BodyCraft F431 Lat Low Pull Attachment Assembly

BodyCraft F431 Lat Low Pull Attachment Assembly
 LAT & LOW PULL ATTACHMENT FOR POWER RACK
STRENGTH TRAINING SYSTEM
INSTRUCTION MANUAL
MODEL : F431
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions,
or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized
dealer service centers or our home office customer service department. Please call your local dealer
for assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide
immediate assistance to you, free of charge.
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system
is guaranteed for as long as you own it. We will repair or replace anything that goes wrong.
Bodycraft 1s a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
BEFORE YOU BEGIN
Congratulations and thank you gor selecting the BODYCRAFT LAT & LOW
PULL ATTACHMENT FOR POWER RACK strength training system.The
- BODYCRAFT LAT & LOW PULL ATTACHMENT FOR POWER RACK
offers an impressive array of strength training exercises to develop every major
muscle group of the body. Whether your goal is cardiovascular fitness, a
shapely, toned body or dramatic muscle size and strength, the BODYCRAFT
LAT & LOW PULL ATTACHMENT FOR POWER RACK will help you
achieve the specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT LAT & LOW PULL ATTACHMENT FOR
POWER RACK. Keep this manual for future reference.
If you have additional questions, please call your local BODYCRAFT dealer or
our customer service department at 800-990-5556 Monday through Friday,
9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1. This product must be assembled on a flat, level surface to assure its
proper function. |
2. Clean pads and frame on a regular basis. We recommend warm, soapy
~ water. Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn parts
immediately. Failure to do so may result in serious injury.
4. Keep children away from the BODYCRAFT LAT & LOW PULL
ATTACHMENT FOR POWER RACK at all times.
5. Keep your hands away from moving parts other than the designated
handles.
6. When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
Exercise with care to avoid injury.
If unsure about the proper use of the BODYCRAFT LAT & LOW PULL
ATTACHMENT FOR POWER RACK strength training system call your
local BODYCRAFT dealer or our customer service department at
800-990-5556.
ex
|
EXPLODED VIEW
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
| 66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
| 81
82
83
NO. DESCRIPTION
BASE FRAME
TOP FRAME
GUIDE ROD 81.8"
75mm X 170mm LINK PLATE
50mm X 170mm LINK PLATE
DOUBLE PULLEY BLOCK
LAT BAR HOLDER
TWO WAY TOP PLATE
LAT BAR
LOW ROW BAR
STACK SPACER 24"
45mm X 75mm CAP
45mm X 75mm PLUG
PULLEY
RUBBER DONUT
BUSHING 1"
GRIP OF LAT BAR HOLDER
1" X 200mm HAND GRIP
1" X 140mm HAND GRIP
LOW ROW CHAIN (13 LINK)
SNAP HOOK
TOP CABLE LOCKER
1" SPRING CLIP
CABLE
1/2" X 4" HEX HEAD BOLT
1/2" X 2" HEX HEAD BOLT
3/8" X 1-3/4" HEX HEAD BOLT
5/16" X 1/2" HEX HEAD BOLT
7/16" X 3" TOP PLATE BOLT
1/2" WASHER
5/16" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
2"
1/2
3”
ГО № — XONNNN ANDO N dA A A —х = ANAL
>| № В — № —1 Ю №
1/2
PARTS CHART
QTY.
72
75
80
Lo bbc bed
0 1/4 1/2 3/4 1" 1/2
(inch)
4"
I tu |
1/2 5" 4/2 6"
ASSEMBLY
Do NOT tighten any bolt until instructed.
1. Attach Base Frame (51) to Rear Frame of Power rack, using two 1/2" X 4" Hex Bolts (75), one Link
Plate (55) and two 1/2" Nylon Nuts (82). Attach three 45 mm X 75 mm Cap (62) to Base Frame (51).
2. Insert two Guide Rod (53) into holes in Base Frame (51) and slide two Stack Spacer (61) and two
Rubber Donuts (65) over the top of Guide Rod (53).
3. Slide Two Way Top Plate over top of Guide Rod (53). Attach two Rubber Donuts (65) and two Spring
clips to Two Way Top Plate(58).
4. Attach Top Frame (52) over Guide Rod (53) and to Rear Top Frame of Power Rack , using two 1/2" X
3" Hex Bolts (76), Link plate (54 ) , four Washers (80) and two 1/2" Nylon Nut (82) . Attach four
45 mm X 75mm plugs to Top Frame (52).
5. Attach Lat Bar Holder (57) to Top Frame ( 52) ,using two 5/16" X 1/2" bolts (78) and two Washers
(81).
Tighten all Bolts and Nuts.
CABLE INSTALLATION
Top Cable
Assemble cables and pulleys simultaneously.
Insert screw end of Top Cable (74) into slot in front of Top Frame (52) and out of slot in rear of Top Frame.
Attach Pulleys in bracket at these slots with cable running above as shown in Fig. 1 and Fig 2. Route cable
down and around top pulley in Double Pulley Block (56) as shown in Fig.3 . Continue over pulley in
bracket in Top Frame (52)(Fig 4) and down to Two Way Top Plate(58). Tighten cable by screwing threaded
head into pre-installed Top Cable Locker (72) in Two Way Top Plate.
Low Cable
Attach Low Cable under two pulleys on Base frame as shown Fig 6 and Fig 2 . Ball end of cable should be
towards front of machine. Route Low Cable up and over bottom pulley in Double Pulley Block (56) (Fig 3),
and down to threaded frame extension in Base Frame(Fig. 7). Tighten by screwing threaded end into welded
bolt on Base Frame (51).
FIG 3 FIGS
EE ee
Assembly is complete! Please take the following steps before using the gym:
1. Make certain all bolts are tightened securely.
2. Make certain all cables are seated into all pulley grooves. A cable rubbing
against steel will peel the nylon coating, voiding warranty and resulting in a
need for replacement.
3. Pre-stretch the cables. Put the Weight Selector Pin (103) in the bottom hole on
the weight stack. Pull on the cables with great force, helping remove any
kinks and providing any initial cable stretch.
4. Be aware the cables can loosen and slightly stretch upon initial use.
5. The cables should be adjusted as tight as possible, but no so tight as to lift
the Two Way Top Plate (58) above the weight stack. Be certain to secure the
jam nuts after adjustments are made.
6. For better performance, apply a household lubricant (such as silicone) to any
adjustable areas and to the Guide Rods (53).
7. Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the Bodycraft Lat & Low Pull attachment for
Power Rock Home Gym. If You have any questions, please call your
local BodyCraft dealer or call our customer service department at
800-990-5556
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement