Eizo FDX1001T, DuraVision FDX1201T, FDV1001T User manual

Eizo FDX1001T, DuraVision FDX1201T, FDV1001T User manual
Important
Please read this User’s Manual carefully to familiarize yourself with safe and
effective usage.
Please retain this manual for future reference.
重要事项
请仔细阅读用户手册,掌握如何安全、有效地使用本产品。
请保留本手册,以备日后参考。
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: DuraVision FDX1001T/FDV1001T/FDX1201T
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
SAFETY SYMBOLS
This manual and this product use the safety symbols below. They denote critical information. Please read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage.
Indicates an attention to be required. For example, the symbol
risk of electric shock”.
Indicates a prohibited action. For example, the symbol
such as “Do not disassemble”.
illustrates the hazard type such as “the
illustrates a particular prohibited action
Indicates a mandatory action that must be followed. For example, the symbol
notification of general prohibition such as “Grounding the unit”.
illustrates the
Using the special functions, such as screen size change (ex. changing the horizontal and vertical ratio of images input)
for commercial purposes or for the purpose of showing in public may violate copyright laws.
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside
this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential
unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
Apple, ColorSync, eMac, iBook, iMac, iPad, Mac, MacBook, Macintosh, Mac OS, PowerBook, and QuickTime are registered trademarks
of Apple Inc.
Windows, Windows Media, Windows Vista, SQL Server, and Xbox 360 are registered trademarks of Microsoft Corporation in the United
States and other countries.
VESA is a registered trademark of Video Electronics Standards Association.
NEC is a registered trademark of NEC Corporation.
PC-9801 and PC-9821 are trademarks of NEC Corporation.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor, and ScreenManager are
registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.
All other company and product names are trademarks or registered trademarks of their respective owners.
2
PRECAUTIONS
IMPORTANT
• To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit
(refer to the figure below).
【Location of Caution Statement】
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange
noises,disconnect all power connections immediately and contact your dealer for
advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in fire, electric
shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet
may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet,
unplug the unit immediately. Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage. If the unit
falls, disconnect the power immediately and ask your dealer for advice. Do not continue using a damaged
unit. Using a damaged unit may result in fire or electric shock.
3
WARNING
Use the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
• Do not place outdoors.
• Do not place in a transportation system (ship, aircraft, train, automobile, etc.) where it may be affected
by strong vibration or shock.
• Do not place in a dusty or humid environment.
• Do not place in a location where water is splashed on the screen (bathroom, kitchen, etc.).
• Do not place in a location where the steam comes directly on the screen.
• Do not place near heat generating devices or a humidifier.
• Do not place in a location where the product is subject to direct sunlight.
• Do not place in an inflammable gas environment.
To avoid danger of suffocation, keep the plastic packing bags away from babies and
children.
Use the enclose AC adapter.
The enclosed AC adapter is for use with this product only. Do not use the AC adapter with other
equipment. Connecting to power sources that do not match the power ratings of the AC adapter may
result in fire or electric shock.
Make sure the power cord meets the following requirements.
This product does not include a power cord. Please provide separately a power cord which meets the
requirements. (For more information, please contact your dealer.)
• The power cord is compatible with the standards of the country and region in which
this product is to be used.
• The power cord has a rated value of at least 2.5A.
Power supply: 100-240Vac 50/60Hz
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
Use the correct voltage.
• The unit is designed for use with a specific voltage only. Connection to another voltage than specified
in this User’s Manual may cause fire, electric shock, or equipment damage.
Power supply: 100-240Vac 50/60Hz
• Do not overload your power circuit, as this may result in fire or electric shock.
Handle the power cord and AC adapter with care.
Do not place heavy objects on, pull or tie the power cord or the AC adapter. Use of a damaged cord or
AC adapter may result in fire or electric shock.
Never touch the plug, AC adapter or power cord during a thunderstorm.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and
install the unit securely.
Not doing so may cause the unit to become unattached, which may result in injury or equipment damage.
When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit.
Using a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.
4
WARNING
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the eyes or mouth. If any part
of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical
symptoms result, please consult your doctor.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached
is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit firmly withboth hands
ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
Do not install the unit in a closed space.
If the inerior becomes hot, it may result in fire, electric shock or damage.
Do not touch the power plug or AC adapter with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a problem.
Mind that the AC adapter becomes hot during use.
• Do not cover or place anything on top of the AC adapter. Do not place the AC adapter on top of
things that trap heat such as carpets, blankets, etc. Keep the AC adapter away from direct sunlight
and heat sources such as heaters.
Not doing so may result in fire.
• Do not touch with bare hands. Doing so may result in burns.
Do not suspend the AC adapter in midair.
Using it while suspended in midair may result in fire or electric shock.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period, disconnect the power cord
from the wall socket after turning off the power for safety and power conservation.
5
Notice for this monitor
Aside from displaying microscope images, this product is also suited to the dedicated usages such as operation of
terminal equipment.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used
outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to
“Cleaning” on the next page.)
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.99% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your local EIZO representative.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt to
brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until the
dew condensation disappears, otherwise it may cause some damage to the monitor.
(Cautions for the Use of the Touch Panel)
• During touch operation
Be careful of the following points. Otherwise, damage may occur to the monitor.
-- Do not strongly press, scratch, or poke the panel.
-- Do not touch the panel with hard objects such as ballpoint pens or metals.
6
Cleaning
ATTENTION
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or
panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.
NOTE
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth
with water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
7
CONTENTS
Cover
............................................................. 1
PRECAUTIONS................................................. 3
Notice for this monitor............................................... 6
CONTENTS............................................................. 8
Chapter 1 Introduction........................................ 9
1-1. Features............................................................... 9
1-2. Package Contents............................................... 9
1-3. Controls and Functions.................................... 10
Chapter 2 Connecting Cables.......................... 11
2-1. Connection Procedures.....................................11
● When used as a PC monitor..............................11
● When using video equipment............................ 12
2-2. Adjusting the Screen Angle.............................. 13
2-3.Installing the Touch Panel Driver...................... 14
2-4.Calibrating the Monitor...................................... 14
Chapter 3 Settings and Adjustments............... 15
3-1. Basic Operation and Functions....................... 15
3-2. Color Adjustment.............................................. 17
3-3. Configure other settings................................... 18
Chapter 4 Troubleshooting............................... 19
Chapter 5 Reference.......................................... 21
5-1. Attaching an Arm............................................... 21
5-2. Specifications.................................................... 22
5-3. Glossary............................................................. 28
5-4. Preset Timing..................................................... 29
LIMITED WARRANTY........................................... 30
8
CONTENTS
Chapter 1
Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• FDX1001T/FDV1001T: 10.4-inch screen, FDX1201T: 12.1-inch screen
• Resolution
- FDX1001T/FDX1201T: XGA (1024 × 768) display compliant
- FDV1001T: VGA (640 × 480) display compliant
• Maximum brightness
FDX1001T: 460 cd/m2, FDV1001T: 350 cd/m2, FDX1201T: 780 cd/m2
• LED backlight LCD panel
The LED backlight provides better power efficiency and reduced power consumption compared to existing
fluorescent backlight LCD panels.
No mercury, a hazardous substance, is used.
• Analog signal support
PC signal: D-Sub mini 15 pin connector × 1
- FDX1001T/FDX1201T: Horizontal scanning frequency 24 kHz - 50 kHz
Vertical scanning frequency 55 Hz - 75 Hz
- FDV1001T: Horizontal scanning frequency 24 kHz - 32 kHz
Vertical scanning frequency 56 Hz - 70.5 Hz
Video signal: S-Video/ Video input connector × 1
- Applicable Format NTSC, PAL, SECAM
• Resistive technology touch panel function
Enables touch operation of the PC screen.
• Crosshair display function
Displays lines (Fine, Circle or Broken Line) as a reference for the position of the image displayed on the monitor.
3-3. Configure other settings (page 18)
• Video aspect function
Alters the display range of the input image (overscan). 3-3. Configure other settings (page 18)
1-2. Package Contents
Check that all the following items are included in the packaging box. If any items are missing or damaged,
contact your local dealer.
NOTE
• Please retain the packing materials for future transport of the monitor.
• LCD Monitor
• AC Adapter
• Cable Tie
• User’s Manual (Limited Warranty included)
• EIZO LCD Utility Disk (CD-ROM)*1
• RS-232C Cable
*1 The
disk includes the touch panel driver.
For how to install the touch panel driver, see the Touch Panel Driver User’s Manual (on the CD-ROM).
ATTENTION
• This product does not include a power cord. Please provide separately a power cord which meets the usage
requirements.
Chapter 1 Introduction
9
1-3. Controls and Functions
12
Setting menu
13
1
1
button
2
button
3
4
2
3
4
5
6
7
8
9
11
Switches the input signal.
button
button
Displays the Setting menu, fixes the setting or adjustment items on each menu,
and saves the setting or adjustment results.
・Used to select the setting or adjustment items, or to increase or decrease the
adjustment values on each menu.
or
switches
・When the settings menu is not displayed, pressing
between displaying and not displaying the crosshair.
Turns the power on or off.
Indicates monitor’s operation status.
5 Power indicator
Blue
: Operating
Orange : Power off
6 Maintenance port
Serial port for the touch
7
panel
8 Power jack (DC-IN)
9 Input signal connector
10 Input signal connector
11 Input signal connector
12 Cable holder
13 Cable tie
10
10
Chapter 1 Introduction
For monitor control
Connects the PC to the monitor with an RS-232C cable.
Connects to the AC adapter.
D-Sub mini 15-pin connector × 1
S-Video input connector × 1
Video input connector × 1
Covers the monitor cables.
Clinches the cables.
Chapter 2
Connecting Cables
2-1. Connection Procedures
1 Connects to external equipment compatible with the monitor.
・ When used as a PC monitor・・・・・・・・・・・・・・・・・・・・・・・・・・ page 11
・ When using video equipment・・・・・・・・・・・・・・・・・・・・・・・・・ page 12
● When used as a PC monitor
ATTENTION
• When replacing the current monitor with an FDX1001T / FDV1001T /FDX1201T monitor, be sure to change the
PC settings for resolution and vertical frequency to those which are available for the FDX1001T / FDV1001T/
FDX1201T monitor referring to the resolution table (see below) before connecting the PC.
Compatible Resolutions/Frequencies
The monitor supports the following resolutions.
・FDX1001T/FDX1201T
Resolution
640 × 400
640 × 400
640 × 480
640 × 480
720 × 400
800 × 600
832 × 624
1024 × 768*1
*1
Display Mode
NEC PC-9801
NEC PC-9821 AP2
Apple Macintosh
VGA, VESA
VGA TEXT
VESA
Apple Macintosh
VESA
Frequency
56 Hz
70 Hz
67 Hz
~75 Hz
70 Hz
~75 Hz
75 Hz
60 Hz
Dot Clock
~65 MHz
Recommended resolution (Set this resolution.)
・FDV1001T
Resolution
640 × 480
640 × 480
Display Mode
Apple Macintosh
VGA
Frequency
67 Hz
60 Hz
Dot Clock
~31 MHz
Chapter 2 Connecting Cables
11
(1)Connect the monitor to the PC with a signal cable that matches the connectors.
After connecting the cable connectors, tighten the screws of the connectors to secure the coupling.
monitor
PC
D-Sub mini 15-pin
connector
Signal cable MD-C87 (optional)
D-Sub mini 15-pin
connector
or
Signal cable FD-C16 (optional)
DVI connector
● When using video equipment
(1)Connect the monitor to the video equipment with a signal cable that matches the connectors.
monitor
Video equipment
S-Video
S-Video cable (Commercially available product)
S-Video
or
Video
12
Chapter 2 Connecting Cables
Video cable (Commercially available product)
Video
2 Plug the power cord of the monitor into a power outlet.
(1) Connect the power cord to the AC adapter.
(2) Connect the AC adapter to the Power jack of the monitor, and after that, connect the power plug to a
power outlet.
ATTENTION
• This product does not include a power cord. Please provide separately a power cord which meets the usage
requirements.
• For the maximum power saving, it is recommended that the Power button be turned off. Unplugging the power cord
completely shuts off power supply to the monitor.
2-2. Adjusting the Screen Angle
Hold left and right edge of the monitor with both hands, and adjust the tilt and swivel to the best condition
for working.
Chapter 2 Connecting Cables
13
2-3.Installing the Touch Panel Driver
ATTENTION
• The user account to be used for installing the touch panel driver must have the “Administrators” privilege.
• When reinstalling the touch panel driver to update the driver, etc., restart the PC after uninstalling the driver and
then install it.
1 Uninstall the other touch panel driver, if it is installed.
2 Install the touch panel driver according to the instructions included in the CDROM.
For how to install the touch panel driver, see the Touch Panel Driver User’s Manual (on the CD-ROM).
3 Connect the monitor to the PC with the included RS-232C signal cable.
Connectors on the
monitor
Connectors on the PC
COM port
RS-232C Cable (supplied)
Serial port for the
touch panel
4 Restart the PC.
ATTENTION
• After the restart, set up the device using the following procedure. For details, refer to the Touch Panel Driver User’s
Manual (on the CD-ROM).
1. Click “Start” - “All Program” - “DMC” - “DMC Touch Panel Configuration” to display the [Properties] window.
2. Click “Add a serial device”, and register a new serial device.
3. Click “Device”, and specify the COM port number used for [COM port].
4. Click “Apply”.
5. Click “Close”.
2-4.Calibrating the Monitor
Calibrate the monitor according to the instruction manual for the touch panel driver on the CD-ROM.
14
Chapter 2 Connecting Cables
Chapter 3
Settings and Adjustments
3-1. Basic Operation and Functions
Basic operation of Setting menu
1 Displaying Setting Menu
Press
.
2 Setting/Adjusting
3 Exiting
Choose [Exit] with
or
, and press
.
NOTE
• Keeping
pressed for 2 seconds will also exit the Setting menu.
Chapter 3 Settings and Adjustments
15
Functions
The settings adjustable in the Setting menu are as shown below. The availability of items depends on the
input signal.
√ : Configurable ― : Not configurable
Tab
Color
PC
Video
Reference
Brightness
Setting / adjustable item
√
√
page 17
Contrast
√
√
Black Level
√
√
Sharpness
―
√
Saturation
―
√
Hue
PC Settings
―
√
Clock
√
―
Phase
√
―
Position
√
―
Range Adjustment
√
―
Color Mode
√
―
Red/Green/Blue
Reset
Others
―
√
―
Reset
√
√
Video Aspect
―
√
Power Save
√
√
Reverse
√
√
√
√
Crosshair
16
√
Color
√
√
Width
√
√
Beep
√
√
Language
√
√
Touch Panel
√
√
Information
√
√
Chapter 3 Settings and Adjustments
page 18
3-2. Color Adjustment
This will perform color adjustments.
Please switch between the input screens you want to adjust and adjust them one by one.
Adjustable item / adjustable value
Adjusting
Brightness
0 - 30
Adjusts the brightness of the backlight.
Contrast
0 - 30
Adjusts the contrast.
Black Level
0 - 30
Adjusts the image brightness.
Sharpness
Off/Low/High
Adjusts the image outlines.
Saturation
-30 - +30
Adjusts the saturation.
Hue
-30 - +30
Adjusts the hue.
PC Settings*1
Clock
Adjust this when vertical bars appear.
Phase
Adjust this when the screen appears to flicker or blur.
Position
Adjust this when the display positioning is misaligned.
Range Adjustment
Provides automatic adjustment when you want every
color gradients displayed.
Color Mode*2
Red/Green/
Blue
1/2/3
0 - 128
Reset
Reset
Select Color Mode (1/2/3) to adjust the colors of red,
green and blue in several modes.
Resets the state adjusted with [PC Settings] to the
factory default.
Resets the state adjusted with the [Color] tab to the
factory default (excluding [PC Settings]).
*1
This setting becomes available when a PC is connected to the monitor. Please adjust with a PC when display and color adjustments
are required.
*2
Perform [Range Adjustment] before adjusting Color Mode.
Chapter 3 Settings and Adjustments
17
3-3. Configure other settings
This will configure other settings.
Setting item / setting value
Setting
Video Aspect
Configures the display range of the input image (overscan).
Normal/100%
“Normal”
:
Displays the input image with the
outmost parts slightly cut off.
*This is how display devices
normally display images.
“100%”
:
Displays most of the input image.
*Because a part of the image
which normally gets cut off is
displayed as well, noise may be
visible around the outmost parts,
depending on the input signal.
Power Save
Disable/Enable
Automatically turns off the power supply if no video signal has
been received for 15 minutes during PC or video viewing.
Reverse
Off/On
Displays the image upside down (180 degree rotation).
Crosshair
Off/Fine/Circle/
Broken Line
Displays a crosshair as a reference for the position of the image.
“Fine”
“Circle”
“Broken Line”
(When the settings menu is not displayed, pressing
or
switches between displaying and not displaying the crosshair.)
Color
When “Fine” is
selected:
Black/White/Red/
Green
When “Circle” or
“Broken Line” is
selected:
Black/White
Configures the color of the crosshair.
Width
Narrow/Wide
Configures the thickness of the crosshair’s lines.
Off/On
Sets button press sounds and connection error sounds to on or
off.
Beep
• Short beep
: - When
,
or
is pressed.
- When an item is selected with
• Long beep
• 2 short beeps
• 4 short beeps
.
- When a maximum or minimum value is
or .
set with
: When registration is performed with .
: When the Setting menu is displayed and
is pressed.
: - When there is no input signal.
- When a frequency out of the specified
range is received.
Language
日本語 /English
Configures the displayed Setting menu and message language.
Touch Panel
PC+VIDEO/PC/
VIDEO
Select an input that enables touch panel operation.
Information
18
Chapter 3 Settings and Adjustments
Reviews the input signals, usage time and model name.
Chapter 4
Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
Common
Problems
Possible cause and remedy
No picture
• Power indicator does not light.
• Check whether the power cord is connected correctly.
• If the problem persists, turn off the power, and then turn
it on again a few minutes later.
• Power indicator lights orange.
• Press
• Power indicator lights blue.
• Check whether the power of the connected device is
turned on.
• Switch the input signal.
• Set each adjusting value in [Brightness] and [Contrast] to
higher level. (see page 17)
.
The screen is too bright or too dark.
• Adjust using [Brightness] or [Contrast]. (The LCD
monitor backlight has a fixed life span. When the screen
becomes dark or begins to flicker, contact your local
dealer.) (see page 17)
Green/red/blue/white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a
failure.
Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• When displaying the same image for extended periods of
time, please set up the screen saver and/or make use of
the power saving function.
When displaying on a PC screen
Problems
Possible cause and remedy
The message below appears.
• This message appears when no signal
is input.
PC
No
Signal
• The message shows that the input
signal is out of the specified frequency
range.
PC
Signal
Error
• This message appears when the signal is not input
correctly even when the monitor functions properly.
• The message shown left may appear, because some
PCs do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
monitor. (see page 22, 23, 24) (Current input signal can
be checked in [Information].)
• Reboot the PC.
• Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
Display position is incorrect.
• Adjust image position using [Position]. (see page 17)
Vertical bars appear on the screen or a
part of the image is flickering.
• Adjust using [Clock]. (see page 17)
Whole screen is flickering or blurring.
• Adjust using [Phase]. (see page 17)
Characters are blurred.
• This may occur when a non-complying high-resolution
signal is input. Check the PC settings and change the
resolution which complies with the monitor.
Chapter 4 Troubleshooting
19
Touch panel problems
20
Problems
Possible cause and remedy
Cursor position is not correct. / Cursor
jumps.
• Turn off and on the monitor. If the symptom is not
improved, perform the calibration on the monitor.
• Touch with one finger only.
• Connect the monitor to the PC with the cable indicated
in the User’s Manual of the monitor. Using a conversion
adapter, the touch panel may not operate properly.
Touch operation is not effective.
• Check whether “Use EEPROM” in the [Device] menu
is not checked in the [Properties] settings of the touch
panel driver. If the check is already applied, perform the
calibration.
• Other login user may have changed the setting. Set the
touch panel driver again.
• Restart “DMC Touch Panel Configuration”, or reboot the
PC.
Some deflection may appear on the
surface of touch panel portion.
• Due to the touch panel structural characteristics, the
deflection may occur on the touch panel surface in high
temperature/high humidity operating environment. This is
not a trouble.
No touch-sound.
• The touch-sound may not be output from the external line
out of the PC depending on the hardware configuration.
• Under Windows 7, touch-sound is only output through
the audio output terminal of the PC. To hear touchsound, connect speakers.
Chapter 4 Troubleshooting
Chapter 5
Reference
5-1. Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use
an arm or stand of EIZO option.
ATTENTION
• When attaching an arm or stand, follow the instructions of their user’s manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to
the VESA standard. Use the M4 × 12 mm screws in use by this monitor.
- Clearance between the screw holes : 100 mm × 100 mm
- Thickness of plate : 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• Connect the cables after attaching an arm or a stand.
• Since the monitor and arm are so heavy, dropping them may result in injury or equipment damage.
• Do not turn the monitor lengthwise.
[Attachment Procedure]
1 Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2 Remove the stand.
Prepare a screwdriver. Unscrew the four screws securing the unit and the stand with the screwdriver.
3 Attach the monitor to the arm or stand.
Secure the monitor to the arm or stand using the screws specified in the user’s manual of the arm or stand.
Chapter 5 Reference
21
5-2. Specifications
FDX1001T
LCD Panel
Size
10.4-inch (260 mm) TFT color LCD
Surface treatment
Anti-glare
Surface hardness
2H
Viewing angle
Horizontal 160°, Vertical 130° (CR : 10 or more)
Dot Pitch
0.2055 mm
Display Area (H × V)
210.4 mm × 157.8 mm
Resolution
1024 dots × 768 lines
Max. Display Color
Approx. 16.7 million colors
PC input
Horizontal Scan Frequency 24-50 kHz
Vertical Scan Frequency
55-75 Hz (Non-interlace)
Max. Dot Clock
65 MHz
Input Signal Connector
D-Sub mini 15-pin × 1
Input Signal (Sync)
Separate, TTL, positive / negative
Input Signal (Video)
Analog, Positive (0.7Vp-p/75Ω)
Max. Video Signal Memory 15 (preset : 13)
Video input
Plug and Play
VESA DDC 2B/EDID structure 1.3
Touch Panel
OS: Microsoft Windows 7 Service Pack 1 (32 bit/64 bit)
Microsoft Windows Vista Service Pack 2 (32 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Communication protocol : RS-232C serial
Detective method : Analog resistive technology
Applicable Format
NTSC, PAL, SECAM
Input Signal Connector
S-Video DIN mini 4 pin/ Video Pin jack × 1
Input Signal Level
S-Video DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω
Video Pin jack : 1.0Vp-p/75Ω
Power Supply
Power
Consumption
Screen Display On
AC adapter (AC) : 14 W or less
Main unit (DC) : 11 W or less
Power Off
AC adapter (AC) : 1.3 W or less
Main unit (DC) : 0.5 W or less
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
252 mm (9.9 inch) × 255 mm (10 inch) × 175 mm (6.9 inch)
Main unit (without stand)
252 mm (9.9 inch) × 216 mm (8.5 inch) × 45 mm (1.77 inch)
Mass
Main unit
Approx. 3.9 kg (8.6 lbs.)
Main unit (without stand)
Approx. 2.3 kg (5.1 lbs.)
Tilt
30°Up, 0°Down
Swivel
35°Right, 35°Left
Movable
range
22
AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.3-0.2 A (Max.)
Main unit (DC) : 12VDC±10%, 0.9 A
Chapter 5 Reference
Environmental Temperature
Conditions
[Operating temperature]
Main unit : 0 °C - 50 °C (32 °F - 122 °F)
AC adapter : 0 °C - 40 °C (32 °F - 104 °F)
[Storage temperature]
-20 °C - 60 °C (-4 °F - 140 °F)
Humidity
[Operating humidity]
Main unit : 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102
°F), no condensation)
AC adapter : 20% - 85% R.H.(no condensation)
[Storage humidity]
10% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no
condensation)
Pressure
[Operating] 700 hPa - 1060 hPa
[Storage] 200 hPa - 1060 hPa
Size
10.4-inch (260 mm) TFT color LCD
Surface treatment
Anti-glare
Surface hardness
2H
Viewing angle
Horizontal 160°, Vertical 140° (CR : 10 or more)
Dot Pitch
0.33 mm
FDV1001T
LCD Panel
Display Area (H × V)
211.2 mm × 158.4 mm
Resolution
640 dots × 480 lines
Max. Display Color
Approx. 16.2 million colors
PC input
Horizontal Scan Frequency 24-32 kHz
Vertical Scan Frequency
56-70.5 Hz (Non-interlace)
Max. Dot Clock
31 MHz
Input Signal Connector
D-Sub mini 15-pin × 1
Input Signal (Sync)
Separate, TTL, positive / negative
Input Signal (Video)
Analog, Positive (0.7Vp-p/75Ω)
Max. Video Signal Memory 10 (preset : 8)
Video input
Plug and Play
VESA DDC 2B/EDID structure 1.3
Touch Panel
OS: Microsoft Windows 7 Service Pack 1 (32 bit/64 bit)
Microsoft Windows Vista Service Pack 2 (32 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Communication protocol : RS-232C serial
Detective method : Analog resistive technology
Applicable Format
NTSC, PAL, SECAM
Input Signal Connector
S-Video DIN mini 4 pin/ Video Pin jack × 1
Input Signal Level
S-Video DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω
Video Pin jack : 1.0Vp-p/75Ω
Power Supply
Power
Consumption
AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.2-0.15 A (Max.)
Main unit (DC) : 12VDC±10%, 0.7 A
Screen Display On
AC adapter (AC) : 10 W or less
Main unit (DC) : 9 W or less
Power Off
AC adapter (AC) : 1.3 W or less
Main unit (DC) : 0.5 W or less
Chapter 5 Reference
23
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
252 mm (9.9 inch) × 255 mm (10 inch) × 175 mm (6.9 inch)
Main unit (without stand)
252 mm (9.9 inch) × 216 mm (8.5 inch) × 45 mm (1.77 inch)
Mass
Main unit
Approx. 3.7 kg (8.2 lbs.)
Main unit (without stand)
Approx. 2.1 kg (4.6 lbs.)
Tilt
30°Up, 0°Down
Swivel
35°Right, 35°Left
Movable
range
Environmental Temperature
Conditions
[Operating temperature]
Main unit : 0 °C - 50 °C (32 °F - 122 °F)
AC adapter : 0 °C - 40 °C (32 °F - 104 °F)
[Storage temperature]
-20 °C - 60 °C (-4 °F - 140 °F)
Humidity
[Operating humidity]
Main unit : 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102
°F), no condensation)
AC adapter : 20% - 85% R.H.(no condensation)
[Storage humidity]
10% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no
condensation)
Pressure
[Operating] 700 hPa - 1060 hPa
[Storage] 200 hPa - 1060 hPa
Size
12.1-inch (310 mm) TFT color LCD
Surface treatment
Anti-glare
Surface hardness
2H
Viewing angle
Horizontal 160°, Vertical 140° (CR : 10 or more)
Dot Pitch
0.240 mm
FDX1201T
LCD Panel
Display Area (H × V)
245.76 mm × 184.32 mm
Resolution
1024 dots × 768 lines
Max. Display Color
Approx. 16.7 million colors
PC input
Horizontal Scan Frequency 24-50 kHz
Vertical Scan Frequency
55-75 Hz (Non-interlace)
Max. Dot Clock
65 MHz
Input Signal Connector
D-Sub mini 15-pin × 1
Input Signal (Sync)
Separate, TTL, positive / negative
Input Signal (Video)
Analog, Positive (0.7Vp-p/75Ω)
Max. Video Signal Memory 15 (preset : 13)
24
Chapter 5 Reference
Plug and Play
VESA DDC 2B/EDID structure 1.3
Touch Panel
OS: Microsoft Windows 7 Service Pack 1 (32 bit/64 bit)
Microsoft Windows Vista Service Pack 2 (32 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Communication protocol : RS-232C serial
Detective method : Analog resistive technology
Video input
Applicable Format
NTSC, PAL, SECAM
Input Signal Connector
S-Video DIN mini 4 pin/ Video Pin jack × 1
Input Signal Level
S-Video DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω
Video Pin jack : 1.0Vp-p/75Ω
Power Supply
Power
Consumption
AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.4-0.25A (Max.)
Main unit (DC) : 12VDC±10%, 1.4 A
Screen Display On
AC adapter (AC) : 20 W or less
Main unit (DC) : 17 W or less
Power Off
AC adapter (AC) : 1.6 W or less
Main unit (DC) : 0.8 W or less
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
293 mm (11.5 inch) × 271 mm (10.7 inch) × 175 mm (6.9 inch)
Main unit (without stand)
293 mm (11.5 inch) × 244 mm (9.6 inch) × 46 mm (1.81 inch)
Mass
Main unit
Approx. 4.4 kg (9.7 lbs.)
Main unit (without stand)
Approx. 2.8 kg (6.2 lbs.)
Tilt
30°Up, 0°Down
Swivel
35°Right, 35°Left
Movable
range
Environmental Temperature
Conditions
[Operating temperature]
Main unit : 0 °C - 50 °C (32 °F - 122 °F)
AC adapter : 0 °C - 40 °C (32 °F - 104 °F)
[Storage temperature]
-20 °C - 60 °C (-4 °F - 140 °F)
Humidity
[Operating humidity]
Main unit : 20% - 90% R.H. (wet bulb temperature ≤ 39 °C (102
°F), no condensation)
AC adapter : 20% - 85% R.H.(no condensation)
[Storage humidity]
10% - 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no
condensation)
Pressure
[Operating] 700 hPa - 1060 hPa
[Storage] 200 hPa - 1060 hPa
Main default settings (factory settings)
PC
Video
Brightness
Contrast
Black Level
30
FDX1001T/FDX1201T: 30
FDV1001T: 24
15
30
15
Sharpness
Saturation
Off
-
0
Hue
-
0
Color Mode
1
-
Video Aspect
Normal
Power Save
Enable
Reverse
Off
Crosshair
Off
Beep
On
Language
Touch Panel
English
PC+VIDEO
Chapter 5 Reference
25
Outside Dimensions
unit : mm (inch)
45 (1.77)
21 (0.83)
FDX1001T / FDV1001T
30°
20 (0.79)
36 (1.42)
93 (3.66)
291 (11.5)
252 (9.9)
213 (8.4)
160 (6.3)
216 (8.5)
255 (10.0)
20 (0.79)
20 (0.79)
35°
35°
175 (6.9)
201 (7.9)
200 (7.9)
22 (0.87)
200 (7.9)
30°
84 (3.31)
34.8 (1.37)
186 (7.3)
244 (9.6)
271 (10.7)
247.4 (9.7)
22.8 (0.90)
306 (12.0)
293 (11.5)
22.8 (0.90)
23.2 (0.91)
35°
35°
46 (1.81)
FDX1201T
175 (6.9)
207 (8.1)
26
Chapter 5 Reference
Connector Pin Assignment
• D-Sub mini 15-pin connector
3
4
5
1
2
8
9
10
7
6
14 13 12 11
15
Pin No.
Signal
1
Red video
Pin No.
6
Signal
Red video ground
Pin No.
11
Signal
NC*
2
Green video
7
Green video ground
12
Data (SDA)
3
Blue video
8
Blue video ground
13
H. Sync
4
NC*
9
NC*
14
V. Sync
5
Ground
10
Ground
15
Clock (SCL)
(NC*: No Connection)
• Serial port for the touch panel
3
2
1
6
7
5
4
8
9
Pin No.
Signal
Pin No.
Signal
1
DCD
6
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
Ground
Chapter 5 Reference
27
5-3. Glossary
Afterimage
The Afterimage is particular to LCD monitors. When the monitor screen is left on for a long period without
use. The Afterimage can be removed gradually by changing the displayed image.
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics
system in use, when the analog input signal is converted to a digital signal for image display. This is called
clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation.
It is recommended that range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This
monitor consists of 1024 (FDX1001T/FDX1201T) / 640 (FDV1001T) horizontal pixels and 768
(FDX1001T/FDX1201T) / 480 (FDV1001T) vertical pixels.
At a resolution of 1024 × 768 (FDX1001T/FDX1201T) / 640 × 480 (FDV1001T), all pixels are illuminated
as a full screen (1:1).
28
Chapter 5 Reference
5-4. Preset Timing
The following table shows the factory preset video timing of the PC.
ATTENTION
• Display position may be deviated depending on the PC connected, which may require screen adjustment using
Setting menu.
• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen
display may still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the
Setting menu.
FDX1001T/FDX1201T
Resolution
Applicable
signal
Frequency
Horizontal :
kHz
31.47
Polarity
Vertical :
Hz
70.09
720 × 400
VGA TEXT
Dot clock :
MHz
28.33
Negative
Positive
640 × 480
VGA
25.18
31.47
59.94
Negative
Negative
640 × 480
VESA
31.50
37.86
72.81
Negative
Negative
640 × 480
VESA
31.50
37.50
75.00
Negative
Negative
800 × 600
VESA
36.00
35.16
56.25
Positive
Positive
800 × 600
VESA
40.00
37.88
60.32
Positive
Positive
800 × 600
VESA
50.00
48.08
72.19
Positive
Positive
800 × 600
VESA
49.50
46.88
75.00
Positive
Positive
1024 × 768
VESA
65.00
48.36
60.00
Negative
Negative
640 × 480
MAC
30.24
35.00
66.67
Negative
Negative
832 × 624
MAC
57.28
49.72
74.55
Negative
Negative
640 × 400
PC-9801
21.05
24.83
56.42
Negative
Negative
640 × 400
PC-9821 AP2
25.18
31.48
70.10
Negative
Negative
Dot clock :
MHz
28.33
Frequency
Horizontal :
kHz
31.47
Vertical :
Hz
70.09
Horizontal
Vertical
FDV1001T
Resolution
Applicable
signal
720 × 400
VGA TEXT
Polarity
Horizontal
Vertical
Negative
Positive
640 × 480
VGA
25.18
31.47
59.94
Negative
Negative
800 × 600
VESA
36.00
35.16
56.25
Positive
Positive
800 × 600
VESA
40.00
37.88
60.32
Positive
Positive
1024 × 768
VESA
65.00
48.36
60.00
Negative
Negative
640 × 480
MAC
30.24
35.00
66.67
Negative
Negative
640 × 400
PC-9801
21.05
24.83
56.42
Negative
Negative
640 × 400
PC-9821 AP2
25.18
31.48
70.10
Negative
Negative
Chapter 5 Reference
29
LIMITED WARRANTY
EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter
referred to as the “Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter
referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who
purchased the product specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors,
that EIZO and Distributors shall, at their sole discretion, either repair or replace the Product at no charge if the Original
Purchaser becomes aware within the Warranty Period (defined below) that the Product malfunctions or is damaged in the
course of normal use of the Product in accordance with the description in the instruction manual attached to the Product
(hereinafter referred to as the “User’s Manual”).
The period of this Warranty is two (2) years from the date of purchase of the Product (hereinafter referred to as the
“Warranty Period”). EIZO and Distributors shall bear no liability or obligation with regard to the Product in relation to the
Original Purchaser or any third parties other than as provided under this Warranty.
EIZO and Distributors will cease to hold or store any parts of the Product upon expiration of seven (7) years after the
production of such parts is discontinued. In repairing the monitor, EIZO and Distributors will use renewal parts which
comply with our QC standards.
The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict
any legal rights of the Original Purchaser.
Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty
whatsoever in any of the cases as set forth below:
(a) Any defect of the Product caused by freight damage, modification, alteration, abuse, misuse, accident, incorrect
installation, disaster, faulty maintenance and/or improper repair by third party other than EIZO and Distributors;
(b) Any incompatibility of the Product due to possible technical innovations and/or regulations;
(c) Any deterioration of the sensor;
(d) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel
and/or backlight, etc. (e.g. changes in brightness, changes in brightness uniformity, changes in color, changes in
color uniformity, defects in pixels including burnt pixels, etc.);
(e) Any defect of the Product caused by external equipment;
(f) Any defect of the Product on which the original serial number has been altered or removed;
(g) Any defect of the Product caused by liquid leaking from battery;
(h) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g.
batteries, buttons, rotating parts, remote control, cables, User’s Manual, etc.); and
(i) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD
panel.
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss
in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of
such purchase when requesting services under the Warranty.
The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original
Warranty Period.
EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATION STORED IN ANY MEDIA OR ANY PART OF ANY PRODUCT RETURNED TO EIZO OR
DISTRIBUTORS FOR REPAIR.
EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO
THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE
PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN
IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND
DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/OR SALES.
30
LIMITED WARRANTY
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」,适用于在中华人民共和国销售的电子信息产品。标识中央的
数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项,在自制造日起算的年限内,不会
产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
• 有毒有害物质或元素的名称及含量
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
印刷电路板
×
○
○
○
○
○
机箱
○
○
○
○
○
○
液晶显示器
×
○
○
○
○
○
其他
×
○
○
○
○
○
○ :表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。
× :表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。
( 企业可在此处 , 根据实际情況对上表中打“×”的技术原因进行进一步说明 )
EIZO NANAO CORPORATION
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
Phone: +81 76 277 6792 Fax: +81 76 277 6793
Helmut-Grashoff-Straße 18, 41179 Mönchengladbach, Germany
Phone: +49 2161 8210210 Fax: +49 2161 8210150
中国苏州市苏州工业园区展业路8号中新科技工业坊5B
Phone: +86 512 6252 0100 Fax: +86 512 6252 1508
http://www.eizo.com
Copyright © 2010-2012 EIZO NANAO CORPORATION All rights reserved.
7th Edition-November, 2012
Printed in Japan.
00N0L595G1
(U.M-FDX1001T-AL)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement