Wilson Electronics AG Pro 70 Specification

Wilson Electronics AG Pro 70 Specification
Adjustable Gain
Signal Boosters
AG Pro 75™, AG Pro 70™, AG Pro Installer™,
AG SOHO 65™, AG SOHO 60™
(SOHO: Small Office, Home Office)
In-Building Wireless 800/1900 MHz
Smart Technology ™
Contents:
Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Outside Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Finding the Strongest Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Inside Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing a Wilson Electronics Signal Booster . . . . . . . . . . . . . . . . 9
Powering up a Wilson Electronics Signal Booster. . . . . . . . . . . . 9
Understanding the Signal Booster Lights. . . . . . . . . . . . . . . . 10
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . 13
Guarantee & Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Appearance of device and accessories may vary.
Note: This manual contains important safety and operating
information. Please read and follow the instructions in this
manual. Failure to do so could be hazardous and result in
damage to your Signal Booster.
Wilson
®
Electronics, Inc.
Installation Instructions for the Following
Wilson Electronics Signal Boosters:
AG Pro 75™, AG Pro 70™, AG Pro Installer™& AG SOHO 65™,
AG SOHO 60™ In-Building Wireless 800/1900 MHz
Smart Technology ™ Signal Boosters
Model # 271265
FCC ID: PWO271265
IC: 4726A-271265
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver
service levels consistent with what would be expected in areas of high cell
network coverage. They amplify a weak or shadowed signal in mobile,
marine and in-building applications. When using a Wilson Electronics
Signal Booster in conjunction with Wilson Electronics antennas, the
Outside Antenna will collect the cell tower signal and send it through
the cable to the Signal Booster. The signal is then amplified and retransmitted through the Inside Antenna into the room. Cell phones and
cellular data cards in that area then communicate with the improved
signal. When a cell phone or cellular device transmits, the signal is
received by the Inside Antenna, amplified by the Signal Booster and
transmitted back to the cell tower through the Outside Antenna.
Inside this Package
Note: Kits may contain different accessories
AC/DC
Power
Supply
Outdoor Antenna Options
1. 1900 MHz Yagi PCS Antenna (301124)
2. 800 MHz Yagi Cellular Antenna (301129)
3. Wide Band Directional Antenna 700 MHz 2700 MHz (304411)
1
2
Signal
Booster
N Female - FME
Female Adapter
(Sold with the
AG SOHO 60)
(The AG Pro Installer
has a different knob
configuration)
Indoor Antenna Options & Accessories
A. Wide-Band Panel Antenna 700-2700MHz (301155)
B. 50 Ohm Lightning Surge Protector N-Connector (859902)
C. 75 Ohm Lightning Surge Protector F-Connector (859988)
Splitter options on page 8
3
A
B
C
Appearance of device and accessories may vary.
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Install Overview
See Installation Diagram on page 3. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.
1. Select a location to install the Signal Booster that is away from excessive
heat, direct sunlight, moisture and has proper ventilation. Do not place the
Signal Booster in an air-tight enclosure.
2. Select a location on the roof of the building to install the Outside Antenna.
Use a cell phone in test mode to find the strongest signal from the cell
tower (see page 6). Visit www.WilsonElectronics.com to find test mode
function for your particular cell phone.
3. Run the Outside Antenna cable to the Signal Booster and attach it to
the connector labeled “Outside Antenna” on the Signal Booster. Run the
Inside Antenna cable to the Signal Booster and attach it to the connector
labeled “Inside Antenna” on the Signal Booster. For more information on
running cable (see page 7). Lightning Surge Protection is recommended
for all in-building installations (see page 6).
4. Select a location for the Inside Antenna, preferably in the center of
where the signal needs to be amplified. A minimum separation distance
of 20 vertical (within the null zone) or 50 horizontal feet is necessary
for proper operation. If the inside coverage is not sufficient you may
need to increase the separation distance even further (see installation
diagram on pages 3 & 4).
5. Before powering up the Signal Booster, verify that both the Outside
Antenna and the Inside Antenna are connected and check that all
connections are tight. Note: Be careful when plugging the connectors
in so as not to bend the center pins on the connectors (see page 9).
6. The Signal Booster has been packaged with the gain control knobs
adjusted to the highest gain position. If one or both of the lights are not
green, please refer to pages 10-12. For AG Pro Installer (see page 12).
Warning: Connecting the Signal Booster directly to a cell phone with
use of an adapter will damage the cell phone and/or the Signal Booster.
IMPORTANT NOTICE
• It is very important to power your Signal Booster
using a surge protected AC Power Strip with at
least a 1000 Joule rating.
• Failure to do this will void your warranty in the
event of a power surge or lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Installation Diagram
Outside
Antenna
Inside Antenna
Preferred Method: Place the Inside
Antenna in the ceiling facing down for
the best coverage.
Note: The Inside Antenna may be
mounted on the wall directly under the
Outside Antenna, in the null zone, if
20 feet of vertical separation can be
maintained.
Null Zone: The area under the
Outside Antenna, where the
Outside Antenna radiates the
least.
Note: A Lightning Surge Protector is
recommended for all building installations
(sold separately). Make sure the protector
is installed in line between the Outside
Antenna and the Signal Booster.
Inside Antenna
(Optional
second
antenna for
additional
coverage).
Power
Supply
Typical Installation
3
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal
Booster. It is important to read through all of the installation steps
for your particular application prior to installing any equipment.
Read through the instructions, visualize where all the equipment will
need to be installed and do a soft installation before mounting any
equipment. Contact Wilson Electronics Technical Support with any questions
at: 866-294-1660.
Splitter
(if using multiple
inside antennas)
Lightning
Surge Protector
(recommended)
Inside Antenna
(Optional
third antenna
for additional
coverage).
Signal
Booster
Surge Protector
Powerstrip
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
4
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the frustration
of not being able to connect to or maintain a strong cellular signal. When
this occurs, it is generally due to one of two reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated to
provide broad coverage; however, there are many areas in which
signal strength may be reduced by topographic features or by local
government restrictions on the height or placement of the towers
themselves. Rural areas generally have fewer cell towers than urban
regions.
2. Natural and Man-Made Obstructions – Signal strength can also
be negatively affected by trees, hills, buildings, weather, and other
obstructions. You may be relatively close to a cell tower but still unable
to make a call. This often occurs in homes, offices and other buildings
in which stucco, concrete or metal walls may block the signal.
The Signal Booster works with two antennas. The Inside Antenna
communicates with your cell phone and the Outside Antenna
communicates with the cell tower. The Outside Antenna receives the cell
tower signal and sends it through the cable to the Signal Booster, where it
is amplified and re-transmitted much stronger through the Inside Antenna
into the room. When the Inside Antenna picks up a signal from your
cellular device, the Signal Booster amplifies that signal and transmits it
through the cable to the Outside Antenna and back to the cell tower.
Note: The Signal Booster will only operate if there is an adequate signal to amplify.
Outside Antenna Installation (part #304411 shown)
Antenna
Cell Tower
Drip hole on bottom
Cell Tower
The antenna should be mounted as shown in the illustration above.
The mounting bracket, included with antenna, is adjustable and will
accommodate pipe diameters from 1.25” to 2” (pipe sold separately part#
901117). Mount the antenna so that there is at least 3 feet of clearance in
all directions around it. Position the antenna so that it has an unobstructed
line of sight to the cell tower’s strongest signal. Make sure the antenna
is not pointing across your own roof or at the Inside Antenna as this will
cause the oscillation protection circuitry to shut down the Signal Booster
(see page 10).
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Warning: Lightning protection is recommended for all installations (sold separately part #859902 or 859988). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines.
Installing
Lightning Protection
(sold separately)
Install the Lightning Surge
Protector (LSP) close to the Signal
Booster. Attach the cable from
the Outside Antenna to the surge
protector, using a short length of low
loss cable; attach one end to the
LSP and the other to the Outside
Antenna connector on the Signal
Booster. Ensure the LSP is properly
grounded (ground wire not included).
(For AG Pro 70 use part# 859988-75
Ohm Lightning Surge Protector).
Visit www.WilsonElectronics.com
or call 800-204-4104 to purchase.
To Outside
Antenna
Lightning
Surge Protector
(sold separately)
Ground Wire
(not included)
To Inside
Antenna
Signal Booster
Surge Protector
Power Strip recommended for all AC power supplies
Selecting a Direction for the Outside Antenna
Select a location on the roof of the building to install the Outside Antenna.
Use a cell phone in test mode to find the strongest signal from the cell tower
(see below for more information). To get the strongest signal possible, it is
very important to set up your Outside Antenna properly. The Inside and the
Outside Antenna must be mounted in such a way that they are able to pick
up the best possible cell signal on the outside of the building and provide the
best possible signal on the inside of the building. Mount the Outside Antenna
as high as possible facing the cell tower in an area with the best possible
signal coverage.
Note: Never point the front of a Directional Antenna toward the Inside Antenna. See Figures 1 & 2 on page 10.
Finding the Strongest Signal
When installing your Signal Booster’s Outside Antenna, aiming it towards
the best signal source from you service provider is important. The best way
of getting the strongest signal is to have one person on the roof to rotate
the Outside Antenna, which is connected to the Signal Booster. Turning the
Outside Antenna about 45 degrees at a time, while the second person is
watching the signal strength on the phone inside the building. This allows
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
6
you to read the signal strength from the cell tower. It is preferable to have
the phone in the test mode so the actual signal strength can be read,
as bars are not the most accurate. Go to www.WilsonElectronics.com
for help in finding the test mode for your phone. Always make sure the
person inside the building gives the signal time to arrive and register
on the phone (between 10-30 seconds for phone to reset to the signal
reading).
Cell Signal
Outside
Wide Band
Antenna
Cell Tower
Signal Strength Graph
EXCELLENT
-50dB
-60dB
GOOD
-70dB
-80dB
POOR
-90dB
-100dB
NO
SIGNAL
-110dB
Signal readings usually appear as a negative number (for example, -86).
The closer you get to zero the stronger the signal (see graph above).
Mounting Tips for Running Outside
Antenna Cable
If you are mounting the Outside Antenna on the roof of your building, we
have found that it is easiest to run your cable underneath the down side
of your roof’s flashing. If you have satellite TV service installed you may
be able to follow the same route as the satellite TV cables that are already
running from outside of your building to the inside.
After routing the cable, we recommend sealing any areas where the cable
passes into the building with cable bushings, silicone or other waterproof
sealant to keep your installation from leaking. If you are mounting the
Outside Antenna to the outside wall of your home or building, the simplest
way is to run the cable on the outside of the wall and attach it to the
exterior of your home or office. Then drill a hole through the wall where you
want the cable to appear on the inside of the building. Before drilling, make
sure that there are no electrical outlets, sewer or water pipes, or electrical
wiring in the wall that you are about to drill through as this could potentially
harm you or damage the building.
7
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
After drilling the required hole, run the cable through and seal it with cable
bushings, silicone or other waterproof sealant to enclose the hole that you
have created. In some instances, it may be possible to run the cable up
into the fascia of the attic overhang. In this circumstance, the cable will be
accessible in the attic for further routing.
Installing the Inside Antenna
(Instructions are for optional Panel Antenna)
Select a location for the Inside Antenna, preferably in the center of where
the signal needs to be amplified. A minimum separation distance of 20
vertical feet is necessary for operation. If the inside coverage is not
sufficient you may need as much as 75 feet of horizontal separation. See
installation diagram on pages 3 & 4.
Inside
Antenna
Ceiling
Drywall
Ceiling
Rafters
In some cases, multiple Inside Antennas may be required, for instance if
you have multiple rooms with poor signal. A signal may be split by using
a splitter (sold separately). If using more than one Inside Antenna, a
separation up to 75 horizontal feet may be necessary between Inside
Antennas. See configuration on pages 3 & 4.
Warning: An Inside Antenna must have a separation distance from all persons that is at least 15 inches for the Panel Antenna.
Optional Wide
Band Inside
Antenna (sold
separately)
Splitter Options:
2-way
(859957)
3-way
(859980)
(sold separately)
4-way
(859981)
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
8
Installing a Wilson Electronics Signal Booster
Select a location to install the Signal Booster that is away from excessive
heat, direct sunlight, moisture and that has proper ventilation. Do not
place the Signal Booster in an air-tight enclosure. Recommended
installation locations for in-building Signal Boosters are near a power
outlet and in a closet or on a shelf.
Note: It is important to have adequate air ventilation. Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging the connector in so as not to damage the center pins on the connectors.
Run the Outside Antenna cable to the Signal Booster and attach it to
the connector labeled “Outside Antenna” on the Signal Booster. Run the
Inside Antenna cable to the Signal Booster and attach it to the connector
labeled “Inside Antenna” on the Signal Booster.
Note: For distances of 20 feet or more, use Wilson low loss cable.
Powering up a Wilson Electronics
Signal Booster
1. Never point the front of a Directional Outside Antenna toward the Inside
Antenna. See Figures 1 & 2 on page 10.
2. Ensure that both the Outside Antenna cable and the Inside Antenna cable
are connected to the Signal Booster and the connections are tight
before powering up the Signal Booster.
3. Plug the power supply into the Signal Booster input marked “6V DC”
(carefully, to avoid damaging the center pin) and then into a wall outlet.
Note: Wilson® Electronics recommends that all AC power supplies for
home electronics be plugged into a Surge Protector Power Strip.
4. If the Signal Booster does not have a green light(s), please see pages 1012. See page 12 for AG Pro Installer.
5. If you know that only one frequency band (800 or 1900) is available in
your coverage area (or going to be used), reduce the gain control on the
frequency band that is NOT in use to the lowest setting. This will reduce
the power consumption of the Signal Booster.
6. Using multiple Signal Boosters in one installation could cause interference
to the cell tower (except for the In-Line Signal Booster).
7. Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email [email protected] Technical Support
hours are Mon.- Fri. 7 am to 6 pm MST.
9
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Figure 2
Figure 1
CORRECT INSTALLATION
Point antennas away from each other
Outdoor
Antenna
INCORRECT INSTALLATION
Never point antennas toward each other
Outdoor
Antenna
Inside Panel
Antenna
Signal Booster
Inside Panel
Antenna
Signal Booster
Understanding the Signal Booster Lights and
Troubleshooting
During installation mode the Signal Booster is resetting itself very quickly
to aid the installer. The Signal Booster is equipped with two indicator
lights, one for the 800 MHz band and the other for the 1900 MHz band.
For the first 15 minutes that the Signal Booster is plugged in, it is for a
test and alignment period. During this time, both lights will do one of the
following 4 things:
Note: If after the initial 15 minutes you are not done with the installation, the Signal Booster can be reset and enter installation mode again by disconnecting and reconnecting the power supply from the Signal Booster.
1. Blinking Green
If the Signal Booster is blinking green, the Signal Booster is operating
properly. If you are happy with the coverage area in your building, then
you are done. Blinking will stop after the 15 minute installation period.
2. Blinking Orange
Note: For AG Pro Installer see additional instructions on page 12.
If either of the two lights on the Signal Booster are blinking orange
the Signal Booster is experiencing receiver overload. The Signal
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
10
Booster has protection shut off circuits to prevent the disruption of cell
towers. If one or both lights are blinking orange, this indicates that the
Signal Booster has shut down due to close proximity to a cell tower.
First, turn down the gain control on the band that is blinking until you
get a blinking green light. The Signal Booster is now working with
reduced gain. If the gain is not adequate for good coverage, you will
need to turn the gain to maximum and then turn the Outside Antenna
away from the cell tower until the light turns to blinking green. If the
Signal Booster will not respond turn the gain down 5 dB and move
the Outside Antenna. Continue to adjust the gain and the antenna
position until the light turns blinking green. Contact Wilson Electronics
Technical Support Team for assistance: 866-294-1660.
3. Solid Red
A. A red light indicates that the booster has shut down to prevent an
oscillation, most likely caused by the Inside and Outside Antennas
being physically too close to each other. Without this patented
protection, oscillations could be transmitted to the cell tower,
blocking calls to and from the cell tower. Oscillation occurs just like
in an audio system when you put a microphone next to a speaker
and get a big squeal. When the Inside Antenna is too close to the
Outside Antenna the same type of oscillation occurs. If the booster
has a red light, the following procedure needs to be done for each
affected band.
B. Either there is a problem with the Inside and Outside Antennas
being too close together or there is a loose or bad cable (or
possibly a defective booster). First, check the booster by
unplugging the power cord, then removing the coax cables from
the two connectors of the booster. Adjust the Downlink (DL) Gain
to minimum and plug the booster back in. You should now have a
green light, if not, call Wilson Electronics Technical Support. Next,
unplug the booster, reconnect the coax cables to the booster and
tighten all connections, and plug the booster back in.
C. Increase the DL Gain until you get a red light (for example, it may
be at 50 dB for the red light). This indicates that an oscillation
occurs at gains 50 dB and higher. Separating the antennas is
very important to get the necessary gain* for the system to give
maximum coverage and a green light. Lowering gain decreases
your coverage area. The Outside Antenna, if directional, needs
to be pointed at the cell tower with its back to the Inside Antenna.
The Inside Antenna needs to have its back facing the back of the
Outside Antenna. Without proper orientation of the antennas, you
will not be able to get maximum gain from the booster.
11
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
*Note: If the antennas cannot be sufficiently separated, the booster will have to operate with reduced performance by decreasing the Downlink Gain until a green light is obtained.
4. SOLID Green
The indicator lights on the Signal Booster will be a solid green after
the first 15 minute installation period, if the unit is powered up and
working properly.
Additional Instructions for the AG Pro Installer™
with separate uplink and downlink gain controls
This Signal Booster is supplied with
separate uplink and downlink gain
controls. Note: All gain controls
should be set to maximum. If you
have green lights, the installation is
complete.
If one or more lights are blinking
orange, the Signal Booster is
experiencing receiver overload.
Reduce the uplink (UL) gain control,
without reducing the downlink (DL)
gain to eliminate the overload. This
configuration will eliminate cell tower
interference (overload) without
reducing coverage in the building.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
12
Warnings and Recommendations
Warning:
The Directional Antenna must always be located so the back or
side points to the Inside Antenna. Never point the front of the
Outside Antenna toward the Inside Antenna – this is to prevent
oscillation.
Warning:
Connecting the Signal Booster directly to the cell phone with use of
an adapter will damage the cell phone.
Warning:
Use only the power supply provided. Use of a non-Wilson
Electronics product may damage your equipment.
Warning:
RF Safety: FCC regulations require that any fixed Outside
Antenna used with this Signal Booster may not have gain (less
cable loss) that exceeds 15 dBi and must be located at least 30
inches from all people. Inside Antennas must not exceed 7 dBi
gain (less cable loss) in the 800 MHz band or 10 dBi gain (less
cable loss) in the 1900 MHz band and must be located at least
15 inches from all people.
Warning:
Verify that both the Outside Antenna and the Inside Antenna are
connected to the Signal Booster before powering up the Signal
Booster.
Recommendation: Lightning Surge Protection is recommended
for all in-building installations.
About Wilson Electronics
Wilson Electronics, Inc. has been a leader in the wireless communications industry
for over 40 years. The company designs and manufactures Signal Boosters,
antennas and related components that significantly improve cellular phone signal
reception and transmission in a wide variety of applications, both mobile (marine,
RV, vehicles) and in-building (home, office, M2M).
With extensive experience in antenna and Signal Booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically
insulated RF enclosure and cell tower simulators for compliance testing.
Wilson Electronics Signal Boosters feature patented Smart Technology ™ that
enables them to automatically adjust their power based on cell tower requirements.
By detecting and preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ Signal Boosters improve network cell
phone areas without compromising carrier systems.
All products are engineered and assembled in the company’s 55,000-square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50
states as well as in countries around the world.
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day
money-back guarantee. If for any reason the performance of any product is not
acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
1-Year Warranty
Wilson Electronics Signal Boosters are warranted for one (1) year against
defects in workmanship and/or materials. Warranty cases may be resolved by
returning the product directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the
consumer’s expense, with a dated proof of purchase and a Returned Material
Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics
will pay for delivery of the repaired or replaced product back to the original
consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson
Electronics to have been subjected to misuse, abuse, neglect, or mishandling
that alters or damages physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating
will void your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
This device complies with Part 15 of FCC rules. The transaction is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by Wilson Electronics could
void the authority to operate this equipment.
Disclaimer : The information provided by Wilson Electronics, Inc. is
believed to be complete and accurate. However, no responsibility is assumed
by Wilson Electronics, Inc. for any business or personal losses arising from its
use, or for any infringements of patents or other rights of third parties that may
result from its use.
Copyright © 2012 Wilson Electronics, Inc. All rights reserved.
One or more of the following U.S. Patent numbers may apply to the Signal Booster in this
product – D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186;
7,783,318; 7,684,838; 12,714,994.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
14
AG Pro 75™, AG Pro 70™, AG Pro Installer™, AG SOHO 60™ & AG SOHO 65™ Specifications
AG Pro 75 &
AG Pro Installer
Specifications
AG Pro 70
Specifications
Antenna connectors
N-Female
Antenna impedance
50 ohms
IC: 4726A-271265
FCC ID: PWO271265
AG SOHO 65
Specifications
AG SOHO 60
Specifications
F-Female
N-Female
FME-Male
75 ohms
50 ohms
50 ohms
Model Number
271265
Dimensions
5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm)
Weight
1.27 lbs (0.544 kg)
Frequency
1
824-894 MHz / 1850-1990 MHz
Passband Gain (nominal)
800 MHz * 1900 MHz
2
70 dB Typical,
75 dB Maximum
65 dB Typical,
70 dB Maximum
60 dB Typical,
65 dB Maximum
55 dB Typical
60 dB Typical
20 dB Bandwidth (nominal)
800 MHz
45 MHz
1900 MHz
88 MHz
Power Output
800 MHz
1900 MHz
Power output for single cell phone (uplink)
30.8 dBm
30.5 dBm
Power output for single received channel (downlink)
26.0 dBm
25.2 dBm
Power output for multiple transmitted channels
(uplink)
3
The maximum power is reduced
by the number of channels:
Maximum Power
Number of channels
800 MHz
1900 MHz
2
24.0 dBm
21.3 dBm
3
20.5 dBm
17.8 dBm
4
18.0 dBm
15.3 dBm
5
16.0 dBm
13.3 dBm
6
14.5 dBm
11.8 dBm
Power output for multiple received channels
(downlink)
4
The maximum power is reduced
by the number of channels:
Noise Figure (typical downlink/uplink)
Isolation
Power Requirements
Maximum Power
Number of channels
800 MHz
1900 MHz
2
24.8 dBm
23.7 dBm
3
21.3 dBm
20.2 dBm
4
18.8 dBm
17.7 dBm
5
16.8 dBm
15.7 dBm
6
15.3 dBm
14.2 dBm
3.5 dB nominal / 6 dB nominal
> 90 dB
110-240 V AC, 50-60 Hz, 8 W
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband
amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating
would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power
reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
AIG #110769_Rev09_03.16.12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement