GENUINE SATELLITE RADIO KIT
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the satellite radio kit. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
WARNING
• There are several
WARNING
and
CAUTION
sections in this booklet concerning safety when installing. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle.
WARNING:
Indicates a situation in which serious injury or death could result if the warning is ignored.
CAUTION:
Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions.
•
•
To ensure safety and reliability of the work, installation, removal and disposal work done by an Authorized Mazda Dealership is recommended.
Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
PART NAME: SATELLITE RADIO KIT
PART NUMBER: 0000 81 K02A
VEHICLE: Mazda3
NOTE
To the dealer
• Please turn over these instructions to the customer after installation.
To the customer
• Keep these instructions after installation. The instructions may be necessary for installing other optional parts or removal of this accessory.
• Should the vehicle or this accessory be resold, always leave these instructions with it for the next owner.
1ED6P11A06400
1
1
INSTALLATION VIEW
Mazda3
4-Door
ANTENNA
DLP UNIT
ANTENNA
5-Door
CABLE
DLP UNIT
CABLE
2
2
PARTS
Note
•
Verify that the kit includes all the following parts and that they are free of dirt, scratches or damage.
Part Part name Qty. Part Part name
Qty.
Part Part name
Qty.
Tie wrap 3 Pad protector 2 Clip 4
Owner’s
Manual
1
3
BEFORE INSTALLATION
Rating label
DLP unit
Sirius ID (ESN)
1
Rating Label Removal
1. Tear off lower part of the rating label on the bottom of DLP unit.
2. If there is nothing written in the Sirius ID (ESN) space of the rating label, write down the 12-digit number printed in the location shown in the figure.
3. Affix one rating label in the last page of the Owner’s
Manual.
Note
•
The other rating label is for the dealer (port) records.
•
Do not fail to submit the record.
Rating label
①
: Serial No.
②
: Sirius ID (ESN)
③
: VIN
①
Installation instructions
②
①
②
③
①
②
③
Tear off
Affix to the back of the Owner’s Manual.
Tear off
Submit to the manager of installation department.
3
REQUIRED TOOLS
Prepare the following tools or items before installation.
●
Electrical vinyl tape ●Mat ●Scissors ●Scale ●Touch-up paint or Zinc primer ●Phillips screwdriver
●
Socket driver (8 mm, 10 mm, 14 mm) ●File ●Fiber stick ●Wrench ●ISP alcohol
WARNING
When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries.
Disconnect the negative battery cable before removal/installation.
When connecting/disconnecting connectors, grasp the connectors, not the wires.
Otherwise a short, an accident from poor contact or fire may occur.
Do not pull the harness with excessive force. Doing so can cause a breakage or a short-related accident, as well as an electrical short or fire.
Secure the harness with the band (part included) so it doesn’t dangle. If not, it may cause a short, accident, or fire.
CAUTION
Put the removed parts and the parts in the kit on the protective sheet to prevent scratches.
Using improper tools may cause damage and or broken parts. Use the correct tool for the job.
Be sure to cover the vehicle body with protectors or mats to prevent stains, scratches and damage when removing/installing the vehicle parts.
Excessive length of tie wrap may interfere with other parts and cause damage.
Cut unnecessary part up to about 5 mm {0.19 in} from the fixed point.
WARNING
•
When removing/installing the parts, park the vehicle on level ground and apply the side brake securely. Be sure to turn the ignition switch off, otherwise the vehicle can move, causing personal injury or vehicle damage.
CAUTION
•
During the installation of the antenna cable make sure the cable is not pinched, knotted “kinked” or coiled too tightly. It is recommended that a coil of less than 20 mm {0.78 in} be avoided if possible.
•
If this wiring procedure is not followed, the performance of the antenna will be affected and could result in increased audio muting.
20 {0.78} mm {in}
Note
• When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory.
4
4
PART REMOVAL
Clip A
5
A
Decoration panel
CAUTION
•
Be careful not to damage or lose removed parts during removal.
Decoration panel removal
1. Pull the decoration panel outward and detach the clips A and tab B in the order shown in the figure.
2. Remove the decoration panel by sliding it towards the driver’s side to disengage the clip.
3
A
1
2
4
A A B
Tab B
Screw
Center panel module
Clip A
Antenna feeder plug
Connector
A
A
A
Front scuff plate
Screw
B
A
C
A
B
A B
C
Front
B
A
A
A
A
A
Glove compartment
Clip A
Locator pin B
Locator pin C
Center panel module removal
1. Remove the screws.
2. Disconnect connector and the antenna feeder plug.
CAUTION
•
Do not pull on the wiring harness.
Glove compartment removal
1. Remove the screws.
2. Pull the glove compartment outward and detach clips A and tab B.
3. Remove the glove compartment.
CAUTION
•
Be careful not to damage the scuff plate during removal.
Front scuff plate (passenger’s side) removal
1. Pull the front scuff plate upward, detach clips A, locator pins B and C from the body, and then remove the front scuff plate.
5
Rear scuff plate
A
C
A B
C
B
Front
Front side trim
Fastener
4-Door
Tire house trim
Front
5-Door
B
Tire house trim
A
B
A
Clip A
Locator pin B
Locator pin C
Clip A
Locator pin B
Locator pin A
C
B
Fastener
Locator pin B
Tab C
Locator pin B
Rear scuff plate (passenger’s side) removal
1. Pull the rear scuff plate upward, detach clips A, locator pins B and C from the body, and then remove the rear scuff plate.
Front side trim (passenger’s side) removal
1. Remove the fastener.
2. Pull the front side trim in the direction of the arrow and detach clip A and locator pin B.
Tire house trim (passenger’s side) removal
1. Remove the fasteners.
2. Pull the tire house trim outward and detach locator pins A and B (4-door).
3. Pull the tire house trim outward and detach locator pins A,
B and tab C (5-door).
4. Remove the tire house trim.
Front
A
Fastener
Locator pin A
6
4-Door
Fastener
5-Door
A
B
Tab
A
B
Fastener
Trunk end trim
A
B
A
B
B
A
B
A
Fastener
Locator pin B
B
A
Tab
B
A
Clip A
Trunk side trim
Locator pin B
Fastener
Fastener
Rear seat belt
Front
Clip A
Tab
Tab
Trunk end trim
Front
Service hole cover
Trunk side upper trim
Trunk end trim removal
1. Remove the fasteners.
2. Pull the trunk end trim upward, then detach clips A, locator pins B and tabs.
3. Remove the trunk end trim.
Trunk side trim (driver’s side) removal
4-Door only
1. Remove the fasteners, then remove the trunk side trim.
Trunk side upper trim (passenger’s side) removal
5-Door only
1. Remove the rear seat belt lower bolt.
2. Detach the tabs and remove the cover from the trunk side upper trim.
7
Trunk side upper trim
B
C
B
B
C
B
B
C
B
B C
B
A
C
B
C
B
A
Clip A
Screw
Cap
Tab B Tab C
Front
Fastener
Cargo net hook
Screw
Fastener
Rear combination light
Trunk side trim
Clip A
Connectors
N･m {kgf･cm, in･lbf}
3. Remove the cap and remove the screw.
4. Remove the fastener.
5. Pull the trunk side upper trim outward, then disengage tabs
B and C from the C-pillar trim.
6. Pull the trunk side upper trim outward, then disengage clips
A from the body.
Trunk side trim (passenger’s side) removal
5-Door only
1. Remove the screws, then remove the cargo net hooks.
2. Remove the fasteners.
3. Detach the clip A and remove the trunk side trim.
Rear combination light removal
(Note: On the 5-Door models remove the passenger side combination light only. On the 4-Door models remove the driver’s side combination light only)
1. Disconnect the connectors.
2. Remove the two nuts (10 mm).
3. Remove the rear combination light.
8
5
INSTALLING ANTENNA
Front
100 {3.93}
Trunk lid
Antenna
Center
100 {3.93}
Adhesion area
Trunk lid mm {in}
<Cross-sectional view>
Clip
Double-sided adhesive tape
Antenna
Center
15－20
{0.59－0.78}
565 {22.2} mm {in}
Clips (100 {3.93} interval)
Antenna cable mm {in}
<4-Door>
Note
•
The procedure for the 5-door model begins on page 12.
1. Clean the adhesion area on the trunk lid with ISP alcohol.
2. Affix the double-sided adhesive tape to the antenna.
3. Install the antenna in the position shown in the figure.
4. Clean the adhesion area of clip with ISP alcohol.
5. Attach the clips to the trunk lid.
6. Install the antenna cable to the clips.
9
Tie wrap
Antenna cable
Butyl tape
DLP unit
Yellow
Tie wrap
Pad protector
20－24 {0.78－0.94}
Double-sided adhesive tape
Tie wrap
Pad protector
Splitter mm {in}
Antenna cable
Seaming welt
Pad protector
White
Splitter
DLP unit
7. Secure the antenna cable to the rubber tube of the vehicle wiring harness with tie wraps.
8. Secure the antenna cable to the vehicle with a pad protector halves.
CAUTION
•
It is essential to follow the OEM harness as shown, failure to do so will result in problems when opening and closing trunk lid.
•
Always follow the indicated route.
9. Pull the seam upward and route the antenna cable in seaming welt. (Does not need to be completely removed)
CAUTION
•
Be careful not to tear the seaming welt when pulling it up.
10. Clean the adhesion area with ISP alcohol.
11. Secure the antenna cable in place with the butyl tape and pad protector halves.
12. Affix the double-sided adhesive tape to the splitter.
Note
•
Match the size of double-sided adhesive tape to the size of the splitter before cutting.
13. Connect the splitter cable to the DLP unit.
14. Secure the splitter to the side of the DLP unit with double-sided adhesive tape.
15. Secure the splitter cable with pad protector halves.
16. Affix a protector cushion to the back of the DLP unit.
Protector cushion
10
Pad protector mm {in}
270
{10.6}
Tie wrap
200
{7.8}
Tie wrap (long)
Front
Tie wrap
Antenna cable
DLP unit
Electro vinyl tape
Splitter
Antenna cable
Pad protector
Front
DLP unit
Front
17. Secure the tie wraps (long) under the pad protectors.
18. Affix electro vinyl tape around the edges.
•
CAUTION
Corners are sharp, the electro vinyl tape is intended to protect the installer and components from the sharp edges.
19. Connect the antenna cable connector to the splitter.
20. Install the DLP unit to the inside of the side body panel between the sheet metal and trunk compartment using tie wraps. (With the connector towards the rear of the vehicle.)
21. Bundle up the antenna cable into a loop as shown on page
4 using a tie wrap, and secure it to the vehicle panel with pad protectors.
•
CAUTION
Be sure to bundle the antenna cable into a loop.
<4-Door Procedure continues on page 15.>
11
Remove using a file
Antenna mm {in}
15－20 {0.59－0.78}
100 {3.93}
Adhesion area
Clip
3 {0.11}
9 {0.35} mm {in}
Center
100 {3.93}
Roof
Roof
Center
Seaming welt mm {in}
Antenna
Antenna cable
<5-Door>
1. File the hole where the rear combination light harness passes through as shown in the figure.
CAUTION
•
When filing, always use a mat or other protection to prevent shavings from getting into the vehicle interior.
•
Be sure to remove any burrs after filing.
•
Remove any chips or drill filings that may have fallen in the vehicle.
2. Using ISP alcohol, remove grease from around the holes and apply touch-up paint or zinc primer for rust prevention.
3. Clean the adhesion area on the trunk lid with ISP alcohol.
4. Install the antenna in the position shown in the figure.
5. Clean the adhesion area of the clip with ISP alcohol.
6. Attach the clip to the vehicle as shown in the figure.
7. Install the antenna cable to the clip.
12
Seaming welt
Pad protector
Antenna cable
Double-sided adhesive tape
Antenna cable
Antenna cable
Vinyl tape
25 mm {0.98 in}
Butyl tape
Pad protector
DLP unit
50 mm {1.96 in}
Pad protector
8. Pull seam upward and route the antenna cable in the seaming welt. (Does not need to be completely removed)
CAUTION
•
Be careful not to tear the seaming welt when pulling it up.
9. Reinstall the rubber seaming welt to its original position.
10. Clean the adhesion area with ISP alcohol.
11. Secure the antenna cable in place with pad protector halves.
12. Route the antenna cable into the trunk compartment
with the vinyl taped portion in the filed-out part of hole.
13. Affix butyl tape in the position shown in the figure.
14. Clean the adhesion area with ISP alcohol.
15. Affix double-sided adhesive tape to the DLP unit.
16. Adhere two overlapped pad protector halves to the DLP unit.
•
Note
See Step 22 for additional illustration.
13
Double-sided adhesive tape
Splitter
DLP unit
Front
Tie wrap
Antenna cable
DLP unit
White
Splitter
Pad protector
Yellow
Front
Pad protector
Electro vinyl tape
DLP unit
Tire house
Antenna cable
Splitter
DLP unit
Pad protector
17. Affix the double-sided adhesive tape to the splitter.
Note
•
Match the size of double-sided adhesive tape to the size of the splitter before cutting.
18. Connect the splitter cable to the DLP unit. double-sided adhesive tape.
20. Secure the splitter cable with pad protector halves.
21. Affix pad protector and electro vinyl tape around the edges. double-sided adhesive tape against the wheel well and tire housing.
23. Connect the antenna cable connector to the splitter.
24. Clean the adhesion area with ISP alcohol.
25. Secure the antenna cable to the vehicle with pad protector halves.
26. Bundle up the antenna cable into a loop using a tie wrap, and secure it to the vehicle panel with a pad protector.
CAUTION
•
Be sure to bundle the antenna cable into a loop as shown on page 4.
14
6
INSTALLING THE CABLE
Audio box
Dashboard member
20 {0.78}
Connector
Tie wrap
Tie wrap
Front
Front
Cable
Tie wrap
Cable
Pad protector
B-pillar lower trim
Cable mm {in}
Front
Pad protector
Cable
1. Route the cable through the back of the dashboard member.
2. Pull the 16-pin connector (white) 20 mm {0.78 in} out from the audio box.
3. Secure the cable to the inside of the glove compartment with tie wraps (long).
4. Route the cable through the inside of the front side trim and secure it with a pad protector half and a tie wrap
(long).
5. Route the cable through the inside of the front scuff plate and secure it with a pad protector halves.
15
4-Door
Front
5-Door
Front
Tie wrap
Cable
Front
Front
B-pillar lower trim
Pad protector
Cable
Tie wrap
Pad protector
Cable
Front
Tie wrap
Cable
DLP unit
6. Route the cable through the inside of the rear scuff plate and secure it with a pad protector halves.
7. Secure the cable to the vehicle wiring harness with the tie wraps.
<4-Door>
1. Connect the cable connector (black) to the DLP unit.
2. Route the cable through the inside of the trunk compartment, secure it to the cable using tie wraps and pad protectors.
16
Cable
Tie wrap
Cable
DLP unit
Front
<5-Door>
1. Connect the cable connector (black) to the DLP unit.
2. Bundle up the cable into a loop and secure with tie wraps, then two pad protectors.
Pad protector
DLP unit
7
REINSTALLATION OF VEHICLE PARTS
• Install in the reverse order of “4. Part removal”.
CAUTION
•
After installing the vehicle parts, check for dirt. Clean any dirty parts.
• Perform the Inspection indicated on the last page of these installation instructions.
Note
•
After completing the installation, refer to the owner’s manual for instructions on how to reset the clock and preset radio stations, and record the trip meter numbers on the check sheet.
17
8
INSPECTION
• Inspect the installed / reinstalled parts for the following items.
• Inspection parts differ depending on the vehicle.
Inspection Parts
Clearance/Fit
Inspection Items (○)
Scratches/
Dirt/
Harness interference
○
○
Installation/
Tightening/
Engagement
○
○
Operation check
Rear combination light
Trunk side trim
Trunk side upper trim
(4-Door)
Trunk end trim
Front side trim
Front scuff plate
Rear scuff plate
Tire house trim
Glove compartment
Center panel module
Decoration panel
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○ ○
○
○
: Applicable
*1: Refer to the Owner’s Manual and the SATELLITE RADIO instruction manual, and verify that the system operates correctly.
Ex.: Turn the power ON, increase the volume, and press the SAT button.
• Direct access channel 184 is a test channel provided by Sirius.
Press the SAT button on the radio, and if properly installed you will receive a signal from the Sirius broadcast.
Note: Sirius broadcasts can only be received in an open area, enclosed spaces such as garages or work buildings block the satellite reception.
Date , ,
Vehicle.
VIN.
The term of validity for this sheet: 3 months
18
