Operation Data

Operation Manual

Jandy

®

Underwater Pool and Spa White Lights

WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a pro fes sion al pool/spa builder or service technician. The procedures in this manual must be followed ex act ly. Failure to follow warning notices and instructions may result in property damage, serious injury, or death. Improper in stal la tion and/or operation will void the war ran ty. Before installing this product, read and follow all warning notices and instructions that accompany this light.

Page 2

Page 3

Table of Contents

Section 1. Safety Information ......................4

Section 2. Operating Instructions ...............5

2.1 To Operate the Light ....................................5

Section 3. Replacing The Lamp ..................5

Section 4. Exploded View and Replacement

Parts.............................................8

4.1 Jandy Pool White Light ................................8

4.2 Jandy Spa White Light .................................9

Figures and Tables

Figure 1. Removing the Pool and Spa White

Light Assembly for Lamp

Replacement ........................................5

Figure 2. Alignment of the Lens, Face Ring,

Housing and Clamps for Pool White

Lights ...................................................7

Figure 3. Jandy Pool White Light Exploded

View .....................................................8

Figure 4. Jandy Pool White Light, Front and

Back View ............................................8

Figure 5. Cross Section of Jandy Pool White

Light .....................................................8

Figure 6. Jandy Spa White Light Exploded

View .....................................................9

Figure 7. Jandy Spa White Light, Front and

Back View ............................................9

Figure 8. Cross Section of Jandy Spa White

Light .....................................................9

Table 1. Lamp Specifications .............................5

Page 4

Section 1.

Safety Information

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF

FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION.

This underwater light must be installed by a licensed or certified electrician in accordance with the National Electrical Code in the US, the Canadian

Electrical Code in Canada, and applicable local codes and ordinances. Improper installation will create an electrical hazard, which could result in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Read and follow the specific instructions below.

WARNING

Before installing this underwater light, read and follow all warning notices and instructions accompanying this light. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage.

Call (707) 776-8200 for additional free copies of these instructions.

CAUTION

Except when the Jandy Pool and Spa lights are installed in an area of the swimming pool that is not used for swimming and the lens is adequately guarded to keep any person from contacting it, the light shall be installed in or on a wall of the pool, with the top of the lens opening not less than 18 inches (457 mm) below the normal water level of the pool

ATTENTION INSTALLER: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.

NOTICE

The Jandy Pool and Spa lights are intended for installation in fresh water and non-fresh water swimming pools and spas. It is important to ensure that the wet niches in which the lights are installed are intended for their appropriate application, either fresh water or non-fresh water.

SAVE THESE INSTRUCTIONS

Section 2. Operating Instructions

2.1 To Operate the Light

Activate the light by either turning on the switch, setting a program, or by pushing the button on a pool and spa controller.

Section 3. Replacing The Lamp

WARNING

Always disconnect power to the pool or spa white light at the circuit breaker before servicing the light.

Failure to do so could result in death or serious injury to installer, serviceman, pool or spa users or others due to electrical shock.

1. Turn off the main electrical switch or circuit breaker, as well as the switch, which operates the underwater light.

Page 5

2. Be sure to have the following items:

• A new lens gasket (P/N R0451101 for Jandy

Pool Light and P/N R0400501 for Jandy Spa

Light).

• One (1) new lamp. See Table 1 for

specifi cations.

WARNING

Replace the lamp with one of the same type and wattage. Failure to replace the lamp with one of the same type will damage the light assembly and may cause an electrical hazard resulting in death or serious injury to pool or spa users, installers, or others due to electrical shock, and may also cause damage to property. Be sure the power is switched

OFF before removing or installing lamps. Allow lamp to cool before replacing.

3. To remove the light assembly, unscrew the special pilot screw at the top of the face ring, remove light assembly from niche and gently place assembly on the deck. It is not necessary to drain down the pool or spa. See Figure 1.

Jandy Model

Fixture

Voltage

Pool/Spa White Light

12 Volt AC

Pool White Light

Pool White Light

Pool White Light

120 Volt AC

12 Volt AC

120 Volt AC

Spa White Light

120 Volt AC

Table 1. Lamp Specifi cations

Lamp

Voltage

12V

120V

12V

120V

120V

Lamp

Wattage

100 Watt

300 Watt

300 Watt

500 Watt

100 Watt

Lamp Type

R20 Flood

R40 Flood

R40 Flood

R40 Flood

R20 Flood

Qty. per

Fixture

1

1

1

1

1

Lamp Kit

Part Number

R0450501

R0450502

R0450503

R0450504

R0450505

Bonding cable

Power

Cord

POOL WHITE LIGHT

ASSEMBLY

Niche

POOL WALL

1

Unscrew pilot screw and pull top of light assembly away from pool wall

PILOT SCREW

2

Push up on bottom of light assembly

Power

Cord

Bonding cable

SPA WHITE LIGHT

ASSEMBLY

Niche

SPA WALL

1

Unscrew pilot screw and pull top of light assembly away from spa wall

PILOT SCREW

2

Push up on bottom of light assembly

POSITIONING TAB

TAB LOCATOR

POSITIONING TAB

TAB LOCATOR

Figure 1. Removing the Pool and Spa White Light Assembly for Lamp Replacement

Page 6

4. Disassemble the light fi xture and replace lamp as follows:

WARNING

Be sure to keep the special pilot screw from this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard, which could result in death or serious injury to pool or spa users, installers or others due to electrical shock.

NOTE A new lens gasket must be used each time the light is reassembled.

WARNING

Risk of Electrical Shock or Electrocution. Always install a new lens gasket whenever disassembling the light (for Jandy Pool Light Gasket P/N

R0451101 and for Jandy Spa Light Gasket P/N

R0400501). Failure to do so may permit water to leak into the assembly, which could cause:

(a) An electrical hazard resulting in death or serious injury to pool or spa users, installers, or others due to electrical shock, or

(b) Breakage of the lamp or lens, which likewise could result in serious injury to pool or spa users, installers, or bystanders, or in damage to property.

f. Tighten the eight (8) Phillips head screws for pool light or the six (6) Phillips head screws for spa light in alternating cross-pattern. Torque screws to approximately 20 in-lbs. Do not over-tighten.

6. Reinstall the Jandy Light into niche fi xture.

Light Gasket

Jandy Spa

Align arrow of the lens with pilot screw

Align pilot screw with arrow located on fixture label

Page 7

Figure 2. Alignment of the Lens, Face Ring, Housing and Clamps for Pool White Lights

WARNING

Use only the special pilot screw provided with this underwater light. This screw mounts and electrically grounds the housing securely to the mounting ring and wet niche. Failure to use the screw provided could create an electrical hazard, which could result in death or serious injury to pool or spa users, installers or others due to electrical shock.

7. If pool or spa is empty, fi ll pool or spa until the underwater light is completely submerged in water before operating the light for more than 10 seconds. Turn on main switch or circuit breaker, as well as the switch, which specifi cally operates the underwater light, to check for proper operation.

WARNING

Never operate this underwater light for more than

10 seconds unless it is totally submerged in water.

Without total submersion, the light assembly will get extremely hot, which may result in serious burns or in breakage of the lamp or lens. This may result in serious injury to pool or spa users, installers, or bystanders or in damage to property.

Page 8

Section 4. Exploded View and Replacement Parts

4.1 Jandy Pool White Light

9

6

9 1

2 3 4 5

8

6

7

8

Figure 3. Jandy Pool White Light Exploded View

7

7

7

7

DWG #

1

5

6

3

4

7

3

3

2

3

8

9

Part #

N/A

N/A

R0450501

R0450502

R0450503

R0450504

R0451101

R0450601

R0450701

R0450801

R0450802

R0450803

R0450804

R0450805

R0450901

R0451001

Description

Pool Light Housing

Lamp Holder

Lamp, 100 Watt, 12 Volt

Lamp, 300 Watt, 120 Volt

Lamp, 300 Watt, 12 Volt

Lamp, 500 Watt, 120 Volt

Silicone Gasket, Pool Light

Glass Lens, Pool Light

Clamp Assembly, Pool Light

Face Ring, Stainless Steel (SS), Pool Light

Face Ring, Plastic, White, Pool Light

Face Ring, Plastic, Black, Pool Light

Face Ring, Plastic, Gray, Pool Light

Face Ring, Plastic Set, Pool Light

Pilot Screw, with Retainer, Pool Light

Clamp Screw (8 Screws and 8 Retainers) Pool Light

Field Replaceable

NO - Purchase New Light

NO - Purchase New Light

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

THICK MOLDED SIDE

OF THE GASKET MUST

MATE WITH THE BODY

OF THE HOUSING

Figure 4. Jandy Pool White Light, Front and Back

View

Figure 5. Cross Section of Jandy Pool White Light

Page 9

4.2 Jandy Spa White Light

9

6

9

1

2

3

4 5

8

6

7

8

Figure 6. Jandy Spa White Light Exploded View

7

7

7

7

8

9

DWG #

1

3

4

2

3

5

6

7

Part #

N/A

N/A

R0450501

R0450505

R0400501

R0400601

R0451201

R0451301

R0451302

R0451303

R0451304

R0451305

R0450901

R0451401

Description

Spa Light Housing

Lamp Holder

Lamp, 100 Watt, 12 Volt

Lamp, 100 Watt, 120 Volt

Silicone Gasket, Spa Light

Glass Lens, Spa Light

Clamp Assembly, Spa Light

Face Ring, Stainless Steel (SS), Spa Light

Face Ring, Plastic, White, Spa Light

Face Ring, Plastic, Black, Spa Light

Face Ring, Plastic, Gray, Spa Light

Face Ring, Plastic Set, Spa Light

Pilot Screw, with O-ring, Spa Light

Clamp Screw (6 Screws and 6 Retainers) Spa Light

Field Replaceable

NO - Purchase New Light

NO - Purchase New Light

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

Figure 7. Jandy Spa White Light, Front and Back

View

Figure 8. Cross Section of Jandy Spa White Light

Page 10

NOTES

NOTES

Page 11

LIMITED WARRANTY

Thank you for purchasing Jandy pool and spa products. Jandy Pool Products, Inc. warrants all parts to be free from manufacturing defects in materials and workmanship for a period of one (1) year from the date of retail purchase, with the following exceptions:

• AquaLink

® RS units installed with Jandy Surge Protection Kits will be covered for two (2) years.

• Never Lube

®

valves are warranted for the life of pool and/or spa on which they were originally installed.

This warranty is limited to the first retail purchaser, is not transferable, and does not apply to products that have been moved from their original installation sites. The liability of Jandy Pool Products, Inc. shall not exceed the repair or replacement of defective parts and does not include any costs for labor to remove and reinstall the defective part, transportation to or from the factory, and any other materials required to make the repair. This warranty does not cover failures or malfunctions resulting from the following:

1. Failure to properly install, operate or maintain the product(s) in accordance with our published Installation,

Operation and Maintenance Manuals provided with the product(s).

2. The workmanship of any installer of the product(s).

3. Not maintaining a proper chemical balance in your pool and/or spa [pH level between 7.2 and 7.8, Total

Alkalinity (TA) between 80 to 120 ppm, Total Dissolved Solids (TDS) less than 2000 not including salt ppm].

4. Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence or acts of God.

5. Scaling, freezing, or other conditions causing inadequate water circulation.

6. Operating the product(s) at water flow rates outside the published minimum and maximum specifications.

7. Use of non-factory authorized parts or accessories in conjunction with the product(s).

8. Chemical contamination of combustion air or improper use of sanitizing chemicals, such as introducing sanitizing chemicals upstream of the heater and cleaner hose or through the skimmer.

9. Overheating; incorrect wire runs; improper electrical supply; collateral damage caused by failure of O-Rings,

DE grids, or cartridge elements; or damage caused by running the pump with insufficient quantities of water.

LIMITATION OF LIABILITY:

This is the only warranty given by Jandy Pool Products, Inc. No one is authorized to make any other warranties on behalf of Jandy Pool Products, Inc. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF FITNESS

FOR A PARTICULAR PURPOSE AND MERCHANTABILITY. JANDY POOL PRODUCTS, INC. EXPRESSLY

DISCLAIM S AND EXCLUDES ANY LIABILIT Y FOR CONSEQUENTIAL , INCIDENTAL, INDIRECT OR

PUNITIVE DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY. This warranty gives you specific legal rights. You may also have other rights that vary by state or province.

WARRANTY CLAIMS:

For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of installation. The installer will contact the factory for instructions regarding the claim and to determine the location of the nearest designated service center. If the dealer is not available, you can locate a service center in your area by visiting www.jandy.com or by calling our technical support department at (707) 776-8200 extension 260. All returned parts must have a Returned Material

Authorization number to be evaluated under the terms of this warranty.

C

ETL LISTED

CONFORMS TO

UL STD 676

Certifi ed to CAN/CSA

C22.2 No. 89

6000 Condor Drive, Moorpark, CA, USA 93021 • 707.776.8200 FAX 707.763.7785

For technical support call 707-776-8200, ext. 260

Litho in U.S.A. © 2007 Jandy Pool Products, Inc. 0712