Kennards ING, RYAN Turf Cutter User guide

23
Please read this guide carefully
before operating the equipment
MOST IMPORTANT - RISK ASSESS!!!
Before you commence any work at your chosen work
area, you should undertake some preliminary hazard
identification and risk control precautions. Ideally
more than one person should do this. This is
undertaken by:
1. Physically inspecting the work site
2. Reviewing the best way/job steps required to
complete the task
3. Reviewing the Safe Work Information supplied
with the equipment
4. Reviewing other reference documentation and
expert advice
The hazard identification and control process steps are
defined as:
1. Identify the Hazards (eg. 240V power drill use
around wet areas)
2. Assess the Risk (multi earth paths - possible
electrocution)
3. Select the Control Measure (e.g. dry the area; use
an RCD; use a cordless drill etc)
4. Re-assess the Risk (risk of electrocution now
negligible). This is undertaken to ensure that the
risk control measures adopted have not
introduced any new risks to the work area.
HELP
If the unit does not operate correctly or you are unhappy with
its performance, return it to the nearest Kennards Hire Centre
for exchange or phone for assistance. Do not attempt
repairs yourself.
Refer to your hire contract for details of our AFTER HOURS
EMERGENCY NUMBER.
PERSONAL PROTECTION EQUIPMENT (PPE)
HEARING
PROTECTION
PROTECTIVE
GLOVES
RESPIRATORY
PROTECTION
SAFETY
GLASSES
OVERALLS
STEEL TOE
CAPPED
BOOTS
BEFORE STARTING - ING make
1. Confirm you are using this make - ING
2. Ensure cutting blade is in raised position.
3. Ensure both clutches on the handles are forward in the
disengaged position.
4. Dig trench a little wider than blade and as deep as you
want to cut the turf.
TO SET BLADE POSITION
1. Move the depth adjusting lever (right hand side, forward
of handles) off the locating pin so you can raise or lower
the blade.
2. Select the depth of cut.
3. Align the pin into a hole on the lever that will maintain
the desired cutting depth.
Note: There is no “Pitch” adjustment on the Ing make
TO START
1. Turn fuel tap on.
2. Turn choke to closed position.
3. Pull starter rope until motor starts.
4. When motor starts, turn choke to open position.
5. To allow the machine to be power driven to work site,
ensure motor is running at idle then engage traction
clutch by pulling right hand lever towards you. At work
site disengage traction clutch (push lever forward)
before proceeding to step 6.
6. When ready to start operation, lower blade to desired
cutting depth by moving vertical lever on right hand side
of machine just forward of handle.
7. To start blade cutting, engage left hand clutch by pulling
towards you.
8. Adjust throttle lever either on motor or on handles
(depending on model) to achieve desired motor speed
according to conditions.
9. To move forward engage traction clutch as above.
10. When finished, reverse procedure:
- Disengage traction clutch (by pushing forward).
- Reduce throttle speed.
- Disengage left hand cutting blade clutch (by pushing
forward).
- Raise blade.
- Engage traction clutch to drive machine to transport.
- Disengage clutch and turn motor off.
Turf Cutter
SAFETY DO’S
General Safety Do’s
DO take your time to Read this User Guide and other
Safety material (e.g. manufacturer’s instructions) completely
and in its entirety BEFORE operating the Turf Cutter unit.
DO seek medical advice from your doctor if you have any
medical condition that may be affected by the operation and
manual handling of the Turf Cutter unit.
DO ensure that the equipment is suitable for your needs and
working environment.
DO ensure the supplier/hirer shows you how to use the
equipment and that you fully understand and are familiar
with the equipment and its operations including emergency
shut down/response.
DO ensure that the equipment is assembled and used
according to the manufacturers and hirer’s instructions.
DO check Turf Cutter controls for proper response.
DO always work from the correct operating area at all times.
DO wear appropriate PPE as illustrated.
DO ensure that the PPE you use has an Australian Standards
compliance label.
DO before operating, check area and remove any foreign
objects, which may present a safety hazard or damage the
Turf Cutter.
DO keep hands and feet well clear of cutting blades.
DO make sure all children and animals are kept away from
the Turf Cutter machine whilst in operation. If necessary erect
barricades around the work area.
DO always stop the Turf Cutter machine before leaving it
unattended.
DO ensure that you have clear access and egress to the work
area whilst on the job.
DO ensure the work environment is well lit with all aspects of
the job easily seen and discernable.
DO shut down the Turf Cutter machine if a fault is detected.
DO check the condition of the Turf Cutter unit at the start and
end of each day and report any damage or defects.
DO ensure that all guards are correctly attached and in good
condition.
DO stop the machine and regularly clear any build up of
material on or around machine.
DO be aware of terrain and avoid working on and across
slopes that may cause machine to tip or operator lose control.
Petrol Safety Do’s
DO always operate petrol units in well-ventilated areas.
A build up of petrol fumes (carbon monoxide) can KILL...
Do equalise fuel tank pressure to avoid vapour lock. Do this
by loosening the fuel cap and then retightening.
SAFETY DON’TS
General Safety Don’ts
DO NOT operate Turf Cutter if tired or suffering any medical
condition, or if under the influence of alcohol or drugs, which
may cause lethargy or danger to you or others.
DO NOT start the machine if a fault is detected
DO NOT operate in areas that contain flammable liquid, gas
or naked flames or sparks.
DO NOT cut near underground cables, pipes etc.
DO NOT work alone.
DO NOT ever allow persons or animals to ride on or play near
the equipment.
DO NOT leave Turf Cutter running whilst unattended.
DO NOT use a Turf Cutter that may have become damaged
(e.g. guarding).
DO NOT operate Turf Cutter without guards correctly fitted.
DO NOT ever force the Turf Cutter unit or use it to do a job for
which it was not designed.
DO NOT wear loose clothing, gloves, neckties, rings, bracelets
or other jewellery which may get caught in the moving parts;
tie back long hair or wear appropriate headwear to prevent
hair becoming entangled in rotating parts.
Petrol Safety Don’ts
DO NOT smoke while in the vicinity of petrol, petrol
containers or petrol-powered equipment
DO NOT smoke while using or refueling the unit.
DO NOT refuel the unit while it is running.
DO NOT start or use the unit within 3 metres of any fuel
containers.
DO NOT ever operate petrol units in areas that contain
flammable liquids or gas, or confined non-ventilated spaces.
DO NOT touch or lean on hot surfaces such as exhaust pipes.
TO STOP
1. Disengage drive lever.
2. Disengage blade lever.
3. Turn fuel tap off.
4. Depress stop button on motor.
BEFORE STARTING - RYAN make
1. Confirm you are using this make - RYAN
2. Ensure blade wheel drive and cutter drive levers are both
in the disengaged position.
3. Disengage clutch lever on handle (back position).
4. Ensure cutter blade is off the ground.
TO SET BLADE POSITION
1. Loosen blade depth lock lever.
2. Use blade depth lever to adjust.
3. Re-tighten blade pitch lock lever.
TO SET BLADE PITCH
1. Loosen pitch lock lever.
2. Adjust blade pitch by pushing lever forward or backward.
3. Re-tighten blade depth lock lever.
4. Engage wheel drive and cutter drive levers (see diagram
before starting).
5. Engage clutch (on handle) to forward position and
increase throttle speed (on handle or motor depending
on model).
6. Begin cutting.
7. At the end of each cut, disengage clutch (pull back
further for brake) and repeat the above procedure to do
your next run.
TO STOP
1. Disengage clutch (pull back all the way for brake.)
2. Disengage wheel blade and cutter blade drives.
3. Loosen and raise cutter blade off the ground.
4. Turn fuel tap off.
5. Depress stop button on motor.
MAINTENANCE
• Check all bolts and pins are secure.
• Check oil level.
• Check fuel level.
TROUBLESHOOTING
MOTOR NOT RUNNING
• Check fuel level
• Check fuel tap is turned on
• Check spark plug lead has contact
• Check air filter is dry
IF THE CUTTER IS RIPPING UP THE PITCH
• Check blade switch position (also see helpful hints for
suggestions on blade pitch)
• Lawn is too dry
HELPFUL HINTS
Always try to cut in the straightest row possible. The Turf
Cutter is not designed to cut in arcs or circles. It is easier to
roll a straight row of turf rather than a curved one.
When adjusting depth, a simple rule to follow is the thicker or
coarser the turf, the deeper the cutting blade should be.
It may be necessary to adjust the blade pitch if the ground is
very soft or very hard. For hard ground, set blade pitch at an
angle. For soft ground, set level to the ground. (Ryan make
only)
HANDLING
Always tie down your load when transporting.
To avoid manual handling injuries, adopt safe posture for
lifting and manoeuvring of the unit, if necessary obtain help
to manually lift and move the unit.
SPECIFICATIONS
RYAN
ING
Weight
120kg
130 kg
Power
5.5hp (5.6 kilowatts) 7.5hp (2:1 Reduction)
Depth of Cut 50-60mm
Width of Cut 300mm
350mm
Fuel Type
Unleaded
Unleaded
Tank Capacity 4.5 Litres
4.5 Litres
This operating and safety brochure is intended as a guide only for the safe operation of this equipment. It does not override license requirements nor
is it a substitute for a structured operating lesson.
If you are unsure about any aspect of the equipment or its capabilities or if you are in doubt as to its proper usage, feel free to consult our trained
employees for instruction or the answers to any questions you may have regarding the safe operation of this equipment.
www.kennards.com.au