View 2017 Toyota Tacoma Security System

View 2017 Toyota Tacoma Security System
TOYOTA
PREPARATION
TACOMA
2016–
Part Number: PT398-35160
Kit Contents
Item #
Quantity
1
2
2016 MY Tacoma with Automatic Transmission.
Description
1
V5 Wire Harness
GBS ECU Mounting Bracket
1
Conflicts
Do not install into Vehicles without Hood Switch Connector, with Factory Alarm or Manual Transmission (Refer to Page 6).
Item#
Quantity
1
2
3
1
1
10
GBS ECU
Foam Tape
Wire Ties
4
5
6
7
1
1
1
2
8
2
M6 Nut
Jumper Connector
GBS Microphone
V5 Window Label English
00107-VIPWS
V5 Window Label Spanish PT39848142-AA
9
2
10
2
11
1
V2 Window Label English
(Discard)
V2 Window Label Spanish
(Discard)
V2 Owner’s Guide (Discard)
11
1
V5 Owner’s Guide
Description
Recommended Sequence of Application
Item#
Item#
Nylon Panel Removal Tool
Side Cutters
Torque Wrench
Tape
Socket
Special Chemicals
Cleaner
Issue: A 09/29/15
Description
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk
of injury.
CAUTION: A process that must be carefully
observed in order to reduce the risk of damage
to the accessory/vehicle and to ensure a quality
installation.
TOOLS & EQUIPMENT: Used in Figures calls out
the specific tools and equipment recommended
for this process.
Personal & Vehicle Protection Description
Safety Glasses
Safety Gloves
(Optional)
Vehicle Protection
Blankets
Special Tools
Screwdriver
Quantity
Legend
Recommended Tools
Techstream
Installation Tools
Description
Vehicle Service Parts
Description
Striker Tool
Quantity
*Mandatory
Additional Items Required For Installation
Quantity
RS3200 PLUS
General Applicability
Hardware Bag Contents Additional
Item#
TVIP V5
CAD-E IADS P/N ALL
02-016-01
Use latest version on TIS
#2 Phillips, Flat Blade
Jeweler’s
e.g. Panel Pry Tool #1
Toyota SST# 0000206001-01
Battery: 48 in•lbf (5.4
N•m),
Clear
10mm, extension
VDC Approved Cleaner
Page 1 of 27
REVISION MARK : This mark highlights a
change in installation with respect to previous
issue.
SAFETY TORQUE: This mark indicates that
torque is related to safety.
TOYOTA
PREPARATION
TACOMA
2016–
TVIP V5
RS3200 PLUS
Kit Contents
Service Part #’s
GBS ECU
Bracket
GBS ECU
x1
V5 Harness
x1
M6 Nut
x1
Jumper Connector
x1
x1
Wire Tie
GBS Microphone
x10
V2 Window Label
x1
PT398-35070
08190-0C820
V2 Owner’s Guide
V5 Window Label
V5 Owner’s Guide
Foam Tape
DISCARD
English x2
Spanish x2
x1
English x2
Spanish x2
x1
x1
(E) 00107-VIPWS
(S) PT398-48142-AA
Accessory Installation Practice (read before installation)
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices”
document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
• Safety (eye protection, checking torque procedure, etc.)
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your TOYOTA dealer for a copy of this document.
Issue: A 09/29/15
Page 2 of 27
Wire Harness Outline
M
Description
A
5P White
B
26P White
C
26P White
E
-
8P White
(for GBS ECU)
F
-
10P Grey
G
-
10P Grey
M
-
4P White
(for GBS MIC)
W
-
White Tape
Z
-
GBS ECU
TACOMA
Z
Vehicle
TOYOTA
TVIP
PREPARATION
Issue: A 09/29/15
TOYOTA TACOMA
E
W
Page 3 of 27
A
B
G
2016–
C
F
TVIP V5
RS3200 PLUS
*Color of Harness on Overview corresponds with Colored Tape near Connectors on Harness.
Wire Harness Outline*
Vehicle
Description
A
Jumper Connector
B
Vehicle’s Connector
TOYOTA
TVIP
PREPARATION
TACOMA
Issue: A 09/29/15
TOYOTA TACOMA
2016–
Page 4 of 27
A
B
TVIP V5
RS3200 PLUS
*Color of Harness on Overview corresponds with Colored Tape near Connectors on Harness.
TOYOTA
PREPARATION
TACOMA
2016–
TVIP V5
RS3200 PLUS
TOYOTA TACOMA
xx
Wire Tie Overview*
1
2
3
4
6
7
5
8
9
Issue: A 09/29/15
Page 5 of 27
Wire Tie location and number.
TOYOTA
PROCEDURE
TACOMA
2016–
TVIP V5
RS3200 PLUS
Does Vehicle have Hood Switch Dummy Connector installed?
NO
YES
With
Without
Hood Switch
Dummy Connector
Hood Switch
Dummy Connector
(Continue to Installation)
(DO NOT INSTALL V5)
Fig. 1-1
10mm Socket
1. Hood Switch Jumper
Connector Installation.
NOTE: Protect the Fender before
starting.
a. Place the Vehicle in Park with
the Parking Brake set.
b. Disconnect the Negative Battery
Terminal. (Fig. 1- 1)
• Note the Battery Cable Position
as it will be re-installed in the
same position.
CAUTION: Do not touch the
Positive Terminal. (Fig. 1- 1)
Issue: A 09/29/15
Page 6 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
TVIP V5
RS3200 PLUS
NOTE: Ensure all Kit parts are
thoroughly inspected before
Installation.
Fig. 1-2
c.
Disconnect the Vehicle’s
Connector from the Dummy
Connector. (Fig. 1-2)
• Discard the Dummy Connector.
d. Remove the Dummy Connector from the Vehicle. (Fig. 1-2)
NOTE: Push behind Metal
Bracket. (Fig. 1-2)
e. Install the Jumper Connector
to the Vehicle’s Hood Switch
Connector and attach to
Vehicle. (Fig. 1-3)
Fig. 1-3
Side Cutters
Fig. 1-4
1
Issue: A 09/29/15
Page 7 of 27
f.
Secure the Jumper Connector
Harness loop to the Jumper
Connector using 1 Wire Tie (#1).
(Fig. 1- 4)
NOTE: Make sure to insert Wire
Tie through Jumper Connector
Harness loop as shown. (Fig. 1- 4)
TOYOTA
PROCEDURE
TACOMA
2016–
Disassembly Overview
TVIP V5
RS3200 PLUS
1
DS Step Cover
2
DS Cowl Cover
3
DS Lower Dash Cover
ճ
ղ
ձ
Disconnect all Corresponding
Connectors.
Fig. 2-1
Nylon Panel Removal Tool
2. Vehicle Disassembly.
NOTE: Ensure all disassembled
Vehicle Parts are thoroughly
inspected. (Fig. 2-1)
a. Remove the Driver’s Side
Step Cover. (Fig. 2- 1)
Issue: A 09/29/15
Page 8 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
Nylon Panel Removal Tool
Fig. 2-2
TVIP V5
RS3200 PLUS
b. Remove the Driver’s Side Cowl
Cover as shown. (Fig. 2- 2)
• Remove 1 Nut.
Nylon Panel Removal Tool, 10mm Socket
Fig. 2-3
c.
Dislodge the Lower Dash
Cover. (Fig. 2- 3)
• Remove 3 Bolts.
NOTE: The Bolt on the left is
Silver and different from the other
Bolts. Make sure and install the
Silver Bolt on the left side during
re-installation. (Fig. 2- 3)
Fig. 2-4
d. Remove the Hood Latch
Cable from the Hood Latch
Lever. (Fig. 2- 4)
e. Remove the Lower Dash
Cover.
• Disconnect all Connectors.
Issue: A 09/29/15
Page 9 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
Flatblade Jeweler’s Screwdriver
Fig. 3-1
TVIP V5
RS3200 PLUS
3. GBS ECU Preparation
and Installation.
a. Set the GBS Sensitivity Value
to “6.” (Fig. 3- 1)
b. Attach the GBS ECU Bracket
to the GBS ECU. (Fig. 3- 2)
Fig. 3-2
10mm Socket
Fig. 3-3
Guide Pin Location
c.
Install the GBS ECU to the the
Vehicle’s Reinforcement using
the supplied Nut. (Fig. 3- 3)
NOTE: Make sure the Guide Pin
is seated correctly. (Fig. 3-3)
NOTE: Verify that the Nut is
tightened securely.
Issue: A 09/29/15
Page 10 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 4-1
Fig. 4-2
TVIP V5
RS3200 PLUS
4. V5 Harness Installation.
a. Plug in the V5 8P White
Connector to the GBS ECU.
(Fig. 4- 1)
b. Locate the Vehicle’s 5P
Connector and remove the Tape
securing it. (Fig. 4- 2)
c.
Issue: A 09/29/15
Page 11 of 27
Connect the Vehicle’s 5P Connector to the V5 5P White Connector. (Fig. 4- 2)
TOYOTA
PROCEDURE
TACOMA
2016–
Side Cutters
Fig. 4-3
TVIP V5
RS3200 PLUS
d. Secure the V5 Harness’s White
Tape Marker to the Vehicle
Harness using 1 Wire Tie (#2).
(Fig. 4-3)
e. Cut Foam Tape in Half.
(Fig. 4-3)
f.
Using 1/2 piece of Foam Tape,
wrap the 5P White Connectors.
(Fig. 4-3)
g. Secure the 5P White
Connectors to the Vehicle
Harness using 1 Wire Tie (#3).
(Fig. 4-3)
2
1
3
2
Side Cutters
Fig. 4-4
2
CAUTION: Ensure to only secure
the V5 Harness’s Red Tape Marker
to the Protected Vehicle Harness.
(Fig. 4-4)
3
4
Issue: A 09/29/15
h. Secure the V5 Harness’s Red
Tape Marker to the Vehicle
Harness using 1 Wire Tie (#4).
(Fig. 4-4)
Page 12 of 27
Side Cutters
TOYOTA
PROCEDURE
Fig. 4-5
TACOMA
2016–
TVIP V5
RS3200 PLUS
i.
Side Cutters
Fig. 4-5
FRONT VIEW
4
Secure the V5 Harness to
the Vehicle Harness using
1 Wire Tie (#5). (Fig. 4-5)
NOTE: Do not secure to the
Hood Latch Cable.
j.
Route the V5 Harness toward
the Driver’s Cowl Area. (Fig. 4-5)
k.
Secure the V5 Harness to
the Vehicle Harness using
1 Wire Tie (#6). (Fig. 4-5)
l.
Route the V5 Harness toward
the Rear Side of the Vehicle
Harness and secure the V5
Harness with 1 Wire Tie (#7).
(Fig. 4-5)
6
55
Air Bag
BOTTOM VIEW
4
7
Air Bag
Side Cowl
Connector
Block
Fig. 4-6
7
Side Cowl
Connector
Block
Issue: A 09/29/15
Page 13 of 27
m. Disconnect the Vehicle’s 26P
Connector from the Driver’s
Side Cowl Connector Block.
(Fig. 4-6)
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 4-8
7
Side Cutters
Fig. 4-9
TVIP V5
RS3200 PLUS
n. Connect the V5 26P White
Connectors in between the
Vehicle’s 26P Connector and
Driver’s Side Cowl Connector
Block. (Fig. 4-8)
o. Secure the 26P White
Connectors to Vehicle Harness
using 1 Wire Tie (#8). (Fig. 4-9)
p. Disconnect the Vehicle’s 10P
Connector from the Driver’s Side
Lower Cowl Connector Block.
(Fig. 4-9)
8
Fig. 4-10
7
8
Issue: A 09/29/15
Page 14 of 27
q. Connect the V5 10P Grey
Connectors in between the
Vehicle’s 10P Connectors.
(Fig. 4-10)
TOYOTA
PROCEDURE
TACOMA
2016–
TVIP V5
RS3200 PLUS
r.
Side Cutters
Fig. 4-11
Secure the 10P Grey
Connectors to Vehicle
Harness using 1 Wire Tie
(#9). (Fig. 4-11)
8
9
Fig. 5-1
5. GBS Microphone
Installation.
a. Remove the indicated Knockout
cover. (Fig. 5-1)
b. Install the GBS Microphone into
the Open Knockout until it snaps
in place. (Fig. 5-1)
Fig. 5-2
c.
Reconnect the Connectors on
the Lower Dash Cover. (Fig. 5-2)
d. Connect the V5 Harness 4P
White Connector to the GBS
Microphone. (Fig. 5-2)
Issue: A 09/29/15
Page 15 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
10mm Socket, Torque Wrench
Fig. 6-1
TVIP V5
RS3200 PLUS
6. Registration Preparation.
a. Reassemble the Vehicle.
(Fig. 6-1)
NOTE: Make sure that all
Connectors are reconnected.
(Fig. 6-1)
NOTE: Verify that panels fit
together properly, with no
uneven gaps. (Fig. 6-1)
ձ
ղ
ճ
Fig. 3-9
Issue: A 09/29/15
Page 16 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 7-1
TVIP V5
RS3200 PLUS
7. Registration.
a. Verify that the Short Pin is
Installed. (Fig. 7-1)
•
10mm Socket
Fig. 7-2
If not Install now.
b. Temporarily reconnect the
Negative Battery Cable.
(Fig. 7-2)
CAUTION: Do not touch the
Positive terminal. (Fig. 7-2)
Fig. 7-3
c.
Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port. (Fig. 7-3)
d. Turn the Ignition Switch to “ON”
position. (Fig. 7-3)
Issue: A 09/29/15
Page 17 of 27
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 7-4
TVIP V5
RS3200 PLUS
e. Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop.
f.
Fig. 7-5
TIS techstream
File Function
Setup
TIS
User
Help
Connect to Vehicle
Vehicle Connection Wizard(S301-04)
Select the Information and press Next
Open Scan Data File
t e cRequired
h s Information:
tream
Launch TIS
Division:
XXXXXX
Model:
XXXXXXXXX
Model Year:
20XX
Engine:
XXXXXXXX
New Users Demo
Check for Scantool
Updates
Generic OBD II
Software
Registration
Click “Connect to Vehicle”.
(Fig. 7-4)
g. Confirm that the information
displayed on the Vehicle
Connection Wizard is correct
for the vehicle. If not, verify
that the Techstream is
properly connected. (Fig. 7-5)
h. Click “Next>.” (Fig. 7-5)
Option:
User/Language
Selection
Log Out
Optional Information:
VIN:
xxxxxxxxxxxxxxxxxxx
ABS
Memo:
Manual
Help
<Back
Next>
Cancel
Ver x.xx.xxx
Fig. 7-6
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
System Selection Menu
Health Check
Air Conditioner
Combination Meter
*Sliding Roof
SRS Airbag
Main Body
Tilt&Telescopic
Main Body
Back Door
*Accessory Gateway *Driver Door
Combination Meter Mirror
D Door Motor
Sliding Roof
*Passenger Door
Driver Seat
Occupant Detection
Customize
Setting
ECU
Reprogramming
CAN
Bus. Check
Print
Close
S601-03
Issue: A 09/29/15
Generic English
DLC3
Page 18 of 27
i.
Click “Customize Setting.”
(Fig. 7-6)
j.
Click
(Fig. 7-6).
TOYOTA
TACOMA
PROCEDURE
2016–
Fig. 7-7
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Wiper
Warning
Tilt & Telesco
Air Conditioner
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
Sensor
Unit conversion
Smart / Access
Others
TVSS
Option Setup
TVIP V5
RS3200 PLUS
k.
Make sure that the
“Customize” tab is selected.
(Fig. 7-7)
l.
Select “Option Setup”.
(Fig. 7-7)
m. Click
(Fig. 7-7)
Print
Close
S601-03
Generic English
DLC3
Fig. 7-8
o. Click
TIS techstream - 10645
File Function Setup TIS
System Select
n. Select “ON.” (Fig. 7-8)
(Fig. 7-8)
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Customize (S601-06)
Wiper
Warning
Select Customize Parameter
Tilt & Telesco
ITEM
Air Conditioner
Security System
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
SETTING
Sensor
OFF Unit conversion
ON
Smart / Access
Others
TVSS
Option Setup
Item Description
Print
Close
S601-03
Generic English
DLC3
Fig. 7-9
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Utility Selection Menue
Select desired Utility and then press Next button.
Trouble Codes
Data List
Custimize
ECU Communication
ID (S601-06)
Registration
Customize
Smart Code Registration
Select Customize Parameter
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
ITEM
Security System
OFF
ON
SETTING
Active Test
Monitor
Utility
Customize (S601-07)
Press Next to make the selected customize
changes
Next
Cancel
Item Description
Print
Close
S601-03
Issue: A 09/29/15
Generic English
DLC3
Page 19 of 27
p. Click “Next” to accept the
changes to the Vehicle.
(Fig. 7-9)
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 7-10
TVIP V5
RS3200 PLUS
q. Click
(Fig. 7-10)
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Customize (S601-06)
Wiper
Warning
Select Customize Parameter
Tilt & Telesco
ITEM
Air Conditioner
Security System
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
SETTING
Sensor
OFF Unit conversion
ON
Smart / Access
Others
TVSS
Option Setup
Item Description
Print
Close
S601-03
Generic English
DLC3
Fig. 7-11
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Select Customize Function
Wireless Door Lock
Security
Wiper
Warning
Tilt & Telesco
Air Conditioner
Display
Retractable Hardtop
Compass Colibration
PSD & PBD operation
Seat
Door Lock
Power Window
Illuminated Entry
Light Control
Slide Roof
Sensor
Unit conversion
Smart / Access
Others
TVSS
Option Setup
Print
Close
S601-03
Issue: A 09/29/15
Generic English
DLC3
Page 20 of 27
r.
Click “Close.” (Fig. 7-11)
TOYOTA
PROCEDURE
TACOMA
2016–
Fig. 8-1
Clear Tape
TVIP V5
RS3200 PLUS
8. Complete the Installation.
For US Vehicles use the English Tags
and Labels, and discard the Spanish
Tags and Labels.
10 mm
For Mexico Vehicles use the Spanish
Tags and Labels, and discard the
English Tags and Labels.
a. Use VDC Approved Cleaner
to clean the inside of the Front
Door Windows.
MOLDING
C
ET
E
TH ER
H
N
OT
G
O
I
AL
NT
TO ALIG
W
HO W TO
HO
TO
NG
HI LS
BE
LA
1– 5 mm
b. Use a piece of Clear Tape
to lift the Label off its protective
backing.
CAUTION: Do not touch
the adhesive surface.
MOLDING
c.
Attach the Label as shown.
(Fig. 8-1)
NOTE: Make sure to Align the
Label according to Etching or Other
Label. (Fig. 8-1)
REPEAT: Steps 5a - 5c on the
other window.
Torque Wrench
Fig. 8-2
d. Position the Negative Battery
Cable at the original factory
position. (Fig. 8-2)
Torque: 5.4 N•m (48 in•lbf)
CAUTION: Do not touch the
Positive terminal. (Fig. 8-2)
e. Clean up and Remove trash.
f.
Issue: A 09/29/15
Page 21 of 27
Sealed in its protective bag,
place the Owner’s Manual in the
Glove Box.
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Accessory Function Checks
For Vehicles without Key Fob: Skip to Page 24.
Roll up all windows, and exit the vehicle with the remote.
Perform
Look For
1
Press and release the remote control lock
button to start the system’s arming process.
The turn signal lights flash once.
All doors lock.
The security LED lights up.
2
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
3
Press and release the remote control’s
unlock button to disarm the system.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED stops flashing.
Open the driver’s door, insert the key into the ignition switch and turn it to “ON.” Roll down all the windows,
remove the key and exit the vehicle.
4
Arm and disarm the system with the remote
again, then wait 30 seconds.
The doors automatically relock.
The system automatically starts the arming process.
5
Press and release the remote control’s
unlock button again to stop the arming
process.
Refer to step 3
6
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
8
Reach inside and manually unlock the
driver’s door to trigger an alarm.
The driver’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up. (For some vehicles the LED
will continue to flash)
9
Manually unlock the driver’s door again and
hold it unlocked, open the door, then sit in
the driver’s seat.
The driver’s door lock attempts to lock repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue flashing.
The Security LED remains on. (For some vehicles the
LED will continue to flash)
10
Insert the key into the ignition switch and
turn it to “START” to stop the alarm.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The Security LED turns off.
The starter cranks and the engine starts.
(For Smart Vehicles, press “START” button)
Turn the key back to “LOCK”, remove it, and then exit the vehicle.
11
With the door open, press the lock switch
on the door to lock the doors, then close the
door to start the system’s arming process.
All doors lock.
The Security LED lights up.
12
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
Issue: A 09/29/15
Page 22 of 27
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
13
Reach inside and manually unlock the front
passenger’s door to trigger an alarm.
The front passenger’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up. (For some vehicles the LED
will continue to flash)
14
Press and release the remote control’s
unlock button to stop the alarm.
The horn stops sounding.
All the lights stop flashing.
The Security LED turns off.
15
Press and release the remote control’s lock
button to start the system’s arming process,
then wait 30 seconds until the system is
armed.
Refer to steps 1 and 2.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available)
Refer to step 13.
17
Press and release the remote control’s
unlock button to stop the alarm.
Refer to Step 14.
18
Repeat the above steps with the other rear
passenger door. (if available)
Refer to steps 1, 2, and 13.
Roll up all windows, remove the key and exit the vehicle.
For Smart Vehicles: Take out the Smart Key and the Smart Card Key from the Vehicle. Place them 15 ft. (4.5 meters)
or more away from the Vehicle.
19
Press and release the remote control’s lock
button to start the arming process.
Refer to step 1.
20
Wait 30 seconds.
After 30 seconds, the Security LED starts flashing; the
system is now armed.
Perform the following check in a temperature-controlled environment. (50°- 90° F)
21
With the tip of a key, or Striker Tool pulled
all the way out (PPO only), tap the center
of the driver’s door window to trigger the
alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up. (For some vehicles the LED
will continue to flash)
22
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to Step 14.
For Smart Vehicles: If the alarm does not trigger during functional verifications the Smart Key and Smart Card Key
might be too close. Move them farther from the vehicle and test the system again.
NOTE: If the alarm does not trigger during the Glass Breakage Test, increase the GBS sensitivity to the next setting
and test again.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Skip to Vehicle Function Checks: Skip to Page 26.
Issue: A 09/29/15
Page 23 of 27
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Accessory Function Checks (Vehicles Without Key Fob)
Roll up all windows, and exit the vehicle.
Perform
Look For
1
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
All doors lock.
The Security LED lights up.
2
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
3
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the arming process.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED stops flashing.
Open the driver’s door, insert the key into the ignition switch and turn it to “ON.” Roll down all the windows
and exit the vehicle.
4
Arm and disarm the system with the key,
then wait 30 seconds.
The doors automatically relock.
The system automatically starts the arming process.
5
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the arming process.
Refer to step 3
6
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
8
Reach inside and manually unlock the
driver’s door to trigger an alarm.
The driver’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up. (For some vehicles the LED
will continue to flash)
9
Manually unlock the driver’s door again and
keep it unlocked, open the door, then sit in
the driver’s seat.
The driver’s door lock attempts to lock repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue flashing.
The Security LED remains on. (For some vehicles the
LED will continue to flash)
10
Insert the key into the ignition switch and
turn it to “START” to stop the alarm.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The Security LED turns off.
The starter cranks and the engine starts.
Turn the key back to “LOCK”, remove it, and then exit the vehicle.
11
With the door open, press the lock switch
on the door to lock the doors, then close the
door to start the system’s arming process.
All doors lock.
The Security LED lights up.
12
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
Issue: A 09/29/15
Page 24 of 27
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available)
Refer to step 13.
17
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to Step 14.
18
Repeat the above steps with the other rear
passenger door. (if available)
Refer to steps 1, 2, and 13.
TVIP V5
RS3200 PLUS
Roll up all windows, exit the vehicle.
19
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
Refer to step 1.
20
Wait 30 seconds.
After 30 seconds, the Security LED starts flashing; the
system is now armed.
Perform the following check in a temperature-controlled environment. (50°- 90° F)
21
With the tip of a key, or Striker Tool pulled
all the way out (PPO only), tap the center
of the driver’s door window to trigger the
alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up. (For some vehicles the LED
will continue to flash)
22
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to Step 14.
NOTE: If the alarm does not trigger during the Glass Breakage Test, increase the GBS sensitivity to the next setting
and test again.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Issue: A 09/29/15
Page 25 of 27
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Vehicle Function Checks
Function
Enter the Vehicle
□
□
Dome/Courtesy Lights
Horn
Start the Vehicle
□
□
Starter
Panel/Switch Illumination
Function
□
□
□
Steering Wheel Column Adjusts
Without Interference
Hood Latch
Gauges
□
ABS Light (if equipped)
□
Track/Skid Control Light (if equipped)
□
Tire Pressure Monitoring System
(TPMS)
If the warning light remains on, it may
indicate a system malfunction.
□
Lamp Failure Sensor
□
Seat Belt Warning Light
□
Air Bag Warning Light
Prior to TPMS activation and Pre-delivery
Service (PDS) of the Vehicle the TPMS light
will blink when IG is turned on.
Cruise Control Light (if equipped)
After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few
seconds and go off when IG is turned on.
□
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
Using a Mirror or Assistant check the following.
□
□
□
□
Trunk/Tailgate/Bed Lights (if equipped)
Brake Lights
Backup Lights
□
□
□
If the warning light remains on, it may
indicate a system malfunction.
Tail Lights
Daytime Running Lights (if equipped)
Marker Lights
Clearance Sonar (if equipped)
Stop the Engine, Place the Vehicle’s IG in the ON position.
□
□
□
□
□
Hazard Lights
Head Lights
High Beams
Power Side Mirrors (if equipped)
Power Sliding Door (if equipped)
Issue: A 09/29/15
□
□
□
□
□
Page 26 of 27
Turn Signal Lights
Fog Lights (if equipped)
Accessory Controls/Illumination (if equipped)
Convenience Memory Settings (if equipped)
Rear Sunshade (if equipped)
TOYOTA
TACOMA
2016–
CHECKLIST – these points MUST be checked to ensure a quality installation.
□
□
□
□
□
□
□
□
□
□
□
Function
Front Wiper/Washer
Power Sun/Moon Roof (if equipped)
Clock (if equipped)
Audio/Video (if equipped)
Steering Wheel Audio Control (if equipped)
Front Windshield Defogger (if equipped)
Side Mirror Defogger (if equipped)
Massage Seats (if equipped)
Glove Box Light (if equipped)
Power Locks (if equipped)
Power Seats (if equipped)
□
□
□
□
□
□
□
□
□
□
□
TVIP V5
RS3200 PLUS
Function
Rear Wiper/Washer (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Navigation System (if equipped)
USB Connections (if equipped)
HVAC
Rear Window Defogger (if equipped)
Accessory Power Socket (if equipped)
Heated/Vented Seats (if equipped)
Passenger Air Bag Switch (if equipped)
Power Windows (if equipped)
Key Sensor Buzzer
Vehicle Appearance Check
Perform
□
After accessory installation and removal
of protective cover(s), perform a visual
inspection of the vehicle.
Look For
Ensure no damage (including scuffs and scratches) was
caused during the installation process.
(For PPO installations, refer to TMS Accessory Quality
Shipping Standard.)
Remove the short pin after Function check.
Check with your Port/Dealer to see if this step is necessary.
Issue: A 09/29/15
Page 27 of 27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement