Amer Networks SD7FX1SC network switch Specification

Add to my manuals
13 Pages

advertisement

Amer Networks SD7FX1SC network switch Specification | Manualzz

Installation GGuide

SD7FX1SC

10/100 Fast Ethernet Switch with 100FX Connectivity

FCC NOTICE

This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including the interference that may cause.

CE NOTICE

Marking by the symbol indicates compliance of this equipment to the EMC directive of the European Community. Such marking is indicative that this equipment meets or exceeds the following technical stan dards:

EMC Class B

EN 50081-1/1992 : EN55022, EN61000-3-2, EN61000-3-3

EN 50082-1/1998 : EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5,

EN61000-4-6, EN61000-4-8, EN61000-4-11

Copyright ((C) All Rights Reserved.

Table of Contents

1. Introduction ............................................................................1

1.1 Features ...............................................................................2

1.2 Specifications ........................................................................4

2. Installing the Switch .............................................................5

2.1 Unpacking ..............................................................................5

2.2 Checking AC Power ................................................................5

2.3 Installing the Switch ................................................................5

3.Making Network Connections .....................................................6

3.1 Switched Ports .......................................................................6

3.2 Making UTP Connections ......................................................6

3.3 Making Fiber Connection ........................................................8

4. LED Indicators ....................................................................9

4.1 LED Panel ............................................................................9

4.2 Interpretation ..........................................................................9

1. Introduction

This 8-port Fast Ethernet switch provides seven 10/100 RJ45 ports and one 100BASE-FX fiber port, each capable of transmitting or receiving information simultaneously at full wire speed to control and allocate the network bandwidth.

The key features of the switch series are:

Optimized Bandwidth : Combining eight 100Mbps-based Fast

Ethernet switched ports, the switch delivers a high network bandwidth for your Fast Ethernet network

Easy Migration : With 10BASE-T support on 10/100 port, the switch provides a non-disruptive and smooth migration path from

Ethernet to a Fast Ethernet network.

Fiber Uplink Support : With 100BASE-FX port, the switch provides a connectivity to a Fast Ethernet network via fiber cable.

Easy Installation : With the functions of auto-speed-sensing and auto-negotiation on each port, the switch supports plug-and-play installation which eliminates configuration problems.

-1-

1.1 Features

Designed for resolving congestion problems caused by bandwidth-hungry devices and bandwidth-intensive applications as well as a high number of users, the switches not only adhere to the IEEE 802.3 10BASE-T,

802.3u 100BASE-TX and 100BASE-FX standards, but also feature:

• Seven 10/100BASE-TX auto-negotiation switched ports and one

100BASE-FX port for flexible connections to desktop PCs, servers and Fast Ethernet devices.

• The 10/100BASE-TX switched ports support:

auto-negotiation with auto-negotiation devices

full-duplex or half-duplex operation

automatic MDI/MDI-X configuration

• For the 100BASE-FX fiber port, the switch series support variety of fiber connectors for different application needs. The fiber connectors include ST, SC, MT-RJ, and VF-45 types for multimode and single mode fiber cables.

• Supports duplex mode selector for the 100BASE-FX fiber port.

• Self learning for active MAC addresses and address aging

• Store and forward switching to ensure only good packets are forwarded

• Forwarding and filtering at full wire speed

• Supports IEEE 802.3x flow control for full-duplex operation

• Supports back-pressure flow control for half-duplex operation

• Comprehensive LED indicators provide quick, easy to read port and switch information

-2-

1.2 Specifications

10/100 Ports

100FX Port

Flow control

Cables

LED indicators

Forwarding rate

Filtering address

MAC address

Aging time

Environment

Dimensions

DC IN Jack

DC IN voltage

Consumption

IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX std.

Shielded RJ-45 jacks with Auto MDI-X detection

Auto-negotiation capable

Speed for 10Mbps or 100Mbps

Full-duplex or half-duplex mode support

IEEE 802.3u 100BASE-FX compliant

Fixed 100Mbps operation

Duplex mode selector - full duplex or half duplex

IEEE 802.3x pause packet for full duplex operation

Back-pressure for half duplex operation

10BASE-T Cat. 3, 4, 5 or higher (100 meters max.)

100BASE-TX Cat. 5, 5e or higher (100 meters max.)

100BASE-FX multimode or single mode fiber cable

Power status

Per port : Speed, Link, Activity, Duplex, Collision status

14,880 pps for Ethernet (10M)

148,800 pps for Fast Ethernet (100M)

Multicast/Broadcast/Unicast address

1K entries

300 seconds

Temperature -5 o C to 40 o C

Relative humidity 10% to 90% non-condensing

180 mm x 114 mm x 26 mm (WxDxH)

7.08 x 4.49 x 1.02 inch

Rating +7.5V/1A, D6.3mm D2.0mm

Operating +6.0V ~ +12.6VDC (Device DC Input)

DC input power consumption 3.5W @+7.5V

-3-

100FX Port Fiber Specifications

Model Ext

-T

-C

-JM

-VM

-SA2

-SL2

-SL3

-SL4

-SL6

-SL7

-SL9

-SL10

-SL12

SC

SC

SC

SC

SC

SC

SC

Fiber Wavelength Tx Power

ST MMF 1310nm -19 ~ -14dBm

Sens. Ref.Distance

-31dBm 2km

SC MMF 1310nm -19 ~ -14dBm -31dBm 2km

MT-RJ MMF 1310nm -19 ~ -14dBm -31dBm 2km

VF-45 MMF 1310nm -20 ~ -14dBm -31dBm 2km

SC

SC

SMF 1310nm -15 ~ -8dBm -31dBm 20km

SMF 1310nm -15 ~ -8dBm -32dBm 20km

SMF 1310nm

SMF 1310nm

SMF 1310nm

-15 ~ -8dBm

-5 ~ 0dBm

-5 ~ 0dBm

-34dBm

-34dBm

-35dBm

30km

40km

60km

SMF 1310nm -3 ~ +3dBm -37dBm 70km

SMF 1310nm 0 ~ +5dBm -37dBm 90km

SMF 1550nm -3 ~ +3dBm -37dBm 100km

SMF 1550nm 0 ~ +5dBm -37dBm 120km

Ref. Distance : reference distance when operating on full duplex mode

MMF : Multimode fiber - 62.5/125

µ m, 50/125

µ m

SMF : Single Mode fiber - 9/125

µ m

Single Fiber Bi-Di WDM Series

Model Ext

-W3515

-W5315

-W3540

Fiber Wavelength Tx Power

Rx 1310nm

SC SMF Tx 1310nm -8 ~ 0dBm

Sens. Ref.Distance

SC SMF Tx 1310nm -14 ~ -8dBm -31dBm 15-20km

Rx 1550nm

SC SMF Tx 1550nm -14 ~ -8dBm -31dBm 15-20km

-34dBm 40km

-W5340

Rx 1550nm

SC SMF Tx 1550nm -8 ~ 0dBm

Rx 1310nm

-34dBm 40km

Single Mode CWDM Series

Model Ext

-CxxW40

-CxxW80

Fiber Wavelength Tx Power Sens. Ref.Distance

SC SMF Tx 1xx0nm -5 ~ 0dBm -35dBm 40km

Rx 1100-1650nm

SC SMF Tx 1xx0nm 0 ~ +5dBm -37dBm

Rx 1100-1650nm

80km

Tx 1xx0nm : 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610nm

-4-

2. Installing the Switch

2.1 Unpacking

Check to see that you have everything before you start the installation.

• Installation guide

• The switch unit

• One AC power adapter for the unit

2.2 Checking AC Power

Before you begin the installation, check the AC voltage of your area. The

AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area.

The specifications of the AC power adapter are:

• AC input power: AC power voltage of your area

• DC output power: +7.5VDC 1A min.

• DC plug type:

The DC power jack for the AC power adapter is located on the rear of the switch as shown below:

2.3 Installing the Switch

1. Use the AC power adapter provided only.

2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet.

-5-

3. Making Network Connections

3.1 Switched Ports

The following figure shows the locations of the switched ports:

3.2 Making UTP Connections

10/100 TP Port Configuration

All 10/100 TP ports support configuration as follows:

Auto-negotiation capable

Highest capability : 100M Full duplex

Speed : auto-sensing for 100Mbps or 10Mbps

Duplex : Full duplex, Half duplex

Auto MDI-X function

The following table lists the configuration used for the 10/100 port when it connects to different devices:

Connected Device

10BASE-T hub port

100BASE-TX hub port

Auto-negotiation port

Configuration Used

10Mbps, half-duplex

100Mbps, half-duplex

Determined via auto-negotiation process

Non-auto*1 half-duplex port auto-speed-sensing *2, half-duplex

Non-auto full-duplex port Not supported

*1 Non-auto : non-auto-negotiation

*2 speed is determined by auto-sensing function

-6-

Cables

Depending on the connection speed, use the proper UTP cables:

Speed Cables used

100M

10M

Cat. 5, 5e, or higher grade

Distance

100 meters

Cat. 3, 4, 5, 5e, or higher grade 100 meters

Auto-MDI-X Function

An Auto-MDI-X function will automatically detect if a crossover is required and make the swap of Tx pair and Rx pair internally. With this function, straight-through cable can be used for any connection. MDI to

MDI-X connection rule is not necessary anymore. In the switches, all TP ports are equipped with this function. You can use just straight-through type of cables for all your connections.

3.3 Making Fiber Connection

For different fiber connections, several alternative models can be selected for different fiber connections. Refer to Section 1.2 for the model selection. The following figure illustrates a connection example between two SC fiber ports:

-7-

100FX Duplex Selector

This selector is used for 100FX port duplex mode selection as follows:

The following table lists the maximum MM fiber cable length connecting to different devices:

Connected Device

Network card half-duplex fiber port

Network card full-duplex fiber port

Class I hub half-duplex fiber port

2 Class II hub half-duplex fiber port

Switched half-duplex fiber port

Switched full-duplex fiber port

Distance (MMF cable)

400 m

2 km

160 m

112 m

400 m

2 km

-8-

4. LED Indicators

4.1 LED Panel

The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the switch as illustrated below:

4.2 Interpretation

LED Functions

POWER LED : indicates the power status of the switch.

LNK/SPD/ACT LED : indicates the link status, connection speed

DUP/COL LED : status, and traffic status of the switched port indicates the duplex status and collision status of the switched port

LED States and Indications

LED

POWER

POWER

State & Color Indication

Off -------No power is supplied to the switch.

On Green Power is being supplied to the switch.

LNK/SPD/ACT On Green Speed 100M, link up

LNK/SPD/ACT On Amber Speed 10M, link up

LNK/SPD/ACT Blink Green Speed 100M, link up, Tx/Rx activities

LNK/SPD/ACT Blink Amber Speed 10M, link up, Tx/Rx activities

LNK/SPD/ACT Off -------Link down

DUP/COL On Green

DUP/COL Off --------

DUP/COL Blink Green

Full duplex mode

Half duplex mode, no collision

Half duplex mode, collisions

-9-

Contact Information

For technical support: [email protected]

For product information: info@@amer.com

http://www.amer.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals