Allen-Bradley NEMA 4/12 Enclosure Kit Installation Instructions
PDF
Download
Document
Advertisement
Advertisement
Instructions 1336 PLUS and PLUS II IP 65/54 (NEMA Type 4/12) Enclosure Kit What this Option Provides The Enclosure Kit provides the required materials to enclose an open chassis 1336 PLUS or 1336 PLUS II in an enclosure. When properly installed, each Enclosure Kit is designed to meet IP 65 (NEMA Type 4) standards or IP 54 (NEMA Type 12) standards and permit the drive heatsink to extend outside the enclosure. You must observe the general installation requirements that are provided in the installation section of your drive User Manual. Where this Kit is Used The Enclosure Kit is used in the following ranges: Frame Reference A1, A2, A3 1 A4 B1 B2 C What the Kit Contains Enclosure Kit Catalog Number 1336S-AFA3, 1336S-AJA3 1336S-AFA4B, 1336S-AJA4B 1336-AFB1A, 1336-AJB1A 1336-AFB1B, 1336-AJB1B 1336-AFB1C, 1336-AJB1C 1336-AFB2A, 1336-AJB2A 1336-AFB2B, 1336-AJB2B 1336-AFB2C, 1336-AJB2C 1336-AFCA, 1336-AJCA 1336-AFCB, 1336-AJCB 1336-AFCC, 1336-AJCC Used with 1336 S/F . . . AQF05 - AQF50, BRF05 - BRF50 BRF75 - BRF100 A007 B007 - B015 C007 - C010 A010 - A015 B020 - B030 C015 - C020 A020 - A030 B040 - BX060 C025 - C060 Each IP 65 (NEMA Type 4) Enclosure Kit contains the following: • (1) Pre-assembled IP 65 (NEMA Type 4) enclosure with fan 1. • (1) IP 65 (NEMA Type 4) permanent adhesive backed gasket. • M5 x 0.08 x 10M sems or hex head screws. Each IP 54 (NEMA Type 12) Enclosure Kit contains the following: • (1) Pre-assembled IP 54 (NEMA Type 12) enclosure with fan 1. • (1) IP 54 (NEMA Type 12) permanent adhesive backed gasket. • 10-32 x 3/8 inch sems or hex head self-tap screws. 1 Fans are not required on A1, A2, and A3 frame enclosures. 2 1336 PLUS and PLUS II IP 65/54 (NEMA Type 4/12) Enclosure Kit To install the drive, follow these steps: ! ATTENTION: Electric shock can cause injury or death. Disconnect all power before working on this product. ! ATTENTION: Drive heatsink surface temperature may be at or near 100 degrees C (212 degrees F). To avoid burns, do not make contact with the drive heatsink. 1. Place the gasket, with the gasket paper still intact, around the cutout area on the inside of the enclosure. Assure that the mounting holes are aligned properly (mounting holes are not equally spaced). 2. Peel away the gasket paper. 3. Firmly press the gasket in place aligning with the enclosure holes. 4. Remove the screws holding the drive mounting rails to the drive back panel. 5. Install the drive in the enclosure using the mounting screws provided with the kit. 6. Torque all mounting screws to 2.9 N-m (26 lb.-in.). 7. Connect the fan wires (A4 Frames & Up) as shown in the next section. Wiring The following diagram shows the typical wiring diagram for all frames. Note that a fan is not required on A1-A3 frames. TB1 P P D D E E C C R S T U V W + – Typical Drive Location Pre-assembled Wires (Furnished) 115V 460V 0V 380V 0V 415V TB3 19 20 21 22 23 24 25 26 27 28 29 30 TB2 TETE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A1A2 TB1 P P D D E E C C R S T U V W + – J 2 T1 1 2 Fan Typical Transformer/Fan Location Typical Inside View Fan Typical Wire Connections (460V Connections Shown) 1336 PLUS and PLUS II IP 65/54 (NEMA Type 4/12) Enclosure Kit 3 IP 65/54 (NEMA Type 4/12) Dimensions A See Detail A D 12.4 (0.49) C F G H See Detail B E B 7.9 (0.31) 12.7 (0.50) 7.1 (0.28) Dia. 12.7 (0.50) 14.3 (0.56) Dia. Typical Top and Bottom Detail A 12.7 (0.50) Dia. Drive Heatsink 19.1 (0.75) All Dimensions in Millimeters and (Inches) Frame Reference A1 A2 A3 A4 B1 5.5 kW (7.5 HP) at 200-240V AC 11 kW (15 HP) at 380-480V AC B2 7.5-11 kW (10-15 HP) at 200-240V AC 15-22 kW (20-30 HP) at 380-480V AC C A 430.0 (16.93) 430.0 (16.93) 430.0 (16.93) 655.0 (25.79) 655.0 (25.79) 655.0 (25.79) 655.0 (25.79) 19.1 (0.75) Dia. Detail B B 525.0 (20.67) 525.0 (20.67) 525.0 (20.67) 650.0 (25.59) 650.0 (25.59) 900.0 (35.43) 1200.0 (47.24) C 350.0 (13.78) 350.0 (13.78) 350.0 (13.78) 425.0 (16.74) 425.0 (16.74) 425.0 (16.74) 425.0 (16.74) D 404.9 (15.94) 404.9 (15.94) 404.9 (15.94) 629.9 (24.80) 629.9 (24.80) 629.9 (24.80) 629.9 (24.80) E 500.1 (19.69) 500.1 (19.69) 500.1 (19.69) 625.1 (24.61) 625.1 (24.61) 875.0 (34.45) 1174.5 (46.22) F 250.0 (9.84) 250.0 (9.84) 250.0 (9.84) 293.0 (11.54) 293.0 (11.54) 293.0 (11.54) 293.0 (11.54) G N/A H N/A N/A N/A N/A N/A 63.5 (2.50) 63.5 (2.50) 63.5 (2.50) 63.5 (2.50) 76.2 (3.00) 76.2 (3.00) 76.2 (3.00) 76.2 (3.00) Approx. Ship Weight 16.8 kg (37.0 lbs.) 17.9 kg (39.4 lbs.) 18.6 kg (41.0 lbs.) 39.5 kg (87.0 lbs.) 44.7 kg (98.5 lbs.) 56.5 kg (124.5 lbs.) 80.7 kg (178.0 lbs.) Publication 1336 PLUS-5.66 – May, 1999 Supersedes February, 1996 P/N 74002-139-01 (01) Copyright 1999 Rockwell International Corporation. All rights reserved. Printed in USA. ">

Public link updated
The public link to your chat has been updated.
Advertisement