2007 ENGINE Lubrication [LF] - MX-5 Miata
2007 ENGINE
Lubrication [LF] - MX-5 Miata
LUBRICATION SYSTEM LOCATION INDEX [LF]
Fig. 1: Identifying Location Of Lubrication System Components
Courtesy of MAZDA MOTORS CORP.
ENGINE OIL LEVEL INSPECTION [LF]
1. Position the vehicle on level ground.
2. Warm up the engine.
3. Stop the engine and allow approx. 5 min. before continuing.
4. Remove the dipstick and verify that the oil level is between the F and L marks on the dipstick.
If the oil level is below the L mark, add engine oil.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 2: Identifying Mark On Dipstick
Courtesy of MAZDA MOTORS CORP.
ENGINE OIL REPLACEMENT [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
CAUTION:
In case you spill engine oil on the exhaust system, wipe it off completely. If you fail to wipe the spilled engine oil, it will produce fumes because of the heat.
1. Position the vehicle on level ground.
2. Remove the oil filler cap.
3. Remove the oil pan drain plug.
4. Drain the engine oil into a container.
5. Install the oil pan drain plug with a new washer.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 2 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Oil pan drain plug tightening torque
30-41 N.m {3.1-4.1 kgf.m, 23-30 ft.lbf}
NOTE:
The amount of residual oil in the engine can vary according to factors such as the replacement method and oil temperature. Verify the oil level after engine oil replacement.
6. Refill the following type and amount of the engine oil.
NOTE:
The maintenance intervals on scheduled maintenance table (See
SCHEDULED MAINTENANCE ) can only be supported with the use of the following oils.
ENGINE OIL SPECIFICATION
Item U.S.A. and CANADA Except U.S.A. and CANADA
Engine oil grade
API SL or ILSAC
Engine oil viscosity
Engine oil capacity (approx. quantity) (AT, 5MT)*
1
5W-20
Oil replacement: 3.9 L {4.1 US qt, 3.4 Imp qt}
Oil and oil filter replacement: 4.3 L {4.5 US qt, 3.8 Imp qt}
Total (dry engine): 4.6 L {4.9 US qt, 4.0 Imp qt}
Engine oil capacity (approx. quanity) (AT, 5MT)*
2
Oil replacement: 4.05 L {4.28 US qt, 3.56 Imp qt}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 3 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Oil and oil filter replacement: 4.45 L {4.70 US qt, 3.92 Imp qt}
Total (dry engine): 4.75 L {5.02 US qt, 4.18 Imp qt}
Engine oil capacity (approx. quanity) (6MT)
Oil replacement: 4.05 L {4.28 US qt, 3.56 Imp qt}
Oil and oil filter replacement: 4.55 L {4.81 US qt, 4.00 Imp qt}
Total (dry engine): 4.85 L {5.12 US qt, 4.27 Imp qt}
*
1
:Applied VIN (Assumed)
JM1 NC15F*7# 100001-130613
JM1 NC16F*7# 100001-130613
JM1 NC25F*7# 100001-130613
JM1 NC26F*7# 100001-130613
*
2
:Applied VIN (Assumed)
JM1 NC15F*7# 130614-
JM1 NC16F*7# 130614-
JM1 NC25F*7# 130614-
JM1 NC26F*7# 130614-
7. Install the oil filler cap.
8. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
9. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION [LF] .)
OIL PRESSURE INSPECTION [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 4 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
1. Remove the battery cover.
2. Disconnect the negative battery cable.
3. Remove the oil pressure switch.
4. Screw the SSTs into the oil pressure switch installation hole.
5. Connect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF] .)
6. Warm up the engine to normal operating temperature.
7. Run the engine at the specified speed, and note the gauge readings.
If not within the specification, inspect for the cause and repair or replace if necessary.
NOTE:
The oil pressure can vary with oil viscosity and temperature.
Fig. 3: Screwing SST Into Oil Pressure Switch Installation Hole
Courtesy of MAZDA MOTORS CORP.
Oil pressure (reference value) [oil temperature: 100°C {212°F}]
337-591 kPa {3.44-6.03 kgf/cm
2
, 49.0-85.8 psi} min [3,000 rpm]
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 5 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
8. Stop the engine and wait until it is cool.
9. Disconnect the negative battery cable.
10. Remove the SSTs.
CAUTION:
Make sure that there is no sealant between 1.0-2.0 mm {0.04-
0.07 in} from the end of the oil pressure switch to prevent a possible operation malfunction.
11. Apply silicone sealant to the oil pressure switch threads as shown in Fig. 4 .
12. Install the oil pressure switch.
Tightening torque
12-18 N.m {1.3-1.8 kgf.m, 9-13 ft.lbf}
13. Connect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [LF] .)
14. Install the battery cover.
15. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
Fig. 4: Applying Silicone Sealant To Oil Pressure Switch Threads
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 6 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Courtesy of MAZDA MOTORS CORP.
OIL FILTER REPLACEMENT [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
CAUTION:
In case you spill engine oil on the exhaust system, wipe it off completely. If you fail to wipe the spilled engine oil, it will produce fumes because of the heat.
1. Remove the oil filter using a commercially available, cup-type oil filter wrench (76 mm {3.0 in}
diameter, 15 sided).
2. Use a clean rag to wipe off the mounting surface.
3. Apply clean engine oil to the gasket of a new oil filter.
4. Tighten the oil filter using a cup-type oil filter wrench and according to the instruction on the package or side of the oil filter.
Tightening torque (reference value)
15-20 N.m {1.6-2.0 kgf.m, 11-14 ft.lbf}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 7 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 5: Removing Oil Filter
Courtesy of MAZDA MOTORS CORP.
5. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
6. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION [LF] .)
OIL PAN REMOVAL/INSTALLATION [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
1. Remove the battery and battery tray. (See BATTERY REMOVAL/INSTALLATION [LF] .)
2. Remove the air cleaner. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF] .)
3. Drain the engine oil. (See ENGINE OIL REPLACEMENT [LF] .)
4. Loosen the water pump pulley bolt and remove the drive belt. (See DRIVE BELT REPLACEMENT
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 8 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
[LF] .)
5. Remove the front suspension tower bar (joint, right side, and left side). (See FRONT SUSPENSION
TOWER BAR REMOVAL/INSTALLATION .)
6. Remove the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION [LF] .)
7. Remove the ignition coils. (See IGNITION COIL REMOVAL/INSTALLATION [LF] .)
8. Remove the P/S oil pump with the hose and pipe sill connected. Position the P/S oil pump out of the way.
(See POWER STEERING OIL PUMP REMOVAL/INSTALLATION .)
9. Remove the crankshaft position (CKP) sensor. (See CRANKSHAFT POSITION (CKP) SENSOR
REMOVAL/INSTALLATION [LF] .)
10. Remove the engine front cover. (See TIMING CHAIN REMOVAL/INSTALLATION [LF] .)
11. Remove the transverse member. (See TRANSVERSE MEMBER REMOVAL/INSTALLATION .)
12. Remove the member bracket. (MT) (See TRANSMISSION REMOVAL/INSTALLATION [M15M-
D] .) (See TRANSMISSION REMOVAL/INSTALLATION [P66M-D] .)
13. Remove in the order indicated in Fig. 6 .
14. Install in the reverse order of removal.
15. Refill the specified type and amount of the engine oil. (See ENGINE OIL REPLACEMENT [LF] .)
16. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
17. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION [LF] .)
18. Inspect for the ignition timing and idle speed. (See ENGINE TUNE-UP [LF] .)
Fig. 6: Identifying Oil Pan Components (With Torque Specifications)
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 9 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Courtesy of MAZDA MOTORS CORP.
OIL PAN REMOVAL NOTE
NOTE:
Lift up the engine approx. 25 mm {0.98 in} to assure clearance for the oil pan removal, then remove the oil pan.
1. Remove the windshield wiper arm. (See WIPER ARM AND BLADE
REMOVAL/INSTALLATION .)
2. Remove the cowl grille. (See COWL GRILLE REMOVAL/INSTALLATION .)
3. Remove the side cowl grille. (See SIDE COWL GRILLE REMOVAL/INSTALLATION .)
4. Remove the engine compartment service hole cover. (See EGR VALVE
REMOVAL/INSTALLATION [LF] .)
5. Remove the front tires.
6. Support the engine using the SST.
Fig. 7: Supporting Engine Using SST
Courtesy of MAZDA MOTORS CORP.
7. Remove the engine mount rubber installation nuts.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 10 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 8: Identifying Engine Mount Rubber Installation Nuts (With Torque Specifications)
Courtesy of MAZDA MOTORS CORP.
8. Lift up the engine approx. 25 mm {0.98 in} using the SST.
9. Remove the oil pan installation bolts.
10. Remove the oil pan using the separator tool.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 11 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 9: Removing Oil Pan Using Separator Tool
Courtesy of MAZDA MOTORS CORP.
11. Remove the oil pan.
OIL PAN INSTALLATION NOTE
CAUTION:
Apply the silicon sealant in a single, unbroken line around the whole perimeter.
Using bolts with the old seal adhering could cause cracks in the housing.
1. Completely clean and remove any oil, dirt, sealant or other foreign material that may be adhering to the housing and oil pan.
2. When reusing the oil pan installation bolts, clean any old sealant from the bolts.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 12 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 10: Identifying Old Sealant On Oil Pan Bolts
Courtesy of MAZDA MOTORS CORP.
3. Use a square ruler to align the oil pan and the cylinder block junction side on the engine front cover side.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 13 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 11: Aligning Oil Pan & Cylinder Block Junction Side On Engine Front Cover Side Using
Square Ruler
Courtesy of MAZDA MOTORS CORP.
4. Apply silicone sealant to the oil pan along the inside of the bolt holes as shown in Fig. 12 .
Thickness
2.2-3.2 mm {0.087-0.126 in}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 14 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 12: Applying Silicone Sealant To Oil Pan
Courtesy of MAZDA MOTORS CORP.
5. Tighten the bolts in the order shown in Fig. 13 .
Tightening torque
17-23 N.m {1.8-2.3 kgf.m, 12.6-16.9 ft.lbf}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 15 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 13: Identifying Tightening Sequence Of Oil Pan Bolts
Courtesy of MAZDA MOTORS CORP.
6. Tighten the oil pan-transmission installation bolts.
Tightening torque
37-52 N.m {3.8-5.3 kgf.m, 28-38 ft.lbf}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 16 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 14: Tightening Oil Pan-Transmission Installation Bolts
Courtesy of MAZDA MOTORS CORP.
OIL PUMP REMOVAL/INSTALLATION [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
1. Remove the battery and battery tray. (See BATTERY REMOVAL/INSTALLATION [LF] .)
2. Remove the air cleaner. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF] .)
3. Drain the engine oil. (See ENGINE OIL REPLACEMENT [LF] .)
4. Loosen the water pump pulley bolt and remove the drive belt. (See DRIVE BELT REPLACEMENT
[LF] .)
5. Remove the front suspension tower bar (joint, right side, and left side). (See FRONT SUSPENSION
TOWER BAR REMOVAL/INSTALLATION .)
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 17 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
6. Remove the plug hole plate. (See PLUG HOLE PLATE REMOVAL/INSTALLATION [LF] .)
7. Remove the ignition coils. (See IGNITION COIL REMOVAL/INSTALLATION [LF] .)
8. Remove the P/S oil pump with the hose and pipe sill connected. Position the P/S oil pump out of the way.
(See POWER STEERING OIL PUMP REMOVAL/INSTALLATION .)
9. Remove the crankshaft position (CKP) sensor. (See CRANKSHAFT POSITION (CKP) SENSOR
REMOVAL/INSTALLATION [LF] .)
10. Remove the engine front cover. (See TIMING CHAIN REMOVAL/INSTALLATION [LF] .)
11. Remove the transverse member. (See TRANSVERSE MEMBER REMOVAL/INSTALLATION .)
12. Remove the member bracket. (MT) (See TRANSMISSION REMOVAL/INSTALLATION [M15M-
D] .) (See TRANSMISSION REMOVAL/INSTALLATION [P66M-D] .)
13. Remove the oil pan. (See OIL PAN REMOVAL/INSTALLATION [LF] .)
14. Remove in the order indicated in Fig. 15 .
15. Install in the reverse order of removal.
16. Refill the specified type and amount of the engine oil. (See ENGINE OIL REPLACEMENT [LF] .)
17. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
18. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION [LF] .)
19. Inspect for the ignition timing and idle speed. (See ENGINE TUNE-UP [LF] .)
20. Inspect the oil pressure. (See OIL PRESSURE INSPECTION [LF] .)
Fig. 15: Identifying Removal Order Of Oil Pump (With Torque Specifications)
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 18 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Courtesy of MAZDA MOTORS CORP.
OIL PUMP SPROCKET REMOVAL/INSTALLATION NOTE
1. Temporarily install the crankshaft pulley and crankshaft pulley lock bolt to the crankshaft, and lock the oil pump against rotation as shown in figure.
Fig. 16: Installing SST To Oil Pump Sprocket
Courtesy of MAZDA MOTORS CORP.
2. Remove/install the oil pump sprocket, and then remove the crankshaft pulley lock bolt.
Tightening torque
20-30 N.m {2.1-3.0 kgf.m, 14.8-22.1 ft.lbf}
OIL PUMP INSTALLATION NOTE
1. Tighten the oil pump bolts in two steps in the order shown in Fig. 17 .
Tightening torque
Step 1: 8-12 N.m {82-122 kgf.cm, 71-105 in.lbf}
Step 2: 17-23 N.m {1.8-2.3 kgf.m, 12.6-16.9 ft.lbf}
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 19 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 17: Tightening Oil Pump Bolts
Courtesy of MAZDA MOTORS CORP.
OIL COOLER REMOVAL/INSTALLATION [LF]
WARNING:
Hot engine and engine oil can cause severe burns. Turn off the engine and wait until it and the engine oil have cooled.
A vehicle that is lifted but not securely supported on safety stands is dangerous. It can slip or fall, causing death or serious injury. Never work around or under a lifted vehicle if it is not securely supported on safety stands.
Continuous exposure to USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after working with engine oil.
1. Remove the battery cover.
2. Disconnect the negative battery cable.
3. Drain the engine coolant. (See ENGINE COOLANT REPLACEMENT [LF] .)
4. Remove the under cover. (See TRANSVERSE MEMBER REMOVAL/INSTALLATION .)
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 20 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
5. Remove the under guard. (LF engine MT models) (See TRANSMISSION
REMOVAL/INSTALLATION [P66M-D] .) (See TRANSMISSION REMOVAL/INSTALLATION
[M15M-D] .)
6. Remove the side cover. (LH)
7. Remove oil filter. (See OIL FILTER REPLACEMENT [LF].)
8. Remove in the order indicated in the table.
9. Use a clean rag to wipe off the mounting surface on the oil filter adapter and the oil cooler.
10. Install in the reverse order of the removal.
11. Refill the engine coolant. (See ENGINE COOLANT REPLACEMENT [LF] .)
12. Start the engine and confirm that there is no oil leakage.
If there is oil leakage, repair or replace the applicable part.
13. Inspect the oil level. (See ENGINE COOLANT LEVEL INSPECTION [LF] .)
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 21 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
Fig. 18: Identifying Oil Cooler Components
Courtesy of MAZDA MOTORS CORP.
OIL COOLER ITEM DESCRIPTION
1
2
3
4
OIL COOLER REMOVAL NOTE
Microsoft
Thursday, July 09, 2009 3:04:27 PM
Water hose
Oil pressure switch connector
Oil cooler and oil filter adapter component
Oil cooler
Page 22 © 2005 Mitchell Repair Information Company, LLC.
2007 Mazda MX-5 Miata Sport
2007 ENGINE Lubrication [LF] - MX-5 Miata
1. Secure the oil cooler and oil filter adapter component in a vise.
2. Loosen the oil cooler fitting bolt.
3. Remove the oil cooler.
Microsoft
Thursday, July 09, 2009 3:04:27 PM Page 23 © 2005 Mitchell Repair Information Company, LLC.
