User manual | LW2401 Quick Start Guide

LOREX
LOREX
LIVE
Wi r e l e s s Vi d e o H o m e M o n i tor
LW241/LW2401 Series Quick Start Guide
Getting Started
A. Camera Setup
1
4
Slide the power switch up, to the
ON position.
The Camera can be placed on a flat
surface, or wall mounted.
Determine where you want to locate the
camera.
NOTE: Keep cables and wires at least
3 feet (1 meter) away from infants or
young children. Use the included cable
clips as necessary.
Desk/Counter Mount
Wall Mount
NOTE: AVOID INSTALLING IN A LOCATION WHICH REQUIRES THE WIRELESS
SIGNAL TO PASS THROUGH CEMENT, CONCRETE AND METAL STRUCTURES.
THIS WILL REDUCE THE TRANSMISSION RANGE.
B. Video Monitor Setup
1
Insert the included microSD card,
as indicated on the right side of
the video monitor.
2
Connect the power adapter to a
power outlet, and to the video
monitor or charging cradle. If
you use the cradle, ensure the
video monitor firmly rests on
the cradle. The video monitor’s
charging LED indicator glows
red to indicate charging is in
progress.
OPTIONAL
The camera features mounting holes on the bottom
of the base and can be mounted to a wall if
desired.
Determine the camera position that will give you
the best view before permanently wall mounting the
camera. Ensure the power cable is long enough to
power the camera.
The Lorex Live Wireless Video Home Monitor comes with
the following components:
1 x Rechargeable Video Monitor
1 x Monitor Charging Cradle
Please refer to the Owner’s Manual for a mounting
template and full instructions on how to wall-mount
your camera.
2
1 x Wireless Camera(s)*
OPTIONAL: You can use ‘AA’
batteries or a rechargable battery
pack to power the camera. Please
refer to Appendix A in the Owner’s
Manual for instructions.
NOTE: Battery operation is suggested
for temporary monitoring only.
1 x microSD card
1 x Power Adaptor (for receiver)
1 x Power Adaptor (for camera)*
3 x Cable Clips*
Driver CD
Instruction Manual
Quick Start Guide
Connect the Power Adaptor to
the 5V Input on the back of the
camera.
3
Connect the power adapter to a
power outlet.
NOTE: It takes 6 hours to fully charge
the video monitor.
3
Slide the power switch up to the
ON position. The video monitor
will automatically scan for
cameras in range.
*Number of cameras and power adaptors may vary by model. Check
your package for specific content information.
FOR MORE INFORMATION:
www.lorextechnology.com
LW2401 Series QSG_EN_R1 Page 1
LOREX
LOREX
LIVE
Wi r e l e s s Vi d e o H o m e M o n i tor
LW241/LW2401 Series Quick Start Guide
C. Video Monitor Overview
Auto LED
Glows blue when auto-record is
enabled. Blinks when monitor is
in Scan mode.
Menu Button
Press to access the monitor menu
options. Press Menu again to exit.
Video Button
Press the Video button
to turn off the screen.
The speaker will
remain on.
Joystick
Use to navigate
monitor menus. Press
down on the joystick
to confirm a selection.
Audio Level
Indicator
Displays the level
of sound detected
by the camera.
Volume Control
Press + / - to control
the volume level.
Power LED
Glows green
to indicate unit
is powered on.
Blinks when the
battery is low.
Talk Button
Hold the talk button to
enable two-way audio
between the video
monitor and camera.
Charging Cradle
Charges the video monitor’s battery.
Microphone
Allows you to speak to the person on
the camera side when you press the Talk
Charging Cradle button.
Music Buttons
Press the
button once to begin playing a tune.
Press the
button again to stop the tune.
Press the
4 Camera Setup Example
Antenna Switch
Slide the Antenna Switch
towards the unlock position to
reveal the antenna.
Manual Recording
Starts manual recording.
Camera 1
Auto Recording
Turn auto recording on.
Receiver
Speaker
Outputs sound received from the camera.
Power Port (DC5V)
Connect the power adapter to the
charging cradle.
Kitchen
D. Changing Video Monitor Settings
1
Press the Menu button to access the
video monitor menu.
2
Use the joystick to navigate the
menus by moving it to the left, right,
up or down.
Camera 2
Family Room
Camera 3
Camera 4
button to skip to the next tune.
ON/OFF Switch
Slide the power switch to
the ON position to turn the
video monitor on.
ON
OFF
microSD Card Slot
Insert a microSD card to record video.
Press down on the joystick to confirm
a selection.
Sequence/ Quad Button
Press the Sequence/Quad button to view video in quad mode
(4 screen split view), or in sequence view.*
Scan Button
Turns off the video monitor, and waits for a camera to detect
sound to trigger the monitor to turn back on.
Charging LED Indicator
Glows red to indicate video monitor is charging. Glows green
to indicate video monitor is finished charging.
Power Port
Connect the power adapter into the power port.
Mini USB
Connect a mini USB cable (included) between the video
monitor and a computer to view video from your PC or
remotely (setup required).
Cam Button
Press the Cam button
to switch between
channels 1-4.*
Nursery
Garage
Pets
Register Now to Receive a 3
Month Warranty Extension!
Visit:
www.lorexTECHNOLOGY.com/warranty
It’s all on the Web
More Exciting Features
See Owner’s Manual for details on some of the following additional features:
• Video recording
• Room temperature monitoring
• Viewing your camera remotely
For detailed setup information,
please refer to your Owner’s
Manual. For additional information
and accessory purchases, please
visit our website:
www.lorextechnology.com/support
*Requires multiple cameras. Accessory cameras sold separately (model # LW2401AC1)
FOR MORE INFORMATION:
www.lorextechnology.com
©2011 Lorex Technology Inc.
As our product is subject to continuous improvement, Lorex Technology & subsidiaries reserve the right to modify product design, specifications & prices
without notice and without incurring any obligation. E&OE
LW2401 Series QSG_EN_R1 Page 2

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project