Hardware Installation Guide

Hardware Installation Guide
X2 (雙)User’s Manual 3.5” SATA DUAL BAY ENCLOSURE External Enclosure Installation Guide
Hardware Installation Guide
☆ Please follow the instructions and make sure
your hard drive is successfully installed to the
external enclosure!
STEP1 :
Release the 4 screws then pull out the rear
panel and tray.
 Include
Hardware Installation Guide
HDD Formatting Guide
1
External Enclosure Installation Guide
STEP2: Place the first HDD into the tray. Push the
HDD to connect the SATA connector.
External Enclosure Installation Guide
STEP4: Screw the HDD on the tray both sides.
STEP5: Push the tray into the aluminum case.
STEP3: Place the second HDD into the tray. Push
the HDD to connect the SATA connector.
Screw the rear panel and enclosure together.
Note: Make sure all connectors are connected well.
2
3
External Enclosure Installation Guide
HDD Formatting Guide
External Enclosure Installation Guide
STEP2: Select “Disk Management” and you will
☆ This device can support JBOD& BIG Mode.
see your hard drives show
☆ JBOD:It enables each hard drive to be seen
separately as single drives, showing 2 HDD
capacities.
Note: Backup before formatting your HDD.
“Unallocated”.
Sample:750GB & 250GB hard drives.
JBOD Mode:
STEP1: Right-click on “My Computer” icon and
select the” Manage” column.
STEP3: Please refer to page 9.
5
4
External Enclosure Installation Guide
External Enclosure Installation Guide
BIG Mode:
☆BIG:
It concatenates a series of physical hard
drives as a single large volume; Hard drive A
and B are combined into a storage capacity
that is equal to the sum of each of the physical
hard drives A and B.
It is also possible to create a BIG volume using
only a single hard disk drive connected to SATA
connector 1, and then increase the storage
STEP1: Right -click “My Computer” icon and
select the “Manage” column.
capacity of the volume later by adding another
hard disk drive to SATA connector 2, and
pressing reset button. However, it is not possible
to expand an existing BIG volume by adding
another hard disk drive to SATA connector 2
and still preserve any existing data on that
volume.
6
7
External Enclosure Installation Guide
STEP2:
☆ Two brand-new HDD
- Select “Disk Management” and you will see
your External HDD shows “Not Initialized”.
☆ Two formatted HDDs
(These two HDDs have to be combined into
one disk.)
- Select “Disk Management” and you will see
your External HDD only shows one HDD,
another shows “Unallocated”.
External Enclosure Installation Guide
- Right-click the red-squared block and select
“Delete Partition”.
- Delete both HDDs’ partition then start to
format two HDD into one.
- You will see your External HDD shows “Not
Initialized”.
STEP3: Right-click the red-squared block and
select “Initialize Disk”.
8
9
External Enclosure Installation Guide
External Enclosure Installation Guide
STEP4: Press “OK” button to initialize HDD.
STEP6: The “New Partition Wizard” will appear.
Please follow the instruction of the wizard to
complete the partition.
STEP5: The external HDD will be showed
“Online”. Right-click the “Unallocated” block
and select “New Partition”.
10
11
External Enclosure Installation Guide
STEP7: When new partition is completed, the
external HDD will be recognized as a “New
Volume”.
- If you divided HDD into two partitions, format
two partitions separately.
- After two partitions are formatted
completely, you will see two healthy HDDs.
12
External Enclosure Installation Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising