Morrison 30cc petrol blower Owner's manual

PDF

Documento

Morrison Petrol Blower / Vac 30cc

Owner’s Manual

Important

Please read these instructions carefully before assembly, to reduce risk of fire, burn hazard or other injury.

Keep these instructions in a safe place for future use.

This manual covers the Morrison Petrol Blower Vac 30cc.

www.morrisonoutdoor.com

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

Part N o

: 542802

Revised May 2013

Do not operate this machine before it has been assembled correctly and you have read and understood these instructions.

These instructions are intended as a general guide and do not supersede national or local codes in any way. Contact local Authorities for clarity of laws relating to operation of this appliance.

Keep the instructions in a safe place for future use.

Parts Location

Warning labels on the machine

Symbols on the machine

Safety Instructions

For safe operation

Maintenance

Transportation

Parts location

Installation of the blower and vacuum tube

Fuel

Operation

Storage

Specifications

Additional Problems

6-7

7-9

2-3

3-5

Gasoline Blower and Vacuum 30cc

PARTS LOCATION

1. On / off switch

2. Deduction

3. Starter handle

4. Main handle

5. Spark plug

6. Motor

7. Throttle

8. Air Filter

9. Fuel Tank

10. Petrol cap

11. Sucker / blower selector lever

12. Leaves bag

13. Blowing and suction

14. Cause injection pump

WARNING LABELS ON THE MACHINE

WARNING! The blower can be dangerous!

Careless or improper use can cause serious, even fatal injury.

Read the operator’s manual carefully and make sure that you understand the contents before using the blower.

Wear eye and ear protection.

Always wear approved protective gloves.

Wear study, non-slip boots

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

Thrown or blown object. Stay a safe distance from the machine.

Warning! Keep away from hot surface

Important!

If warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s).

Warning!

Never modify your machine. The manufactures Warranty may be voided by any modification or incorrect use of this unit

SYMBOLS ON THIS MACHINE

Never allow the blower to run without the blower tube!

For safe operation and maintenance, symbols are in relief on the machine. According to these indications, please be aware of their meaning.

Warning! The blower can forcibly throw objects that can bounce back. This can result in serious eye injuries if the recommended safety equipment is not used.

The blower operator must make sure that no bystanders or animals come nearer than 50 feet (15 meters). Whenever several operators are working in the same work area, they should maintain a safe distance of at least 50 feet (15 meters) from one another.

The port to refuel the “MIX GASOLINE”,

Position: FUEL TANK CAP

The direction to close the choke. Position:

AIR CLEANER

The direction to open the choke. Position:

AIR CLEANER

The direction to the start of ignition switch. Position: IGNITION SWITCH ON

THE CONTROL HANDLE

The direction to stop the engine. Position:

IGNITION SWITCH ON THE CONTROL

HANDLE

Severing of fingers or hand by fan blade. Do not open or remove safety guards or nets while engine is running.

FOR SAFE OPERATION

No open flame!

No smoking!

Never work if people – especially children

– or animals are in the danger area.

Sound power level with EC Directive

2000/14/EC!

WARNING

1. Read this manual carefully until you completely understand and follow all safety and operating instructions.

2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.

3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

4. Do not lend or rent your machine without the owner’s manual.

5. Be sure that anyone using your unit understands the information contained in this manual.

6. Never let a child under 13 years old use the machine.

7. Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

8. Under no circumstances may the design of the machine be modified without the permission of the manufacturer.

Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others.

A blower is a dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

important that you read and understand the contents of this

Operator’s manual.

WORKING CONDITION

1. Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication.

2. To reduce the risk of hearing loss associated with sound level(s), hearing protection is required.

3. To reduce the risk of injury associated with thrown objects, always wear eye protection and foot protection.

4. To reduce the risk of injury associated with the inhalation of dust, use a face filter mask in dusty conditions.

5. Wear sturdy rubber-soled shoes or shoes with some other form of anti-slip protection to help protect you against falling.

6. To reduce the risk of injury associated with objects being drawn into rotating parts, do not wear loose clothing, scarves, neck chains, hair longer than shoulder length, or other loose material.

7. Prolonged use of a blower, exposing the operator to vibrations and cold may produce white finger disease

(Raynaud’s phenomenon), which symptoms are tingling and burning sensations followed by loss of color and numbness in the fingers. All factors which contribute to white finger disease are not known, but cold weather, smoking diseases or physical conditions as well as long periods of exposure to vibration are mentioned as factors. In order to reduce the risk of white finger disease, the following precautions are strongly recommended; a) Keep your body warm. Never use blower during

continuous rain.

b) Wear thick anti-vibration gloves.

c) Take more than 5 minutes of break in warm place

frequently.

d) Maintain a firm grip at all times, but do not squeeze

the handles with constant, excessive pressures.

e) If you feel discomfort, redness and swelling of your

fingers or any other part of your body, seek medical

advice.

The ignition system of your unit produces an electromagnetic field of a very low intensity. This field may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with a pacemaker should consult their medical practitioner before operating this tool.

be disturbed. Check and comply with times listed in local councils.

2. To reduce sound levels, limit the number of pieces of equipment used at any one time.

3. Operate power blowers at the lowest possible throttle speed to do the job.

4. Check your equipment before operation, especially the muffler, air intakes and air filters.

WORKING PLAN

When planning your work schedule, allow plenty of time to rest. Limit the amount of time over which the product is to be used continuously to somewhere around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of rest between work sessions. Also try to keep the total amount of work performed in a single day under 2 hours or less.

FUEL WARNING

To reduce the risk of fire and burn injury:

a) Handle fuel with care. It is highly flammable.

b) Do not smoke while handing fuel.

c) Do not refuel a hot engine.

d) Do not refuel a running engine.

e) Avoid spilling fuel or oil. Always wipe unit dry before using.

f ) Move at least 10 ft. (3 meters) away from the fueling point

before starting engine.

g) Always store gasoline in a container approved for

flammable liquids.

h) Make sure the unit is properly assembled and in good

operating condition.

i ) Do not use the blower near a fire, as aiming the blower in

the direction of a flame may cause flammable substances

to scatter in other areas and ignite.

BEFORE STARTING THE ENGINE

Each time before starting the engine, inspect the entire unit to see if every part is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repaired.

IMPORTANT

Before starting operation, always make sure to check if any obstacles are left inside the volute case and leaves bag. The obstacles may cause damage to the fan and volute case and could potentially also cause serious injury.

WORKING CIRCUMSTANCE

1. To reduce the risk of injury associated with exhaust fume inhalation, do not operate in any unventilated area. The exhaust gases contain harmful carbon monoxide.

2. Avoid using the blower where stable footing and balance are not assured.

3. Never operate the machine in high wind, bad weather, potentially explosive atmosphere, when visibility is poor or in very high or low temperatures. (Our recommended use environment is below 40 degrees C (104 degrees F).)

WARNING

Never remove debris from the blower and vacuum tube while the engine is running. Contact with rotating blower fan may result in a serious personal injury.

WARNING

To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. Do not operate without the leaves bag in place. Always disconnect the spark plug before performing maintenance or accessing movable parts.

AVOID NOISE PROBLEM

IMPORTANT

Check and follow the local regulations as to sound level and hours of operations for blower.

1. Operate power equipment only at reasonable hours-not early in the morning or late at night when people might

USING THE PRODUCT WARNING

WHILE USING THE PRODUCT, IF ABNORMAL

NOISE OR VIBRATION OCCURS, STOP THE ENGINE

IMMEDIATELY AND CONTACT THE NEAREST

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

SERVICING DEALER FOR ASSISTANCE. CHECKING

THE FAN IS VERY IMPORTANT. IF THE ROTATING FAN

SHOULD BREAK UP, IT MIGHT LEAD TO SERIOUS

ACCIDENTS.

1. This blower is a handheld type. It is operated and controlled with the handle by hand.

2. Check the work area that the blower will be used in and remove or cover all valuables that may be damaged by the air blast or thrown debris.

3. Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

4. To reduce the risk of injury associated with thrown objects.

a) Watch out for children, pets, open windows or

freshly washed cars, and blow debris safely away.

b) Do not allow bystanders in work area.

c) Do not point the blower tube in the direction of

people or pets.

d) Always check to be sure that no debris has been

blown onto someone else’s property.

e) Pay attention to the direction of the wind. Do not

work against the wind.

f) Never point a blower tube toward an open flame

to avoid the possibility of igniting the unit, causing

injury to yourself or damage to surroundings.

5. To minimize blowing time.

a) Use rakes and brooms to loosen debris before

blowing.

b) In dusty conditions, slightly dampen the surface.

c) Conserve water by using power blowers instead

of hoses for many lawn and garden applications,

including areas such as gutters, screens, patios,

grills, porches and gardens.

6. The blower must not be used while on a ladder or scaffolding.

7. Never put the machine down with the engine running unless you have it in clear sight.

8. Never to touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock.

9. Never to touch the muffler, spark plug, or other metallic parts of the engine or engine cover while the engine is in operation or immediately after shutting down the engine. These metallic parts and engine cover reach high temperatures during operation and doing so could result in serious burns.

MAINTENANCE

1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals.

2. Always be sure to turn off the engine and disconnect the spark plug before performing any maintenance or checking procedures.

WARNING

THE METALLIC PARTS AND ENGINE COVER REACH

HIGH TEMPERATURES IMMEDIATELY AFTER

STOPPING THE ENGINE.

3. Examine the blower at intervals for loose fasteners and rusted or damaged parts. Use special care around the fuel line, the muffler, and the ignition wiring.

4. All engine service except for those described in this manual should be performed by competent service personnel. Improper service to the blower fan and muffler could cause a hazardous failure.

5. In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest servicing dealer for assistance.

6. Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

TRANSPORTATION

• Drain the fuel from the fuel tank before transporting or storing the blower.

• Secure the unit carefully to prevent movement when it is transported.

• A unit that receives a strong shock during transport and unloading may malfunction.

STORAGE

• When storing the blower, choose a space indoors free from moisture and out of the reach of children.

DISPOSAL

• When you dispose of the machine, do not disassemble the machine.

• When disposing of your machine, fuel or oil from the machine, be sure to follow your local council regulations.

WARNING

THE TEMPERATURE OF THE MACHINE MAY

INCREASE AFTER STOPPING THE ENGINE.

ESPECIALLY NEVER FORGET TO COOL DOWN

THE ENGINE BEFORE REFUELING THE MACHINE.

SET UP

WARNING

Stop the machine and place the on / off switch to OFF before you make adjustments, or the device is no longer in use.

Failure to comply could result in serious personal injury

10. After using blowers and other equipment, CLEAN UP!

Dispose of debris in trash receptacles.

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

FUEL

Gasoline Blower and Vacuum 30cc

PARTS LOCATION

INSTALLATION OF THE BLOWER AND

VACUUM TUBE

INSTALLATION OF THE BAG

1. Push the bag adapter into the case.

2. Place the bag ring on the hook of the device.

3. Make sure that the bag is zipped closed before turning on the unit

WARNING!

• Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m

(10 ft) away from the fueling point before starting the engine.

• The engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. using an antioxidant added quality oil expressly labeled for air-cooled

2-cycle engine use (JASO FC GRADE OIL or ISO EGC

GRADE).

• Do not use BIA or TCW (2-stroke water-cooling type) mixed oil.

1. On / off switch

2. Throttle

3. Starter handle

4. Main handle

5. Spark plug

6. Motor

7. Choke lever

8. Air Filter

9. Fuel Tank

10. Petrol cap

11. Sucker / blower selector lever

12. Leaves bag

13. Blowing and suction

14. Primer pump

1. Align groove in pipe end with projection on straight tube and slide the pipe onto the straight pipe. Tight the screws.

2. Release the screw and insert the blower and vacuum tube into the blower housing and tight the screws.

3. Insert the speed wheel on the end of blower and vacuum tube.

RECOMMENDED MIXING RATIO GASOLINE 40 : OIL 1

• These engines are certified to operate on unleaded gasoline.

• Make sure to use gasoline with a minimum octane number of 89RON.

• If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

• Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

• Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitation.

1. Measure out the quantities of gasoline and oil to be mixed.

2. Put some of the gasoline into a clean, approved fuel container.

3. Pour in all of the oil and agitate well.

4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5. Indicate the contents on outside of container for easy identification. To avoid mixing up with gasoline or other containers.

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the cap on a dustless place.

2. Put fuel into the fuel tank to 80% of the full capacity.

3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING!

1. Select bare ground for fueling.

2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine.

3. Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

4. Do not smoke or place any hot objects near fuel.

FOR YOUR ENGINE LIFE, AVOID:

1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.

5. In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6. In the case of disposing the used mixed oil container, take it to an authorized collection site.

RESTARTING ENGINE WHILE ENGINE IS HOT

1. When restarting the engine immediately after stopping it, leave the choke open.

2. If the engine won’t start after several attempts, close the choke and repeat pulling the rope or remove the spark plug and dry it.

ADJUSTING IDLE SPEED

When the engine tends to stop frequently at an idle mode, turn the adjusting screw clockwise.

NOTE: Warm up the engine before adjusting the idle speed.

STOPPING ENGINE

Move the throttle lever to the idling position and move the ignition switch to “0 (STOP)” position.

NOTE: Except for an emergency, avoid stopping the engine while pulling the throttle trigger.

OPERATION

STARTING ENGINE

1. Rest the unit on a flat, firm place.

2. Pump the primer until fuel flows out in the clear tube

(photo 4, 3).

3. Set the “on/off” button on the “I” position (photo 1).

4. Move the chock lever upward to close position (photo 2).

5. Holding the blower handle, pull the starter rope with your hand. Hold the throttle during use (photo 5).

IMPORTANT

• Avoid pulling the starter rope out to its full extent and allowing the starter rope to snap back. This will prevent premature damage to the starter.

• Do not let a person stand near the blower or the exhaust port.

6. When the engine has started, move the choke lever gradually downward to open the choke.

7. Allow the engine to warm up for a half minute before starting operation.

SWITCHING BETWEEN SUCTION AND BLOWER MODE

You can either blow or suck with this equipment.

• To activate blower mode slide the suction/blower lever to the right

• To activate suction mode slide the suction/blower lever to the front.

BLOWER OPERATION

Your blower is designed to easily remove debris from patios, walkways, lawns, bushes, etc., and many hard to reach areas where debris may accumulate.

WARNING: Because of flying debris, always wear safety glasses or face shield when operating the blower.

Before using your blower, review Safety Operation in your

User Manual, and all regulations for operation of the unit.

These precautions and regulations are for your protection.

CAUTION: Hold the blower so that the hot exhaust does not damage clothing and is not inhaled by the operator.

DO NOT operate the blower with other people or animals in the immediate vicinity. Allow a minimum of 30 feet (9 meters) between operator and other people or animals.

We recommend that a face mask be worn when operating blower in dusty areas. Stand away from the debris, at a distance that will easily allow you to control the direction of blown debris. Never blow debris in direction of bystanders.

To control velocity of airstream, blower can be operated at any speed between idle and full throttle. Experience with the unit will help you determine the amount of airflow necessary for each application.

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

VACUUM OPERATIONS

WARNING: NEVER OPERATE VACUUM WITHOUT

VACUUM BAG PROPERLY ATTACHED, AS FLYING

DEBRIS COULD CAUSE INJURY TO OPERATOR AND

BYSTANDERS. ALWAYS MAKE SURE VACUUM BAG

ZIPPER IS CLOSED BEFORE OPERATING UNIT.

Do not vacuum hot or burning materials (e.g. hot ash, glowing cigarettes) from outdoor fireplaces or barbecue pits.

Always wait for these materials to be cool enough. Do not vacuum lighted smoking material such as discarded cigars or cigarettes. Do not operate unit near open flame.

CAUTION: This unit is designed to vacuum up debris such as leaves, small bits of paper, small twigs, weeds, grass clippings, etc. Do not use this unit for any other purpose.

Do not attempt to vacuum rocks, broken glass, bottles, tin cans or other such objects. Damage to impeller and unit as well as operator injury could result. If vacuum tube is level with power unit horizontal, rocks or large objects may be drawn into tube, damaging the impeller.

some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment.

Ensure that no water can seep into the device.

VACUUM BAG

A dirty bag will obstruct airflow, thereby reducing vacuum efficiency.

TO CLEAN BAG:

1. Detach vacuum bag from unit.

2. Open zipper and remove contents.

3. Turn bag INSIDE OUT and shake vigorously. This procedure should be performed on a regular basis.

4. Turn bag RIGHT SIDE OUT, close zipper and attach to unit.

NOTE: If vacuum bag is unusually dirty, it should be washed by hand in warm water with a mild detergent. Rinse thoroughly. Let dry before using.

AIR FILTER

TO OPERATE VACUUM

1. Follow correct starting procedures as explained in this manual.

2. Leave the motor running at idle speed. Attach the shoulder strap so that it lies over the left shoulder.

CAUTION: Do not allow shoulder harness to cover, block, or come in contact with exhaust outlet during operation. The muffler generates heat and could burn, melt, or damage harness strap.

3. Hold the appliance with the right hand on the upper handle and with the left hand on the front handle.

4. For suction, swing the appliance from side to side.

CAUTION: To avoid clogging vacuum tube. DO NOT

FORCE OR PLACE SUCTION TUBE INTO A PILE OF

DEBRIS.

VACUUM TUBE CLOGGING

TO UNCLOG VACUUM TUBE:

Turn engine “OFF”. Promptly compress vacuum bag while it is still inflated, expelling air out of the suction tube. This reverse airflow is usually sufficient to dislodge most obstructions. If the obstruction cannot be cleared by compressing vacuum bag, follow this procedure:

• Remove and inspect vacuum tubes.

• Carefully clean out nozzle.

• Reinstall vacuum tubes.

MAINTENANCE

WARNING!

Always switch off the equipment and pull out the spark plug before carrying out any maintenance work. Contact with rotating blower fan or hot muffler may result in a personal injury.

CLEANING

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

• We recommend that you clean the device immediately each time you have finished using it.

• Clean the equipment regularly with a moist cloth and

Soiled air filters reduce the engine output by supplying too little air to the carburetor.

Regular checks are therefore essential. The air filter should be checked after every 25 hours of use and cleaned if necessary. If the air contains a lot of dust, the air filter should be checked more frequently.

1. Remove the air filter cover

2. Remove the filter element

3. Clean the filter element by tapping it or blowing it.

4. Assemble in reverse order. Never forget to attach the screen. If the screen is not attached, the cleaner will not seal properly and the dusts come into the cylinder.

NOTE:

Never clean the air filter with petrol or inflammable solvents.

FUEL FILTER

A clogged fuel filter may cause poor acceleration of the engine. Check periodically to see if the filter is clogged with dirt. The filter can be taken out of the fueling port using a small wire hook (not supplied). Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it.

Clean the components with gasoline.

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

SPARK PLUG

STORAGE

Spark plug gap = 0.6 mm. Tighten the spark plug with a torque of 12-15 Nm.

Check the spark plug for dirt and grime after 10 hours of operation and if necessary clean it with a copper wire brush.

Thereafter service the spark plug after every 50 hours of operation.

1. Pull off the spark plug boot by twisting.

2. Remove the spark plug with the supplied spark plug wrench.

3. Assemble in reverse order.

MUFFLER

WARNING

• Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, do not use the blower and have it repaired immediately.

• Note that failing to do so may result in the engine catching on fire.

IMPORTANT

• Before starting operation, always make sure to check if the muffler is properly held by three bolts to the cylinder.

(Fastening Torque : 8~12 N·m)

• Even if one bolt out of three bolts is loose, the muffler may get loose during operation which may result in engine catching on fire.

PROCEDURES TO BE PERFORMED AFTER EVERY 50

HOURS OF USE

1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.

2. Tighten all screws, bolts, and fittings.

BEFORE STORING THE BLOWER:

1. Drain a fuel tank and push the primer bulb until it becomes empty of fuel.

2. Remove the spark plug and drop a spoonful of 2-cycle oil into the cylinder. Crank the engine several times and install the spark plug.

3. Store unit in a dry, dust free place, out of the reach of children.

DISPOSAL

• When you dispose of the machine, do not disassemble the machine.

• When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.

SPECIFICATIONS

Engine model: 1E37F

Engine displacement: 30cc

Max power:

Max speed:

0.75kw

9600rpm

Idle speed: 3500rpm

Blowing wind speed: 175km/h

Vacuum wind speed: 95km/h

Fuel tank capacity:

Bag capacity:

Gas/Oil Rate:

Sound power level:

Vibration:

450ml

40L

40:1

110dBA

14.059m/s 2

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

SYMPTOM

Poor acceleration.

Engine stops abruptly.

Engine difficult to shut off.

Excessive vibration.

ADDITIONAL PROBLEMS

POSSIBLE CAUSE

Clogged air cleaner element.

Clogged fuel filter.

Carburettor mixture too lean.

Idle speed set too low.

Fuel tank empty.

Clogged fuel filter.

Water in the fuel.

Shorted spark plug or loose terminal.

REMEDY

Clean the element.

Replace the fuel filter as required.

Return blower to the dealer.

Adjust: 3500 rpm.

Refuel.

Clean or replace the fuel filter as required.

Drain; replace with clean fuel.

Clean and replace spark tighten the terminal.

Return blower to the dealer.

Test and replace as required.

Ignition failure.

Piston seizure.

Ground (stop) wire is disconnected, or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine.

Warped or damaged blower fan.

Loose bolt or fastener.

Internal engine damage.

Correct plug: Champion

Idle engine until cool.

Inspect and replace fan as required.

Tighten as required.

Return blower to dealer.

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

Head Office - New Zealand

1-37 Mt Wellington Highway, Panmure, Auckland 1060

P.O. Box 14 349, Panmure, Auckland 1741

542802 - Morrison Petrol Blower Vac 30cc Owner’s Manual - May ‘13

Pantone 1797C

Ciao! Sono un chatbot AI specificamente addestrato per assisterti con il Morrison 30cc Manuale del proprietario. Ho esaminato attentamente il documento e posso aiutarti a individuare le informazioni di cui hai bisogno o spiegare il contenuto in termini chiari e semplici. Che tu stia cercando indicazioni su funzionalità specifiche, passaggi per la risoluzione dei problemi o l'uso generale, non esitare a fare domande. Più dettagli fornisci sulle tue esigenze o dubbi, più accuratamente e efficacemente potrò aiutarti!

L''assistente sta scrivendo

L''assistente non è disponibile. Riprova più tardi.

Sembra che tu sia arrivato a un documento scritto in più lingue, inclusa una che non è la tua lingua madre. Puoi utilizzare i seguenti collegamenti per nascondere temporaneamente le pagine senza la lingua che preferisci.