NordicTrack 25044 Owner's manual

NordicTrack 25044 Owner's manual
www.nordictrack.com
Model No. 831.25044.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
ACTIVATE YOUR
WARRANTY
To register your product and
activate your warranty today, go
to www.nordictrackservice.com/
registration.
CUSTOMER CARE
For service at any time, go to
www.nordictrackservice.com.
Or call 1-800-TO-BE-FIT
(1-800-862-3348)
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
USER’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO USE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
MAINTENANCE AND TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
EXERCISE GUIDELINES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call
the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decals may not be shown at actual size.
305284
IFIT is a registered trademark of ICON Health & Fitness, Inc. App store is a trademark of Apple Inc., registered
in the U.S. and other countries. Android and Google Play are trademarks of Google Inc. The BLUETOOTH® word
mark and logos are registered trademarks of Bluetooth SIG, Inc. and are used under license. IOS is a trademark
or registered trademark of Cisco in the U.S. and other countries and is used under license.
NORDICTRACK is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
all important precautions and instructions in this manual and all warnings on your treadmill before
using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12.Plug the power cord into a surge suppressor
(not included), and plug the surge suppressor into an appropriate outlet (see page 19).
To avoid overloading the circuit, do not plug
other electrical devices, except for low-power
devices such as cell phone chargers, into
the surge suppressor or into an outlet on the
same circuit.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons
with pre-existing health problems.
3. Use the treadmill only as described in this
manual.
13.Use only a surge suppressor that meets all of
the specifications described on page 19. To
purchase a surge suppressor, see your local
NORDICTRACK dealer, call the telephone
number on the front cover of this manual, or
see your local electronics store.
4. The treadmill is intended for home use only.
Do not use the treadmill in any commercial,
rental, or institutional setting.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14.Failure to use a properly functioning surge
suppressor could result in damage to the
control system of the treadmill. If the control
system is damaged, the walking belt may
slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
6. Place the treadmill on a level surface, with
at least 8 ft. (2.4 m) of clearance behind it
and 2 ft. (0.6 m) on each side. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
15.Keep the power cord and the surge suppressor away from heated surfaces.
16.Never move the walking belt while the power
is turned off. Do not operate the treadmill
if the power cord or plug is damaged, or if
the treadmill is not working properly. (See
MAINTENANCE AND TROUBLESHOOTING
on page 28 if the treadmill is not working
properly.)
7. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
8. Keep children under age 12 and pets away
from the treadmill at all times.
9. The treadmill should be used only by persons weighing 350 lbs. (159 kg) or less.
17.Read, understand, and test the emergency
stop procedure before using the treadmill
(see HOW TO TURN ON THE POWER on
page 21). Always wear the clip while using the
treadmill.
10.Never allow more than one person on the
treadmill at a time.
11.Wear appropriate exercise clothes while
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
18.Always stand on the foot rails when starting
or stopping the walking belt. Always hold the
handrails while using the treadmill.
19.When a person is walking on the treadmill,
the noise level of the treadmill will increase.
3
20.Keep fingers, hair, and clothing away from
the moving walking belt.
26.Never insert any object into any opening on
the treadmill.
21.The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
27.Inspect and properly tighten all parts each
time the treadmill is used.
28.
22.The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
23.Never leave the treadmill unattended while
it is running. Always remove the key, press
the power switch into the off position (see
the drawing on page 7 for the location of the
power switch), and unplug the power cord
when the treadmill is not in use.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
29.Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.
24.Do not attempt to move the treadmill until it
is properly assembled. (See ASSEMBLY on
page 9, and HOW TO FOLD AND MOVE THE
TREADMILL on page 27.) You must be able
to safely lift 45 lbs. (20 kg) to raise, lower, or
move the treadmill.
30.IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter
in the console must be at least 8 in. (20 cm)
from all persons and must not be near or
connected to any other antenna or transmitter. The treadmill console contains FCC ID
OMCIABR12.
25.When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
SAVE THESE INSTRUCTIONS
4
5
STANDARD SERVICE PLANS
all
6
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
NORDICTRACK® C 950I treadmill. The C 950I treadmill offers an impressive selection of features designed
to make your workouts at home more effective and
enjoyable. And when you’re not exercising, the unique
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
reading this manual, please see the front cover of this
manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after
Tablet Holder
Length: 6 ft. 6 in. (198 cm)
Width: 3 ft. (91 cm)
Console
Tray
Heart Rate Monitor
Handrail
Upright
Key/Clip
Power Switch
Walking Belt
Foot Rail
Power Cord
Adjustable
Platform Cushions
Idler Roller
Adjustment Screws
7
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see whether it is
preattached. Extra parts may be included.
#10 Star
Washer (5)–4
#8 x 1/2" Silver
Screw (10)–1
#8 x 5/8" Screw
(100)–4
1/4" Star
Washer (8)–4
#8 x 1/2"
Screw (1)–8
5/16" Star
Washer (11)–10
#8 x 3/4" Truss
Head Screw (14)–8
3/8" x 1 1/4"
Screw (63)–2
3/8" Star
Washer (13)–8
#10 x 3/4" Screw
(9)–4
#8 x 1" Pan Head
Screw (98)–2
3/8" x 1 3/4" Screw (62)–2
5/16" x 2 1/2" Screw (28)–4
3/8" x 2 1/4" Screw (7)–4
8
ASSEMBLY
• Assembly requires two persons.
• To identify small parts, see page 8.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Assembly requires the following tools:
the included hex key
one adjustable wrench
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
one Phillips screwdriver
To avoid damaging parts, do not use power tools.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
1.
Go to www.nordictrackservice.com/
registration on your computer and register
your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
1
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
9
2. Make sure that the power cord is unplugged. Next, remove the tie securing the Upright Wire
(81) to the front of the Base (94).
Identify the Right Upright (90). Have a second
person hold the Right Upright near the Base (94).
See the inset drawing. Tie the wire tie (A) in the
Right Upright (90) securely around the end of the
Upright Wire (81). Then, insert the Upright Wire
into the lower end of the Right Upright as you
pull the other end of the wire tie out of the Right
Upright.
2
A
81
81
90
A
90
94
3. Lay the Right Upright (90) near the Base (94).
Press the Grommet (77) into the square hole (B)
in the Right Upright. Make sure not to pinch
the ground wire (C).
Next, remove and discard the indicated screw (D).
Then, attach the ground wire to the Right Upright
(90) with a #8 x 1/2" Silver Screw (10).
3
10
94
90
77
B
10
D
C
4. Hold the Right Upright (90) against the Base
(94). Make sure not to pinch the Upright Wire
(81).
Next, hold a Wheel (25) inside the Base (94),
and insert a 3/8" x 1 3/4" Screw (62) with a 3/8"
Star Washer (13) through the Wheel as shown;
do not fully tighten the Screw yet.
Next, insert two 3/8" x 2 1/4" Screws (7) with
two 3/8" Star Washers (13) and a 3/8" x 1 1/4"
Screw (63) with a 3/8" Star Washer into the
bracket at the bottom of the Right Upright (90),
and partially tighten the three Screws into the
Base (94); do not fully tighten the Screws yet.
Attach the Left Upright (not shown) in the
same way. Note: There are no wires on the left
side.
4
7
13
81
62
94
13
63
5.
Remove and save the four indicated 5/16"
x 3/4" Screws (4) from the Left and Right
Uprights (89, 90).
13
90
25
5
4
Identify the Left and Right Base Covers (82, 83).
Slide the Left Base Cover onto the Left Upright
(89), and slide the Right Base Cover onto the
Right Upright (90). Do not press the Base
Covers into place yet.
89
82
4
90
83
11
6. Attach a Handrail (86) to the Right Upright (90)
with two 5/16" x 2 1/2" Screws (28) and two
5/16" Star Washers (11) in the location shown;
do not fully tighten the Screws yet. Make
sure not to pinch the Upright Wire (81), and
make sure that the wire is on the side of the
Upright as shown.
6
28
11
86
E
Attach the other Handrail (86) to the Left
Upright (89) in the same way. Note: There are
no wires on the left side.
28
89
Then, remove and discard the indicated screws
(E).
11
E
90
86
81
7.IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do
not overtighten the #10 x 3/4" Screws (9).
7
9 28
5
Orient the Pulse Crossbar (93) as shown. Attach
the Pulse Crossbar to the Handrails (86) with two
#10 x 3/4" Screws (9) and two #10 Star Washers
(5); start all four Screws, and then tighten
them.
Next, firmly tighten the four 5/16" x 2 1/2"
Screws (28).
Then, remove the wire tie (A) from the Upright
Wire (81).
86
9
5
93
81
A
12
28
86
8.Set the console assembly (F) face down on a
soft surface to avoid scratching the console
assembly. Remove and save the four 1/4" x
1/2" Screws (34).
8
34
F
34
9.Hold the console assembly (F) near the Pulse
Crossbar (93).
See the inset drawing. Connect the pulse wires
(G, H). The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF YOU DO NOT
CONNECT THE CONNECTORS PROPERLY,
THE CONSOLE MAY BECOME DAMAGED
WHEN YOU TURN ON THE POWER.
Next, set the console assembly (F) on the brackets on the Handrails (86); do not pinch any
wires.
9
F
86
8
Attach the console assembly (F) with the four
1/4" x 1/2" Screws (34) that you removed in step
8 and four 1/4" Star Washers (8); do not fully
tighten the Screws yet.
G
93
86
H
8
34
34
G
H
13
10. Insert the Upright Wire (81) through the two
indicated looped ties (I) on the console assembly
(F).
10
See the inset drawing. Connect the Upright
Wire (81) to the console wire (J). The connectors should slide together easily and snap
into place. If they do not, turn one connector
and try again. IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER. Then, remove the wire tie
from the Upright Wire.
F
J
I
I
11.Tighten two #8 x 1" Pan Head Screws (98) into
the bottom of the console assembly (F) in the
location shown.
81
11
F
98
14
12.Identify the Right and Left Trays (27, 36).
12
27
Attach the Trays (27, 36) to the Console Base
(64) with eight #8 x 1/2" Screws (1); do not
overtighten the Screws.
36
64
1
1
13.Carefully slide the Upright Crossbar (41)
between the Left and Right Uprights (89, 90).
Attach the Upright Crossbar with the four 5/16"
x 3/4" Screws (4) that you removed in step 5
and four 5/16" Star Washers (11); start all four
Screws, and then tighten them.
13
11 4
90
15
41
4
11
89
14.Identify the Right Handrail Cover (85). Set the
Right Handrail Cover on the right Handrail (86).
Start two #8 x 3/4" Truss Head Screws (14) into
the bottom of the Handrail Cover; do not fully
tighten the Screws.
14
79
Next, slide the Right Handrail Cover (85) forward until it rests against the console assembly
(F). Then, tighten the two #8 x 3/4" Truss Head
Screws (14); do not over tighten the Truss
Head Screws.
Then, attach the Right Bottom Handrail Cover
(88) with two 8 x 3/4" Truss Head Screws (14).
Attach the Left Handrail Cover (79) and the
Left Bottom Handrail Cover (87) in the same
way.
86
14
87
14
F
85
14
88
15.Note: If the treadmill is assembled on a
smooth surface, it may roll forward during
this step.
14
15
Raise the Frame (56) to the upright position.
Have a second person hold the Frame until
step 17 is completed.
L
38
K
L
11
Remove the two 5/16" x 3/4" Screws (4) from the
Latch Crossbar (38).
4
Orient the Latch Crossbar (38) as shown. Make
sure that the “This side toward belt” sticker
(K) is facing the treadmill. Attach the Latch
Crossbar to the brackets (L) on the Frame (56)
with the two 5/16" x 3/4" Screws (4) that you just
removed and two 5/16" Star Washers (11).
11
56
16
4
86
16.Remove the 5/16" Nut (12) and the 5/16" x 1 3/4"
Bolt (6) from the bracket on the Base (94).
Next, orient the Storage Latch (53) as shown.
Attach the lower end of the Storage Latch (53)
to the bracket on the Base (94) with the 5/16" x
1 3/4" Bolt (6) and the 5/16" Nut (12).
16
M
53
Then, raise the Storage Latch (53) to a vertical
position, and remove the tie (M).
12
17.Remove the 5/16" Nut (12) and the 5/16" x 2 1/4"
Bolt (3) from the bracket on the Latch Crossbar
(38).
94
6
17
12 N
Align the upper end of the Storage Latch (53)
with the bracket on the Latch Crossbar (38),
and insert the 5/16" x 2 1/4" Bolt (3) through the
bracket and the Storage Latch. This will push
a spacer (N) out of the other end; discard the
spacer.
56
Next, tighten the 5/16" Nut (12) onto the 5/16" x
2 1/4" Bolt (3); do not overtighten the Nut; the
Storage Latch (53) must be able to pivot.
Then, lower the Frame (56) (see HOW TO
LOWER THE TREADMILL FOR USE on page
27).
17
38
3
53
18.Firmly tighten the four 3/8" x 2 1/4" Screws
(7), the two 3/8" x 1 3/4" Screws (62), and the
two 3/8" x 1 1/4" Screws (63). Do not overtighten the Screws.
18
82
Set the Left Inner Base Cover (113) onto the
lower end of the Left Upright (89). Then, slide
the Left Base Cover (82) downward and press it
onto the Left Inner Base Cover.
89
90
113
63
Next, set the Right Inner Base Cover (114) onto
the lower end of the Right Upright (90). Then,
slide the Right Base Cover (83) downward and
press it onto the Right Inner Base Cover.
83
7
62
114
63
19.Press the two tabs (not shown) on the Tablet
Holder (103) into the slots (O) in the console
assembly (F).
7
19
103
Then, attach the Tablet Holder (103) to the
console assembly (F) with four #8" x 5/8"
Machine Screws (100). Tip: Start the two upper
Machine Screws first, and then start the two
lower Machine Screws. Do not overtighten
the Machine Screws.
62
Start First
100
100
O
F
IMPORTANT: The Tablet Holder (103) is
designed for use with most full-size tablets.
Do not place any other electronic device or
object in the Tablet Holder.
20.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To
avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex key in a secure
place; the hex key is used to adjust the walking belt (see pages 29 and 30). Note: Extra hardware may be
included.
18
HOW TO USE THE TREADMILL
HOW TO CONNECT THE POWER CORD
nominal 120-volt circuit capable of carrying 15 or
more amps. To avoid overloading the circuit, do
not plug other electrical devices, except for lowpower devices such as cell phone chargers, into
the surge suppressor or into an outlet on the same
circuit. IMPORTANT: If the treadmill is connected to
an AFCI-equipped outlet and your circuit breaker
trips repeatedly when the treadmill is used, see the
front cover of this manual to purchase an arc filter.
Use a Surge Suppressor
Your treadmill, like other electronic equipment, can be
damaged by sudden voltage changes in your home’s
power. Voltage surges, spikes, and noise interference can result from weather conditions or from other
appliances being turned on or off. To decrease the
risk of damaging the treadmill, always use a surge
suppressor with the treadmill. To purchase a surge
suppressor, see precaution 13 on page 3.
1
Grounded Outlet
Grounding Pin
Use only a surge suppressor that is UL 1449 listed as a
transient voltage surge suppressor (TVSS). The surge
suppressor must have a UL suppressed voltage rating
of 400 volts or less and a minimum surge dissipation of
450 joules. The surge suppressor must also be electrically rated for 120 volts AC and 15 amps. There must
be a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill
and serious injury to users.
Grounding Pin
Surge
Suppressor
Plug in the Power Cord
The treadmill must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. The treadmill power cord has a plug with a
grounding pin (see drawing 1 on this page).
A temporary
adapter may
be used to
connect the
surge suppressor to a 2-pole
receptacle
if a properly
grounded outlet is not
available.
DANGER: Improper connection
of the power cord increases the risk of electric shock. Do not modify the plug—if it will
not fit an outlet, have a proper outlet installed
by a qualified electrician. If you are unsure
whether the treadmill is properly grounded,
contact a qualified electrician.
2
2-pole Receptacle
Adapter
Lug
Metal
Screw
The lug or wire extending from the adapter must
be connected with a metal screw to a permanent
ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not
grounded. Before using an adapter, contact a qualified electrician to determine whether the outlet box
cover is grounded. The temporary adapter should
be used only until a properly grounded outlet can
be installed by a qualified electrician.
Plug the power cord into a surge suppressor, and plug
the surge suppressor into an appropriate outlet that is
properly installed and grounded in accordance with all
local codes and ordinances. The outlet must be on a
19
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
To turn on the power, see page 21. To use the manual mode, see page 21. To use an onboard workout,
see page 23. To use a custom-focus weight loss
workout, see page 24. To connect your smart device to the console, see page 25. To connect your
heart rate monitor to the console, see page 25. To
use the sound system, see page 26. To use the settings mode, see page 26.
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable. When you use the manual mode,
you can change the speed and incline of the treadmill
with the touch of a button. As you exercise, the console
will display instant exercise feedback. You can even
measure your heart rate using the handgrip heart rate
monitor or a compatible heart rate monitor. See page
25 for information about purchasing an optional
chest heart rate monitor.
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of measurement is selected, see THE SETTINGS MODE on
page 26. For simplicity, all instructions in this section
refer to miles.
In addition, the console features a selection of onboard workouts. Each workout automatically controls
the speed and incline of the treadmill as it guides you
through an effective exercise session.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use
the treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 30).
You can also connect your smart device to the console
and use an iFit® app to record and track your workout
information.
You can even listen to your favorite workout music or
audio books with the console’s sound system while you
exercise.
ETS899215
20
15
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before you turn on the power. If you do
not do this, you may damage the console displays
or other electrical components.
1.Insert the key into the console.
Plug in the power cord (see
page 19). Next, locate the
power switch on the treadmill frame near the power
cord. Press the power
switch into the reset
position.
See HOW TO TURN ON THE POWER at the left.
2.Select the manual mode.
Reset
Press the Manual button to select the manual
mode.
3. Enter your weight.
Press the Enter Wt increase or decrease buttons to
enter your weight. This information will improve the
accuracy of the Calorie Burn Rate bar.
Next, stand on the foot
rails of the treadmill.
Find the clip attached
to the key and slide
the clip onto the waistClip
band of your clothes.
Key
Then, insert the key
into the console. After
a moment, the displays
will light.
IMPORTANT: In an emergency, the key can be
pulled from the console, causing the walking belt
to slow to a stop. Test the clip by carefully taking
a few steps backward; if the key is not pulled from
the console, adjust the position of the clip.
4. Start the walking belt.
To start the walking belt, press the Start button or
one of the Quick Speed buttons.
If you press the Start button, the walking belt will
begin to move at 1 mph. As you exercise, change
the speed of the walking belt as desired by pressing the Speed increase and decrease buttons.
Each time you press one of the buttons, the speed
setting will change by 0.1 mph; if you hold down
the button, the speed setting will change in increments of 0.5 mph. Note: After you press the button,
it may take a moment for the walking belt to reach
the selected speed setting.
IMPORTANT: Before you use the treadmill, take
the following steps to ensure that the console
shows the correct incline level of the treadmill:
First, press the Incline increase button once. Next,
press either the Incline decrease button or the lowest Quick Incline button to set the treadmill to its
lowest setting. When the frame stops moving, the
treadmill is ready for use.
If you press one of the Quick Speed buttons, the
walking belt will gradually change speed until it
reaches the selected speed setting. To select a
speed setting that includes a decimal—such as 3.5
mph—press two numbered buttons in succession.
For example, to select a speed setting of 3.5 mph,
press the 3 button and then immediately press the
5 button. Note: This will not function if the console
is set to metric units.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Start button.
21
5. Change the incline of the treadmill as desired.
To reset the displays, press the Stop button repeatedly, or remove the key and then reinsert the key.
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the Quick Incline buttons. Each time you press one
of the buttons, the treadmill will gradually adjust to
the selected incline setting.
7. Measure your heart rate if desired.
You can measure your heart rate using either the
handgrip heart rate monitor or a compatible heart
rate monitor. For information about purchasing
an optional chest heart rate monitor, see page
25.
6.Follow your progress with the displays.
As you walk or run on the treadmill, the display can
show the following workout information:
• The approximate number of calories you have
burned
• The incline level of the treadmill
• The distance that you have walked or run
• The elapsed time
• Your heart rate (see step 7)
The console is compatible with all BLUETOOTH®
Smart heart rate monitors. To connect your heart
rate monitor to the console, see page 25.
Note: If you use both heart rate monitors at the
same time, the BLUETOOTH Smart heart rate
monitor will have priority.
Before using
the handgrip
heart rate monitor, remove the
sheets of plastic
from the metal
contacts on
the pulse bar.
In addition,
make sure that
your hands are
clean.
•
Your pace
•
The approximate number of calories you are
burning per hour
• The speed of the walking belt
Press the Display button until the desired information is shown in the displays.
Contacts
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on
the metal contacts; avoid moving your hands.
When your pulse is detected, your heart rate will be
shown. For the most accurate heart rate reading, continue to hold the contacts for about 15
seconds.
As you exercise, the Calorie Burn Rate bar will
indicate the approximate intensity level of your
exercise. To adjust your calorie burn rate, press the
Burn Rate increase or decrease button. The speed
and/or incline settings of the treadmill will automatically increase or decrease to reach the desired
calorie burn rate.
22
8. Turn on the fan if desired.
HOW TO USE AN ONBOARD WORKOUT
The fan features multiple speed settings and an
auto mode. When the auto mode is selected,
the speed of the fan will automatically increase
and decrease as the speed of the walking belt
increases and decreases.
Press the fan buttons repeatedly to select a fan speed or
the auto mode, or to turn off
the fan.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 21.
2. Enter your weight.
See step 3 on page 21.
3. Select an onboard workout.
9.When you are finished exercising, remove the
key from the console.
To select an onboard workout, press the Incline
button, the Intensity button, or the Speed button
repeatedly until the desired workout appears in the
display.
When you select an onboard workout, the display
will show the duration of the workout.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to zero. The
incline must be at zero orETS899215
you may damage the
treadmill when you fold it to the storage position. Next, remove the key from the console and
put it in a secure place.
4. Start the workout.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmill’s electrical components may
wear prematurely.
ress the Start button. A moment after you press
P
the button, the treadmill will automatically adjust to
the first speed and incline settings of the workout.
Hold the handrails and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting and/
or incline setting may be programmed for consecutive segments.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually override the setting by pressing the Speed or
Incline buttons; however, when the next segment
of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
To stop the workout at any time, press the Stop
button. To resume the workout, press the Start button. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
23
5. Follow your progress with the displays.
HOW TO USE A CUSTOM-FOCUS WEIGHT LOSS
WORKOUT
See step 6 on page 22. If you select an onboard
workout, the display will show the time remaining
instead of the elapsed time.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 21.
6. Measure your heart rate if desired.
2. Enter your weight.
See step 7 on page 22.
7. Turn on the fan if desired.
3. Set a calories or time goal.
See step 8 on page 23.
Press the desired Workout Time or Calorie Goal
button.
8. W
hen you are finished exercising, remove the
key from the console.
See step 3 on page 21.
4. Start the workout.
See step 9 on page 23.
Press the Start button to start the workout. A
moment after you press the button, the walking belt
will begin to move. Hold the handrails and begin
walking.
The workout will function in the same way as the
manual mode (see pages 21 to 23).
The workout will continue until you reach the goal
that you set. The walking belt will then slow to a
stop.
Note: The calorie goal is an estimate of the
number of calories that you will burn during the
workout. The actual number of calories that you
burn will depend on various factors such as
your weight.
5. Follow your progress with the displays.
See step 6 on page 22. The display will show the
time remaining instad of the elapsed time.
6. Measure your heart rate if desired.
See step 7 on page 22.
7. Turn on the fan if desired.
See step 8 on page 23.
8.When you are finished exercising, remove the
key from the console.
See step 9 on page 23.
24
HOW TO CONNECT YOUR SMART DEVICE TO THE
CONSOLE
THE OPTIONAL CHEST HEART RATE MONITOR
Whether your
goal is to
burn fat or to
strengthen your
cardiovascular
system, the key
to achieving the
best results is
to maintain the
proper heart
rate during your
workouts. The optional chest heart rate monitor will
enable you to continuously monitor your heart rate
while you exercise, helping you to reach your personal
fitness goals. To purchase a chest heart rate monitor, please see the front cover of this manual.
The console supports BLUETOOTH connections to
smart devices via the iFit app and to compatible heart
rate monitors. Note: Other BLUETOOTH connections
are not supported.
1.Download and install the iFit app on your smart
device.
On your IOS® or AndroidTM smart device, open the
App StoreSM or the Google PlayTM store, search for
the free iFit app, and then install the app on your
smart device. Make sure that the BLE option is
enabled on your smart device.
Then, open the iFit app and follow the instructions
to set up an iFit account and customize settings.
Note: The console is compatible with all BLUETOOTH
Smart heart rate monitors.
2. Connect your smart device to the console.
Follow the instructions in the iFit app to connect
your smart device to the console.
HOW TO CONNECT YOUR HEART RATE MONITOR
TO THE CONSOLE
When a connection is established, the LED on the
console will flash blue. Press the Bluetooth button
on the console to confirm the connection; the LED
on the console will then turn solid blue.
The console is compatible with all BLUETOOTH Smart
heart rate monitors.
To connect your BLUETOOTH Smart heart rate monitor to the console, press the Bluetooth button on the
console. When a connection is established, the LED on
the console will flash twice. Note: This may take up to
15 seconds.
3.Record and track your workout information.
Follow the instructions in the iFit app to record and
track your workout information.
4.Diconnect your smart device from the console
if desired.
Note: If there is more than one compatible heart rate
monitor near the console, the console will connect to
the heart rate monitor with the strongest signal.
To disconnect your smart device from the console,
press and hold the Bluetooth button on the console
for 5 seconds; the LED on the console will turn off.
To disconnect your heart rate monitor from the console,
press and hold the Bluetooth button on the console for
5 seconds; after the LED lights, release the button.
Note: All BLUETOOTH connections between the
console and other devices (including any smart
devices, heart rate monitors, and so forth) will be
disconnected.
Note: All BLUETOOTH connections between the
console and other devices (including any smart
devices, heart rate monitors, and so forth) will be
disconnected.
25
HOW TO USE THE SOUND SYSTEM
HOW TO ADJUST THE CUSHIONING SYSTEM
To play music or audio books through the console
sound system while you exercise, plug a 3.5 mm male
to 3.5 mm male audio cable (not included) into the jack
on the console and into a jack on your MP3 player,
CD player, or other personal audio player; make sure
that the audio cable is fully plugged in. Note: To
purchase an audio cable, see your local electronics
store.
Remove the key from the console and unplug the
power cord. In order to adjust the cushions, you may
need to place the treadmill in the storage position (see
HOW TO FOLD THE TREADMILL on page 27).
For a firmer walking platform, turn a cushion to the
position shown in drawing 1; for a less firm walking
platform, turn the cushion to the position shown in
drawing 2. Adjust the other cushions in the same way.
Note: Make sure that the cushions on the left and
right sides of the treadmill are set to the same firmness level. The faster you run on the treadmill, or
the more you weigh, the firmer the walking platform should be.
Next, press the play button on
your personal audio player.
Adjust the volume level using the
volume increase and decrease
buttons on the console or the
volume control on your personal
audio player.
ETS899215
1
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat
surface instead of on the console.
2
More
firm
THE SETTINGS MODE
The console features a settings mode that keeps track
of treadmill usage information and allows you to select
a unit of measurement for the console.
To select the information mode, insert the key into the
console while holding down the Stop button. Then,
release the Stop button. Note: If a workout has been
selected, you may have to press the Stop button twice
to exit the workout before you can access the information mode. When the information mode is selected, the
following information will be shown:
An “E” for English miles or an “M” for metric kilometers
will appear in the display. Press the Speed increase or
decrease button to change the unit of measurement, if
desired.
To exit the information mode, remove the key from the
console, or press stop repeatedly.
26
Less
firm
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to zero before you fold the treadmill. Then, remove
the key and unplug the power cord. CAUTION: You
must be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the treadmill.
Before moving the treadmill, fold it as described at the
left. CAUTION: Make sure that the storage latch is
locked in the storage position. Moving the treadmill
may require two people.
Hold the handrails with both hands and carefully push
the treadmill to the desired location. CAUTION: Do not
pull on the frame, and do not move the treadmill
over an uneven surface.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
Handrail
Frame
Wheel
2.Raise the frame until the storage latch locks in the
storage position. CAUTION: Make sure that the
storage latch locks.
Wheel
HOW TO LOWER THE TREADMILL FOR USE
2
1. Push the upper end of
the frame forward, and
gently press the upper
part of the storage latch
with your foot at the same
time.
Frame
Storage
Latch
2. While pressing the storage latch with your foot,
pull the upper end of the
frame toward yourself.
3.Step back and let the
frame lower to the floor.
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
27
1
2
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE
c.Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
Regular maintenance is important for optimal performance and to reduce wear. Inspect and properly tighten
all parts each time the treadmill is used.
Regularly clean the treadmill and keep the walking
belt clean and dry. First, press the power switch into
the off position and unplug the power cord. Wipe
exterior parts of the treadmill with a damp cloth and a
small amount of mild soap. IMPORTANT: Do not spray
liquids directly onto the treadmill. To avoid damage
to the console, keep liquids away from the console.
Then, thoroughly dry the treadmill with a soft towel.
c
Tripped
Reset
SYMPTOM: The power turns off during use
a.Check the power switch (see drawing c at the left).
If the switch has tripped, wait for five minutes and
then press the switch back in.
TROUBLESHOOTING
Most treadmill problems can be solved by following
the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
b.Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
SYMPTOM: The power does not turn on
c.Remove the key from the console, and then
reinsert it.
a.Make sure that the power cord is plugged into a
surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see
page 19). Use only a surge suppressor that meets
all of the specifications described on page 19.
IMPORTANT: If the treadmill is connected to an
AFCI-equipped outlet and your circuit breaker
trips repeatedly when the treadmill is used, see
the front cover of this manual to purchase an
arc filter.
d.If the treadmill still will not run, please see the front
cover of this manual.
b.
After the power cord has been plugged in, make
sure that the key is inserted into the console.
28
SYMPTOM: The incline of the treadmill does not
change correctly
c.
Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deteriorate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
a. Hold down the Stop button and the Speed increase
button, insert the key into the console, and then
release the Stop button and the Speed increase
button. Next, press the Stop button and then
press the Incline increase or decrease button. The
treadmill will automatically rise to the maximum
incline level and then return to the minimum level.
This will recalibrate the incline system. If the incline
system does not begin calibrating, press the Stop
button again, and then press the Incline increase or
decrease button again. When the incline system is
calibrated, remove the key from the console.
d.If the walking belt still slows when walked on, see
the front cover of this manual.
SYMPTOM: The walking belt is off-center or slips
when walked on
SYMPTOM: The walking belt slows when walked on
a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn; if the walking belt has shifted to the
right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a.
Use only a surge suppressor that meets all of the
specifications described on page 19.
b.If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
a
b
2–3 in.
Idler Roller Screws
29
b. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
SYMPTOM: The tablet holder does not stay in place
a.
Rotate the tablet holder backwards. Then, tighten
the indicated screw slightly until the tablet holder
stays in place when it is rotated to the desired
position.
a
b
Screw
30
Tablet
Holder
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
31
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch­—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from your
hips. Allow your back and shoulders to relax as you reach down toward
your toes as far as possible. Hold for 15 counts, then relax. Repeat 3
times. Stretches: Hamstrings, back of knees and back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your hands
against a wall. Keep your back leg straight and your back foot flat on
the floor. Bend your front leg, lean forward and move your hips toward
the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg. To
cause further stretching of the achilles tendons, bend your back leg as
well. Stretches: Calves, achilles tendons and ankles.
3
4. Quadriceps Stretch
4
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks as
possible. Hold for 15 counts, then relax. Repeat 3 times for each leg.
Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.
5
32
NOTES
33
PART LIST
Model No. 831.25044.0 R0915A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#8 x 1/2" Screw
#8 x 3/4" Screw
5/16" x 2 1/4" Bolt
5/16" x 3/4" Screw
#10 Star Washer
5/16" x 1 3/4" Bolt
3/8" x 2 1/4" Screw
1/4" Star Washer
#10 x 3/4" Screw
#8 x 1/2" Silver Screw
5/16" Star Washer
5/16" Nut
3/8" Star Washer
#8 x 3/4" Truss Head Screw
1/4" x 2 1/2" Screw
3/8" x 1 1/2" Bolt
3/8" x 1 1/2" Wheel Bolt
Console Frame
#8 x 7/16" Screw
5/16" Motor Screw
1/4" Pin
3/8" x 1 1/4" Bolt
5/16" x 1 3/4" Shoulder Bolt
#8 Star Washer
Wheel
Cable Tie
Right Tray
5/16" x 2 1/2" Screw
3/8" x 1 3/4" Hex Head Bolt
5/16" Flat Washer
1/4" x 1 1/2" Screw
Incline Motor Spacer
3/8" Jam Nut
1/4" x 1/2" Screw
1/4" Nut
Left Tray
#8 x 5/8" Screw
Latch Crossbar
Isolator
Rear Foot
Upright Crossbar
Left Foot Rail
Warning Decal
Walking Platform
Walking Belt
Belt Guide
Right Rear Foot
Cable Tie
Drive Roller/Pulley
(Not Used)
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
(Not Used)
(Not Used)
Storage Latch
Drive Motor
Motor Belt
Frame
Left Rear Foot
Console Ground Wire
Rubber Cushion
Right Foot Rail
Idler Roller
3/8" x 1 3/4" Screw
3/8" x 1 1/4" Screw
Console Base
Motor Hood
Hood Accent
Incline Frame Spacer
Hood Clip
Incline Motor
Incline Frame
Frame Spacer
Controller
Controller Clamp
9/32" Plastic Bushing
Power Switch
Power Cord
Grommet
Belly Pan
Left Handrail Cover
Console
Upright Wire
Left Base Cover
Right Base Cover
M5 Flat Washer
Right Handrail Cover
Handrail
Left Bottom Handrail Cover
Right Bottom Handrail Cover
Left Upright
Right Upright
Caution Decal
Console Clamp
Pulse Crossbar
Base
Pulse Crossbar Cover
Key
#8 x 1" Truss Head Screw
#8 x 1" Pan Head Screw
#6 x 1/2" Screw
#8 x 5/8" Screw
19
31
1
6
4
1
4
4
4
1
10
6
8
8
3
1
2
1
4
2
2
2
4
2
4
2
1
4
1
4
2
2
6
4
13
1
8
1
6
2
1
1
1
1
1
2
1
4
1
–
34
–
–
1
1
1
1
1
1
4
1
1
2
2
1
1
1
2
5
1
1
2
1
1
2
1
1
2
1
1
1
1
1
1
8
1
2
1
1
1
1
2
2
1
1
1
1
6
2
12
4
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
#3 x 1/4" Screw
Fan Screw
Tablet Holder
Left Speaker Grill
Right Speaker Grill
Speaker
Left Speaker Cover
Right Speaker Cover
Fan
Controller Clamp
Incline Leg Bushing
Incline Leg Washer
Left Inner Base Cover
Right Inner Base Cover
#8 x 1" Tek Screw
Base Pad
#8 x 1/2" Machine Screw
User’s Manual
4
2
1
1
1
2
1
1
1
110
111
112
113
114
115
116
117
*
1
4
2
1
1
4
2
7
–
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
35
15
35
1
36
2
59
30
12
23
84
39
2
61
37
43
35
1
2
57
40
44
15
84
37
35
39
35
11
4
1
2
40
39
35
23
2
45
84
37
42
47
84
37
59
30
12
46
56
35
35
60
19
30
84
35
1
37
12
59
12
39
37
84
21
11
4
3
49
35
74
23
35
1
117
31
53
39
37
84
55
35
39
35
1
37
35
38
19
20
84
59
30
12
15
12
46
23
54
48
21
74
6
31
117
117
110
73
117
24
EXPLODED DRAWING A
Model No. 831.25044.0 R0915A
EXPLODED DRAWING B
Model No. 831.25044.0 R0915A
2
2
2
65
66
29
67
112
33
111
71
16
70
33
69
33
112
32
111
67
33
71
2
2
68
2
72
68
68
2
75
68
117
2
2
68
2
2
37
78
2
77
76
EXPLODED DRAWING C
Model No. 831.25044.0 R0915A
28
95
9
11
93
5
8
86
79
34
1
1
58
117
87
9
5
1
14
28
14
11
1
11
4
8
85
89
34
11
4
81
41
4
86
11
14
88
7
63
13
22
82
113
91
4
13
11
90
25
13
111
62
111
116
115
17
25
14
25
22
62 13
81
94
33
25
17
38
13
10
91
33
7
77
116
114
115
13
13
7
83
63
EXPLODED DRAWING D
Model No. 831.25044.0 R0915A
103
104
101 107
106
105
36
99
99
99
2
99
100
64
2
106
101
1
99
99
26
108
1
2
2
2
99
1
99
80
109
99
2
2
1
27
102
18
97
92
98
97
92
97
96
97
39
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
LIMITED WARRANTY
IMPORTANT: To protect your fitness equipment with an extended service plan, see page 6.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and drive motor are warranted for the
lifetime of the original purchaser (customer). Parts are warranted for three (3) years from the date of purchase. Labor is warranted for one (1) year from the date of purchase.
This warranty extends only to the customer. ICON’s obligation under this warranty is limited to repairing or
replacing, at ICON’s option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be preauthorized by ICON. If the product is shipped to a service center,
freight charges to and from the service center will be the customer’s responsibility. If replacement parts
are shipped while the product is under warranty, the customer will be responsible for a minimal handling
charge. For in-home service, the customer will be responsible for a minimal trip charge. This warranty
does not extend to freight damage to the product. This warranty will automatically be voided if the product
is used as a store display model, if the product is purchased or transported outside the USA, if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used, or if the
product is used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specific legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 373056 R0915A
Printed in China © 2015 ICON Health & Fitness, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement