Century 211 Modular

Century 211 Modular
CENTURY
L
E
G
E
N
D
OWNER'S MANUAL
A
R
®
Y
L
E
A
D
E
R
S
H
I
P
MODULAR 211
PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice.
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0501698
02 / 2010
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original
purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and
workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty
period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly
notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such
notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in
service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the
MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection
by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any
replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER
to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts
found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless
authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY,
EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or
any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts,
whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any
other legal theory, regardless of whether the loss resulted from any general or particular requirement which
MILLER knew or had reason to know about at the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories
or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language
shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by
such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the
purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through
changes in design or materials as it may deem desirable without being obligated to incorporate such changes
in products previously sold. This warranty is not intended to cover or include the following items, which are set
forth by way of example and not limitation:
A.Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather,
road conditions, road treatments, etc.
B.Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide
reasonable and necessary maintenance, or uses for which the equipment was not designed or intended.
C.Alterations or modifications that affect performance, operation or reliability.
D.Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps,
fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER
IMPROPER USE.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
SERIAL NUMBER
OWNER, USER AND OPERATOR:
We appreciate your choice of our towing and recovery unit for your application. Our number one priority is
user safety which is best achieved by our joint efforts. We feel that you can make a major contribution to
safety if you, as the equipment owner and operator:
1.Comply with Federal, State, and Local Regulations.
2.Read, Understand, and Follow the Instructions in this Manual.
3.Use Good, Safe Work Practices in a Common Sense Way.
4.Only have Authorized and Trained Personnel performing maintenance on the Towing and Recovery
Unit.
© 2010 MILLER INDUSTRIES TOWING EQUIPMENT INC. All rights reserved. Reproduction or use, without express permission, of editorial or
pictorial content, in any manner, is prohibited.
i
TABLE OF CONTENTS
It is assumed by the manufacturer that the Owner/Operator has a thorough knowledge of the accepted and lawful
retrieval and towing methods as dictated by his city, county or state. The manufacturer rejects any liability claim that
may result from the incorrect or unlawful application of its equipment.
Section I - PARTS
SUBFRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-2 & I-3
BODY ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4 & I-5
RECOVERY BOOM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-6 & I-7
WHEEL LIFT BOOM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-8 & I-9
CROSSBAR & OUTER CROSSTUBE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-10 & I-11
RECOVERY BOOM & WHEEL LIFT HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-12 & I-13
PUMP, VALVE & FILTER HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-14 & I-15
CONTROL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-16 & I-17
BOOM SWIVEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-18
ii
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering any component part of the Century Modular
211 that may be required when part replacement is necessary. Be certain to use only original equipment replacement
parts for warranty purposes as well as for keeping your unit in its original state and optimum operating capacities.
When ordering replacement or spare parts be sure to provide the following information to the manufacturer's Parts
Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be delivered to you in an expedient manner
without delay. Should additional information be required for repair or replacement of certain components, contact
your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve or modify their products, which may
change the specifications, models and feature availability.
I-1
Section I - PARTS (cont'd)
SUBFRAME ASSEMBLY
I-2
Section I - PARTS (cont'd)
SUBFRAME ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
PART NUMBER
0300011
0301671
0301895
0303385
0306680
0307576
0400066
0400070
0400078
0400122
0400126
0400132
0400140
0400146
0400209
0400237
0400367
0400382
0400392
0400408
0400451
0400452
0400480
0400482
0400492
0400498
0712380
0719519
0719520
0722941
0806850
0807183
0807214
0807215
0807230
0807232
0807471
0807707
0902842
0908534
0910008
9011011
9012839
9043973
9056150
805040011
BA0259
DESCRIPTION
VALVE, 4 SPOOL CONTROL
TOW SOCKET
GREASE FITTING, 1/8 NPT STRAIGHT
JUNCTION BOX
RUBBER "T" MOUNTS
LIFT CYLINDER
1/4-20 X 3/4 HHCS GR.5,ZP
1/4-20 x 1 HHCS GR5 ZP
1/4-20 x 2 HHCS GR5 ZP
3/8-16 X 1 1/4 HHCS GR.5,ZP
3/8-16 X 1 HHCS GR.5,ZP
3/8-16 X 1 1/2 HHCS GR.5,ZP
3/8-16 X 4 HHCS GR.5,ZP
3/8-16 x 2-1/4 HHCS GR.5 ZP
1/2-13 x 1-1/4 HHCS GR5 ZP
1/2-13 x 4 HHCS GR 5 ZP
1/4-20 NYLOCK HEX NUT ZP
5/16-18 NYLOCK HEX NUT ZP
3/8-16 NYLOCK HEX NUT ZP
1/2-13 NYLOCK HEX NUT ZP
1/4 FLAT WASHER ZP
1/4 HELICAL LOCK WASHER ZP
3/8 FLAT WASHER ZP
3/8 HELICAL LOCK WASHER ZP
1/2 FLAT WASHER ZP
WASHER, 1/2' ID X 2" OD X .150
"D" RING
SHIM - BOOM PIVOT ( .0747 THICK )
SHIM- BOOM PIVOT (.1196 THK)
BRACKET - JUNCTION BOX STAND
VALVE MOUNTING BRACKET WELDMENT
BOOM PIVOT PIN WELDMENT
SCOOP STORAGE WELD'T LH
SCOOP STORAGE WELD'T RH
880 SUBFRAME -NEW CONV
FRONT BODY MTG.TUBE WELD'T
REAR BODY MTG TUBE WELD'T
PIN WELDMENT
KIT - "D" RING
4-SPOOL VALVE PLATE
HYDRAULIC TANK ASSEMBLY PIPE PLUG, 1/4" SQ HD
PLUG 1" (HYDRAULIC) HEX HEAD
SCREW, 5/16"-16 X 1-1/2" FL HD SKT
RETAINING RING, 1-1/2"
VERTICAL BOOM GUIDE
PIN, 'D' RING
I-3
QTY
1
1
2
1
4
1
8
8
2
2
4
2
3
1
4
4
14
8
12
8
14
4
9
1
8
8
2
2
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
8
1
2
2
Section I - PARTS (cont'd)
BODY ASSEMBLY
I-4
Section I - PARTS (cont'd)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
BODY ASSEMBLY
PART NUMBER
0302173
0303120
0306680
0310148
0310214
0310215
0310353
0310354
0310355
0310356
0400126
0400132
0400133
0400351
0400392
0400480
0400482
0400484
0400686
0400688
0400689
0400690
0400823
0400824
0402020
0402032
0402110
0402111
0402116
0402117
0402118
0402120
0402121
0719710
0719921
0721514
0722061
0807249
0807250
0807319
0807320
0807326
0807415
0807416
9032053
804500001
806070010
945400518
945400800
GV57
DESCRIPTION
QTY
MUD FLAP
PADDLE LATCH W/GASKET
RUBBER "T" MOUNTS
BOOT - CONTROL HANDLE
LAMP, LED SIDE MARKER (AMBER)
LAMP, LED SIDE MARKER (RED)
LIGHT, AGROLUN LH STOP/TAIL
LIGHT, AGROLUN RH STOP/TAIL
LIGHT, AGROLUN LH BACK-UP
LIGHT, AGROLUN RH BACK-UP
3/8-16 X 1 HHCS GR.5,ZP
3/8-16 X 1 1/2 HHCS GR.5,ZP
3/8-16 X 3 HHCS GR.5,ZP
#8-32 HEX NUT W/ STAR WASHER, ZP
3/8-16 NYLOCK HEX NUT ZP
3/8 FLAT WASHER ZP
3/8 HELICAL LOCK WASHER ZP
3/8 X 1-3/4 X 1/8 THICK FLAT WASHER ZP
#10-24 X 1" PAN HEAD PHILLIPS
#10-24 NYLOCK HEX NUT SS
SCREW, #8-32 X 1/2" FL HD PH MACH
NUT, #8-32 HEX NYLOK
5/16-18 X 3/4 LG HHCS SS
5/16-18 X 3/4 LG HHCS SS
1/4-20 X 3/4 HHCS SS
5/16 X 1 HHCS SS
1/4 FLATWASHER 316 STAINLESS
1/4 LOCKWASHER 316 STAINLESS
5/16"-18 NC HEX NYLOK NUT SS
5/16 FLATWASHER 316SS
5/16 HELICAL LOCK WASHER SS
3/8 FLATWASHER 316 SS
3/8 LOCKWASHER 316 STAINLESS
SPLIT HARNESS PLATE
BODY / SUBFRAME MTG. PLATE TAIL LIGHT INSPECTION COVER PLATE
PLATE - 4 FUNCTION CONTROL COVER
804 CENTER COVER WELDMENT
804 CENTER COVER SUPPORT WELDMENT
LH 94" WIDE DECK MTG. ANGLE WELDMENT
RH 94" WIDE DECK MTG. ANGLE WELDMENT
FRONT DECK MTG. CROSSMEMBER WELD'T
LH C.S. BODY WELDMENT
RH C.S. BODY WELDMENT
GROMMET
MUD FLAP BACK-UP STRIP
MUD FLAP EXTENSION PLATE
WASHER PLATE
STRIKER PIN WELD'T
RUBBER GROMMET 2
2
2
8
2
4
2
2
1
1
16
6
2
8
20
24
6
5
12
12
12
12
30
2
24
16
8
24
22
40
32
2
2
4
2
2
2
1
1
1
1
1
1
1
2
2
2
2
2
2
I-5
Section I - PARTS (cont'd)
RECOVERY BOOM ASSEMBLY
I-6
Section I - PARTS (cont'd)
RECOVERY BOOM ASSEMBLY
ITEM
PART NUMBER
DESCRIPTION
1
0300113
GREASE FITTING, 1/4-28 STRAIGHT
2
0301533
TIE DOWN STRAP, 15"
3
0302919
FOLD CYLINDER
4
0306688
TIMBREN SPRING
5
0307097
HYDRAULIC MOTOR, PARKER
6
0307579
WINCH ASSEMBLY, HY-246 NARROW DRUM
7
0307965
PLUG - 1-3/4 DIA
8
0307966
PLUG - 1/2 DIA
9
0400066
1/4-20 X 3/4 HHCS GR.5,ZP
10
0400078
1/4-20 X 2 HHCS GR5 ZP
11
0400121
3/8-16NC X 3/4 HHCS GR. B
12
0400122
3/8-16 X 1 1/4 HHCS GR.5,ZP
13
0400126
3/8-16 X 1 HHCS GR.5,ZP
14
0400133
3/8-16 X 3 HHCS GR.5,ZP
15
0400196
SCREW, 1/2"-13 X 1-1/4" SKT HD
16
0400367
1/4-20 NYLOCK HEX NUT ZP
17
0400392
3/8-16 NYLOCK HEX NUT ZP
18
0400451
1/4 FLAT WASHER ZP
19
0400452
1/4 HELICAL LOCK WASHER ZP
20
0400480
3/8 FLAT WASHER ZP
21
0400482
3/8 HELICAL LOCK WASHER ZP
22
0400491
1/2 HELICAL LOCK WASHER ZP
23
0706668
SHIM, WINCH MOUNTING
24
0708519
PLATE, ACCESS COVER 25
0717069
PIN - MIDNIGHT U/L
26
0718218
PIN - FOLD (BASE)
27
0807078
MAIN OUTER BOOM WELDMENT
28
0908627
WINCH FREE-SPOOL ASSY
29
9055275
SNAP RING, 2-3/4" EXTERNAL
30
9056150
RETAINING RING, 1-1/2"
31
805180000
SHEAVE HOUSING ASSEMBLY
32
880401500
PIN BOOM LIFT CYLINDER UPPER
I-7
QTY
2
1
1
1
1
1
1
1
2
1
1
6
1
1
2
1
1
2
2
1
8
2
2
1
1
1
1
1
1
2
1
1
Section I - PARTS (cont'd)
WHEEL LIFT BOOM ASSEMBLY
I-8
Section I - PARTS (cont'd)
WHEEL LIFT BOOM ASSEMBLY
ITEM
PART NUMBER
3012-794003
3012-794004
0300113
0301397
0301825
0306942
0400121
0400122
0400139
0400152
0400154
0400217
0400398
0400482
0400491
0400492
0718216
0718528
0718949
0806842
0807027
0807082
9056150
807500001
896040002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
DESCRIPTION
BAR - SPACER
PLATE - UL PAD CAGE
GREASE FITTING, 1/4-28 STRAIGHT
GREASE FITTING, 90 DEG
CYLINDER HYDRAULIC EXTEND
CAST BRONZE BEARING- SLEEVE 1 1/2"
3/8-16NC X 3/4 HHCS GR. B
3/8-16 X 1 1/4 HHCS GR.5,ZP
SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
SCREW, 3/8"-16 X 5/8" SKT HD SUNK
3/8-16 X 1/2 HHCS GR.5,ZP
1/2-20 X 1.00 HHCS GR8 ZP
3/8-16 NYLOCK HALF-NUT ZP
3/8 HELICAL LOCK WASHER ZP
1/2 HELICAL LOCK WASHER ZP
1/2 FLAT WASHER ZP
SHAFT- INNER TUBE CYLINDER
ANGLE - BOOM COVER
PLATE - XBAR POSITIONING
PIN WELDMENT
OUTER W/L BOOM WELDMENT
INNER UNDERLIFT BOOM WELDMENT
RETAINING RING, 1-1/2"
PIN - EXTEND
NYLATRON PAD
I-9
QTY
1
1
4
2
1
2
4
2
1
1
1
4
1
6
4
4
1
1
2
1
1
1
1
1
4
Section I - PARTS (cont'd)
CROSSBAR & OUTER CROSSTUBE ASSEMBLY
I-10
Section I - PARTS (cont'd)
CROSSBAR & OUTER CROSSTUBE ASSEMBLY
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PART NUMBER
0300113
0301956
0302641
0302648
0400044
0400349
0400367
0400451
0400483
0400559
0707505
0712933
0718392
0719079
0719080
0803648
0803649
0806899
0806900
0806902
0807504
0904744
8600406
9012944
9030214
9043956
9047057
9052013
DESCRIPTION
GREASE FITTING, 1/4-28 STRAIGHT
STRAP, RUBBER 10" W/S-HOOK
SPRING - HOSE TENSIONER
T HANDLE
DRIVE SCREW, #10-24 X 1/2" RD HD
SCREW, 3/8"-16 X 3/4" FL HD SKT
1/4-20 NYLOCK HEX NUT ZP
1/4 FLAT WASHER ZP
LOCKWASHER, 3/8" COUNTERSUNK
3/16 X 1 ROLL PIN ZP
PLUNGER PIN
ALIGNMENT PIN
CROSSBEAM PIVOT PIN
END PLATE, LEFT
END PLATE, RIGHT
TIRE RESTRAINT, LH (SCOOP)
TIRE RESTRAINT, RH (SCOOP)
STINGER CROSSBEAM WELD'T
LH OUTER CROSSTUBE
RH OUTER CROSSTUBE
PIVOT SHAFT
PIN ASSEMBLY
WASHER - PIVOT PIN
PIPE PLUG, 1" NPT SKT HD
O-RING
3/8 NC X 3/4 BUTTON HD ALLEN
DETENT SPRING
BALL, 1" CHROME
29
124001734 BASKET STRAP KIT - STANDARD
0902382 1” NYLON POLY-COAT STRAP
0302647 CHAIN - RESTRAINT STRAP
0302657 1” TIRE RESTRAINT STRAP
0302658 1/4” PLATED MISSING LINK
I-11
QTY
5
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
-2
1
1
1
Section I - PARTS (cont'd)
RECOVERY BOOM & WHEEL LIFT HYDRAULICS
I-12
Section I - PARTS (cont'd)
RECOVERY BOOM & WHEEL LIFT HYDRAULICS
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NUMBER
0300011
0300044
0301522
0301620
0301825
0301921
0302508
0302584
0302919
0302922
0303017
0307097
0307460
0307576
0307579
0310289
810770015
DESCRIPTION
VALVE, 4 SPOOL CONTROL
CONNECTOR 6MJX8MB
CONNECTOR 6MJ-6MB
FITTING, ELBOW, 6MJ-6MB90
CYLINDER - EXTEND
HOSE ASSEMBLY, 128
ELBOW, 8MJ-8MB90LL
HOSE ASSEMBLY, 50" FOLD CYLINDER
HOSE ASSEMBLY, 170"
CONNECTOR 8MBX6FB
HYDRAULIC MOTOR, PARKER
FITTING, ELBOW, 6MJ-6MB90L
LIFT CYLINDER
WINCH ASSEMBLY, HY-246 NARROW DRUM
CONNECTOR, 8MJ-8MBL
HOSE ASSEMBLY, 29"
I-13
QTY
1
4
3
3
1
2
2
2
1
2
5
1
3
1
1
1
2
Section I - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
I-14
Section I - PARTS (cont'd)
PUMP, VALVE & FILTER HYDRAULICS
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART NUMBER
0300011
0300056
0300071
0300692
0301376
0301471
0301767
0301780
0302757
0302761
0303438
0310462
0400118
0400464
0400748
0702540
0807297
9011011
9012839
9018131
9018399
DESCRIPTION
VALVE, 4 SPOOL CONTROL
BARB, 16C4-16MP
HOSE CLAMP, 1"
STREET ELBOW, 1" 90°
CONNECTOR 8MJX10MB
HOSE ASSEMBLY - 30" LG
BARB, 16C4-16FJX
CONNECTOR, 8MJ-12MB
CONNECTOR, 8MJ-12MB
ELBOW, 16MJ-16MB45
HOSE ASSEMBLY - 92" LG
MAGNETIC HEX PLUG ~ 3/4 NPT
5/16-18 X 3/4 HHCS GR.5 ZP
5/16 HELICAL LOCK WASHER ZP
SCREW, 5/16"-18 X 1/4" HEX SKT SET
SUCTION HOSE, 12 FT (1" ID)
HYDRAULIC TANK WELDMENT
PIPE PLUG, 1/4" SQ HD
PLUG 1" (HYDRAULIC) HEX HEAD
BREATHER CAP
IMMERSION FILTER ASSEMBLY
I-15
QTY
1
1
2
1
1
1
1
1
2
1
1
1
2
2
2
2
1
1
1
1
1
Section I - PARTS (cont'd)
CONTROL ASSEMBLY
I-16
Section I - PARTS (cont'd)
CONTROL ASSEMBLY
ITEM
PART NUMBER
3014-791012
0300834
0300835
0301397
0302856
0302917
0307634
0307772
0307823
0307824
0400070
0400078
0400365
0400367
0400393
0400451
0400458
0400527
0721658
0722377
0722379
0806852
9053524
HD0900
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DESCRIPTION
CLEVIS - DUAL CTRL CABLE
KNOB, CABLE (IN-OUT)
KNOB, BOOM (UP-DN)
GREASE FITTING, 90 DEG
KNOB, TILT (UP-DN)
KNOB, WHL LIFT EXT (IN-OUT)
CONTROL CABLE 64" LG
3/4_PLUG
CLAMP CUSHION
CLAMP COVER PLATE
1/4-20 X 1 HHCS GR5 ZP
1/4-20 X 2 HHCS GR5 ZP
HEX NUT, 1/4"-28
1/4-20 NYLOCK HEX NUT ZP
3/8"-16 HEX JAM NUT
1/4 FLAT WASHER ZP
1/4 STAR LOCKWASHER ZP
CLEVIS PIN, 5/16" X 5/8" COTTERLESS
ROD CONTROL HANDLE PIVOT
PLATE- CONTROL HANDLE MOUNTING
SPACER
CONTROL HANDLE WLMT
BRONZE BUSHING (.752 X .879 X .750)
BEARING, ROD END, 1/4-28
I-17
QTY
1
2
2
8
2
2
8
3
4
4
8
4
12
12
8
8
12
1
2
2
2
8
16
8
Section I - PARTS (cont'd)
BOOM SWIVEL ASSEMBLY
ITEM
1
2
3
4
5
6
PART NUMBER
0300113
9056098
804181500
805180001
805180002
852060100
DESCRIPTION
GREASE FITTING, 1/4-28 STRAIGHT
SNAP RING, 1"
SHEAVE HOUSING CASTING
SHEAVE SHAFT
SHEAVE CASTING
CABLE GUIDE CASTING
I-18
QTY
1
2
1
1
1
1
NOTES
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement