CamOne CarCamOne HD 72 Manual Manual
ACME CarCamOne HD 72 is a high-definition camera designed for use in vehicles. It features a 1-inch display, 180-degree rotatable head, and a variety of recording modes.
The CarCamOne HD 72 can record video in 720p resolution at 30 frames per second. It can also take still photos with a resolution of 12 megapixels. The camera has a built-in microphone for recording audio, and it can also be connected to an external microphone for improved sound quality.
The CarCamOne HD 72 has a number of features that make it ideal for use in vehicles. It has a built-in G-sensor that can automatically detect sudden changes in motion, such as a collision. The camera will then automatically start recording and save the footage to the microSD card.
Advertisement
Advertisement
Manual
(
Manual Download as PDF www.camonetec.com
)
CamOne, FlyCamOne, CarCamOne and the CarCamOne Logo are registered Trademarks of ACME the game company, Germany
© copyright 2013 by ACME the game company GmbH
Version: 2.0
Content of the box
Please make sure that the set is complete before starting
CarCamOne High Defi nition 720p Camera
CarCamOne Cable Suction cup Eyelet string
USB-Cable 10Pin – RCA AV-Cable Manual
Table of contents
Content of the box
Preparation
Battery charging
Exchange the battery
Funktional diagramm
Compatible memory cards
How to insert SD card
The panel
Start the camera
Permanent recording inside a car
Splash water protection for usage on motorcycle
On-screen icons
Mode selection
Video recording
Photo shooting
Using the zoom
Playback of video and photos
Setup
Playback at the computer (MS Windows)
Using the camera as a webcam
Different type of mount
Connecting the optional screen
Exchange the lens
Tighten / Untighten the head
Firmware update
Technical data
Troubleshooting
CarCamOne HD Accessoires
Safety advice
Service & Support
15
16
14
14
18
19
13
13
12
13
11
11
9
10
9
9
8
9
6
6
5
6
4
4
2
4
6
7
7
8
Preparation
Compensation for recorded content
ACME will not be responsible in any case for any consequential or direct problems that will lead to a loss of recorded or edited data. Furthermore ACME will not guarantee the content in case the recording or saving is not working properly. The above limitations are as well valid in case the unit has been repaired.
Do not remove the micro SD Card while recording or saving. Do not switch off or take out the battery before the recording has been stopped or as long there is access to the memory, indicated by a rotating circle.
Protect the unit from extreme temperatures. Stop recording at temperatures less than 0°C and higher than 60°C. Remove the camera from the windshield/suction cup in case extreme temperatures might be possible!
It is known that forged accumulators which remarkably look like the original product are offered for the sale again and again.
Some of these rechargeable batteries are not equipped with a proper protection circuit which would satisfy the regulations of the prevailing safety regulations. These accumulators can perhaps lead to fi res or explosions. We assume no liability for accidents, damages or failures which result from the use of a forged accumulator.
Battery charging
The integrated battery is not fully charged when being purchased.
Please charge the battery before you are going to use the camera the fi rst time!
Connect the camera to your computer using the included USB cable to charge. The charging process is indicated by the LED and is fi nished after about 2 hours.
Use the original USB-Cable or the optional available power adaptor only to charge the camera.
Using the adaptor the camera is charged within one hour.
charging indicator
Exchange the battery
Akkufach Deckel
Battery lock
Battery cover
Slide the lock to the top position and remove the cover. The battery is wire connected and can be removed by careful pulling. Insert the new battery the same way - take care of the polarization. Only use original battery to prevent damage of the unit.
(Art-No.: FCHD17).
4
Functional diagramm
180° pivot able head
1”/25,4mm display
Zoom
Release/OK button
Control
Menu (M) button
Port-cover
On/Off switch
Power/Charging LED
Eyelet
10-Pin ComPort
Mini USB 2.0
Micro-SD-Card slot
Reset button
Fixing slots
Battery case
180° pivot able head
Lens
The 10-Pin comport has following setup:
- AV-Out
- 5V IN
- Signal IN for external start/stop (CarcamOne / Motion detection)
Due to limitations in the technology of the display production, single or few dark or light dots might appear. This is not a defect and will not have any impact to the recorded video or photo!
5
Compatible memory cards
Only use Micro-SDHC-Cards rank „Class4“ or higher.
The camera can be used with cards up to 32GB.
The recommended cards are „FCO Rapid Rush” cards at a minimum size of 8GB.
How to insert SD card
Remove the comport cover protecting the sockets and the card slot.
Slide in the card upside down - printed side to the bottom - until it clicks in.
To remove press onto the visible edge of the card, so it will get out by the spring mechanism.
The panel
Zoom in
Zoom out
Up
Start / Stop / OK
Left / 3 seconds for full screen
Right / 3 seconds to fl ip the picture 180°
Menu / 3 seconds for setup down
The buttons placed at the right side of the camera will guide you through the functions of the camera - „Left” and „Right” as well as the button „M” do have a double key mapping.
Press those for 3 seconds to get the second command.
Start the camera
On/Off
Press the button at the left side of the cam to start the camera. CarCamOne will be displayed at the beginning.
For usage inside the car you do not need to press any buttons!
The adaptor in the cigarette socket detects the turning of the engine and starts the camera automatically.
6
Permanent recording inside a car
First clean the window carefully from inside to avoid dirt and crudity on the windshield. Now pull off the protective fi lm from the suction cup and moisten the slightly rubberized surface. Press the suction cup on the windshield and pull the lever down. Make sure that there are not too large temperature differences between the external environment, the internal temperature of the car and the wheel, since the suction cup cannot be mounted otherwise.
Now insert the micro SD card. Push together the fi xation brackets of the suction cup and put on the camera following the notches.
Adjust the camera by moving the suction cup arm. Then plug in the car cable.
By starting the engine, the camera launches automatically and the integrated LED fl ashes green.
After stopping the engine, rotating bars appear and the recording will be fi nished.
The CarCamOne records in 15 Minutes blocks. If the remaining memory for the next recording is not suffi cient, the fi rst recording will be deleted automatically. This causes a minimal gap of 3 seconds between the videos.
Make sure that the camera does not reduce your reactivity in dangerous situations!
Don’t let the device distract you! Don’t use the camera while driving!
The automatic recording starts at a running engine only.
An operation through a power supply or the ignition position is not possible.
If your car has a power saving function (automatic Start- Stop), it is necessary to close the jumper (bridge) inside the car adaptor.
Twist off the plugs lock nut, remove the metal ring and pull off the sticker. The half casings can be opened now.
Set the Jumper
To close the jumper, open the adaptor fi rst. On the PCB you will fi nd the jumper covering one pin only - the default setting to detect the generator.
Remove the Jumper and easily put it on both pins to activate the start of the camera by „ignition” once served with power.
Splash water protection - motorbike
Protect your camera steadily from rain and splash water with the available DiveBox
(Art.No: FCHD31).
The box uses the same fi xture as the cam and is made of high- quality acryl. It´s possible to adjust the cameras head before inserting. For usage in combination with the
CarcamOne-cable the marked area has to be reamed.
Attention: the box is not fully waterproof then anymore!
7
Usage as a regular camera
A
A
Flip 180°
Changing the direction of the head requires to fl ip the picture by 180°. Press the „right” button for 3 seconds to adjust the direction according to your requirements.
Can’t be changed once the recording has been started.
A
A
Full screen
The camera is not displaying the full frame as recorded. This setting allows focusing to the center.
To get the full screen press „left” for 3 seconds.
On-screen icons
Battery status [1]
Timestamp [2]
Exposure [3]
Recording [4]
Mode [5]
Remaining capacity as bargraph [6]
[1] At the top on the right, the tripartite battery status is indicated. If this status is marked red, the internal battery needs to be charged! [2] The box besides it shows the activated timestamp.
[3] Next to the „A” for automatic exposure the chosen preset is displayed here. [4] The red spot indicates the recording. [5] Leftmost you can check the selected mode. The camera symbol for photo mode (followed by a „S“ for serial pictures) – the video camera for video mode (followed by an „E“ for external mode). [6] Below the capacity is indicated in form of a bargraph. Red is the used memory, green shows the remaining capacity.
Mode selection
The camera starts in external mode that can be used directly for recording.
Use the cross pad’s „up“and „down“buttons to change the mode.
Mode
External
Video
Photo
Play
Select the mode with the cross pads up and down, confi rming by pressing “Start”. For details in the selected mode go further on pressing the “M“ button.
8
Following menus appear:
Video
Standard
15 Min
30 Min
45 Min
60 Min
Photo
Single shot
3 Sec
5 Sec
10 Sec
30 Sec
60 Sec
Video recording
Serial pictures in photo mode
Select the running time of the recording. Confi rm selected mode with „Start”. Leave the submenu by pressing the “M” button.
Time Lapse will record with only one frame per second – specially used for nature recordings. Recommended is the use of external energy source. (Power Adaptor Art.-No.: FC3016) – This mode will come with next update.
Videolength in video mode
Activate the serial photo function in the photo mode – select a picture every second up to every 60 seconds. Confi rm the selected interval with the „Start” button or leave the menu pressing the „M” button.
Release button
„START”
When switching on the camera you can start recording immediately pressing the „Start” button. To stop press the button again.
Never remove the SD card or battery when the cam is recording or still operating displayed by a rotating circle!
Photo shooting
Use the cross pad to get to the photo mode. Press the release button once to make a single shot. To activate the serial photo function, press „M” to select the sequence.
Confi rm you selection by pressing the “Start” button again. With next press of “Start” the cam starts the serial photo mode, taking photos for instance every 5 seconds.
Using the zoom
Zoom in
Zoom out
You can use the digital zoom while recording pressing the top buttons of the panel.
The zoom is displayed in a bar in the screen.
Playback of video and photos
Move to „Play” mode to view the recorded data. Recommended is to use a TV or the optional 2,5”
Screen. (Art.-No: FCHD02)
Use the cross pad to move through the recorded fi les and start playing by pressing the release button. Left and right increase or reduce the playback speed.
Playback at the TV
Connect the included RCA-cable to you TV and set it to „AV”
9
System
Language
Date
Time
Timestamp
Externer Modus
Video size
Zoom
FPS
White balance
ISO
Exposure
Effects
Contrast
Sharpness
Resolution
Flip Picture
Auto power off
Auto screen off
Microphone
Light frequency
Formatting
Reset
Update
Setup
Press the „M“-button for 3 seconds to enter the setup.
The setup shows up the installed fi rmware version.
By using the keypanel, you can switch through the menu and choose the modes by pressing the
Record/OK- button.
Change between FlyCamOne HD or CarCamOne HD surface.
(without effect on the options)
Select the language English, German, French or Spanish
Set date: YYYY-MM-DD (year-month-day)
Set time: HH:MM (hour:minute)
Activate the timestamp
Date and Time embedded in the video/ photo
Adjust the preset for video- or photo recordings in the external mode
Select the recording format: HD ready - 1280 x 720p | D1 - 720 x 480p
Preset of the zoom function in 10 steps at camera launch
Select the frames per second - 30FPS (frames per second) are standard. For timelapse recordings, for example a sunset, the recording speed can be reduced down to 1 frame per minute – the video will be played back with 30FPS – that means that 1 hours gets reduced to 2 seconds – use an external power source for timelapse recordings!
For example: USB- Power adaptor
Select light temperature and environment
Change ISO setting 100,200,400,800
Brighter Picture to be adjusted here
Choose off, art, sepia, negative, monochrome, vivid
Select soft, standard or hard contrast
Select soft, standard or hard sharpness
Select high, medium or low resolution
Select 180° fl ip and mirror function here
Select the auto off function: 1, 5 or 15 minutes are available
Battery saving to be selected here - By pressing any button, the screen will be re- activated!
On/Off
For indoor recording select 50Hz or 60Hz
Formatting the card
Return to default settings
Update the Firmware: www.CamOneTec.com
Please note that some menu items may not appear before a fi rmware-/software update.
Check „SoftwareUpdate (Firmware Update)“.
10
System
Language
Date
Time
Timestamp
Externer Modus
Video size
Zoom
FPS
White balance
ISO
Exposure
Effects
Contrast
Sharpness
Resolution
Flip Picture
Auto power off
Auto screen off
Microphone
Light frequency
Formatting
Reset
Update
Change between FlyCamOne HD or CarCamOne HD surface.
(without effect on the options)
Select the language English, German, French or Spanish
Set date: YYYY-MM-DD (year-month-day)
Set time: HH:MM (hour:minute)
Activate the timestamp
Date and Time embedded in the video/ photo
Adjust the preset for video- or photo recordings in the external mode
Select the recording format: HD ready - 1280 x 720p | D1 - 720 x 480p
Preset of the zoom function in 10 steps at camera launch
Select the frames per second - 30FPS (frames per second) are standard. For timelapse recordings, for example a sunset, the recording speed can be reduced down to 1 frame per minute – the video will be played back with 30FPS – that means that 1 hours gets reduced to 2 seconds – use an external power source for timelapse recordings!
For example: USB- Power adaptor
Select light temperature and environment
Change ISO setting 100,200,400,800
Brighter Picture to be adjusted here
Choose off, art, sepia, negative, monochrome, vivid
Select soft, standard or hard contrast
Select soft, standard or hard sharpness
Select high, medium or low resolution
Select 180° fl ip and mirror function here
Select the auto off function: 1, 5 or 15 minutes are available
Battery saving to be selected here - By pressing any button, the screen will be re- activated!
On/Off
For indoor recording select 50Hz or 60Hz
Formatting the card
Return to default settings
Update the Firmware: www.CamOneTec.com
Playback at the computer (MS Windows)
The videos can be displayed at the PC in an easy way.
We recommend to use the VLC Player (freeware) www.vlc-player.org
Connect the camera using the USB cable to your
PC. Select the appearing „MSC” Mass storage
Container to use the camera as a drive.
Press [START] with the left mouse button and select the “Explorer” to display all drives.
Select the exchangeable drive and fi nd the video data in the contained folders.
!
Supports only Windows 32 bit systems.
Using the camera as a webcam
Install the webcam drivers from the homepage (www.CamOneTec.com) and connect the camera to your computer. Select „WebCam” in the menu of the camera. Now you can use the camera - note that you need a microphone for audio transmission.
As an accessory, we offer the FlyCamOne HD Docking
Station (Art.-No.: FCHD13), which loads the camera and transfers data to the computer. The docking station is equipped with a 10pin port and a mini USB port.
For use with the optional infrared motion detector
(Art.-No.: FCHD07) the station is also well suited – just plug the cam into the 10pin port on the station.
The camera starts recording as soon as people or animals are moving in front of the lens (up to 8m).
11
Different type of mount
The line-Up of the FlyCamOne HD contains different type of fi xing systems
Tripod adaptor
The tripod adaptor fi xes the camera to every standard tripod. (Art.-Nr.: FCHD25)
Pendulum mount
The pendulum mount can be screwed or glued to a RC model - it enables the pan movement by a servo. The pendulum function can be locked - but is mandatory when fi xed to a sport kite (Kite Surfi ng). This time the mount is fi xed by straps.
(Art.-Nr.: FCHD26)
Handle bar mount
The mount for the handle bar of a bike fi xes the camera within seconds (Diameter 22-25mm).
(Art.-Nr.: FCHD64)
Suction cup sport
The sucking pad for the windshield or any other smooth surface.
(Art.-Nr.: FCHD39)
Belt mount
Fix the camera to your belt or jacket using the belt clip furthermore with some tape almost anywhere.
(Art.-Nr.: FCHD29)
Universal mount
The mount for the wrist is fi xing the screen, but can be adjusted to the cam as well to use it as a universal fi xing, also for a helmet.
(Art.-Nr.: FCHD30)
Exchangeable lenses
Fast replaceable lenses for the right fi eld of view. Attention:
The 96° and 133° lenses are not suitable for the DiveBox use!
(Art.-Nr.: FCHD49 - 96°, FCHD09 - 133°, FCHD10 - 170°)
Docking station
For battery charging, data transfer on the PC or mounting the camera on the dashboard of your car.
(Art.-Nr.: FCHD13)
12
Connecting the optional screen
The optional 2,5” screen will be plugged into the cam directly. Different mounts allow fi xing it individually. At the wrist when the camera is mounted at the helmet, inside the car, at the handle bar of a bike.
(Art.-Nr.: FCHD02)
The Y-cable enables the simultaneous use of the
CarCamOne-cable and screen!
Exchange the lens
Please Note!
The opened camera head and connectors can be damaged easily. Handle the change carefully and take your time!
To replace the sensor unit, turn the camera head until you can see the screws. Remove the four screws with a Phillips screwdriver.
Carefully remove the plug at the rear of the board. Make sure that the opening of the new board looks in the direction of the broadband cable. Now insert the new sensor unit with the lens on the built-in camera connector.
Fix the new lens carefully with the new, enclosed screws!
Tighten / Untighten the head
Please perform carefully!
Over-tightening of the screw will damage the camera.
If the head moves to easy, or if is too fi x, it can be adjusted by a screw behind the left side frame that can be removed as described above. Turn the screw with a Phillips to left to untighten, turn it to the right to tighten it.
Take care - do not over twist!
Left = light camera head movement
Right = heavy camera head movement
13
Firmware update
To make the best out of your camera, make sure your fi rmware is up to date, which is displayed by pressing the M button for several seconds.
Compare your fi rmware version with the currently listed version on our website.
Website: www.CamOneTec.com
When needed, the most recent fi rmware version can be downloaded here.
To update the camera software (fi rmware update), copy the needed fi le from our website in the root of your memory card.
Go to the main camera menu (Setup) and select the step „Update”.
Then confi rm your choice by clicking „Start”.
The update process takes about 1 minute. The status is indicated on the display.
Do not switch off the camera while updating!
Make sure that the battery is fully charged
Technical data
Power:
Consumption:
Size:
Weight:
Battery:
Format:
Sensor:
Lens:
Zoom:
Screen:
Microphone:
AV-Out:
USB:
Operation temperature:
Humidity
Micro SD/SDHC-Card:
5V (USB / 10Pin Port) / 3,7V (LiPo-battery, 600mAh)
320mAh
95 x 52 x 21mm
53g incl. battery
3,7V 600mAh LiPo
MPeg
5MPix CMOS
55° (exchangeable)
4times digital
1“ / 2,54mm OLED yes yes
Hi-Speed USB (2.0)
0°C to 60°C
10% to 80% (non-condensing)
Micro SD <= 32GB – Class 4 or higher
14
Troubleshooting
Please note: the camera will record when the engine runs only.
Key position “Ignition” will start the camera only when the red jumper inside the adaptor has been removed!
Error
Display does not show anything, Green LED is not blinking
Cause
No power at the socket.
Solution
Replace car s fuse
The Video jerks when playing at the PC.
The video is turned 180°
Date and time will not be displayed in a correct way
Display shows „Error“
Fuse in the Adaptor melted
The card, the USB connection or the PC is too slow
Wrong Settings
Wrong Settings
Replace adaptor s fuse
Download the fi le to the PC fi rst. Stop other applications.
Read „ 180° turn“
Change Settings in the Setup
Display shows „Memory“
The camera stops recording at every traffi c light or when stopping the car.
The camera stops during normal drive and starts after 10, 15 minutes again.
The camera cannot get space – too many small fi les.
No more free memory left.
Your car has power saving system and stops the engine.
Your car has power saving system and stops the generator when cars battery is charged.
The card is wrongly formatted or too slow, fi les can’t be removed quickly.
Download the fi le to the PC fi rst. Format the SD-Card.
Download the fi le to the PC fi rst. Format the SD-Card.
Close the red jumper inside the CarCamOne-cable adaptor.
Close the red jumper inside the
CarCamOne-cable adaptor.
Format the card again using a professional formatting tool – see homepage. Use minimum class 4 cards
Make sure that the board plug provides voltage on position!
Please note that permanent improvements of the fi rmware cause adjustments on this manual.
On our website www.CamOneTec.com the latest version is available. Please pay attention on the version.
15
CarCamOne HD Accessories
Please note: CarCamOne HD shares accessories of the FlyCamOne HD 720p marked with „720”
Items marked with “1080” only cannot be used with the
CarCamOne HD!
Find more details at: www.CamOneTec.com
Docking station!
EAN
4260033049520
4260033049544
4260033049667
4260033049827
4260033049575
4260033049599
4260033049605
4260033049650
4260033049674
4260033047595
4260033049742
4260033049759
4260033049537
4260033049551
4260033049568
4260033049582
4260033049612
4260033049629
4260033049636
4260033049643
4260033049711
4260033049728
4260033049735
4260033049766
4260033047649
4260033049790
4260033049797
4260033049803
4260033049810
4260033049834
4260033049865
4260033048721
Art-No.:
FCHD14
FCHD21
FCHD22
FCHD23
FCHD26
FCHD64
FCHD28
FCHD29
FCHD30
FCHD31
FCHD33
FCHD37
FC3104
FCHD17
FCHD59
FCHD24
FCHD25
FCHD03
FCHD05
FCHD06
FCHD08
FCHD02
CCHD02
FCHD16
FCHD32
FCHD07
FCHD09
FCHD10
FCHD15
FCHD11
FCHD12
FCHD13
Item
FlyCamOne HD Screen 2,5”; 150cm cable
FlyCamOne HD / CarCamOne HD cable; 12-24V
FCHD Rapid Rush 16GB Micro SD-card
FCHD Rapid Rush 32GB Micro SD-card
FlyCamOne HD PIR Tube with 120cm cable
FlyCamOne HD Lens 133°
FlyCamOne HD Lens 170°
FlyCamOne HD GPS modul
FlyCamOne HD LiPo-battery; 3,7V 600mAh
FlyCamOne HD Cable 120cm
FlyCamOne HD Cable 200cm
FlyCamOne HD Tripod mount
FlyCamOne HD Transmission set 5.8GHz
FlyCamOne HD RX cable
FlyCamOne HD Battery; Li-Ion 900mAh
FlyCamOne HD V-Eyes set; incl. 2,4GHz remote
FlyCamOne HD 1080p myopia lens set
FlyCamOne HD V-Eyes base
FlyCamOne HD Docking station
FlyCamOne HD Remote
FlyCamOne HD AV cable
FlyCamOne HD Screen cable
FlyCamOne HD 5.8GHz adapter cable
FlyCamOne HD Pendulum mount (planes and kites)
FlyCamOne HD Handle bar mount
FlyCamOne HD Suction cup
FlyCamOne HD Belt clip
FlyCamOne HD Wrist mount (screen) spare
FlyCamOne HD DiveBox (up to 20m depth)
FlyCamOne HD Sportster headset
FlyCamOne HD Neoprene wristband for screen
5.8GHz Shield antenna + 500m
16
Compatible
Camera
1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720
720 & 1080
720 & 1080
720 & 1080
720 & 1080
720 & 1080
1080
720 & 1080
720 & 1080
720 & 1080
720
Space for your notes
17
Safety advice
Read the manual before using the product.
Information about the contained LiPo battery
!
When a battery is incorrectly replaced, there is danger of explosion. Replace the battery only by a battery that is recommended by the manufacturer of the same or equivalent type. Dispose used batteries according to the manufacturer’s instructions- Risk of fi re, explosions and burns.
Do not disassemble the battery. Do not heat the batteries above the following temperatures or incinerate them.
LiPo-Battery < 60° C
DE6989527
This product contains a LiPo battery. Dispose this batteries at a designated collection place only.
We hereby declare that this model meets the essential requirements and other relevant provisions of Directive 2004/108/EC. A copy of the Declaration of Conformity can be obtained from the address (p. 19).
Information for Users on Disposal of electrical and electronic equipment.
According to the company principles of CamOneTec / ACME the game company GmbH quality reusable components have been installed in this product. This symbol on the products and / or accompanying documents means that the product must be disposed at the end of the general household waste.
Dispose these products, the battery as well, at an environment- friendly collecting point
(or recycling yard)
Guarantee & warranty
The consumer is granted without prejudice to any claim against the seller a manufacturer’s
Guarantee under the following conditions:
» New devices and their components, resulting from manufacturing and / or material faults within
24 months from purchase, will be replaced by CamOneTec at its discretion charge against a statethe-art equipment or repaired for consumables (eg batteries, covers, etc.), this warranty is valid for 3 months from purchase.
» This warranty does not apply if the defect is due to improper handling and / or not following the instructions.
» This warranty does not extend to the customer themselves (eg installation, software downloads).
» Warranty claims are to be asserted immediately after the Guarantee default.
» Devices or components that are returned as part of the exchange to CamOneTec, become the property of CamOneTec.
» By services rendered under warranty does not extend the warranty period.
» Insofar as no Guarantee default exists, reserves CamOneTec, charge the customer for the replacement, repair or the shipping costs. The customer will be informed in advance.
18
Service & Support
CamOneTec by ACME the game company
Boikweg 24
33129 Delbrück
Germany
Telefon: +49 2944 97 383 0
E-Mail: [email protected]
http://www.camonetec.com
A list of our world-wide service points is available here:
http://www.camonetec.com/service
CamOne, FlyCamOne, CarCamOne and the CarCamOne Logo are registered Trademarks of ACME the game company, Germany
© copyright 2013 by ACME the game company GmbH
19
CamOneTec.com

Public link updated
The public link to your chat has been updated.
Advertisement