Minimum Specifications Tender`s Specifications FT4 1. MODEL a

Minimum Specifications Tender`s Specifications FT4 1. MODEL a
Minimum Specifications
Tender’s Specifications
1. MODEL
a) The unit shall be current model
of a reputable manufacturer.
Year
Make
Center articulated, four-wheel drive
tractor, for sidewalk sanding,
snow removal & sweeping, complete
with folding five position plow
and a sander.
Trackless Model MT6 or equivalent
b) Shop repair manuals, operator's
manuals, and spare parts manuals
must be included at time of
delivery.
Model
Engine Model
Yes
No
2. VEHICLE WEIGHT & HEIGHT
The tractor (basic) minimum weight
shall be 1852 kg (4089 lbs.)
Specify
The Tractor shall be a maximum height
Of 80” from ground to highest point of cab
Including any lighting.
3. ENGINE
a) The engine shall a
Water cooled diesel and
shall be a minimum of 110 h.p.
@ 2500 RPM
Specify
b) Dual element dry type air cleaner.
Yes
No
c) Full flow spin on oil filter.
Yes
No
d) High engine temperature and low
oil pressure complete with
automatic shut down device.
Yes
No
e) Engine block heater minimum 1500
watts.
Yes
No
FT4
Minimum Specifications
Tender’s Specifications
4. COOLING SYSTEM
a) Pressurized water cooled system.
Yes
No
b) Heavy duty radiator core complete
with all appropriate guards.
Yes
No
c) Hydraulic oil cooler.
Yes
No
d) Long Life Anti-freeze to -37oC.
Yes
No
a) Heavy duty hydrostatic drive.
Yes
No
b) Live PTO shall be supplied.
Yes
No
c) Four-wheel drive complete with
differential lock.
Specify
5. TRANSMISSION
6. STEERING
Centre point articulation steering
wheel controlled.
Yes
No
Yes
No
7. BRAKES
Hydraulic actuated foot brake
complete with mechanical parking
brake.
Specify Type_____________
8. WHEELS AND TIRES
a) Manufacturer's standard wheels
Yes
10-16.5 NHS winter grip tires, minimum.
b) A spare wheel and tire as above.
No
Yes__________No
9. ELECTRICAL SYSTEM
a) Heavy duty 12 volt system.
Yes
No
b) Heavy duty battery minimumo 950
cold cranking amperes at 0 C.
Yes
No
c) Two head lights, two tail signal
lights complete with four-way
hazard warning lights.
Yes
No
d) Back-up lights and reversing alarm
Yes
No
FT5
Minimum Specifications
Tender’s Specifications
e) Two-speed windshield wipers.
Yes
No
f) Windshield washer.
Yes
No
g) Interior cab lights.
Yes
No
h) 12V strobe light with blue lens
sliding pedestal mount rear of cab
Yes__________No
i) Lights and reflectors as required
for commercial vehicle by the M.T.O
all lighting shall be LED
Yes
No
j) 12V dual horns.
Yes
No
k) Minimum 95 amp alternator
10.
Specify
HYDRAULIC SYSTEM
The hydraulic system shall be of
Yes
sufficient capacity to operate all
equipment and available accessories
complete with all filters, controls
and safety valves. Unit to equipped
with auxiliary gear pump and valve to
operate front mount hydraulically driven
14 ft mower deck or a sweeper.
11.
CAB
a) Certified ROPS type (meets SAE
specifications).
Yes
No
b) High output in-cab heater and
defroster, with multi-speed fan
Yes
No
c) Air conditioned cab with unit
mounted at rear of machine (not
roof top unit)
d)
No
Two outside rearview mirror
mounted on the left and right
Yes__________No
Yes
No
e) Interior rearview mirror.
Yes
No
f) Sunvisor.
Yes
No
g) Tachometer, speedometer, hourmeter, temperature gauge, oil
pressure gauge and hydraulic
oil temperature gauge.
FT6
Specify
Minimum Specifications
Tender’s Specifications
h) Am/Fm radio with minimum dual
speakers
Specify
i) High back cloth covered air ride
seat complete with seat belts, or
approved equivalent.
Yes
j)The cab shall meet current noise
Specify
No
abatement requirements, 85 dBA
maximum
12.
BLADE
a) Five position Folding Blade capable of
operating in one of five positions,
Angle left, angle right, straight,
V plow or scoop forward
b) Hydraulic control shall provide
the following positions: raise,
hold, power angle and float.
13.
Specify
Yes
No
SANDER
a) Rear mounted sand/salt spreader,
PTO or hydraulic driven, with a
minimum capacity of 5 cu. ft.
Specify
b) Sander shall have a total width
of approximately 44” with a spread
width of not more than 41”
14. ACCESSORIES
a) This unit will be equipped with a reversing
Specify
colour camera system mounted in a secure,
safe, functional area on the unit and the
monitor will be mounted in a environmentally
appropriate area for maximum reversing
viewing for the operator. The following color
camera and accessories shall be supplied or
an approved equivalent: Veilig Reversing
Camera model number RDV-007S, 7”LCD colour
monitor, 130dgr camera with low-lighting LEDS,
5m video harness and all standard mounting
hardware.
15.
COLOUR
Manufacturer's standard colour.
FT7
Yes
No
Vehicle Minimum Specifications
Tender’s Specifications
MODEL
The unit shall be a current model of a reputable
Manufacturer
Make
Model
One 74 ft working height aerial(10ft elevator 60 ft boom)with
a aluminium line box mounted on a 37,000 lb. GVW
chassis
VEHICLE WEIGHT
G.V.W.R. 37,000 lbs minimum.
State minimum safe payload of complete truck body and
aerial device
C.A. – 143” minimum
Wheelbase 215” minimum
ENGINE
Engine Net rate hp 260 HP minimum.
800 lb-ft torque @1400rpm
Air Cleaner , heavy duty type with in
cab air restriction gauge
Horton Drive-master air operated cooling fan
Cold engine starting aid specify type
Engine Model
Specify
Yes
Specify
COOLING SYSTEM
Heavy duty rad core
Antifreeze to -35ºC Long life
Factory installed block heater
Silicone hoses and spring loaded clamps
Specify
Yes
Yes
ELECTRICAL SYSTEM
Alternator – 160 amp minimum
Back-up alarm
Batteries, 2 heavy duty 12v combined 1850 cca minimum
EXHAUST
Single horizontal muffler horizontal tail pipe drivers side
discharge
Exhaust system particulate traps must be located in a
position that will not interfere with the mounting/operation of
the aerial equipment
STEERING
Heavy duty power steering
Turning radius …state minimum
No
No
Specify
Yes
Specify
No
Yes
No
Specify
Yes
State:
FT8
No
No
Vehicle Minimum Specifications
Tender’s Specifications
TRANSMISSION
Allison automatic transmission 3500 RDS (Scan to be
provided by winning bid)
Transmission must be filled synthetic fluid
External, auxiliary transmission oil cooler
Transmission mounted hydraulic piston pump
Yes
No
Yes
No
Yes
No
Model ____________
GPM ____________
PSI ____________
REAR AXLE
Single reduction rear axle with ratio providing 62 mph road
and driver controlled locking differential
Rear Axles capacity 23,000 with 31,000 lb rear spring
capacity
Specify
Specify
FRONT AXLE
14,000 I beam type
Heavy duty Front shocks
Yes
Yes
No
No
WHEELS AND TIRES
Dual rear wheels.
Rear discs 22.5 painted steel hub piloted
Rear tires – first Michelin 11R22.5 XDE
Front rims 22.5 painted steel
Front tires Michelin XZY 315/80/R22.5
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
FUEL SYSTEM
Fuel tank - Minimum 190 litres
Fuel tank passenger side mounted under passenger door
Heavy duty fuel water separator
Specify
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
Yes
Specify
Yes
Yes
No
Yes
Yes
No
No
BRAKES
Full air with ABS
Front Brakes air s-cam brakes 16.5 x 5.0
Rear brakes air s-cam 16.5 x 7.0 with 30/30 long stroke
chambers and heavy duty spring activated parking brake
Provision for electric trailer brakes
Air Compressor 13.5 CFM capacity minimum
Air Dryer AD-IP Bendix with heater
Air tank drain valves with cables mounted near the driver’s
access steps
Dust shield to fitted at all wheels
Haldex automatic slack adjusters front and rear with
stroke indicators at all wheels
FT9
No
No
Vehicle Minimum Specifications
Tender’s Specifications
CAB & CHASSIS
Conventional cab with sound suppression insulation for
noise attenuation to 74 dbA
Tilt Style hood
Dual air horns
Seats dual bucket air ride vinyl seats. Both seats to be air
suspended high-back with head rest and arm rest,
National 2000 or equivalent
Floor covering - rubber, heavy duty
Dual sunvisors
High output heater with CFC free R134 air conditioning
Mirrors - two outside, 7" x 16", minimum, heated power
adjust West Coast type, with clearance lights
Two stainless steel front fender mirrors
Two 8” integrated stainless steel convex mirrors
Am/fm radio with two speakers mounted in dash or door
panels with grill covers
Variable intermittent windshield wipers
Hour meter
Power windows both sides
Full gauge set including oil pressure,
engine temperature, air pressure gauges,
speedometer, tachometer, volt gauge, fuel
gauge as a minimum. Truck dash to rocker
style illuminated switches
Grab bar at each door to assist entry to cab
Two in -cab 12v power points
Cab front fender rubber/fender extrusions fitted
Stainless steel boot brushes to be installed both sides
FRAME
Full depth frame front to rear
Double frame from rear spring shackle to front spring
shackle
RBM minimum 2,749,000 in lbs
Two front mounted tow hooks
UTILITY BODY
To supply and install one (1) Eloquip or equivalent line body
of fabricated aluminium construction suitable for mounting
on a single axle cab and chassis. Manufacturer of body
must provide at least two municipal reference for which the
have built a body to used with a forestry aerial
State brand of body being bid
FT10
Specify dbA
Yes
Yes
Specify
No
No
Yes
Yes
Yes
Specify
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Specify
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
No
No
Specify
Yes
No
References
State:
Vehicle Minimum Specifications
Tender’s Specifications
All body cross-members welded on 12” centres
All Aluminum sheeting must 5083 grade
All aluminum extruding will be 6061 grade
Body floor, side and front walls to ¼” aluminum
Aluminum grip-struts fitted over the top of all compartments
All doors to have check chains or cables contained within
vinyl tubing or that are coated
Aluminum drip moldings to be provided over all doors
All door handles to be recessed “T” type or paddle type
stainless steel bolted to the outer door and have keyed alike
type locks
Stainless steel fasteners and hardware to be used
Stainless steel heavy duty hinges to be used
Stainless steel slam/adjustable latches
Heavy duty grade automotive grade door gaskets, tubular
and non-porous
Separate aluminium /steel lined wheel well sections
Fender panels to have fender extensions at each wheel well
to reduce excessive body splash
Cargo surface area to be treated with anti-slip material
Mudflaps with anti-sail feature behind rear wheels
Aluminum splash guards in front of rear wheels
One bumper mounted cone holder capable of handling 28”
cones, front mounted so as not to interfere with tipping of
hood
One rear mounted cone holder capable of handling 28”
cones
Storage bracket for shovel, broom, rake to be provided at
an area of suitable convenience
All compartmental shelving and dividers to be of aluminum
construction. Shelving lips to be 2” minimum height
All doors recessed or flush mounted to the body facing
CURBSIDE COMPARTMENTS
There shall be walk up area to cargo area and four (4)
compartments fitted to the positions as indicated below with
#1 as being the most forward adjacent to the cab
#1- 25” wide x 48” high x 18” depth fitted with nine (9)
aluminum swiveling hooks of suitable diameter three per
wall
#2 -25” wide x 48” high x 18” depth fitted with nine (9)
aluminum swiveling hooks of suitable diameter three per
wall
FT11
Yes
No
Yes
Yes
Specify
No
No
Yes
Specify
No
Yes
Yes
Yes
Specify
No
No
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
No
Yes
No
Specify
Yes
No
Yes
No
Yes
No
Yes
No
Vehicle Minimum Specifications
Tender’s Specifications
#3 – 27” wide x 48” high x 18” depth. This area is to provide
a walk up access to the cargo deck. Steps must be safety
grip strut type. Two full height aluminium access handles
shall be fitted
# 3 – Two (2) 10” deep x2” wide slots fitted to body and an
8” x 2” hardwood or heavy duty plastic drop in board
supplied at the walk up area
#4 – 98” wide x 24” high x 18” depth to be provided for
chainsaw storage. This area shall also be vented in a
manner as to prevent water ingress
#5 – 24” wide x 24” high x 18” depth complete with one
height adjustable shelf
All shelving and bottoms of compartments are to be lined
with rubberized matting
STREET SIDE COMPARTMENTS
There shall be five (5) compartments fitted to the body side
positions and a sixth (6th) rear cabinet as indicated below
with #1 being the most forward adjacent to the cab
#1- 25” wide x 48” high x 18” depth with two (2) adjustable
shelves
#2 -25” wide x 48” high x 18” depth with one (1) adjustable
shelf
#3 - 25” wide x 48” high x 18” depth with three (3)
adjustable shelves
#4 – 98” wide x 24” high x 18” depth to be left open for
storage purposes
#5 - 24” wide x 24” high x 18” depth, vented for fuel storage
6- Street side rear to have an access door of approximately
15” wide and 13” high with a “hotstick shelf in compartments
2,3,4,5. shelf to have hotstick holders fitted #
All compartments bottoms to lined with rubberized matting
All compartments street & curb shall be lit with “fibreglo”,
“vista” or equivalent type lighting and focus to optimize
illumination in that compartment area. The lighting shall be
controlled by in-cab master switch.
All compartment shall be vented by flow through venting
system with moisture proof front inlet and rear exit vents
which shall provide an unimpeded air flow
All compartment tops shall be fitted with aluminum anti- skid
grip strut for walking upon
There shall be one (1) aluminum upper storage
compartment , top opening and fitted parallel to the back of
the cab
FT12
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
Yes
No
No
Yes
Specify
No
Yes
No
Yes
No
Yes
No
Vehicle Minimum Specifications
Tender’s Specifications
Compartment to be 24” wide x 30” high x 56” length
Yes
No
There shall be an aluminum upper storage compartment
top opening, 18” wide x 16” high x 96 “ long fitted to the top
of upper of the street side compartments
Compartments to be fitted with an aluminium lid of sufficient
strength and anti-skid safety grip strut for walking upon
Lid lift to be assisted by gas strut cylinders both units
Heavy duty automotive grade gaskets, tubular and nonporous for both compartments
All stainless steel hardware recessed “T” or paddle type
handle and fitted with a lock assembly, both units
Vendor to supply and mount curbside a removable 6” swivel
base vise. Mounting location to be determined at pre-build
meeting
Yes
No
Yes
No
Yes
Yes
No
No
Yes
No
Yes
No
Yes
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
No
Yes
No
Yes
No
Yes
No
BODY REAR
Rear mounted frame reinforced pintle hook (Holland PH30)
with safety chain loops and wiring for 6 terminal electrical
plug.
Two (2) full length aluminium access handles to be fitted at
either side of the rear body rear.
Backup alarm
Supply and install rear grip strut type bumper with suitable
access steps to the body interior and indented for pintle
hook usage. Full length aluminium handles both sides for
body access
ELEVATOR BASE GUARD
Supply & install elevator base guard. Guard shall be 12"
high from floor& removable for elevator service.
BODY ELECTRICAL
A complete wiring diagram must be provided
All lighting and wiring connections to be assembled with
dielectric grease
Body lighting and reflector system shall fully comply to all
Canadian legal requirements and DOT/MTO standards
Rear directional & taillights to be protected from impact
corrosion and water damage
Body clearance lights to be wired into the chassis marker
clearance lights system and must be circuit breaker
protected.
Grote brand LED stop & tail lights with separate back up
lights
FT13
Vehicle Minimum Specifications
Tender’s Specifications
Wiring to be Grote Ultra Blue Seal sealed wiring system
Yes
No
Red and amber clearance lights to be installed to the front
and rear, right and left sides of the body.i
Tail/brake light assemblies to be either recessed and antshock rubber mounted within body structure or protected
with steel guards or mesh
Wiring to be loomed, secured, ty-wrapped or placed in
conduit. Wire passing through metal are to be protected
with rubber grommets
Four (4) deck lights are to be provided. Chassis auxiliary
switches may be used. Location to be determined at prebuild meeting
Two (2) amber rotating beacons mounted cab guard at front
corners
Two (2) Sparton or equal remote control spot/flood lights
with covers (mounting position to be discussed at pre-build
meeting
Two (2) Whelen 900 series 9”x7” vertically mounted flashing
amber strobes mounted on front truck grille
Yes
No
Yes
No
Yes
No
CAB GUARD ASSEMBLY
Heavy duty fabricated aluminium over the cab protection
guard assembly with weatherproof (marine grade) drip
board, full length and full width to be fitted to this unit
Assembly shall be constructed of aluminum tubing or angle
with heavy duty strut or expanded metal mesh with self
cleaning feature for walking surface on top
Assembly shall terminate at front bumper
Framework shall not interfere with cab ingress/egress nor
the full forward tilting of the front hood assembly
Grille/mesh will provide sufficient clearance for fitment of
any cab mounted roof accessories
Ladder access from deck surface to cab guard shall be
provided with grip strut type steps and two handles
Specify
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Comply
Yes
No
Yes
No
AERIAL DEVICE
Unit to be stacked boom design with knuckle at front and Make:
bucket at the rear. Aerial device should be positioned far
enough ahead to allow easy entry to the bucket from rear
deck of body.
Model:
This unit must conform to C.S.A. Standard C225-M88 (or
latest revision) for Vehicle Mounted Aerial Devices.
FT14
Vehicle Minimum Specifications
Tender’s Specifications
Ground to bottom of platform height 69ft minimum
Working height 74ft minimum
Vertical elevator height 10 ft minimum elevator mounted
parallel to chassis frame is preferred to provide maximum
use of space for body and lower platform.
Reach from centreline of rotation to lip of platform 49 ft
minimum
Reach with lower boom at 125 degrees 45 ft minimum
Platform dimensions 24”x 24” x 39” moulded fibre glass one
man side mounted fixed mounted
Platform capacity 350lbs
Unit to have mechanical levelling system which requires
limited maintenance
Aerial rotation 360 degrees continuous
Upper boom – filament wound round with 10” minimum
inside diameter contains Insulated conduit for routing of
hydraulic lines and fully contains upper boom levelling
system
Lower boom to fabricated of 12” square diameter x .25” wall
steeling as a minimum filament wound fibre glass is 11”
square outside X .625 wall thickness, located in the lower
the boom and provides 15 inch minimum of clear insulation
gap
Upper boom articulation 0 to 270 degrees
Lower boom articulation 0 to 125 degrees
Specify
Specify
Specify
Specify
Yes
No
Specify
Yes
No
Yes
Specify
Specify
Yes
Yes
OUTRIGGERS
Outriggers to be “A” frame with swivel shoes and hardwood Yes
pads
Unit must have interlock system that requires that
Yes
outriggers be set in place before aerial device can be
operated
Unit to have motion alarm to provide audible signal that the Yes
outriggers are in motion
HYDRAULIC SYSTEM
Hydraulic System to be a an open-centre which has the
following minimum requirements:
• Operates at 6.5 gpm @ 3100 psi
• 25 gallon reservoir with suction strainer
• a return line filter 10 micron
• magnetic drain plug
• Clear sight line sight gauge
• breather cap
• shutoff valves
FT15
No
Specify
No
No
No
No
No
Vehicle Minimum Specifications
Tender’s Specifications
ACCESSORIES
A waterproof cover shall be provided for the bucket
A safety ring to anchor the operator's safety belt.
Supply one spare bucket complete
ACCESSORIES cont’d
Unit to be equipped with Grey Island Interfleet GPS tracking
service operating on the Roger s cellular network Note:
System to installed at the City of Guelph Operations yard 45
Municipal Street Guelph
CPL automatic greasing system
Veilig LCD colour two camera package model RDCV7LCDS with 7” LCD monitor , two colour cameras with 130
degree viewing with low lighting LED, 20M video harness
and standard mounting hardware. Mounting position to be
discussed at pre-build meeting
PAINT
The truck cab and shall be O.E.M. bright white
ELECTRICAL CERTIFICATION
The completed aerial device shall be tested electrically in
compliance with the provisions of C.S.A. C225for use up to
49 KV, and a test certificate.
C.S.A. CERTIFICATION
The completed vehicle shall comply with the latest revisions
of the CAN/C.S.A. C225-M88 standard for vehicle mounted
aerial devises
PRE-BUILD MEETING
Winning vendor must a mandatory pre-build meet with City
staff to review and clarify build specifications with 3 weeks
of issue of Purchase Order
Yes
Yes
No
No
Yes
No
Yes
No
Specify
Specify
Specify
Yes
WARRANTY
Full three (3) year warranty on chassis and engine and a
Specify
five (5) year warranty on transmission, warranty will become
effective on the in-service date not the delivery date
FT16
No
Vehicle Minimum Specifications
Tender’s Specifications
MODEL
Unit shall be current model of a reputable manufacturer
Make: ____________________
Model: ____________________
The truck to be equipped with a construction dump box
Yes
Shop repair manuals, operator's manual, and spare parts manuals
must be included at time of delivery. Manuals can be provided on
CD or DVD as well as hard copies
No
VEHICLE WEIGHT
G.V.W. 18,598 kg (41,000 lbs.) minimum
Specify
ENGINE
4 Stroke, turbo charged - diesel
Engine gross H.P. - 250 h.p.,
Engine net torque 800 Lb/ft. minimum at rated R.P.M.
Engine fuel system to be equipped with a manual fuel primer
Specify
Specify
Specify
Yes
No
Yes
No
Specify
Yes
No
ENGINE EQUIPMENT
Air cleaner, heavy duty dry type with dash mounted air restriction
gauge
Antifreeze to -35°C. Long Life
Horton air operated engine cooling fan
Alternator -160 amp. minimum
Batteries - 12 Volt maintenance free, total capacity shall be 1900
CCA minimum SAE rated
Exhaust system shall be a single horizontal muffler and vertical
stack with curved spout passenger side discharge, muffler to be
mounted above chassis frame
Fuel/water separator, heavy duty with sight glass
Engine block heater. 110V - 1500W
Cold starting aid or Intake pre-heater
Engine Protection Alarm system shall have bell or buzzer and
warning light for the following limits: High coolant temperature, low
oil pressure, high trans temperature
Cruise control and PTO High idle control switch. Road speed to be
set at maximum 105/ kilometres per hour.
Engine coolant filter, spin on, universal charge
Specify
Specify
Yes
Yes
Yes
Specify
No
No
No
Yes
No
Yes
No
TRANSMISSION
Allison 3500 RDS 5 speed automatic with third gear hold (Scan to Yes
No
FT17
be provided by winning bid)
Transmission shifter shall be a dash mounted electronically
operated shifter
Yes
Transmission cooler
Yes
No
No
FRONT AXLE
Axle capacity 7,257 KG (18,000 LB) minimum.
Power steering with oil cooler for power steering fluid
Front shock absorbers
Grease-able tie rod ends, drag link
Oil bath front wheel seals and caps.
No
No
No
No
REAR AXLE
Rear axle capacity 10,430 KG(23,000 LB) minimum
Rear spring capacity 13,608 KG (31,000 Lb) minimum
Inter-wheel differential lock with in cab control
Rear axle ratio to be provide for approximately 100 km/hr max road
speed at rated engine RPM
BRAKES
Full air with ABS -Cam operated -Front 16.5 x 6”- Rear 16.5 x 7”
Automatic Slack adjusters front and rear Haldex required
Air Compressor 16.5 preferred
Air Dryer – 480-024 Haldex Pure Air Plus with electric heater
Air supply port for shop air/glad hand for towing
Air tank drain valves with cables mounted near the driver’s
access steps
Spring applied parking brake chambers
Push rod protection boots and stroke indicators
Manual air tanks drain valves easily accessed by pull cord from
drivers side of vehicle
FRAME
Full depth frame front to rear
Double frame from rear spring shackle to front spring shackle
RBM minimum 3,000,000 in lbs
Specify
Yes
Yes
Yes
Yes
Specify
Specify
Yes
Specify
Yes
Yes
Specify
Specify
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
CHASSIS
Set back front axle
Yes
Wheelbase, 168" maximum
Specify
Cab to axle 102" maximum
Specify
Aluminium fuel tank 265 Litre capacity minimum, complete with Specify
gauge.
RH and LH cab access steps
Yes
Two front tow hooks
Yes
CAB
FT18
No
No
No
No
No
No
Conventional cab
Engine hood shall be tilt type with engine compartment splash
Dual air horns with covers
Windshield wipers–dual electric 2-speed intermittent feature and
electrical washer pump
Power, adjustable, heated 8x16 west coast mirrors with swing away
brackets on both sides
Grab bar on each side of the cab to assist entry to the cab
Two, fender mounted, 100 mm (4") diameter, amber directional
lights facing front.
Interior dome light
Rear stop lights, signal lights and four-way flashers
Five streamline cab marker lights
Back-up alarm.
Tail and signal lights shall be LED.
Front bumper - painted
Rubber floor mat with foam backing
Both seats to be air suspended high back with head rest, dual arm
rest, National “2000” or equivalent
Power windows- both sides
Sunvisor - 2, interior
OEM standard gauge package
Yes
No
Yes
No
Specify gauges:
Automatic transmission temperature gauge.
Tachometer
AM/FM stereo with dual speakers
Tinted glass on all windows
R134A Air conditioning & cab pressurization
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
Specify
No
WHEELS AND TIRES
Pilot or Hub mounted steel wheels front and rear
Tire size and type of tread, front, shall be Michelin XZY-3
385/65RX22.5
Tire size and type of tread, rear, shall be Michelin XDE M/S
11R22.5
Rim size shall be 22.5 X 8.25DC and have a load capacity and
pressure rating equal to or exceeding that of the tires
Yes
Yes
Yes
Yes
No
No
No
No
Yes
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Specify
No
No
No
No
No
No
No
Specify
Specify
MUDFLAPS & SPLASH GUARDS
Mud flaps to be supplied and installed in front and behind ear Yes
wheels and splash guards installed in front to stop road splash on
side windows and mirrors
TOWING
FT19
No
One rear frame mounted pintle hook(Holland PH30RP41 2000 lb. Specify
vertical weight and 10,000 lb. pull weight adjustable from 12” min to
18” maximum eye height with safety chains
6 terminal split plug
Yes
HYDRAULIC SYSTEM
Hydraulic pump to be transmission mounted “hotshift” PTO type,
capable of driving all hydraulic functions simultaneously
Sight glass in Hydraulic tank
Two shut off valves to be installed at inlet and outlet of filters
A high pressure filter assembly will be installed on the pressure
side of the hydraulic system, complete with condition indicator
Low oil level warning device to be installed in hydraulic oil
reservoir, with in cab indicator light
SQUARE STEEL CONSTRUCTION DUMP BOX
General construction, square dump body, with continuous welded
fully braced sides. Box floor and sides to have non-stick plastic
liner to prevent material sticking in box. The box shall also be
equipped with a vibrator unit for box floor.
Please state make and model
The capacity of the box shall be approximately 8.5 cubic yards and
approximately 10 cubic yards with 10” hardwood side boards
Body to made of minimum 10 gauge steel
Floor to be made of 3/16” mild steel
Cross-members shall be 3” x 1 3/8” structural channel and built on
12” centres
Separate body and hoist frame will be provided, direct push on
frame not acceptable
Tipping angle shall be 50 degrees to 55 degrees
Double acting square tailgate with safety chains
Tailgate latching system shall be operated by double acting air
cylinders. Cylinders to be activated by in cab electrical switch or
pneumatic valve.
Body hinge to be above the chassis frame
Air operated tarp system with 2 outboard cylinders and in cab
control switch
Specify
Yes
Yes
Yes
No
No
No
Yes
No
Make
Model
Specify
Specify
Specify
Specify
Yes
No
Yes
Yes
No
No
Yes
Specify
No
Unit to have completely sealed Grote LED lighting system with Yes
corrosion proof junction boxes and lamps and Ultra Blue Seal wiring
harness
Box mounted Preco strobe light model #4261 mounted on top of Yes
front edge of dump box
Star Strobe lighting kit 3300 star pack with four amber oval lights
mounted in rear of box
Clearance lights to wired into the chassis marker lights
Yes
FT20
No
No
No
No
Pipe protected tail and directional lights in rear corner posts
Front mounted hoist – 3 stage telescopic suitable for box capacity
Safety support capable of holding box in lifted position while
servicing truck chassis and hoist
Painting - Body shall be properly prepared or painting by
sandblasting and applying rust prevention coating and/or primer and
the box painted grey with Imron 5000 with bake on finish
Primer shall be zinc base rust inhibitive type
Yes
Yes
Yes
No
No
No
Specify
COLOUR
The truck shall be painted OEM bright white as approved by Fleet Specify
Manager
LICENSE
Unit will be delivered fully licensed valid until March 31st 2010 with Yes
RGW set to manufacturers Gross Combined Weight Rating
WARRANTY
Chassis- one year minimum
Engine- Three year minimum
Transmission- Five year minimum
Dump box- one year minimum
No
Specify
Specify
Specify
Specify
GREASING SYSTEM
CPL Grease System to be installed to supply all chassis and body Yes
grease points
No
GPS SYSTEM
Unit will be equipped with Grey Island Interfleet GPS tracking Yes
services operating on the Rogers cellular network
No
FT21
Minimum Specifications
Tender’s Specifications
MODEL
Units to be 60,000 lbs chassis with 20,000 lbs front
axles and 40,000lbs rear axles suitable for use by
City of Guelph Operations Department for Winter
Control activities and for dump truck construction
work in the summer months. These trucks will be
outfitted with front plough and harness, plough wing
and a square steel construction dump body. The
front of truck will need to accommodate a front
mount variable displacement piston pump
crankshaft driven with PTO retractable shaft for fan
belt replacement without pump or PTO removal.
The unit shall be a current model of a reputable
Manufacturer
Make
Model
Shop repair manual, and wiring diagrams, driveability
and emissions manual, operators manuals and spare
parts manual must be included at time of delivery
Yes
VEHICLE WEIGHT
60,000 lbs GVW minimum
Specify
WHEEL BASE
Approximately 180 inches
Cab to Axle approximately108 inches
Specify
Specify
AXLES & DIFFERENTIAL
Front 20,000 lbs
Rear 40,000 lbs
Oil type hubs – front axle
Set back front axle
Rear tandem axles with full locking main axle with diff
lock controlled by switch in cab
Rear axle ratio to be provide for approximately 100
km/hr max. road speed at rated engine RPM
FRAME
Frame to be minimum RBM of 3,000,000 lbs/inch per
rail
Front "C" Channel insert required provision to be
made to prevent "diamond shaping" of frame. The
frame shall be bridged or a cross member supplied
within 10 inches of the rear of the cab in order to
transmit the plow wing "push" to each frame rail.
This crossing shall be fore and aft at each end.
FT22
Yes
Yes
Yes
Yes
Yes
Specify
Specify
Specify
No
No
No
No
No
No
Minimum Specifications
Tender’s Specifications
Frame height from top of rails to ground
approximately 44”
ENGINE
300 hp minimum turbo charged diesel engine with
electronically controlled fuel injection and engine
management system
Full RPM 2600
Peak torque 860 ft/lbs
Specify
Specify
Specify
Specify
Horton air operated engine cooling fan
COOLING SYSTEM
Heavy duty rad core
Specify
Antifreeze to -35ºC Long life
Corrosion resistant spin on coolant filter with shut –off
tap
TRANSMISSION
Automatic Allison 3500 RDS 5 Speed electronic with
third gear hold
External transmission cooler
Allison Transmission SCAN to be provide by
Successful bidder
Transmission must have synthetic fluid
SUSPENSION
Heavy duty gas shock absorbers required all axles
Front axles to spring type suspension with rubber
block helper spring on curb side of truck
Rear Suspension Hendrickson RT 403
TIRES/WHEELS
Rear tires XDE M/S 11R22.5
Steer tires XYZ-425/65R-22.5
Heavy duty, steel disc pilot hubs front & rear
Spare and Rim for each truck
STEERING
Integral power steering of sufficient capacity for
18,000 lb axle
Turning radius
FT23
Yes
Yes
No
No
Specify
Yes
Yes
No
No
Yes
No
Yes
Yes
No
No
Yes
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
No
Specify
Minimum Specifications
Tender’s Specifications
BRAKES
Full air with ABS
S-cam operated
Automatic slack adjustors front & rear – Haldex
required – with stroke indicator at all wheels
Anchor type 30 chambers with life seal
Air compressor 16.6 CFM minimum
Automatic front brake limiting valve
Backing plates- all wheels
Air tank drain cables mounted near the driver’s
access steps
Air drier -480-024 Haldex pure air plus with electric
heater
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
No
Yes
Specify
No
Yes
Specify
Yes
No
ELECTRICAL
2 -12 volts maintenance free batteries
Combined CCA of 1900
130 amp alternator minimum
Stop/ tail / turn marker & indicator lights to be LED
All lights in accordance with Highway Traffic Act
Yes
Specify
Specify
Yes
Specify
No
Backup alarm 90 db. minimum
Circuit breaker to be supplied in lieu of fuses
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
No
FUEL SYSTEM
Heavy duty fuel water separator
Aluminum fuel tank with steps( 2 required) mounted
on driver’s side of vehicle – minimum capacity 265
litres / 70 imperial gallons
EXHAUST
Passenger side mounted
Exhaust system must not interfere with the plow,
Muffler to be mounted above chassis frame rail height
to prevent exposure to road salt
CAB/BODY
Conventional Cab
Stationary front grill with tilt hood.
Floor vents
15% tinted front window
Full ventilation and cab pressurization system with
R134a air conditioning
Low mounted window in passenger door
FT24
No
No
Minimum Specifications
Tender’s Specifications
INTERIOR
Full black rubber floor cover
Two (2) bostorm or approved equivalent fully padded
cloth air ride seats with fully adjustable head rest, arm
rest left & right side of each seat
Gray fabric with stain protection (Scotchguard)
ACCESSORIES
Intermittent wipers
Driver & passenger side air bag
Am/Fm radio with clock CD player
Dual sun visors
Dual air horns with covers
Power adjustable heated, 8x16 west coast mirrors
with swing away brackets (both sides)
Power windows (both sides)
Cup holders
1500 watt block heater
CPL automatic greasing system
High temperature & low oil audible warning system
Unit will be equipped with Grey Island Interfleet GPS
tracking services operating on the Rogers cellular
network. Note: System to be installed at Works Yard
45 Municipal Street Guelph
INSTRUMENTATION
Engine oil temperature
Fuel gauge
Oil pressure gauge
Engine hour meter
Engine tach
Transmission temperature gauge
Air restriction gauge mounted in the dash
COLOUR
Unit shall be painted OEM Bright White as approved
by the Fleet Manager
LICENSING
Unit to be licensed to full GVWR for 12 months
WARRANTY
Full 3 year warranty required on chassis & engine, 5
year warranty on Transmission, warranty will become
effective on the in-service date not the delivery date.
FT25
Yes
Yes
No
No
Yes
No
Yes
Yes
Specify
Specify
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
Specify
Specify
Specify
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement