NETGEAR N750 Wireless Dual Band Gigabit ADSL Modem Router

NETGEAR N750 Wireless Dual Band Gigabit ADSL Modem Router
Technical Support
Package Contents
Thank you for selecting NETGEAR products.
The box should contain the following items. If any items are
incorrect, missing, or damaged, contact your NETGEAR dealer.
After installing your device, locate the serial number on the label
of your product and use it to register your product at Registration is required before you can
use the telephone support service. Registration through our
website is strongly recommended.
Go to for product updates and web support.
N750 Wireless Dual Band Gigabit ADSL
Modem Router
DGND4000 Premium Edition
Installation Guide
Ethernet cable
Modem Router
Power adapter (2 parts)
350 East Plumeria Drive
San Jose, CA 95134, USA
July 2012
Telephone cable
You can use this diagram to connect your modem router to ADSL (1a) or cable/fiber (1b), or you can follow the
instructions in this booklet.
1a: For ADSL
Declarations of Conformity
For complete DoC please visit the NETGEAR EU Declarations of Conformity
website at
This symbol is placed in accordance with the European Union
Directive 2002/96 on the Waste Electrical and Electronic Equipment
(the WEEE Directive). If disposed of within the European Union, this
product should be treated and recycled in accordance with the laws of
your jurisdiction implementing the WEEE Directive.
2. Computer
For indoor use only in all EU countries and Switzerland.
3. Power
1b: For cable/fiber
4. Browser
2.4 GHz
Wireless LED
Cable/fiber modem
Open browser and follow
instructions for installation
Note: A user manual is available online at or through a link in the modem router’s user interface.
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Install Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Preset Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wireless Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Add Wireless Devices to the Network . . . . . . . . . . . . . . . . . . . . 8
WPS Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Manual Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Access the N750 Router to Make Changes . . . . . . . . . . . . . . . 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
NETGEAR genie App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NETGEAR genie Mobile App . . . . . . . . . . . . . . . . . . . . . . 14
ReadySHARE Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ReadySHARE Cloud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ReadySHARE Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Control Center Configuration . . . . . . . . . . . . . . . . . . . . . . 18
USB Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Scan with a Multifunction Printer . . . . . . . . . . . . . . . . . . . 20
Time Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Other Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Before You Begin
You can connect directly to a DSL line or to a cable/fiber modem.
Note: If you are connecting to a DSL line, make sure that your DSL
service is active before you install the modem router. You need the
information listed here to install your DSL modem and connect to the
Internet. Locate it and have it on hand before you start the installation
DSL user name and password. These are included in the
welcome letter your DSL ISP sent you when you signed up for
your service. Record your DSL Internet service account user
name and password here:
User name:
Your telephone number or DSL account number. If you do not
have voice service, you can use your DSL account number in
place of a phone number.
If you do not know or cannot locate your user name and
password, call your DSL Internet service provider.
Be specific when speaking with your DSL Internet service
provider. For example, you could say:
I need my DSL service user name and password. Can you help
Note: If your provider says that they do not support NETGEAR
devices, tell them you need only your DSL user name and
password; you do not need support.
Install Your Modem Router
Note: Keep your modem router in a vertical position.
To install your modem router:
1. Connect to the Internet with ADSL or Ethernet WAN.
You can connect either directly to a DSL line or to a cable/fiber
a. Connect to ADSL (if connecting directly to a DSL line).
Install an ADSL microfilter between the phone line and the
phone. A microfilter filters DSL interference out of
standard phone equipment that shares the line with the
DSL service. Example devices are telephones, fax
machines, answering machines, and caller ID displays.
Connect the ADSL port of the modem router to the ADSL
port of the microfilter.
Note: Use an ADSL microfilter for every phone line in the
house if your modem router and telephone connect to the
same phone line.
Plugs into ADSL line
b. Connect to cable or fiber (if connecting to a cable/fiber
Cable/fiber modem
2. Cable your computer.
Use an Ethernet cable (not provided).
3. Power on your router.
2.4 GHz
Wireless LED
a. Connect the power adapter to the router, and plug the power
adapter into an outlet.
b. Wait until the 2.4 GHz Wireless LED
4. Open a browser.
The NETGEAR genie installation wizard displays.
turns solid
If you do not see the genie screen, close and reopen the browser,
and enter in the address bar. See
Troubleshooting on page 11.
5. Click Next to allow the genie to help you. Follow the steps to set up
your Internet connection.
Note for DSL: If your DSL Internet service requires a user name
or password, you are prompted to enter this information. If you do
not have this information, contact your Internet service provider
(see Before You Begin on page 2).
Preset Wireless Security
This product has a unique WiFi network name (SSID) and network
key (password). The default SSID and network key (password) are
uniquely generated for every device, like a serial number, to protect
and maximize your wireless security. This information is on the label
on the bottom of the product.
WiFi network name (SSID)
Network key (password)
NETGEAR recommends that you do not change the preset WiFi
network name (SSID) and network key (password). If you do change
the settings, the security SSID and password on the bottom of the
product no longer apply.
Note: Your network names (SSIDs) and passphrases are casesensitive. Your network name, security method, and passphrase need
to be the same for all the wireless devices that are connected to your
router on a network.
Wireless Network Settings
Record the default preset wireless settings that are printed on the
label in the spaces here for easy reference.
2.4-GHz WiFi network name (SSID):
2.4-GHz network key (password):
5-GHz WiFi network name (SSID):
5-GHz network key (password):
If you change the default settings, record them here for easy
reference, and then store this booklet in a safe place:
2.4-GHz WiFi network name (SSID):
2.4-GHz network key (password):
5-GHz WiFi network name (SSID):
5-GHz network key (Password):
To retrieve or update your wireless password, type in a web browser and log in using the
default user name (admin) and password (password).
Select Wireless to locate your wireless passwords.
Add Wireless Devices to the Network
Choose either the manual or Wi-Fi Protected Setup (WPS) method to
add wireless computers and other devices to your wireless network.
WPS Method
If your wireless device supports WPS (Wi-Fi Protected Setup)—
NETGEAR calls this method Push 'N' Connect—you might be
prompted to press the WPS button on the router instead of entering a
password. If this happens:
1. Press the WPS button
on the router.
2. Within 2 minutes, press the WPS button on the client device, or
follow the WPS instructions that came with your wireless device to
complete the WPS process. The device is then connected to your
3. Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a
WEP client to your network using WPS, it does not work.
Manual Method
1. On the wireless device that you want to connect to your router
(iPhone, laptop, computer, gaming device), open the software
utility that manages its wireless connections. This utility scans
for all wireless networks in your area.
2. Look for the preset NETGEAR WiFi network name (SSID) and
select it. The SSID is on the product label on the bottom of the
Note: If you changed the name of your network during the setup
process, look for that network name.
3. Enter the preset password (or your custom password if you
changed it), and click Connect.
Repeat steps 1–3 to add other wireless devices.
Access the N750 Router to Make Changes
After you use NETGEAR genie to set up the router, you can log in to
the router to view its settings or make changes.
To log in to the router:
1. Launch a web browser from a computer or wireless device that
is connected to the router.
2. Type or in the
address field of the browser. A login screen displays:
3. Enter admin for the user name and password for the password.
The NETGEAR genie screen displays:
See the User Manual for more information about the router
To change the password for the router user name:
1. Log in to the router.
2. Select Advanced > Administration > Set Password to display the
Set Password screen:
3. Type your old password, and type the new password twice.
If the browser does not display the web page:
Make sure that the computer is connected to one of the four LAN
Ethernet ports, or wirelessly to the router.
Make sure that the router is fully up and running. Its WiFi LED
should turn on.
Close and reopen the browser to make sure that the browser
does not cache the previous page.
Browse to
If the computer is set to a static or fixed IP address (this is
uncommon), change it to obtain an IP address automatically from
the router.
If the modem router does not power on:
1. Check your cables.
Disconnect and reconnect each cable. There is usually an
audible click when the cable is correctly connected.
See if the telephone cable connecting your DSL modem
router to the wall jack is plugged into a filter. A filter is not
required if you do not have telephone voice service. A filter
that is installed where it is not needed might eliminate your
ADSL signal.
2. Power down your DSL modem router, and then power it up again.
a. Shut down your computer and turn off the modem router.
b. Unplug the power adapter and all other cables from the back
of the DSL modem router.
c. Wait 30 seconds, then reconnect the cables and adapter to
your DSL modem router, and turn it on.
d. Make sure that the router power light is on. If the light is off,
try plugging the adapter into another power outlet.
e. Turn your computer back on, and wait for the indicator lights
to turn green.
3. Open a web browser and try to access the Internet.
If steps 1–3 do not resolve the problem:
4. Reset your modem.
To reset your DSL modem router, use a pin or paper clip to press
in and hold the Reset button.
NETGEAR genie App
The genie app is your home network dashboard. It lets you easily
view, manage, and control your entire home network, and helps you
fix common network problems. You can use the genie app or the
genie mobile app.
WiFi Connection
Router Settings
STATUS Connected
Click here
Network Map
Parental Controls
Number of devices 16
Click here
Click here
genie app
Visit the NETGEAR genie web page at
From the genie app, you can do the following:
Internet. Monitor and repair Internet connectivity issues, for both
wired and wireless connections.
WiFi Connection. View or change your router wireless settings.
Router Settings. Log in to your router to view or change its
Network Map. View network devices connected to your network.
Parental Controls. Manage Parental Controls to protect devices
in your network from inappropriate contents.
ReadySHARE. If you connected a USB storage device or printer
to the USB port on the router, then you can access its contents.
Support. Support FAQs are available on your computer without
an Internet connection. You can get answers to common router
issues here. Some simple network tools are available to help you
debug the network as well.
NETGEAR genie Mobile App
To install the genie mobile app:
1. Using your mobile device, navigate to the Apple AppStore or
Google Play for Android, and search for NETGEAR genie. You
can use the following QR codes to speed up this process:
iPad App
iPhone App
Android App
2. Install the app on your iPad or phone.
3. Launch the app, and it displays the dashboard screen.
To use this app, you need a
Wi-Fi connection from your
phone or iPad to your NETGEAR
home network.
• Manage Wi-Fi settings and guest
access for your home network.
• View a map of your network.
• Set up or manage Parental
• Use Traffic Meter to check your
Internet usage.
• With My Media, play media on
devices on your network.
ReadySHARE Access
After installation and setup, you can insert a USB storage device into
the USB port on the modem router and share the contents with other
network users. (If your USB device has special drivers, it is not
Note: If your USB device requires a power supply, you have to use it
when connecting your USB device to a NETGEAR router or gateway.
It might take up to 2 minutes before the USB drive is ready for sharing
after it is connected to the router.
To access your USB device:
On Windows systems, use any of these methods:
Select Start > Run and enter \\readyshare in the dialog box.
Click OK.
Open Explorer or Safari and enter \\readyshare in the address
Open My Network Places, and enter \\readyshare in the address
On Mac systems, do this:
1. Select Go > Connect to Server.
2. Enter smb://readyshare as the server address.
3. Click Connect.
The readyshareconnect.exe file (for Windows) is available to
download here:
ReadySHARE Cloud
ReadySHARE Cloud allows you to access and share files on an
attached USB hard drive anywhere you have an Internet connection.
To set up your account, go here:
ReadySHARE Print
The USB Control Center utility allows you to control a shared USB
device from your computer that is connected to the USB port on your
router. The utility allows you to control a printer.
The utility has to be installed on each computer on your network from
which you want to control the device. You can download this utility at
When you launch the USB Control Center utility, a screen similar to
the following displays:
This is the main screen, which shows a device icon, the description
for this USB device, and its status.
Available. The device is available from the computer that you are
Waiting to Connect. You need to connect to this device from the
computer that you are using. If this is the first time you are
connecting, you might be prompted to install the device driver.
The following menu selections are available:
System. Exit the utility.
Tools. Access the Control Center Configuration screen to set up
your shared USB device. See the following section, Control
Center Configuration.
About. View details about the USB Control Center software.
Control Center Configuration
Select Tools > Configuration to display the following screen:
Automatically execute when logging on Windows. Select this
check box to have the utility start automatically when you are logged
in to Windows.
Timeout. Specify the time-out value for holding the USB resource
when it is not in use.
Language. Select the display language for this utility.
USB Printer
The first time that you use a printer, you need to click Connect. You
might be asked to install the driver for this printer. After the driver is
installed, the printer status changes to Available.
Note: Some USB printers (for example: HP and Lexmark printer)
request that you do not connect the USB cable until you are prompted
by the installation software.
If the USB printer is detected and connected automatically, you need
to disconnect the printer, and then wait for the prompt asking you to
click Connect.
Once the printer shows Available status, the grayed-out Paused state
no longer displays in the Windows Printers and Faxes window.
This USB printer is ready. The utility does not always need to hold the
connection of this USB printer. Once there is any print job for this
printer, the USB utility connects to this USB printer automatically, then
prints. After the print job is done, the printer status returns to the
Paused state.
Scan with a Multifunction Printer
You can use the scan feature of a multifunction printer.
1. Make sure that the printer’s status shows as Available.
2. Click the Network Scanner button.
This activates the scanner window that is used to perform the
Time Machine
Time Machine works on Mac computers only, and automatically
backs up everything on your computer to a USB hard drive connected
to it. Here is how it works:
Note: If you are already using Time Machine software with your USB
hard drive, you can skip Steps 1 through 3 and go to Step 4.
1. Physically connect the USB hard drive to your Mac.
2. Format your USB hard drive.
3. Open the disk utility and format your drive.
4. You can now use Time Machine wirelessly by connecting the USB
hard drive to your DGND4000 router.
5. From your MAC desktop, open Macintosh HD.
6. Click the Connect As button. In the pop-up window, select
Registered User, and enter admin as the user name and
password as the password. Click Connect.
7. After connecting successfully, you can list your connected devices.
Note that you see one extra device, called admin, whenever you
log in as admin.
8. Click the Use for Backup button to complete your selection.
9. Enter the password (password), and the backup begins.
Other Features
For additional features, including Live Parental Controls, Traffic
Metering, ReadySHARE, Guest Access, and more, please log in to
your router at
© 2012 NETGEAR, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form or by
any means without the written permission of NETGEAR, Inc.
DO NOT stack equipment, or place equipment in tight spaces or in drawers.
Be sure that your equipment is surrounded by at least 2 inches (5 cm) of air
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks
and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the
United States and/or other countries. Information is subject to change without
notice. Other brand and product names are registered trademarks or
trademarks of their respective holders. © 2012 NETGEAR, Inc. All rights
Statement of Conditions
In the interest of improving internal design, operational function, and/or
reliability, NETGEAR reserves the right to make changes to the products
described in this document without notice. NETGEAR does not assume any
liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF