Shure PSM200 Wireless User Guide English - Bax-shop

Shure PSM200 Wireless User Guide English - Bax-shop
Model PSM200 User Guide
PSM 200
Personal Monitor System User Guide
>>E2
2005, Shure Incorporated
27B8792 (Rev. 3)
>>P2R
>>P2T
Printed in U.S.A.
ENGLISH
WARNING!
USING THIS SYSTEM AT EXCESSIVE VOLUMES CAN CAUSE
PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE.
In order to use this system safely, avoid prolonged listening at excessive sound pressure levels. Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure
to sound pressure levels before hearing damage occurs.
90 dB SPL at 8 hours
95 dB SPL at 4 hours
100 dB SPL at 2 hours
105 dB SPL at 1 hour
110 dB SPL at 1/2 hour
115 dB SPL at 15 minutes
120 dB SPL — avoid or hearing damage may occur
It is difficult to measure the exact Sound Pressure Levels (SPL) present at the eardrum in live applications. In addition to
the volume setting on the PSM, the SPL in the ear is affected by ambient sound from floor wedges or other devices. The
isolation provided by the fit of quality earphones is also an important factor in determining the SPL in the ear.
Here are some general tips to follow in the use of this product to protect your ears from damage:
1. Turn up the volume control only far enough to hear properly.
2. Ringing in the ears may indicate that the gain levels are too high. Try lowering the gain levels.
3. Have your ears checked by an audiologist on a regular basis. If you experience wax buildup in your ears, stop
using the system until an audiologist has examined your ears.
4. Wipe the earphones with an antiseptic before and after use to avoid infections. Stop using the earphones if
they are causing great discomfort or infection.
This symbol indicates important operating and
maintenance instructions in the literature accompanying this unit.
LICENSING INFORMATION
THIS RADIO EQUIPMENT IS INTENDED FOR USE IN PROFESSIONAL ENTERTAINMENT AND SIMILAR APPLICATIONS.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless
microphone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure
strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.
NOTE: THIS EQUIPMENT MAY BE CAPABLE OF OPERATING ON SOME FREQUENCIES NOT AUTHORIZED IN YOUR REGION. PLEASE CONTACT YOUR NATIONAL AUTHORITY TO OBTAIN INFORMATION ON AUTHORIZED FREQUENCIES FOR WIRELESS MICROPHONE PRODUCTS IN YOUR REGION
Licensing: Note that a ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible
requirements.
1
ENGLISH
TABLE OF CONTENTS
QUICK SET-UP GUIDES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
PSM200 Wireless System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
P2R Receiver Quick Set-Up Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
The PSM200 Personal Monitor System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
THE P2T TRANSMIXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phantom Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a Frequency Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
6
6
P2R RECEIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Controls and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Management Groove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wired Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIX IN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIM LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
8
8
8
8
8
SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wireless System Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hybrid Wired/Wireless System Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
P2R Stand-Alone Wired Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SYSTEM APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
APPLICATION ONE: Wireless Set-Up for a Vocalist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
APPLICATION TWO: Combination Wired and Wireless Set-Up for a Drummer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
APPLICATION THREE: Two PSM200 Wireless Systems Used Simultaneously . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RACK MOUNTING THE P2T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2T TransMixer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2R Receiver Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PSM200 Channel Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
13
13
CERTIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
P2R Receiver MIX IN Jack Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2
ENGLISH
QUICK SET-UP GUIDES
PSMR200 Wireless System
The following set-up illustration is for the complete PSM200 Wireless System, which includes the P2T TransMixer,
the P2R Receiver, and the E2 Earphones. If you have purchased the P2R as a stand-alone wired personal monitor,
see page 4.
1.
Plug in the power supply and connect it to the DC
input on the rear panel of the P2T TransMixer.
2.
Insert a 9 Volt battery into the P2R Receiver,
observing proper polarity.
PSM200 TransMixer
MIC/LINE
1
1
MIC/LINE
2
INPUTS
2
CHANNEL
SELECT
Mixing Console
3.
Connect audio sources to the MIC/LINE INPUTS on the front
panel of the TransMixer.
6.
Check the RF LED on the top of the Receiver to
confirm that it is receiving signal from the TransMixer.
4.
Turn the Receiver volume knob clockwise past the click (ON).
Keep the volume at a low setting.
7.
Plug the Earphones into the earphone jack on the
Receiver. Insert the Earphones into your ears.
5.
Set the TransMixer and Receiver to the same frequency channel. See the Selecting a Frequency Channel section on page 6.
8.
Increase Receiver volume until the knob is turned to
approximately 11 o’clock.
PSM200 TransMixer
MIC/LINE
1
MIC/LINE
2
1
INPUTS
2
CHANNEL
SELECT
Mixing Console
9.
On the front panel of the TransMixer, adjust the signal level of each audio input with the INPUT knobs.
10. Check the INPUT LEDs on the TransMixer to verify that signal is present, but not clipping. See the Audio Inputs
and Outputs section on page 6 for details.
11. Slowly adjust the Receiver volume to a comfortable level.
3
ENGLISH
P2R Receiver Quick Set-Up Guide:
When Used as a Wired Stand-Alone Personal Monitor
Mixing Console
1.
Insert a 9 Volt battery into the P2R Receiver,
observing proper polarity.
2.
Connect an audio source to the 1/4-inch MIX IN jack
on the side of the P2R.
3.
Turn the P2R volume knob on (past the click).
Keep the volume at a low setting.
4.
Set the CHANNEL to “A” with the SELECT Button.
See the Wired Mode section on page 8 for details.
5.
Set the GAIN switch to LO initially and set
your source volume to a moderate level.
6.
Attach the P2R onto your belt, waistband, or another
location and slide the cable into the cable management
groove on the back side of the unit.
7.
Plug Earphones into the earphone jack on the P2R.
Insert the Earphones into your ears.
8.
Slowly adjust the volume to a comfortable level. Set
the GAIN switch to HIGH if the signal level is too low.
Mixing Console
4
ENGLISH
INTRODUCTION
Thank you for buying the PSM200. Like all Shure PSM personal monitoring products, the PSM200 provides the many advantages of
in-ear monitoring including:
Improved Sound Quality —high fidelity without the risk of feedback,
Increased Mobility —your mix moves with you,
Personal Control —create a personal mix, and control your own levels.
For information on this and other Shure products, visit www.shure.com on the World Wide Web.
The PSM200 Personal Monitor System
crophones or instruments directly to the inputs, use line outputs from a mixing console, or connect it to Shure’s AuxPander. In short, no matter what the output device, you
can probably plug it into the TransMixer.
The PSM200 is a frequency-agile, in-ear monitor system for
use in a wide variety of applications. Its many features help
overcome the difficulties associated with stage monitoring.
The P2R Receiver is the world’s first bodypack receiver to
function as a wired receiver, a wireless receiver, or both at
the same time. This and other unique features, along with
excellent sound quality, make the P2R an exceptional value.
The complete PSM200 System includes the E2 Earphones,
which feature a dynamic driver that produces crisp, full-spectrum sound. They include a variety of sleeve options to provide
the best fit and isolation for your ears. The E2, like all Shure
earphones, work well with CD players, MP3 players, and anything else with a 1/8-inch (3.5mm) stereo output.
The P2T TransMixer is another breakthrough design for
in-ear monitoring. It allows the user to connect two line-level
or mic–level inputs directly into the transmitter. The two signals can then be mixed independently. You can connect mi-
Features
PSM200 System
8 selectable UHF frequencies
Includes E2 dynamic-driver earphones
Mono mix
Input level controls
1/ -inch line-level input jack to connect monitor mix, click
4
tracks, effects, or condenser microphones
Integrated cable management groove secures cables connected to the bodypack
Up to 4 systems can be operated simultaneously
P2T TransMixer
2 mic/line XLR/ 1/4 -inch combo inputs
XLR SPLIT OUT connectors
Tri-color LED input level indicators
P2R Receiver
Combination wired/wireless compatibility
Gain switch for setting line input sensitivity
5
ENGLISH
THE P2T TRANSMIXER
Controls and Features
1
2
4
5
FRONT PANEL:
6
3
BACK PANEL:
7
1.
2.
3.
4.
9
8
MIC/LINE INPUT Jacks: Electronically balanced inputs
that accommodate both XLR and 1/4-inch connectors at
mic or line levels.
Signal/Clip LEDs: Color indicates the signal status of the
corresponding MIC/LINE input, as explained in the Audio
Inputs and Outputs section below.
INPUT Knobs: Control the level of their corresponding
inputs.
CHANNEL LED Indicator: Displays the frequency channel that is being transmitted (1-8).
5.
6.
7.
8.
9.
SELECT Button: Press to select a frequency channel.
Antenna: Permanently mounted, break–resistant antenna transmits the mix to the P2R Receiver.
Power Cord Strain Relief: Thread the power cable
through these slots to secure the DC connection.
DC IN: Plug the power supply into this connector. The unit
remains powered on until you unplug it.
SPLIT OUTs: Each male XLR output jack duplicates the
signal of the corresponding mic/line input. Front panel settings have no effect on split output level.
Audio Inputs and Outputs
The INPUT knobs control both MIC and LINE level signals. As a general guideline, set the knob to the left of twelve o’clock for line level signals, and to the right
of twelve o’clock for microphone levels.
Observe the signal/clip LEDs. If they are consistently red, decrease the level
with the corresponding INPUT knob.
INPUT LED
RED — Limited Signal*
YELLOW — Nominal Level
GREEN — Signal Present
NOTE: If the level is decreased all the way and the LED
Microphone
Line
remains red, the level of the input from the previous device
Level
Level
in the audio chain (mixer, click track, digital sequencer, etc.)
INPUT Knob
is too high and should be decreased.
To pass audio signal directly through the TransMixer, use the corresponding SPLIT OUT on the rear panel of the device. Input settings
do not affect the level of the signal at the SPLIT OUT connectors.
* The P2T inputs have limiting circuitry that activates automatically when the input level is too high.
Phantom Power
Although the TransMixer itself does not provide phantom power for condenser microphones, the SPLIT OUT connectors pass phantom power from a phantom power supply to a microphone connected to the corresponding input jack. You can connect equipment that supplies phantom power to the TransMixer without harming the unit.
CAUTION!: Use a “direct box” when connecting guitars, keyboards, and other instruments to a mixing console through the P2T.
The phantom power that mixing consoles provide for microphones can damage other instruments. Connect the instrument to the
direct box then connect the direct box to the TransMixer input.
Selecting a Frequency Channel
1.
Press and hold the SELECT button until the CHANNEL LED indicator begins to flash.
2.
When the LED indicator is flashing, press the SELECT button to scroll to the desired frequency channel.
3.
Release the button. After 4 seconds the display will stop flashing and the P2T will automatically switch to the
specified channel.
IMPORTANT:
Never set more than ONE TransMixer to the same frequency channel, or interference will occur.
6
ENGLISH
P2R RECEIVER
Controls and Features
12
11
2
1
3
7
4
5
8
9
10
6
13
1.
POWER LED: Lights to indicate the unit is powered on
and blinks to indicate low battery. When this LED
starts blinking, you have approximately 15 minutes of
battery time remaining, depending on volume level
and battery brand.
2.
On/Off/Volume Knob: Turn clockwise past click to
power on. Continue to turn clockwise to increase volume, counterclockwise to decrease volume.
3.
LIM LED: Lights only when limiter is activated. See the
LIM LED section on page 8 for details.
4.
RF LED: Lights when the unit is receiving radio frequency
(RF) signal from the P2T TransMixer.
5.
Antenna: An attached, flexible whip antenna receives RF
signal from the TransMixer.
6.
CHANNEL LED Indicator: Displays the number of the
current frequency channel (1-8), or the letter “A” for
wired mode. The CHANNEL LED indicator shuts itself
off after 10 seconds to conserve battery life. To view the
Battery Installation*
1.
2.
3.
7.
8.
9.
10.
11.
12.
13.
frequency channel when the LED indicator is off, simply
press and release the SELECT button.
SELECT Button: Press to increment the frequency
channel or set to “A” for wired mode.
MIX IN Jack: Connect a 1/4-inch line-level input to this
jack. Use alone, or in combination with wireless reception from the P2T TransMixer. See the MIX IN Jack
section on page 8 for details.
GAIN Switch: Slide to HI or LO position to set the sensitivity of the MIX IN input.
Earphone Output Jack: Connect E1, E2, or E5 earphones to this 1/8-inch (3.5mm) jack.
Cable Management Groove: For a secure connection,
guide the cable connected to the MIX IN Jack or the
earphone cord into this groove.
Belt Clip: Securely attaches the unit to a belt, guitar
strap or waist band.
Battery Compartment Door: See the Battery Installation section below.
Unlock the battery compartment door by pressing down
on the side of the battery compartment door marked
“OPEN” and sliding it in the direction of the arrow.
Flip open the door and insert a fresh 9V alkaline battery,
observing proper polarity.
Flip the battery compartment door closed, then press
and slide the compartment door until it snaps shut.
Note: If the battery compartment door will not close
completely, the battery is not correctly inserted.
* Since the average life of a battery varies depending on the manufacturer, Shure recommends that you
use a fresh 9V battery for performances longer than two hours. You can then reserve used batteries for
rehearsals or other less critical applications.
Cable Management Groove
1.
2.
3.
4.
Connect an audio source to the 1/4-inch MIX IN jack on the side of the P2R.
Attach the P2R to your belt, waist band, or another location.
Slide the audio cable or earphone cord up into the groove, as illustrated.
The belt clip will hold them securely in place.
7
ENGLISH
Wireless Mode
When you are using the P2R as a wireless receiver, or as a combination wired and wireless receiver, use the SELECT button on
the side of the P2R Receiver to set the frequency channel (1-8).
To Select a Frequency Channel:
1.
2.
3.
Press and hold the SELECT button until the CHANNEL LED indicator begins to flash.
When the LED indicator is flashing, press the SELECT button to scroll to the desired
frequency channel.
Release the button. After 4 seconds the display will stop flashing and the P2R
will automatically switch to the specified channel.
NOTE: Set the P2R to the same channel as the P2T TransMixer.
Wired Mode
When you are using the P2R Receiver as a stand-alone wired monitor, you can set the unit
to wired mode. This deactivates the RF circuitry and extends the battery life.
To Set the P2R to Wired Mode:
1.
2.
3.
Press and hold the SELECT button until the CHANNEL LED indicator begins to flash.
When the LED indicator is flashing, press the SELECT button to scroll past channel 8 until the letter “A” appears in
the display.
Release the button. After 4 seconds the display will stop flashing and the P2R will automatically switch to wired mode.
NOTE: Setting the P2R receiver to wired mode disables its wireless capability.
Scanner Mode
When you are using the P2R as a wireless receiver, Shure recommends that during set–up you first scan for a frequency
channel that is free from interference:
1. Unplug the P2T TransMixer and turn off the P2R.
2. Hold down the P2R SELECT button while turning its volume knob past the click (ON).
3. Insert the earphones into your ears and slowly increase the P2R volume until you hear noise. The CHANNEL LED will
blink to confirm the unit is in Scanner Mode.
WARNING: Increase the volume slowly, as the noise may be loud.
4.
5.
6.
Scroll through the eight available frequencies to locate a clear channel. A channel is clear if you hear uninterrupted white
noise from the P2R. Avoid channels that have no sound. This indicates interference on that frequency channel, which
makes it unsuitable for use.
To exit scanner mode, simply turn off the P2R. When you turn the unit back on it will be set to the channel that you
last selected.
Set the P2T to the same channel as the P2R.
MIX IN Jack
When you are using the P2R Receiver as a stand-alone personal monitor, the 1/4-inch MIX IN jack
serves as the primary audio input. In addition, the MIX IN jack allows the P2R to function as a hybrid
wired and wireless receiver. When you are using the P2R in its wireless mode, you can add a second
audio source via the MIX IN jack, such as.
Click Tracks
Pre-Amp Outputs from Guitar or Bass
Effects Processors
Condenser Microphones
Next to the jack is a two-position GAIN switch that gives you a choice between LO and HI gain settings
for the input. For specific information on how the MIX IN jack functions, refer to the wiring diagram on
page 14.
LIM LED
The P2R Receiver has a non–defeatable (constantly active) limiter that automatically activates
if the receiver output level exceeds a certain volume, which is calibrated specifically for the
Shure E2 earphones. The LIM LED on the top of the unit lights up when the limiter is on. If the
LIM LED blinks occasionally, turn down the volume of the receiver.* If the LED is on and you
haven’t reached a high enough listening level, try re-inserting the earphones for a better seal,
or adjust the mix that is being sent to the receiver to include only the most essential inputs.**
* When the LED is on, the volume will not increase.
8
** The limiter is designed to work best with the Shure E2 earphones.
Using the P2R with Shure E1 or E5, or earphones made by other
manufacturers, can result in higher limited volume levels.
ENGLISH
SET-UP
Wireless System Set-Up
To configure the P2T TransMixer and P2R Receiver for wireless operation:
5.
1. Plug the power supply into the DC INPUT connector on the
rear panel of the P2T, then plug it into a power outlet.
2. Connect audio sources to the combo XLR/1/4-inch jacks on
the front panel.
6.
3. Select a frequency channel (1-8). See the Selecting a Frequency Channel section on page 6 for details.
7.
IMPORTANT: Never set more than ONE
8.
TransMixer to the same frequency channel, or
interference will occur.
9.
4. Observe the signal/clip LEDs. If they are consistently
red, decrease the level with the corresponding INPUT
level knob.
10.
To pass audio signal directly through the TransMixer, use
the corresponding SPLIT OUT connector on the rear panel
of the device.
Turn the On/Off/Volume knob on the P2R clockwise past click
(On). Leave the volume setting low.
Set the P2R to the same frequency channel as the P2T.
Check the RF LED on the P2R to confirm that transmission
is being received.
Plug earphones into the earphone output jack. Insert the
earphones into your ears as instructed in the earphone
user’s guide.
Slowly increase the P2R volume to a comfortable level.
PSM200 TransMixer
MIC/LINE
1
MIC/LINE
2
1
INPUTS
2
CHANNEL
SELECT
Mixing Console
Hybrid Wired/Wireless System Set-Up
To configure the P2T TransMixer and P2R Receiver for hybrid wired/wireless operation:
4. Attach the P2R onto your belt, waistband, or another location.
1. Follow steps 1-9 of the Wireless System Set-Up section.
5. Slide the audio cable or earphone cord into the cable man2. Connect an audio source to the 1/4-inch MIX IN jack on
agement groove.
the side of the P2R.
6. Slowly increase the P2R volume to a comfortable level. Set
3. Set the GAIN switch to LO initially and set the source
the GAIN switch to HI if you need more level.
volume to a moderate level.
P2R Stand-Alone Wired Set-Up*
To configure the P2R Receiver as a stand-alone personal monitor:
1. Turn the On/Off/Volume knob clockwise past click (On).
Leave the volume setting low.
2. Set the CHANNEL to “A” with the SELECT Button. See the
Wired Mode section on page 8 for details.
3. Connect an audio source to the 1/4-inch MIX IN jack on
the side of the P2R.
4. Set the GAIN switch to LO initially and set the source
volume to a moderate level.
5. Attach the P2R onto your belt, waistband, or another
location.
6. Slide the audio cable or earphone cord into the cable
management groove.
7. Plug the earphones into the earphone output jack. Insert
the earphones into your ears as instructed in the earphone user’s guide.
8. Slowly increase the P2R volume to a comfortable level.
Set the GAIN switch to HI if you need more level.
Mixing Console
NOTE: Setting the P2R receiver to “A” disables its wireless capability and extends the battery life.
* If you have purchased the P2R as a stand-alone personal monitor, you can go wireless by simply purchasing a
P2T TransMixer.
9
ENGLISH
SYSTEM APPLICATIONS
This section presents three typical applications for the PSM200. For more ideas, visit Shure’s website at www.shure.com.
APPLICATION ONE: Wireless Set-Up for a Vocalist
This is the basic wireless configuration of the PSM200 system for a single user, either instrumental or vocal:
1. Connect the vocal mic to INPUT 1 of the P2T TransMixer.
2. Connect SPLIT OUT 1 from the P2T to the Mixing Console.
3. Connect the instrumental mix line out to INPUT 2 of the P2T.
4. Set the P2T and P2R to the same frequency channel.
5. Insert the E2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer.
Wireless
Transmission
Vocal Mic Signal
SPLIT OUT
from TransMixer
Vocal Mic
Band Mix
Mixing Console
APPLICATION TWO: Combination Wired and Wireless Set-Up for a Drummer
The following application uses the P2R as a combination wired/wireless Receiver. The MIX IN jack of the P2R is connected
to a click track for the drummer:
1. Connect the drum mix out of the Mixing Console to INPUT 1 of the P2T TransMixer.
2. Connect the band mix out of the Mixing Console to INPUT 2 of the P2T.
3. Set the P2T and the P2R to the same frequency channel.
4. Insert the E2 earphones into your ears and adjust the mix of INPUT 1 and INPUT 2 on the TransMixer.
5. Set the P2R Receiver to a comfortable level.
6. Set the GAIN switch on the P2R to LO.
7. Connect the Click Output to the MIX IN 1/4-inch jack of the P2R and adjust your levels.
Band Mix
Drum Mix
Mixing Console
Click
Track
10
ENGLISH
APPLICATION THREE: Two PSM200 Wireless Systems Used Simultaneously*
The following configuration uses two PSM200 systems simultaneously, and utilizes the SPLIT OUT feature of the TransMixer. In this example, the musicians keep the TransMixers on stage with them, in order to control their personal mixes independent of the house engineer.
1.
Connect the vocal mic to INPUT 1 of the Vocal Mix TransMixer and connect SPLIT OUT 1 (the vocals) to the
Mixing Console.
2. Connect the total band mix from the Mixing Console to INPUT 2 of the Vocal Mix TransMixer.
NOTE: In this example, the band mix includes vocals. This allows the guitar mix to include vocals,
and allows the vocalist to independently control more of the vocal level in his/her personal mix.
3. Set the Vocal Mix P2T and P2R Receiver to the same frequency channel.
4. Connect SPLIT OUT 2 of the Vocal Mix TransMixer (the band mix) to INPUT 1 of the Guitar Mix TransMixer.
5. Connect the guitar amp simulator to INPUT 2 of the Guitar Mix P2T TransMixer.
6. Connect the SPLIT OUT 2 of the Guitar Mix TransMixer (the guitar amp simulator) to the Mixing Console.
7. Set the Guitar Mix P2T TransMixer and P2R Receiver to a frequency channel that’s different from the channel you
set for the Vocal Mix system in step 3.
* Up to four systems can be used at the same time.
Vocal Mic
SPLIT OUT
from
TransMixer
Vocal Mix
Band Mix
SPLIT OUT
from
TransMixer
Guitar Mix
Guitar Amp
Simulator
DIRECT BOX
Band Mix
Vocal
Mic
Vocal
Mix
Mixing Console
Guitar Amp
Simulator
SPLIT OUT
from
TransMixer
Guitar
Mix
RACK MOUNTING THE P2T
The P2T features a standard 1/2-rack space design, and includes a rack mounting kit.
WARNING: Do not torque the screws too tightly, or the chassis may be damaged.
Install Rack Ears
Dual-Mounting Two Units
Single Unit
PSM200
TransMixer
MIC/LINE
1
MIC/LINE
2
1
INPUTS2
PSM200
TransMixer
PSM200
TransMixer
SELECT
CHANNEL
MIC/LINE
1
MIC/LINE
2
1
INPUTS2
CHANNEL
SELECT
MIC/LINE
1
1
MIC/LINE
2
INPUTS2
SELECT
CHANNEL
Mount in an Equipment Rack
PSM200
TransMixer
MIC/LINE
1
MIC/LINE
2
1
INPUTS 2
PSM200
TransMixer
PSM200
TransMixer
MIC/LINE
1
CHANNEL
SELECT
MIC/LINE
2
1
INPUTS 2
SELECT
CHANNEL
MIC/LINE
1
MIC/LINE
2
1
INPUTS 2
SELECT
CHANNEL
NOTE: Be sure to use both straddle bars when installing dual units.
11
ENGLISH
TROUBLESHOOTING
PROBLEM
SOLUTION
No sound at the receiver
Check the power cord on the TransMixer and make sure it is
powered on.
Make sure both the TransMixer and the P2R Receiver are set to
the same frequency channel.
Make sure the earphones are plugged in to the receiver and the
volume is up.
Make sure the Receiver is on and the battery is good.
Check the incoming audio connections on the TransMixer.
Try to maintain line-of-sight between the TransMixer and Receiver
antennas.
Try another frequency in case interference is limiting the range.
Check for television channel interference. More information is
available at www.shure.com.
Make sure no other TransMixers or wireless transmitters are operating on your frequency.
Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure you are using a fresh battery in the P2R.
Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure the P2R Receiver’s volume knob is up.
Low receiver range
Receiver sounds fuzzy or distorted
Low audio output at the receiver
ACCESSORIES
Furnished Accessories
P2T TransMixer
AC Adaptor . . . . . . . . . . . . . . . . . . . . . PS20, PS20E, PS20UK
Single Mount Rack Bracket . . . . . . . . . . . . . . . . . . . . . 53A8484
Dual Mount Rack Bracket . . . . . . . . . . . . . . . . . . . . . . 53B8484
Straddle Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53A8443
Hardware Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90AD8100
P2R Receiver
1/4-inch mono 20 foot cable . . . . . . . . . . . . . . . . . . . 90B4677
Optional Equipment
AuxPander:
The Shure AuxPander auxiliary expander extends the capabilities of a standard mixing console by providing eight additional
auxiliary sends. It is designed ideally for use with multiple personal monitoring systems.
P4M:
The P4M is a highly versatile four–channel, two–bus stereo
mic/line mixer designed to optimize personal (in–ear) monitor
systems in live performance applications.
SPECIFICATIONS
PSM200 System
RF Carrier Frequency Range
518–865 MHz (country dependent)
Operating Range
100 m (300 ft.) under optimal conditions
Audio Frequency Response
30 Hz to 12 kHz (+/–3 dB); earphone dependent
Total Harmonic Distortion (1 kHz)
<1% typical (Ref. ±35 kHz deviation)
Modulation
FM ±35 kHz Deviation (Nominal)
Signal-to-Noise Ratio
80 dB typical (A-weighted)
Operating Temperature
–7° C to +49° C
(+20° F to +120° F)
P2T TransMixer
RF Output Power
30 mW (+15 dBm) typical conducted (country dependent)
Modulation Limiter
Internal peak limiter (>10:1 hard knee compression)
Antenna
1/4 Wavelength, semi-rigid, PCB Mount
Current
170 mA maximum
Dimensions
220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
Net Weight
370 g (13 oz.)
12
ENGLISH
P2T Audio Input
XLR/1/4-inch
Connector Type:
P2T Audio Outputs
Passive connection parallel with input.
combo
electronically balanced
Configuration:
Actual Impedance:
1 kΩ
Nominal Input Level:
–25 dBu @ 1/2 volume
(12 o’clock)
Maximum Input Level:
–5 dBu @ 1/2 volume
(12 o’clock)
Pin Assignments:
XLR: 2=hot; 3=cold, 1=ground
1/ : Tip = hot, Ring = cold,
4
Sleeve=ground
Phantom Power Protection?
Yes: Up to 52 Vdc
XLR
Configuration:
electronically balanced
Pin Assignments:
2 = hot ; 3 = cold, 1 = ground
Phantom Power Protection?
Yes: Up to 52 Vdc
Power Requirements
Operating voltage 12-18 Vdc
Supplied with one of the following external power supplies:
Model PS20: 120 VAC, 60 Hz input.
P2R Receiver
RF Sensitivity
–109 dBm typical
Model PS20E, Model PS20UK: 230 VAC, 50/60 Hz input.
Power Requirements
9 V alkaline battery, Duracell type MN1604 recommended
Battery Life
Volume Dependent
Squelch Threshold
–102 dBm typical
Antenna
Attached Whip
1/ -inch
4
Mono
Impedance:
1 MΩ
Maximum Input Level:
LO = +0 dBu
HI = –10 dBu
Frequency Response:
30 Hz to 20 kHz (+/–3 dB);
earphone dependent
Wired (RF Off):
6 hours
Wireless (RF On):
4 hours
Audio Output Connector
1/ inch (3.5 mm)
8
Minimum Load Impedance
8Ω
Net Weight
100 g (3.52 oz.), less battery
Overall Dimensions
122 mm x 73 mm x 32 mm
(4.809 in. x 2.875 in. x 1.251 in.)
Audio Input Connector
Connector Type:
Connector Type:
PSM200 Channel Frequencies
The PSM200 is available in four frequency groups, each coordinated to work in a specific geographic region. You can find the frequency
group for your system printed on the rear panel of the P2T TransMixer. For more information on which frequencies can be used in your area,
call our Applications Group at 847-866-2525, Shure Europe at 49-1731-72140, Shure Asia at 852-2893-4290, or visit the Technical Support
section at www.shure.com.
H2
R8
Q3
S5
(518-554)MHz
North America,
Europe
(800-814)MHz
(748-784)MHz
(842-865)MHz
Europe
France, Australia
England
1
518.750
801.100
749.100
855.275
2
524.875
802.325
754.025
856.175
3
525.625
805.050
756.000
857.625
4
534.375
808.600
765.900
858.200
5
536.875
810.550
772.000
863.075
6
538.500
811.600
775.000
863.625
7
551.000
813.300
778.775
864.425
8
553.250
813.800
781.900
864.850
CHANNEL
Channel A (P2R Only)
Wired Mode (RF Disabled)
13
ENGLISH
Certifications
PS20: Conforms to applicable U.S. and Canadian electrical and safety
standards.
PS20E/PS20UK: Conforms to European low voltage directive
72/23/EEC. Eligible to bear CE marking.
P2T: Certified to FCC Part 74 (FCC ID No. DD4P2T). Certified in Canada by IC to RSS-123 and RSS-102 (Certification No. 616A-P2T). This
class B digital apparatus complies with Canadian ICES–003.
EP2T/UKP2T: Meets essential requirements of European R&TTE DiO682
rective 99/5/EC, eligible to bear the CE mark:
. Type approved to EN 300 422 Parts 1 and 2. Meets requirements of EMC Standard EN 301 489 Parts 1 and 9.
P2R: Approved under the Declaration of Conformity (DoC) provision of
FCC Part 15. Certified in Canada by IC to RSS-123 (Certification No.
616A-P2R). This class B digital apparatus complies with Canadian
ICES–003. Meets essential requirements of European Union R&TTE
Directive 99/5/EC, eligible to bear
mark. Meets requirements of
EMC standards EN 300 422 Parts 1 and 2 and EN 301 489 Parts 1
and 9.
SHURE
P2R
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
The term “IC:” before the radio certification number only signifies that
Industry Canada technical specifications were met.
APPENDIX
P2R Receiver MIX IN Jack Wiring Diagram
5 V BIAS
Mono Line Input
The MIX IN jack accepts line-level signals, such as
click tracks, effects processors, pre-amp outputs
from guitar or bass amps, or line outputs from mixing consoles. When used with a mono connector,
the ring of the MIX IN jack is grounded. This doesn’t
harm the P2R.
SLEEVE
RING
PRE–AMP
TIP
14
1 MEG OHM
Declaration of Conformity
EU DECLARATION OF CONFORMITY
We of
Shure Incorporated
222 Hartrey Ave.
Evanston IL 60202-3696 U.S.A.
847-866-2200
We,
of
Declare under our sole responsibility that the following products
declare under our sole responsibility that the following products,
Model: P2R
Name: P2R Receiver
were tested and found to comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Testing was completed by the following NVLAP or A2LA accredited
laboratory:
Model: P2T
Description: Transmitter
Model: P2R
Description: Receiver
Model: PS20E, PS20UK
Description: AC/DC Power Adapter
Conform to the essential requirements and other relevant previsions
of the R&TTE Directive (1995/5/EC).
The products comply with the following product family, harmonized or
national standards:
L. S. Compliance, Inc.
W66 N220 Commerce Ct.
Cedarburg, Wisconsin 53012 U.S.A.
P2T:
ETSI EN 300 422–1
ETSI EN 301 489–1
P2R:
ETSI EN 300 422–1
ETSI EN 301 489–1
PS20E/PS20UK: EN60065
At the test location of
L. S. Compliance, Inc.
W66 N220 Commerce Ct.
Cedarburg, Wisconsin 53012, U.S.A.
ETSI EN 300 422–2
ETSI EN 301 489–9
ETSI EN 300 422–2
ETSI EN 301 489–9
Manufacturer: Shure Incorporated
Signed:
Name, Title:
Shure Incorporated., Manufacturer.
Signed:
Shure Incorporated
222 Hartrey Avenue
Evanston, IL 60202–3696, U.S.A.
Date: April 3, 2002
Craig Kozokar
Project Engineer, Corporate Quality, Shure Incorporated
European Contact: Shure Europe GmbH
Wannäcker Str. 28, 74078 Heilbronn, Germany
Phone: 49–7131–7214–0, Fax: 49–7131–7214–14
Date: March 04, 2002
Name, Title: Craig Kozokar, Project Engineer, Corporate Quality,
Shure Incorporated
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
90
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement