Panasonic TH-65PB1U touch screen monitor Operating instructions

Document
Model No.
TH-65PB1U
Operating Instructions
Display Operations
Interactive Plasma Display
English
Before connecting, operating or adjusting this product,
please read these instructions completely.
Please keep this manual for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualied service personnel.
The lightning flash with
arrow-head within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock
to persons.
The exclamation point within
a triangle is intended to
tell the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING : To prevent damage which may result in re or shock hazard, do not expose this apparatus to rain
or moisture.
Do not place containers with water (ower vase, cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualied service personnel.
2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only t a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
2
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments / accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
3
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment
from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making any adjustments,
and retain them for future reference.
Retain your purchase receipt as well, and record the model number and serial number of your set in the
space provided on the rear cover of these instructions.
Visit our Panasonic Web Site
http://panasonic.net
Table of Contents
Important Safety Instructions.................................. 3
FCC STATEMENT ...................................................... 5
Safety Precautions ................................................... 6
Maintenance .............................................................. 7
3D Safety Precautions ............................................. 8
Accessories ............................................................ 10
Accessories Supplied ............................................ 10
Remote Control Batteries ...................................... 10
Connections ............................................................ 11
Speaker connection ................................................11
AC cord connection and xing, cable xing ............11
Video equipment connection ................................. 12
VIDEO and COMPONENT / RGB IN connection .... 12
HDMI connection ................................................... 13
DVI-D IN connection .............................................. 13
PC Input Terminals connection .............................. 14
SERIAL Terminals connection ............................... 15
Power ON / OFF ...................................................... 16
Selecting the input signal ...................................... 18
Basic Controls ........................................................ 19
ASPECT Controls ................................................... 21
Digital Zoom ............................................................ 22
Viewing 3D images ................................................. 23
To view the 3D images .......................................... 23
Troubleshooting for 3D Eyewear .......................... 24
Table of images that can be seen for each 3D
Picture Format and the source image format ........ 24
On-Screen Menu Displays ..................................... 25
Adjusting POS./SIZE .............................................. 26
PICTURE Adjustments ........................................... 29
ADVANCED SETTINGS ........................................ 30
Picture Proles ....................................................... 31
Saving proles ....................................................... 32
Loading proles ..................................................... 33
Editing proles ....................................................... 33
SOUND Adjustment ................................................ 34
SDI SOUND OUTPUT ........................................... 34
SETUP menu ........................................................... 35
4
DAY/TIME SETUP / ON/OFF TIMER SETUP .......... 36
DAY/TIME SETUP ................................................. 36
ON/OFF TIMER SETUP ........................................ 36
TOUCH-PEN MODE ................................................ 37
3D SETTINGS .......................................................... 38
SCREENSAVER (For preventing image
retention) ................................................................. 39
Setup of SCREENSAVER Time ............................ 40
Reduces screen image retention .......................... 41
EXTENDED LIFE SETTINGS ............................... 41
ECO MODE SETTINGS ........................................... 44
Customizing the Input labels................................. 45
FUNCTION BUTTON SETTINGS ............................ 46
NO ACTIVITY POWER OFF .................................... 47
MENU DISPLAY DURATION / OSD
BRIGHTNESS .......................................................... 47
OSD LANGUAGE .................................................... 47
DISPLAY ORIENTATION ......................................... 47
SETUP for MULTI DISPLAY .................................... 48
How to setup MULTI DISPLAY .............................. 48
ID Remote Control Function .................................. 49
SETUP for PORTRAIT ............................................ 50
How to setup PORTRAIT ...................................... 50
SETUP for Input Signals ........................................ 52
COMPONENT / RGB IN SELECT ......................... 52
YUV / RGB IN SELECT ......................................... 52
SIGNAL menu ....................................................... 53
Options Adjustments ............................................. 56
3D Safety Precautions (To hide 3D Safety
Precautions) .......................................................... 59
Weekly Command Timer ....................................... 59
Audio input select .................................................. 61
Input Search .......................................................... 62
Troubleshooting ..................................................... 63
List of Aspect Modes ............................................. 64
Applicable Input Signals ........................................ 65
Shipping condition ................................................. 66
Command list of Weekly Command Timer ........... 67
Specications ......................................................... 68
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC CAUTION:
To assure continued compliance, follow the attached installation instructions and use only shielded interface
cables when connecting to computer or peripheral devices. Any changes or modications not expressly
approved by Panasonic Corp. of North America could void the user's authority to operate this device.
FCC Declaration of Conformity
Model No. TH-65PB1U
Responsible Party:
Contact Source:
Panasonic Corporation of North America
Three Panasonic Way 2F-5, Secaucus, NJ 07094
Panasonic System Communications Company of North America
1-800-973-4390
CANADIAN NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to
remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
• HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
• “RealD 3D” is a trademark of RealD.
5
Safety Precautions
CAUTION
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Pedestal ..................................................... TY-ST65P20
• Mobile Stand for Display ............................ TY-ST65PF1
• Wall-hanging bracket (angled) ................... TY-WK65PR20
• BNC Dual Video Terminal Board ................ TY-FB9BD
• HD-SDI Terminal Board.............................. TY-FB9HD
• HD-SDI Terminal Board with audio ............ TY-FB10HD
• Dual Link HD-SDI Terminal Board.............. TY-FB11DHD
• Dual HDMI Terminal Board ........................ TY-FB10HMD
• DVI-D Terminal Board ................................ TY-FB11DD
• Mate-IF Boad ............................................. TY-FB11HB
• AV Terminal Box ......................................... TY-TB10AV
• 3D IR TRANSMITTER ............................... TY-3D30TRW
• 3D Eyewear................................................ TY-EW3D3SU, TY-EW3D3MU, TY-EW3D3LU
• Electronic Pen for Interactive Plasma Display... TY-TPEN1PBU
• Wireless Module......................................... ET-WM200U
Always be sure to ask a qualied technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being
played with by young children, creating the potential risk of suffocation.
When using the Plasma Display
Do not bring your hands, face or objects close to the
ventilation holes of the Plasma Display.
• Top of the Plasma Display is usually very hot due to the
high temperature of exhaust air being released through the
ventilation holes. Burns or personal injuries can happen if any
body parts are brought too close. Placing any object near the
top of the display could also result in heat damages to the object
as well as to the Display if its ventilation holes are blocked.
Be sure to disconnect all cables before moving the Plasma Display.
• Moving the Display with its cables attached might damage
the cables which, in turn, can cause re or electric shock.
Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
• Electric shocks can result if this is not done.
6
Clean the power cable regularly to prevent it from
becoming dusty.
• Built-up dust on the power cord plug can increase humidity
which might damage the insulation and cause re. Unplug
the cord from the wall outlet and clean it with a dry cloth.
This Plasma Display radiates infrared rays, therefore it
may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct
or reected light from your Plasma Display.
Note:
Do not allow a still picture to be displayed for an extended
period, as this can cause a permanent image retention to
remain on the Plasma Display.
Examples of still pictures include logos, video games, computer
images, teletext and images displayed in 4:3 mode.
Safety Precautions
WARNING
Setup
Do not place the Plasma Display on sloped or unstable
surfaces, and ensure that the Plasma Display does not
hang over the edge of the base.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water spills onto the Plasma Display or foreign objects get
inside it, a short-circuit may occur which could result in re or
electric shock. If any foreign objects get inside the Plasma
Display, please consult an Authorized Service Center.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat,
which can cause re or damage to the Plasma Display.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or
downward may cause damage to the internal circuitry.
If using the pedestal (optional accessory), leave a space
of 3 15/16” (10 cm) or more at the top, left and right, and
2 3/4” (7 cm) or more at the rear, and also keep the space
between the bottom of the display and the oor surface.
If using some other setting-up method, follow the manual
of it. (If there is no specic indication of installation
dimension in the installation manual, leave a space of
3 15/16” (10 cm) or more at the top, bottom, left and right,
and 2 3/4” (7 cm) or more at the rear.)
When installing the Plasma Display vertically;
Turn up the power switch for the upward direction when you
install the Plasma Display vertically.
And set “DISPLAY ORIENTATION” to “PORTRAIT” in
SETUP menu. (see page 47)
An apparatus with CLASS I construction shall be
connected to a mains socket outlet with a protective
earthing connection.
AC Power Supply Cord
The Plasma Display is designed to operate on 110 - 127
V AC, 50/60 Hz.
Ensure that the mains plug is easily accessible.
Do not use any power supply cord other than that
provided with this unit.
• Doing so may cause re or electric shocks.
Securely insert the power cord plug as far as it will go.
• If the plug is not fully inserted, heat may be generated
which could cause re. If the plug is damaged or the
wall socket plate is loose, they should not be used.
Do not handle the power cord plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that might damage the power cable. When
disconnecting the power cable, hold the plug, not the cable.
• Do not make any modications, place heavy objects on,
place near hot objects, heat, bend, twist or forcefully
pull the power cable. Doing so may cause damage to
the power cable which can cause re or electric shock.
If damage to the cable is suspected, have it repaired at
an Authorized Service Center.
If the Plasma Display will not be used for a long period
of time, unplug the power cord from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound),
or if smoke or an abnormal odor is detected from the
Plasma Display, unplug the power cord immediately.
• Continuous use of the Display under these conditions
might cause re or permanent damage to the unit.
Have the Display evaluated at an Authorized Service
Center. Services to the Display by any unauthorized
personnel are strongly discouraged due to its high
voltage dangerous nature.
If water or foreign objects get inside the Plasma Display,
if the Plasma Display is dropped, or if the cabinet
becomes damaged, disconnect the power cord plug
immediately.
• A short may occur, which could cause re. Contact an
Authorized Service Center for any repairs that need to
be made.
Maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which
neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface
is dry.
• Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may become
damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise
the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added
and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact
with articles made from rubber or PVC.
7
Safety Precautions
3D Safety Precautions
WARNING
Small Parts
3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small
children to avoid accidental ingestion.
Disassembly
Do not disassemble or modify the 3D Eyewear.
CAUTION
To enjoy 3D images safely and comfortably, please read these instructions fully.
Use for commercial applications and public viewing
Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.
3D Eyewear (sold separately)
Do not drop, exert pressure on, or step on the 3D Eyewear.
Be careful of the tips of the frame when putting on the 3D Eyewear.
Be careful not to trap a nger in the hinge section of the 3D Eyewear.
Pay special attention when children are using the 3D Eyewear.
3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline.
All children must be fully supervised by parents or guardians who must ensure their safety and health throughout
the using 3D Eyewear.
8
Safety Precautions
Viewing 3D Content
Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc.
When preparing your own 3D content, ensure that it is properly produced.
Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other
existing medical conditions.
Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other
uncomfortable sensation.
Take an appropriate break after viewing a 3D movie.
Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games or
computers.
Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance
between the user and screen can be misjudged.
The 3D Eyewear must only be worn when viewing 3D content.
If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off
automatically.
If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and right),
please ensure to correct your vision before using the 3D Eyewear.
Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content.
Do not use the 3D Eyewear at a distance less than the recommended distance.
View from at least the recommended distance (3 times the effective height of the screen).
Recommended distance: 94.5”/2.4 m
When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance
3 times further than the height of the actual image. (That makes the distance closer than above recommended
gure.)
3D Eyewear (sold separately) Use
Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental damage
or injury.
Remove the 3D Eyewear before moving around to avoid falling or accidental injury.
Use the 3D Eyewear only for the intended purpose and nothing else.
Do not use 3D Eyewear in the condition of high temperature.
Do not use if the 3D Eyewear is physically damaged.
Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear
false operations.
Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves
near the 3D Eyewear as this may cause the 3D Eyewear to malfunction.
Stop using the 3D Eyewear immediately if a malfunction or fault occurs.
Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose
or temples.
In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction.
9
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Operating
Instruction book
Software DVD-ROM &times; 1
Remote Control Transmitter
N2QAYB000691
• elite Panaboard software
• elite Panaboard book
• Operating Instructions
Display Operations
Network Operations
Electronic Pen Operations
• Software license statements
GNU GENERAL PUBLIC LICENSE
GNU LESSER GENERAL PUBLIC LICENSE
Clamper &times; 1
TMME289
Ferrite core &times; 2
J0KG00000014
AC cord
Batteries for the
Remote Control
Transmitter
(AA Size &times; 2)
Electronic Pen set
Refer to “Operating Instructions,
Electronic Pen Operations”.
Use the Ferrite cores to comply with the EMC standard.
(refer to “Operating Instructions, Network Operations”)
Remote Control Batteries
Requires two AA batteries.
1. Pull and hold the hook, then
open the battery cover.
2. Insert batteries - note correct
polarity (+ and -).
3. Replace the cover.
“AA” size
+
+
-
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precautions:
1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.
6. Do not burn or breakup batteries.
7. Batteries must not be exposed to excessive heat such as sunshine, re or the like.
10
Connections
Speaker connection
Note:
Please use 8 /10 W speaker.
2
1
Red
Red
Black
Black
While pressing the lever,
insert the core wire.
Return the lever.
AC cord connection and xing, cable xing
AC cord xing
Unplug the AC cord
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on
both the left and right sides.
Using the clamper
Secure any excess cables with clamper as required.
Unplug the AC cord pressing the
two knobs.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet rst.
Note:
One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately.
1 Attach the clamper
To remove from the unit:
2 Bundle the cables
To loosen:
hole
snaps
Insert the clamper
in a hole.
Keep
pushing both
side snaps
hooks
Set the
tip in the
hooks
knob
Keep
pushing
the knob
11
Connections
Video equipment connection
Terminals are on the bottom side of the Plasma Display.
SERIAL:
Control the Plasma Display
by connecting to PC.
(see page 15)
3D IR TRANSMITTER:
Connect the 3D IR
TRANSMITTER (optional
accessory).
(8Ω,20W[10W+10W])
SLOT: Terminal board (optional
accessories) insert slot
(see page 6)
Note:
The right side slot is for terminal board
with 2-slot width. The terminal board
with 1-slot width does not function when
installed in the right side slot.
AV IN (VIDEO): Composite Video Input Terminal
(see below)
COMPONENT/RGB IN: Component/RGB Video Input
Terminal (see below)
DVI-D IN: DVI-D Input Terminal (see page 13)
PC IN: PC Input Terminal Connect to video terminal of
PC or equipment with Y, PB(CB) and PR(CR) output.
(see page 14)
AV IN (HDMI):
HDMI Input Terminal
(see page 13)
Connect to video equipment
such as VCR or DVD player.
WIRELESS
MODULE, LAN:
Refer to “Operating
Instructions, Network
Operations”.
VIDEO and COMPONENT / RGB IN connection
Note:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
VIDEO
OUT
L
RCA-BNC
Adapter plug
R
AUDIO
OUT
VCR
AUDIO L-R: Shared with VIDEO and
COMPONENT/RGB IN
(8Ω,20W[10W+10W])
Notes:
• Change the “COMPONENT/RGB-IN select” setting in the “SETUP”
menu to “COMPONENT” (when COMPONENT signal connection)
or “RGB” (when RGB signal connection). (see page 52)
• Signals input to COMPONENT/RGB IN terminals correspond to
SYNC ON G or SYNC ON Y.
L
R
RCA-BNC
Adapter plug
Computer
Y
PB
PR
12
DVD Player
AUDIO
OUT
Y, PB, PR,
OUT
RGB Camcorder
Connections
HDMI connection
[Pin assignments and signal names]
Pin No.
1
2
3
4
5
6
7
8
9
10
Signal Name
Pin No.
11
T.M.D.S Data2+
T.M.D.S Data2
Shield
T.M.D.S Data2T.M.D.S Data1+
T.M.D.S Data1
Shield
T.M.D.S Data1T.M.D.S Data0+
T.M.D.S Data0
Shield
T.M.D.S Data0T.M.D.S Clock+
(8Ω,20W[10W+10W])
Signal Name
T.M.D.S Clock
Shield
12
T.M.D.S Clock-
13
CEC
14
Reserved
(N.C. on device)
15
16
17
18
19
SCL
SDA
DDC/CEC
Ground
+5V Power
Hot Plug Detect
HDMI cable
3 1
19
4 2
18
HDMI
AV OUT
DVD player
Note:
Additional equipment and HDMI cable shown are not supplied with this set.
DVI-D IN connection
Shared with PC IN.
(8Ω,20W[10W+10W])
PC with DVI-D
video out
Stereo mini plug (M3)
DVI-video cable (Within 5 m)
DVI-D Input Connector
Pin Layouts
1
Pin No.
8
9
16
17
24
Connection port view
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
T.M.D.S. data 2T.M.D.S. data 2+
T.M.D.S. data 2 shield
DDC clock
DDC data
T.M.D.S. data 1T.M.D.S. data 1+
T.M.D.S. data 1 shield
Pin No.
13
14
15
16
17
18
19
20
21
22
23
24
Signal Name
+5 V DC
Ground
Hot plug detect
T.M.D.S. data 0T.M.D.S. data 0+
T.M.D.S. data 0 shield
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock-
Notes:
• Additional equipment and cables shown are not supplied with this set.
• Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or
the quality of the cable.
13
Connections
PC Input Terminals connection
Shared with DVI-D IN.
(8Ω,20W[10W+10W])
COMPUTER
Conversion adapter
(if necessary)
(Female)
Mini D-sub 15p
RGB
PC cable
(Male)
Audio
Stereo mini plug (M3)
Connect a cable which matches
the audio output terminal on the computer.
Notes:
• With regard to the typical PC input signals that are described in the applicable input signals list (see page 65), adjustment
values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight
PC input signal types that are not included in the list.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 &times; 1,080 dots when the aspect mode is set to “4:3”, and 1,920 &times; 1,080
dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible
to show ne detail with sufcient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need
to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specied
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• Change the “COMPONENT/RGB-IN SELECT” setting in the “SETUP” menu to “COMPONENT”
(when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 52)
Signal Names for Mini D-sub 15P Connector
Pin No.
5
4
10 9
3
2
8
1
7
1
6
15 14 13 12 11
Pin Layout for PC Input
Terminal
14
2
3
4
5
Signal Name
R (PR/CR)
G (Y)
B (PB/CB)
NC (not connected)
GND (Ground)
Pin No.
6
7
8
9
10
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
Pin No.
11
12
13
14
15
Signal Name
NC (not connected)
SDA
HD/SYNC
VD
SCL
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Note: To use serial control for this unit, make sure to set the “CONTROL I/F SELECT” in the “NETWORK SETUP” menu
to “RS-232C”. (refer to “Operating Instructions, Network Operations”)
(Male)
COMPUTER
(8Ω,20W[10W+10W])
9
5
RS-232C Straight cable (Female)
8
4
7
3
6
2
1
Pin layout for SERIAL Terminal
D-sub 9p
Notes:
• Use the RS-232C straight cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface
specication, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the sending
and receiving of control data which satises the conditions
given below. Use a computer application such as programming
language software. Refer to the documentation for the
computer application for details.
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
Basic format for control data
The transmission of control data from the computer starts with
a STX signal, followed by the command, the parameters, and
lastly an ETX signal in that order. If there are no parameters,
then the parameter signal does not need to be sent.
STX
C1 C2 C3
Start
(02h)
:
2
3
5
4 • 6
7
8
1 • 9
Communication parameters
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
Signal names for D-sub 9P connector
Details
Pin No.
P1 P2 P3 P4 P5
ETX
Colon
Parameter(s)
(1 - 5 bytes)
3-character
command (3 bytes)
End
(03h)
Notes:
• If multiple commands are transmitted, be sure to wait for
the response for the rst command to come from this unit
before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
• S1A and S1B of Command IMS are available only when a
dual input terminal board is attached.
• Consult an Authorized Service Center for detail instructions
on command usage.
RXD
TXD
GND
Non use
(Shorted in this set)
NC
These signal names are those of computer specications.
Command
Command Parameter
Control details
PON
None
Power ON
POF
None
Power OFF
AVL
**
Volume 00 - 63
AMT
0
Audio MUTE OFF
1
Audio MUTE ON
Input select (toggle)
IMS
None
SLOT input (SLOT INPUT)
SL1
SLOT input (SLOT INPUT A)
S1A
SLOT input (SLOT INPUT B)
S1B
VIDEO input (VIDEO)
VD1
COMPONENT/RGB IN input
YP1
(COMPONENT)
HDMI input (HDMI)
HM1
DVI-D IN input (DVI)
DV1
PC IN input (PC)
PC1
Network input (NETWORK)
NW1
DAM
None
Screen mode select (toggle)
ZOOM (For Video/SD/PC signal)
ZOOM
FULL
FULL
JUST (For Video/SD signal)
JUST
4:3 (For Video/SD/PC signal)
NORM
JUST (For HD signal)
SJST
4:3 (For HD signal)
SNOM
H-FILL (For HD signal)
SFUL
ZOM2
ZOOM (For HD signal)
With the power off, this display responds to PON command only.
15
Power ON / OFF
Connecting the AC cord plug to the Plasma Display.
Connecting the plug to the Wall Outlet.
Note:
When disconnecting the AC cord, be absolutely sure to
disconnect the AC cord plug at the socket outlet rst.
INPUT
Press the Power switch on the Plasma Display to turn the
set on: Power-On.
MENU
-/
VOL
+/
ENTER/
Power Indicator
Power Indicator: Green
[Starting up the network]
It takes some time for the network to start up just after the
power is turned on.
During that time, “NETWORK SETUP” in the “SETUP” menu
is grayed out and cannot be set.
Press the
Remote Control Sensor
button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
when the Plasma Display is on or in standby mode.
switch on the unit,
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
16
Power ON / OFF
When rst switching on the unit
Following screen will be displayed when the unit is turned on for the rst time.
Select the items with the remote control. Unit buttons are invalid.
OSD LANGUAGE
OSD LANGUAGE
DAY/TIME SETUP
DISPLAY ORIENTATION
DISPLAY ORIENTATION
DAY/TIME SETUP
English (UK)
TIME
Deutsch
MON 99:99
SET
Fran&ccedil;ais
MON
99:99
DAY
TIME
Italiano
LANDSCAPE
PORTRAIT
Espa&ntilde;ol
ENGLISH (US)
DAY/TIME SETUP
TIME
SELECT
MON 99:99
SET
SET
TUE
10:00
DAY
TIME
Select the
language.
2 Set.
1
1
Select “DAY” or “TIME”.
2
Setup “DAY” or “TIME”.
1
Select “SET”.
2
Set.
For vertical installation,
select “PORTRAIT”.
2 Set.
1
Notes:
• Once the items are set, the screens won't be displayed when switching on the unit next time.
• After the setting, the items can be changed in the following menus.
OSD LANGUAGE (see page 47)
DAY/TIME SETUP (see page 36)
DISPLAY ORIENTATION (see page 47)
Power ON warning message
The following message may be displayed when turning the unit power ON:
3D Safety Precautions
When 3D images will be viewed by unspecied number of
people or used for commercial applications, someone in
authority should convey the following precautions.
These precautions should be followed in the home as well.
To enjoy 3D images safely and comfortably, please refer
to the Operating Instructions for in-depth description.
Please refrain from viewing 3D images if you do not
feel well or are experiencing visual fatigue.
Activate 3D Safety Precautions if you deliver 3D images to unspecied audiences for business or other purposes.
If “3D FUNCTION” in “3D SETTINGS” is set to “ON”, a warning message is displayed every time the power is
turned ON. (see page 38)
No activity power off Precautions
’NO ACTIVITY POWER OFF’ IS ENABLED.
If “NO ACTIVITY POWER OFF” in SETUP menu is set to “ENABLE”, a warning message is displayed every time
the power is turned ON. (see page 47)
These message displays can be set with the following menu: Options menu
3D Safety Precautions (see page 59)
Power On Message (see page 58)
17
Selecting the input signal
Press to select the input signal to be played back from the equipment which has
been connected to the Plasma Display.
Input signals will change as follows:
PC
NETWORK
VIDEO
COMPONENT*
HDMI
DVI
PC: PC input terminal in PC IN.
NETWORK: Network input terminal in LAN or WIRELESS MODULE.
VIDEO: Video input terminal in AV IN (VIDEO).
COMPONENT*: Component or RGB input terminal in COMPONENT/RGB IN.
HDMI: HDMI input terminal in AV IN (HDMI).
DVI: DVI input terminal in DVI-D IN.
* “COMPONENT” may be displayed as “RGB” depending on the setting of
“COMPONENT/RGB-IN SELECT”. (see page 52)
When an optional Terminal Board is installed:
PC
NETWORK
SLOT INPUT
VIDEO
INPUT
COMPONENT
HDMI
MENU
-/
VOL
+/
ENTER/
DVI
SLOT INPUT: Input terminal in Terminal Board
Note:
When a Terminal Board incompatible with the Plasma Display is installed,
“NON-COMPATIBLE FUNCTION BOARD” is displayed.
INPUT
MENU
-/
VOL
+/
ENTER/
When a Terminal Board with dual input terminals is installed:
PC
NETWORK
SLOT INPUT A
SLOT INPUT B
VIDEO
COMPONENT
HDMI
DVI
SLOT INPUT A, SLOT INPUT B: Dual input terminal in Terminal Board.
Notes:
• Selecting is also possible by pressing the INPUT button on the unit.
• Outputs the sound as set in “Audio input select” in the Options menu.(see page 61)
• Select to match the signals from the source connected to the component/RGB input terminals. (see page 52)
• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an
extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 63), but
this function is not the perfect solution to image retention.
18
Basic Controls
Main Unit
Remote control sensor
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is
displayed:
“+” : press to move the cursor up
“–” : press to move the cursor down
(see page 25)
INPUT
MENU
-/
Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will
still consume some power as long as the
power cord is still inserted into the wall
outlet.)
• Standby ........ Red
Orange (When “Slot power” is set to
“On”. See page 58)
Orange (Depending on the type of
the function board installed, when the
power is supplied to the slot)
Orange (When “CONTROL I/F
SELECT” is set to “LAN” or “WEB
CONTROL” is set to “ON”. Refer
to “Operating Instructions, Network
Operations”.)
• Power-ON ...... Green
• PC POWER MANAGEMENT (DPMS)
....................... Orange (With PC input signal.
See page 44)
• DVI-D POWER MANAGEMENT
.......................Orange (With DVI input signal.
See page 44)
VOL
+/
ENTER/
Enter / Aspect button
(see page 21, 25)
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen
will switch. (see page 25)
Normal Viewing
SOUND
PICTURE
POS./SIZE
SETUP
INPUT button (Input signal selection)
(see page 18)
19
Basic Controls
Remote Control Transmitter
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect.
(see page 21)
Standby (ON / OFF) button
The Plasma Display must rst be plugged
into the wall outlet and turned on at the
power switch (see page 16).
Press this button to turn the Plasma Display
On, from Standby mode. Press it again
to turn the Plasma Display Off to Standby
mode.
POS. /SIZE button
(see page 26)
PICTURE button
(see page 29)
Sound mute On / Off
Press this button to mute the sound.
Press again to reactivate sound.
Sound is also reactivated when power is
turned off or volume level is changed.
N button
(see page 28, 29, 30, 34)
POSITION buttons
INPUT button
Press to select input signal sequentially.
(see page 18)
ECO MODE (ECO)
Press to change the ECO MODE
setup status. (see page 44)
FUNCTION buttons (FUNCTION)
(see page 46)
OFF TIMER button
The Plasma Display can be preset to switch to standby after a xed period. The setting changes to 30
minutes, 60 minutes, 90 minutes and 0 minutes (off
timer cancelled) each time the button is pressed.
30 MIN
60 MIN
90 MIN
0 MIN(Cancel)
When three minutes remain, “OFF TIMER 3 MIN”
will ash.
The off timer is cancelled if a power interruption
occurs.
AUTO SETUP button
Automatically adjusts the position/
size of the screen. (see page 26)
SETUP button (see page 35)
SOUND button (see page 34)
Volume Adjustment
Press the Volume Up “+” or Down “–”
button to increase or decrease the
sound volume level.
R button (see page 25)
Press the R button to return to
previous menu screen.
RECALL button
Press the “RECALL” button to
display the current system status.
1 Input label
2 Aspect mode (see page 21)
During 3D images (see page 38)
Audio input (see page 61)
Prole name (see page 33)
NANODRIFT SAVER operating
(see page 42)
3 Touch Pen mode ON/OFF
(see page 37)
4 Off timer
The off timer indicator is
displayed only when the off
timer has been set.
5 Clock display (see page 58)
PC
1
4:3
3D
COMPONENT
2
MEMORY NAME: MEMORY2
NANODRIFT
5
TOUCH-PEN ON
3
OFF TIMER 90MIN
4
10:00
Digital Zoom (see page 22)
20
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format
picture.
Note:
Be aware that if you put the display in a public place for commercial purposes or a public showing and
then use the aspect mode select function to shrink or expand the picture, you may be violating the
copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people
for commercial purposes without the prior permission of the copyright holder.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 64).
[from the unit]
INPUT
MENU
-/
VOL
+/
ENTER/
The aspect mode changes each time the ENTER button is pressed.
For VIDEO (S VIDEO) signal input:
4:3
ZOOM
For PC signal input:
4:3
ZOOM
FULL
FULL
JUST
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
ZOOM
FULL
JUST
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
FULL
JUST
4:3
H-FILL
ZOOM
[For 3D images or Touch Pen mode]
The aspect is xed as “FULL” and you cannot switch.
Notes:
• The aspect mode is memorized separately for each input terminal.
• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image
retention to remain on the Plasma Display Panel.
All Aspect mode
Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 58). When All Aspect mode, the aspect
mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes” (page 64).
For VIDEO (S VIDEO) signal input:
4:3
Zoom1
Zoom2
Zoom3
For PC signal input:
4:3
Zoom
16:9
14:9
Just
16:9
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
Zoom1
Zoom2
Zoom3
16:9
14:9
Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
4:3 Full
Zoom1
Zoom2
Zoom3
16:9
14:9
Just1
Just2
4:3 (1)
4:3 (2)
21
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
1
Display the operation guide.
EXIT
Press to access Digital Zoom.
The operation guide will be displayed.
1
During Digital Zoom, only the following buttons can be operated.
[Remote control]
OFF TIMER button
[Unit]
INPUT
MENU
-/
VOL
+/
ENTER/
VOL button
MUTE button
VOL button
POSITION /
ACTION button
2
Select the area of the image to be enlarged.
Press on the enlargement location to select.
The cursor will move.
EXIT
2
3
Select the magnication required for the enlarged display.
Each time this is pressed, the magnication factor changes.
This is shown in the image being displayed.
s1
4
s2
Return to normal display (quit Digital Zoom).
Press to exit from the Digital Zoom.
Notes:
• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
• The Digital Zoom function cannot be selected while in the following operation state:
During Touch Pen mode (see page 37).
During 3D image (see page 38).
When MULTI DISPLAY SETUP is ON (see page 48).
When PORTRAIT SETUP is ON (see page 50).
When SCREENSAVER (except for NEGATIVE IMAGE) is running. (see page 39)
• While Digital Zoom is in operation, “Adjusting POS./SIZE” cannot be used.
22
s3
s4
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear
(optional).
Note:
You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display.
For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear.
This display supports “Frame Sequential*1”, “SIDE BY SIDE*2” and “TOP AND BOTTOM*3” 3D formats.
*1: The 3D format that the images for the left and right eyes are recorded with the high denition quality and alternately played back
*2, *3: See “Table of images that can be seen for each 3D Picture Format and the source image format” on page 24.
To view the 3D images
To view the contents of the Frame Sequential format (ex. 3D-compatible Blu-ray Disc, etc.) with 3D effect
Connect the 3D-compatible player via an HDMI cable (see page 10) and playback the contents.
• Use fully wired HDMI compliant cable.
• For the settings of the player, read the manual of the player.
• If you use the non 3D-compatible player, the images will be displayed without 3D effect.
To view the contents of 3D formats other than Frame Sequential with 3D effect.
Match the picture format in “3D INPUT FORMAT” (see page 38) before viewing.
• You can view “SIDE BY SIDE” and “TOP AND BOTTOM” with 3D effect even if you use the non 3D-compatible player.
• Please consult the suppliers of contents or programmes for availability of this service.
Turn the 3D Eyewear on
• See the instruction manual of 3D eyewear for handling.
Put on the 3D Eyewear
Watch the 3D images
Notes:
• If the room is lit by uorescent lights and light appears to icker when using the 3D Eyewear, switch off the uorescent
light. Alternatively, please set “3D REFRESH RATE” to “100Hz” or “120Hz” whichever reduces icker. (see page 54)
• 3D content will not be correctly visible if the 3D Eyewear is worn upside down or back-to-front.
• Do not wear the 3D Eyewear when watching anything other than 3D images. Liquid crystal displays (such as computer
screens, digital clocks or calculators, etc.) may be difcult to see while wearing the 3D Eyewear.
• Do not use the 3D Eyewear as sunglasses.
• 3D effects may be perceived differently depending on the person.
23
Viewing 3D images
Troubleshooting for 3D Eyewear
Symptoms
Checks
Cannot see 3D images
There is something wrong with the 3D
images
• Has the 3D Eyewear been switched On?
• Ensure that “3D FUNCTION” in “3D SETTINGS” is set to “ON”. (see
page 38)
• Some 3D image signals may not be automatically recognized as 3D
images. Set “3D INPUT FORMAT” in “3D SETTINGS” to match the
picture format. (see page 38)
• Check if 3D IR TRANSMITTER is turned on and corrected properly.
• Check that there are no obstacles between the 3D IR TRANSMITTER
and the 3D Eyewear. If the 3D Eyewear stops receiving the infrared
signal for about 5 minutes, the 3D Eyewear will be turned off
automatically.
• Check the available area to use the 3D Eyewear.
• Depending on the person, the 3D images may be difcult to see, or
cannot be seen, especially in users that have a different level of eyesight
between the left and right eyes.
Take the necessary steps (wearing glasses etc.) to correct your eyesight
before use.
• Check that there are no obstacles between the 3D IR TRANSMITTER
and the 3D Eyewear or that the 3D Eyewear is placed inside the
coverage area. If the 3D Eyewear stops receiving the infrared signal for
about 5 minutes, the 3D Eyewear will be turned off automatically.
• Switch “SWAPPED” and “NORMAL” under “LEFT/RIGHT SWAP” in “3D
SETTINGS” (see page 38).
Indicator lamp will not light when the 3D
glasses are turned ON.
• The battery may be running low or at. Change the battery or charge the
3D glasses.
3D Eyewear is turned off automatically
Table of images that can be seen for each 3D Picture
Format and the source image format
If the picture appears to be abnormal, refer to the table below to choose the correct 3D picture format setting.
3D INPUT FORMAT
Source image
format
AUTO
SIDE BY SIDE
*1
Normal*2
TOP AND BOTTOM
NATIVE
Side by side
Top and bottom
*1
Normal*2
Normal format
(2D)
Normal
*1
Normal
When the source image is not recognized correctly
*2
When “3D FUNCTION” is set to “ON”, the images will be displayed with 3D effect. When set to “OFF”, displayed
without 3D effect.
• Depending on the player or contents, the image may be different from the above illustrations.
24
On-Screen Menu Displays
Remote Control
1 Display the menu screen.
Unit
Press several times.
MENU
Press to select.
(Example: PICTURE menu)
2 Select the item.
Each time the MENU button is pressed, the
menu screen will switch.
Normal Viewing
PICTURE
SETUP
SOUND
POS./SIZE
Select.
PICTURE
Select.
NORMALIZE NORMAL
STANDARD
25
0
0
0
5
NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
Press.
(Example:
PICTURE menu)
MEMORY SAVE
MEMORY LOAD
MEMORY EDIT
Set.
3 Set.
Set.
Press.
4 Exit the menu.
Press several times.
MENU
Press.
Press
to return to the previous menu.
Menu display list
Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
PICTURE menu
PICTURE
SETUP
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
MEMORY SAVE
MEMORY LOAD
MEMORY EDIT
see page 29-33
SETUP menu
STANDARD
25
0
0
0
5
NORMAL
POS./SIZE menu
1/2
TOUCH-PEN MODE
3D SETTINGS
SIGNAL
SCREENSAVER
EXTENDED LIFE SETTINGS
ECO MODE SETTINGS
INPUT LABEL
FUNCTION BUTTON SETTINGS
COMPONENT/RGB-IN SELECT
RGB
NO ACTIVITY POWER OFF
DISABLE
MENU DISPLAY DURATION
30 S
OSD BRIGHTNESS
5
OSD LANGUAGE
ENGLISH (US)
SETUP
2/2
SOUND menu
POS./SIZE
SOUND
NORMALIZE NORMAL
AUTO SETUP
H-POS
H-SIZE
V-POS
V-SIZE
DOT CLOCK
CLOCK PHASE
CLAMP POSITION
1:1 PIXEL MODE
see page 26-28
1/2
NORMALIZE NORMAL
AUDIO MENU
BASS
MID
TREBLE
BALANCE
SURROUND
0
0
0
0
0
0
0
OFF
SDI SOUND OUTPUT
LEFT CHANNEL
RIGHT CHANNEL
SOUND OUT
LEVEL METER
STANDARD
0
0
0
0
OFF
2/2
CHANNEL 1
CHANNEL 1
OFF
OFF
see page 34
MULTI DISPLAY SETUP
PORTRAIT SETUP
ON/OFF TIMER SETUP
DAY/TIME SETUP
NETWORK SETUP
DISPLAY ORIENTATION LANDSCAPE
see page 35-55
25
Adjusting POS./SIZE
1
2
Press to display the POS./SIZE menu.
Press to select the menu to adjust.
POS./SIZE
NORMALIZE NORMAL
AUTO SETUP
3
4
H-POS
H-SIZE
V-POS
V-SIZE
DOT CLOCK
CLOCK PHASE
CLAMP POSITION
1:1 PIXEL MODE
Press to adjust the menu.
Press to exit from adjust mode.
0
0
0
0
0
0
0
OFF
Note:
Unadjustable items are
grayed out.
Adjustable items differ
depending on the input signal
and the display mode.
Notes:
• Adjustment details are memorized separately for different input signal formats. (Adjustments for component signals are
memorized for 525 (480) / 60i &middot; 60p, 625 (575) / 50i &middot; 50p, 1125 (1080) / 60i &middot; 50i &middot; 60p &middot; 50p &middot; 24p &middot; 25p &middot; 30p &middot; 24sF,
1250 (1080) / 50i, 750 (720) / 60p &middot; 50p each, and RGB/PC/Digital signals are memorized for each frequency.)
• If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture
position movement cannot be controlled by the POS./SIZE function.
AUTO
SETUP
When inputting a PC signal as an example, “H-POS/V-POS”, “H-SIZE/V-SIZE”, “DOT CLOCK” and
“CLOCK PHASE” are automatically corrected.
This setting is enabled under the following conditions:
• When inputting an analog signal (Component/PC):
This setting is enabled if “COMPONENT/RGB-IN SELECT” (see page 52) in SETUP menu is “RGB”.
• When inputting a digital signal (HDMI/DVI):
A PC format signal enables this setting.
When the signal is not PC format, this setting is enabled only if “OVER SCAN” (see page 27) is “OFF” or
“1:1 PIXEL MODE” (see page 28) is “ON.” H-SIZE/V-SIZE is not automatically adjusted.
This setting will be invalid and will not work under the following conditions:
• When NETWORK input is selected.
• When VIDEO signal input
• During Multiple display, Portrait display or Digital Zoom.
• Aspect is set to “JUST”
• “Display size” in the Options menu (see page 57) is set to “On”
Using Remote Control
When
on the remote control is pressed, “AUTO SETUP” will be executed.
When AUTO SETUP does not work, “INVALID” is displayed.
Auto mode
When the “Auto Setup“ is set to “Auto” in the Options menu (see page 58), automatic position adjustment starts:
• When the display power is turned ON.
• When the input signal is switched.
26
Adjusting POS./SIZE
Notes:
• If the dot clock frequency of an analog signal is 162 MHz or higher, “DOT CLOCK” and “CLOCK PHASE”
cannot be automatically corrected.
• When digital signal input, DOT CLOCK and CLOCK PHASE cannot be made.
• AUTO SETUP may not work when a cropped or dark image is input. In such case, switch to a bright image
with borders and other objects are clearly shown, and then try auto setup again.
• Depending on the signal, out of alignment may occur after AUTO SETUP. Carry out ne tuning for the
position/size as required.
• If AUTO SETUP cannot set properly for vertical frequency 60Hz XGA signal (1024&times;768@60Hz,
1280&times;768@60Hz, and 1366&times;768@60Hz), pre-selecting the individual signal in “XGA MODE” (see page
53) may results in correct AUTO SETUP.
• AUTO SETUP does not work well when a signal such as additional information is superimposed out of
valid image period or intervals between synchronizing and image signals are short, or for image signal with
tri-level synchronizing signal added.
• If AUTO SETUP cannot adjust correctly, select “NORMALIZE” once and press ACTION ( ) then adjust
POS./SIZE manually.
H-POS
Adjust the horizontal position.
V-POS
Adjust the vertical position.
H-SIZE
Adjust the horizontal size.
V-SIZE
Adjust the vertical size.
DOT
CLOCK
(During Component/PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens,
adjust so that any such noise is minimized.
CLOCK
PHASE
(During Component/PC input signal)
Eliminate the ickering and distortion.
OVER
SCAN
Turn image over scan ON/OFF.
Congurable signals are as follows:
525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI)
ON
OFF
Notes:
• When “OFF” is set, “H-SIZE” and “V-SIZE” cannot be adjusted.
• When the “Display size” is set to “On” in the Options menu, this setting will be invalid. (see page 57)
27
Adjusting POS./SIZE
CLAMP POSITION (During Component/PC input signal)
Adjusts the clamp position when black parts of the image have no detail due to underexposure or are
tinged with green.
Optimum value for Clamp Position adjustment
When black parts have no detail due to underexposure (blackout)
Value that causes least blackout is the optimum.
When black parts are tinged with green
Value that cancels the greenishness without causing blackout is the optimum.
1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
• Select ON when you would like to replay 1920 &times; 1080 input signal.
• Applicable input signal;
1125 (1080) / 50i &middot; 60i &middot; 24sF &middot; 24p &middot; 25p &middot; 30p &middot; 50p &middot; 60p, 1250 (1080) / 50i
• Select OFF when ickering is shown around the image.
• H-SIZE and V-SIZE cannot be adjusted when ON is selected.
OFF
ON
1:1 PIXEL MODE When the input signal is a 2k1k signal (2048&times;1080 / 24p, 2048&times;1080 / 24sF), the display size is
(2k1k)
adjusted as follows.
(For 2k1k signals)
OFF
ON (LEFT)
ON (CENTER)
ON (RIGHT)
Note:
2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed.
Helpful Hint (
/
NORMALIZE
Normalization)
While the POS./SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
28
PICTURE Adjustments
1
2
Press to display the PICTURE menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by looking at the picture behind the menu.
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input
and menu setting.
PICTURE
Press the left or right
STANDARD
MONITOR
NORMALIZE NORMAL
STANDARD
25
0
0
0
5
NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
STANDARD
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of BRIGHTNESS
and PICTURE.
Press to enter Advanced
Settings.
ADVANCED SETTINGS
Enables ne picture adjustment at a professional
level (see next page).
ADVANCED SETTINGS
NORMALIZE NORMAL
0
0
BLACK EXTENSION
INPUT LEVEL
GAMMA
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
2.2
0
0
0
0
0
0
DYNAMIC
For viewing in brighter environments.
This menu selects higher than normal levels of
BRIGHTNESS and PICTURE.
CINEMA
For use in viewing tone-focused pictures with
brightness reduced.
MONITOR
For use when creating broadcast or movie content. With
this picture, even if the overall average picture level (APL)
changes, the brightness of areas with the same signal
level does not change.
PICTURE MENU during Touch Pen mode
Only “STANDARD” or “DYNAMIC” can be selected in
PICTURE MENU during Touch Pen mode.
If “CINEMA” or “MONITOR” has been selected and
you set to Touch Pen mode, the setting of PICTURE
MENU changes to “STANDARD”.
Notes:
When “MONITOR” is selected in PICTURE MENU, the
following menu items cannot be set.
EXTENDED LIFE SETTINGS: PEAK LIMIT (see page 42)
MULTI DISPLAY SETUP menu: VIDEO WALL UNIFORMITY (see page 49)
PORTRAIT SETUP menu: VIDEO WALL UNIFORMITY (see page 51)
If you would like to change the picture and color of the
selected PICTURE menu to something else, adjust using
the items in the PICTURE menu. (see next page)
Press the left
or right
NORMAL (9300K)
Helpful Hint (
/
button to switch between modes.
DYNAMIC
CINEMA
NORMALIZE
button to switch between modes.
COOL (11500K)
WARM (6500K)
Normalization)
While the “PICTURE” menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
29
PICTURE Adjustments
Item
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
Effect
Less
Adjustments
More
Darker
Brighter
Less
More
Reddish
Greenish
Less
More
Adjusts the proper picture contrast.
Adjusts for easier viewing of dark pictures
such as night scenes and black hair.
Adjusts color saturation.
Adjusts for natural esh tones.
Notes:
• You can change the level of each function
(PICTURE, BRIGHTNESS, COLOR, TINT,
SHARPNESS) for each PICTURE MENU.
• The setting details for STANDARD, DYNAMIC,
CINEMA and MONITOR respectively are
memorized separately for each input terminal.
• In PICTURE, there is not a noticeable change
even when contrast is increased with a bright
picture or reduced with a dark picture.
Adjusts picture sharpness.
ADVANCED SETTINGS
Item
BLACK
EXTENSION
INPUT
LEVEL
GAMMA
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
Effect
Details
Less
More
Less
More
Down
Up
Less
More
Less
More
Less
More
Less
More
Less
More
Less
More
Adjusts the dark shades of the image in gradation.
Adjustment of parts which are extremely bright and hard to see.
2.0
2.2
2.4
2.6
Adjusts the white balance for light red areas.
Adjusts the white balance for light green areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark green areas.
Adjusts the white balance for dark blue areas.
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B HIGH R” , “W/B HIGH G” and “W/B HIGH B” settings.
2. Adjust the white balance of the dark sections using the “W/B LOW R” , “W/B LOW G” and “W/B LOW B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Helpful Hint (
/
NORMALIZE
Normalization)
On the remote control unit, while the “ADVANCED SETTINGS” menu is displayed, if either the N button is pressed at any time
or the ACTION ( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
30
Picture Proles
Up to 8 combinations of picture adjustment values (in the PICTURE menu and ADVANCED SETTINGS) can be stored in
the display memory as proles and applied as needed, for a convenient way to enjoy your preferred picture settings.
PICTURE
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
CINEMA
18
0
0
0
3
NORMAL
Save proles (page 32)
MEMORY SAVE
MEMORY LOAD
MEMORY EDIT
PICTURE
NORMALIZE NORMAL
Load proles (page 33)
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
Edit proles (page 33)
CINEMA
25
0
0
0
5
NORMAL
Save proles
Edit the prole
Delete or rename
the prole
MY PICTURE
MEMORY2
MEMORY3
MEMORY4
MEMORY1
MEMORY2
MEMORY3
MEMORY4
MEMORY8
MEMORY8
Load the prole
Original picture
Custom picture
PICTURE
PICTURE
NORMALIZE NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
Save the picture adjustment
values in the MEMORY1
prole
Apply the MEMORY1
prole
NORMALIZE NORMAL
STANDARD
0
0
0
0
0
NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
CINEMA
25
0
0
0
5
NORMAL
31
Picture Proles
Saving proles
Follow these steps to save picture adjustment values as proles.
Note:
When the settings are locked in “EXTENDED LIFE SETTINGS”, proles cannot be saved.
1
Specify the picture quality in the PICTURE menu and
ADVANCED SETTINGS. (see page 29, 30)
2
In the PICTURE menu, select “MEMORY SAVE”.
MEMORY SAVE
1 select
MEMORY LOAD
MEMORY EDIT
3
5
2 access
A
N
a
n
0
!
_
Select a prole name for saving the picture adjustment
values.
1 select
MEMORY SAVE
1. [
2. [
3. [
4. [
]
]
]
]
C
P
c
p
2
#
|
MEMORY1
D E F
Q R S
d e f
q r s
3 4 5
$ % &amp;
~ &lt; &gt;
OK
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M ALL DELETE
Y Z
DELETE
l m
y z
SPACE
/ = ? @ \
ˆ
{
}
,
.
;
:
CANCEL
MEMORY1
All text is deleted.
To delete individual characters, select “DELETE”.
2 Select “M”.
M
Repeat this process to enter the next character.
3 Select “Y”.
1 select
MEMORY SAVE
SAVE THE ADJUSTED VALUE IN ”MEMORY1”
MY
2 set
4
CANCEL
Select “SPACE”.
MY
6
When you nished entering the prole name, select
“OK”.
To cancel saving the prole, select “CANCEL”.
1 select
MEMORY NAME INPUT
A
N
a
n
0
!
_
32
2 set
Example: Specifying “MY PICTURE”
1 Select “ALL DELETE”.
Select “OK”.
OK
B
O
b
o
1
”
`
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
“” appears for a prole in which the picture adjustments
have already been saved.
4
Enter a name for the prole.
[Entering prole names]
Prole names can be up to 40 characters.
To enter text, select characters in the on-screen
keyboard.
Edit the default profile name in the text box as
desired.
MEMORY NAME INPUT
1 select
B
O
b
o
1
”
`
C
P
c
p
2
#
|
MY PICTURE
D E F G
Q R S T
d e f g
q r s t
3 4 5 6
$ % &amp; ’
~ &lt; &gt; (
OK
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M ALL DELETE
Y Z
DELETE
l m
y z
SPACE
/ = ? @ \
ˆ
{
}
,
.
;
:
CANCEL
2 set
Picture Proles
Loading proles
Load proles and apply the picture adjustment values to the display as follows.
Notes:
• Loaded proles are stored in memory according to the selected input interface. (see page 18)
• When the settings are locked in “EXTENDED LIFE SETTINGS”, proles cannot be loaded.
Select the prole to load.
In the PICTURE menu, select “MEMORY LOAD”.
select
1
MEMORY SAVE
1
2
MEMORY LOAD
MEMORY LOAD
MEMORY EDIT
2 access
1. [
2. [
3. [
4. [
PC
When prole is being loaded,
prole name is displayed.
]
]
]
]
1 select
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
While in Touch Pen mode, a prole(s), whose
“PICTURE MENU” is set to “CINEMA” or
“MONITOR”, is grayed out and cannot be selected.
FULL
MEMORY NAME: MEMORY2
NANODRIFT
Editing proles
Delete or rename proles as follows.
&lt;Deleting proles&gt;
In the PICTURE menu, select “MEMORY EDIT”.
1 select
MEMORY SAVE
1
MEMORY LOAD
MEMORY EDIT
2
Select “MEMORY DELETE”.
1 select
MEMORY DELETE
MEMORY NAME CHANGE
4
2
MEMORY DELETE
MEMORY NAME CHANGE
3
4
MEMORY NAME CHANGE
]
]
]
]
1 select
DELETE THE ”MEMORY1” DATA.
Enter a name for the prole.
page 32
Entering prole names
A
N
a
n
0
!
_
2 set
CANCEL
5
1 select
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
1 select
MEMORY NAME INPUT
MEMORY DELETE
2 set
Select the prole to rename.
1. [
2. [
3. [
4. [
Select “OK”.
OK
1 select
MEMORY EDIT
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
ALL DELETE
2 access
Select “MEMORY NAME CHANGE”.
1 select
MEMORY DELETE
]
]
]
]
MEMORY LOAD
MEMORY EDIT
2 set
Select the prole to delete.
To delete all proles, select “ALL DELETE”.
1. [
2. [
3. [
4. [
1
2 access
MEMORY EDIT
3
&lt;Renaming proles&gt;
In the PICTURE menu, select “MEMORY EDIT”.
1 select
MEMORY SAVE
B
O
b
o
1
”
`
C
P
c
p
2
#
|
EMORY1
M
D E F
Q R S
d e f
q r s
3 4 5
$ % &amp;
~ &lt; &gt;
OK
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M ALL DELETE
Y Z
DELETE
l m
y z
SPACE
/ = ? @ \
ˆ
{
}
,
.
;
:
CANCEL
2 set
When you nished entering the prole name, select
“OK”.
To cancel renaming the prole, select “CANCEL”.
CANCEL
OK
1 select
2 set
33
SOUND Adjustment
1
SOUND
Press to display the SOUND menu.
1/2
NORMALIZE NORMAL
2
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by listening to the sound.
3
AUDIO MENU
BASS
MID
TREBLE
BALANCE
SURROUND
STANDARD
0
0
0
0
OFF
Press to exit from adjust mode.
Item
AUDIO MENU
BASS
MID
TREBLE
BALANCE
SURROUND
Details
STANDARD: Emits the original sound.
DYNAMIC: Accentuates sharp sound.
CLEAR:
Attenuates human voice.
Adjusts low pitch sounds.
Adjusts normal sounds.
Adjusts high pitch sound.
Adjusts left and right volumes.
Select ON or OFF.
Note: BASS, MID, TREBLE and SURROUND settings are memorized separately for each AUDIO MENU.
Helpful Hint (
/
NORMALIZE
Normalization)
While the “SOUND” menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
SDI SOUND OUTPUT
This menu is available only when selecting a slot that any of the following terminal boards is installed:
HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TY-FB11DHD)
SDI SOUND OUTPUT
LEFT CHANNEL
RIGHT CHANNEL
SOUND OUT
LEVEL METER
2/2
CHANNEL 1
CHANNEL 1
OFF
OFF
Item
SOUND OUT
LEVEL METER
34
Details
CHANNEL 1 to CHANNEL 16
LEFT CHANNEL Selects left audio channel.
CHANNEL 1 to CHANNEL 16
RIGHT CHANNEL Selects right audio channel.
OFF
ON
ON: Enables audio output.
OFF: Disables audio output.
1-8CH
9-16CH
OFF
Sets audio channels to show in the audio level meter.
8 channels are displayed in the audio level meter; 4 channels
each on both right and left sides of the display.
OFF: Hides the audio level meter.
1-8CH: Displays the audio level meter (1-8ch)
9-16CH: Displays the audio level meter (9-16ch)
SETUP menu
1
Press to display the SETUP menu.
Press to select the menu to adjust.
2
Press to adjust the menu.
3
4
SETUP
1/2
TOUCH-PEN MODE
3D SETTINGS
SIGNAL
SCREENSAVER
EXTENDED LIFE SETTINGS
ECO MODE SETTINGS
INPUT LABEL
FUNCTION BUTTON SETTINGS
COMPONENT/RGB-IN SELECT
RGB
NO ACTIVITY POWER OFF
DISABLE
30 S
MENU DISPLAY DURATION
5
OSD BRIGHTNESS
OSD LANGUAGE
ENGLISH (US)
Press to exit from adjust mode.
Press
to return to the previous menu.
SETUP menu screen
SETUP
1/2
TOUCH-PEN MODE
3D SETTINGS
SIGNAL
SCREENSAVER
EXTENDED LIFE SETTINGS
ECO MODE SETTINGS
INPUT LABEL
FUNCTION BUTTON SETTINGS
COMPONENT/RGB-IN SELECT
RGB
NO ACTIVITY POWER OFF
DISABLE
30 S
MENU DISPLAY DURATION
5
OSD BRIGHTNESS
OSD LANGUAGE
ENGLISH (US)
SETUP
Page 37
Page 38
Page 53
Page 39
Page 41
Page 44
Page 45
Page 46
Page 52
Page 47
Page 47
Page 47
Page 47
2/2
MULTI DISPLAY SETUP
PORTRAIT SETUP
ON/OFF TIMER SETUP
DAY/TIME SETUP
NETWORK SETUP
DISPLAY ORIENTATION LANDSCAPE
Page 48
Page 50
Page 36
Page 36
NETWORK SETUP
Page 47 Set this to connect the Display to a computer via a network. For details
of PJLink and Network, refer to “Operating Instructions, Network
Operations”.
35
DAY/TIME SETUP / ON/OFF TIMER SETUP
The timer can switch the Plasma Display ON or OFF.
Before attempting Timer Set, conrm the TIME and adjust if necessary. Then set POWER ON TIME / POWER OFF
TIME.
1
Press to display the SETUP menu.
2
Press to select ON/OFF TIMER SETUP or DAY/TIME
SETUP.
Press to display the ON/OFF TIMER SETUP screen or
DAY/TIME SETUP screen.
SETUP
2/2
MULTI DISPLAY SETUP
PORTRAIT SETUP
ON/OFF TIMER SETUP
DAY/TIME SETUP
NETWORK SETUP
DISPLAY ORIENTATION LANDSCAPE
DAY/TIME SETUP
1
2
Press to select DAY or TIME.
DAY/TIME SETUP
Press to set up DAY or TIME.
SET
button: Forward
DAY
button: Back
TIME
Notes:
• Pressing “ ” or “ ” button once changes TIME 1 minute.
• Pressing “ ” or “ ” button continuously changes TIME by 15 minutes.
TIME
MON 99:99
MON
99:99
Press to select SET.
Press to store DAY/TIME SETUP.
Notes:
• SET cannot be selected unless TIME is set.
• Unless setting the present time other than “99:99”, “DAY” and “TIME” cannot be set.
• The settings of “DAY” and “TIME” are reset when leaving the display turned off for about 7
days for the following reasons:
switch of the unit to turn off the display.
Pressing
Disconnecting the AC cord.
Interruption of power supply.
ON/OFF TIMER SETUP
1
Press to select POWER ON TIME / POWER OFF TIME.
button: Forward
button: Back
2
TIME
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
OFF
0:00
OFF
0:00
Notes:
• Pressing “ ” or “ ” button once changes POWER ON TIME
/ POWER OFF TIME 1 minute.
• Pressing “ ” or “ ” button continuously changes POWER ON TIME / POWER OFF
TIME by 15 minutes.
Press to select POWER ON FUNCTION / POWER OFF FUNCTION.
Press to select ON.
Note:
Timer function will not work unless “TIME” is set.
36
ON/OFF TIMER SETUP
Press to set up POWER ON TIME / POWER OFF TIME.
99:99
TOUCH-PEN MODE
Set Touch Pen mode.
Select “TOUCH-PEN MODE” in “SETUP” menu and press
button.
TOUCH-PEN MODE
SLOT INPUT
HDMI
DVI
PC
NETWORK
OFF
OFF
OFF
OFF
OFF
“SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A”
and “SLOT INPUT B” are displayed.
Set “ON” or “OFF” for each input terminal.
If you switch to the input terminal that is set to “ON”, the mode becomes Touch Pen mode.
TOUCH-PEN ON
“TOUCH-PEN: ON” is displayed in Touch Pen mode.
Notes:
• When the following signal input, “TOUCH-PEN MODE” are disabled:
50i/50p/25p/24sF/24p signals and PC format signals with 50 Hz vertical frequency.
• The electronic pen cannot be used when VIDEO or COMPONENT input is selected.
• When using the electronic pen, adjust “POS./SIZE” so that the screen of the computer can be correctly displayed.
(see page 26)
Setting the Remote Control
You can also turn Touch Pen mode ON/OFF with the FUNCTION buttons on the remote control. (see page 46)
In Touch Pen mode, the menus and functions are restricted as follows.
POS./SIZE menu
PICTURE menu
SETUP menu
3D SETTINGS
SIGNAL
EXTENDED LIFE SETTINGS
MULTI DISPLAY SETUP
PORTRAIT SETUP
Options menu
ASPECT Controls
Digital Zoom
1:1 PIXEL MODE: ON
OVER SCAN: OFF
PICTURE MENU: “STANDARD” or “DYNAMIC” only.
(see page 29)
3D FUNCTION: OFF
FRAME CREATION: OFF
PICTURE MENU: “STANDARD” or “DYNAMIC” only.
(see page 29)
MULTI DISPLAY SETUP: OFF
PORTRAIT SETUP: OFF
Display size: Unavailable
Rotate: Unavailable
FULL
Unavailable
37
3D SETTINGS
To view the 3D images, please adjust and setup the 3D settings.
Note:
Set these settings for each input terminals.
Select “3D SETTINGS” in “SETUP” menu and press
button.
3D SETTINGS sub-menu screen
3D SETTINGS
3D FUNCTION
3D INPUT FORMAT
LEFT/RIGHT SWAP
SAFETY PRECAUTIONS
ON
AUTO
NORMAL
• 3D FUNCTION
ON
OFF
ON: To view the 3D images, please set it to “ON”. You can see 3D images for 3D image signal and 2D images for 2D
image signal.
OFF: You can see 2D images instead of 3D images.
When set to “ON”, “3D” is displayed during 3D images.
PC
3D
FULL
NANODRIFT
• 3D INPUT FORMAT
3D images method is set.
AUTO: 3D images are automatically displayed according to the signal.
SIDE BY SIDE/TOP AND BOTTOM: One of the formats of the 3D standard. Select these formats as necessary.
NATIVE: Displays the input signal as it is. Use to identify the format type of the input signal.
• LEFT/RIGHT SWAP
NORMAL
SWAPPED
This function calibrates the timing to switch the right and left images as well as the timing to switch the shutter of right
and left 3D Eyewear.
Selects “SWAPPED” if you feel that the sense of depth is unusual.
• SAFETY PRECAUTIONS
Displays the precautions for viewing 3D images.
38
SCREENSAVER (For preventing image retention)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
1
2
Select “SCREENSAVER” in “SETUP” menu and press
button.
FUNCTION selection
Press to select the FUNCTION.
Press to select the desired function.
NEGATIVE IMAGE
WHITE SCREEN
SCROLLING BAR ONLY
OVERLAY SCROLLING BAR
SCREENSAVER
TIME
START
FUNCTION
MODE
99:99
SCROLLING BAR ONLY
OFF
NEGATIVE IMAGE
: A negative image will be displayed on the screen.
SCROLLING BAR ONLY : A white bar will scroll from left to right. The image won't be displayed.
OVERLAY SCROLLING BAR : The brightness of the image will be decreased and a white bar
will scroll on it.
WHITE SCREEN
: The whole screen will be white.
3
4
MODE selection
Press to select the
MODE.
Press to select each
mode items.
OFF
INTERVAL
: Operates when SHOW DURATION and SAVER
DURATION are set up and those times arrive.
: Operates when START TIME and FINISH TIME
TIME OF DAY
are set up and those times arrive.
STANDBY AFTER SCR SAVER: Operates while SCREENSAVER DURATION,
and display enters standby mode.
ON
: Operates when START is selected and the
ACTION ( ) button is pressed.
START setting
When the MODE is set to ON, press to select START.
Press to start SCREENSAVER.
The menu screen will disappear and the SCREENSAVER will be activated. To stop the
SCREENSAVER under ON, press the R button or any buttons on the main unit.
Note: When the display is turned off, the SCREENSAVER will be deactivated.
39
SCREENSAVER (For preventing image retention)
Setup of SCREENSAVER Time
After selecting TIME OF DAY, INTERVAL or STANDBY AFTER SCR SAVER, the relevant Time Setup will become available
for selection and the Operating Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.)
Press to select START TIME / FINISH TIME (when TIME OF
DAY is selected).
Press to select SHOW DURATION / SAVER DURATION
(when INTERVAL is selected).
Press to select SCREENSAVER DURATION (when
STANDBY AFTER SCR SAVER is selected).
Press to setup.
button: Forward
button: Back
Notes:
• Pressing “ ” or “ ” button once changes the Time 1 minute.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.
• “SCREENSAVER DURATION” of the “STANDBY AFTER SCR SAVER” can
be set from 0:00 to 23:59. When this is set to “0:00”, “STANDBY AFTER
SCR SAVER” will not be activated.
Note: Timer function will not work unless “TIME” is set.
40
SCREENSAVER
TIME
START
FUNCTION
MODE
START TIME
FINISH TIME
15:00
SCROLLING BAR ONLY
TIME OF DAY
6:15
12:30
SCREENSAVER
TIME 15:00
START
SCROLLING BAR ONLY
FUNCTION
INTERVAL
MODE
12:00
SHOW DURATION
3:00
SAVER DURATION
SCREENSAVER
TIME 15:00
START
SCROLLING BAR ONLY
FUNCTION
STANDBY AFTER SCR SAVER
MODE
6:15
SCREENSAVER DURATION
Reduces screen image retention
EXTENDED LIFE SETTINGS
The following settings are setup to reduce image retention:
Select “EXTENDED LIFE SETTINGS” in “SETUP” menu and press
button.
EXTENDED LIFE SETTINGS
EXPRESS SETTINGS
CUSTOM SETTINGS
RESET
Set to the recommended value
Set individually
Reset to the factory settings
EXTENDED LIFE SETTINGS
RECOMMENDED SETTINGS
PICTURE MENU
PICTURE
SIDE BAR ADJUST
NANODRIFT SAVER
PEAK LIMIT
LOCK SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
DYNAMIC
30
BRIGHT
MID
OFF
UNLOCK
Image Retention Reduction Menu
Image Retention Reduction Menu
“EXTENDED LIFE SETTINGS” enables you to set the following 5 menus (Image Retention Reduction Menu) as
recommended values or set them individually.
PICTURE MENU
PICTURE
“PICTURE MENU” and “PICTURE” are same as “PICTURE” menu items (see page 29). The settings of this menu will be
reected to the “PICTURE” menu.
SIDE BAR ADJUST
Do not display a picture in 4:3 mode for an extended period,
as this can cause an image retention to remain on the side
bars on either side of the display eld.
To reduce the risk of such an image retention, illuminate the
side bars.
This function may be applicable to the non-picture area.
OFF:
DARK:
MID:
BRIGHT:
side bars
4:3 mode
image
retention
Darken both ends.
Make it dark gray.
Make it gray.
Make it light gray.
Notes:
• To reduce the occurrence of image retention, set the SIDE BAR ADJUST to BRIGHT.
• The side bar may ash (alternate black/white) depending on the picture being shown on the screen. Using Cinema mode
will reduce such ashing.
41
Reduces screen image retention
NANODRIFT SAVER
Moves the display position of the screen slightly to reduce image retention on the display panel.
LOW–HIGH: NANODRIFT SAVER operates. The display position of the screen moves at set time intervals. You can set
the screen movement range. Some of the screen may appear to be missing as a result of this operation.
If you change the value, a mask is displayed in the range where the picture is missing as a result of
position movement.
When “NANODRIFT” Image Retention Reduction is operating, “NANODRIFT”
is displayed.
PC
Note:
This function does not work in the following cases.
When “MULTI DISPLAY SETUP” is set to “ON”
When “PORTRAIT SETUP” is set to “ON”
When in digital zoom mode
PEAK LIMIT
ON: Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 63)
EXPRESS SETTINGS
Set the “Image Retention Reduction” menu to the recommended settings.
All menus will be locked.
PICTURE MENU: STANDARD
PICTURE: Recommended setting for each model
SIDE BAR ADJUST: BRIGHT
NANODRIFT SAVER: MID
PEAK LIMIT: ON
1 Select “EXPRESS SETTINGS”.
EXTENDED LIFE SETTINGS
EXPRESS SETTINGS
CUSTOM SETTINGS
RESET
2 Select the input to apply the settings.
EXTENDED LIFE SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
3 Select “YES”.
EXTENDED LIFE SETTINGS
1 select
2 access
1 select
2 set
1 select
APPLY TO CURRENT INPUT
YES
42
NO
2 set
FULL
NANODRIFT
Reduces screen image retention
CUSTOM SETTINGS
Set the individual “Image Retention Reduction” menu.
1 Select “CUSTOM SETTINGS”.
EXTENDED LIFE SETTINGS
EXPRESS SETTINGS
CUSTOM SETTINGS
RESET
1 select
2 access
set each menu to the recommended setting:
2 To
Select “RECOMMENDED SETTINGS”.
EXTENDED LIFE SETTINGS
1 select
RECOMMENDED SETTINGS
PICTURE MENU
PICTURE
SIDE BAR ADJUST
NANODRIFT SAVER
PEAK LIMIT
LOCK SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
3
DYNAMIC
30
BRIGHT
MID
OFF
UNLOCK
2 set
RECOMMENDED SETTINGS
PICTURE MENU
PICTURE
SIDE BAR ADJUST
NANODRIFT SAVER
PEAK LIMIT
LOCK SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
DYNAMIC
30
BRIGHT
MID
OFF
UNLOCK
RECOMMENDED SETTINGS
PICTURE MENU
PICTURE
SIDE BAR ADJUST
NANODRIFT SAVER
PEAK LIMIT
LOCK SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
DYNAMIC
30
BRIGHT
MID
OFF
LOCK
DYNAMIC
30
0
0
0
5
NORMAL
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
TINT
SHARPNESS
COLOR TEMP
ADVANCED SETTINGS
EXTENDED LIFE SETTINGS
1 select
Touch Pen mode when a menu is locked
When a menu is locked, “TOUCH-PEN MODE” are
disabled and Touch Pen mode cannot be set.
2 adjust
5 Select the input to apply the settings.
EXTENDED LIFE SETTINGS
1 select
RECOMMENDED SETTINGS
lock each menu setting:
4 To
Set the “LOCK SETTINGS” to “LOCK”.
EXTENDED LIFE SETTINGS
PICTURE
NORMALIZE NORMAL
MEMORY SAVE
MEMORY LOAD
MEMORY EDIT
Each menu will be set as same as
the “EXPRESS SETTINGS”.
Set each menu.
EXTENDED LIFE SETTINGS
When a menu is locked, it is grayed out and cannot be set.
“PICTURE MENU” and “PICTURE” will no longer
be able to set in the “PICTURE” menu, and they are
labeled with icon to indicate their locked status. Also,
“NORMALIZE”, “MEMORY SAVE” and “MEMORY
LOAD” are not available.
1 select
2 adjust
PICTURE MENU
PICTURE
SIDE BAR ADJUST
NANODRIFT SAVER
PEAK LIMIT
LOCK SETTINGS
APPLY TO CURRENT INPUT
APPLY TO ALL INPUTS
DYNAMIC
30
BRIGHT
MID
OFF
LOCK
6 Select “YES”.
EXTENDED LIFE SETTINGS
2 set
1 select
APPLY TO CURRENT INPUT
YES
NO
2 set
RESET
Reset the “Image Retention Reduction” menu to the factory settings. Each menu will be unlocked.
1 Select “RESET”.
EXTENDED LIFE SETTINGS
EXPRESS SETTINGS
CUSTOM SETTINGS
RESET
2 Select the input to reset the settings.
EXTENDED LIFE SETTINGS
RESET CURRENT INPUT
RESET ALL INPUTS
1 select
3 Select “YES”.
EXTENDED LIFE SETTINGS
1 select
RESET CURRENT INPUT
2 access
YES
NO
2 set
1 select
2 set
43
ECO MODE SETTINGS
Select “ECO MODE SETTINGS” in “SETUP” menu and press
button.
ECO MODE SETTINGS
ECO MODE
CUSTOM
OFF
ON
POWER SAVE
STANDBY SAVE
PC POWER MANAGEMENT
DVI-D POWER MANAGEMENT
NO SIGNAL POWER OFF
1 select
2 adjust
OFF
OFF
DISABLE
ECO MODE
CUSTOM: The menu of power consumption reduction is individually set.
ON: The following xed values are set to the menu of power consumption reduction. Individual setting is not available.
POWER SAVE: ON
DVI-D POWER MANAGEMENT: ON
STANDBY SAVE: ON
NO SIGNAL POWER OFF: ENABLE
PC POWER MANAGEMENT: ON
Using Remote Control
When
is pressed, the “ECO MODE” setting changes.
ECO MODE
ON
Custom settings
The menu of the power consumption reduction is individually set. This setting is enabled when “ECO MODE” is set to
“CUSTOM”.
POWER SAVE
When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced.
STANDBY SAVE
When this function is turned ON, power consumption of the microcomputer is reduced during power supply standby (see
page 16, 19, 20), so standby power of the set is reduced.
PC POWER MANAGEMENT
When this function is set to ON, it operates under the following conditions to turn the power on or off automatically.
When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal input:
Power is turned off (standby); the power indicator lights up orange.
When pictures (HD/VD sync signals) are subsequently detected:
Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during PC signal input.
• This function is effective when “SYNC” is set to “AUTO”, “COMPONENT / RGB-IN SELECT” is set to “RGB” and during
normal viewing.
DVI-D POWER MANAGEMENT
When this function is set to ON, it operates under the following conditions to turn the power on or off automatically.
When no pictures (sync signal) are detected for 30 or so seconds during DVI signal input:
Power is turned off (standby); the power indicator lights up orange.
When pictures (sync signal) are subsequently detected:
Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during DVI signal input.
• This function is invalid during input from DVI-D Terminal Board (TY-FB11DD).
• Depending on the type of terminal board equipped, this function may be invalid.
NO SIGNAL POWER OFF
Equipment power supply is turned OFF when there is no signal.
When this is set to “ENABLE”, the power supply of the unit goes Off 10 minutes after the input signals stop.
44
Customizing the Input labels
This function can change the label of the Input signal to be displayed. (see page 18)
Select “INPUT LABEL” in “SETUP” menu and press
button.
INPUT LABEL
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
Image input
[SLOT INPUT]*1
[VIDEO]
[COMPONENT]*2
[HDMI]
[DVI]
[PC]
[NETWORK]
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
Input label
SLOT INPUT / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (SKIP)
VIDEO / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV / VCR /
STB / (SKIP)
COMPONENT / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (SKIP)
HDMI / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV / VCR /
STB / (SKIP)
DVI / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV / VCR / STB /
(SKIP)
PC / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV / VCR / STB /
(SKIP)
NETWORK / (SKIP)
(SKIP) : The INPUT button press will skip its input.
*1 “SLOT INPUT” is displayed when a Terminal Board is installed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
(see page 52)
When a Terminal Board with dual input terminals is installed
“SLOT INPUT” is displayed as “SLOT INPUT A” and “SLOT INPUT B” and independent settings are available.
[SLOT INPUT A]
[SLOT INPUT B]
SLOT INPUT A / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV / VCR /
STB / (SKIP)
SLOT INPUT B / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (SKIP)
When a Terminal Board with xed display (such as Tuner Board) is installed
Only xed display and (SKIP) are available as Input label of “SLOT INPUT”.
[SLOT INPUT]
xed display / (SKIP)
45
FUNCTION BUTTON SETTINGS
Set the functions that operates when
is pressed.
FUNCTION BUTTON SETTINGS
Select “FUNCTION BUTTON SETTINGS” in “SETUP” menu and
press
FUNCTION BUTTON 1
TOUCH-PEN
FUNCTION BUTTON 2
SCROLLING BAR
FUNCTION BUTTON GUIDE
ON
button.
• FUNCTION BUTTON 1, FUNCTION BUTTON 2
The following functions are set to the FUNCTION button.
ECO MODE SETTINGS / 3D SETTINGS / SIGNAL / ON/OFF TIMER SETUP
Note:
Factory settings are as follows.
FUNCTION1 button: TOUCH-PEN
FUNCTION2 button: SCROLLING BAR
Menu is displayed. (Example: ECO MODE SETTINGS)
ECO MODE SETTINGS
ECO MODE
POWER SAVE
STANDBY SAVE
PC POWER MANAGEMENT
DVI-D POWER MANAGEMENT
NO SIGNAL POWER OFF
CUSTOM
OFF
ON
OFF
OFF
DISABLE
Pressing the FUNCTION button clears the menu.
SCROLLING BAR
Activates the SCROLLING BAR ONLY screensaver.
After 15 minutes, the display enters standby mode.
To exit this mode, press any button.
INPUT (SLOT)* – INPUT (NETWORK)
to select the input.
Simply press
* “INPUT (SLOT)” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “INPUT (SLOT A)” and “INPUT (SLOT B)” are displayed.
TOUCH-PEN
and turn Touch Pen mode ON/OFF.
Press
TOUCH-PEN
ON
NETWORK SETUP
“NETWORK SETUP” menu is displayed.
COMPUTER SEARCH
The list of connectable computers on the network is displayed.
MULTI-LIVE
Switch to the MULTI-LIVE mode when using the “Wireless
Manager mobile edition 5.5”.
AV MUTE
Mutes the audio and video. To exit this mode, press any button.
• FUNCTION BUTTON GUIDE
The function display setting for the FUNCTION button is congured.
ON: Press the FUNCTION button to display the function list of the button.
OFF: The function list is not displayed.
The operation starts.
FUNCTION
1:TOUCH-PEN
46
2:SCROLLING BAR
NO ACTIVITY POWER OFF
DISABLE
ENABLE
When this function is set to “ENABLE”, the power is turned off (standby) automatically when there is no operation of the
Plasma Display for 4 hours.
Starting from 3 minutes before the turn off, the remaining time will be displayed.
PRESS ANY KEY TO ABORT.
NO ACTIVITY POWER OFF
3MIN
When the power is turned off due to this function, a message “LAST TURN OFF DUE TO ’NO ACTIVITY POWER
OFF’.” is displayed next time the power is turned on.
Note:
During the screensaver is running, this function is disabled.
MENU DISPLAY DURATION / OSD BRIGHTNESS
Set the display time and brightness of the on-screen menu display.
MENU DISPLAY DURATION: 5 S – 30 S
OSD BRIGHTNESS: 1 – 5
OSD LANGUAGE
Select your preferred language.
Selectable languages
English(UK)
Deutsch
Fran&ccedil;ais
Italiano
Espa&ntilde;ol
ENGLISH(US)
(Chinese)
(Japanese)
(Russian)
DISPLAY ORIENTATION
Sets the fan control, panel drive control, and the display style of on-screen menu for vertical installation.
LANDSCAPE
PORTRAIT
Fan control and panel drive control Fan control and panel drive control for vertical installation. On-screen menu
for horizontal installation.
will be rotated 90 degrees counterclockwise to be suitable for the setting.
Notes:
• Turn up the power switch for the upward direction when you set Display vertically.
• When you change this setting, fan control and panel drive control will be switched as the power is turned on next time.
47
SETUP for MULTI DISPLAY
By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
Notes:
• During Touch Pen mode, “MULTI DISPLAY SETUP” becomes “OFF” and this function cannot be used.
• During Multi display, the 3D images are displayed as 2D images.
(Example)
group of 4 (2 &times; 2) group of 9 (3 &times; 3)
group of 16 (4 &times; 4)
group of 25 (5 &times; 5)
How to setup MULTI DISPLAY
1
2
Select “MULTI DISPLAY SETUP” in “SETUP” menu and press
button.
Press to select the MULTI DISPLAY SETUP.
OFF
&times;2
&times;2
OFF
A1
OFF
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
VIDEO WALL UNIFORMITY
Press to select “ON” or “OFF”.
Item
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
Details
Select “ON” or “OFF”.
Note: If you set MULTI DISPLAY SETUP to ON, PORTRAIT SETUP will be unavailable.
HORIZONTAL SCALE
Select “&times; 1”, “&times; 2”, “&times; 3”, “&times; 4”, “&times; 5”.
VERTICAL SCALE
Select “&times; 1”, “&times; 2”, “&times; 3”, “&times; 4”, “&times; 5”.
Select “ON” or “OFF”.
To hide joints between displays.
To show joints between displays.
Suitable for moving image display.
Suitable for still image display.
ON
OFF
SEAM HIDES VIDEO
Select the required arrangement number. (A1-E5 : Refer to the following)
Display Number locations for each arrangement.
(Examples)
( 2 &times; 1) ( 2 &times; 3 )
(4&times;2)
(4&times;4)
LOCATION
48
(5&times;5)
A1
A2
A3
A4
B1
B2
B3
B4
A5
B5
C1
C2
C3
C4
C5
D1
D2
D3
D4
D5
E1
E2
E3
E4
E5
SETUP for MULTI DISPLAY
Item
Details
Reduces the peak of brightness for each display to enable as uniform display as possible.
The brightness difference is
The brightness depends on each
Select “OFF” or “ON”.
minimized.
display’s setting.
VIDEO WALL
UNIFORMITY
OFF
ON
Note:
If you set VIDEO WALL UNIFORMITY to ON, the following menus will be unavailable and
these settings will be xed to the initial values.
PICTURE menu: COLOR, TINT, INPUT LEVEL (ADVANCED SETTINGS)
ID Remote Control Function
You can set the remote control ID when you want to use this remote control on one of several different displays.
Note:
To operate this function, please purchase ID remote controller sold separately.
Object model : EUR7636070R
1
2
3
4
Switch
to
on the right side.
Press the
button on the remote control.
Press one of
-
,
for the tens digit setting.
Press one of
-
,
for the units digit setting.
Notes:
• The numbers in 2, 3 and 4 should be set up quickly.
• Adjustable ID number range is 0 - 99.
• If a number button is pressed more than two times, the rst two numbers become the ID number
for the remote control.
ID remote control button operation
The operation is the same as normal remote control except for the
button.
ID Cancellation
Press
button on remote control. (This has the same effect as pressing the
,
,
buttons at the same time.)
Notes:
• Set the Remote ID “On” to operate the ID remote control.
If Remote ID is set to “On”, you can use the remote control without identical ID number during option menu display.
(see page 57)
• The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is not
the same as the ID select number (see page 57).
49
SETUP for PORTRAIT
Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged 3
times and rotated 90-degree.
(Example)
Notes:
• During Touch Pen mode, “PORTRAIT SETUP” becomes “OFF” and this function cannot be used.
• When using the PORTRAIT function with displays set vertically, “DISPLAY ORIENTATION” in SETUP menu has to be
set to “PORTRAIT” (see page 47).
• Turn up the power switch for the upward direction when you set Display vertically.
• During Portrait display, the 3D images are displayed as 2D images.
How to setup PORTRAIT
1
Select “PORTRAIT SETUP” in “SETUP” menu and press
button.
Press to select the PORTRAIT SETUP.
2
Press to select “ON” or “OFF”.
Note:
If you set PORTRAIT SETUP to ON, MULTI
DISPLAY SETUP will be unavailable.
Press to select SEAM HIDES VIDEO.
3
Press to select “OFF” , “ON”.
To hide joints between displays.
To show joints between displays.
Suitable for moving image display.
Suitable for still image display.
ON
OFF
50
PORTRAIT SETUP
PORTRAIT SETUP
SEAM HIDES VIDEO
VIEWING AREA
LOCATION
VIDEO WALL UNIFORMITY
OFF
OFF
16:9
1
OFF
PORTRAIT SETUP
PORTRAIT SETUP
SEAM HIDES VIDEO
VIEWING AREA
LOCATION
VIDEO WALL UNIFORMITY
OFF
OFF
16:9
1
OFF
SETUP for PORTRAIT
4
VIEWING AREA / LOCATION
VIEWING AREA: Set a mode of image division for PORTRAIT function.
LOCATION: Set a location of image to be displayed for PORTRAIT function.
Press to select VIEWING AREA or LOCATION.
Press to select each function.
PORTRAIT SETUP
PORTRAIT SETUP
SEAM HIDES VIDEO
VIEWING AREA
LOCATION
VIDEO WALL UNIFORMITY
Notes:
• For HD signal videos, the “VIEWING AREA” is set at “16:9”,
and cannot be changed.
HD signal: 1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p
• 24sF, 750 (720) / 60p • 50p, 1250 (1080) / 50i
• When “VIEWING AREA”is “16:9”, the aspect mode is set to “FULL”.
LOCATION setting
When PORTRAIT SETUP “ON”:
Display the image of the selected LOCATION.
OFF
OFF
16:9
1
OFF
When PORTRAIT SETUP is “OFF”:
Represent an area of the selected LOCATION at a normal
brightness and darken the rest of it.
VIEWING AREA and LOCATION
The mode of image division and the LOCATION by setting of VIEWING AREA is as follows.
VIEWING AREA: 16:9
Suitable to display FULL images. NORMAL
(4:3) images extend transversely.
Both right and left sides of the image are
cut by 48 dots.
LOCATION 1
LOCATION 2
Undisplayed area (48 dots)
LOCATION 3
VIEWING AREA: 4:3
LOCATION 1
5
LOCATION 2
LOCATION 3
4:3 images are displayed without changing
aspect ratio.
Although the images of each LOCATION
overlap, you can adjust POS./SIZE to display
the image normally. (see page 26)
VIDEO WALL UNIFORMITY
Reduces the peak of brightness for each display to enable as uniform display as possible.
Press to select VIDEO WALL UNIFORMITY.
Press to select “OFF” , “ON”.
The brightness depends on The brightness difference
each display’s setting.
is minimized.
OFF
ON
PORTRAIT SETUP
PORTRAIT SETUP
SEAM HIDES VIDEO
VIEWING AREA
LOCATION
VIDEO WALL UNIFORMITY
OFF
OFF
16:9
1
OFF
Note:
If you set VIDEO WALL UNIFORMITY to ON,
the following menus will be unavailable and
these settings will be xed to the initial values.
PICTURE menu: COLOR, TINT, INPUT
LEVEL (ADVANCED
SETTINGS)
51
SETUP for Input Signals
COMPONENT / RGB IN SELECT
COMPONENT
RGB
Select to match the signals from the source connected to the Component / RGB or PC input terminals.
“COMPONENT”
Y, PB, PR signals
“RGB”
RGB signals
Note:
Make setting of the selected input terminal (COMPONENT/RGB IN or PC IN).
YUV / RGB IN SELECT
YUV
RGB
Select to match the signals from the source connected to the DVI input terminals.
“YUV”
YUV signals
“RGB”
RGB signals
Notes:
• Selection may not be possible, depending on which optional board is installed.
• Make setting of the selected input terminal (SLOT or DVI-D IN).
52
SETUP for Input Signals
SIGNAL menu
Note:
“SIGNAL” setup menu displays a different setting condition for each input signal.
Select “SIGNAL” in “SETUP” menu and press
For VIDEO (S VIDEO)
For RGB
[ VIDEO ]
SIGNAL
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
NOISE REDUCTION
[ RGB ]
SIGNAL
SYNC
3 : 2 PULLDOWN
XGA MODE
NOISE REDUCTION
ON
AUTO
OFF
OFF
AUTO
OFF
AUTO
OFF
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280&times;1024/60i
For COMPONENT
[ COMPONENT ]
SIGNAL
button.
For Digital
[ Digital ]
SIGNAL
SYNC
3 : 2 PULLDOWN
XGA MODE
NOISE REDUCTION
AUTO
OFF
AUTO
OFF
3 : 2 PULLDOWN
NOISE REDUCTION
OFF
OFF
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
DOT CLOCK FREQ. 108.0 MHz
SIGNAL FORMAT 1280&times;1024/60i
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280&times;1024/60i
• 3D Y/C FILTER (NTSC)
This menu is displayed when BNC Dual Video Terminal Board (TY-FB9BD) is installed to the unit.
Set this menu when the moving image looks unnatural during Video (S Video) input signal.
OFF
ON
Note:
When ON, this setting only affects NTSC input signals.
• COLOR SYSTEM
AUTO
PAL
SECAM
M.NTSC
NTSC
Set the color system to match the input signal. When “AUTO” is set, COLOR SYSTEM will be automatically selected
from NTSC/PAL/SECAM/M.NTSC.
To display PAL60 signal, select “AUTO” or “PAL”.
If the image becomes unstable:
With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become
unstable. Should this occur, set the system to match the format of the input signal.
3:2 PULLDOWN
When “ON”, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which
are recorded at 24 frames per second.
If the picture is not stable, turn the setting to “OFF”.
OFF
ON
Note:
When ON, this setting only affects the following signal input:
• NTSC / PAL signal input during Video (S Video) input signal.
• 525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal.
• XGA MODE
This menu is displayed when the input signal is analog (Component/PC).
This unit supports three types of XGA signals with 60Hz vertical frequency having different aspect ratios and sampling
rates (1,024 &times; 768 @ 60Hz, 1,280 &times; 768 @ 60Hz and 1,366 &times; 768 @ 60Hz).
1024&times;768
1280&times;768
1366&times;768
AUTO
AUTO: Automatically selected from 1024&times;768/1280&times;768/1366&times;768.
Switch the setting to suit the input signal for better display depends on the angle of view or display resolution condition.
Note:
After making this setting, be sure to make each adjustment (such as “AUTO SETUP”) on the “POS./SIZE” menu as
necessary. (see page 26)
53
SETUP for Input Signals
• SYNC
This function operates only during input from PC IN terminal.
Setting RGB sync signal
Conrm that the input is set to RGB input (this setting is valid only for RGB input signal).
AUTO: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
Setting Component sync signal
Conrm that the input is set to Component input (this setting is valid only for Component input signal).
AUTO: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
ON Y: Uses a synchronized signal on the Video Y signal, which is input from the Y connector.
Note:
Signals input to COMPONENT/RGB IN terminals correspond to SYNC ON G or SYNC ON Y.
• SDI THROUGH
Set the active through function of the Dual Link HD-SDI Terminal Board (TY-FB11DHD).
OFF
ON
ON: Enables active through.
OFF: Disables active through.
Note:
Settings can only be performed for this menu when a slot mounted with a Dual Link HD-SDI Terminal Board (TY-FB11DHD)
is selected.
• FRAME CREATION
Automatically compensates the picture frame rate and removes juddering movements to make the images smooth.
MID
MAX
OFF
Note:
Depending on the contents, images may be noisy. To prevent the noise, change the setting.
• 3D REFRESH RATE
Reduces juddering or icker of image due to lighting interference during 3D viewing.
120Hz
100Hz
Note:
This setting is disabled when “FRAME CREATION” is set to “OFF”.
• HDMI RANGE
Switches the dynamic range according to the input signal from HDMI terminal.
FULL(0-255)
AUTO
VIDEO(16-235)
VIDEO(16-235): If the input signal is the video range, Example: HDMI terminal output for DVD player
FULL(0-255): If the input signal is full range, Example: HDMI terminal output for personal computer
AUTO: Switches the dynamic range automatically between “VIDEO(16-235)” and “FULL(0-255)” according to the input signal.
Note:
This function can be set only for HDMI signal input.
54
SETUP for Input Signals
• NOISE REDUCTION
Sets the following three NR (Noise Reduction) functions together.
VIDEO NR, MOSQUITO NR, BLOCK NR
Press to select “NOISE REDUCTION”.
(
)
NOISE REDUCTION
OFF
(
)
NOISE REDUCTION
ADVANCED
Press to select “OFF”, “MIN”, “MID”, “MAX”,
“ADVANCED”.
Advanced NR
Sets the three NR functions separately.
1
Press to select “ADVANCED”.
ADVANCED NR
Press to enter ADVANCED NR.
2
Press to select VIDEO NR,
MOSQUITO NR or BLOCK NR.
Press to select “OFF”, “MIN”, “MID”,
“MAX”.
VIDEO NR
MOSQUITO NR
BLOCK NR
ADVANCED NR
VIDEO NR
MOSQUITO NR
BLOCK NR
[ VIDEO ]
VIDEO NR
MOSQUITO NR
BLOCK NR
OFF
OFF
OFF
[ COMPONENT ]
OFF
OFF
OFF
ADVANCED NR
ADVANCED NR
VIDEO NR
MOSQUITO NR
BLOCK NR
[ RGB ]
OFF
OFF
OFF
[ Digital ]
OFF
OFF
OFF
VIDEO NR:
Automatically reduces unwanted picture noise.
MOSQUITO NR: Reduces mosquito noise around subtitles on MPEG videos.
BLOCK NR:
Reduces block noise when playing MPEG videos.
Note:
NOISE REDUCTION cannot be adjusted while a PC signal is being applied.
• Input signal display
Displays the frequency and the type of the current input signal.
This display is valid only for COMPONENT/RGB/PC and Digital input signal.
Display range:
Horizontal 15 - 110 kHz
Vertical
48 - 120 Hz
The dot clock frequency is displayed during DVI signal input.
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
SIGNAL FORMAT 1280&times;1024/60i
H-FREQ. 63.98 kHz
V-FREQ. 60.02 Hz
DOT CLOCK FREQ. 108.0 MHz
SIGNAL FORMAT 1280&times;1024/60i
55
Options Adjustments
Options
1
Press to display the SETUP menu.
Weekly Command Timer
Audio input select
Input Search
Press to select “OSD LANGUAGE”.
2
Onscreen display
Initial input
Initial VOL level
Maximum VOL level
Input lock
Button lock
Remocon User level
Press for more than 3 seconds.
Press to select “Options”.
3
Options
Shipping
Press to display the Options menu.
Press to select your preferred menu.
4
Press to adjust the menu.
5
On
Off
Off
0
Off
0
Off
Off
Off
Options
2/3
Off-timer function
Enable
Initial Power Mode
ID select
Remote ID
Serial ID
Display size
Studio W/B
Studio Gain
Normal
Options
0
Off
Off
Off
Off
Off
3/3
Off
Slot power
Off
Power On Screen Delay
Clock Display
Off
All Aspect
Off
Auto Setup
Manual
Rotate
Off
Advanced Motion Resolution
On
Power On Message (No activity power off)
On
3D Safety Precautions
On
Press to exit from Options menu.
Item
1/3
Adjustments
Weekly Command Timer Sets Weekly Command Timer. (see page 59)
Audio input select Set up the sound when an image input is selected. (see page 61)
Input Search
Set auto input switching for when there is no signal. (see page 62)
On: Displays all the following on screen.
• Power on display
• Input signal switch display
Onscreen display
• No signal display
was pressed.
• Mute and the remaining time of off-timer after
Off: Hides all the items above from view.
Adjusts the input signal when the unit is turned on.
SLOT INPUT*1
VIDEO
COMPONENT*2
HDMI
DVI
PC
NETWORK
Off
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
Initial input
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”. (see page 52)
Notes:
• Only the adjusted signal is displayed. (see page 18)
• This menu is available only when “Input lock” is “Off”.
Initial VOL level
button to adjust the volume when the unit is turned on.
Press
On
Off
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
• When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL level
button to adjust the maximum volume.
Press
On
Off
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
56
Options Adjustments
Item
Adjustments
Input lock
Locks the input switch operation.
SLOT INPUT*1
VIDEO
COMPONENT*2
HDMI
DVI
PC
NETWORK
Off
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
(see page 52)
Notes:
• Only the adjusted signal is displayed (see page 18).
• Input switch can be used when this is set to “Off”.
Off
MENU&amp;ENTER
On
Off: All the buttons on main unit can be used.
MENU&amp;ENTER: Locks
and
buttons on main unit.
On: Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
Off: Press four timesPress
four timesPress four timesPress
MENU&amp;ENTER: Press
four timesPress four timesPress
four timesPress
On: Press four timesPress
four timesPress four timesPress
MENU
Button lock
ENTER/
ENTER/
INPUT
ENTER/
INPUT
ENTER/
Remocon User level
ENTER/
ENTER/
Off
User1
User2
User3
Off: You can use all of the buttons on the remote control.
User1: You can only use
, , , ,
buttons on the remote control.
button on the remote control.
User2: You can only use
User3: Locks all the buttons on remote control.
Off-timer function
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Note: When “Disable” is set, the Off-timer is cancelled.
Initial Power Mode
Normal
Standby
On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Power returns in power On. (Power Indicator : green)
Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
ID select
Remote ID
Serial ID
Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and
display unit. About the setting method, please refer to “ID Remote Control Function” (see page 49)
and “ID select” (above-mentioned).
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Display size
Notes:
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (Video)
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when digital zoom, Multi display or Portrait display is selected.
• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS./SIZE” can be adjusted.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
57
Options Adjustments
Item
Adjustments
Studio W/B
Off: Nullify all the settings adjusted.
On: Sets the color temperature for TV studio.
Note: Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu.
Studio Gain
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note: This setting is valid only when the input signals are as follows:
Component Video, RGB (analog), SDI, HDMI
Slot power
Off
Off:
Auto:
On:
Note:
Power On Screen
Delay
Clock Display
Auto
On
Power is not transmitted to the slot power.
Power is transmitted to the slot power only when main power is on.
Power is transmitted to the slot power when main power is on or in the standby state.
In some cases, power is transmitted to the slot power when main power is on or in the standby state
regardless of the slot power setting.
Off
1
2
3....
30
You can set the power-on delay time of the displays to reduce the power load, when you press
to turn
on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display’s setting individually.
Off:
The display will be turned on at the same time as
is pressed.
1 to 30 (sec.): Set the power-on delay time (second).
After pressing
, the display will be powered on with time delay depending on this setting.
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
After you unplug and plug the power cord in while the unit is in standby mode and also the power is being
supplied to a terminal board, the unit will start supplying the power to the board with time delay according
to the setting.
The power indicator lights up red rst and it turns orange when the power starts being supplied to the board.
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
button is pressed.
Note: When “DAY/TIME SETUP” is not set, the clock is not displayed even if
“Clock Display” is “On” (see page 36)
10:00
All Aspect
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of
button, the aspect changes in the selected mode.
Off: Default aspect mode
On: All Aspect mode
Aspect mode of each setting is as follows:
(Example: HD signal)
Off
4:3H-FILLZOOMFULLJUST
On
4:3 (1)4:3 (2)4:3 FullZoom1Zoom2Zoom316:914:9Just1Just2
Auto Setup
Sets the operational mode of the automatic position adjustment in the POS./SIZE menu.
Manual: Automatic position adjustment starts when
is pressed on the remote control or automatic position
adjustment is executed from the POS./SIZE menu.
Auto:
Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
Rotate
Advanced Motion
Resolution
Power On Message
(No activity power
off)
58
Off: Does not rotate the image.
On: Rotates the image 180 degrees.
Note: During the image is rotated, the 3D images are displayed as 2D images.
Displays motion picture images at higher resolution.
On
Off
Notes:
• Please set to “Off” if images look unnatural.
• This function is disabled during 3D images.
Whether to show/hide No activity power off Precautions at the time of power ON is set.
On: The warning precautions are shown at the time of power ON.
Off: The warning precautions are not shown at the time of power ON.
Note: This setting is enabled only if “NO ACTIVITY POWER OFF” is “ENABLE” (see page 47).
Options Adjustments
Item
Adjustments
3D Safety Precautions show/hide is set during power ON.
On: 3D Safety Precaution is shown every time when the power is ON.
Off: 3D Safety Precaution is not shown when the power is ON.
When the setting changes from “On” to “Off”, the conrmation screen is displayed as below.
Pressing “YES” switches the setting.
3D Safety Precautions
3D Safety Precautions
If Off is selected, the 3D safety precautions
will not be displayed when power is turned on.
Change Setting?
YES
NO
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the
button on main unit together with
button on the remote control and hold for more than 5 seconds. The
“Shipping” menu is displayed and the lock is released when it disappears.
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note:
Before setting Weekly Command Timer, set DAY/TIME SETUP. (see page 36)
1
2
Press to select Function.
Press to select “On”.
Note:
• When Function is set to On, ON/OFF TIMER
SETUP (see page 36) is unavailable and
INTERVAL / TIME OF DAY in MODE of
SCREENSAVER (see page 39) cannot be
selected.
Press to select a day.
Press to select a program number.
Note:
• You can set the program from 1 to 7.
--- indicates unset.
Options
1/3
Weekly Command Timer
Audio input select
Input Search
On
Onscreen display
Press ACTION ( ) button
Weekly Command Timer
Function
On
Monday
Tuesday
Program1
Program3
Wednesday
Thursday
Friday
Saturday
Sunday
Program Edit
--Program3
--Program6
Program4
Program number
3
Press to select Program Edit.
Press to show the Program Edit screen.
4
Press to select Program.
Press to change the program numbers (1-7).
y
Thursday
Friday
Saturday
Sunday
Program Edit
Program3
--Program6
Program4
Program Edit screen
1/8
Weekly Command Timer
Program
8:00
01
10:30
02
--:-03
--:-04
--:-05
12:00
06
9:12
07
--:-08
1
PON
IMS:SL1
------DAM:ZOOM
AVL:10
---
59
Options Adjustments
Press to select a command number.
5
Press to show the previous / next command
pages (1-8) of the selected program.
Press to show the command setting screen.
1/8
Weekly Command Timer
Program
01
02
03
04
05
06
07
08
1
8:00
10:30
PON
IMS:SL1
--:--
---
--:--
---
--:--
---
12:00
9:12
--:--
DAM:ZOOM
AVL:10
---
8/8
Weekly Command Timer
Program
57
58
59
60
61
62
63
64
1
20:00
AVL:00
20:30
22:00
DAM:NORM
POF
--:--
---
--:--
---
--:--
---
--:--
---
--:--
---
Command (--- indicates unset)
Set time of timer (--:-- indicates unset)
Command numbers
6
Press to select Command No.
Press to select a command number.
Command setting screen
Weekly Command Timer
Program
1
Command No
Time
Command
7
Press to select Time / Command.
02
10:30
IMS:SL1
Weekly Command Timer
1
Program
Press to set each item.
02
Command No
Time: Set the time to execute a command program.
10:30
Time
Pressing “ ” or “ ” button once changes “Time” 1
IMS:SL1
Command
minute.
Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command: Select a command to execute at the set time. This unit has 64 commands to set.
(see page 67)
Notes:
• Command is performed in order of execution time, regardless of the command number.
• If a command execution time overlaps with that of other commands, these commands are
performed in number order.
• Pressing , Time becomes --:-- and Command becomes ---.
Note:
Press
60
to return to the previous screen.
Options Adjustments
Audio input select
Set up the sound when an image input is selected.
Options
1/3
Weekly Command Timer
Audio input select
Input Search
Onscreen display
On
Press ACTION ( ) button
Audio input select
Press to select image input.
Press to select audio input.
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
SLOT INPUT
VIDEO/COMPONENT
VIDEO/COMPONENT
HDMI
DVI/PC
DVI/PC
NETWORK
Image input
[SLOT INPUT]*1
[VIDEO]
[COMPONENT]*2
[HDMI]
[DVI]
[PC]
[NETWORK]
Audio input
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / HDMI / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
VIDEO/COMPONENT: Sound input for both VIDEO and COMPONENT.
DVI/PC: Sound input for both DVI and PC.
NO AUDIO: No audio input (Mute)
*1 “SLOT INPUT” is displayed when a Terminal Board is installed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.
(see page 52)
When a Terminal Board with dual input terminals is installed
“SLOT INPUT” is displayed as “SLOT INPUT A” and “SLOT INPUT B” and independent settings are available.
To set other image inputs, you can select “SLOT INPUT A” and “SLOT INPUT B”.
Image input
Audio input
[SLOT INPUT A]
[SLOT INPUT B]
[VIDEO]
[COMPONENT]
[HDMI]
[DVI]
[PC]
[NETWORK]
SLOT INPUT A / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / HDMI / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
When Image input and Audio input differ from each other, the Audio input is displayed as below.
PC
FULL
COMPONENT
NANODRIFT
Notes:
• HDMI Audio is selectable only for HDMI Input.
• You cannot set audio of B for SLOT INPUT A, or audio of A for SLOT INPUT B.
61
Options Adjustments
Input Search
When a signal is not detected, another input with a signal is automatically selected.
Options
1/3
Weekly Command Timer
Audio input select
Input Search
Press ACTION ( ) button
1 select
Input Search
2 adjust
Input Search
Primary Input
Secondary Input
Off
Input Search
Off: When there is no signal, the input is not switched automatically.
All Inputs: Searches all inputs and switches to an input with a signal.
Input search is executed in the following order.
(Example) When the current input is PC
PC
NETWORK
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
Priority: Searches “Primary Input” and “Secondary Input” in order and switches to an input with a signal.
SEARCHING
“SEARCHING” is displayed during the input search.
Primary Input, Secondary Input
Set the input to search when “Priority” is selected.
SLOT INPUT*
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
(NONE)
* “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
Notes:
• This menu is available only when “Input lock” is “Off”. (see page 57)
• If the input is changed by this function, the last input is selected when the power is turned on next time.
If you wish to retain the original input when the power is turned on, set “Initial input” to the original input. (see page 56)
62
Troubleshooting
• When there is any abnormality in the electronic pen, see “Electronic
Pen Operations” of the Operating Instructions.
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Sound
Checks
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Volume
(Check whether the mute function has been activated on the remote control.)
Check if speakers are connected properly.
Not plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
Interference
Noisy Sound
Normal Picture
No Sound
No Picture
No Sound
No Picture
Normal Sound
If a signal with a non-applicable color system format, or frequency is input, only the input
terminal indication is displayed.
No Color
Normal Sound
Color controls set at minimum level. (see page 29, 30)
COLOR SYSTEM (see page 53)
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where the
image is missing appear when I use the zoom function.
I can hear sounds coming from inside the unit.
Check whether the batteries have discharged completely and, if they have not, whether they
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong uorescent light.
Check whether the remote control designed specically for use with the unit is being used.
(The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing
very slight contractions in response to changes in the room temperature. There are no adverse
effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a screen wider than one in
the 16:9 mode, blank areas separate from the images are formed at the top and bottom of the screen.
When the power is turned on, a sound of the display panel being driven may be heard: This is
normal and not indicative of malfunctioning.
Parts of the unit become hot.
Even when the temperature of parts of the front, top and rear panels has risen, these temperature
rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly.
Check the settings of “PC POWER MANAGEMENT”, “DVI-D POWER MANAGEMENT”, “NO
SIGNAL POWER OFF” and “NO ACTIVITY POWER OFF” in the SETUP menu. Any of them
may be set to “ON (ENABLE)”. (see page 44, 47)
Power indicator is blinking in red.
There is possibility of malfunction. Please contact an Authorized Service Center.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input
signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
Check
The screen darkens slightly when bright pictures with
minimal movements are shown.
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power
has been turned on, when the input has been switched.
Due to the characteristics of the system used to drive the panel, the edges may appear to icker
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
It takes a while for the picture to appear.
The edges of the images icker.
The brightness on both sides of images in 4:3 mode
changes.
Some parts of the screen do not light up.
Image retention appears
Whirring sounds can be heard from the display unit.
When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides
may change depending on the kind of program shown: This is normal and not indicative of
malfunctioning.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images
displayed in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from xed image use is not
an operating defect and as such is not covered by the Warranty.
This product is not designed to display xed images for extended periods of time.
The display unit is tted with a cooling fan to dissipate heat generated during normal use. The
whirring sound is caused by rotation of the fan and is not a malfunction.
63
List of Aspect Modes
Aspect mode
All Aspect: Factory setting
On
All Aspect: Off
16:9
14:9
FULL
JUST
JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally
so that the picture distortion is minimized. The left and right
edges of the pictures are cut off. The display of the areas
around the left and right edges of the screen is slightly
elongated.
4:3
4:3 (1)
4:3
H-FILL
Zoom
ZOOM
Zoom1
Zoom2
Zoom3
64
The display of the pictures lls the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are
enlarged horizontally, and displayed. This mode is suited to
displaying anamorphic pictures with a 16:9 aspect ratio.
Pictures with a 4:3 aspect ratio are enlarged horizontally
so that the picture distortion is minimized. The display of
the areas around the left and right edges of the screen is
slightly elongated.
4:3
4:3 Full
Description
–
Just1
4:3 (2)
Enlarged screen
Letterbox pictures with a 14:9 aspect ratio are enlarged
vertically and horizontally so that their display lls the
screen vertically and is slightly smaller than the screen
horizontally. The top and bottom edges of the pictures are
cut off. Side panels are displayed at the left and right edges
of the screen.
Just
Just2
Picture
Pictures with a 4:3 aspect ratio are displayed with their
original aspect ratio. Side panels are displayed at the left
and right edges of the screen.
Pictures with a 4:3 aspect ratio are displayed with their
original aspect ratio. The left and right edges of the pictures
are masked by side panels.
Pictures with a 4:3 aspect ratio are enlarged horizontally so
that their display lls the screen. The left and right edges of
the pictures are cut off.
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display lls the screen.
The top and bottom edges of the pictures are cut off.
ZOOM
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display lls the screen.
The top and bottom edges as well as the left and right edges
of the pictures are cut off.
–
Letterbox pictures with a 2.35:1 aspect ratio are enlarged
vertically and horizontally so that their display lls the screen
vertically and is slightly larger than the screen horizontally.
The top and bottom edges as well as the left and right edges
of the pictures are cut off.
Applicable Input Signals
*Mark: Applicable input signal
Horizontal frequency
(kHz)
525 (480) / 60i
15.73
525 (480) / 60p
31.47
625 (575) / 50i
15.63
625 (576) / 50i
15.63
625 (575) / 50p
31.25
625 (576) / 50p
31.25
750 (720) / 60p
45.00
750 (720) / 50p
37.50
1,125 (1,080) / 60p
67.50
1,125 (1,080) / 60i
33.75
1,125 (1,080) / 50p
56.26
1,125 (1,080) / 50i
28.13
1,125 (1,080) / 24sF
27.00
1,125 (1,080) / 30p
33.75
1,125 (1,080) / 25p
28.13
1,125 (1,080) / 24p
27.00
1,250 (1,080) / 50i
31.25
27.00
2,048 &times; 1,080 / 24sF 7
2,048 &times; 1,080 / 24p 7
27.00
640 &times; 400 @70 Hz
31.46
640 &times; 480 @60 Hz
31.47
640 &times; 480 @72 Hz
37.86
640 &times; 480 @75 Hz
37.50
640 &times; 480 @85 Hz
43.27
800 &times; 600 @56 Hz
35.16
800 &times; 600 @60 Hz
37.88
800 &times; 600 @72 Hz
48.08
800 &times; 600 @75 Hz
46.88
800 &times; 600 @85 Hz
53.67
852 &times; 480 @60 Hz
31.47
1,024 &times; 768 @50 Hz
39.55
1,024 &times; 768 @60 Hz
48.36
1,024 &times; 768 @70 Hz
56.48
1,024 &times; 768 @75 Hz
60.02
1,024 &times; 768 @85 Hz
68.68
1,066 &times; 600 @60 Hz
37.64
1,152 &times; 864 @60 Hz
53.70
1,152 &times; 864 @75 Hz
67.50
1,280 &times; 768 @60 Hz
47.70
1,280 &times; 800 @60 Hz (1)
49.31
1,280 &times; 800 @60 Hz (2)
49.70
1,280 &times; 960 @60 Hz
60.00
1,280 &times; 960 @85 Hz
85.94
1,280 &times; 1,024 @60 Hz
63.98
1,280 &times; 1,024 @75 Hz
79.98
1,280 &times; 1,024 @85 Hz
91.15
1,366 &times; 768 @50 Hz
39.55
1,366 &times; 768 @60 Hz
48.36
1,400 &times; 1,050 @60 Hz
65.22
1,440 &times; 900 @60 Hz (1)
55.47
1,440 &times; 900 @60 Hz (2)
55.93
1,600 &times; 1,200 @60 Hz
75.00
1,600 &times; 1,200 @65 Hz
81.25
1,920 &times; 1,080 @60 Hz
67.50
1,920 &times; 1,200 @60 Hz
74.04
Macintosh13” (640 &times; 480)
35.00
Macintosh16” (832 &times; 624)
49.72
Macintosh21” (1,152 &times; 870)
68.68
Signal name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Vertical frequency
(Hz)
59.94
59.94
50.00
50.00
50.00
50.00
60.00
50.00
60.00
60.00
50.00
50.00
48.00
30.00
25.00
24.00
50.00
48.00
24.00
70.07
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
59.94
50.00
60.00
70.07
75.03
85.00
59.94
60.00
75.00
60.00
59.91
59.81
60.00
85.00
60.02
75.03
85.02
50.00
60.00
60.00
59.90
59.89
60.00
65.00
60.00
59.95
66.67
74.54
75.06
COMPONENT / RGB IN / PC IN
DVI-D IN
(Dot clock (MHz))
(Dot clock (MHz))
* (13.5)
* (27.0)
* (27.0) 5
* (27.0)
* (13.5)
* (27.0)
* (27.0)
* (27.0)
* (74.25)
* (74.25)
* (74.25)
* (74.25)
* (148.5) 1
* (148.5)
* (74.25) 1
* (74.25)
* (148.5) 1
* (148.5)
* (74.25)
* (74.25) 1
* (74.25) 2
* (74.25) 1
* (74.25)
* (74.25)
* (74.25) 1
* (74.25) 1
* (74.25)
* (74.25) 3
*
*
*
*
*
*
*
*
*
*
*
(25.17)
(25.18)
(31.5)
(31.5)
(36.0)
(36.0)
(40.0)
(50.0)
(49.5)
(56.25)
(33.54)
*
*
*
*
*
(65.0)
(75.0)
(78.75)
(94.5)
(53.0)
*
*
*
*
*
*
*
*
*
(108.0)
(80.14)
(71.0)
(83.5)
(108.0)
(148.5)
(108.0)
(135.0)
(157.5)
6
6
* (86.71)
*
*
*
*
*
(88.75)
(106.5)
(162.0)
(175.5)
(148.5)
4
HDMI
*
*
*
*
*
*
*
*
*
*
*
* (25.18)
*
* (40.0)
*
* (34.24)
* (51.89)
* (65.0)
*
*
*
* (53.0)
* (81.62)
*
*
* (71.0)
* (83.5)
*
*
* (108.0)
*
*
*
*
*
*
*
*
*
*
*
*
*
(69.92)
(87.44)
(122.61)
(88.75)
(106.5)
(162.0)
* (148.5)
* (154.0)
*
*
* (30.24)
* (57.28)
* (100.0)
1: Based on SMPTE 274M standard.
2: Based on SMPTE RP211 standard.
3: Based on SMPTE 295M standard.
4: The input signal is recognized as 1,125 (1,080) / 60p.
5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60Hz signal.
6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal Board
(TY-FB11DHD) is installed.
Note: Signals without above specication may not be displayed properly.
65
Applicable Input Signals
Video input (VIDEO)
Signal name
1
2
3
4
5
NTSC
PAL
PAL60
SECAM
Modied NTSC
Horizontal
frequency(kHz)
15.73
15.63
15.73
15.63
15.73
Vertical
frequency(Hz)
59.94
50.00
59.94
50.00
59.94
Shipping condition
This function allows you to reset the unit to the factory setting.
1
2
Press to display the SETUP menu.
Press to select “OSD LANGUAGE”.
Press for more than 3 seconds.
3
Press to select “Shipping”.
Press to display the Shipping menu.
4
SETUP
1/2
TOUCH-PEN MODE
3D SETTINGS
SIGNAL
SCREENSAVER
EXTENDED LIFE SETTINGS
ECO MODE SETTINGS
INPUT LABEL
FUNCTION BUTTON SETTINGS
COMPONENT/RGB-IN SELECT
RGB
NO ACTIVITY POWER OFF
DISABLE
30 S
MENU DISPLAY DURATION
5
OSD BRIGHTNESS
OSD LANGUAGE
ENGLISH (US)
Options
Shipping
Press to select “YES”.
Shipping
YES
Press to conrm.
5
Wait for 10 seconds.
6
Press the power switch (
) on main unit to turn the power off.
[from the unit]
1 Press the MENU button till the SETUP menu is displayed.
2 Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3 Press and hold the ENTER button till the Shipping menu is displayed.
4 Press the Volume Up “+” or Down “–” button to select “YES”.
5 Press the ENTER button and wait for 10 sec.
) on main unit to turn the power off.
6 Press the power switch (
66
NO
Command list of Weekly Command Timer
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Command
AAC:MENCLR
AAC:MENDYN
AAC:MENSTD
AAC:SURMON
AAC:SUROFF
AMT:0
AMT:1
AVL:00
AVL:10
AVL:20
AVL:30
AVL:40
AVL:50
AVL:60
DAM:FULL
DAM:JUST
DAM:NORM
DAM:ZOOM
IMS:SL1
IMS:S1A
IMS:S1B
IMS:VD1
IMS:YP1
IMS:HM1
IMS:DV1
IMS:PC1
IMS:NW1
OSP:SCR0
OSP:SCR1
POF
PON
SSC:FNC0
SSC:FNC1
SSC:MOD0
SSC:MOD3
VMT:0
VMT:1
Control details
Audio Menu (CLEAR)
Audio Menu (DYNAMIC)
Audio Menu (STANDARD)
Surround (ON)
Surround (OFF)
Audio Mute (OFF)
Audio Mute (ON)
Audio Volume (00)
Audio Volume (10)
Audio Volume (20)
Audio Volume (30)
Audio Volume (40)
Audio Volume (50)
Audio Volume (60)
Aspect (FULL)
Aspect (JUST)
Aspect (4:3)
Aspect (ZOOM)
Input select (SLOT INPUT)
Input select (SLOT INPUT A)
Input select (SLOT INPUT B)
Input select (VIDEO)
Input select (COMPONENT)
Input select (HDMI)
Input select (DVI)
Input select (PC)
Input select (NETWORK)
Screen Saver SCROLLING BAR ONLY (OFF)
Screen Saver SCROLLING BAR ONLY (ON)
Power OFF
Power ON
Screen Saver function (SCROLLING BAR ONLY)
Screen Saver function (NEGATIVE IMAGE)
Screen Saver (Mode (OFF))
Screen Saver (Mode (ON))
Picture Mute (OFF)
Picture Mute (ON)
Picture Mute cannot be unlocked by powering off/on with the remote control. Turn off and on again with the button on
the unit or enter the command VMT:0 to unlock Picture Mute.
67
Specications
Power Source
Power Consumption
Rated Power Consumption
Stand-by condition
Power off condition
Plasma Display panel
Screen size
(No.of pixels)
Operating condition
Temperature
Humidity
Applicable signals
Color System
Scanning format
PC signals
Connection terminals
VIDEO
AV IN
AUDIO L-R
HDMI
COMPONENT/RGB IN
Y/G
PB/CB/B
PR/CR/R
AUDIO L-R
DVI-D IN
AUDIO
PC IN
TH-65PB1U
110 - 127 V AC, 50/60 Hz
555 W
0.4 W
0.2 W
Drive method : AC type 65-inch, 16:9 aspect ratio
56.4” (1,434 mm) (W) &times; 31.7” (806 mm) (H) &times; 64.7” (1,645 mm) (diagonal)
2,073,600 (1,920 (W) &times; 1,080 (H))
[5,760 &times; 1,080 dots]
32 &deg;F - 104 &deg;F (0 &deg;C - 40 &deg;C)
20 % - 80 %
NTSC, PAL, PAL60, SECAM, Modied NTSC
525 (480) / 60i &middot; 60p, 625 (575) / 50i &middot; 50p, 750 (720) / 60p &middot; 50p, 1125 (1080) / 60i &middot; 60p &middot; 50i &middot; 50p
&middot; 24p &middot; 25p &middot; 30p &middot; 24sF, 1250 (1080) / 50i
VGA, SVGA, XGA, SXGA
UXGA &middot;&middot;&middot;&middot; (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
BNC
RCA Pin jack &times; 2
1.0 Vp-p (75 )
0.5 Vrms, Shared with COMPONENT/RGB IN
TYPE A Connector
BNC
BNC
BNC
RCA Pin jack &times; 2
DVI-D 24 Pin
Content Protection
Stereo mini jack (M3) &times; 1
High-Density Mini D-sub 15 Pin
Stereo mini jack (M3) &times; 1
External Control Terminal
D-sub 9 Pin
3D IR TRANSMITTER for 3D IR TRANSMITTER (TY-3D30TRW)
3D SHUTTER OUT M3 jack &times; 1
DC 8V OUT
Center plus, for EIAJ 4mm plug
AUDIO
SERIAL
WIRELESS MODULE
LAN
EXT SP
with sync 1.0 Vp-p (75 )
0.7 Vp-p (75 )
0.7 Vp-p (75 )
0.5 Vrms, Shared with VIDEO
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
0.5 Vrms, Shared with PC IN
Y or G with sync 1.0 Vp-p (75 )
Y or G without sync 0.7 Vp-p (75 )
PB/CB/B: 0.7 Vp-p (75 )
PR/CR/R: 0.7 Vp-p (75 )
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms, Shared with DVI-D IN
RS-232C compatible
for Wireless module (ET-WM200U)
RJ45 10BASE-T/100BASE-TX, compatible with PJLink™
8 , 20 W [10 W + 10 W] (10 % THD)
Dimensions (W &times; H &times; D)
61.2” (1,554 mm) &times; 36.5” (925 mm) &times; 3.9” (99 mm)
Mass (weight)
main unit only
approx. 132.3 lbs
Note:
Design and specications are subject to change without notice. Mass and dimensions shown are approximate.
68
This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporation,
(2) the software owned by third party and licensed to Panasonic Corporation,
(3) the software licensed under the GNU General Public License, Version 2.0 (GPL-2.0),
(4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL-2.1) and/or,
(5) open source software other than the software licensed under the GPL and/or LGPL.
For the software categorized as (3) and (4), please refer to the terms and conditions of GPL-2.0 and LGPL-2.1, as the
case may be at
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
The GPL/LGPL software is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even
the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
At least three (3) years from delivery of products, Panasonic will give to any third party who contact us at the contact
information provided below, for a charge no more than our cost of physically performing source code distribution, a
complete machine-readable copy of the corresponding source code and the copyright notice, covered under GPL-2.0/
LGPL-2.1.
Contact Information
[email protected]
For the software categorized as (5) includes as follows.
1. The software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
2. The software developed by the University of California, Berkeley and its contributors.
3. FreeType code.
4. The Independent JPEG Group's JPEG software.
5. thttpd code.
USA Only:
Disposal may be regulated in your community due to environmental considerations. For disposal or recycling
information, please visit Panasonic website:
http://www.panasonic.com/environmental or call 1-888-769-0149.
Customer’s Record
The model number and serial number of this product can be found on its back cover. You should note this serial number
in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase
to aid in identication in the event of theft or loss, and for Warranty Service purposes.
Model Number
&curren; Panasonic Corporation 2012
Panasonic System Communications Company of North America
Unit of Panasonic Corporation of North America
Executive Ofce :
Three Panasonic Way 2F-5, Secaucus, NJ 07094
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
Serial Number
">
Hello! I am an AI chatbot specifically trained to assist you with the Panasonic TH-65PB1U touch screen monitor Operating instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Assistant typing
Assistant terminated
Related

Panasonic TH85PB1U Flat Panel Television User manual

Panasonic TH50PB2U Flat Panel Television User manual

Panasonic TH-65PB1 Owner Manual

Panasonic TH-50BT300W Flat Panel Television Operating instructions

Panasonic Interactive Plasma Display TH-85PB1W, TH-103PB1W Operating Instructions

Panasonic TH65PB1EK Operating Instructions

Panasonic TH-50PB2W Flat Panel Television User manual

Panasonic TH50PF30E Operating Instructions

Panasonic TH-50PH30E Plasma TV Operating Instructions

Panasonic VX300 TH-65VX300ER Operating Instructions

Panasonic TH-65PF9UK Operating Instructions

Panasonic TH-65PB1U Operating Instructions
