Panasonic | DS-PAN-103 | Installation instructions | Panasonic DS-PAN-103

8
6
7
5
4
3
2
1
INSTALLATION INSTRUCTIONS:
1. REMOVE THE 1/4-20 X 5/8" BHCS HOLDING THE MOUNTING
BRACKET TO THE REST OF THE DOCKING STATION (THE SCREWS
IN THE PLASTIC SIDE-MEMBERS ON EACH SIDE OF THE DOCK).
PULL MOUNTING BRACKET OFF OF DOCKING STATION.
D
D
2. SET MOUNTING BRACKET ON TOP OF DESIRED SURFACE SO
THAT 3 OF THE HOLES ON THE MOUNTING BRACKET LINE UP WITH
3 TAPPED HOLES OF THE MOTION ACCESSORY. (IF 3 HOLES ARE
NOT AVAILABLE THEN USE 2.) SEE *RECOMMENDED HOLES* OF
THE MOUNTING BRACKET.
3. FASTEN THE MOUNTING BRACKET TO THE MOTION ACCESSORY
USING (3X) 1/4-20 X 5/8" BHCS (OR 2 DEPENDING ON AVAILABILITY).
4. PLACE DOCKING STATION OVER TOP OF MOUNTING BRACKET
SO THAT THE 2 THREADED HOLES IN EACH FLANGE OF THE
MOUNTING BRACKET LINE UP WITH THE 2 HOLES IN EACH PLASTIC
SIDE-MEMBER.
5. FASTEN THE DOCKING STATION BACK TO THE MOUNTING
BRACKET USING (4X) 1/4-20 X 5/8" BHCS.
C
(4X) 1/4-20 X 5/8" BHCS
(120 +/-10% IN-LBS)
C
6. TIGHTEN ALL FASTENERS TO THE INDICATED TORQUE
RECOMMENDATIONS.
(3X) 1/4-20 X 5/8" BHCS
(120 +/-10% IN-LBS)
*USE 3 SCREWS TO FASTEN
DOCK DOWN IF POSSIBLE*
(MOUNTING BRACKET OF
DOCKING STATION)
B
B
*RECOMMENDED HOLES
FOR MOUNTING WITH
2 SCREWS*
HARDWARE KIT CONTENTS:
DATE
PRODUCT I.D.
DS-PAN-101
*RECOMMENDED HOLES
FOR MOUNTING WITH
3 SCREWS*
A
D3-0036-IS-G
(SHEET 1 OF 2)
8
PRODUCT NAME
DS-PAN-101
DOCKING STATION
WARNING: ALL HAVIS INC. PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER, PRODUCT DESCRIPTION
IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING HAVIS INC. MOUNTING AND
DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IS INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
THIS PRODUCT IS USED WITH THE PANASONIC
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
CF-28/29/30 TOUGHBOOK COMPUTERS
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
(THE FEATURES OF THIS PRODUCT MAY BE LIMITED
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
DEPENDING UPON THE MODEL OF COMPUTER USED.)
OPERATING VEHICLE.
DRAWING NUMBER:
7
01-30-07
6
5
4
3
WEIGHT: (LBS)
6.6
REV. DATE
12-07-09
1-800-524-9900
WWW.HAVIS.COM
2
1
F-730-019 REV A
A
8
6
7
5
4
3
2
1
INSTALLATION INSTRUCTIONS:
STRAIN RELIEF
LOCATIONS
NOTE: IT IS VERY IMPORTANT TO STRAIN RELIEF ALL CABLES
CONNECTED TO THE DOCKING STATION.
1. IF IT IS NECESSARY TO STRAIN-RELIEVE WIRES/CABLES, INSERT
ZIP TIE/PUSH PIN FROM HARDWARE KIT INTO ANY OF THE THREE
STRAIN RELIEF HOLES ON THE BOTTOM SIDE OF THE DOCK, AS
SHOWN. LOOP AND TIGHTEN ZIP TIE AROUND WIRES/CABLES, AS
REQUIRED.
D
D
2. IF STRAIN RELIEF MUST BE REMOVED AFTER INSTALLATION,
CUT ZIP TIE PORTION WHERE INDICATED IN ILLUSTRATION A. TO
RE-USE PUSH PIN FOR STRAIN RELIEF, INSERT A ZIP TIE THROUGH
OPENING IN PUSH PIN AND LOOP AROUND WIRES/CABLES, AS
REQUIRED.
NOTE: IF ORDERING AN EXTRA SET OF KEYS, REFER TO THE KEY
CODE NUMBER STAMPED ON THE KEYS. IF KEYS ARE NOT
AVAILABLE, PLEASE HAVE SERIAL NUMBER OF DOCK AVAILABLE
BEFORE CONTACTING HAVIS.
C
B
C
ZIP TIE/PUSH PIN
*ADDITIONAL MOUNTING COMPONENT,
MOTION DEVICE, OR TUBE (NOT SHOWN)
IS MOUNTED ON THIS SURFACE*
B
CUT HERE TO
REMOVE ZIP TIE
DATE
PRODUCT I.D.
DS-PAN-101
ILLUSTRATION A
PRODUCT NAME
DS-PAN-101
DOCKING STATION
A
WARNING: ALL HAVIS INC. PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER, PRODUCT DESCRIPTION
IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING HAVIS INC. MOUNTING AND
DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IS INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
THIS PRODUCT IS USED WITH THE PANASONIC
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
CF-28/29/30 TOUGHBOOK COMPUTERS.
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
(THE FEATURES OF THIS PRODUCT MAY BE LIMITED
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
OPERATING VEHICLE.
DEPENDING UPON THE MODEL OF COMPUTER USED.)
DRAWING NUMBER:
D3-0036-IS-G
(SHEET 2 OF 2)
8
7
6
5
4
01-30-07
3
WEIGHT: (LBS)
6.6
REV. DATE
12-07-09
1-800-524-9900
WWW.HAVIS.COM
2
1
F-730-019 REV A
A
Download PDF

advertising