PC- ART : Setting A 7 Day Time Schedule
Technical Data Sheet
PC- ART : Setting A 7 Day Time Schedule
 To set the weekly timer function on the controller firstly switch the controller off using the
“RUN/STOP” button
 Next press the “TIMER” button once.
Press The “TIMER” Button To
Enter Setting Mode

SET
1 2 3 4 S & SCHEDULE are now displayed with “1” flashing.
Hitachi Air Conditioning Europe SAS.
Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA
Tel: 01628 585393, Fax: 01628 585500
Email: [email protected]
Technical Data Sheet
 Press The “
OK ” button and the first time pattern can be set.
 The hour segment will now flash; using the “DAY” (down) or “SCHEDULE” (up) scroll to
the desired “ ON ” time; press the “
OK ” to confirm.
 Next the minute segment will flash, scroll to desired time using “DAY” (down) or
“SCHEDULE” (up) again press the “
OK ” to confirm.
 Next repeat the process to input the desired “ OFF ” time.
 When this is complete press the “
OK ” to confirm time patterns.
 If a further schedule is required press the “SCHEDULE” button so “2” is flashing. This is
set using same procedure as setting the first schedule.
 Schedule patterns can be reviewed by pressing the “SCHEDULE” button. When an error
has been made press the “
OK ” and new times can be inputted, alternatively the
times can be cancelled by pressing the “RESET” button (time will revert to - - : - - ).
 The “S” schedule is used for energy saving mode this will increase the dead-band on
the heating or cooling mode. If this is required, set the time as before, then select the
temperature dead –band to 3oC or 5oC.
Hitachi Air Conditioning Europe SAS.
Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA
Tel: 01628 585393, Fax: 01628 585500
Email: [email protected]
Technical Data Sheet
 When all the time patterns have been set press the “TIMER” button to exit this setting
screen.
 The desired patterns now need to be applied to the required days of operation, to do this
press the “TIMER” button and hold for 3 seconds.
 The days of the week appear with current day and schedule “1” flashing.
 Next press the “DAY” button and days will flash in the following sequence (see table
below) when the desired days are flashing press the “
OK” button to confirm.
No. Of Times “DAY” Button Is
Pressed
1
“Mon”
2
“Tue”
3
“Wed”
4
“Thu”
5
“Fri”
6
“Sat
7
“Sun”
8
“Mon” “Tue” “Wed” “Thu” “Fri” “Sat” “Sun”
9
“Mon” “Tue” “Wed” “Thu” “Fri”
10
“Sat” “Sun”
 “SCHEDULE” now appears above the OFF time (timer can also be removed by
pressing the “
OK” button and the “SCHEDULE” display is removed): timer is now
set.
Hitachi Air Conditioning Europe SAS.
Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA
Tel: 01628 585393, Fax: 01628 585500
Email: [email protected]
Technical Data Sheet
 If more than one schedule has been set press the “SCHEDULE” button to scroll to next
set schedule, the days of the week are selected as before and it is set by pressing the “
OK” button.
 When all the time schedules have been applied press and hold the “TIMER” button to
exit the setting mode.
 The display should show “NEXT SCHEDULE” with the (next) “ ON ” or “ OFF “ time.
 To disable the schedules press the “SCHEDULE” button and hold for three seconds.
 “NEXT SCHEDULE” will now flash and timer is disabled; to enable again press and hold
the “SCHEDULE” button.
Hitachi Air Conditioning Europe SAS.
Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA
Tel: 01628 585393, Fax: 01628 585500
Email: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement