.
The frame of the " " button on the
display blinks red.
Press any button to start the machine.
When the correct temperature is
reached, the machine performs a
priming and rinsing cycle of the
internal circuits. A small amount of
water is dispensed. Wait for this cycle
to be completed.
The screen for product dispensing
appears on the display; see page 3.
At first start-up only, the screen (1) will be displayed as shown on page 5.
Then, the language can be set from the relevant menu only (see page 27).
5
SETTING THE LANGUAGE
This setting allows you to choose the operating language of the machine. It also allows you to adjust the parameters of the beverages to
the typical parameters of the country where the machine is used. This is why some languages are differentiated also by country.
If no language is selected, you will be requested to select it the next time the machine is started.
1
2
3
LANGUAGE
LANGUAGE
ITALIANO
ENGLISH
DEUTSCH
ITALIANO
ENGLISH
DEUTSCH
Select the desired language by pressing
the arrow buttons ( ) or ( ).
4
HEATING UP…
Press the save button.
The machine activates the warming up
phase. Wait until it is completed.
5
6
RINSING
STOP
When warm-up phase is complete, the
machine performs a rinsing cycle of the
internal circuits. It is possible to interrupt
the cycle by pressing the "STOP" button.
A small quantity of water is dispensed.
Wait for this cycle to be completed
automatically.
The machine is now ready for use.
MEASURING THE WATER HARDNESS
The test strip can only be used for one measurement.
1
2
A
1
Immerse the water hardness test strip
provided with the machine in water for
1 second.
Intenza Aroma System
B
2
3
4
Machine water hardness setting
Wait a minute, then check the water hardness value and set:
- The machine water hardness level (page 30).
- The Intenza Aroma System (page 7).
C
6
INSTALLATION
FIRST USE - USE AFTER A PERIOD OF INACTIVITY
To improve the product quality, carry out this procedure at first use of the machine and after long periods of inactivity.
A few simple operations are needed to ensure the quality of your favourite beverages over time.
1
2
Place a container of large size under the
coffee dispensing spout.
3
Press the button once or more until the
icon is displayed.
5
4
OK
Select the product by pressing the
button shown.
6
SPECIAL BEVERAGES
INSERT
GROUND COFFEE
AND PRESS OK
HOT MILK
HOT WATER
STEAM
ESC
Press the "OK" button to start dispensing
water through the dispensing spout. DO
NOT insert coffee at this stage.
7
At the end of the dispensing phase,
remove the container and place it under
the hot water wand.
Press the "SPECIAL" button.
8
Select "HOT WATER" by pressing button
( ) or( ). Press the "OK"' button and
wait for the programmed quantity to be
dispensed.
9
HOT W
5
STOP
Dispensing can be interrupted by
pressing the "STOP" button.
At the end, remove the container and
empty it.
7
Repeat the process from step 5 to step 7
until the water tank is empty.
Fill the water tank with fresh drinking
water as previously described. Your
machine is now ready to brew excellent
beverages!
7
INTENZA WATER FILTER - (OPTIONAL)
To improve the quality of the water you use and extend the life of your machine at the same time, it is recommended that you install the
water filter. After installation, go to the water filter initialization programme (see the "MACHINE MENU", page 27). In this way, the machine
informs the user when the water filter must be replaced.
Remove the water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and
gently press its sides to let the air bubbles out.
1
2
Remove the small white filter from the
tank and store it in a dry place sheltered
from dust.
4
3
Set up the Intenza Aroma System:
A = Soft water
B = Medium water (standard)
C = Hard water
5
Insert the filter in the empty tank. The
reference mark and the groove must
match. Push firmly until it is completely
inserted.
6
WATER MENU
ENABLE FILTER
ACTIVATE FILTER
Fill the tank with fresh drinking water up
to the "MAX" level and then place it back
into the machine.
7
Place a large container under the hot
water wand.
8
OK
ACTIVATE FILTER?
9
OK
INSERT FILTER.
FILL THE TANK
ESC
Press the "OK" button.
Access the "MACHINE MENU" (see
page 27). Select "WATER MENU" and
"ACTIVATE FILTER", then press "OK".
Press the "OK" button to confirm the
introduction of the new water filter.
OK
PLACE A CONTAINER
UNDER THE
WATER SPOUT
Press the "OK" button to confirm. Wait
until the cycle is completed and remove
the container.
NOTE: At the end of the procedure the display automatically returns to the product dispensing page.
If the Intenza water filter is not available, insert the small white filter previously removed (see point 1) into the tank.
8
ADJUSTMENTS
COFFEE STRENGTH (SBS)
The SBS dial has been carefully designed to give your coffee the fullness and intensity you desire. Simply turn the dial and set the coffee
from mild intensity to strong intensity, according to your own taste.
SBS – SAECO BREWING SYSTEM
The Saeco Brewing System (SBS) adjusts the fullness of the brewed coffee. The coffee may even be adjusted while brewing.
This adjustment has an immediate effect on the selected type of brewing.
MEDIUM
COFFEE
MILD
COFFEE
STRONG
COFFEE
OPTI-DOSE (ADJUSTS THE AMOUNT OF COFFEE TO GRIND)
The machine allows you to adjust the right quantity of ground coffee for each product. The standard adjustment for each product can be set
in the "BEVERAGE MENU" (see page 24).
You may temporarily change the amount of coffee ground as well. This change applies only to the brewing of the next coffee.
Press the " " button on the control panel to temporarily change the quantity of ground coffee, or select the pre-ground function. If no
products are brewed, 30 seconds after performing the selection the machine returns to the pre-set beverage standard setting.
1
2
= mild dose
= medium dose
= strong dose
= The beverage is brewed by using the pre-ground coffee
9
SAECO ADAPTING SYSTEM
Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The Saeco coffee machine is equipped
with a self-adjusting system that allows the use of all types of coffee beans available on the market (not including flavored or carmelized).
• The machine automatically adjusts itself in order to optimize the extraction of the coffee, ensuring perfect compression of the beans to
obtain a creamy espresso coffee that is able to release all the aromas, regardless of the type of coffee used.
• The optimization process is a learning process that requires the brewing of a certain number of coffees to allow the machine to adjust the
compactness of the ground coffee.
• Attention should be given to special blends, which require grinder adjustments in order to optimize the extraction of the coffee.
COFFEE GRINDER ADJUSTMENT
The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used.
Important Note: Adjustments to the coffee grinder can be made only when the grinder is being used. This phase takes
place during the first part of a coffee brewing.
The adjustment can be carried out by using the dial inside the bean hopper without coming into contact with any moving parts.
Press and rotate the dial (one step at a time) according to the indications provided on the cover.
Press and turn the dial one notch at a time and brew 2-3 cups of coffee; this is the only way to notice differences in the grind.
A
Press and turn.
B
This setting provides a very coarse
grinding.
C
This setting provides a very fine grinding.
10
ADJUSTMENTS
DISPENSING SPOUT HEIGHT ADJUSTMENT
Before brewing a product, and according to the kind of cup, adjust the height of the dispensing spout.
To adjust, manually move the dispensing spout as shown in the picture.
1
2
3
4
Note: In some cases the dispensing spout can be removed to allow the use of very
large containers.
11
STAND-BY MODE
The machine is designed for energy saving. After 30 minutes of inactivity, the machine goes into stand-by mode, the boiler is no longer
heated and all the devices turn off.
Power consumption is reduced to a minimum. Press any button to turn the machine on again.
The machine status can be manually changed to stand-by mode by holding the stand-by button pressed for 3 seconds.
Note:
1 The stand-by mode cannot be activated if the service door is left open.
2 The stand-by activation time can be changed in the "MACHINE MENU" on
page 28.
3 When the stand-by mode is activated, the machine performs a rinse
cycle of the internal circuits, if necessary. The cycle can be interrupted by
pressing the "STOP" button.
The machine can be turned on again by executing one of the following actions:
1 By pressing any of the control panel buttons.
2 By opening the service door (when closing the door the machine goes back to standby mode).
A
When the machine is in stand-by mode
the frame of the " " button blinks.
SCREEN SAVER
The machine comes with a screen saver which is intended to extend the life of the display.
After 5 minutes of inactivity the machine logo will start floating on the display surface.
In this condition the machine is active and pressing any button will immediately activate all functions. If you wish to brew a cup of coffee
you will just need to press the corresponding button.
Note: The screen saver is not activated if there is an alarm.
12
MILK CARAFE USE
The machine is equipped with a carafe allowing for optimal milk frothing for the brewing of
tasty cappuccinos, latte macchiatos and any milk-based beverage.
I
A
The container allows for an easy and practical steaming and frothing of milk. The container
can be easily removed from the machine after each use so that it can be placed back in the
refrigerator.
The brewing circuit is automatically washed by an automatic cleaning cycle after each use.
This automatic cleaning cycle works only if active (see page 31) and can be also manually
started by pressing the "CLEAN" button next (see page 17).
The carafe must be removed at least once a week to allow for proper cleaning of all
components and keep all parts fresh for optimum brewing. (For proper cleaning, refer to the
"Milk Carafe Cleaning" section see page 41).
1
Remove the protection cover from the
milk container connection and keep it in
a clean place. It is suggested to insert it
in the water cover seat.
4
Fill the carafe with cold milk. Fill milk to
above the "MIN" line, but do not exceed
the "MAX" level indicated on the carafe.
2
Rotate the handle clockwise to
disengage the lock.
5
Place the lid back and ensure that it is
closed correctly. Move the handle back
to its central position to allow for perfect
closure.
B
B
Note: Before using the carafe, make sure it is thoroughly clean and sanitary. If
milk is left in the carafe, make sure it is still suitable for food consumption before
using it.
A = Carafe holes
B = Carafe pins
II
C
D
C = Machine couplings
D = Guides for carafe pins
3
Press the disengage buttons to allow the
lid removal.
6
Insert the carafe inclined towards the
front.
The carafe base should be positioned on
the hole (E) located on the drip tray.
13
7
8
C
A
D
B
B
At this stage the carafe holes (A) are
lower than the couplings (C).
The carafe pins (B) are located at the
same height of the guides (D).
Insert the carafe by turning it towards the base through a round movement (as shown
in the figure), until it is hooked to the hole (E) located in the drip tray.
9
DO NOT FORCE THE INCLINATION OF THE CARAFE.
E
The carafe will be naturally back in
place.
REMOVING THE CARAFE
The following operations show how to properly remove the carafe from the machine.
DO NOT FORCE THE INCLINATION OF THE CARAFE.
1
2
Pull the carafe upwards until its release from the hole (E) located in the drip tray. Then
pull until it releases.
After use, remove the container from the machine and place it in the refrigerator for proper conservation.
We recommend NOT to keep the container at room temperature for too long. Maximum 10 minutes.
Store the milk according to producer's instructions and do NOT use it after best-before date.
Wash the container as described in the "MILK CARAFE CLEANING" section (see page 41).
14
COFFEE BREWING
ESPRESSO / COFFEE / LONG COFFEE
This procedure shows how to brew an espresso. To brew another type of coffee, press the appropriate button. Use proper coffee cups to
prevent coffee from spilling.
To brew 2 cups, press the button twice; the machine brews half of the entered quantity and briefly interrupts dispensing in order to grind
the second coffee dose. Coffee brewing is then restarted and completed.
1
2
Position 1 or 2 cups to brew one or two
espresso coffees.
4
3
Place 1-2 cup(s) in position to brew a cup
of coffee or a cup of long coffee.
Choose the beverage by pressing the
corresponding button: once for 1 cup and
twice for 2 cups.
5
ESPRESSO
ESPRESSO
STOP
The machine starts grinding the selected
coffee quantity.
The machine begins brewing the
selected beverage.
6
ESPRESSO
Coffee brewing can be stopped at any time by
pressing "STOP".
STOP
The machine finishes brewing automatically on the basis of the quantity determined by the factory settings.
To customize this quantity, see page 24.
15
BEVERAGE BREWING WITH PRE-GROUND COFFEE
The machine allows you to use pre-ground and decaffeinated coffee.
Pre-ground coffee must be poured into the bypass doser positioned on the top of the machine. Only use ground coffee for espresso
machines and never coffee beans or instant coffee (see the "beverage programming" section on page 24).
This example shows how to brew an espresso by using pre-ground coffee.
1
2
Place 1 cup under the dispensing spout.
4
Press the opti-dose once or more until
the icon appears on the display screen.
5
OK
3
Select the product desired by pressing
the corresponding button.
6
OK
INSERT
GROUND COFFEE
AND PRESS OK
ESC
INSERT
GROUND COFFEE
AND PRESS OK
ESC
A message reminds the user to pour
ground coffee into the bypass doser.
Lift the door and open it.
Fill the measuring scoop provided and
use it to pour ground coffee in the
appropriate compartment.
Press "OK" to start brewing.
WARNING: ONLY PUT PRE-GROUND COFFEE INTO THE BYPASS DOSER WHEN YOU WISH TO BREW THIS TYPE
OF PRODUCT.
ONLY INSERT ONE SCOOP OF GROUND COFFEE AT A TIME. TWO COFFEES CANNOT BE BREWED AT THE SAME
TIME WHEN USING THIS FUNCTION.
Note:
• If brewing does not start within 30 seconds from the appearance of the message in step 4, the machine will return to the main
menu and discharge any inserted coffee into the used grounds drawer.
• If no pre-ground coffee is poured into the bypass doser, only water will be dispensed;
• If the dose is excessive or if 2 or more scoops of coffee are added, the machine will not brew the product and the coffee in the
bypass doser will be discharged into the used grounds drawer.
Clean the ground coffee compartment regularly (see "General Machine Cleaning" section).
16
CAPPUCCINO
PRODUCT BREWING
AT THE BEGINNING OF THE DISPENSING PHASE, THE MACHINE MAY PRODUCE SOME SPURTS OF MILK AND
STEAM: RISK OF SCALDING! ALWAYS WAIT FOR THE CYCLE TO END BEFORE REMOVING THE CONTAINER.
REFER TO THE SECTION "MILK CARAFE USE" (SEE PAGE 12).
When brewing milk products, the machine dispenses the milk first and then brews the coffee.
In this case, simultaneously brewing a double product is not possible.
1
2
Place the cup or the container where the
Cappuccino will be brewed.
4
3
Rotate the handle upper part of the
container on the cup. To avoid spilling
milk, always use cups of adequate size.
5
CAPPUCCINO
PLEASE WAIT …
The machine starts brewing: it grounds
the coffee and warms up to dispense milk.
In this case the ECOMODE function is set to
"ON" (see page 28).
Select the desired milk product by
pressing the corresponding button: you
can select only one milk product at a
time.
6
CAPPUCCINO
STOP
Milk dispensing begins. This operation
can be stopped by pressing "STOP".
CAPPUCCINO
STOP
Once milk has been dispensed, the
machine starts brewing the coffee. This
operation can be stopped by pressing
"STOP".
The machine requires a certain waiting time because the ECOMODE function is activated to allow energy saving.
Preparing cappuccino and other milk beverages can be a quicker operation if the ECOMODE function is deactivated; this, however, at the
expense of energy saving.
This function can only be deactivated by means of the "MACHINE MENU" (see page 28).
CICLO PULIZIA: CLEAN
7
17
8
Wait a few seconds. The machine
starts the automatic cleaning
process (if enabled - see page 31).
At the end remove the cup with the
cappuccino and place the handle back to
the initial position.
Upon completion of the cleaning cycle
remove the milk carafe and put it in the
refrigerator.
NEVER SEIZE THE CARAFE HANDLE DURING THE CLEANING CYCLE: RISK OF SCALDING!
The procedure is similar to prepare hot milk (please refer to the "special" beverages section - see page 20).
CLEANING CYCLE
The machine allows executing a quick cleaning cycle at any time.
The cleaning cycle can be executed before and/or after the beverage brewing.
This option allows you to manage the container cleaning process as desired.
The cleaning process may be used also for circuit sanitization after a long period of inactivity.
1
2
Place the container as described on
pages 12 and 13. The cleaning cycle only
involves the lines in contact with the
milk and it is carried out independently
of the presence of milk in the container.
Press the cleaning cycle button. The
machine executes an additional cleaning
cycle.
3
At the end it is possible to remove the
milk carafe now ready for use.
To properly insert/remove the carafe, refer to the instructions on page 12 and 13.
18
LATTE MACCHIATO
PRODUCT BREWING
AT THE BEGINNING OF THE DISPENSING PHASE, THE MACHINE MAY PRODUCE SOME SPURTS OF MILK AND
STEAM: RISK OF SCALDING! ALWAYS WAIT FOR THE CYCLE TO END BEFORE REMOVING THE CONTAINER.
REFER TO THE SECTION "MILK CARAFE USE" (SEE PAGE 12).
When brewing milk products, the machine dispenses the milk first and then brews the coffee.
In this case, simultaneously brewing a double product is not possible.
1
2
Place the cup or the container where the
Latte Macchiato will be brewed.
4
3
Rotate the handle upper part of the
container on the cup. To avoid spilling
milk, always use cups of adequate size.
5
LATTE MACCHIATO
PLEASE WAIT …
The machine starts brewing: it grounds
the coffee and warms up to dispense milk.
In this case the ECOMODE function is set to
"ON" (see page 28).
Select the desired milk product by
pressing the corresponding button: you
can select only one milk product at a
time.
6
LATTE MACCHIATO
STOP
Milk dispensing begins. This operation
can be stopped by pressing "STOP".
LATTE MACCHIATO
STOP
Once milk has been dispensed, the
machine starts brewing the coffee. This
operation can be stopped by pressing
"STOP".
The machine requires a certain waiting time because the ECOMODE function is activated to allow energy saving.
Preparing cappuccino and other milk beverages can be a quicker operation if the ECOMODE function is deactivated; this, however, at the
expense of energy saving.
This function can only be deactivated by means of the "MACHINE MENU" (see page 28).
CICLO PULIZIA: CLEAN
7
19
8
Wait a few seconds. The machine
starts the automatic cleaning
process (if enabled - see page 31).
At the end of the process remove the cup
with the Latte Macchiato and place the
handle back to the initial position.
Upon completion of the cleaning cycle
remove the milk carafe and put it in the
refrigerator.
NEVER SEIZE THE CARAFE HANDLE DURING THE CLEANING CYCLE: RISK OF SCALDING!
The procedure is similar to prepare hot milk (please refer to the "special" beverages section - see page 20).
CLEANING CYCLE
The machine allows executing a quick cleaning cycle at any time.
The cleaning cycle can be executed before and/or after the beverage brewing.
This option allows you to manage the container cleaning process as desired.
The cleaning process may be used also for circuit sanitization after a long period of inactivity.
1
2
Place the container as described on
pages 12 and 13. The cleaning cycle only
involves the lines in contact with the
milk and it is carried out independently
of the presence of milk in the container.
Press the cleaning cycle button. The
machine executes an additional cleaning
cycle.
3
At the end it is possible to remove the
milk carafe now ready for use.
To properly insert/remove the carafe, refer to the instructions on page 12 and 13.
20
SPECIAL BEVERAGES
SPECIAL BEVERAGES
The machine is designed to brew other beverages not displayed on the main menu.
Note: If no product is selected, the machine goes back to the main menu.
STEAM DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER. DANGER OF BURNS. THE STEAM / HOT
WATER WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE A CLOTH OR THE
SPECIAL HANDLE TO TURN IT.
1
2
Press the button to access the menu.
4
3
SPECIAL BEVERAGES
SPECIAL BEVERAGES
HOT MILK
HOT WATER
STEAM
HOT MILK
HOT WATER
STEAM
The display shows the page for
"SPECIAL" beverages.
5
SPECIAL BEVERAGES
HOT MILK
HOT WATER
STEAM
When the desired beverage has been
selected, press (OK) to start preparation.
See the following sections to brew
a special beverage.
Note: The machine goes back to the
main menu after 10 seconds
Select the desired beverages by pressing
button ( ) or ( ).
21
HOT MILK
This specific programme allows brewing hot milk.
1
2
3
SPECIAL BEVERAGES
HOT MILK
HOT WATER
STEAM
Place the cup. Rotate the upper part of
the container handle on the cup.
After selecting "HOT MILK" press (OK).
At the end of the brewing procedure,
take the cup with the milk.
CLEANING CYCLE
The machine allows executing a quick cleaning cycle at any time.
The cleaning cycle can be executed before and/or after the beverage brewing.
This option allows you to manage the container cleaning process as desired.
The cleaning process may be used also for circuit sanitization after a long period of inactivity.
1
2
Place the container as described on
pages 12 and 13. The cleaning cycle only
involves the lines in contact with the
milk and it is carried out independently
of the presence of milk in the container.
Press the cleaning cycle button. The
machine executes an additional cleaning
cycle.
3
At the end it is possible to remove the
milk carafe now ready for use.
To properly insert/remove the carafe, refer to the instructions on page 12 and 13.
22
SPECIAL BEVERAGES
HOT WATER DISPENSING
DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER. DANGER OF BURNS. THE STEAM / HOT
WATER WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE A CLOTH OR THE
SPECIAL HANDLE TO TURN IT.
1
2
3
SPECIAL BEVERAGES
HOT MILK
HOT WATER
STEAM
Place a container beneath the hot water
/ steam wand.
After selecting the "HOT WATER" option,
press (OK) and wait for the programmed
quantity to be dispensed. This operation
can be stopped by pressing "STOP".
When hot water dispensing is complete
remove the container with the desired
water quantity.
Repeat the procedure to dispense a new quantity of hot water.
After dispensing, some water always remains in the lines and this may result in leaking. This is a normal feature of the machine.
STEAM DISPENSING
Steam can be used to heat milk, water or other beverages.
STEAM DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER. DANGER OF BURNS. THE STEAM / HOT
WATER WAND MAY REACH HIGH TEMPERATURES: DO NOT TOUCH IT WITH BARE HANDS. USE A CLOTH OR THE
SPECIAL HANDLE TO TURN IT.
1
2
3
SPECIAL BEVERAGES
HOT WATER
STEAM
Place a container beneath the hot water
/ steam wand.
After selecting the "STEAM" option,
press (OK) and wait for the programmed
quantity to be dispensed.
Steam dispensing can be interrupted at
any time by pressing "STOP".
When steam dispensing complete remove
the container with the heated beverage.
For better results we recommend performing slow circular movements.
BEVERAGE LENGTH QUICK PROGRAMMING
23
BREWING MAY BE PRECEDED BY SHORT SPURTS OF MILK AND STEAM: RISK OF SCALDING! REFER TO THE SECTION
"MILK CONTAINER USE".
This section shows the programming procedure for the Cappuccino. This is meant as an example to introduce you to the steps necessary for
a quick and easy programming of all the beverages.
After a quick programming of the beverage, it is possible to carry out a finer and more detailed adjustment by means of the "BEVERAGE
MENU" (see page 24).
1
2
Place the cup or the container where
the cappuccino or latte macchiato will
be brewed.
4
3
Rotate the upper part of the container
handle on the cup. Use your everyday
cup.
5
CAPPUCCINO
6
CAPPUCCINO
CAPPUCCINO
MEMO
PLEASE WAIT …
The machine starts brewing: coffee is
ground and milk is heated up to prepare
for dispensing.
Hold the button pressed for 3 seconds to
start programming.
MEMO
MEMO
STOP
Milk dispensing begins. When the
desired quantity has been reached, press
"STOP".
STOP
Once milk has been dispensed, the
machine starts brewing the coffee. When
the desired quantity has been reached,
press "STOP".
Beverage length has been programmed. From now on, this length will be applied to the brewing of this beverage.
For the other beverages: hold pressed the button of the beverage to be programmed and follow the same procedure.
24
BEVERAGE MENU
All beverage settings can be customized.
1
2
MENU
BEVERAGE MENU
MACHINE MENU
Press the MENU button to access the
machine main menu.
Press the OK button to access the
BEVERAGE MENU.
Selection/confirmation button
Scrolling/Selection button
BEVERAGE MENU
ESPRESSO
COFFEE
CAFFE’ LUNGO
Exit button
DEFAULT
Scrolling/Selection button
For each beverage it is possible to reset the original factory settings. After selection of this
function, the customized settings are deleted.
25
In this case we look at how to programme a customized cappuccino.
The milk managing options are not shown when a coffee brewing (espresso or long coffee) is being programmed.
CAPPUCCINO
COFFEE QUANTITY
PREBREWING
COFFEE TEMPERATURE
COFFEE QUANTITY
PREBREWING
COFFEE TEMPERATURE
COFFEE LENGTH
This section allows you to program the quantity of coffee to grind for the beverage
brewing: this setting will affect the coffee aroma.
GROUND COFFEE = The beverage is brewed by using the pre-ground coffee
MILD = mild dose
MEDIUM = medium dose
STRONG = strong dose
Prebrewing: Coffee is slightly dampened before brewing so as to bring out the full aroma
of the coffee which acquires an excellent taste.
OFF: prewbrewing function is not performed.
LOW: prewbrewing function is active.
HIGH: prebrewing function is longer in order to bring out the coffee taste.
This section allows you to program the temperature for coffee brewing.
LOW: low temperature.
NORMAL: medium temperature.
HIGH: high temperature.
This section allows to program the quantity of water to be used for each selected
beverage. The strip allows you to determine exactly the quantity of water for preparing
coffee.
26
BEVERAGE MENU
CAPPUCCINO
COFFEE QUANTITY
PREBREWING
COFFEE TEMPERATURE
MILK QUANTITY
This section allows you to program the quantity of milk for each selected beverage. The
strip allows you to determine exactly the quantity of milk to be dispensed.
Access to the "HOT WATER" menu is gained from the "SPECIAL BEVERAGES" menu.
HOT WATER
WATER QUANTITY
DEFAULT
WATER QUANTITY
This section allows you to program the quantity of water to be dispensed when pressing
the hot water button. The strip allows you to determine exactly the quantity of water to
be dispensed.
MACHINE MENU
The machine allows you to customize the operation settings.
1
2
2
MENU
BEVERAGE MENU
MACHINE MENU
1
Press the MENU button to access the
machine main menu.
Select the menu by pressing the ( )
button. Press the OK button to access the
MACHINE MENU.
Selection/confirmation button
Scrolling/Selection button
MACHINE MENU
GENERAL MENU
DISPLAY MENU
WATER MENU
Exit button
Scrolling/Selection button
27
28
MACHINE MENU
GENERAL MENU
To change the machine operation settings.
GENERAL MENU
This function activates/deactivates the acoustic alarms.
TONE
OFF
To deactivate the acoustic alarms
ON
To activate the acoustic alarms
This function enables allows you to choose how the boilers on the machine
are activated, to promote energy saving.
The function is set by default to «OFF».
ECOMODE
OFF
This function activates all the boilers each time the machine
starts up to be immediately able to dispense all kinds of
beverages. This function entails greater energy consumption.
ON
This function activates only the coffee boiler each time the
machine starts up. The machine saves energy but takes longer to
dispense milk-based beverages.
STAND-BY SETTINGS
To set the time interval for the machine to go into stand-by mode after the
last brewing. The default time value is «after 30 minutes».
15 MINUTES
30 MINUTES
60 MINUTES
180 MINUTES
Press any button to turn the machine on again. After performing
the function diagnostics and the warm-up phase, the machine is
again ready for use.
29
MENU DISPLAY
DISPLAY MENU
This menu allows you to set the menu language and the display brightness.
This setting is of fundamental importance for correctly adjusting the
parameters of the machine according to the country where the machine is used.
LANGUAGE
ENGLISH
BRIGHTNESS
The currently selected language is displayed.
To set the correct display brightness according to the room illumination.
30
MACHINE MENU
WATER MENU
This menu allows setting correct water parameters for coffee brewing.
WATER MENU
HARDNESS
ENABLE FILTER
ACTIVATE FILTER
To change the machine water hardness setting.
The "Hardness" function allows adjusting the machine to the level of
hardness of the water used. The machine will then request descaling at the
right moment.
Measure water hardness as shown on page 5.
To activate/deactivate the warning signal to replace the water filter. By
activating this function, the machine notifies the user when the water filter
needs to be replaced.
OFF: Warning disabled.
ON: Warning enabled (this value is automatically set when the filter is
activated).
To activate the filter after its installation or replacement. Refer to the relevant
section on page 7 to correctly install and/or replace the filter.
31
MAINTENANCE
This menu allows setting all the functions for correct machine maintenance
MAINTENANCE
This function shows how many products have been brewed for every single
type of coffee since the last reset.
COUNTERS
BREW GROUP CLEAN
This function enables the wash cycle for the brew group (See page 32).
This function enables the wash cycle for the carafe used for preparing milk
beverages (See page 36).
Note: This wash cycle is fundamental for a correct maintenance of
the carafe.
CARAFE CLEANING
This function enables the descaling cycle (See page 33).
DESCALING
This function enables automatic cleaning of the carafe after each dispensing
of milk-based products.
CARAFE CLEAN
OFF
The self-cleaning function is disabled.
ON
The self-cleaning function is enabled.
FACTORY SETTINGS
FACTORY SETTINGS
This function allows you to restore all factory settings.
Note: By restoring the factory settings, all the personal parameters are lost.
32
MAINTENANCE
BREW GROUP CLEANING CYCLE
To wash the Brew Group, simply clean with water as shown on page 40. This wash completes the maintenance process of the Brew Group. We
recommend that you carry out this cycle on a monthly basis or every 500 coffee brewings by using the Saeco tablets, which can be purchased
separately at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.
WASH CYCLES CANNOT BE STOPPED. DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION.
Turn the SBS dial all the way to the left, counter-clockwise, (see page 11) before starting the cycle.
MENU -> MACHINE MENU -> MAINTENANCE
1
2
3
MAINTENANCE
OK
COUNTERS
BREW GROUP CLEAN
CARAFE CLEANING
ESC
Select the menu option.
Press the "OK" button to confirm.
4
Press the "OK" button to confirm.
5
7
PLACE A CONTAINER
UNDER THE
DISPENSING SPOUT
After placing the container, press the
"OK" button.
Fill the water tank with fresh drinking
water up to the "MAX" level. Then, press
the "OK" button.
INSERT GROUP
CLEAN TAB
After inserting the tablet, press the "OK"
button.
8
OK
REFILL
WATER TANK
6
OK
Insert the cleaning tablet into the bypass
doser.
OK
PERFORM BREW
GROUP CLEANING?
Place a container under the coffee
dispensing spout.
9
BREW GROUP CLEAN
The cleaning cycle for the brew group is
performed automatically.
At the end of the cycle, remove the
container and empty it appropriately.
After the cycle, set the SBS dial to the desired position (see page 8).
Clean the brew group as described in the "Brew Group Cleaning" section (see page 40).
33
BOILER DESCALING CYCLE MENU
A descaling cycle is necessary when indicated by the machine. The machine must be on and controls the distribution of the descaling
solution automatically. This operation must be carried out before your coffee machine stops working, as in this case repair is not covered by
warranty. The descaling solution and the complete "Maintenance Kit" can be purchased at your local dealer, at the Philips on-line shop at
http://shop.philips.com or at authorised service centres.
In case of conflict, priority must be given to what is indicated in the operation and maintenance manual over the
instructions provided on separately sold accessories and materials.
DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION.
WARNING! NEVER USE VINEGAR AS A DESCALING SOLUTION.
Only use the Saeco descaling solution, especially designed to respect the technical features of the machine, to ensure its performance
will not decrease with time, and for a safe and risk-free use. The descaling solution is to be disposed of according to the manufacturer’s
instructions and/or regulations in force in the country of use.
Note: Before starting a descaling cycle make sure that:
1. THE INTENZA WATER FILTER HAS BEEN REMOVED
2. A container of adequate size or a couple of containers are available and are placed in the points identified
DESCALING AND/OR RINSE CYCLES CANNOT BE STOPPED; ALL THE PHASES MUST BE COMPLETED. IF THE MACHINE IS
SWITCHED OFF OR IN CASE OF POWER FAILURES, THE INTERRUPTED CYCLE MUST BE REPEATED FROM THE BEGINNING.
HOWEVER, CYCLES MAY BE PAUSED BY PRESSING THE "PAUSE" BUTTON; IT WILL BE POSSIBLE TO RESUME THE CYCLE AT
ANY TIME BY PRESSING THE "START" BUTTON.
TURN THE SBS DIAL ALL THE WAY TO THE LEFT, COUNTER-CLOCKWISE (SEE PAGE 8), BEFORE STARTING THE CYCLE.
MENU -> MACHINE MENU -> MAINTENANCE
Note: During the descaling cycle, some alarm messages may appear to allow for a correct management of the machine.
After resetting the message, always press the "START" button to resume the descaling cycle.
1
2
3
MAINTENANCE
OK
CARAFE CLEANING
DESCALING
CARAFE CLEAN
ESC
Select the menu option.
Press the "OK" button to confirm.
START DESCALING?
Warning: Once this selection is made, the
whole cycle will have to be completed.
Press the "OK" button to confirm or "ESC"
to exit
OK
FILL TANK WITH
DESCALING SOLUTION
Pour the entire content of the Saeco
concentrated descaling solution into the
water tank, and then fill the tank with
fresh water up to the MAX level.
Then, press the "OK" button.
34
MAINTENANCE
4
5
OK
OK
EMPTY TRAY UNDER
BREW GROUP
Empty the drip tray placed under the
dispensing spout (page 38) and then
replace it on the machine.
Then, press the "OK" button.
7
6
OK
FILL HALF CARAFE
WITH WATER. INSERT
IN BREW. POSITION
Fill half the carafe with fresh water
(page 36).
Insert the carafe and place it in the
brewing position. Then, press the "OK"
button.
8
STEP 1/2 DESCALING
PLACE A CONTAINER
UNDER HOT WATER &
CARAFE DISP SPOUT
Place a container under the dispensing
spout and a container under the hot
water wand.
Then, press the "OK" button.
9
OK
STEP 1/2 DESCALING
PAUSE
RINSE TANK &
FILL WITH WATER
PAUSE
The descaling cycle is activated.
The bar shows the cycle's progress.
If the containers need to be emptied,
press the "PAUSE" button.
Then, press the "START" button when the
container has been emptied and replaced.
At the end of the first step, when the
descaling solution is finished, the
machine will require a tank rinse.
A default amount of water is needed for the rinsing step.
This allows performing an ideal rinse cycle to ensure the best conditions to brew products.
The message about filling the tank for the rinse cycle is normal, as it is part of the procedure.
10
12
11
OK
RINSE TANK &
FILL WITH WATER
Rinse the tank and fill it again with fresh
drinking water up to the "MAX" level.
Then, press the "OK" button.
OK
EMPTY TRAY UNDER
BREW GROUP
Empty the drip tray placed under the
dispensing spout (page 38) and replace it
back onto the machine.
Then, press the "OK" button.
OK
FILL HALF CARAFE
WITH WATER. INSERT
IN BREW. POSITION
Completely empty the carafe (page 36)
and fill it with fresh water.
Insert the carafe in the brewing position,
and then press the "OK" button.
35
13
14
OK
PLACE A CONTAINER
UNDER HOT WATER &
CARAFE DISP SPOUT
15
STEP 2/2 RINSING
PAUSE
Place a container under the dispensing
spout and a container under the hot
water wand.
Then, press the "OK" button.
The rinse cycle is activated.
The bar shows the cycle progress.
STEP 2/2 RINSING
PAUSE
If the containers need to be emptied,
press the "PAUSE" button
Then, press the "START" button when the
container has been emptied and replaced.
16
At the end of the second step, the
machine is ready for use.
All the components should then be rinsed.
After rinsing them, dry them carefully and fit them back into their seats.
Set the SBS dial to the desired position (see page 8).
36
MAINTENANCE
MILK CIRCUIT MAINTENANCE
The milk circuits can be sanitized by carrying out a simple and quick cycle allowing for a thorough cleaning. This wash completes the
maintenance process of the milk container. We recommend that you carry out this cycle on a monthly basis by using the Saeco detergent,
which can be purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.
WASH CYCLES CANNOT BE STOPPED.
DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION.
MENU -> MACHINE MENU -> MAINTENANCE
1
2
3
MAINTENANCE
OK
BREW GROUP CLEAN
CARAFE CLEANING
DESCALING
ESC
Select the option from the "CARAFE
CLEANING" menu.
Press the "OK" button to confirm.
4
The carafe must be removed from the
machine and its content emptied.
Disengage the handle by rotating it
clockwise.
7
Place the lid back and ensure that it is
closed correctly.
OK
START CARAFE
WASHING?
Press the "OK" button to confirm.
5
Press on the sides and lift the lid.
8
Move the handle back to its central
position to allow for perfect closure.
REFILL
WATER TANK
Fill the tank with fresh drinking water up
to the "MAX" level.
Press the "OK" button to confirm.
6
Fill the carafe with fresh drinking water
up to the MAX level.
Add the content of a detergent packet to
the milk carafe.
9
Insert the carafe inclined towards the
front.
The carafe base should be positioned on
the hole (E) located on the drip tray.
37
10
11
C
A
D
B
B
At this stage the carafe holes (A) are
lower than the couplings (C).
The carafe pins (B) are located at the
same height of the guides (D).
Insert the carafe by turning it towards the base through a round movement (as shown
in the figure), until it is hooked to the hole (E) located in the drip tray.
12
13
14
OK
POUR DETERGENT
INTO CARAFE & FILL
WITH WATER
E
The carafe will be naturally back in
place.
Place a large empty container under the
dispensing spout. Rotate the upper part of
the milk carafe directly above the container.
Press the "OK" button to confirm.
15
16
17
OK
CARAFE CLEANING
REFILL
WATER TANK
The cleaning cycle is activated.
The bar shows the cycle progress.
When the wash is complete, fill the
tank with fresh drinking water up to the
"MAX" level.
Press the "OK" button to confirm.
18
19
CARAFE RINSING
Place a large empty container under the
dispensing spout. Rotate the upper part of
the milk carafe directly above the container.
OK
FILL CARAFE
WITH FRESH WATER
Remove the carafe, rinse and fill it again
with fresh drinking water up to the
"MAX" level.
Press the "OK" button to confirm.
Upon completion of the cleaning
cycle, we recommend rinsing all the
components under fresh drinking water.
The rinse cycle is activated. The bar shows the cycle progress.
At the end of the cycle, the machine returns to the product brew menu page.
38
CLEANING
MAINTENANCE DURING OPERATION
During normal operation, the following messages may appear: "Empty coffee grounds drawer" and/or "Empty drip tray". This operation
must be performed when the machine is on.
1
Press the button and open the service
door.
4
Empty and wash the drip tray and the
cover with fresh water.
2
Remove the drip tray and used grounds
drawer.
5
Correctly reinstall all the components.
3
Empty the used grounds drawer and
wash it with fresh water.
6
Insert the tray and the coffee grounds
drawer and close the service door.
If the used grounds drawer is emptied when the machine is off, the coffee grounds counter is not reset. For this reason the machine might
display the "Empty coffee grounds drawer" message after brewing just a few coffees.
39
GENERAL MACHINE CLEANING
The cleaning procedure described below must be carried out at least once a week.
Note: If water remains in the tank for several days, do not use it.
WARNING! Never immerse the machine in water.
1
Turn off the machine and unplug it.
4
Remove the grill and wash it thoroughly.
7
Remove the dispensing spout and wash
it with water.
2
Take out the water tank and wash it with
fresh water.
5
Remove the support under the grill. Wash
it taking care of the seal area. Reinstall
the support only after washing the inside
of the water recovery tray.
8
Clean the pre-ground coffee
compartment with a brush or a dry cloth.
3
Take out the water recovery tray.
6
Wash the water recovery tray. After
drying it, reassemble and reinsert it in
the machine.
9
Clean the steam wand and the display
with a dry cloth.
40
CLEANING
BREW GROUP CLEANING
Wash the brew group at least once a week. Before removing the group, remove the used grounds drawer as shown in fig. 2 on page 38.
Wash the brew group with lukewarm water.
Lubricate the Brew Group every 30 days or after approximately 500 brewing cycles. The grease to lubricate the Brew Group can be
purchased at your local dealer, at the Philips on-line shop at http://shop.philips.com or at authorised service centres.
WARNING! Do not wash the brew group with detergents that may compromise its correct operation. Do not wash it in the
dishwasher.
1
Press the PUSH button to remove the
brew group.
4
Apply the lubricant evenly on both side
guides.
7
The lever on the rear part of the group
must be in contact with the group
base.
2
Wash the brew group and the filter and
dry.
5
Make sure the brew group is in rest
position; the two references must match.
8
Insert the washed and dried brew group.
DO NOT PRESS THE “PUSH” BUTTON.
3
Lubricate the brew group guides using
the supplied lubricant.
6
Make sure the components are in the
correct position. The hook shown must
be in the correct position; to check its
position, firmly press the “PUSH” button.
9
Insert the used grounds drawer
and close the service door.
41
MILK CARAFE CLEANING
The carafe must be removed and properly washed at least once a week.
This procedure guarantees the perfect sanitation of all components.
Note: Pay attention to how the components are assembled. This little shrewdness will facilitate the subsequent
reassembling.
1
2
The carafe must be removed from the
machine and emptied for its cleaning.
4
Disengage the handle by rotating it
clockwise.
5
Rotate the handle counter-clockwise to
the unlock position.
7
Remove the connector which is in
contact with the machine.
8
Remove the suction hose.
Remove the external fitting by pulling it.
3
Press on the sides and lift the lid.
6
Remove the handle with the suction
hose.
9
Remove the internal fitting.
All components can be thoroughly washed with hot water.
After washing the components, reassemble them by following the instructions on next page.
Do NOT wash the carafe components in the dishwasher.
42
CLEANING
MILK CARAFE ASSEMBLY
Pay attention during the assembly phase. In case the components do not smoothly enter in their positions, read the instructions more
carefully and repeat the assembly procedure.
1
Insert the inner fitting in the hose and
press until fully inserting it.
4
Insert the unit previously assembled
in the cover base. Pay attention to the
reference.
7
Fit the cover on the carafe.
2
Insert the outer fitting in the inner
fitting. Refer to the arrow in the figure for
the direction of insertion.
5
Insert the outer cover in the base guides.
8
Rotate the handle anti-clockwise to
bring it to the locked position.
3
Insert the hose in the external fitting (up
to the limit point).
6
Rotate the handle clockwise up to the
( ) symbol.
9
The carafe is now ready for use.
MACHINE WARNINGS
Help Message Displayed
CLOSE
HOPPER DOOR
ADD COFFEE
INSERT BREW GROUP
INSERT COFFEE
GROUNDS DRAWER
EMPTY COFFEE
GROUNDS DRAWER
CLOSE
FRONT DOOR
REFILL
WATER TANK
EMPTY DRIP TRAY
TURN CARAFE
INTO
BREWING POSITION
ESC
TURN CARAFE
INTO
RINSING POSITION
ESC
INSERT CARAFE
ESC
43
How to Reset the Message
Close or correctly place the coffee bean hopper inner cover to be able to prepare a
beverage.
Fill the coffee bean hopper with coffee beans.
Insert the brew group back in place.
Insert the coffee grounds drawer and the drip tray.
Remove the used grounds drawer and empty the coffee grounds into a suitable container.
Note: The used grounds drawer must be emptied only when the machine
requires it and with the machine on. If you empty the drawer with the machine
turned off it will not record the emptying operation.
Close the service door to make the machine functional.
Take out the tank and fill it with fresh drinkable water or top it up by means of the special
port.
Open the service door and empty the drip tray located under the brew group.
Warning: If this operation is performed when the machine is on, it will record
the used grounds drawer emptying and will reset the counter; therefore, it is
necessary to empty the coffee grounds as well.
A beverage with milk has been selected. The machine requires the carafe handle spout to
be placed into dispensing position.
Press the button "ESC" to cancel the selection.
The carafe rinse function has been selected.
Press the button "ESC" to cancel the selection.
The selected operation requires the milk container for brewing. Insert the container in the
machine as specified in the manual.
Press the button "ESC" to cancel the selection.
44
MACHINE WARNINGS
Help Message Displayed
How to Reset the Message
Perform a descaling cycle on the machine.
When this message is displayed, it is still possible to use the machine, but its correct
operation might be compromised.
Damages caused by failure to descale the machine are not covered by warranty.
The machine requests the "Intenza" water filter to be replaced with a new one. Replace the
filter as described on page 7.
The alarm is displayed only if the "Enable Filter" function is set to "ON".
(See page 30).
Flashing red light. Machine in Stand-by.
The Stand-by settings can be changed.
Press any button to start the machine.
RESTART TO SOLVE
An event has occurred which requires the machine restart.
Take note of the code (E xx) shown at the bottom.
Switch off the machine, wait 30 seconds and then switch it on again. If the problem
persists, contact the service centre.
SAFETY RULES
SOS
45
IN CASE OF EMERGENCY
IMMEDIATELY UNPLUG THE CORD FROM THE OUTLET.
ONLY USE THE APPLIANCE
•
•
•
•
Indoors.
For preparing coffee, hot water and for frothing milk.
For domestic use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
PRECAUTIONS FOR THE USE OF THE MACHINE
•
•
•
•
•
•
•
•
•
Do not use the machine for purposes other than those indicated above, in order to avoid danger.
Do not introduce any substances other than those indicated in the instruction manual.
During the normal filling of any reservoirs, all nearby reservoirs must be closed.
Fill the water tank only with fresh drinking water: Hot water and/or any other liquid may damage the machine.
Do not use carbonated water.
Do not put fingers or any material other than coffee beans in the coffee grinder.
Before manipulating the coffee grinder, turn of the machine’s main switch and unplug the cord.
Do not put instant coffee or whole bean coffee in the ground coffee container.
Only use your finger when operating the LCD screen.
CONNECTION TO ELECTRICAL POWER
The connection to the electrical network must be carried out in accordance with the safety regulations in force in the user’s
country.
The machine must be connected to a socket which is:
• compatible with the type of plug installed on the machine;
• suitably sized to comply with the data on the plate attached to the inside of the appliance.
• effectively grounded.
The power cord must not:
• come into contact with any type of liquid: danger of electric shocks and/or fire;
• be crushed and/or come in contact with sharp surfaces;
• be used to move the machine;
• be used if damaged;
• be handled with damp or wet hands;
• be wound in a coil when the machine is being operated.
• Be tampered with.
INSTALLATION
•
•
•
•
•
•
•
•
•
•
•
Choose a solid, stationary flat surface (no more than 2° of inclination).
Do not install the machine in areas where water could be sprayed.
Optimal operational temperature: 10°C - 40°C / 50-104 degrees Fahrenheit
Maximum humidity: 90%.
The machine should be installed in an adequately lit, ventilated, hygienic location and the electric socket should be within
easy reach.
Do not place on heated surfaces!
Install it at least 10 cm / 4” from the walls and cooking surfaces.
Do not use in places where the temperature may drop to a level equal to and/or lower than 0°C / 32 degrees Fahrenheit.
If the machine has been exposed to such conditions notify the customer service center, who will have to carry out a safety
check.
Do not use the machine near inflammable and/or explosive substances.
The machine must not be used in an explosive or volatile atmosphere or where there is a high concentration of dust or oily
substances suspended in the air.
Do not install the machine on top of other appliances.
46
SAFETY RULES
DANGERS
•
•
•
•
•
•
•
The appliance must not be used by children and persons who have not been informed of its operation.
The appliance is dangerous to children. When left unattended, unplug from the electrical outlet.
Keep the coffee machine packaging out of the reach of children.
Never direct the jet of hot water and/or steam towards yourself or others. Danger of scalding.
Do not insert objects through the appliance’s openings. (Danger! Electrical Current!).
Do not pull out the plug by yanking on the power cord or touching it with wet hands.
Warning. Danger of burning when in contact with hot water, steam and the hot water spout.
FAILURES
• Do not use the appliance if a failure has been verified or suspected, for example after being dropped.
• Any repairs must be performed by an authorized customer service center.
• Do not use the appliance with a defective power cord. The manufacturer or its customer service center will have to
replace the power cord if damaged. (Caution! Electrical Current!)
• Turn off the appliance before opening the service door. Danger of burns!
CLEANING / DESCALING
• For cleaning the milk and coffee circuits use only recommended detergents provided with the machine. These detergents
must not be used for other purposes.
• Before cleaning the machine, the main switch must be turned to OFF (0), unplugged from the socket and cooled down.
• Clean the machine with neutral detergent and a damp cloth (do not use abrasive sponges or steel wool pads).
• Keep the appliance from coming into contact with splashes of water or immersing in water.
• Do not dry the machine’s parts in conventional or microwave ovens.
• The machine and its components must be cleaned and washed after the machine has not been used for a certain period.
REPLACEMENT PARTS
For safety reasons, use only original replacement parts and original accessories.
WASTE DISPOSAL
- The packing materials can be recycled.
- Appliance: unplug the appliance and cut the power cord.
- Deliver the appliance and power cord to a service center or public waste disposal facility
This product complies with eu directive 2002/96/ec.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal service or the
shop where you purchased the product.
FIRE SAFETY
In case of fire, use Carbon Dioxide extinguishers (CO2).
Do not use water or dry-powder extinguishers.
ADDITIONAL INFORMATION FOR THE CORRECT USE OF THE INTENZA WATER FILTER
To correctly use the Intenza water filter, please consider the following instructions:
1. Store the Intenza water filter in a cool area in which the room temperature ranges from +1°C to +50°C (34°F to 122°F).
Do not store it in direct sunlight.
2. Carefully read the operating instructions and the safety warnings provided with each filter.
3. Keep the filter instructions together with the manual.
4. These instructions integrate those contained in the manual, as they focus on the specific application of the filter in the
machine.
47
del 30-06-12
02
EN
Rev.00
02
The manufacturer reserves the right to change the features of the product without prior notice.
www.philips.com/saeco
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising