Master Antenna Television System

Master Antenna Television System

Master Antenna

Television System

Everything you need to know about installing a Master

Antenna Television System with

Clipsal accessories.

PAGE

C O N T E N T S

4

T HE B A S I C S O F M AT V

7

8

S Y S T E M L O S S E S

IN T E R F E R E N C E A ND T R O UB L E S H O O T IN G

12

15

17

19

2 4

26

27

2 8

M AT V C A B L E

M AT V A M P L IF IE R S

D R O P TA P S

C O N NE C T I O N S O C K E T S , P L U G S A ND T E R M IN AT O R S

S P L I T T E R S

T O O L S

F L U S H M O UN T IN G C O N NE C T I O N A C C E S S O R IE S

2 0 0 0 S E R IE S

30

31

C 2 0 0 0 S E R IE S

35

37 he r i ta ge

H A N G - S E L L B L I S T E R P A C K S

32

A UD I O / V ID E O A C C E S S O R IE S

33

A N T E N N A M E C H A NI S M S

C O N NE C T I O N S O C K E T S A ND P L U G S

IND E X

The Basics of MATV

MATV stands for Master Antenna Television.

to receive signals from a single (Master) antenna, as opposed to individual an ten nas for each receiver.

The decibel indicates how many times greater or smaller a quantity is from a pre-established reference level. The relationship between dB levels is logarithmic, not linear. Therefore 40 dB is not twice as much as 20 dB, for example:

MATV systems are separated into two portions, the

‘Head End’ and the ‘Distribution System’. When these two portions are planned and engineered

appropriate installation tech niques, signals will be distributed without loss of signal qual i ty.

• 10 dB = 3.2 x reference level

• 20 dB = 10 x reference level

• 30 db = 32 x reference level

• 40 dB = 100 x reference level

• 50 dB = 316 x reference level

Any signal passing through system components, including the cable, will be attenuated (i.e., have its level diminished). The level of this attenuation is important, as it will be a factor in signal quality.

In the MATV industry, the zero reference level is 1,000 microvolts measured across 75 Ohms of impedance.

The reference level determines that a minimum signal of 1,000 microvolts is required to produce an acceptable picture.

Signal quality within the system is related to signal level, system noise and headroom. The system needs to maintain a low noise level and a high signal level.

However, the signal must not be too high, as this can overdrive the equipment.

The dB figure is represented as dBmV (a reference to 1 millivolt), or dBµV (a reference to 1 microvolt).

In order to simplify MATV design, the relationship between noise and signal levels is measured

(in Decibels).

MATV amplifier gains, cable losses, insertion losses and isolation values are all expressed in dB. To determine an amplifier output and any system losses, decibels are added and subtracted.

D E C I B E L S

The signal level received on a television antenna is meas ured in microvolts. Calculations in microvolts are difficult, there fore MATV calculations are carried

out in decibels.

The minimum signal for a good quality, noise free picture is typically stated as 0dBmV although most televisions will work with signals as small as -6dBmV.

Working to the 0dBmV lev el will provide a tolerance to slight signal variations. The signal level fed into a television should be kept below 20dBmV. Equipment is critical to maintain the maximum bandwidth.

Decibels are added and subtracted, as opposed to be ing multiplied and divided. The decibel is 1/10 of a bel and is derived from a formula originally used by telephone en gi neers.

4

M A S T E R A N T E NN A T E L E V ISION

M O D U L A T I O N

For audio and video signals to be transmitted using only a portion of the available bandwidth, they are modulated onto carrier signals within a fixed bandwidth. In Australia, the standard bandwidth is

7MHz, this is known as a channel.

The quality and strength of any signal received is de ter mined by the following:-

• Proximity to the transmission tower.

• Power of the transmitter.

• Quality of the transmission.

• Line of sight to the

If TVs or VCRs are tuned to a particular channel, it is not tuned into a single frequency, but a 7MHz band from which the audio and video information is retrieved.

• Interference from power lines.

• Directional characteristics and orientation of the an ten na.

• Level of gain of the antenna.

For analogue transmission in Australia the vision carrier is 1.25MHz above the lower frequency for a given channel’s bandwidth, with the primary audio approximately 5.5MHz above that. The secondary audio is approximately 242KHz above the primary audio.

A N T E N N A S E L E C T I O N

The antenna installation should provide at least 60 dB or 0dBmV of picture signal per channel at the amplifier input.

T H E M A T V H E A D E N D

The Head End of a MATV system usually consists of an antenna which receives broadcast signals, processing equipment to filter the signals and a distribution distribution losses. Antennas, am pli fi ers, taps, filters and attenuators are used in this portion of the system.

In strong signal areas this will be relatively easy to obtain. In weak signal areas a larger antenna

with a high gain will usu al ly be necessary. It may also be necessary to “stack” two or more antennas.

Stacking two antennas will provide an additional 3 dB of gain above the gain of a single antenna. Al though a pre-amplifier may be used, stacking before pream pli fi ca tion is preferable, as it delivers a cleaner signal to the system.

T H E M A T V A N T E N N A

The quality of TV reception can be no better than

the quality of the signal from the antenna. It is therefore vital to se lect the correct antenna for the intended location.

Antenna manufacturers produce geographic maps detailing preferred antenna types based on the geographic location. In addition, professional antenna

Antenna directivity is important. Directivity is a measure of how well an antenna will reject signals from any direction other than the front. The front-to-back ratio is one way of measuring an antenna’s directivity.

This is the ratio of the amount of signal received by the front of the antenna to the amount of signal received by the rear. A highly directional antenna will generally have a high front-to-back ratio.

placement and orientation.

5

S I G N A L S U R V E Y

Determining signal levels is one of the most

important steps in Head-End design and a signal survey before installing the system will avoid many potential problems.

Each outlet has a defined amount of signal level required, and there is a recommendation for maximum cable runs. Splitters and taps provide the same

signal quality to each outlet, as long as design recommendations are adhered to.

An antenna, several sections of mast, a field strength meter and a portable colour TV is the equipment required for a sig nal survey. The field strength meter measures the amount of sig nal received on each

If there is a poor signal received from the antenna, this same poor signal will be output to each of the TV outlets.To guarantee a good signal at each of the TV outlets, a good quality signal needs to be re ceived at the antenna.

much to overcome certain types of in ter fer ence. The portable TV allows the quality of the signal re ceived on each channel to be determined.

M A S T H E A D A M P L I F I E R S

In weak signal areas, it is often necessary to

amplify the signal before the distribution amplifier.

A T T E N U A T O R S

As there are many signals received by an antenna, there may be a wide variation in signal levels. In order to

ensure the same picture quality on all channels,

the signal levels may require equalisation to prevent the stronger sig nals from overriding the weaker ones.

Equalisation is achieved by using attenuators, acceptable quality. This is achieved using a specified amount.

Masterhead Amplifier.

It is important to choose a Masterhead Amplifier with a low noise figure. The noise figure of the Masterhead

Amplifier establishes the noise figure of the entire system, therefore the amplifier should always increase the signal more than it increases the noise.

M A T V D I S T R I B U T I O N

Attenuators can be either fixed or variable. They are either de signed for one specific attenuation level, or they are switchable so that the signals can be reduced in increments to the required level.

A well-designed distribution system is necessary

Attenuators reduce all signals that pass through by the same amount. Therefore, frequencies that need reducing need to be separated from the rest of the signals so that only the strong er signals are reduced. connected to the sys tem. The distribution of MATV is the role of a combination of splitters and taps.

level and maintain the correct impedance to each of the outputs. Calculation of losses as so ci at ed with splitters, drop taps and cable are required.

6

M A S T E R A N T E NN A T E L E V ISION

A M P L I F I E R S

Amplifiers increase the strength of signals

distribution system. The amplifier gain determines the level of signal increase, which should be high enough to provide an acceptable signal level to all tel e vi sions in the system.

the main line. The signal sent to each branch of the

system will be equal to the signal sent into the

splitter minus the splitter loss. That is, an input of

70 dBuV into a 2-way splitter will deliver a signal of 70 dBuV minus 3.5 dBuV splitter losses, or 66.5 dBuV to each branch of the Sys tem.

I N S E R T I O N L O S S

Although an amplifier’s gain is important, the output ca pa bil i ty is just as important. The amplifier’s specifications should be checked to ensure that the output level is sufficient to feed the system and that the strength of the input signal plus the gain of the am pli fi er doesn’t exceed the amplifiers rated out put ca pa bil i ty. Ex ceed ing the output capability will result overall sig nal de te ri o ra tion.

All tap-off devices inserted into the distribution system create signal loss. This type of loss is called insertion line, the insertion loss of each tap-off is subtracted from the signal carried by that line. When estimating total system losses, the insertion loss of each unit is added together to find the total in ser tion loss for that system. For example, if there are 10 tap-offs on the line, and each tap-off has an insertion loss of 0.5 dB, the total insertion loss is 5 dB.

System Loss es

For initial calculation, the tap-off values and the

C A B L E L O S S

A certain amount of signal will be lost as it travels through coaxial cable. This loss depends on the

type of cable used and the frequency of the signal being carried.

the amplifier and will in flu ence the final selection tap-off values.

I S O L A T I O N L O S S

Losses are greater at higher frequencies, the greatest loss occurring at channel 69 in UHF/ VHF systems. The cable loss should always be calculated at the highest received in the fu ture.

S P L I T T E R L O S S

When a two-way splitter is inserted in-line, the signal in each leg will be approximately 3.5 dBuV less than that of the main line. If a 4-way splitter is inserted inline, the signal in each leg is 6.5 dBuV less than that in

Each tap-off attenuates the signal by a specified number of dB to prevent one set from interfering with another. For example, if there is a 80 dBuV signal in the line, and a 20 dB drop tap is inserted in the line, the signal avail a ble at the tap-off would be 60 dBuV.

The 20dB loss is called ‘Thru’ Loss. In com put ing the total distribution system losses, calculate the Thru

Loss of the last tap-off only. Since the system design requires a minimum of 60 dBuV to each set, the lowest tap value should be used. For most MATV tap-offs this value is either 10 or 12dB.

7

Interference and

Trou ble Shoot ing

C R O S S M O D U L A T I O N

I N T E R F E R E N C E

A D J A C E N T C H A N N E L

I N T E R F E R E N C E

Cross modulation interference occurs in Broadband preamplifiers and distribution amplifiers when one or more signals (TV Channels) exceed the amplifiers rated output capability. This causes two or more signals (TV channels) to beat together resulting in the picture information of one chan nel appearing superimposed upon another. This in ter fer ence usually manifests itself as a windshield wiper effect or as a neg a tive image.

The windshield wiper effect is seen as the vertical or horizontal framing bars of the interfering channel appearing on the channel being viewed. The negative image appears as a superimposed image in the background of the picture on the channel being viewed.

Adjacent channel interference is caused by a strong signal from one channel overriding a weaker signal on an adjacent channel, producing a “herringbone” effect. An adjacent chan nel is one, which is next to another channel. For ex am ple, Channels 1 and 2, 7 and 8, 10 and 11 are adjacent channels. Channels 2 and 3 are not adjacent because there is a 15 MHz band between them. In addition, channels 5 and 6 are not ad ja cent because there is channel 5A between them.

Highly directional antennas and the use of filters and taps to attenuate and control the offending signals can usually eliminate this type of interference.

This interference can be eliminated by using a higher gain antenna to increase the weaker signals and by us ing attenuators to reduce the stronger signals.

It is always the strongest signal received that causes the interference and it does not normally show up on the in ter fer ing channel. The interfering signal may also be an FM signal or combination of FM and TV signals.

8

M A S T E R A N T E NN A T E L E V ISION

G H O S T I N G

A leading ghost sometimes occurs in strong signal areas when signal is picked up directly and displayed mi cro sec onds before the image is picked up by the antenna. Since 300-Ohm twin lead is unshielded and replaced with 75-Ohm coaxial cable. A balun should be placed as close as possible to the an ten na ter mi nals and the co ax i al cable connected to the TV set with a match ing transformer. Overpowering the unwanted signal can also eliminate this type of ghosting.

Poor installation tech niques can cause ghosting.

There are three common causes of ghosting:-

• Pickup of reflected signals by the antenna.

• Direct pickup of a signal by the TV or TV lead.

• Poor installation techniques.

of installation.

Not all signals reach an antenna directly. They can be reflected by buildings, mountains, or bodies of water. These reflected signals arrive at the antenna microseconds after the direct signal. This causes a second, fainter image to appear on the TV screen, just to the right of the main image. This is called a trailing ghost.

Poor crimping of F fittings can cause an impedance mismatch, and can result in reflected signals in the line.

Us ing a good crimping tool and making sure that all fit tings and splic es are correctly executed will help en sure trou ble free op er a tion of a system.

A trailing ghost can usually be eliminated by using a highly directional antenna or by stack ing

antennas. Changing the orientation of the antenna slightly may also eliminate the reception of the reflected signal.

A second image appearing to the left of the main

image is called a leading ghost. This is the result of the direct pickup of sig nal by the TV lead (when using

300-Ohm twin lead or a poor quality 700-Ohm lead), by the TV tuner itself or by the down lead from the antenna. ‘Ingress’ is the problem, the use of a Quad

Shielded lead eliminates this problem.

9

POWER LINE IN T ERF ERENCE

C A B L E

Power line interference is caused by radiation from a high voltage power line close to the antenna. To minimise this interference, the antenna should be located as far away from the power line as possible.

A balun should be used as close as possible to the antenna terminals to prevent direct pickup of radiation.

Video cabling should be cabled with RG-6, quad

shield, 75-Ohm coaxial cable. Coaxial cable is a con cen tric transmission line. It consists of a central conductor, a dielectric medium (such as polyethylene) which fixes the spac ing between the central con duc tor and an outer shield (such as copper braid or aluminum foil) and a weatherproof outer jacket (usually PVC).

Worn or cracked insulators on power lines can also cause this interference. If the interference shows up in ter mit tent ly (especially during wet weather), it may be due to cracked insulators on the power lines.

F-Type connectors for faster, eas i er installation.

Losses in coaxial cable are spec i fied as attenuation per metre of cable.

CO - CH A NNEL IN T ERF ERENCE

Co-channel interference is the result of two stations in dif fer ent locations operating on the same channel. It appears on a TV as two different pictures, as though one were placed on top of the other. The effect can be minimised by using a highly directional antenna, or, if necessary, by stacking an ten nas.

10

M A S T E R A N T E NN A T E L E V ISION

CATALOGUE

11

M A T V C A B L E

RG 59 Dual Shield MATV Cable

C O N S T R U C T I O N

.813mm/20AWG solid bare copper covered steel conductor with gas injected foam polyethylene insulation. 60% aluminium braid, foil tape, and Black

PVC jacket.

Available in a 100mm reel and 305mm reel in a box.

Sweep tested to 3GHz, SRL 25 dB minimum.

Rating: 80°C.

Catalogue

Number

Conductor Size

(mm)

(AWG) Cond.

Type

Shield Type

2B59D3B .813

20

Reel

Length (m)

Solid

BCCS

60% Aluminium

Braids

305

Nom.

O.D (m)

6.02

Insl. &

Core O. D(mm)

Vel. of

Prop (%)

3.66

83

Catalogue Number Description

2B59D1

2B59D3B

RG-59 COAX DUAL SHIELD

Pack Size

100m

RG-59 COAX DUAL SHIELD BOX 305m

RG6 Dual Shield MATV Cable

C O N S T R U C T I O N

1.02mm/18 AWG solid bare copper covered steel conductor with gas injected foam polyethylene insulation. 60% aluminium braid, foil tape, and a black PVC jacket. Available in a 100m reel and

305m reel in a box.

Sweep tested to 3GHz, SRL 25 dB minimum.

Rating: 80°C.

Catalogue

Number

Conductor

Size (mm)

(AWG) Cond.

Type

Shield Type

2B6D3B 1.02

18

Reel

Length (m)

Solid 60% Aluminium Braids 305

Nom.

O.D (m)

6.86

Insl. &

Core O. D (mm)

Vel. of

Prop (%)

4.57

85

Catalogue Number Description

2B6D1

2B6D3B

RG-6 COAX DUAL SHIELD

Pack Size

100m

RG-6 COAX DUAL SHIELD BOX 305m

12

M A S T E R A N T E NN A T E L E V ISION

M A T V C A B L E

RG6 Tri Shield MATV Cable

C O N S T R U C T I O N

1.02mm/18 AWG solid bare copper covered steel conductor with gas injected foam polyethylene insulation, DuoBond® II shield plus 60% aluminium braid, Black PVC

Jacket,100% Sweep Tested: 5MHz-1GHz,

SRL 20 dB minimum.

Rating: 80°C.

Catalogue

Number

Conductor Size

(mm)

2B6T3B 1.02

(AWG) Cond.

18

Type

Solid

BCCS

Shield

Type

Reel

Length (m)

60% Aluminium

Braids

305

Nom.

O.D (m)

6.86

Insl. &

Core O. D (mm)

4.57

Vel. of Prop

(%)

85

Catalogue Number Description

2B6T3B RG-6 COAX TRI SHIELD BOX

Pack Size Foxtel Approval No.

305m F10297

RG6 Quad Shield MATV Cable

C O N S T R U C T I O N

1.02mm/18 AWG solid bare copper covered steel conductor with gas injected foam polyethylene insulation. Foil tape, 60% aluminium braid, foil tape, and a black PVC jacket. Available in a 305m reel in a box.

Sweep tested to 3GHz, SRL 20 dB minimum.

Rating: 80°C.

Catalogue

Number

Conductor Size

(mm)

2B6T3B 1.02

(AWG) Cond.

Type

18 Solid

BCCS

Shield

Type

60% & 40%

Aluminium Braids

Reel

Length (m)

Nom.

O.D (m)

305 7.57

Insl. &

Core O. D (mm)

4.57

Vel. of

Prop (%)

85

Catalogue

Number

2B6Q1

2B6Q3

2B6Q3B

2B6Q3F

Description

RG-6 COAX QUAD SHIELD

RG-6 COAX QUAD SHIELD

RG-6 COAX QUAD SHIELD BOX

Pack Size Foxtel

Approval No.

100m F10298

305m

305m

RG-6 COAX QUAD SHIELD FLOODED 305m

F10298

F10298

F10299

Austar

Approval No.

A04752

A04750

A04751

A04749

13

M A T V C A B L E

RG11 Quad Shield MATV Cable

C O N S T R U C T I O N

1.63mm/14 AWG solid bare copper covered steel conductor with gas injected foam polyethylene insulation. Foil tape, 60% aluminium braid, foil tape, 40% aluminium braid and a black

PVC jacket. Available in 305m reels.

Sweep tested to 3GHz, SRL 25 dB minimum.

Rating: 80°C.

Catalogue

Number

Conductor Size

(mm)

2B11Q3 1.63

(AWG) Cond.

Type

14 Solid

BCCS

Shield

Type

60% & 40%

Aluminium Braids

Reel

Length (m)

305

Nom. O.D

(m)

Insl. & Core

O. D (mm)

Vel. of Prop

(%)

11.34

7.1

83

Catalogue

Number

2B11Q3

2B11Q3F

Description

RG-11 COAX QUAD SHIELD

Pack Size

305m

RG-11 COAX QUAD SHIELD FLOODED 305m

Foxtel

Approval No.

F10300

F10301

Austar

Approval No.

A04748

A04747

14

M A S T E R A N T E NN A T E L E V ISION

M A T V A M P L I F I E R S

3105MH24W

24dB Wide-band VHF/UHF Amplifier

F E A T U R E S A N D B E N E F I T S

Screw & Saddle masthead designed to amplify a single VHF &

UHF combined antenna.

Packed with a power supply.

VHF

UHF

Frequency

Range

Maximum

Gain(dB)

Inputs Noise Figure Gain Figure Current

(mA)

44-470

470-860

18

24 fixed

1 or comb

<3

<3

Tilt 14-10

NO

80

80

FM Trap

Option

NO

N/A

Pager

Option

NO

N/A

Output

Figure (dB)

105

105

3105MH34W

34dB Wide-band VHF/UHF Amplifier

F E A T U R E S A N D B E N E F I T S

Screw & Saddle masthead designed to amplify separate VHF

& UHF antennas or a combined VHF/UHF antenna.

Packed with a power supply.

Frequency

Range

VHF 44-230

UHF 520-860

Maximum

Gain(dB)

20-27

34

Inputs Noise

Figure

1,2 or comb

<3

<2.5

Gain Figure Current (mA) FM Trap Option

Tilt 12-10

10

90

90

-24

N/A

Pager

Option

-24

N/A

Output

Figure (dB)

108

108

3105MH38W

38dB Wide-band VHF/UHF Amplifier

F E A T U R E S A N D B E N E F I T S

Screw and saddle masthead designed to amplify separate

VHF & UHF antennas or a combined VHF/UHF antenna.

Packed with a power supply.

Frequency

Range

Maximum

Gain (dB)

VHF 44-230 20-28

UHF 470-860 24 fixed

Inputs Noise

Figure

1,2 or comb

<3

<2.5

Gain

Control

10

10

Current

(mA)

100

100

FM Trap

Option

33

N/A

Pager Option Output Figure (dB)

25 (Freq.Adj) 110

N/A 110

15

M A T V A M P L I F I E R S

3105MH34U

34dB UHF B

AND

A

MPLIFIER

F E A T U R E S A N D B E N E F I T S

Screw and saddle masthead designed to amplify a UHF antenna and diplex a separate VHF antenna or amplify the

UHF component of a combined antenna.

Packed with a power supply.

Frequency

Range

Maximum

Gain(dB)

VHF 44-230 -1

UHF 520-860 34

Inputs Noise Figure Gain Control Current (mA) FM Trap

Option

1,2 or comb

N/A

<2.5

N/A

10

85

85

NO

N/A

Pager

Option

NO

N/A

Output

Figure (dB)

108

108

3105SA2/10

2-Way Splitter Amplifier

F E A T U R E S A N D B E N E F I T S

A 2-way Splitter Amplifier designed for a separate VHF or

UHF antenna or combined antenna at the input.

Frequency Range Maximum Gain(dB) Inputs Noise Figure Gain Control Mains

VHF 44-470 12 1 <7 NO

Output Figure (dB)

230-240 VAC 100

UHF 470-860 12

1

<7 NO 230-240 VAC 100

3105DA30

30dB Distribution Amp with Gain & Equaliser

F E A T U R E S A N D B E N E F I T S

F-Type distribution amplifier designed for a separate VHF or UHF antenna or combined antenna at the input. Can be remotely powered to the output.

Packed with power supply.

Frequency

Range

VHF 44-470

UHF 44-470

Maximum

Gain (dB)

30

30

Inputs Noise

Figure

1

1

<7

<7

Gain

Control

10

10

Current

(mA)

170

170

Equalisation

(dB)

15-0

15-0

Output Figure

(dB)

112

112

16

M A S T E R A N T E NN A T E L E V ISION

3105T1/10

1-Way 10dB TAP Loss

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with -120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T1/15

1-Way 15dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T2/10

2-Way 10dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

D R O P T A P S

3105T1/12

1-Way 12dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

10

2.0

3.0

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T1/20

1-Way 20dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

16

1.3

2.2

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T2/12

2-Way 12dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

10

2.1

3.1

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

12

1.9

2.7

20

0.9

1.7

12

1.9

2.9

17

3105T2/15

2-Way 15dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T4/10

4-Way 10dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T4/15

4-Way 15dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

18

M A S T E R A N T E NN A T E L E V ISION

D R O P T A P S

3105T2/20

2-Way 20dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

16

1.5

2.3

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T4/12

4-Way 12dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

10

6.5

9.0

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

3105T4/20

4-Way 20dB TAP

F E AT UR ES A ND BENEF I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass one port

16

3.0

4.1

TAP LOSS (dB)

THROUGH LOSS 5-950MHz (dB)

THROUGH LOSS 950-2400MHz (dB)

Foxtel Approval Number: F10082-85/C

12

4.0

4.5

20

1.8

1.9

20

1.0

1.9

C O N N E C T I O N S O C K E T S , P L U G S A N D T E R M I N A T O R S

30TV75P

RG59 TV Antenna Connection Accessory

75 Ohm Coaxial Cable Plug

30TV75CS

RG59 TV Antenna Connection Accessory

75 Ohm TV Antenna Cord Line

Connection Socket

F E A T U R E S A N D B E N E F I T S

Features internal clamping screw and Flexible Cord Grip.

Screw secured cable signal carrying inner core ensures better connection and conductivity. Cord grip suits coaxial cables to a maximum diameter of 7.5mm.

F E A T U R E S A N D B E N E F I T S

Features Internal Clamping screw and Flexible Cord Grip.

Screw secured cable signal carrying inner core ensures better connection and conductivity. Cord Grip suits coaxial cables to a maximum diameter of 7.5mm.

30TV75C

TV Antenna Connection Accessory

75 Ohm Coax RG59 Cable Plug

Screw type

30TV75C1

TV Antenna Connection Accessory

75 Ohm Coax RG6 Cable Plug

No Crimping Tool Required

3105FTER

TV Antenna Connection Accessory

75 Ohm Terminator for Loop Circuit

Tap Socket

F E A T U R E S A N D B E N E F I T S

Terminator Device for unused sockets on Drop Taps,

Directional Couplers and Splitters. Provides impedance matching on any unused output sockets.

F E A T U R E S A N D B E N E F I T S

For solderless or screwed F type connections.

19

C O N N E C T I O N S O C K E T S , P L U G S A N D T E R M I N A T O R S

3105RG59F

RG59 F-Type Crimp Connector

Packet of 10

For use with Crimp Tool 3105CT611

3105RG6FT

RG6 F-Type Twist-On Connector

No Crimping Tool Required

3105RG59FT

RG59 F-Type Twist On Connector

Packet of 10

No Crimping Tool Required

3105FF-FF

F-Type Female to Female Coax Joiner

Packet of 10

3105RG6F

RG6 F-Type Connector

Suits Dual/Tri/Quad Shield RG6 Cables

Packet of 10

For Use with Crimp Tool 3105CT611

Foxtel Approval Number: F10179/C

3105PM-FF

PAL Male to F-Type Female Adaptor

Packet of 10

2 0

M A S T E R A N T E NN A T E L E V ISION

3105PF-FF

PAL Female to F-Type Female Adaptor

Packet of 10

C O N N E C T I O N S O C K E T S , P L U G S A N D T E R M I N A T O R S

3105BT2U

Balun Adaptor 300 to 75 Ohm

3105PF-FM

PAL Female to F-Type Male Adaptor

Packet of 10

3105BT1U

TV-Set Balun 75 to 300 Ohm

3105FMF

FM Filter (Indoor)

3105MBT3U

Antenna Balun with Screw Type Connector

21

C O N N E C T I O N S O C K E T S , P L U G S A N D T E R M I N A T O R S

3105MBT2U

Outdoor Balun with F-type Connector

3105RG59PFS

RG59 Metal PAL Female Plug

3105DPOUV

Outdoor Diplexer UHF/VHF with

F-Type Connectors.

3105PF-PF

PAL Female to PAL Female Coax Joiner

3105RG59PMS

RG59 Metal PAL Male Plug

3105PM-PM

PAL Male to PAL Male Coax Joiner

22

M A S T E R A N T E NN A T E L E V ISION

C O N N E C T I O N S O C K E T S , P L U G S A N D T E R M I N A T O R S

3105BNC59

BNC 3 Piece for RG-59

3105BNC6

BNC 3 Piece for RG-6

3105BNC-RCA

Coax Adaptor BNC to RCA

3105RG6PF

Coax PAL Socket for RG-6

3105RG6PM

Coax PAL Plug for RG-6

3105DPUV

Indoor Diplexer VHF/UHF with F-type Connectors

23

3105S2

2-Way Screw &

Saddle Splitter

S P L I T T E R S

3105S3

3-Way Screw &

Saddle Splitter

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 3.7

≤ 3.7

≤ 4

3105S4

4-Way Screw &

Saddle Splitter

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 7.5

≤ 7.6

≤ 8

3105SPFP3

3-Way F-Type Splitter

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

FREQUENCY RANGE (mhz)

5-40

40-1000

1000-1750

1750-2050

Foxtel Approval Number: F10082/C

INSERTION LOSS (dB)

8

7.5

9

11.5

2 4

M A S T E R A N T E NN A T E L E V ISION

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 5.7

≤ 6.3

≤ 6.5

3105SPFP2

2-way F-Type Splitter

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

Low loss 1750-2050

FREQUENCY RANGE (mhz)

5-40

40-1000

1000-1750

1750-2050

Foxtel Approval Number: F10082/C

3105SPFP4

4-Way F-Type Splitter

INSERTION LOSS (dB)

5.5

4.6

5.3

6.3

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

Low loss 1750-2050

FREQUENCY RANGE (mhz)

5-40

40-1000

1000-1750

1750-2050

Foxtel Approval Number: F10082/C

INSERTION LOSS (dB)

8

8.5

10.5

11.5

3105SPF2

2-Way F-Type Splitter

1 Leg Power Pass

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

Low loss 1750-2050

S P L I T T E R S

3105SPF3

3-Way F-Type Splitter

1 Leg Power Pass

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

Low loss 1750-2050

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

1750-2050

INSERTION LOSS (dB)

≤ 3

≤ 3.5

≤ 4.4

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 5.5

≤ 6.1

≤ 6.3

3105SPF4

4-Way F-Type Splitter

1 Leg Power Pass

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with –120dB RFI

Power-pass all ports

Low loss 1750-2050

3105SPF6

6-Way F-Type Splitter

1 Leg Power Pass

F E A T U R E S A N D B E N E F I T S

Nickel-plated zinc die-cast housings

High shielding with - 120dB RFI

Power-pass all ports

Low loss 1750-2050

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 6.9

≤ 7.5

≤ 7.8

FREQUENCY RANGE (mhz)

5-45

46-470

471-860

INSERTION LOSS (dB)

≤ 9.2

≤ 10.2

≤ 10.7

25

T O O L S

3105CS6

RG6 and RG59 Cable Stripper

3105CS11

RG11 Cable Stripper

F E A T U R E S A N D B E N E F I T S

Cable preparation tool for RG6 and RG59 cable.

For use with 0.360 size F-type connector.

F E A T U R E S A N D B E N E F I T S

Cable preparation tool for RG11 cable.

For use with 0.470 size F-type connector.

26

M A S T E R A N T E NN A T E L E V ISION

F L U S H M O U N T I N G C O N N E C T I O N A C C E S S O R I E S

31VTVA

Standard TV Antenna Socket Flush

Mounting 300 Ohm TV Socket

32TVACFF

F-Type Connectors, One with 3KV AC

Isolation Two Gang Standard Flush Plate

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket fitted to 31VH Plate.

300 Ohm TV Antenna Flush Socket

70 x 115mm Plate.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

FTA outlet not suitable for applications over 1000Mhz.

31VTV75

Standard TV Antenna Socket Flush

Mounting 75 Ohm Coaxial TV Socket

32TVFF

F-Type Connector

Two Gang Standard Flush Plate

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket fitted to 31VH Plate.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

FTA outlet not suitable for applications over 1000Mhz.

31TVF

F-Type Connector, Single Standard Flush

Plate marked “Pay TV”

32TVSF

One F-Type, and One Solderless 75 Ohm

Connector Two Gang Standard Flush Plate

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

Plate size 115x73mm.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

F-Type Connector provides minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting. The solderless connector features a terminal with screw for the inner core and saddle clamp for outer shield.

FTA outlet not suitable for applications over 1000Mhz.

27

FLUSH MOUNTING CONNECTION ACCESSORIES

31VTV75ACF

Standard TV Antenna Socket

Flush Mounting 75 Ohm TV Socket with

3kVac Isolation

2 0 0 0 S E R I E S

2031VTV05

2000 Series TV Outlet Plate with 12mm

Hole to suit 75 Ohm Coaxial TV Antenna

Socket Mechs

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket fitted to 31VH Plate.

Not suitable for applications over 1000Mhz.

31VTV75F

Standard TV Antenna Socket

Flush Mounting 75 Ohm TV Socket with

F-Type Connection

F E A T U R E S A N D B E N E F I T S

Dimensions 116x76mm.

Mounting centres 84mm.

Recommended for mounting to 164 series Wall Box.

Can be used with all Standard Pattern Mounting accessories.

Not suitable for applications over 1000Mhz.

2031VTV75

2000 Series TV Antenna Socket Flush

Mounting 75 Ohm Coaxial Socket

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket fitted to 31VH Plate.

Not suitable for applications over 1000Mhz.

32VTV75FM

Standard TV Antenna Socket

Flush Mounting TV - FM Splitter

F E A T U R E S A N D B E N E F I T S

Dimensions 116x76mm.

Mounting centres 84mm. Suits Standard Mounting accessories.

Recommended for use with 164 Wall Box.

Can be used with all Standard Mounting accessories.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket fitted to 31VH Plate.

TV-FM Splitter fitted to Standard Flush Plate

Not suitable for applications over 1000Mhz.

2 8

M A S T E R A N T E NN A T E L E V ISION

2031VTV75ACF

2000 Series TV Antenna Socket Flush

Mounting 75 Ohm TV Socket with

3kVac Isolation

2 0 0 0 S E R I E S

2032VTV75FM

2000 Series TV Antenna Socket Flush

Mounting Dual 75 Ohm

TV - FM Splitter

F E A T U R E S A N D B E N E F I T S

Dimensions 116x76mm. Mounting centres 84mm.

Suits Standard Mounting accessories. Super low loss F type screw in cable connection. Recommended for use with

164 Wall Box. Can be used with all Standard Mounting accessories.

Not suitable for applications over 1000Mhz.

2031VTV75F

2000 Series TV Antenna Socket Flush

Mounting 75 Ohm TV Socket with

F-Type Connection

F E A T U R E S A N D B E N E F I T S

Dimensions 116x76mm. Mounting centres 84mm. Suits

Standard Mounting accessories. Super low loss F type cable connection. Maximises TV and FM radio signals, for improved reception in poor reception areas.

Not suitable for applications over 1000Mhz.

2031TVF

F-Type Connector Single 2000 Series

Flush Plate Marked “Pay TV”

F E A T U R E S A N D B E N E F I T S

Dimensions 116x76mm. Mounting centres 84mm. Suits

Standard Mounting accessories. Super low loss F type cable connection. Recommended for use with 164 Wall Box.

Can be used with all Standard Mounting accessories.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

Plate size 116x76mm.

2032TVACFF

F-Type Connectors, One with 3KV AC

Isolation Two Gang 2000 Series Flush Plate

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

FTA outlet not suitable for applications over 1000Mhz.

29

C 2 0 0 0 S E R I E S

2032TVFF

F-Type Connector

Two Gang 2000 Series Flush Plate

P 2 0 0 0 S E R I E S

P2031VTV75

Prestige P2000 Series TV Antenna Socket

Outlet Flush 75 Ohm Coaxial Socket

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

FTA outlet not suitable for applications over 1000Mhz.

2032TVSF

One F-Type, and One Solderless 75 Ohm

Connector Two gang 2000 Series

Flush Plate

F E A T U R E S A N D B E N E F I T S

Dimensions 116x73mm. Mounting centres 84mm. Suits

Standard Mounting accessories. Recommended for use with

164 Wall Box.

Not suitable for applications over 1000Mhz.

P30TV75MS

Prestige Series TV Antenna Mechanism

75 Ohm Socket

F E A T U R E S A N D B E N E F I T S

F-Type Connector provides minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting. The solderless connector features a terminal with screw for the inner core and saddle clamp for outer shield.

FTA outlet not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

75 Ohm Coaxial TV Connection. Socket Mechanism Screw

Connection - Solderless Type To Suit Prestige Grids.

Not suitable for applications over 1000Mhz.

C2031VTV75G

C2000 Series Grid Assembly Flush

Mounting 75 Ohm Coaxial TV Socket

F E A T U R E S A N D B E N E F I T S

Dimensions 113x73mm. Mounting centres 84mm. Suitable for mounting to standard pattern mounting accessories. Suits

C2031C series cover only.

Not suitable for applications over 1000Mhz.

30

M A S T E R A N T E NN A T E L E V ISION

H E R I T A G E

1920STV75

Heritage Range Shallow Surface Mounted

75 Ohm TV Outlet with Brass Cover

1920SRTV75

Heritage Range Shallow Surface Mounted

75 Ohm TV Outlet with Ribbed Brass Cover

F E A T U R E S A N D B E N E F I T S

Dimensions - Cover 53mm diameter x 25mm high.

Base projection 13mm.

The socket is designed to accommodate solid core conductor coaxial cables with insulation (dielectric) up to 5mm diameter. eg RG59/u, RG6/u, TM3502, SSA37, etc. cables.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Dimensions - Cover 54mm diameter x 25mm high.

Base projection 13mm.

The socket is designed to accommodate solid core conductor coaxial cables with insulation (dielectric) up to 5mm diameter. eg RG59/u, RG6/u,TM3502, SSA37 etc. cables.

Not suitable for applications over 1000Mhz.

H A N G S E L L - B L I S T E R P A C K S

BL1920STV75

Heritage Range Shallow Surface Mounted

Blister Packed 75 Ohm TV Outlet

BL1920SRTV75

Heritage Range Shallow Surface Mounted

Blister Packed 75 Ohm TV Outlet with

Ribbed Cover

F E A T U R E S A N D B E N E F I T S

Dimensions - Cover 53mm diameter x 25mm high.

Base projection 13mm.

The socket is designed to accommodate solid core conductor coaxial cables with insulation (dielectric) up to 5mm diameter. eg RG59/u, RG6/u TM3502, SSA37, etc. cables.

Not suitable for applications over 1000Mhz.

F E A T U R E S A N D B E N E F I T S

Dimensions - Cover 54mm diameter x 25mm high.

Base projection 13mm.

The socket is designed to accommodate solid core conductor coaxial cables with insulation (dielectric) up to 5mm diameter. eg RG59/u, RG6/u, TM3502, SSA37 etc. cables.

Not suitable for applications over 1000Mhz.

31

A U D I O / V I D E O A C C E S S O R I E S

3105AVL318

1.8m Length 3RCA to 3RCA Lead

3105SC-6RCA

Scart - 6 RCA Lead

F E A T U R E S A N D B E N E F I T S

Stereo Audio / Video lead with RCA connectors

3105SC-SC

Scart - Scart Lead

32

M A S T E R A N T E NN A T E L E V ISION

A N T E N N A M E C H A N I S M S

3105FL118FB

PAL Male to Female Fly-Lead (Black)

3105FL118FBQ

PAL Male to Female Fly-Lead Quad Shield

(Black)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG 59 cable and

PAL male to PAL female fly-lead.

3105FL118MB

PAL Male to PAL Male Fly Lead (Black)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG6 Quad Shield cable and

PAL male to PAL female fly-lead.

3105FL118FW

PAL Male to Female Fly-Lead (White)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG 59 cable and

PAL male to PAL male fly-lead.

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG 59 cable and

PAL male to PAL female fly-lead.

3105FL118FWQ

PAL Male to Female Fly-Lead Quad Shield

(White)

3105FL118MW

PAL Male to PAL Male Fly Lead (White)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG6 Quad Shield cable and

PAL male to PAL female fly-lead.

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG 59 cable and

PAL male to PAL male fly-lead.

33

A N T E N N A M E C H A N I S M S

3105FL118MBQ

PAL Male to PAL Male Fly Lead Quad Shield

(Black)

3105FL150MB

PAL Male to PAL Male Fly-Lead (Black)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG 6 Quad Shield cable and

PAL male to PAL male fly-lead.

3105FL318MB

F-Type to PAL Male Fly Lead (Black)

F E A T U R E S A N D B E N E F I T S

5m length lead with RG 59 cable and

PAL male to PAL male fly-lead.

3105FL118MWQ

PAL Male to PAL Male Fly-Lead Quad

Shield (White)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG59 cable and F-Type to PAL male fly-lead

3105FL150MW

5m Length PAL Male Fly-Lead (White)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG6 Quad Shield cable and

PAL male to PAL male fly-lead.

3105FL318MW

RG59 PAL to F-type Lead (White)

F E A T U R E S A N D B E N E F I T S

5m length lead with RG59 cable and

PAL male to PAL male fly-lead

3 4

M A S T E R A N T E NN A T E L E V ISION

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG59 cable and

F-type to PAL male lead.

A N T E N N A M E C H A N I S M S

3105FL318MBQ

F-type to PAL Male Fly Lead Quad Shield

(Black)

3105FL318MWQ

F-type to PAL Male Fly Lead Quad Shield

(White)

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG6 Quad Shield cable and F-type to

PAL male fly-lead.

F E A T U R E S A N D B E N E F I T S

1.8m length lead with RG6 Quad Shield cable and F-type to

PAL male fly-lead.

C O N N E C T I O N S O C K E T S A N D P L U G S

30PFM

F-Type Connector Mechanism Only, Suits

All 30 Series Apertures

30TV75MF

TV Antenna Connection Accessory

75 Ohm TV Antenna Socket with

F-Type Connection

F E A T U R E S A N D B E N E F I T S

Mating connections screw into the connector to provide minimum signal loss and optimum impedance matching to substantially reduce reflections and ghosting.

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket with F-Type Connection to suit 30 Series Plate Apertures.

Not suitable for satellite services.

35

30TV75M

TV Antenna Connection Accessory

75 Ohm TV Antenna Socket

Fits 30 Series Plates

C O N N E C T I O N S O C K E T S A N D P L U G S

30TV75MACF

TV Antenna Connection Accessory 75 Ohm

TV Antenna Socket with 3kV AC Isolation

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket to suit 30 Series

Plate Apertures.

Not suitable for satellite services.

F E A T U R E S A N D B E N E F I T S

Insulated 75 Ohm Coaxial TV Socket with F-Type Connection

& 3kV AC Isolation to suit 30 Series Plate Apertures.

Not suitable for satellite services.

30TV75MS

TV Antenna Connection Accessory 75 Ohm

TV Antenna Socket - Screw Fixed Solderless

F E A T U R E S A N D B E N E F I T S

75 Ohm Coaxial TV Connection Socket Screw Connections,

“SOLDERLESS TYPE” to fit 30 Series Plate Aperture.

Not suitable for satellite services.

36

M A S T E R A N T E NN A T E L E V ISION

INDEX

CATALOGUE NUMBER PAGE CATA L OGUE NUMBER PAGE

BL1920SRTV75 31

BL1920STV75 31

C2031VTV75G 30

P2031VTV75 30

P30TV75MS 30

1920SRTV75 31

1920STV75 31

2031TVF 29

2031VTV05 28

2031VTV75 28

2031VTV75ACF 29

2031VTV75F 29

2032TVACFF 29

2032TVFF 30

2032TVSF 30

2032VTV75FM 29

2B11Q3 14

2B11Q3F 14

2B59D1 12

2B59D3B 12

2B6D1 12

2B6D3B 12

2B6Q1 13

2B6Q3 13

2B6Q3B 13

2B6Q3F 13

2B6T3B 13

30PFM 35

30TV75C 19

30TV75C1 19

30TV75CS 19

30TV75M 36

30TV75MACF 36

30TV75MF 35

30TV75MS 36

30TV75P 19

3105AVL318 32

3105BNC59 23

3105BNC6 23

3105BNC-RCA 23

3105BT1U 21

3105BT2U 21

3105CS11 26

3105CS6 26

3105CT611 26

3105DA30 16

3105DPOUV 22

3105DPUV 23

3105FF-FF 20

3105FL118FB 33

3105FL118FBQ 33

3105FL118FW 33

3105FL118FWQ 33

3105FL118MB 33

3105FL118MBQ 34

3105FL118MW 33

3105FL118MWQ 34

3105FL150MB 34

3105FL150MW 34

3105FL318MB 34

3105FL318MBQ 35

3105FL318MW 34

3105FL318MWQ 35

3105FM 21

3105FTER 19

3105MBT2U 22

3105MBT3U 21

3105MH24W 15

3105MH34U 16

3105MH34W 15

3105MH38W 15

3105PF-FF 21

3105PF-FM 21

3105PF-PF 22

37

INDEX

CATA L OGUE NUMBER PAGE CATA L OGUE NUMBER PAGE

3105PM-FF 20

3105PM-PM 22

3105RG59F 20

3105RG59FT 20

3105RG59PFS 22

3105RG59PMS 22

3105RG6F 20

3105RG6FT 20

3105RG6PF 23

3105RG6PM 23

3105S2 24

3105S3 24

3105S4 24

3105SA2/10 16

3105SC-6RCA 32

3105SC-SC 32

3105SPF2 25

3105SPF3 25

3105SPF4 25

3105SPF6 25

3105SPF8 26

3105SPFP2 24

3105SPFP3 24

3105SPFP4 24

3105T1/10 17

3105T1/12 17

3105T1/15 17

3105T1/20 17

3105T2/10 17

3105T2/12 17

3105T2/15 18

3105T2/20 18

3105T4/10 18

3105T4/12 18

3105T4/15 18

3105T4/20 18

31TVF 27

31VTV75 27

31VTV75ACF 28

31VTV75F 28

31VTVA 27

32TVACFF 27

32TVFF 27

32TVSF 27

32VTV75FM 28

38

M A S T E R A N T E NN A T E L E V ISION

AUSTRALIA

Clipsal Australia Pty Ltd

Tel: +618 8269 0511

Fax: +618 8340 1724

[email protected]

CHINA

Clipsal China Ltd

Tel: +86 755 8237 5959

Fax: +86 755 8237 5995

[email protected]

HONG KONG

Clipsal Datacom Asia Limited

Tel: +852 2487 0261

Fax: +852 2480 5865

[email protected]

INDIA

Schneider Electric India Pvt Ltd

Tel: +91 11 5159 0000

Fax: +91 11 5167 8010

www.schneider-electric.co.in

INDONESIA

PT Clipsal Graha Nusa

Tel: +62 21 630 6430

Fax: +62 21 631 6279

[email protected]

KOREA

Clipsal Datacoms Korea Co Ltd

Tel: +82 2 546 3335

Fax: +82 2 546 3393

[email protected]

MALAYSIA

Clipsal Datacomms (M) Sdn Bhd

Tel: +603 7665 3555

Fax: +603 7665 3155

[email protected]

NEW ZEALAND

Clipsal Industries (NZ) Limited

Tel: +64 9 576 3403

Fax: +64 9 576 1015

[email protected]

PAKISTAN

Clipsal Pakistan (Pvt) Ltd

Tel: +92 21 506 7278

Fax: +92 21 506 3369

[email protected]

PHILIPPINES

Clipsal Datacomm Asia Limited

Tel: +632 683 0275-78

Fax: +632 683 0279

[email protected]

SINGAPORE

Clipsal Datacomms (S) Pte Ltd

Tel: +65 6415 3232/3233

Fax: +65 6415 3289

[email protected]

SOUTH AFRICA

Clipsal South Africa (Pty) Ltd

Tel : +27 11 314 5200

Fax: +27 11 314 5294

[email protected]

TAIWAN

Clipsal (Taiwan) Co., Ltd

Tel: +886 2 255 83456

Fax: +886 2 255 83000

[email protected]

THAILAND

Clipsal (Thailand) Co Ltd

Tel:+662 952 5338-42

Fax: +662 952 5337

[email protected]

UNITED ARAB EMIRATES

Clipsal Middle East

Tel: +971 6 5570 777

Fax: +971 6 5570 333

[email protected]

UNITED KINGDOM

Clipsal Integrated Systems UK

Tel: +44 (0) 1628 508 530

Fax: +44 (0) 1628 508 565

[email protected]

VIETNAM

Clipsal - VTEC

Tel: +848 856 3002

Fax: +848 856 3006

[email protected]

O/N 5902 NOV 04/02

CLIPADV 8511

Clipsal Datacomms reserves the right to change specifications, modify designs and discontinue items without incurring obligation and whilst every effort is made to ensure that descriptions, specifications and other information in this catalogue are correct, no warrant is given in respect thereof and the company shall not be liable for any error therein.

© 2003/04 Clipsal Datacomms

www.clipsaldatacomms.com

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement