SBB500ss Sonic Bomb® Alarm Clock

INSTRUCTIONS
ALARM CLOCK WITH BED SHAKER
MODEL SBB500
LE ©
16 LE
© © [+]
5
14 ооовооововоовововеве
е 606060 866
100000000000 00 0000
© осо
| 6006050650 600060650665606
1 iGO
5bo0000000000000000
VEHATÉE AH H5000006000
6 665606566060
sypoc0o0o00
Sonic Alert
SD
AL/BET ны
00000
Figure B
Features shown on diagrams above:
1) Alarm Indicator 7) Alarm off Button 13) AC Adaptor Input
2) P.M. Indicator 5) Alarm Function Switch 14) Tone Control Wheel
3) Snooze Button 9) Hour Button 15) Vibrator Output
4) Volume Wheel 10) Minute Button 16) Flashing Light Display
5) Alarm Set 11) Battery Compartment 17) Hour Format & Power Cycle
6) Time Set Button 12) Dimmer Switch
Setting the correct time-
1) Press and hold the Time Button (6) at the same time press the hour button (9) to advance
the clock display rapidly until the hour is correct.
2) Press and hold the time button (6) at the same time press the MIN button (10) to advance
the minute until the correct time 1s shown.
3) A lighted dot (2) in the upper left clock display indicates time is PM. For AM time
indication, there 1s no lighted dot.
Setting the alarm time-
|) Simply follow the instructions mentioned under " Setting the correct time” except that you
will have to press the Alarm Button (5) instead of the TIME Button.
2) Make sure the alarm time 15 correctly set for AM or PM lighted dot (2) indicates PM. Be
sure to release the HOUR and MIN set buttons before releasing the ALARM button.
Waking To Alarm-
1) Set Function Switch (8) to choice of VIB/BUZZ or VIB or BUZZ.
2) Set desired volume (4) for Buzz sound.
3) Set alarm wake time per instructions for setting alarm time above.
Battery Backup-
To use battery backup, you can install a 9-volt alkaline battery in the back of the clock located
under the battery cover (11). Battery not included. Note the LED display will not show during
power failure but the clock will still be running and keeping proper time until the power comes
back.
NOTE: For best results it is recommended that the battery be changed every 6 to 8 months. If
the clock 1s not used for a while, it is recommended to remove the battery to avoid
leakage.
Shutting Off Alarm-
Alarm can be shut off temporary for the day or permanently shut off.
1) When the alarm goes off, simply press the AL off button (7) the alarm will shut itself off
for the day and come back on the next day at the same time if alarm setting has not
changed.
2) To shut the alarm off permanently, slide function switch (8) to off position. Alarm will not
come on until Function Switch (8) is set to "VIB" or "BUZZ" or "VIB/BUZZ" position.
Snooze Operation-
SNOOZE button (3) - press after alarm has sounded. The alarm will be turned off for 9
minutes for extra sleep. The alarm will come back again after 9 minutes. You may repeat
many times up to 1 hour.
Alarm-
Set the alarm time you wish and slide the VIB /f BUZZ / OFF (8) switch to the desired position.
Set to VIB for bed shaker and BUZZ for sound, or VIB/BUZZ for both.
Tone-
Adjust the tone (14) by rotating the tone wheel located on the right hand side just below the
volume wheel (4) until you reach desired level.
Volume-
To adjust the volume (4) rotate the wheel located on the upper right hand side.
Bed Shaker / Vibrator- Figure B
1) Attach the bed shaker jack to the back of clock at VIBRATOR input (15).
2) To turn on vibrator slide function switch (8) to VIB or VIB/BUZZ position.
3) Place vibrator under mattress or pillow.
AC-9V Power Input -
Attach the AC power supply input to the side of clock at AC-9V IN (13) next to the
VIBRATOR input (15), smaller input of the two. Important: do not confuse AC input with
vibrator input.
Hour Format and Power Cycle (17)
Please select the appropriate settings for use. For USA please select 12/60Hz; for Europe
please select 24/50Hz; for UK please select 12/50Hz. Please note the incorrect selection of
power cycle will result in incorrect time.
Made in China
Sonic Alert 1050 East Maple Rd, Troy, MI 48083
www.SonicAlert.com 1-800-566-3210 V/TTY