HandA-Accessories.com

INSTALLATION

INSTRUCTIONS

PARTS LIST

Left fog light

Right fog light

Right fog light trim

Accessory

FOG LIGHT KIT

08V31-SEC-201

16 Wire ties

Application

TSX

Relay

Left fog light trim

2 Step-screws

(with thin rubber washer)

4 Self-tapping screws, 4 x 16 mm

2 Washer-screws, 5 x 16 mm

Publications No.

BII 24805

Issue Date

APRIL 2003

Fog light harness

Switch

Right bracket

Left bracket

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

2 Washer-screws, 4 x 8 mm

2 Step-screws

(with thick rubber washer)

Relay bracket

2 Spring nuts, 5 mm

2 Self-tapping screws, 5 x 18 mm

2 Washer-bolts, 6 x 12 mm

Flange nut, 6 mm

BII 24805 (0304) 08V31-SEC-2000-91

1 of 11

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

10 mm Combination wrench

Ratchet

10 mm Socket

Illustration of Fog Lights Installed on the Vehicle

SWITCH

RELAY

Installing the Fog lights

3.

Open the hood, and remove the radiator cover

(twelve clips).

CLIP

LONG

CLIP

SHORT

CLIPS (8)

LONG

CLIP

CLIP

RIGHT FOG

LIGHT

LEFT FOG

LIGHT

FOG LIGHT

HARNESS

2N04300S

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by “do-it-yourselfers.”

1.

Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.

2.

Disconnect the negative cable from the battery.

RADIATOR COVER

2410022T

4.

Remove two clips from the front grille.

5.

Remove the front bumper (five clips, two selftapping screws, and four bolts).

FRONT

BUMPER

2 of 11

BII 24805 (0304)

LONG

CLIP BOLTS (4)

SHORT CLIPS (2)

SELF-

TAPPING

SCREWS (2)

2410031T

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

6.

Release the three retaining tabs, and remove the left fog light cover.

8.

Install the left bracket to the left fog light with one step-screw (with thick rubber washer) and one step-screw (with thin rubber washer).

STEP-SCREW

(with thin rubber washer)

LEFT FOG

LIGHT TRIM

LEFT FOG

LIGHT

RETAINING

TABS (3)

FOG LIGHT

COVER

2N04010S

7.

Insert the spring nut onto the rib at the rear of the front bumper.

FRONT BUMPER

RIB

BRACKET

4 x 8 mm

WASHER-

SCREW

4 x 16 mm

SELF-TAPPING

SCREWS

STEP-SCREW

(with thick rubber washer)

2N04031S

9.

Install the left fog light to the fog light trim with one step-screw (with thin rubber washer) and two 4 x

16 mm self-tapping screws.

10. Position the fog light assembly in the opening of the front bumper with the retaining tab behind the front bumper. Install one 5 x 18 mm washer-screw and one 5 x 16 mm self-tapping screw.

FRONT BUMPER

5 x 18 mm

SELF-TAPPING

SCREW

SPRING

NUT

2N04020S

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

FOG LIGHT

TRIM

5 x 16 mm

WASHER SCREW

2N04040S

11. Repeat steps 6 thru 10 to install the right fog light.

BII 24805 (0304)

3 of 11

Routing the Fog Light Harness

12. Remove the air duct cover (three clips).

CLIPS (3)

AIR DUCT

COVER

14. Remove the two bolts that fasten the fuse/relay box, and remove the fuse/relay box.

BOLT

FUSE/RELAY

BOX

13. Remove the hood latch cover (three bolts).

2N04051S

FUSE/RELAY

BOX

BOLT

2N19320S

15. Remove the two bolts that fasten the air cleaner housing, and release the clip on the battery cable.

BOLT

CLIP

AIR CLEANER

HOUSING

BOLT

4 of 11

BOLT

HOOD LATCH

COVER

2N04062S

AIR INTAKE

TUBE

BATTERY

CABLE

BOLT

2N19311S

AIR INTAKE

TUBE

16. Disconnect the two air intake tubes, and remove the air cleaner box.

BII 24805 (0304) © 2003 American Honda Motor Co., Inc - All Rights Reserved.

17. Release the six retaining tabs and remove the fuse/relay box under cover.

RETAINING

TABS (6)

19. Continue to route the fog light harness along the vehicle harness.

FOG LIGHT

HARNESS

FUSE/RELAY

BOX UNDER

COVER

2N19330S

18. Route the two fog light harness terminals through the engine room and alongside the vehicle harness as shown.

FOG LIGHT

HARNESS

FOG LIGHT

HARNESS

TERMINALS (2)

VEHICLE

HARNESS

VEHICLE

HARNESS

2N19340S

2N04070S

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

BII 24805 (0304)

5 of 11

20. On the back of the fuse/relay box, unplug the vehicle 14-pin and 20-pin connectors from the fuse/relay box. Release the lock on the vehicle

14-pin connector, and push the fog light harness blue/black wire terminal into the vehicle 14-pin connector. Reattach the lock on the 14-pin connector.

20-PIN

CONNECTOR

14-PIN

CONNECTOR

23. Secure the fog light harness to the vehicle harness with one wire tie.

VEHICLE

HARNESS

FOG LIGHT

HARNESS

FUSE/

RELAY

BOX

As viewed from back side

VEHICLE

14-PIN

CONNECTOR

BLUE/

BLACK

WIRE

TERMINAL

LOCK

BLUE/

ORANGE

WIRE

TERMINAL

VEHICLE

20-PIN

CONNECTOR

Harness side view

VEHICLE

14-PIN

CONNECTOR

LOCK

Harness side view

FOG

FUSE/

RELAY

BOX

LIGHT

HARNESS

BLUE/

BLACK

WIRE

TERMINAL

WIRE TIE

RELAY BOX

UNDERCOVER

2410130T

24. Reinstall the fuse/relay box under cover.

25. Install the relay bracket to the relay with one

6 x 12 mm washer bolt and one 6 mm flange nut.

RELAY BRACKET

6 mm

FLANGE NUT

VEHICLE

20-PIN

CONNECTOR

FOG LIGHT

HARNESS

BLUE/ORANGE

WIRE TERMINAL

2017040Y

21. Release lock of the 20-pin connector, and push the fog light harness blue/orange wire terminal into the vehicle 20-pin connector. Reattach the lock on the 20-pin connector.

22. Plug the vehicle 14-pin and 20-pin connectors into the fuse/relay box.

6 of 11

BII 24805 (0304)

6 x 12 mm

WASHER-BOLT

RELAY

2410140T

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

26. Install the relay bracket to the vehicle frame with a 6 x 12 mm washer-bolt. (If already equipped with a vehicle bracket, remove the mounting bolt that secures the vehicle bracket, and attach the relay bracket with this bolt.)

VEHICLE

FRAME

6 x 12 mm

WASHER-BOLT or

VEHICLE BOLT

RELAY

30. Route the fog light harness (long wire) to the back of the left headlight, then secure it to the vehicle harness with three wire ties.

VEHICLE

FRAME

LEFT

HEADLIGHT

VEHICLE

HARNESS

RELAY

BRACKET

FOG LIGHT HARNESS

4-PIN CONNECTOR

2410150T

27. Plug the fog light harness 4-pin connector into the relay.

28. Secure the fog light harness to the vehicle harness with three wire ties as shown.

WIRE TIE

FOG LIGHT

HARNESS

FOG LIGHT

HARNESS

CLIP

WIRE TIE

2N04080S

31. Install the fog light harness clip to the vehicle frame.

32. Route the fog light harness under the adjusting point, then to the vehicle harness with one wire tie in the area shown.

VEHICLE

HARNESS

VEHICLE

HARNESS

FOG LIGHT

HARNESS

2N19360S

29. Reinstall the air cleaner housing and under-hood fuse/relay box.

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

BII 24805 (0304)

FOG LIGHT

HARNESS

WIRE TIE

2N04091S

ADJUSTING

POINT

7 of 11

33. Route the fog light harness along the vehicle harness, and secure it to the vehicle harness with five wire ties.

WIRE TIE

36. Connect the left and right fog light harness 2-pin connectors into the left and right fog lights, and reinstall the front bumper. Check that all clips, self-tapping screws, and fasteners are installed securely.

FOG LIGHT HARNESS

2-PIN CONNECTOR

RIGHT FOG

LIGHT

VEHICLE

HARNESS

FOG LIGHT

HARNESS

2N04100S

34. Remove the vehicle ground terminal, and attach the fog light harness ground terminal with the vehicle ground bolt.

VEHICLE

HARNESS

WIRE TIE

VEHICLE

FRAME

FRONT

BUMPER

2410210T

LEFT FOG

LIGHT

Installing the Switch

37. Remove the two self-tapping screws and one screw, from the steering column lower cover.

Push.

STEERING

COLUMN

UPPER COVER

RETAINING TAB

(6 places: Push.)

FOG LIGHT

HARNESS

CLIP

FOG LIGHT

HARNESS

VEHICLE

GROUND

BOLT

FOG LIGHT

HARNESS

GROUND

TERMINAL

2N04110S

35. Secure the fog light harness to the vehicle harness with one wire tie, and push the fog light harness clip into the vehicle frame.

STEERING

COLUMN

LOWER

COVER

SCREW

SELF-TAPPING

SCREW

2410220T

38. Lower the steering tilt lever, pull the steering wheel toward you. Release the six retaining tabs, and remove the steering column upper cover and lower cover.

NOTE: When removing the steering column upper cover, release the two front retaining tabs first.

8 of 11

BII 24805 (0304) © 2003 American Honda Motor Co., Inc - All Rights Reserved.

39. Turn the steering wheel 90° counterclockwise, and remove the two screws fastening the switch.

Move the vehicle harness up and out of the way.

Unplug the vehicle connector from the switch, and remove the switch.

VEHICLE

HARNESS

VEHICLE

CONNECTOR

VEHICLE

CONNECTOR

SCREW

2N04120S

SWITCH

40. Install the new switch provided where the old switch was removed. Then plug the vehicle connector into the new switch. Replace the vehicle harness.

42. Check that all wire harnesses are routed properly and all connectors are plugged in.

43. Reinstall all removed parts. Check that all clips and fasteners are installed securely.

44. Reconnect the negative cable to the battery.

45. Reset the clock, and reset the radio station presets.

USE AND CARE

How to Operate Fog Lights

• Turn the headlights “ON,” and make sure headlights are “ON” low beam.

• Turn the fog light switch “ON.”

The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.

Fog Light Aiming Adjustment

1.

Adjust the fog light:

• Adjust the aiming according to local laws and regulations.

• To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained.

VEHICLE

HARNESS

CONNECTOR

To raise To lower

2N04140S

SCREW

2N04130S

SWITCH

41. Reinstall the two screws removed in step 37.

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

BII 24805 (0304)

9 of 11

BULB REPLACEMENT

1.

Remove the one self-tapping screw and one washer-screw that fasten the fog light, and pull the light out toward you.

CONNECTOR

4.

Install the new bulb and socket into the fog light.

• Use only a genuine Honda halogen light bulb of specified wattage.

Rating: 12V 55W H11 Halogen Light Bulb

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a clean, soft cloth that has been dampened with a denatured alcohol or mild detergent solution.

FOG LIGHT

FOG LIGHT

SELF-

TAPPING

SCREW

BULB

2N04170S

WASHER-

SCREW

2N04150S

2.

Unplug the connector from the fog light, then remove the fog light.

3.

Remove the bulb.

5.

Reinstall the fog light in the reverse order of removal.

• Check that the wire harnesses are not pinched.

• Be sure to tighten the self-tapping screws securely.

FOG LIGHT

BULB

2N04160S

10 of 11

BII 24805 (0304) © 2003 American Honda Motor Co., Inc - All Rights Reserved.

CIRCUIT DIAGRAM

FUSE/

RELAY

BOX

BLU/ORN

BLU/ORN

RELAY

FOG LIGHT

HARNESS

BLU/YEL

BLU/BLK

LEFT FOG

LIGHT

BLU/YEL BLU/YEL

RIGHT FOG

LIGHT

BLK

BLK

FOG LIGHT

HARNESS

GROUND

BLK

OFF

HEADLIGHT SWITCH

OFF

-

Low Hi

-

ON ON -

BLK

YEL

BLU

GRN

RED

WHT

LT BLU

BLACK

YELLOW

BLUE

GREEN

RED

WHITE

LIGHT BLUE

BRN

ORN

PUR

BROWN

ORANGE

PURPLE

NAT NATURAL

PNK PINK

GRY GRAY

LT GRN LIGHT GREEN

© 2003 American Honda Motor Co., Inc - All Rights Reserved.

BII 24805 (0304)

11 of 11