ASROCK | 970 Extreme3 R2.0 | Installation guide | Asrock 970 Extreme3 R2.0

Asrock 970 Extreme3 R2.0
Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation
by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this guide are furnished for informational use
only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may
appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its
directors, officers, employees, or agents be liable for any indirect, special, incidental, or
consequential damages (including damages for loss of profits, loss of business, loss of
data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
English
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published May 2013
Copyright©2013 ASRock INC. All rights reserved.
ASRock 970 Extreme3 R2.0 Motherboard
1
Motherboard Layout
CPU_FAN2
CPU_FAN1
Optical
SPDIF
USB 2.0
T: USB2
B: USB3
DDR3 2100+
eSATA3
SOCKET AM3b
RJ-45 LAN
USB 2.0
T: USB0
B: USB1
AM3+ 140W CPU
USB 3.0
T: USB0
B: USB1
38
USB3_2_3
Center:
FRONT
Top:
LINE IN
Bottom:
MIC IN
Front USB 3.0
Top:
SIDE SPK
Center:
REAR SPK
Bottom:
CTR BASS
37
AMD
970
Chipset
PCIE1
FSB800
Coaxial
SPDIF
ATX12V1
LAN
PHY
DDR3_A2 (64 bit, 240-pin module)
CHA_FAN3
8
7
DDR3_B2 (64 bit, 240-pin module)
6
DDR3_B1 (64 bit, 240-pin module)
PS2
Mouse
PS2
Keyboard
5
4
Support 8-Core CPU
3
FSB800
2
DDR3_A1 (64 bit, 240-pin module)
1
9
10
PWR_FAN1
11
36
PCIE2
35
X
CMOS
BATTERY
PCIE3
Fast LAN
34
12
AMD
SB950
Chipset
AUDIO
CODEC
PCIE4
CHA_FAN1
13
970 Extreme3
Super
I/O
X
PCI1
14
Fast RAM
X
RoHS
ErP/EuP Ready
SPEAKER1
PLED1
1
1
Fast USB
CLRCMOS1
15
32Mb
BIOS
CHA_FAN2
1
SATA3_3
SATA3_1
SATA3_4
SATA3_2
PCI2
33
USB_8_9
PLED PWRBTN
USB_4_5
USB_6_7
SATA3_5
IR1
HDMI_SPDIF1
1
1
1
16
17
PANEL 1
COM1
HD_AUDIO1
1
1
1
1
1
HDLED
1
RESET
18
CIR1
32 31
1
2
3
4
5
6
7
8
English
9
10
11
12
13 14
15
16
17
18
2
30
29
28
ATX 12V Power Connector (ATX12V1)
Chassis Fan Connector (CHA_FAN3)
AM3+ CPU Socket
CPU Heatsink Retention Module
CPU Fan Connector (CPU_FAN2)
CPU Fan Connector (CPU_FAN1)
2 x 240-pin DDR3 DIMM Slots (Dual Channel: DDR3_A1, DDR3_B1) 2 x 240-pin DDR3 DIMM Slots
(Dual Channel: DDR3_A2, DDR3_B2)
ATX Power Connector (ATXPWR1) Power Fan Connector (PWR_FAN1)
Northbridge Controller Chassis Fan Connector (CHA_FAN1)
Southbridge Controller
SPI Flash Memory (32Mb)
Chassis Fan Connector (CHA_FAN2)
SATA3 Connector (SATA3_3)
SATA3 Connector (SATA3_1)
SATA3 Connector (SATA3_2)
27 26 25 24 23 22 21 20 19
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
SATA3 Connector (SATA3_4)
SATA3 Connector (SATA3_5)
Clear CMOS Jumper (CLRCMOS1)
Power LED Header (PLED1)
System Panel Header (PANEL1)
Chassis Speaker Header (SPEAKER1)
Consumer Infrared Module Header (CIR1)
USB 2.0 Header (USB_4_5)
USB 2.0 Header (USB_6_7)
USB 2.0 Header (USB_8_9)
Infrared Module Header (IR1)
COM Port Header (COM1)
HDMI_SPDIF Header (HDMI_SPDIF1)
Front Panel Audio Header (HD_AUDIO1)
PCI Slots (PCI1-2)
PCI Express 2.0 x16 Slot (PCIE4)
PCI Express 2.0 x1 Slot (PCIE3)
PCI Express 2.0 x16 Slot (PCIE2)
PCI Express 2.0 x1 Slot (PCIE1)
USB 3.0 Header (USB3_2_3)
ASRock 970 Extreme3 R2.0 Motherboard
I/O Panel
1
* 2
3
4
5
6
7
** 8
PS/2 Mouse Port (Green) LAN RJ-45 Port
USB 2.0 Ports (USB23)
Side Speaker (Gray)
Rear Speaker (Black)
Central / Bass (Orange)
Line In (Light Blue)
Front Speaker (Lime)
9
10
*** 11
12
13
14
15
Microphone (Pink) USB 3.0 Port (USB01)
eSATA3 Connector
USB 2.0 Ports (USB01)
Optical SPDIF Out Port
Coaxial SPDIF Out Port
PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
LAN Port LED Indications
Activity/Link LED
Status
Description
Off
No Link
Blinking Data Activity
On
Link
Status
Off
Orange
Green
SPEED LED
Description
ACT/LINK SPEED
LED
LED
10Mbps connection
100Mbps connection
1Gbps connection
LAN Port
** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Central / Bass
(No. 6)
--
--
V
V
ASRock 970 Extreme3 R2.0 Motherboard
Side Speaker
(No. 4)
---V
English
Audio Output Channels Front Speaker Rear Speaker
(No. 8)
(No. 5)
2
V
--
4
V
V
6
V
V
8
V
V
3
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “Mixer” tool on your system.
Please select “Mixer ToolBox”
, click “Enable playback multi-streaming”, and click “ok”.
Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA
Audio 2nd output” to use front panel audio.
*** eSATA3 connector supports SATA Gen3 in cable 1M.
English
4
ASRock 970 Extreme3 R2.0 Motherboard
1. Introduction
Thank you for purchasing ASRock 970 Extreme3 R2.0 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It
delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. More detailed information of the motherboard can be found
in the user manual presented in the Support CD.
Because the motherboard specifications and the BIOS software might
be updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may
find the latest VGA cards and CPU support lists on ASRock website as
well. ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp
1.1 Package Contents
ASRock 970 Extreme3 R2.0 Motherboard (ATX Form Factor)
ASRock 970 Extreme3 R2.0 Quick Installation Guide
ASRock 970 Extreme3 R2.0 Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield
ASRock Reminds You...
English
To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM
/ VistaTM 64-bit, it is recommended to set the BIOS option in Storage
Configuration to AHCI mode. For the BIOS setup, please refer to the “User
Manual” in our support CD for details.
ASRock 970 Extreme3 R2.0 Motherboard
5
1.2 Specifications
Platform
CPU
Chipset
Memory
Expansion Slot
Audio
English
LAN
6
- ATX Form Factor
- ASRock DuraCap (2.5 x longer life time) (100%
Japan-made high-quality Conductive Polymer Capacitors)
- Support for Socket AM3+ processors
- Support for Socket AM3 processors: AMD PhenomTM II X6 / X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 / Sempron processors
- Supports 8-Core CPU
- Supports UCC feature (Unlock CPU Core) (see CAUTION 1)
- Digi Power Design
- 4 + 1 Power Phase Design
- Supports CPU up to 140W
- Supports AMD’s Cool ‘n’ QuietTM Technology
- FSB 2400 MHz (4.8 GT/s)
- Supports Untied Overclocking Technology
- Supports Hyper-Transport 3.0 (HT 3.0) Technology
- Northbridge: AMD 970
- Southbridge: AMD SB950
- Dual Channel DDR3 Memory Technology
- 4 x DDR3 DIMM slots
- Support DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/
1333/1066/800 non-ECC, un-buffered memory
(see CAUTION 2)
- Max. capacity of system memory: 32GB (see CAUTION 3)
- 2 x PCI Express 2.0 x16 slots
(PCIE2 @ x16 mode; PCIE4 @ x4 mode)
- 2 x PCI Express 2.0 x1 slots
- 2 x PCI slots
- Supports AMDTM Quad CrossFireXTM and CrossFireXTM
- 7.1 CH HD Audio with Content Protection
(Realtek ALC892 Audio Codec)
- Premium Blu-ray audio support
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supports Wake-On-LAN
- Supports LAN Cable Detection
- Supports Energy Efficient Ethernet 802.3az
- Supports PXE
ASRock 970 Extreme3 R2.0 Motherboard
SATA3
USB 3.0
Connector
BIOS Feature
I/O Panel
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Coaxial SPDIF Out Port
- 1 x Optical SPDIF Out Port
- 4 x Ready-to-Use USB 2.0 Ports
- 2 x Ready-to-Use USB 3.0 Ports
- 1 x eSATA3 Connector
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/
Line in/Front Speaker/Microphone
- 5 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 5 and RAID 10), NCQ, AHCI and "Hot Plug"
functions
- 2 x Rear USB 3.0 ports by Etron EJ188H, support USB
1.1/2.0/3.0 up to 5Gb/s
- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports) by
Etron EJ188H, supports USB 1.1/2.0/3.0 up to 5Gb/s
- 5 x SATA3 6.0Gb/s connectors
- 1 x IR header
- 1 x CIR header
- 1 x COM port header
- 1 x HDMI_SPDIF header
- 1 x Power LED header
- 2 x CPU Fan connectors (1 x 4-pin, 1 x 3-pin)
- 3 x Chassis Fan connectors (1 x 4-pin, 2 x 3-pin)
- 1 x Power Fan connector (3-pin)
- 24 pin ATX power connector
- 8 pin 12V power connector
- Front panel audio connector
- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
- 1 x USB 3.0 header (supports 2 USB 3.0 ports)
- 32Mb AMI UEFI Legal BIOS with GUI support
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- CPU, VCCM, NB, SB Voltage Multi-adjustment
ASRock 970 Extreme3 R2.0 Motherboard
English
Rear Panel I/O
7
Support CD
- Drivers, Utilities, AntiVirus Software (Trial Version),
CyberLink MediaEspresso 6.5 Trial, Google Chrome
Hardware Monitor
OS
Certifications
Browser and Toolbar
- CPU Temperature Sensing
- Chassis Temperature Sensing
- CPU/Chassis/Power Fan Tachometer
- CPU/Chassis Quiet Fan
- CPU/Chassis Fan Multi-Speed Control
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
- Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit / XP / XP 64-bit compliant (see CAUTION 4)
- FCC, CE, WHQL
- ErP/EuP Ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com
WARNING
Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking
Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components
and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by
overclocking.
English
8
ASRock 970 Extreme3 R2.0 Motherboard
CAUTION!
English
1. ASRock UCC (Unlock CPU Core) feature simplifies AMD CPU
activation. As long as a simple switch of the UEFI option “ASRock UCC”, you can unlock the extra CPU core to enjoy an
instant performance boost. When UCC feature is enabled, the
dual-core or triple-core CPU will boost to the quad-core CPU,
and some CPU, including quad-core CPU, can also increase L3
cache size up to 6MB, which means you can enjoy the upgrade
CPU performance with a better price. Please be noted that UCC
feature is supported with AM3/AM3+ CPU only, and in addition,
not every AM3/AM3+ CPU can support this function because
some CPU’s hidden core may be malfunctioned.
2. Whether 2100/1866/1800/1600MHz memory speed is supported depends on the AM3/AM3+ CPU you adopt. If you want
to adopt DDR3 2100/1866/1800/1600 memory module on this
motherboard, please refer to the memory support list on our
website for the compatible memory modules. Non OC mode’s
DDR3 1866 is supported by AM3+ CPU.
ASRock website: http://www.asrock.com
3. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage under Windows® 8 / 7 / VistaTM / XP. For Windows® 64-bit OS with
64-bit CPU, there is no such limitation.
4. ASRock XFast RAM is not supported by Microsoft® Windows®
XP / XP 64-bit.
ASRock 970 Extreme3 R2.0 Motherboard
9
1.3 Unique Features
ASRock Extreme Tuning Utility (AXTU)
ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to
ne-tune different system functions in a user-friendly interface,
which includes Hardware Monitor, Fan Control, Overclocking,
OC DNA, IES and XFast RAM. In Hardware Monitor, it shows
the major readings of your system. In Fan Control, it shows the
fan speed and temperature for you to adjust. In Overclocking,
you are allowed to overclock CPU frequency for optimal system
performance. In OC DNA, you can save your OC settings as
a profile and share it with your friends. Your friends then can
load the OC profile to their own system to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator
can reduce the number of output phases to improve efficiency
when the CPU cores are idle without sacrificing computing performance. In XFast RAM, it fully utilizes the memory space that
cannot be used under Windows® OS 32-bit CPU.
ASRock Instant Boot
ASRock Instant Boot allows you to turn on your PC in just a few
seconds, provides a much more efficient way to save energy,
time, money, and improves system running speed for your system. It leverages the S3 and S4 ACPI features which normally
enable the Sleep/Standby and Hibernation modes in Windows®
to shorten boot up time. By calling S3 and S4 at specific timing
during the shutdown and startup process, Instant Boot allows
you to enter your Windows® desktop in a few seconds.
English
ASRock Instant Flash
ASRock Instant Flash is a BIOS flash utility embedded in Flash
ROM. This convenient BIOS update tool allows you to update
system BIOS without entering operating systems first like MSDOS or Windows®. With this utility, you can press the <F6> key
during the POST or the <F2> key to enter into the BIOS setup
menu to access ASRock Instant Flash. Just launch this tool and
save the new BIOS file to your USB flash drive, floppy disk or
hard drive, then you can update your BIOS only in a few clicks
without preparing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or
hard drive must use FAT32/16/12 file system.
10
ASRock 970 Extreme3 R2.0 Motherboard
ASRock APP Charger
If you desire a faster, less restricted way of charging your
Apple devices, such as iPhone/iPad/iPod Touch, ASRock has
prepared a wonderful solution for you - ASRock APP Charger.
Simply install the APP Charger driver, it makes your iPhone
charge much quickly from your computer and up to 40% faster
than before. ASRock APP Charger allows you to quickly charge
many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1),
Suspend to RAM (S3), hibernation mode (S4) or power off (S5).
With APP Charger driver installed, you can easily enjoy the marvelous charging experience.
ASRock XFast USB
ASRock XFast USB can boost USB storage device performance. The performance may depend on the properties of the
device.
ASRock XFast LAN
ASRock XFast LAN provides a faster internet access, which includes the benefits listed below. LAN Application Prioritization:
You can configure your application’s priority ideally and/or add
new programs. Lower Latency in Game: After setting online
game’s priority higher, it can lower the latency in games. Traffic
Shaping: You can watch Youtube HD videos and download simultaneously. Real-Time Analysis of Your Data: With the status
window, you can easily recognize which data streams you are
transferring currently.
ASRock 970 Extreme3 R2.0 Motherboard
English
ASRock XFast RAM
ASRock XFast RAM is a new function that is included into ASRock Extreme Tuning Utility (AXTU). It fully utilizes the memory
space that cannot be used under Windows® OS 32-bit CPU.
ASRock XFast RAM shortens the loading time of previously
visited websites, making web surfing faster than ever. And it
also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the
frequency of accessing your SSDs or HDDs in order to extend
their lifespan.
11
ASRock Crashless BIOS
ASRock Crashless BIOS allows users to update their BIOS
without fear of failing. If power loss occurs during the BIOS update process, ASRock Crashless BIOS will automatically finish
the BIOS update procedure after regaining power. Please note
that BIOS files need to be placed in the root directory of your
USB disk. Only USB2.0 ports support this feature.
ASRock OMG (Online Management Guard)
Administrators are able to establish an internet curfew or restrict
internet access at specified times via OMG. You may schedule
the starting and ending hours of internet access granted to other
users. In order to prevent users from bypassing OMG, guest
accounts without permission to modify the system time are required.
ASRock Internet Flash
ASRock Internet Flash searches for available UEFI firmware
updates from our servers. In other words, the system can autodetect the latest UEFI from our servers and flash them without
entering Windows® OS. Please note that you must be running
on a DHCP configured computer in order to enable this function.
ASRock On/Off Play Technology
ASRock On/Off Play Technology allows users to enjoy the great
audio experience from the portable audio devices, such like
MP3 player or mobile phone to your PC, even when the PC is
turned off (or in ACPI S5 mode)! This motherboard also provides
a free 3.5mm audio cable (optional) that ensures users the most
convenient computing environment.
English
ASRock UEFI System Browser
ASRock UEFI system browser is a useful tool included in
graphical UEFI. It can detect the devices and configurations
that users are currently using in their PC. With the UEFI system
browser, you can easily examine the current system configuration in UEFI setup.
ASRock Dehumidifier Function
Users may prevent motherboard damages due to dampness by
enabling “Dehumidifier Function”. When enabling Dehumidifier
12
ASRock 970 Extreme3 R2.0 Motherboard
Function, the computer will power on automatically to dehumidify the system after entering S4/S5 state.
ASRock Fast Boot
With ASRock’s exclusive Fast Boot technology, it takes less
than 1.5 seconds to logon to Windows® 8 from a cold boot. No
more waiting! The speedy boot will completely change your user
experience and behavior.
ASRock X-Boost
ASRock’s X-Boost Technology is a smart auto-overclocking
function and is brilliantly designed to unlock the hidden power of
your CPUs. Simply press “X” when turning on the PC, X-Boost
will automatically overclock the relative components to get up to
15.77% performance boost! With the smart X-Boost, overclocking CPU can become a near one-button process.
* The functionality of “Unlock CPU Cores” feature might vary by different processors.
ASRock Restart to UEFI
Windows® 8 brings the ultimate boot up experience. The lightning boot up speed makes it hard to access the UEFI setup. ASRock Restart to UEFI technology is designed for those requiring
frequent UEFI access. It allows users to easily enter the UEFI
automatically when turning on the PC next time. Just simply
enable this function; the PC will be assured to access the UEFI
directly in the very beginning.
ASRock 970 Extreme3 R2.0 Motherboard
English
ASRock Good Night LED
ASRock Good Night LED technology can offer you a better environment by extinguishing the unessential LED. By enabling
Good Night LED in BIOS, the Power / HDD / LAN LED will be
switched off when system is on. Not only this, Good night LED
will automatically switch off Power and Keyboard LED when the
system enters into Standby / Hibernation mode as well.
13
2. Installation
This is an ATX form factor motherboard. Before you install the motherboard, study
the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. 2. 3. 4. 5.
Unplug the power cord from the wall socket before touching any
component.
To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the
like. Also remember to use a grounded wrist strap or touch a safety
grounded object before you handle components.
Hold components by the edges and do not touch the ICs.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing
so may damage the motherboard.
English
14
ASRock 970 Extreme3 R2.0 Motherboard
2.1 CPU Installation
o
Step 1. Unlock the socket by lifting the lever up to a 90 angle.
Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
Lever 90° Up
CPU Golden Triangle
Socker Corner
Small Triangle
STEP 1:
Lift Up The Socket Lever
STEP 2 / STEP 3:
STEP 4:
Match The CPU Golden Triangle Push Down And Lock
To The Socket Corner Small
The Socket Lever
Triangle
2.2 Installation of CPU Fan and Heatsink
English
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened
and in good contact with each other. Then connect the CPU fan to the
CPU FAN connector (CPU_FAN1, see Page 2, No. 6 or CPU_FAN2, see
Page 2, No. 5). For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.
ASRock 970 Extreme3 R2.0 Motherboard
15
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,
and supports Dual Channel Memory Technology. For dual channel configuration,
you always need to install identical (the same brand, speed, size and chip-type)
DDR3 DIMM pair in the slots. In other words, you have to install identical DDR3
DIMM pair in Dual Channel (DDR3_A1 and DDR3_B1; Black slots; see p.2 No.7)
or identical DDR3 DIMM pair in Dual Channel (DDR3_A2 and DDR3_B2; Black
slots; see p.2 No.8), so that Dual Channel Memory Technology can be activated.
This motherboard also allows you to install four DDR3 DIMMs for dual channel
configuration, and please install identical DDR3 DIMMs in all four slots. You may
refer to the Dual Channel Memory Configuration Table below.
Dual Channel Memory Configurations
(1)
(2)
(3)*
DDR3_A1
(Black Slot)
Populated
-
Populated
DDR3_A2
(Black Slot)
-
Populated
Populated
DDR3_B1
DDR3_B2
(Black Slot) (Black Slot)
Populated
Populated
Populated
Populated
* For the configuration (3), please install identical DDR3 DIMMs in all four slots.
English
1. Please install the memory module into the slots DDR3_A2 and
DDR3_B2 for the first priority.
2. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them either in the set of
slots DDR3_A1 and DDR3_B1, or in the set of slots DDR3_A2 and
DDR3_B2.
3. If only one memory module or three memory modules are installed
in the DDR3 DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
4. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in
DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel
Memory Technology .
5. It is not allowed to install a DDR or DDR2 memory module into
DDR3 slot; otherwise, this motherboard and DIMM may be damaged.
6. If you adopt DDR3 2100/1866/1800/1600 memory modules on this
motherboard, it is recommended to install them on DDR3_A2 and
DDR3_B2 slots.
16
ASRock 970 Extreme3 R2.0 Motherboard
Installing a DIMM
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.
English
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
ASRock 970 Extreme3 R2.0 Motherboard
17
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 2 PCI slots and 4 PCI Express slots on this motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.
PCIE Slots:
PCIE1 / PCIE3 (PCIE x1 slot) is used for PCI Express cards with x1
lane width cards, such as Gigabit LAN card and SATA2 card.
PCIE2 (PCIE x16 slot) is used for PCI Express x16 lane width graphics
cards, or used to install PCI Express graphics cards to support
CrossFireXTM function. PCIE4 (PCIE x16 slot) is used for PCI Express x4 lane width cards,
or used to install PCI Express graphics cards to support CrossFireXTM
function.
1. In single VGA card mode, it is recommended to install a PCI Express x16 graphics card on PCIE2 slot.
2. In CrossFireXTM mode, please install PCI Express x16 graphics
cards on PCIE2 and PCIE4 slots. Therefore, PCIE2 slot will work at
x16 bandwidth while PCIE4 slot will work at x4 bandwidth.
3. Please connect a chassis fan to motherboard chassis fan connector (CHA_FAN1, CHA_FAN2 or CHA_FAN3) when using multiple
graphics cards for better thermal environment.
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
English
Step 5.
Step 6. 18
Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed
in a chassis).
Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Align the card connector with the slot and press firmly until the card is completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
ASRock 970 Extreme3 R2.0 Motherboard
2.5 CrossFireXTM and Quad CrossFireXTM Operation Guide
This motherboard supports CrossFireX TM and Quad CrossFireX TM feature.
CrossFireX TM technology offers the most advantageous means available of
combining multiple high performance Graphics Processing Units (GPU) in a single
PC. Combining a range of different operating modes with intelligent software design
and an innovative interconnect mechanism, CrossFireXTM enables the highest
possible level of performance and image quality in any 3D application. Currently
CrossFireXTM feature is supported with Windows® XP with Service Pack 2 / VistaTM /
7 / 8 OS. Quad CrossFireXTM feature is supported with Windows® VistaTM / 7 / 8 OS
only. Please check AMD website for AMD CrossFireXTM driver updates.
1. If a customer incorrectly configures their system they will not see the
performance benefits of CrossFireXTM. All three CrossFireXTM components, a
CrossFireXTM Ready graphics card, a CrossFireXTM Ready motherboard and a
CrossFireXTM Edition co-processor graphics card, must be installed correctly
to benefit from the CrossFireXTM multi-GPU platform.
2. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both
cards will operate as 12-pipe cards while in CrossFireXTM mode.
2.5.1 Graphics Card Setup
2.5.1.1 Installing Two CrossFireXTM-Ready Graphics Cards
Different CrossFireXTM cards may require different methods to enable CrossFireXTM feature. For other CrossFireXTM cards that AMD has released or will release
in the future, please refer to AMD graphics card manuals for detailed installation
guide.
English
Step 1. Insert one Radeon graphics card into PCIE2 slot and the other Radeon
graphics card to PCIE4 slot. Make sure that the cards are properly seated
on the slots.
ASRock 970 Extreme3 R2.0 Motherboard
19
Step 2. Connect two Radeon graphics cards by installing a CrossFire Bridge on
the CrossFire Bridge Interconnects on the top of the Radeon graphics
cards. (The CrossFire Bridge is provided with the graphics card you purchase, not bundled with this motherboard. Please refer to your graphics
card vendor for details.)
CrossFire Bridge
or
Step 3. Connect the DVI monitor cable to the DVI connector on the Radeon graphics card on PCIE2 slot. (You may use the DVI to D-Sub adapter to convert
the DVI connector to D-Sub interface, and then connect the D-Sub monitor
cable to the DVI to D-Sub adapter.)
English
20
ASRock 970 Extreme3 R2.0 Motherboard
2.5.2 Driver Installation and Setup
Step 1. Power on your computer and boot into OS.
Step 2. Remove the AMD driver if you have any VGA driver installed in your system.
The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation.
Please check AMD website for AMD driver updates.
Step 3. Install the required drivers to your system.
For Windows® XP OS:
A. AMD recommends Windows® XP Service Pack 2 or higher to be installed (If you have Windows® XP Service Pack 2 or higher installed in your system, there is no need to download it again):
http://www.microsoft.com/windowsxp/sp2/default.mspx
B. You must have Microsoft .NET Framework installed prior to downloading and installing the CATALYST Control Center. Please check Microsoft website for details.
For Windows® 8 / 7 / VistaTM OS:
Install the CATALYST Control Center. Please check AMD website for details.
Step 4. Restart your computer.
Step 5. Install the VGA card drivers to your system, and restart your computer.
Then you will find “ATI Catalyst Control Center” on your Windows® taskbar.
ATI Catalyst Control Center
English
Step 6. Double-click “ATI Catalyst Control Center”. Click “View”, select “CrossFireXTM”, and then check the item “Enable CrossFireXTM”. Select “2 GPUs”
and click “Apply” (if you install two Radeon graphics cards).
ASRock 970 Extreme3 R2.0 Motherboard
21
Although you have selected the option “Enable CrossFireTM”, the CrossFireXTM function may not work actually. Your computer will automatically
reboot. After restarting your computer, please confirm whether the option
“Enable CrossFireTM” in “ATI Catalyst Control Center” is selected or not;
if not, please select it again, and then you are able to enjoy the benefit of
CrossFireXTM feature.
Step 7. You can freely enjoy the benefit of CrossFireXTM or Quad CrossFireXTM
feature.
* CrossFireXTM appearing here is a registered trademark of AMD Technologies Inc., and is used only for identification or explanation and to the owners’ benefit, without intent to infringe.
* For further information of AMD CrossFireXTM technology, please check AMD website for updates and details.
English
22
ASRock 970 Extreme3 R2.0 Motherboard
2.6 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.
Jumper
Setting
Clear CMOS Jumper
Description
(CLRCMOS1)
(see p.2, No. 21)
Default
Clear CMOS
English
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need
to clear the CMOS when you just finish updating the BIOS, you must boot
up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394
GUID and MAC address will be cleared only if the CMOS battery is removed.
ASRock 970 Extreme3 R2.0 Motherboard
23
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
Serial ATA3 Connectors
(SATA3_1: see p.2, No. 17) (SATA3_2: see p.2, No. 18)
(SATA3_3: see p.2, No. 16)
(SATA3_4: see p.2, No. 19) SATA3_5
(SATA3_5: see p.2, No. 20)
SATA3_3
SATA3_1
SATA3_4
SATA3_2
These five Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to
6.0 Gb/s data transfer rate.
Serial ATA (SATA)
Data Cable
(Optional)
Either end of the SATA data cable can be connected to the SATA / SATA2 / SATA3 hard disk or the SATA3 connector on
this motherboard.
USB 2.0 Headers
(9-pin USB_4_5)
(see p.2 No. 26)
Besides four default USB 2.0
ports on the I/O panel, there
are three USB 2.0 headers on
this motherboard. Each USB 2.0
header can support two USB
2.0 ports.
(9-pin USB_6_7)
(see p.2 No. 27)
USB_PWR
P-9
P+9
GND
DUMMY
(9-pin USB_8_9)
(see p.2 No. 28)
1
English
GND
P+8
P-8
USB_PWR
Infrared Module Header
(5-pin IR1)
(see p.2 No. 29)
24
This header supports an
optional wireless transmitting
and receiving infrared module.
ASRock 970 Extreme3 R2.0 Motherboard
Consumer Infrared Module Header
(4-pin CIR1)
(see p.2 No. 25)
This header can be used to connect the remote controller receiver.
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.2 No. 32)
This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.
GND
PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.
E. To activate the front mic.
For Windows® XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Go to the “FrontMic” Tab in the Realtek Control panel. Adjust “Recording Volume”.
System Panel Header
(9-pin PANEL1)
(see p.2 No. 23)
This header accommodates
several system front panel functions.
Connect the power switch, reset switch and system status indicator
on the chassis to this header according to the pin assignments below.
English
Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a normal restart.
ASRock 970 Extreme3 R2.0 Motherboard
25
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The
LED is on when the system is operating. The LED keeps blinking
when the sys-tem is in S1 sleep state. The LED is off when the system
is in S3/S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module
mainly consists of power switch, reset switch, power LED, hard drive
activity LED, speaker and etc. When connecting your chassis front
panel module to this header, make sure the wire assignments and the
pin assign-ments are matched correctly.
Chassis Speaker Header
(4-pin SPEAKER 1)
Please connect the chassis speaker to this header.
(see p.2 No. 24)
Power LED Header
(3-pin PLED1)
(see p.2 No. 22)
Please connect the chassis
power LED to this header to
indicate system power status. The LED is on when the system is operating. The LED keeps
blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).
Chassis and Power Fan Connectors
(4-pin CHA_FAN1)
(see p.2 No. 12)
Please connect the fan cables to the fan connectors and match the black wire to the ground pin. CHA_FAN1/2/3 fan
speed can be controlled through
UEFI or AXTU.
(3-pin CHA_FAN2)
(see p.2 No. 15)
GND
+12V
CHA_FAN_SPEED
English
(3-pin CHA_FAN3)
(see p.2 No. 2)
(3-pin PWR_FAN1)
(see p.2 No. 10)
26
ASRock 970 Extreme3 R2.0 Motherboard
CPU Fan Connectors FAN_SPEED_CONTROL
CPU_FAN_SPEED
(4-pin CPU_FAN1)
+12V
(see p.2 No. 6)
GND
Please connect the CPU fan
cable to the connector and
match the black wire to the ground pin.
1 2 3 4
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
(3-pin CPU_FAN2)
(see p.2 No. 5)
ATX Power Connector
(24-pin ATXPWR1)
GND
+12V
CPU_FAN_SPEED
12
24
1
13
Please connect an ATX power
supply to this connector.
(see p.2 No. 9)
Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
20-Pin ATX Power Supply Installation
ATX 12V Power Connector
(8-pin ATX12V1)
5
1
(see p.2 No. 1)
8
4
12
24
1
13
Please connect an ATX 12V power supply to this connector.
Though this motherboard provides 8-pin ATX 12V power connector, it can still work
5
1
if you adopt a traditional 4-pin ATX 12V power supply. To use the
4-pin ATX power supply, please plug your power supply along with
Pin 1 and Pin 5.
Serial port Header
(9-pin COM1)
8
4
English
4-Pin ATX 12V Power Supply Installation
This COM1 header supports a
serial port module.
(see p.2 No.30)
ASRock 970 Extreme3 R2.0 Motherboard
27
HDMI_SPDIF Header
(2-pin HDMI_SPDIF1)
HDMI_SPDIF header, providing SPDIF audio output to HDMI
(see p.2 No. 31)
VGA card, allows the system to
connect HDMI Digital TV/
projector/LCD devices. Please connect the HDMI_SPDIF
connector of HDMI VGA card to this header.
USB 3.0 Header
(19-pin USB3_2_3)
(see p.2 No. 38)
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P2_SSTXIntA_P2_SSTX+
GND
IntA_P3_SSTXIntA_P3_SSTX+
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
Besides two default USB 3.0
ports on the I/O panel, there is
one USB 3.0 header on this
motherboard. This USB 3.0
header can support two USB 3.0
ports.
2.8 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical
drive first. Then, the drivers compatible to your system can be auto-detected and
listed on the support CD driver page. Please follow the order from up to bottom side
to install those required drivers. Therefore, the drivers you install can work properly.
2.9 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit / XP / XP 64-bit With RAID Functions
If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP
/ XP 64-bit on your SATA3 HDDs with RAID functions, please refer to the document
at the following path in the Support CD for detailed procedures:
..\ RAID Installation Guide
English
2.10 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit / XP / XP 64-bit Without RAID Functions
If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP
/ XP 64-bit OS on your SATA3 HDDs without RAID functions, please follow below
procedures according to the OS you install.
28
ASRock 970 Extreme3 R2.0 Motherboard
2.10.1 Installing Windows® XP / XP 64-bit Without RAID
Functions
If you want to install Windows® XP / XP 64-bit on your SATA3 HDDs without RAID
functions, please follow below steps.
Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode)
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY
Advanced screen
Storage Configuration.
B. Set the “SATA Mode” option to [IDE].
STEP 2: Install Windows® XP / XP 64-bit OS on your system.
2.10.2 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit Without RAID Functions
If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on
your SATA3 HDDs without RAID functions, please follow below steps.
Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode)
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY
Advanced screen
Storage Configuration.
B. Set the “SATA Mode” option to [IDE].
STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on
your system.
Using SATA3 HDDs with NCQ and Hot Plug functions (AHCI mode)
ASRock 970 Extreme3 R2.0 Motherboard
English
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY
Advanced screen
Storage Configuration.
B. Set the “SATA Mode” option to [AHCI].
STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on
your system.
29
3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)
to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you
wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>
+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS
Setup program is designed to be user-friendly. It is a menu-driven program, which
allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the
User Manual (PDF file) contained in the Support CD.
4. Software Support CD information
This motherboard supports various Microsoft® Windows® operating systems: 8 / 8
64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. The Support CD that
came with the motherboard contains necessary drivers and useful utilities that will
enhance motherboard features. To begin using the Support CD, insert the CD into
your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is
enabled in your computer. If the Main Menu does not appear automatically, locate
and double-click on the file “ASSETUP.EXE” from the BIN folder in the Support CD
to display the menus.
English
30
ASRock 970 Extreme3 R2.0 Motherboard
1. Einführung
Wir danken Ihnen für den Kauf des ASRock 970 Extreme3 R2.0 Motherboard, ein
zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen
von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation
ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der
Support-CD.
Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet.
ASRock-Website: http://www.asrock.com
Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:
www.asrock.com/support/index.asp
1.1 Kartoninhalt
ASRock 970 Extreme3 R2.0 Motherboard (ATX-Formfaktor)
ASRock 970 Extreme3 R2.0 Schnellinstallationsanleitung
ASRock 970 Extreme3 R2.0 Support-CD
Zwei Serial ATA (SATA) -Datenkabel (optional)
Ein I/O Shield
ASRock erinnert...
Deutsch
Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / VistaTM
/ VistaTM 64 Bit empfehlen wir, die Speicherkonfiguration im BIOS auf den
AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen finden
Sie in der Bedienungsanleitung auf der mitgelieferten CD.
ASRock 970 Extreme3 R2.0 Motherboard
31
1.2 Spezifikationen
Plattform
CPU
Chipsatz
Speicher
Deutsch
Erweiterungs-
Steckplätze
Audio
LAN
32
- ATX-Formfaktor
- Alle Feste Kondensatordesign (100% in Japan gefertigte, erstklassige leitfähige Polymer-Kondensatoren)
- Unterstützung von Socket AM3+-Prozessoren
- Unterstützung von Socket AM3-Prozessoren: AMD
PhenomTM II X6 / X4 / X3 / X2 (außer 920 / 940) / Athlon X4 /
X3 / X2 / Sempron-Prozessor
- Acht-Kern-CPU-bereit
- Unterstützt UCC (Unlock CPU Core)
- Digi Power-Design
- 4 + 1-Stromphasendesign
- Unterstützt CPU bis 140W
- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD
- FSB 2400 MHz (4.8 GT/s)
- Unterstützt Untied-Übertaktungstechnologie
- Unterstützt Hyper-Transport- 3.0 Technologie (HT 3.0)
- Northbridge: AMD 970
- Southbridge: AMD SB950
- Unterstützung von Dual-Kanal-Speichertechnologie
- 4 x Steckplätze für DDR3
- Unterstützt DDR3 2100+(OC)1866(OC)/1800(OC)/1600
(OC)/1333/1066/800 non-ECC, ungepufferter Speicher
- Max. Kapazität des Systemspeichers: 32GB
- 2 x PCI-Express-2.0-x16-Steckplätze
(PCIE2: x16-Modus; PCIE4: x4-Modus) - 2 x PCI Express 2.0 x1-Steckplätze
- 2 x PCI -Steckplätze
- Unterstützt AMDTM Quad CrossFireXTM und CrossFireXTM
- 7.1 CH HD Audio mit dem Inhalt Schutz
(Realtek ALC892 Audio Codec)
- Premium Blu-ray-Audio-Unterstützung
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Unterstützt Wake-On-LAN
- Unterstützt LAN-Kabelerkennung
- Unterstützt energieeffizientes Ethernet 802.3az
- Unterstützt PXE
ASRock 970 Extreme3 R2.0 Motherboard
I/O Panel
- 1 x PS/2-Mausanschluss
- 1 x PS/2-Tastaturanschluss
- 1 x Koaxial-SPDIF-Ausgang
- 1 x optischer SPDIF-Ausgang
- 4 x Standard-USB 2.0-Anschlüsse
- 2 x Standard-USB 3.0-Anschlüsse
- 1 x eSATA3-Anschluss
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED
LED)
- HD Audiobuchse: Lautsprecher seitlich / Lautsprecher
hinten / Mitte/Bass / Audioeingang/ Lautsprecher vorne /
Mikrofon
- 5 x SATA 3-Anschluss mit 6,0 Gb/s, unterstützt RAID(RAID 0, RAID 1, RAID 5 und RAID 10), NCQ-, AHCI- und
„Hot Plugging“-Funktionen
- 2 x USB 3.0-Ports an der Rückseite durch Etron EJ188H,
unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s
- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der
Vorderseite durch Etron EJ188H, unterstützt USB 1.1/2.0/3.0
mit bis zu 5 Gb/s
- 5 x SATA3 6,0 GB/s-Anschlüsse
- 1 x Infrarot-Modul-Header
- 1 x Consumer Infrarot-Modul-Header
- 1 x COM-Anschluss-Header
- 1 x HDMI_SPDIF-Anschluss
- 1 x Betriebs-LED-Header
- 2 x CPUlüfter-Anschluss (1 x 4-pin, 1 x 3-pin)
- 3 x Gehäuselüfter-Anschluss (1 x 4-pin, 2 x 3-pin)
- 1 x Stromlüfter-Anschluss (3-pin)
- 24-pin ATX-Netz-Header
- 8-pin anschluss für 12V-ATX-Netzteil
- Anschluss für Audio auf der Gehäusevorderseite
- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
USB 2.0-Anschlüsse)
- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher
USB 3.0-Anschlüsse)
- 32Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung
- Unterstützung für “Plug and Play”
- ACPI 1.1-Weckfunktionen
- JumperFree-Modus
ASRock 970 Extreme3 R2.0 Motherboard
Deutsch
E/A-Anschlüsse an der Rückseite
SATA3
USB3.0
Anschlüsse
BIOS 33
Support-CD
Hardware Monitor
Betriebssysteme
Zertifizierungen
- SMBIOS 2.3.1
- CPU, VCCM, NB, SB Stromspannung Multianpassung
- Treiber, Dienstprogramme, Antivirussoftware (Probeversion), CyberLink MediaEspresso 6.5-Testversion,
Google Chrome Browser und Toolbar
- CPU-Temperatursensor
- Motherboardtemperaturerkennung
- Drehzahlmessung für CPU/Gehäuse/Stromlüfter
- CPU-/Gehäuselüftergeräuschdämpfung
- Mehrstufige Geschwindigkeitsteuerung für CPU-/
Gehäuselüfter
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
- Unterstützt Microsoft® Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /
VistaTM / VistaTM 64-Bit / XP / XP 64-Bit
- FCC, CE, WHQL
- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung
gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com
Deutsch
34
ASRock 970 Extreme3 R2.0 Motherboard
1.3 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper
g e s e t z t w e r d e n . We r d e n P i n s d u r c h
Jumperkappen verdeckt, ist der Jumper
“gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “offen”.
Die Abbildung zeigt einen 3-Pin Jumper
dessen Pin1 und Pin2 “gebrückt” sind, bzw.
es befindet sich eine Jumper-Kappe auf
diesen beiden Pins.
Jumper
CMOS löschen
(CLRCMOS1, 3-Pin jumper)
(siehe S.2, No. 21)
Einstellun
DefaultEinstellung
CMOS
löschen
Deutsch
Hinweis: CLRCMOS1 erlaubt Ihnen das Löschen der CMOS-Daten. Diese beinhalten das System-Passwort, Datum, Zeit und die verschiedenen BIOS-Parameter. Um die Systemparameter zu löschen und auf die Werkseinstellung
zurückzusetzen, schalten Sie bitte den Computer ab und entfernen das
Stromkabel. Benutzen Sie eine Jumperkappe, um die
Pin 2 und Pin 3 an CLRCMOS1 für 5 Sekunden kurzzuschließen. Bitte vergessen Sie nicht, den Jumper wieder zu entfernen, nachdem das
CMOS gelöscht wurde. Bitte vergessen Sie nicht, den Jumper wieder zu
entfernen, nachdem das CMOS gelöscht wurde. Wenn Sie den CMOSInhalt gleich nach dem Aktualisieren des BIOS löschen müssen, müssen
Sie zuerst das System starten und dann wieder ausschalten, bevor Sie
den CMOS-Inhalt löschen.
ASRock 970 Extreme3 R2.0 Motherboard
35
1.4 Anschlüsse
Anschlussleisten sind KEINE Jumper. Setzen Sie KEINE Jumperkappen
auf die Pins der Anschlussleisten. Wenn Sie die Jumperkappen auf die Anschlüsse setzen, wird das Motherboard permanent beschädigt!
Anschluss
Seriell-ATA3-Anschlüsse
(SATA3_1: siehe S.2 - No. 17) (SATA3_2: siehe S.2 - No. 18) (SATA3_3: siehe S.2 - No. 16) (SATA3_4: siehe S.2 - No. 19) SATA3_5
(SATA3_5: siehe S.2 - No. 20) Beschreibung
SATA3_3
SATA3_1
SATA3_4
SATA3_2
Diese fünf Serial ATA3- (SATA3-)Verbínder unterstützten SATA-Datenkabel für interne Massenspeichergeräte. Die aktuelle SATA3- Schnittstelle ermöglicht eine Datenübertragungsrate bis
6,0 Gb/s.
Serial ATA- (SATA-) Datenkabel
(Option)
SJedes Ende des SATA Datenkabels kann an die
SATA / SATAII / SATA3
Festplatte oder das SATA3
Verbindungsstück auf dieser
Hauptplatine angeschlossen
werden.
USB 2.0-Header
(9-pol. USB_4_5)
(siehe S.2 - No. 26) (9-pol. USB_6_7)
(siehe S.2 - No. 27) Zusätzlich zu den vier üblichen USB 2.0-Ports an den
I/O-Anschlüssen befinden sich drei USB 2.0-
Anschlussleisten am Motherboard. Pro USB 2.0-
Anschlussleiste werden zwei USB 2.0-Ports unterstützt.
Deutsch
(9-pol. USB_8_9)
(siehe S.2 - No. 28)
USB_PWR
P-9
P+9
GND
DUMMY
1
GND
P+8
P-8
USB_PWR
36
ASRock 970 Extreme3 R2.0 Motherboard
Infrarot-Modul-Header
(5-pin IR1)
Dieser Header unterstützt ein optionales, drahtloses Sende- (siehe S.2 - No. 29) und Empfangs-Infrarotmodul.
Consumer Infrared-Modul-Header
(4-pin CIR1)
(siehe S.2 - No. 25)
Dieser Header kann zum Anschließen RemoteEmpfänger.
Anschluss für Audio auf der Gehäusevorderseite
(9-Pin HD_AUDIO1)
(siehe S.2 - No. 32)
Dieses Interface zu einem
Audio-Panel auf der Vorder
seite Ihres Gehäuses,
ermöglicht Ihnen eine bequeme Anschlussmöglichkeit und Kontrolle über Audio-Geräte.
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste:
A. Schließen Sie Mic_IN (MIC) an MIC2_L an.
B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) anOUT2_L an.
1
C. Schließen Sie Ground (GND) an Ground (GND) an.
D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.
E. So aktivieren Sie das Mikrofon an der Vorderseite.
Bei den Betriebssystemen Windows® XP / XP 64 Bit:
Wählen Sie „Mixer“. Wählen Sie „Recorder“ (Rekorder). Klicken Sie dann auf „FrontMic“ (Vorderes Mikrofon).
Bei den Betriebssystemen Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / VistaTM / VistaTM
64 Bit:
Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)-
Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke) an.
System Panel-Header
(9-pin PANEL1)
(siehe S.2 - No. 23)
Deutsch
GND
PRESENCE#
MIC_RET
OUT_RET
Dieser Header unterstützt mehrere Funktion der Systemvorderseite.
ASRock 970 Extreme3 R2.0 Motherboard
37
Schließen Sie die Ein-/Austaste, die Reset-Taste und die
Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die positiven und negativen Pins, bevor Sie die Kabel anschließen.
PWRBTN (Ein-/Ausschalter):
Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu
ses. Sie können konfigurieren, wie das System mit Hilfe des
Ein-/Ausschalters ausgeschaltet werden können soll.
RESET (Reset-Taste):
Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses. Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes neu starten.
PLED (Systembetriebs-LED):
Zum Anschließen der Betriebsstatusanzeige an der Frontblende des
Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt, wenn sich das System im Ruhezustand S1 befindet. Die LED
schaltet sich aus, wenn sich das System in den Modi S3/S4 befindet oder ausgeschaltet ist (S5).
HDLED (Festplattenaktivitäts-LED):
Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des
Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variiere. Ein Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED, Lautsprechern, etc. Stellen Sie beim Anschließen des
Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die
Kabel- und Pinbelegung korrekt übereinstimmen.
Gehäuselautsprecher-Header
(4-pin SPEAKER1)
(siehe S.2 - No. 24)
Schließen Sie den Gehäuselautsprecher an
diesen Header an.
Betriebs-LED-Header
(3-pin PLED1)
Bitte schließen Sie die
Betriebs-LED des Gehäuses
Deutsch
(siehe S.2 - No. 22)
38
zur Anzeige des
Systembetriebsstatus an
diesem Header an. Die LED
leuchtet, wenn das System in
Betrieb ist. Die LED blinkt im S1-Zustand. Im S3-/S4- oder S5-Zustand (ausgeschaltet)
leuchtet die LED nicht.
ASRock 970 Extreme3 R2.0 Motherboard
Gehäuse- und Stromlüfteranschlüsse
(4-pin CHA_FAN1)
Verbinden Sie die Lüfterkabel mit den Lüfteranschlüssen, (siehe S.2, No. 12)
wobei der schwarze Draht an den Schutzleiterstift angeschlossenwird. CHA_
FAN1/2/3-Lüftergeschwindigkeit
kann über UEFI oder AXTU
gesteuert werden.
(3-pin CHA_FAN2)
GND
+12V
CHA_FAN_SPEED
(siehe S.2 - No. 15)
(3-pin CHA_FAN3)
(siehe S.2 - No. 2)
(3-pin PWR_FAN1)
(siehe S.2 - No. 10)
CPU-Lüfteranschluss
(4-pin CPU_FAN1)
(siehe S.2 - No. 6)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Verbinden Sie das CPU -
Lüfterkabel mit diesem Anschluss und passen Sie den schwarzen Draht dem Erdungsstift an.
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss
(Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den
Pins 1 – 3.
Pins 1–3 anschließen
Lüfter mit dreipoligem Anschluss installieren
(siehe S.2 - No. 5)
ATX-Netz-Header
(24-pin ATXPWR1)
(siehe S.2 - No. 9)
GND
+12V
CPU_FAN_SPEED
12
24
1
13
Verbinden Sie die ATX-
Stromversorgung mit diesem Header.
ASRock 970 Extreme3 R2.0 Motherboard
Deutsch
(3-pin CPU_FAN2)
39
Obwohl dieses Motherboard einen 24-pol. ATXStromanschluss bietet, kann es auch mit einem
modifizierten traditionellen 20-pol. ATX-Netzteil
verwendet werden. Um ein 20-pol. ATX-Netzteil zu
verwenden, stecken Sie den Stecker mit Pin 1 und
Pin 13 ein.
Installation eines 20-pol. ATX-Netzteils
ATX 12V Anschluss
(8-pin ATX12V1)
(siehe S.2 - No. 1)
5
1
8
4
24
1
13
Bitte schließen Sie an diesen Anschluss die ATX 12V Stromversorgung an.
Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur
Verfügung stellt, kann sie noch arbeiten, wenn Sie einen
traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die 4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre
Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.
Installation der 4-Pin ATX 12V Energieversorgung
COM-Anschluss-Header
(9-pin COM1)
5
1
8
4
Dieser COM-Anschluss-
Header wird verwendet, um ein COM-Anschlussmodul zu unterstützen.
HDMI_SPDIF-Anschluss
(2-pin HDMI_SPDIF1)
(siehe S.2 - No. 31)
Der HDMI_SPDIF-Anschluss stellt einen SPDIF
Audioausgang für eine HDMI-
VGA-Karte zur Verfügung und ermöglicht den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten, Projektoren, LCD-Geräten an das System.
Bitte verbinden Sie den
HDMI_SPDIF-Anschluss der HDMI-VGA-Karte mit diesem Anschluss.
(siehe S.2 - No. 30)
Deutsch
40
12
ASRock 970 Extreme3 R2.0 Motherboard
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
Neben zwei Standard-USB
3.0-Ports am E/A-Panel
befindet sich ein USB 3.0Header an diesem
Motherboard. Dieser USB 3.0Header kann zwei USB 3.0Ports unterstützen.
Deutsch
USB 3.0-Header
(19-pol. USB3_2_3)
(siehe S.2 - No. 38)
ASRock 970 Extreme3 R2.0 Motherboard
41
2. BIOS-Information
Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie
<F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelangen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup
gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System
über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf
der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch
durchführen, indem Sie das System kurz ab- und danach wieder anschalten.
Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein
menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der
Support CD.
3. Software Support CD information
Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebssystemen: 8 / 8 64-Bit / 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit / XP / XP 64-Bit. Die
Ihrem Motherboard beigefügte Support-CD enthält hilfreiche Software, Treiber und
Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen,
wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben.
Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File
ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen.
Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menügesteuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und
die Programme werden dann automatisch installiert.
Deutsch
42
ASRock 970 Extreme3 R2.0 Motherboard
1. Introduction
Merci pour votre achat d’une carte mère ASRock 970 Extreme3 R2.0, une carte
mère très fiable produite selon les critères de qualité rigoureux de ASRock. Elle
offre des performances excellentes et une conception robuste conformément à
l’engagement d’ASRock sur la qualité et la fiabilité au long terme.
Ce Guide d’installation rapide présente la carte mère et constitue un guide
d’installation pas à pas. Des informations plus détaillées concernant la carte
mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD
d’assistance.
Les spécifications de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notification. Au cas où n’importe qu’elle modification intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis. Vous trouverez les listes de prise en charge des cartes VGA et CPU également sur le site Web ASRock.
Site web ASRock, http://www.asrock.com
Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez.
www.asrock.com/support/index.asp
1.1 Contenu du paquet
Carte mère ASRock 970 Extreme3 R2.0 (Facteur de forme ATX)
Guide d’installation rapide ASRock 970 Extreme3 R2.0
CD de soutien ASRock 970 Extreme3 R2.0
Deux câbles de données de série ATA (SATA) (en option)
Un I/O Panel Shield
ASRock vous rappelle...
ASRock 970 Extreme3 R2.0 Motherboard
Français
Pour bénéficier des meilleures performances sous Windows® 8 / 8 64 bits
/ 7 / 7 64 bits / VistaTM / VistaTM 64 bits, il est recommandé de paramétrer
l'option BIOS dans Configuration de stockage en mode AHCI. Pour plus
de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur
votre CD de support.
43
1.2 Spécifications
Format
CPU
Chipsets
Mémoire
Français
Slot d’extension
Audio
LAN
44
- Facteur de forme ATX
- Accessoires de Carte mère (condensateurs 100% polymère conducteur de haute qualité fabriqué au Japon)
- Prise en charge des processeurs sur socket AM3+
- Prise en charge des processeurs sur socket AM3:
Processeur PhenomTM II X6 / X4 / X3 / X2 (sauf 920 / 940) /
Athlon II X4 / X3 / X2 / Sempron d’AMD
- Prêt pour processeurs Huit-Core
- Supporte UCC (Unlock CPU Core)
- Conception Digi Power
- Conception 4 + 1 Power Phase
- Supporte les processeurs jusqu’à 140W
- Supporte la technologie Cool ‘n’ QuietTM d’AMD
- FSB 2400 MHz (4.8 GT/s)
- Prend en charge la technologie Untied Overclocking
- Prise en charge de la technologie Hyper Transport 3.0
(HT 3.0)
- Northbridge: AMD 970
- Southbridge: AMD SB950
- Compatible avec la Technologie de Mémoire à Canal
Double
- 4 x slots DIMM DDR3
- Supporter DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)
/1333/1066/800 non-ECC, sans amortissement mémoire
- Capacité maxi de mémoire système: 32GB
- 2 x slots PCI Express 2.0 x16
(PCIE2: mode x16; PCIE4: mode x4)
- 2 x slot PCI Express 2.0 x1
- 2 x slots PCI
- Prend en charge AMDTM Quad CrossFireXTM et CrossFireXTM
- 7,1 CH HD Audio avec protection de contenu
(Realtek ALC892 Audio Codec)
- Prise en charge de l’audio Premium Blu-ray
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supporte du Wake-On-LAN
- Prise en charge de la détection de câble LAN
- Prend en charge la norme Energy Efficient Ethernet
ASRock 970 Extreme3 R2.0 Motherboard
(Ethernet à efficacité énergétique) 802.3az
- Support de PXE
Panneau arrière I/O Panel
- 1 x port souris PS/2
- 1 x port clavier PS/2
- 1 x Port de sortie coaxial SPDIF
- 1 x Port de sortie optique SPDIF
- 4 x ports USB 2.0 par défaut
- 2 x ports USB 3.0 par défaut
- 1 x Connecteur eSATA3
- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et LED VITESSE)
- Prise HD Audio: Haut-parleur latéral / Haut-parleur arrière /
Central /Basses / Entrée Ligne / Haut-parleur frontal /
Microphone
- 5 x connecteurs 6,0 Gb/s SATA3, prise en charge des
fonctions RAID (RAID 0, RAID 1, RAID 5 et RAID 10), NCQ,
AHCI et « Connexion à chaud »
- 2 x ports USB3.0 à l’arrière par Etron EJ188H, prennent en
charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s
- 1 x barrette USB3.0 en façade (prend en charge 2 ports
USB 3.0) par Etron EJ188H, prend en charge USB
1.1/2.0/3.0 jusqu’à 5 Gb/s
- 5 x connecteurs SATA3, prennent en charge un taux de transfert de données pouvant aller jusqu’à 6.0Go/s
- 1 x En-tête du module infrarouge
- 1 x Barrette pour module à infrarouges grand public
- 1 x En-tête de port COM
- 1 x Connecteur HDMI_SPDIF
- 1 x LED di accensione
- 2 x Connecteur pour ventilateur de CPU (1 x br. 4, 1 x br. 3)
- 3 x Connecteur pour ventilateur de Châssis
(1 x br. 4, 2 x br. 3)
- 1 x Connecteur pour ventilateur de pouvoir (br. 3)
- br. 24 connecteur d’alimentation ATX
- br. 8 connecteur d’alimentation 12V ATX
- Connecteur audio panneau avant
- 3 x En-tête USB 2.0 (prendre en charge 6 ports USB 2.0 supplémentaires)
- 1 x En-tête USB 3.0 (prendre en charge 2 ports USB 3.0
supplémentaires)
SATA3
USB 3.0
Connecteurs
ASRock 970 Extreme3 R2.0 Motherboard
Français
45
BIOS CD d’assistance
Surveillance système
OS
Certifications
- 32Mb AMI UEFI Legal BIOS avec support GUI
- Support du “Plug and Play”
- Compatible pour événements de réveil ACPI 1.1
- Gestion jumperless
- Support SMBIOS 2.3.1 - CPU, VCCM, NB, SB Tension Multi-ajustement
- Pilotes, utilitaires, logiciel anti-virus (Version d’essai),
CyberLink MediaEspresso 6.5 Trial, Google Chrome
Browser et Toolbar
- Détection de la température de l’UC
- Mesure de température de la carte mère
- Tachéomètre ventilateur CPU/Châssis/Ventilateur
- Ventilateur silencieux pour unité centrale/châssis
- Commande de ventilateur CPU/boîtier à plusieurs vitesses
- Monitoring de la tension: +12V, +5V, +3.3V, Vcore
- Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit / XP / XP 64-bit
- FCC, CE, WHQL
- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web:
http://www.asrock.com
Français
46
ASRock 970 Extreme3 R2.0 Motherboard
1.3 Réglage des cavaliers
L’illustration explique le réglage des cavaliers. Quand un capuchon est placé sur les
broches, le cavalier est « FERME ». Si aucun capuchon ne relie les broches,le cavalier est « OUVERT ». L’illustration montre un
cavalier à 3 broches dont les broches 1 et 2
sont « FERMEES » quand le capuchon est
placé sur ces 2 broches.
Le cavalier
Effacer la CMOS
(CLRCMOS1)
(voir p.2 fig. 21)
Paramètres
par défaut
Description
Effacer la
CMOS
Français
Remarque :CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer
et réinitialiser les paramètres du système à la configuration originale,
veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de
la prise de courant. Après 15 secondes, utilisez un couvercle de jumper
pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant 5
secondes. Veuillez cependant ne pas effacer le CMOS immédiatement
après avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS
après avoir mis à jour le BIOS, vous devez allumer en premier le
système, puis l’éteindre avant de continuer avec l’opération d’effacement
du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le profil
par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés
seulement si la batterie du CMOS est enlevée.
ASRock 970 Extreme3 R2.0 Motherboard
47
1.4 En-têtes et Connecteurs sur Carte
Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers.
NE PAS placer les capuchons de cavalier sur ces en-têtes et connecteurs. Le fait de placer les capuchons de cavalier sur les en-têtes
et connecteurs causera à la carte mère des dommages irréversibles!
Connecteurs Série ATA3
(SATA3_1: voir p.2 No. 17) (SATA3_2: voir p.2 No. 18)
(SATA3_3 voir p.2 No. 16)
(SATA3_4 voir p.2 No. 19) SATA3_5
(SATA3_5 voir p.2 No. 20)
SATA3_3
SATA3_1
SATA3_4
SATA3_2
Ces cinq connecteurs Série ATA3 (SATA3) prennent en charge les câbles SATA pour les périphériques de stockage internes. L’interface SATA3
actuelle permet des taux transferts de données pouvant aller jusqu’à 6,0 Gb/s.
Câble de données Série ATA (SATA)
(en option)
Toute cote du cable de data
SATA peut etre connecte au disque dur SATA / SATAII /
SATA3 ou au connecteur SATA3
sur la carte mere.
En-tête USB 2.0
(USB_4_5 br.9)
(voir p.2 No. 26)
(USB_6_7 br.9)
A côté des quatre ports USB
2.0 par défaut sur le panneau E/S, il y a troi embases USB
2.0 sur cette carte mère. Chaque embase USB 2.0 peut prendre en charge 2 ports USB 2.0.
(voir p.2 No. 27)
Français
USB_PWR
P-9
P+9
GND
DUMMY
(USB_8_9 br.9)
(voir p.2 No. 28)
1
GND
P+8
P-8
USB_PWR
48
ASRock 970 Extreme3 R2.0 Motherboard
En-tête du module infrarouge
(IR1 br.5)
Cet en-tête supporte un module infrarouge optionnel de (voir p.2 No. 29)
transfert et de réception sans fil.
Barrette pour module à infrarouges grand public
(CIR1 br.4)
Cette barrette peut être utilisée pour connecter des récepteur
(voir p.2 No. 25)
Connecteur audio panneau (HD_AUDIO1 br. 9)
(voir p.2 No. 32)
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
C’est une interface pour
un câble avant audio en façade qui permet le branchement et le contrôle commodes de
périphériques audio.
1. L’audio à haute définition (HDA) prend en charge la détection de fiche, mais le fil de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de châssis afin installer votre système.
2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio du panneau avant conformément à la procédure ci-dessous :
A. Connectez Mic_IN (MIC) à MIC2_L.
B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L.
C. Connectez Ground (GND) à Ground (GND).
D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous n’avez pas besoin de les connecter pour le panneau audio AC’97.
E. Pour activer le micro avant.
Pour les systèmes d’exploitation Windows® XP / XP 64 bits :
Sélectionnez “Mixer”. Sélectionnez “Recorder” (Enregistreur). Puis cliquez sur “FrontMic” (Micro avant).
Pour les systèmes d’exploitation Windows® 8 / 8 64 bits / 7 / 7 64 bits / VistaTM /
VistaTM 64 bits :
Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).
En-tête du panneau système (PANEL1 br.9)
(voir p.2 No. 23)
Cet en-tête permet d’utiliser plusieurs fonctions du panneau système frontal.
ASRock 970 Extreme3 R2.0 Motherboard
Français
GND
PRESENCE#
MIC_RET
OUT_RET
49
Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et l’indicateur d’état du système du châssis sur cette barrette en respectant
l’affectation des broches décrite ci-dessous. Faites attention aux broches positives et négatives avant de connecter les câbles.
PWRBTN (Interrupteur d’alimentation):
Connectez ici le connecteur d’alimentation sur le panneau avant du châssis. Vous pouvez configurer la façon de mettre votre système hors tension avec l’interrupteur d’alimentation.
RESET (Interrupteur de réinitialisation):
Connectez ici le connecteur de réinitialisation sur le panneau avant du châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.
PLED (DEL alimentation système):
Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le système est en marche. Levoyant DEL clignote lorsque le système est en mode veille S1. Le voyant DEL est éteint lorsque le système est en mode veille S3/
S4 ou lorsqu’il est éteint (S5).
HDLED (DEL activité du disque dur):
Connectez ici le voyant DEL d’activité du disque dur sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en train de lire ou d’écrire des données.
Le design du panneau avant peut varier en fonction du châssis. Un module de panneau avant consiste principalement en : interrupteur d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation, voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous connectez le panneau avant de votre châssis sur cette barrette, vérifiez bien à faire correspondre les fils et les broches.
En-tête du haut-parleur de châssis
(SPEAKER1 br. 4)
Veuillez connecter le
haut-parleur de châssis sur cet en-tête.
(voir p.2 No. 24)
Français
LED di accensione
Collegare il LED di accensione (3-pin PLED1)
chassi per indicare lo stato di alimentazione del sistema. Il LED è acceso quando il sistema
è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
(vedi p.2 Nr. 22)
50
ASRock 970 Extreme3 R2.0 Motherboard
Connecteur pour châssis et ventilateur
(CHA_FAN1 br. 4)
(voir p.2 No. 12)
(CHA_FAN2 br. 3)
(voir p.2 No. 15)
GND
+12V
CHA_FAN_SPEED
Branchez les câbles du
ventilateur aux connecteurs pour
ventilateur et faites correspondre
le fil noir à la broche de terre. La
vitesse des ventilateurs CHA_
FAN1/2/3 peut être réglée avec
UEFI ou AXTU.
(CHA_FAN3 br. 3)
(voir p.2 No. 2)
(PWR_FAN1 br. 3)
(voir p.2 No. 10)
Connecteur du ventilateur de l’UC
(CPU_FAN1 br. 4)
(voir p.2 No. 6)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Veuillez connecter le câble de ventilateur d’UC sur ce connecteur et brancher le fil noir sur la broche de terre.
Bien que cette carte mère offre un support de (Ventilateur silencieux
ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut bien fonctionner même sans la fonction de commande de vitesse du ventilateur.Si vous prévoyez de connecter le ventilateur de CPU à 3
broches au connecteur du ventilateur de CPU sur cette carte mère,
veuillez le connecter aux broches 1-3.
Installation de ventilateur à 3 broches
Broches 1-3 connectées
(CPU_FAN2 br. 3)
GND
+12V
CPU_FAN_SPEED
En-tête d’alimentation ATX
(ATXPWR1 br. 24)
(voir p.2 No. 9)
12
24
1
13
Veuillez connecter l’unité d’alimentation ATX sur cet en-
tête.
Bien que cette carte mère fournisse un connecteur de
courant ATX 24 broches, elle peut encore fonctionner
si vous adopter une alimentation traditionnelle ATX 20
broches. Pour utiliser une alimentation ATX 20 broches,
branchez à l’alimentation électrique ainsi qu’aux
broches 1 et 13.
20-Installation de l’alimentation électrique ATX
ASRock 970 Extreme3 R2.0 Motherboard
12
24
1
13
Français
(voir p.2 No. 5)
51
Connecteur ATX 12V
(ATX12V1 br.8)
5
1
Veuillez connecter une unité d’alimentation électrique ATX (voir p.2 No. 1)
8
4
12V sur ce connecteur.
Bien que cette carte mère possède 8 broches connecteur d’alimentation ATX 12V, il peut toujours travailler si vous adoptez une approche traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser
l’alimentation des 4 broches ATX, branchez votre alimentation
5
1
avec la broche 1 et la broche 5.
4-Installation d’alimentation à 4 broches ATX 12V
En-tête de port COM
(COM1 br.9)
4
(voir p.2 No. 30)
Cette en-tête de port COM est utilisée pour prendre en charge un module de port COM.
Connecteur HDMI_SPDIF
(HDMI_SPDIF1 2-pin)
(voir p.2 No. 31)
Connecteur HDMI_SPDIF, fournissant une sortie audio SPDIF vers la carte VGA HDMI, et permettant au système
de se connecter au un
téléviseur numérique HDMI /un
projecteur / un périphérique
LCD. Veuillez brancher le
connecteur HDMI_SPDIF de la
carte VGA HDMI sur ce
connecteur.
Français
En-tête USB 3.0
(USB3_2_3 br. 19)
(voir p.2 No. 38)
52
8
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
En plus des deux ports USB
3.0 par défaut sur le panneau
E/S, il y a une barrette USB 3.0
sur la carte mère. Cette barrette
USB 3.0 peut prendre en
charge deux ports USB 3.0.
ASRock 970 Extreme3 R2.0 Motherboard
2. Informations sur le BIOS
La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous
démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-OnSelf-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si
vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en
pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier
du système. Vous pouvez également redémarrer en éteignant le système et en le
rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un
programme piloté par menu, qui vous permet de faire défiler par ses divers sousmenus et de choisir parmi les choix prédéterminés. Pour des informations détaillées
sur le BIOS, veuillez consulter le Guide de l’utilisateur (fichier PDF) dans le CD
technique.
3. Informations sur le CD de support
Français
Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®:
8 / 8 64 bits / 7 / 7 64 bits / VistaTM / VistaTM 64 bits / XP / XP 64 bits. Le CD technique livré avec cette carte mère contient les pilotes et les utilitaires nécessaires
pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérezle dans le lecteur de CD-ROM. Le Menu principal s’affiche automatiquement si
“AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas
automatiquement, localisez dans le CD technique le fichier “ASSETUP.EXE” dans le
dossier BIN et double-cliquez dessus pour afficher les menus.
ASRock 970 Extreme3 R2.0 Motherboard
53
1. Introduzione
Grazie per aver scelto una scheda madre ASRock 970 Extreme3 R2.0, una scheda
madre affidabile prodotta secondo i severi criteri di qualità ASRock. Le prestazioni
eccellenti e il design robusto si conformano all’impegno di ASRock nella ricerca
della qualità e della resistenza.
Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la
guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si
possono trovare nel manuale per l’utente presente nel CD di supporto.
Le specifiche della scheda madre e il software del BIOS possono essere aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia modificato, la versione aggiornata sarà disponibile sul sito di ASRock senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate.
ASRock website http://www.asrock.com
Se si necessita dell’assistenza tecnica per questa scheda madre, visitare il nostro sito per informazioni specifiche sul modello che si sta usando.
www.asrock.com/support/index.asp
1.1 Contenuto della confezione
Scheda madre ASRock 970 Extreme3 R2.0 (ATX Form Factor)
Guida di installazione rapida ASRock 970 Extreme3 R2.0
CD di supporto ASRock 970 Extreme3 R2.0
Due cavi dati Serial ATA (SATA) (opzionali)
Un I/O Shield
ASRock vi ricorda...
Per ottenere migliori prestazioni in Windows® 8 / 8 64-bit / 7 / 7 64-bit /
VistaTM / VistaTM 64-bit, si consiglia di impostare l'opzione BIOS in Storage
Configuration (Configurazione di archiviazione) sulla modalità AHCI. Per
l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'utente) nel CD di supporto per dettagli.
Italiano
54
ASRock 970 Extreme3 R2.0 Motherboard
1.2 Specifiche
Processore
Chipset
Memoria
Slot di
espansione
Audio
LAN
- ATX Form Factor
- Design condensatore compatto (condensatori a conduttore in polimero di alta qualità realizzati al 100% in Giappone)
- Supporto di processori Socket AM3+
- Supporto di processori Socket AM3: AMD PhenomTM II X6 / X4
/ X3 / X2 (fatta eccezione per 920 / 940) / Athlon II X4 / X3 / X2
/ Sempron
- CPU Otto-Core Ready
- Supporto UCC (Unlock CPU Core)
- Design Digi Power
- Struttura di fase con alimentazione 4 + 1
- Supporta CPU fino a 140 W
- Supporto tecnologia AMD Cool ‘n’ QuietTM
- FSB 2400 MHz (4.8 GT/s)
- Supporta la tecnologia overclocking “slegata”
- Supporta la tecnologia Hyper-Transport 3.0 (HT 3.0)
- Northbridge: AMD 970
- Southbridge: AMD SB950
- Supporto tecnologia Dual Channel Memory
- 4 x slot DDR3 DIMM
- Supporto DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/
1333/1066/800 non-ECC, momoria senza buffer
- Capacità massima della memoria di sistema: 32GB
- 2 x alloggiamenti PCI Express 2.0 x16
(PCIE2: modalità x16; PCIE4: modalità x4)
- 2 x slot PCI Express 2.0 x1
- 2 x slot PCI
- Supporto di AMDTM Quad CrossFireXTM e CrossFireXTM
- 7.1 CH HD Audio con protezioni contenuti
(Realtek ALC892 Audio Codec)
- Supporto audio Blu-ray Premium
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supporta Wake-On-LAN
- Supporta il rilevamento cavo LAN
- Supporto di Energy Efficient Ethernet 802.3az
- Supporta PXE
ASRock 970 Extreme3 R2.0 Motherboard
Italiano
Piattaforma
55
Italiano
Pannello
posteriore
I/O
SATA3
USB 3.0
Connettori
BIOS 56
I/O Panel
- 1 x porta PS/2 per mouse
- 1 x porta PS/2 per tastiera
- 1 x Porta coassiale SPDIF Out
- 1 x Porta ottica SPDIF Out
- 4 x porte USB 2.0 già integrate
- 2 x porte USB 3.0 già integrate
- 1 x Connettore eSATA3
- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e
LED velocità)
- Connettore HD Audio: cassa laterale / cassa posteriore /
cassa centrale / bassi / ingresso linea / cassa frontale /
microfono
- 5 x connettori SATA3 6,0 Gb/s, supporto di RAID (RAID 0,
RAID 1, RAID 5 e RAID 10) e delle funzioni NCQ, AHCI e “Hot
Plug”
- 2 x porte USB 3.0 posteriori amministrate dal controller
Etron EJ188H, supporto di USB 1.1/2.0/3.0 fino a 5Gb/s
- 1 x header USB 3.0 frontale (supporta 2 porte USB 3.0) amministrato dal controller Etron EJ188H, supporto di USB
1.1/2.0/3.0 fino a 5Gb/s
- 5 x connettori SATA3 6.0Go/s
- 1 x Collettore modulo infrarossi
- 1 x Connettore modulo infrarosso consumer
- 1 x collettore porta COM
- 1 x Header HDMI_SPDIF
- 1 x LED di accensione
- 2 x Connettore CPU ventola (1 x 4-pin, 1 x 3-pin)
- 3 x Connettore Chassis ventola (1 x 4-pin, 2 x 3-pin)
- 1 x Connettore Alimentazione ventola (3-pin)
- 24-pin collettore alimentazione ATX
- 8-pin connettore ATX 12V
- Connettore audio sul pannello frontale
- 3 x Collettore USB 2.0 (supporta 6 porte USB 2.0)
- 1 x Collettore USB 3.0 (supporta 2 porte USB 3.0)
- 32Mb AMI UEFI Legal BIOS con interfaccia di supporto
- Supporta “Plug and Play”
- Compatibile con ACPI 1.1 wake up events
- Supporta jumperfree
- Supporta SMBIOS 2.3.1
- Regolazione multi-voltaggio CPU, VCCM, NB, SB
ASRock 970 Extreme3 R2.0 Motherboard
CD di supporto
Monitoraggio
Hardware
Compatibi-
lità SO
Certificazioni
- Driver, utilità, software antivirus (Versione dimostrativa),
CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser
e Toolbar
- Sensore per la temperatura del processore
- Sensore temperatura scheda madre
- Indicatore di velocita per la ventola del CPU/Chassis/
Alimentazione
- Ventola CPU/chassis silenziosa
- Ventola CPU/chassis con controllo di varie velocità
- Voltaggio: +12V, +5V, +3.3V, Vcore
- Microsoft® Windows® 8 / 8 64 bit / 7 / 7 64 bit / VistaTM / VistaTM
64 bit / XP / XP 64 bit
- FCC, CE, WHQL
- Predisposto ErP/EuP (è necessaria l’alimentazione predis
posta per il sistema ErP/EuP)
Italiano
* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com
ASRock 970 Extreme3 R2.0 Motherboard
57
1.3 Setup dei Jumpers
L’illustrazione mostra come sono settati i jumper. Quando il ponticello è posizionato sui pin,
il jumper è “CORTOCIRCUITATO”. Se sui pin
non ci sono ponticelli, il jumper è “APERTO”.
L’illustrazione mostra un jumper a 3 pin in cui il
pin1 e il pin2 sono “CORTOCIRCUITATI” quando il ponticello è posizionato su questi pin.
Jumper Settaggio del Jumper
Resettare la CMOS
(CLRCMOS1)
(vedi p.2 item 21)
Impostazione
predefinita
Azzeramento CMOS
Nota:CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare
i parametri del sistema sulla configurazione iniziale, spegnere il computer e
scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi,
poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su
CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS
subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si
è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare
il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. Notare che password, data, ore, profilo utente predefinito, 1394 GUID e indirizzo
MAC saranno cancellati solo se è rimossa la batteria della CMOS.
Italiano
58
ASRock 970 Extreme3 R2.0 Motherboard
1.4 Collettori e Connettori su Scheda
I collettori ed i connettori su scheda NON sono dei jumper. NON installare cappucci per jumper su questi collettori e connettori. L’installazione
di cappucci per jumper su questi collettori e connettori provocherà
danni permanenti alla scheda madre!
Connettori Serial ATA3
(SATA3_1: vedi p.2 Nr. 17) (SATA3_2: vedi p.2 Nr. 18) (SATA3_3: vedi p.2 Nr. 16)
(SATA3_4: vedi p.2 Nr. 19) SATA3_5
(SATA3_5: vedi p.2 Nr. 20)
SATA3_3
SATA3_1
SATA3_4
SATA3_2
Questi cinque connettori Serial
ATA3 (SATA3) supportano cavi dati SATA per dispositivi di immagazzinamento interni.
ATA3 (SATA3) supportano cavi SATA per dispositivi di memoria interni. L’interfaccia SATA3 attuale permette velocità di trasferimento dati fino a
6.0 Gb/s.
Cavi dati Serial ATA (SATA) (Opzionale)
Una o altra estremità del cavo di dati SATA può essere collegata al disco rigido SATA / SATAII / SATA3 o al connettore di SATAII / SATA3 su questa cartolina base.
Collettore USB 2.0
(9-pin USB_4_5)
(vedi p.2 Nr. 26)
Oltre alle quattro porte USB 2.0
predefinite nel pannello I/O, la scheda madre dispone di tre intestazioni USB 2.0. Ciascuna intestazione USB 2.0 supporta due porte USB 2.0.
Italiano
(9-pin USB_6_7)
(vedi p.2 Nr. 27)
USB_PWR
P-9
P+9
GND
DUMMY
(9-pin USB_8_9)
(vedi p.2 Nr. 28)
1
GND
P+8
P-8
USB_PWR
ASRock 970 Extreme3 R2.0 Motherboard
59
Collettore modulo infrarossi
(5-pin IR1)
(vedi p.2 Nr. 29)
Questo collettore supporta moduli ad infrarossi optional per la trasmissione e la ricezione senza fili.
Connettore modulo infrarosso consumer
(4-pin CIR1)
(vedi p.2 Nr. 25)
Questo connettore può essere
utilizzato per collegare
ricevitore remoto.
Connettore audio sul pannello frontale
(9-pin HD_AUDIO1) (vedi p.2 Nr. 32)
È un’interfaccia per il cavo del
pannello audio. Che consente connessione facile e controllo
dei dispositivi audio.
GND
PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
Italiano
1. La caratteristica HDA (High Definition Audio) supporta il rilevamento dei connettori, però il pannello dei cavi sul telaio deve supportare la funzione HDA (High Definition Audio) per far sì che questa operi in modo corretto. Attenersi alle istruzioni del nostro manuale e del manuale del telaio per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio del pannello anteriore, come indicato di seguito:
A. Collegare Mic_IN (MIC) a MIC2_L.
B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L.
C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97.
E. Per attivare il microfono frontale.
Sistema operativo Windows® XP / XP 64-bit:
Selezionare “Mixer”. Selezionare “Recorder” (Registratore). Poi, fare clic su “FrontMic” (Microfono frontale).
Sistema operativo Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM
64-bit:
Andare alla scheda “FrontMic” (Microfono frontale) del pannello di
controllo Realtek. Regolare la voce “Recording Volume” (Volume registrazione).
Collettore pannello di sistema
(9-pin PANEL1)
(vedi p.2 Nr. 23)
60
Questo collettore accomoda diverse funzioni di sistema pannello frontale.
ASRock 970 Extreme3 R2.0 Motherboard
Collegare l’interruttore d’alimentazione, l’interruttore di ripristino,
l’indicatore di stato del sistema del pannello frontale del telaio a questo header in base all’assegnazione dei pin definita di seguito. Determinare i pin positivi e negativi prima di collegare i cavi.
PWRBTN (interruttore d’alimentazione):
Va collegato all’interruttore d’alimentazione del pannello frontale del
telaio. Usando l’interruttore d’alimentazione si può configurare il modo in cui si spegne il sistema.
RESET (interruttore di ripristino):
Va collegato all’interruttore di ripristino del pannello frontale del telaio. Premere l’interruttore di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.
PLED (LED alimentazione del sistema):
Va collegato all’indicatore di stato d’alimentazione del pannello frontale del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua a lampeggiare quando il sistema è in stato di standby S1. Il LED è
spento quando il sistema è in stato di sospensione /ibernazione S3/S4 oppure spento (S5).
HDLED (LED attività disco rigido):
Va collegato al LED attività disco rigido del pannello frontale del telaio. Il LED è acceso quando disco rigido legge e scrive i dati.
Il design del pannello frontale può variare in base ai telai. Il modulo di un pannello frontale può consistere di: interruttore d’alimentazione,
interruttore di ripristino, LED d’alimentazione, LED attività disco rigido, casse, eccetera. Quando si collega il modulo del pannello frontale a
questo header, assicurarsi che l’assegnazione dei fili e dei pin sia fatta corrispondere in modoappropriato.
Collettore casse telaio
(4-pin SPEAKER1)
Collegare le casse del telaio a questo collettore.
(vedi p.2 Nr. 24)
Collegare il LED di accensione chassi per indicare lo stato di alimentazione del sistema. Il
LED è acceso quando il sistema
è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
ASRock 970 Extreme3 R2.0 Motherboard
Italiano
LED di accensione
(3-pin PLED1)
(vedi p.2 Nr. 22)
61
Collettori Chassis ed alimentazione ventola
(4-pin CHA_FAN1)
Collegare i cavi della ventola ai corrispondenti connettori (vedi p.2 Nr. 12)
facendo combaciare il cavo nero col pin di terra. La velocità
della ventola CHA_FAN1/2/3
può essere controllata tramite
UEFI o AXTU.
(3-pin CHA_FAN2)
GND
+12V
CHA_FAN_SPEED
(vedi p.2 Nr. 15)
(3-pin CHA_FAN3)
(vedi p.2 Nr. 2)
(3-pin PWR_FAN1)
(vedi p.2 Nr. 10)
Connettore ventolina CPU
(4-pin CPU_FAN1)
(vedi p.2 Nr. 6)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Collegare il cavo della ventolina CPU a questo connettore e far combaciare il filo nero al pin terra.
Sebbene la presente scheda madre disponga di un supporto per ventola CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in grado di funzionare anche senza la funzione di controllo della velocità della ventola. Se si intende collegare la ventola CPU a 3 piedini al
connettore della ventola CPU su questa scheda madre, collegarla ai piedini 1-3.
Piedini 1-3 collegati
Installazione della ventola a 3 piedini
(3-pin CPU_FAN2)
GND
+12V
CPU_FAN_SPEED
(vedi p.2 Nr. 5)
Italiano
Connettore alimentazione ATX
(24-pin ATXPWR1)
(vedi p.2 Nr. 9)
62
12
24
1
13
Collegare la sorgente d’alimentazione ATX a questo connettore.
ASRock 970 Extreme3 R2.0 Motherboard
Con questa scheda madre, c’è in dotazione un
connettore elettrico ATX a 24 pin, ma può funzionare lo
stesso se si adotta un alimentatore ATX a 20 pin. Per
usare l’alimentatore ATX a 20 pin, collegare l’alimentatore
con il Pin 1 e il Pin 13.
12
24
Installazione dell’alimentatore ATX a 20 pin 1
13
5
1
(vedi p.2 Nr. 1)
8
4
Collegare un alimentatore ATX 12 V a questo connettore.
Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX 12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura
1
elettrica 4-pin ATX 12V, prego collegare la presa elettrica 5
al Pin 1 e Pin 5.
Installazione elettrica 4-Pin ATX 12V
Collettore porta COM
(9-pin COM1)
8
4
(vedi p.2 Nr. 30)
Questo collettore porta COM è utilizzato per supportare il modulo porta COM.
Header HDMI_SPDIF (2-pin HDMI_SPDIF1)
(vedi p.2 Nr. 31)
Header HDMI_SPDIF, con uscita audio SPDIF su scheda HDMI VGA, consente al sistema di collegare dispositivi per TV digitale HDMI/proiettori/
LCD . Collegare il connettore HDMI_SPDIF della scheda VGA HDMI a questo header.
Collettore USB 3.0
(19-pin USB3_2_3)
(vedi p.2 Nr. 38)
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
Italiano
Connettore ATX 12 V
(8-pin ATX12V1)
Oltre alle due porte USB 3.0
standard del pannello I/O,
questa scheda madre è dotata
di un header USB 3.0 che
supporta due porte USB 3.0.
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
ASRock 970 Extreme3 R2.0 Motherboard
63
2. Informazioni sul BIOS
La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il
computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup
utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il
BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o
premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa
il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF file) contenuto nel cd
di supporto.
3. Software di supporto e informazioni su
CD
Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 8 / 8 64bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Il CD di supporto a corredo
della scheda madre contiene i driver e utilità necessari a potenziare le caratteristiche della scheda.
Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata
nel computer, apparirà automaticamente il Menù principale. Se il Menù principale
non appare automaticamente, posizionarsi sul file “ASSETUP.EXE” nel CESTINO
del CD di supporto e cliccare due volte per visualizzare i menù.
Italiano
64
ASRock 970 Extreme3 R2.0 Motherboard
1. Introducción
Gracias por su compra de ASRock 970 Extreme3 R2.0 placa madre, una placa de
confianza producida bajo el control de calidad estricto y persistente. La placa madre
provee realización excelente con un diseño robusto conforme al compromiso de
calidad y resistencia de ASRock.
Esta Guía rápida de instalación contiene una introducción a la placa base y una
guía de instalación paso a paso. Puede encontrar una información más detallada
sobre la placa base en el manual de usuario incluido en el CD de soporte.
Porque las especificaciones de la placa madre y el software de BIOS podrían ser actualizados, el contenido de este manual puede ser cambiado sin aviso. En caso de cualquier modificación de este manual, la versión actualizada estará disponible en el website de ASRock sin previo aviso. También encontrará las listas de las últimas tarjetas VGA y CPU soportadas en la página web de ASRock.
Website de ASRock http://www.asrock.com
Si necesita asistencia técnica en relación con esta placa base, visite nuestra página web con el número de modelo específico de su placa.
www.asrock.com/support/index.asp
1.1 Contenido de la caja
Placa base ASRock 970 Extreme3 R2.0 (Factor forma ATX)
Guía de instalación rápida de ASRock 970 Extreme3 R2.0
CD de soporte de ASRock 970 Extreme3 R2.0
Dos cables de datos Serial ATA (SATA) (Opcional)
Una protección I/O
ASRock le recuerda...
Español
Para mejorar el rendimiento en Windows® 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / VistaTM 64 bits, es recomendable establecer la opción del BIOS de
la configuración de almacenamiento en el modo AHCI. Para obtener detalles sobre la configuración del BIOS, consulte el “Manual del usuario”
que se encuentra en nuestro CD de soporte.
ASRock 970 Extreme3 R2.0 Motherboard
65
1.2 Especificación
Plataforma
Español
Procesador
Chipset
Memoria Ranuras de Expansión
Audio
LAN
66
- Factor forma ATX
- Todo diseño de Capacitor Sólido (condensadores de
polímero conductor de alta calidad 100% fabricados en
Japón)
- Compatibilidad con procesadores con conector AM3+
- Compatibilidad con procesadores con conector AM3: procesador AMD PhenomTM II X6 / X4 / X3 / X2 (excepto 920
/ 940) / Athlon II X4 / X3 / X2 / Sempron
- Compatible con CPU de ocho núcleo
- Con soporte UCC (Unlock CPU Core)
- Diseño de alimentación digital
- Diseño de fases de potencia 4 + 1
- Compatible con CPU de hasta 140W
- Con soporte para tecnología Cool ‘n’ QuietTM de AMD
- FSB 2400 MHz (4.8 GT/s)
- Admite tecnología de aumento de velocidad liberada
- Soporta Tecnología de Hiper-Transporte 3.0 (HT 3.0)
- North Bridge: AMD 970
- South Bridge: AMD SB950
- Soporte de Tecnología de Memoria de Doble Canal
- 4 x DDR3 DIMM slots
- Apoya DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/
1333/1066/800 non-ECC, memoria de un-buffered
- Máxima capacidad de la memoria del sistema: 32GB
- 2 x ranuras PCI Express 2.0 x16
(PCIE2: modo x16; PCIE4: modo x4)
mode o dobles en modo x8 / x8; PCIE5: modo x4)
- 2 x ranura PCI Express 2.0 x1
- 2 x ranuras PCI
- Soporta AMDTM Quad CrossFireXTM y CrossFireXTM
- 7.1 CH HD Audio con Protección de Contenido
(Realtek ALC892 Audio Codec)
- Compatible con audio Blu-ray de alta calidad
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Soporta Wake-On-LAN
- Admite detección de conexión de cable LAN
- Compatible con Ethernet 802.3az de bajo consumo
ASRock 970 Extreme3 R2.0 Motherboard
ASRock 970 Extreme3 R2.0 Motherboard
Español
energético
- Admite PXE
Entrada/Salida
I/O Panel de Panel - 1 x puerto de ratón PS/2
Trasero - 1 x puerto de teclado PS/2
- 1 x puerto de salida coaxial SPDIF
- 1 x puerto de salida óptica SPDIF
- 4 x puertos USB 2.0 predeterminados
- 2 x puertos USB 3.0 predeterminados
- 1 x Conector eSATA3
- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/
ENLACE y LED de VELOCIDAD)
- Conexión de audio: Altavoz lateral / Altavoz trasero /
Central/Bajos / Entrada de línea / Altavoz frontal /
Micrófono
SATA3 - 5 x conectores SATA3 de 6,0 Gb/s compatibles con
funciones RAID (RAID 0, RAID 1, RAID 5 y RAID 10),
NCQ, AHCI y de “conexión en caliente” compatibles con
funciones NCQ, AHCI y de “conexión en caliente”
USB 3.0 - 2 x puertos USB 3.0 traseros de Etron EJ188H,
compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s
- 1 x cabecera USB 3.0 delantera (compatible con 2 puertos USB 3.0) de Etron EJ188H, compatible con USB 1.1/2.0/3.0
de hasta 5 GB/s
Conectores - 5 x conexiones SATA3, admiten una velocidad de transferencia de datos de hasta 6,0Gb/s
- 1 x Cabezal de Módulo Infrarrojos
- 1 x Base de conexiones del módulo de infrarrojos para el
consumidor
- 1 x En-tête de port COM
- 1 x cabecera HDMI_SPDIF
- 1 x cabecera de indicador LED de encendido
- 2 x Conector de ventilador de CPU (1 x 4-pin, 1 x 3-pin)
- 3 x Conector de ventilador de chasis (1 x 4-pin, 2 x 3-pin)
- 1 x Conector de ventilador de alimentacion (3-pin)
- 24-pin cabezal de alimentación ATX
- 8-pin conector de ATX 12V power
- Conector de audio de panel frontal
- 3 x Cabezal USB 2.0 (admite 6 puertos USB 2.0
adicionales)
- 1 x Cabezal USB 3.0 (admite 2 puertos USB 3.0
adicionales)
67
BIOS CD de soport Monitor Hardware
OS
Certificaciones
- 32Mb AMI BIOS legal UEFI AMI compatible con GUI
- Soporta “Plug and Play”
- ACPI 1.1 compliance wake up events
- Soporta “jumper free setup”
- Soporta SMBIOS 2.3.1
- Múltiple ajuste de CPU, VCCM, NB, SB Voltage
- Controladores, Utilerías, Software de Anti Virus (Versión de prueba), Prueba de CyberLink MediaEspresso 6.5,
Google Chrome Browser y Toolbar
- Sensibilidad a la temperatura del procesador
- Sensibilidad a la temperatura de la placa madre
- Taquimetros de los ventiladores del procesador y del CPU / chasis / alimentacion
- Ventilador silencioso para CPU y el chasis
- Control de ajuste de la velocidad del ventilador de la CPU
y el chasis
- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore
- En conformidad con Microsoft® Windows® 8 / 8 64 bits / 7 /
7 64 bits / VistaTM / VistaTM 64 bits / XP / XP 64 bits
- FCC, CE, WHQL
- Cumple con la directiva ErP/EuP (se requiere una fuente
de alimentación que cumpla con la directiva ErP/EuP)
* Para más información sobre los productos, por favor visite nuestro sitio web:
http://www.asrock.com
Español
68
ASRock 970 Extreme3 R2.0 Motherboard
1.3 Setup de Jumpers
La ilustración muestra como los jumpers
son configurados. Cuando haya un jumpercap sobre los pins, se dice gue el jumper
está “Short”. No habiendo jumper cap sobre
los pins, el jumper está “Open”. La ilustración muesta un jumper de 3 pins cuyo
pin 1 y pin 2 están “Short”.
Jumper
Limpiar CMOS
Setting
(CLRCMOS1, jumper de 3 pins)
(ver p.2, No. 21)
Valor predeterminado
Restablecimiento de
la CMOS
Español
Nota:CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los
parámetros del sistema y restablecer la configuración predeterminada de los mismos,
apague el equipo y desenchufe el cable de alimentación de la toma de corriente
eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente para
cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre
la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar
la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero
el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de
dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perfil
predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se
borrará si la batería CMOS se quita.
ASRock 970 Extreme3 R2.0 Motherboard
69
1.4 Cabezales y Conectores en Placas
Los conectores y cabezales en placa NO son puentes. NO coloque
las cubiertas de los puentes sobre estos cabezales y conectores. El
colocar cubiertas de puentes sobre los conectores y cabezales provocará un daño permanente en la placa base.
Conexiones de serie ATA3
(SATA3_1: vea p.2, N. 17) (SATA3_2: vea p.2, N. 18) (SATA3_3: vea p.2, N. 16) (SATA3_4: vea p.2, N. 19) SATA3_5
(SATA3_5: vea p.2, N. 20)
SATA3_3
SATA3_1
SATA3_4
SATA3_2
Estas cinco conexiones de serie ATA3 (SATA3) admiten cables SATA para dispositivos de almacenamiento internos. La
interfaz SATAII / SATA3 actual permite una velocidad de transferencia de 6.0 Gb/s.
Cable de datos de serie ATA (SATA)
(Opcional)
Cualquier extremo del cable de los datos de SATA puede ser conectado con el disco duro de SATA / SATAII / SATA3 o el conectador de SATAII / SATA3 en esta placa base.
Cabezal USB 2.0 (9-pin USB_4_5)
(vea p.2, N. 26) (9-pin USB_6_7)
Además de cuatro puertos
USB 2.0 predeterminados en el panel de E/S, hay tres bases de conexiones USB 2.0 en esta placa base. Cada una de
estas bases de conexiones admite dos puertos USB 2.0.
(vea p.2, N. 27)
Español
USB_PWR
P-9
P+9
GND
DUMMY
(9-pin USB_8_9)
(vea p.2, N. 28)
1
GND
P+8
P-8
USB_PWR
70
ASRock 970 Extreme3 R2.0 Motherboard
Cabezal de Módulo Infrarrojos
(5-pin IR1)
Este cabezal soporta un módulo infrarrojos de transmisión y recepción wireless opcional.
Base de conexiones del módulo de infrarrojos para el consumidor
(4-pin CIR1)
Esta base de conexiones se
puede utilizar para conectar receptor remoto.
(vea p.2, N. 29)
(vea p.2, N. 25)
Conector de audio de
panel frontal
(9-pin HD_AUDIO1) (vea p.2, N. 32) PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
Este es una interface para cable de audio de panel frontal que permite conexión y control conveniente de apparatos de Audio.
1. El Audio de Alta Definición soporta la detección de conector, pero el cable de panel en el chasis debe soportar HDA para operar
correctamente. Por favor, siga las instrucciones en nuestro manual y en el manual de chasis para instalar su sistema.
2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido del panel frontal de la siguiente manera:
A. Conecte Mic_IN (MIC) a MIC2_L.
B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L.
C. Conecte Ground (GND) a Ground (GND).
D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No necesitará conectarlos al panel de sonido AC’97.
E. Activación del micrófono frontal.
En sistemas operativos Windows® XP / XP 64-bit:
Seleccione “Mixer” (Mezclador). Seleccione “Recorder” (Grabadora). A continuación, haga clic en “FrontMic” (Micrófono frontal).
En sistemas operativos Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit:
Acceda a la ficha “FrontMic” (Micrófono frontal) del panel de control Realtek. Ajuste la posición del control deslizante “Recording Volume” (Volumen de grabación).
Cabezal de panel de sistema
(9-pin PANEL1)
(vea p.2, N. 23) Español
GND
Este cabezar acomoda varias dunciones de panel frontal de sistema.
ASRock 970 Extreme3 R2.0 Motherboard
71
Conecte el interruptor de alimentación, el interruptor de restablecimiento y el indicador de estado del sistema situados en el chasis con esta cabecera en función de las siguientes asignaciones de contacto. Preste atención a los contactos positivos y negativos antes de conectar los cables.
PWRBTN (interruptor de alimentación):
Conecte el interruptor de encendido situado en el panel frontal del
chasis. Puede configurar la forma de apagar su sistema mediante el interruptor de alimentación.
RESTABLECER (interruptor de restablecimiento):
Conecte el interruptor de restablecimiento situado en el panel frontal del chasis. Pulse el interruptor de restablecimiento para restablecer el equipo si se bloquea y no se reinicia con normalidad.
PLED (LED de alimentación del sistema):
Conecte el indicador de estado de alimentación situado en el panel
frontal del chasis. El LED se enciende cuando el sistema esté en
funcionamiento. El LED parpadea cuando el sistema se encuentre en estado de suspensión S1. El LED se apaga cuando el sistema se
encuentre en estado de suspensión S3/S4 o se apaga (S5).
HDLED (LED de actividad del disco duro):
Conecte el LED de actividad de disco duro situado en el panel frontal del chasis. El LED se enciende cuando el disco duro esté leyendo o escribiendo datos.
Es posible que el diseño del panel frontal varíe en función del chasis. Un módulo del panel frontal consiste principalmente de interruptor de
alimentación, interruptor de restablecimiento, LED de alimentación, LED
de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel frontal del chasis a esta cabecera, asegúrese de que las asignaciones de cables y las asignaciones de contactos coincidan correctamente.
Cabezal del altavoz del chasis
(4-pin SPEAKER1)
Conecte el altavoz del chasis a su cabezal.
(vea p.2, N. 24)
Español
72
Cabecera de indicador LED de encendido
(3-pin PLED1)
Conecte el indicador LED de encendido del chasis a esta (vea p.2, N. 22) cabecera para conocer el
estado de encendido del sistema. El indicador LED se encenderá si el sistema se
encuentra en funcionamiento. El indicador LED parpadeará en el estado S1. El indicador LED se apagará en los estados S3/S4 o S5 (apagado).
ASRock 970 Extreme3 R2.0 Motherboard
Conectores de ventilador de chasis
y alimentación
(4-pin CHA_FAN1)
Por favor, conecte los cables
del ventilador a los conectores
de ventilador, haciendo coincidir
el cable negro con la patilla de
masa. La velocidad del ventilador CHA_FAN1/2/3 se puede
controlar mediante UEFI o
AXTU.
(vea p.2, N. 12)
GND
+12V
CHA_FAN_SPEED
(3-pin CHA_FAN2)
(vea p.2, N. 15)
(3-pin CHA_FAN3)
(vea p.2, N. 2)
(3-pin PWR_FAN1)
(vea p.2, N. 10)
Conector del ventilador de la CPU
(4-pin CPU_FAN1)
(vea p.2, N. 6)
Conecte el cable del ventilador de la CPU a este conector y haga coincidir el cable negro con el conector de tierra.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Aunque esta placa base proporciona compatibilidad para un ventilador (silencioso) de procesador de 4 contactos, el ventilador de procesador de 3 contactos seguirá funcionando correctamente incluso sin la función de control de velocidad del ventilador. Si pretende enchufar el ventilador de procesador de 3 contactos en el conector del ventilador de
procesador de esta placa base, conéctelo al contacto 1-3.
Contacto 1-3 conectado
Instalación del ventilador de 3 contactos
(3-pin CPU_FAN2)
GND
+12V
CPU_FAN_SPEED
Cabezal de alimentación ATX
(24-pin ATXPWR1)
12
24
1
13
Conecte la fuente de alimentación ATX a su cabezal.
Español
(vea p.2, N. 5)
(vea p.2, N. 9)
ASRock 970 Extreme3 R2.0 Motherboard
73
A pesar de que esta placa base incluye in conector
de alimentación ATX de 24 pins, ésta puede funcionar
incluso si utiliza una fuente de alimentación ATX de
20 pins tradicional. Para usar una fuente de
alimentación ATX de 20 pins, por favor, conecte su
fuente de alimentación usando los Pins 1 y 13.
Instalación de una Fuente de Alimentación ATX de 20 Pins
Conector de ATX 12V power
(8-pin ATX12V1)
(vea p.2, N. 1)
5
1
8
4
12
24
1
13
Tenga en cuenta que es necesario conectar este conector a una toma de
corriente con el enchufe ATX 12V, de modo que proporcione suficiente electricidad. De lo contrario no se podrá encender.
Aunque esta placa base proporciona un conector de energía de 8-pin ATX 12V,
puede todavía trabajar si usted adopta un fuente tradicional de energía de 4-pin
ATX 12V. Para usar el fuente de energía de 4-pin ATX 12V, por favor conecte
5
1
su fuente de energía junto con Pin 1 y Pin 5.
Instalación de Fuente de Energía de 4-Pin ATX 12V
Cabezal del puerto COM
(9-pin COM1)
Español
74
8
4
(vea p.2, N. 30)
Este cabezal del puerto COM se utiliza para admitir un módulo de puerto COM.
Cabecera HDMI_SPDIF
(HDMI_SPDIF1 de 2 pin)
(vea p.2, N. 31)
Cabecera HDMI_SPDIF. Ofrece una salida SPDIF la tarjeta VGA HDMI, permite al sistema conectarse a dispositivos de TV Digital HDMI / proyectores / Dispositivos LCD. Conecte el conector HDMI_SPDIF de la tarjeta VGA HDMI a esta cabecera.
ASRock 970 Extreme3 R2.0 Motherboard
Cabezal USB 3.0
(19-pin USB3_2_3)
(vea p.2, N. 38)
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P2_SSTXIntA_P2_SSTX+
GND
IntA_P3_SSTXIntA_P3_SSTX+
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
Además de dos puertos 3.0
predeterminados situados en el
panel E/S, encontrará una
cabecera USB 3.0 en esta
placa base. Esta cabecera USB
3.0 admiten dos puertos USB
3.0.
2. BIOS Información
El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up
(POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna
tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la
BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> +
<Borrar>, o apretando el botón Reset en el panel del ordenador. Para información
detallada sobre como configurar la BIOS, por favor refiérase al Manual del Usuario
(archivo PDF) contenido en el CD.
3. Información de Software Support CD
Esta placa-base soporta diversos tipos de sistema operativo Windows®: 8 / 8 64 bits
Español
/ 7 / 7 64 bits / VistaTM / VistaTM 64 bits / XP / XP 64 bits. El CD de instalación que
acompaña la placa-base trae todos los drivers y programas utilitarios para instalar y
configurar la placa-base. Para iniciar la instalación, ponga el CD en el lector de CD
y se desplegará el Menú Principal automáticamente si «AUTORUN» está habilitado
en su computadora.
Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el archivo “ASSETUP.EXE” para iniciar la instalación.
ASRock 970 Extreme3 R2.0 Motherboard
75
1. Введение
Благодарим вас за покупку материнской платы ASRock 970 Extreme3 R2.0 надежной
материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock
жесткими требованиями к качеству. Она обеспечивает превосходную производительность
и отличается отличной конструкцией, которые отражают приверженность ASRock качеству
и долговечности.
Данное руководство по быстрой установке включает вводную информацию о материнской
плате и пошаговые инструкции по ее установке. Более подробные сведения о плате
можно найти в руководстве пользователя на компакт-диске поддержки.
Спецификации материнской платы и программное обеспечение BIOS иногда изменяются, поэтому содержание этого руководства может обновляться без уведомления. В случае любых модификаций руководства его новая версия будет размещена на веб-сайте ASRock без специального уведомления. Кроме того, самые свежие списки поддерживаемых модулей памяти и процессоров можно найти на сайте ASRock.
Адрес веб-сайта ASRock http://www.asrock.com
При необходимости технической поддержки по вопросам данной материнской платы посетите наш веб-сайт для получения информации об используемой модели.
www.asrock.com/support/index.asp
1.1 Комплектность
Материнская плата ASRock 970 Extreme3 R2.0 (форм-фактор ATX)
Руководство по быстрой установке ASRock 970 Extreme3 R2.0
Компакт-диск поддержки ASRock 970 Extreme3 R2.0
2 x кабель данных Serial ATA (SATA) (дополнительно)
1 x I/O Щит Группы ввода / вывода
ASRock напоминает...
Русский
Для обеспечения максимальной производительности ОС Windows®
8 / 8 64-bit / 7 / 7 64-bit / Vista TM / Vista TM 64-bit рекомендуется в
BIOS выбрать для параметра Storage Configuration (Конфигурация
запоминающего устройства) режим AHCI. Подробные сведения о
настройке BIOS см. в руководстве пользователя на прилагаемом
компакт-диске.
76
ASRock 970 Extreme3 R2.0 Motherboard
1.2 Спецификации
Платформа
- форм-фактор ATX
- Весь Твердый Конденсаторный проект (высококачественные конденсаторы с проводящим полимером; на 100% сделано в Японии)
Процессор
- Поддержка Socket AM3+ процессоров
- Поддержка Socket AM3 процессоров: AMD PhenomTM II X6 / X4 / X3 /
X2 (не поддерживаются 920 / 940) / Athlon II X4 / X3 / X2 / Sempron
- Поддержка восемьиядерных процессоров
- Поддержка UCC (Unlock CPU Core)
- Дизайн системы питания DigiPower
- Технология 4 + 1 Power Phase Design
- Поддержка процессоров мощностью до 140 Вт
- Поддержка технологии AMD Cool ‘n’ QuietTM
- FSB 2400 MHz (4.8 GT/s)
- Поддержка технологии Untied Overclocking
- Поддержка технологии Hyper-Transport 3.0 (HT 3.0)
Набор микросхем - Северный мост: AMD 970
- Южный мост: AMD SB950
Память
- Поддержка технологии Dual Channel DDR3 Memory Technology - 4 x гнезда DDR3 DIMM
- Поддержите DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/1333/
1066/800 не- ECC, безбуферная память
- Mакс. 32 Гб
Гнезда - 2 x слота PCI Express 2.0 x16
расширения
(PCIE2: режим x16; PCIE4: режим x4)
- 2 x гнезда PCI Express 2.0 x1
- 2 x гнезда PCI
- Поддерживает AMDTM Quad CrossFireXTM и CrossFireXTM
Аудиосистема
- 7.1 CH HD Аудио HD с Довольной Защитой
(Кодер-декодер Аудио Realtek ALC892)
- Поддержка Premium Blu-ray audio
ЛВС
- PCIE x 1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- поддержка Wake-On-LAN
- Поддержка определения кабеля ЛВС
- Поддержка энергосберегающего интерфейса Ethernet 802.3az
- Поддерживается PXE
Разъемы ввода- I/O Panel
вывода на задней - 1 x порт мыши PS/2
панели
- 1 x порт клавиатуры PS/2
- 1 x порт Coaxial SPDIF Out
- 1 x порт Optical SPDIF Out
- 4 x порта USB 2.0 на задней панели в стандартной конфигурации
ASRock 970 Extreme3 R2.0 Motherboard
Русский
77
SATA3
USB 3.0
Русский
Колодки и плате
BIOS
Компактдиск
поддержки Контроль
оборудо-
вания
78
- 2 x порта USB 3.0 на задней панели в стандартной конфигурации
- 1 x eSATA3 порт
- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор ACT/LINK и индикатор SPEED)
- Соединитель звуковой подсистемы: боковая колонка / тыльная колонка / центральная / субвуфер / линейный вход / передняя
колонка / микрофон
- 5 x портов SATA3 со скоростью передачи данных 6,0 Гбит/с,
поддержка функций RAID (RAID 0, RAID 1, RAID 5 и RAID 10), NCQ,
AHCI и «горячего подключения»
- 2 x задних порта USB 3.0 на контроллере Etron EJ188H с
поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи
данных до 5 Гбит/с
- 1 x передний разъем USB 3.0 (поддерживает 2 порта USB 3.0) на контроллере Etron EH188H с поддержкой интерфейсов
USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с
- 5 x разъема SATA3 6,0 Гбит/с
- 1 x Колодка инфракрасного модуля
- 1 x Датчик пользовательского инфракрасного модуля
- 1 x Колодка COM
- 1 x Колодка HDMI_SPDIF
- 1 x разъем Power LED
- 2 x соединитель CPU FAN (1 x 4-контактный, 1 x 3-контактный)
- 3 x соединитель Chassis FAN (1 x 4-контактный, 2 x 3-контактный)
- 1 x соединитель Power FAN (3-контактный)
- 24-контактный Колодка питания ATX
- 8-контактный Разъем ATX 12 В
- Аудиоразъем передней панели
- 3 x Колодка USB 2.0 (одна колодка для поддержки 6 дополнительных портов USB 2.0
- 1 x Колодка USB 3.0 (одна колодка для поддержки 2
дополнительных портов USB 3.0)
- 32Mb AMI UEFI Legal BIOS с поддержкой rpaфичеckoro интеpфeйca
поль зователя
- поддержка “Plug and Play”
- ACPI 1.1, включение по событиям
- поддержка режима настройки без перемычек
- поддержка SMBIOS 2.3.1
- Регулировка напряжений CPU, VCCM, NB, SB
- Драйверы, Утилиты, Антивирус (пробная версия), Пробная версия
программы CyberLink MediaEspresso 6.5, Google Chrome Browser и
Toolbar
- Датчики температуры процессора
- Датчики температуры корпуса
- Тахометры вентиляторов CPU/Chassis/Power FAN
ASRock 970 Extreme3 R2.0 Motherboard
- Бесшумный вентилятор ЦП/системного блока
- Мультиконтроль скорости вентилятора ЦП/Шасси
- Контроль напряжения: +12V, +5V, +3.3V, Vcore
Операцион
- Совместимость с Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit /
VistaTM / Поддержка 64-разрядной версии VistaTM / XP / XP 64-bit
ные
- FCC, CE, WHQL
системы - Совместимость с ErP/EuP Ready (требуется блок питания Сертификаты совместимый с ErP/EuP)
* Для детальной информации продукта, пожалуйста посетите наш вебсайт:
http://www.asrock.com
1.3 Установка перемычек
Конфигурация перемычек иллюстрируется
на рисунке. Когда перемычка надета на
контакты, они называются “замкнутыми”
(short). Если на контактах перемычки нет,
то они называются “разомкнутыми” (open).
На иллюстрации показана 3-контактная
перемычка, у которой контакты 1 и 2
замкнуты.
Перемычка
Установка
Описание
Очистка CMOS
(CLRCMOS1,
3-контактная перемычка)
(см. стр. 2, п. 21)
Стандартные
Очистка CMOS
ASRock 970 Extreme3 R2.0 Motherboard
Русский
Примечание.Контактная колодка CLRCMOS1 позволяет очистить данные CMOS. Для
очистки данных и восстановления заводских системных параметров сначала
выключите компьютер и отсоедините сетевую вилку кабеля питания от
электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5
секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не
производите очистку CMOS непосредственно после обновления BIOS. Если
необходимо очистить CMOS сразу же после окончания обновления BIOS, то,
перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а
затем завершить ее работу. Примите во внимание, что пароль, дата, время,
профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес
будут очищены только тогда, когда будет извлечена из своего гнезда батарейка
CMOS.
79
1.4 Колодки и разъемы на плате
Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ
контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки
на эти колодки и разъемы – это приведет к необратимому
повреждению материнской платы!
Разъемы Serial ATA3
Пять соединителя Serial ATA3
предназначаются для подключения внутренних устройств хранения с использованием нтерфейсных кабелей SATA3. В настоящее время интерфейс SATA допускает скорость передачи данных до \ 6,0 Гбит/с. Информационный кабель Serial ATA (SATA)
(дополнительно)
Информационный кабель интерфейса SATA / SATAII / SATA3 не является направленным. Любой из его соединителей может быть подключен либо к жесткому диску интерфейса SATA3 либо к
материнской плате.
Колодка USB 2.0
Помимо четыре стандартных портов USB 2.0 на панели ввода-
вывода, на данной материнской плате предусмотрено три разъема USB 2.0. Каждый разъем USB 2.0 поддерживает два порта USB 2.0.
(SATA3_1, см. стр. 2, п. 17) (SATA3_2, см. стр. 2, п. 18) SATA3_3
SATA3_1
SATA3_4
SATA3_2
(SATA3_3, см. стр. 2, п. 16) (SATA3_4, см. стр. 2, п. 19) (SATA3_5, см. стр. 2, п. 20) SATA3_5
(9-контактный USB_4_5)
(см. стр. 2, п. 26)
(9-контактный USB_6_7)
(см. стр. 2, п. 27)
Русский
USB_PWR
P-9
P+9
GND
DUMMY
(9-контактный USB_8_9)
(см. стр. 2, п. 28)
1
GND
P+8
P-8
USB_PWR
80
ASRock 970 Extreme3 R2.0 Motherboard
Колодка инфракрасного модуля
(5-контактный IR1)
(см. стр. 2, п. 29)
Данная колодка позволяет подключить дополнительный модуль беспроводного инфракрасного приемопередатчика.
Датчик пользовательского инфракрасного модуля
(4-контактный CIR1)
(см. стр. 2, п. 25)
Датчик можно использовать для
подключения дистанционный приемник.
Аудиоразъем передней панели
(9-контактный HD_AUDIO1)
(см. cтр. 2, п. 32)
Этот интерфейс предназначен
для присоединения аудиокабеля передней панели,
обеспечивающего удобное подключение аудиоустройств и управление ими.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. Система High Definition Audio поддерживает функцию автоматического обнаружения разъемов (Jack Sensing), однако
для ее правильной pаботы кабель панели в корпусе должен поддерживать HDA. При сборке системы следуйте инструкциям,
приведенным в нашем руководстве и руководстве пользователя для корпуса.
2. Если вы используете аудиопанель AC’97, подключите ее к колодке
аудиоинтерфейса передней панели следующим образом:
A. Подключите выводы Mic_IN (MIC) к контактам MIC2_L.
B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а выводы Audio_L (LIN) к контактам OUT2_L.
C. Подключите выводы Ground (GND) к контактам Ground (GND).
D. Контакты MIC_RET и OUT_RET предназначены только для аудиопанели HD. При использовании аудиопанели AC’97 подключать их не нужно.
E. Процедура активации микрофона приведена ниже.
Для ОС Windows® XP / XP 64-бита:
Выберите «Mixer» (Микшер). Выберите «Recorder» (Устройство записи). Затем щелкните «FrontMic» (Передний микрофон).
Для ОС Windows® 8 / 8 64-бита / 7 / 7 64-бита / VistaTM / VistaTM
64-бита:
Перейдите к вкладке «FrontMic» (Передний микрофон) в панели
управления Realtek. Отрегулируйте уровень «Recording
Volume» (Громкость записи).
Колодка системной панели
(9-контактный PANEL1)
(см. стр. 2, п. 23)
Русский
GND
PRESENCE#
MIC_RET
OUT_RET
Данная колодка обеспечивает работу нескольких функций передней панели системы.
ASRock 970 Extreme3 R2.0 Motherboard
81
Подключите к этому разъему кнопку питания, кнопку сброса и индикатор состояния системы на корпусе в соответствии с указанным ниже назначением контактов. При подключении кабелей необходимо соблюдать полярность положительных и отрицательных
контактов.
PWRBTN (кнопка питания):
Подключите к этим контактам кнопку питания на передней панели корпуса. Способ выключения системы с помощью кнопки питания можно настроить.
RESET (кнопка сброса):
Подключите к этим контактам кнопку сброса на передней панели корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если компьютер «завис» и нормальную перезагрузку выполнить не удается.
PLED (индикатор питания системы):
Подключите к этим контактам индикатор состояния питания на
передней панели корпуса. Этот индикатор светится, когда система работает. Индикатор мигает, когда система находится в режиме
ожидания S1. Этот индикатор не светится, когда система находится в режиме ожидания S3 или S4, либо выключена (S5).
HDLED (индикатор активности жесткого диска):
Подключите к этим контактам индикатор активности жесткого диска на передней панели корпуса. Этот индикатор светится, когда осуществляется считывание или запись данных на жестком диске.
Конструкция передней панели может различаться в зависимости от корпуса. Модуль передней панели в основном состоит из кнопки
питания, кнопки сброса, индикатора питания, индикатора активности
жесткого диска, динамика и т.п. При подключении к этому разъему модуля передней панели корпуса удостоверьтесь, что провода подключаются к соответствующим контактам.
Русский
82
Колодка динамика корпуса
(4-контактный SPEAKER1)
(см. стр. 2, п. 24)
Подключите к этой колодке кабель от динамика на корпусе компьютера.
разъем Power LED (3-контактный PLED1)
(см. стр. 2, п. 22)
Подключите индикатор Power LED к этому разъему для отображения статуса питания системы. Этот светодиод продолжит мигать в режиме S1. Светодиод будет
выключен в режимах S3/S4 или S5 (система выключена).
ASRock 970 Extreme3 R2.0 Motherboard
Chassis и Power Fan-соединители
(4-контактный CHA_FAN1)
Подключите кабели вентилятора
к соединителям и присоедините
(см. стр. 2, п. 12)
черный шнур к штырю
заземления. Управление
скоростью вентиляторов CHA_
FAN1/2/3 может осуществляться
посредством UEFI или AXTU.
(3-контактный CHA_FAN2)
GND
+12V
CHA_FAN_SPEED
(см. стр. 2, п. 15)
(3-контактный CHA_FAN3)
(см. стр. 2, п. 2)
(3-контактный PWR_FAN1)
(см. стр. 2, п. 10)
Разъем вентилятора процессора
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
(4-контактный CPU_FAN1)
(см. стр. 2, п. 6)
Подключите к этому разъему кабель вентилятора процессора так, чтобы черный провод соответствовал контакту земли.
1 2 3 4
Данная материнская плата поддерживает вентиляторы процессора
с 4-контактным разъемом (функция тихого режима вентилятора),
однако вентиляторы с 3-контактным разъемом также будут успешно
работать, хотя функция управления скоростью вращения
вентилятора окажется недоступной. Если вы хотите подключить
вентилятор процессора с 3-контактным разъемом к разъему
вентилятора процессора на данной материнской плате, для этого
следует использовать контакты 1-3.
Контакты 1-3 подключены
Установка вентилятора с 3-контактным разъемом
(3-контактный CPU_FAN2)
GND
+12V
CPU_FAN_SPEED
(см. стр. 2, п. 5)
Колодка питания ATX
(24-контактный ATXPWR1) 12
24
1
13
Подключите к этой колодке кабель питания ATX.
ASRock 970 Extreme3 R2.0 Motherboard
Русский
(см. стр. 2, п. 9)
83
Несмотря на то, что эта материнская плата предусматр- 12
ивает 24-штыревой разъем питания ATX, работа будет
продолжаться, даже если адаптируется традиционный
20-штыревой разъем питания ATX. Для использования
20-штыревого разъема питания ATX вставьте источник
питания вместе со штекером 1 и штекером 13.
24
Установка 20-штыревого разъема питания ATX 1
Колодка питания 12V-ATX
(8-контактный ATX12V1) (см. стр. 2, п. 1)
5
1
8
4
Обратите внимание, что к этому разъему необходимо подключить вилку блока питания ATX 12 В, чтобы обеспечить достаточную мощность электропитания. В противном случае включение системы будет невозможно.
Хотя эта объединительная плата обеспечивает ATX с 8 булавками 12V соединитель власти, это может все еще работать, если Вы принимаете традиционный ATX с 4-Pin 12V электропитание. Чтобы использовать электропитание ATX с 4-Pin, пожалуйста включите ваше электропитание наряду с Булавкой 1 и Прикрепите 5.
5
1
ATX С 4-Pin 12V Установка Электропитания
8
4
Колодка COM-порта
(9-контактный COM1) (см. стр. 2, п. 30)
Данная колодка COM-порта позволяет подключить модуль порта COM.
Колодка HDMI_SPDIF
Колодка HDMI_SPDIF обеспечивает подачу выходного
аудиосигнала на VGA-карту HDMI, что позволяет подключать к системе цифровые телевизоры,
проекторы или
жидкокристаллические панели HDMI. Соедините эту колодку с
разъемом HDMI_SPDIF на VGA-
карте HDMI.
(2-контактный HDMI_SPDIF1)
(см. стр. 2, п. 31)
Русский
84
13
ASRock 970 Extreme3 R2.0 Motherboard
Колодка USB 3.0
(19-контактный USB3_2_3)
Vbus
Vbus
IntA_P3_SSRX-
(см. стр. 2, п. 38)
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
Помимо два стандартных
портов USB 3.0 на панели вводавывода, на данной материнской
плате предусмотрен один разъем
USB 3.0. Этот разъем USB 3.0
поддерживает два порта USB 3.0.
2. Информация о BIOS
Утилита настройки BIOS (BIOS Setup) хранится во флэш-памяти на материнской плате.
Чтобы войти в программу настройки BIOS Setup, при запуске компьютера нажмите <F2>
или <Del> во время самопроверки при включении питания (Power-On-Self-Test – POST).
Если этого не сделать, то процедуры тестирования POST будут продолжаться обычным
образом. Если вы захотите вызвать BIOS Setup уже после POST, перезапустите систему
с помощью клавиш <Ctrl> + <Alt> + <Delete> или нажатия кнопки сброса на корпусе
системы. Подробную информацию о программе BIOS Setup вы найдете в Руководстве
пользователя (в формате PDF) на компакт-диске поддержки.
3. Информация о компакт-диске поддержки с программным обеспечением
®
Русский
Данная материнская плата поддерживает различные операционные системы Microsoft
®
Windows : 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Поставляемый
вместе с ней компакт-диск поддержки содержит необходимые драйверы и полезные
утилиты, которые расширяют возможности материнской платы.
Чтобы начать работу с компакт-диском поддержки, вставьте его в дисковод CD-ROM.
Если в вашем компьютере включена функция автозапуска (AUTORUN), то на экране
автоматически появится главное меню компакт-диска (Main Menu). Если этого не
произошло, найдите в папке BIN на компакт-диске поддержки файл ASSETUP.EXE и
дважды щелкните на нем, чтобы открыть меню.
ASRock 970 Extreme3 R2.0 Motherboard
85
1. Introdução
Gratos por comprar nossa placa–mãe 970 Extreme3 R2.0 um produto confiável
feito com ASRock um estrito controle de qualidade consistente. Com um excelente
desempenho, essa placa é dotada de um projeto robusto que atende a ASRock de
compromisso com a qualidade e durabilidade.
Este Guia de Instalação Rápida apresenta a placa-mãe e o guia de instalação passo a passo. Mais informações detalhadas sobre a placa-mãe podem ser encontradas no manual do usuário do CD de suporte.
Porque as especificações da placa mãe e o software de BIOS poderiam
ser atualizados, o conteúdo deste manual pode ser cambiado sem aviso.
Em caso de qualquer modificação deste manual, a versão atualizada
estará disponível no website de ASRock sem prévio aviso. Pode também
encontrar as listas das mais recentes placas VGA e das CPUs suportadas
no site da web da ASRock.
Website de ASRock http://www.asrock.com
Se precisar de apoio técnico em relação a este placa-mãe, por favor visite
o nosso sítio da internet para informação específica acerca do modelo que
está a utilizar.
www.asrock.com/support/index.asp
1.1 Este pacote contém
Placa-mãe ASRock 970 Extreme3 R2.0 (Formato ATX)
Guia de instalação rápida da ASRock 970 Extreme3 R2.0
CD de suporte da placa ASRock 970 Extreme3 R2.0
Dois cabo de dados ATA Serial (SATA) (Opcional)
Uma proteção I/O
A ASRock recorda-lhe...
Português
Para obter melhor desempenho em Windows® 8 / 8 64-bit / 7 / 7 64-bit /
VistaTM / VistaTM 64-bit, recomendamos que defina a opção Configuração
de Armazenamento na BIOS para o modo AHCI. Para mais detalhes
acerca da configuração da BIOS consulte o “Manual de utilizador” no
nosso CD de suporte.
86
ASRock 970 Extreme3 R2.0 Motherboard
1.2 Especificações
- Formato ATX
- Design de condensadores banhados a ouro de alta qualidade
(Condensadores de polímeros condutores de alta qualidade
100% fabricados no Japão)
- Suporte para processadores AM3+
- Suporte para processadores AM3: Processador AMD
PhenomTM II X6 / X4 / X3 / X2 (exceto 920 / 940) / Athlon II X4
/ X3 / X2 / Sempron
- Preparado para CPU de oito núcleos
- Suporta UCC (Unlock CPU Core)
- Design de Poder Digital
- Alimentação de 4 + 1 fases
- Suporta CPU até 140W
- Suporta a tecnologia Cool ‘n’ Quiet da AMD
- FSB de 2400 MHz (4,8 GT/s)
- Suporta a tecnologia Untied Overclocking
- Suporta a tecnologia Hyper-Transport 3.0 (HT 3.0)
- North Bridge: AMD 970
- South Bridge: AMD SB950
- Suporte à tecnologia de memória de duplo canal
- 4 x slots de DDR3 DIMM
- Suporta memória DDR3 2100+(OC)/1866(OC)/1800(OC)/
/1600(OC)/1333/1066/800, não ECC, sem tampão
- Capacidade máxima de memória do sistema: 32GB
- 2 x slots de PCI Express 2.0 x16
(PCIE2: modo x16; PCIE4: modo x4) - 2 x slots de PCI Express 2.0 x1
- 2 x slots de PCI
- Suporta Quad CrossFireXTM e CrossFireXTM da AMD
- Áudio HD de 7.1 canais com protecção de conteúdo
(Realtek ALC892 Audio Codec)
- Suporte áudio Blu-ray superior
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Suporta Wake-On-LAN
- Suporta Detecção de cabo LAN
- Suporta Ethernet com Eficiência Energética 802.3az
- Suporta PXE
ASRock 970 Extreme3 R2.0 Motherboard
Português
Plataforma
CPU
Chipsets
Memória
Slots de Expansão
Áudio
LAN
87
Português
Entrada/SaídaI/O Panel
pelo painel
- 1 x porta para mouse PS/2
- 1 x porta para teclado PS/2
- 1 x porta Saída SPDIF (coaxial)
- 1 x porta Saída SPDIF (optical)
- 4 x portas USB 2.0 padrão
- 2 x portas USB 3.0 padrão
- 1 x Conector eSATA3
- 1 x porta LAN RJ-45 com LED (LED ACT/LIG e LED
VELOCIDADE)
- Ficha de áudio HD: Altifalante lateral/Altifalante traseiro/
Central/Baixos/Entrada de linha/Altifalante frontal/Microfone
SATA3
- 5 x conectores SATA3 a 6,0 Gb/s, com suporte para RAID
(RAID 0, RAID 1, RAID 5 e RAID 10), NCQ, AHCI e funções
Hot Plug
USB3.0
- 2 x Portas USB 3.0 traseiras através de EJ188H da
Etron, com suporte para USB 1.1/2.0/3.0 até 5Gb/s
- 1 x Conector USB 3.0 frontal (suporta 2 portas USB 3.0) através de EJ188H da Etron, com suporte para USB 1.1/2.0/3.0
até 5Gb/s
Conectores
- 5 x conectores SATA3, suporte a taxa de transferência de
dados de até 6,0 Gb/s
- 1 x Conector do módulo de infravermelho
- 1 x Conector CIR
- 1 x conector de porta COM
- 1 x Conector HDMI_SPDIF
- 1 x Conector para LED de alimentação
- 2 x Conector do ventilador da CPU (1 x 4 pinos, 1 x 3 pinos) - 3 x Conector do ventilador da chassis
(1 x 4 pinos, 2 x 3 pinos) - 1 x Conector do ventilador da energia (3 pinos)
- Conector de força do ATX de 24 pinos
- Conector ATX 12 V de 8 pinos
- Conector Áudio do painel frontal
- 3 x cabezal USB 2.0 (suporta 6 portas USB 2.0)
- 1 x cabezal USB 3.0 (suporta 2 portas USB 3.0)
BIOS
- 32Mb BIOS UEFI oficial da AMI com suporte para GUI
- Suporta dispositivos “Plug and Play”
- ACPI 1.1 atendendo a eventos de “wake up”
- Suporta dispositivos sem jumper
- Suporte para SMBIOS 2.3.1
88
ASRock 970 Extreme3 R2.0 Motherboard
CD de suporte
Monitor do HW
Sistema Operacional
Certificações
- CPU, VCCM, NB, SB Voltage Multi-adjustment
- Controladores, utilitários, software antivírus (Experimentacao
Versao), CyberLink MediaEspresso 6.5 versão de
demonstração, Navegador Google Chrome e Barra de
Ferramentas
- Sensores de temperature do procesador
- Medição de temperatura da placa-mãe
- Tacômetros de ventilador do Processador/chassis/energia
- Ventoinha silenciosa para a CPU/chassis
- CPU/chassis Fan Controle Multi-Velocidade
- Monitoramento de voltagem : +12 V, +5 V, +3.3 V, Vcore
- Microsoft® Windows® 8 / 8 de 64 bits / 7 / 7 de 64 bits / VistaTM
/ VistaTM de 64 bits / XP / XP de 64 bits
- FCC, CE, WHQL
- “ErP/EuP Ready” (é necessária alimentação eléctrica “ErP/
EuP Ready”)
Português
* Para informações mais detalhadas por favor visite o nosso sítio Web: http://www.asrock.com
ASRock 970 Extreme3 R2.0 Motherboard
89
1.3 Configuração dos Jumpers
A ilustração mostra como os jumpers são
configurados. Quando há uma capa de
jumpers sobre os pinos, diz–se que o jumper está “curto”. Não havendo capa sobre os
pinos, o jumper está “aberto”. A ilustração
mostra um jumper de 3 pinos em que os
pinos 1 e 2 están “curtos” quando a capa
de jumper estiver colocada sobre esses 2
pinos.
Jumper
Configuração
Restaurar CMOS
(CLRCMOS1, jumper de 3 pinos)
(veja a folha 2, No. 21)
Configuração-padrão
Limpar o CMOS
Nota: CLRCMOS1 permite você limpar os dados em CMOS. Os dados em CMOS
incluem informações da configuração do sistema como: por exemplo a senha
do sistema, data, tempo, e os parámetros da configuração do sistema. Para
limpar e reconfigurar os parámetros do sistema a configuração inicial da fábrica, por favor desligue o cabo de força, ponha em curto–circuito os pin 2 e
pin 3 de CLRCMOS1 por mais de 5 segundos para limpar o CMOS usando
um jumper. Por favor lembrese de remover o jumper depois de limpar o
COMS. Se precisar limpar o CMOS ao concluir a atualização do BIOS, deverá reiniciar o sistema primeiro e, em seguida, desligá-lo antes de executar
a ação de limpeza o CMOS. Tenha em atenção que a palavra-passe, data,
hora, perfil predefinido de utilizador, 1394 GUID e endereço MAC apenas
serão limpos se a bateria do CMOS for retirada.
Português
90
ASRock 970 Extreme3 R2.0 Motherboard
1.4 Conectores
Os conectores NÃO SÃO jumpers. NÃO coloque capas de jumper
sobre estes conectores. A colocação de pontos de jumper sobre os
conectores causará danos irreversíveis à placa-mãe.
Conectores ATA3 Serial
(SATA3_1: veja a folha 2, No. 17) (SATA3_2: veja a folha 2, No. 18) SATA3_5
(SATA3_3: veja a folha 2, No. 16)
(SATA3_4: SATA3_3
SATA3_1
SATA3_4
SATA3_2
Estes cinco conectores Serial
ATA (SATA3) suportam unidades de disco rígido SATA
ou SATA3 como dispositivos de
armazenamento internos. A
atual interface SATA3 permite
uma taxa de transferência de
dados de até 6.0 Gb/s.
veja a folha 2, No. 19)
(SATA3_5:
veja a folha 2, No. 20)
Cabo de dados
ATA (SATA)
(opcional)
Tanto a saída do cabo de Serial
dados SATA pode ser
conectado ao disco rígido
SATA / SATA2 / SATA3 quanto
o conector SATA3 na placa
mãe.
Cabezal USB 2.0
(USB_4_5 de 9 pinos)
(veja a folha 2, No. 26)
Além das quatro portas USB 2.0
por defeito no painel de
entrada/saída, há três ligações
USB 2.0 nesta placa-mãe.
Cada ligação USB 2.0 pode
suportar dois portas USB 2.0.
(USB_8_9 de 9 pinos)
Português
(USB_6_7 de 9 pinos)
(veja a folha 2, No. 27)
USB_PWR
P-9
P+9
GND
DUMMY
(veja a folha 2, No. 28)
1
GND
P+8
P-8
USB_PWR
ASRock 970 Extreme3 R2.0 Motherboard
91
Conector do módulo
de infravermelho
(IR1 de 5 pinos)
(veja a folha 2, No. 29)
Este conector suporta um
módulo de infravermelho para
transmissão e recepção sem
fio, opcional.
Conector do módulo de infravermelhos
(CIR1 de 4 pinos)
Este conector pode ser utilizado
para ligar o receptor do controlo
remoto.
(veja a folha 2, No. 25)
Conector Áudio do painel frontal
(HD_AUDIO1 de 9 pinos)
(veja a folha 2, No. 32)
Português
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
Esta é uma interface para o
cabo de áudio no painel frontal,
que permite uma conexão e
controle convenientes dos
dispositivos de áudio.
1. Áudio de elevada definição que suporta a sensibilidade da tomada,
mas o fio do painel existente no chassis tem de suportar HDA para
funcionar correctamente. Siga s instruções que aparecem no manual
e no manual do chassis para instalar o sistema.
2. Se utilizar o painel de áudio AC’97, instale-o no cabeçalho de áudio
do painel frontal, como a figura abaixo mostra:
A. Ligue o Mic_IN (MIC) ao MIC2_L.
B. Ligue o Audio_R (RIN) ao OUT2_R e o Audio_L (LIN) ao OUT2_L.
C. Ligue o Ground (GND) ao Ground (GND).
D. MIC_RET e OUT_RET são apenas para o painel de áudio HD. Não
necessita de os ligar para o painel de áudio AC’97.
E. Para activar o microfone frontal.
Para os Sistemas Operativos Windows® XP / XP 64 bits:
Seleccione “Misturador”. Seleccione “Gravador”. Depois clique
em “Microfone frontal”.
Para os Sistemas Operativos Windows® 8 / 8 64-bit / 7 / 7 64-bit /
VistaTM / VistaTM 64-bit:
Aceda ao separador “Microfone frontal” no painel de Controlo
Realtek. Ajuste o “Volume de gravação”.
Conector do painel do sistema
(PANEL1 de 9 pinos)
(veja a folha 2, No. 23)
92
GND
PRESENCE#
MIC_RET
OUT_RET
Este conector acomoda várias
funções do painel frontal do
sistema.
ASRock 970 Extreme3 R2.0 Motherboard
Ligue o botão de alimentação, o botão de reposição e o indicador do
estado do sistema no chassis a este conector de acordo com a descrição
abaixo. Tenha em atenção os pinos positivos e negativos antes de ligar os
cabos.
PWRBTN (Botão de alimentação):
Ligue ao botão de alimentação no painel frontal do chassis. Pode configurar a forma para desligar o seu sistema através do botão de alimentação.
RESET (Botão de reposição):
Ligue ao botão de reposição no painel frontal do chassis. Prima o botão
de reposição para reiniciar o computador caso este bloqueie e não seja
possível reiniciar normalmente.
PLED (LED de alimentação do sistema):
Ligue ao indicador do estado da alimentação no painel frontal do chassis.
O LED ficará acesso quando o sistema estiver em funcionamento. O LED
ficará intermitente quando o sistema estiver no estado de suspensão S1.
O LED ficará desligado quando o sistema estiver nos estados de suspensão S3/S4 ou desligado (S5).
HDLED (LED de actividade do disco rígido):
Ligue ao LED de actividade do disco rígido no painel frontal do chassis. O
LED ficará acesso quando o disco rígido estiver a ler ou a escrever dados.
O design do painel frontal poderá variar dependendo do chassis. Um
módulo de painel frontal consiste principalmente em um botão de alimentação, um botão de reposição, um LED de alimentação, um LED de actividade do disco rígido, um altifalante, etc. Ao ligar o seu módulo de painel
frontal do chassis a este conector, certifique-se que os fios e os pinos têm
uma correspondência exacta.
Conector do alto-falante do chassi
Ligue o alto-falante do chassi neste conector.
(SPEAKER1 de 4 pinos)
(veja a folha 2, No. 24)
Ligue o LED de alimentação do
chassis a este conector para
indicar o estado de alimentação
do sistema. O LED ficará
acesso quando o sistema
estiver em funcionamento. O
LED fica intermitente no estado
S1. O LED fica desligado
nos estados S3/S4 ou no
estado S5 (desligado).
ASRock 970 Extreme3 R2.0 Motherboard
Português
Conector do LED de alimentação
(PLED1 de 3 pinos)
(veja a folha 2, No. 22)
93
Conector do ventilador do chassis/energia
(CHA_FAN1 de 4 pinos)
Ligue o cabo do ventilador
neste conector, coincidindo o fio
(veja a folha 2, No. 12)
preto com o pino de aterramen
to. CHA_FAN1/2/3 suportam a
função de Controlo de
Ventoinha através AXTU
ou UEFI.
(CHA_FAN2 de 3 pinos)
GND
+12V
CHA_FAN_SPEED
(veja a folha 2, No. 15)
(CHA_FAN3 de 3 pinos)
(veja a folha 2, No. 2)
(PWR_FAN1 de 3 pinos)
(veja a folha 2, No. 10)
Conector do ventilador da CPU
(CPU_FAN1 de 4 pinos)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
Ligue o cabo do ventilador da
CPU, coincidindo o fio preto
com o pino de aterramento.
(veja a folha 2, No. 6)
1 2 3 4
Apesar de esta placa-mãe possuir 4 apoios para uma ventoinha de CPU
(Ventoinha silenciosa), uma ventoinha de 3 pinos para CPU poderá funcionar
mesmo sem a função de controlo de velocidade da ventoinha. Se pretender ligar
uma ventoinha de 3 pinos para CPU ao conector de ventoinha do CPU nesta
placa-mãe, por favor, ligue-a aos pinos 1-3.
Pinos 1-3 ligados
Instalação de Ventoinha de 3 pinos
(CPU_FAN2 de 3 pinos)
(veja a folha 2, No. 5)
GND
+12V
CPU_FAN_SPEED
Conector de força do ATX (ATXPWR1 de 24 pinos)
12
24
1
13
Ligue a fonte de alimentação
ATX neste conector.
(veja a folha 2, No. 9)
Português
Embora esta placa-mãe providencie um conector de
energia ATX de 24 pinos, pode apesar disso funcionar
com a adapta-ção de uma fonte de energia tradicional
de 20 pinos. Para usar a fonte de alimentação de 20
pinos, por favor ligue a sua fonte de alimentação com
o Pino 1 e o Pino 13.
Instalação da Fonte de alimentação ATX de 20 Pinos
94
ASRock 970 Extreme3 R2.0 Motherboard
12
24
1
13
Conector de força do ATX 12V (ATX12V1 de 8 pinos)
5
1
(veja a folha 2, No. 1)
8
4
Ligue a fonte de alimentação
ATX 12V neste conector.
Embora esta placa-mãe providencie um conector de energia ATX 12V
de 8 pinos, pode apesar disso funcionar com a adapta-ção de uma
fonte de energia tradicional de 4 pinos. Para usar a fonte de
alimentação de 4 pinos, por favor ligue a sua fonte de alimentação com
5
1
o Pino 1 e o Pino 5.
Instalação da Fonte de alimentação ATX 12V de 4 Pinos
Conector de porta de série (COM1 de 9 pinos)
8
4
Este conector COM1 suporta
um módulo de porta de série.
(veja a folha 2, No. 30)
Conector HDMI_SPDIF
(HDMI_SPDIF1 de 2 pinos)
(veja a folha 2, No. 31)
O conector HDMI_SPDIF, que
oferece saída de áudio SPDIF
para placas VGA HDMI, permite
ligar televisores digitais/
projectores/LCD com entrada
HDMI ao sistema. Ligue o
conector HDMI_SPDIF da placa
VGA HDMI a este conector.
(USB3_2_3 de 19 pinos)
(veja a folha 2, No. 38)
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P2_SSTXIntA_P2_SSTX+
GND
IntA_P3_SSTXIntA_P3_SSTX+
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
Além das dois portas USB 3.0
por defeito no painel de
entrada/saída, há uns ligações
USB 3.0 nesta placa-mãe.
Cada ligação USB 3.0 pode
suportar dois portas USB 3.0.
ASRock 970 Extreme3 R2.0 Motherboard
Português
Cabezal USB 3.0
95
2. Informações da BIOS
O Utilitário de Configuração do BIOS está armazenado no chip FWH do BIOS. Ao
iniciar o computador, pressione <F2> ou <Del> durante o Autoteste de iniciação
(POST) para acessar o Utilitário de Configuração do BIOS; caso contrário, o POST
continuará com as rotinas de teste. Se desejar acessar o Utilitário de Configuração
do BIOS depois do POST, reinicie o sistema pressionando <Ctl> + <Alt> + <Del>,
ou pressionando o botão de reinício no chassi do sistema. Para as informações detalhadas sobre o Utilitário de Configuração do BIOS, consulte o Manual do Usuário
(arquivo PDF) no CD de suporte.
3. Informações do CD de Suporte
Esta placa Mãe suporta vários sistemas operacionais: Microsoft® Windows®: 8 / 8
de 64 bits / 7 / 7 de 64 bits / VistaTM / VistaTM de 64 bits / XP / XP de 64 bits. O CD
de instalação que acompanha a placa Mãe contem: drivers e utilitários necessários
para um melhor desempenho da placa Mãe. Para começar a usar o CD de instalação, introduza o CD na leitora de CD-ROM do computador. Automaticamente
iniciará o menu principal, casa o AUTORUN esteja ativado. Se o menu principal não
aparecer automaticamente, explore o CD e execute o “ASSETUP.EXE” localizado
na pasta BIN.
Português
96
ASRock 970 Extreme3 R2.0 Motherboard
1. Giriş
ASRock’ın kesintisiz titiz kalite denetimi altında üretilen güvenilir bir anakart olan ASRock 970 Extreme3 R2.0 anakartını satın aldığınız için teşekkür ederiz. ASRock’ın
kalite ve dayanıklılık konusundaki kararlılığına uygun güçlü tasarımıyla mükemmel
bir performans sunar.
Bu Hızlı Takma Kılavuzu anakarta giriş ve adım adım takma kılavuzu içerir. Anakart
hakkında daha ayrıntılı bilgiyi Destek CD’sinde sunulan kullanıcı kılavuzunda bulabilirsiniz.
Anakart özellikleri ve BIOS yazılımı güncelleştirilebileceğinden bu kılavuzun içeriği
önceden haber verilmeksizin değişebilir. Bu belgede değişiklik yapılması durumun
-da, güncelleştirilmiş sürüm ayrıca haber verilmeksizin ASRock web sitesinde sunulur. En son VGA kartlarını ve CPU destek listelerini de ASRock web sitesinde bulabilirsiniz. ASRock web sitesi http://www.asrock.com
Bu anakartla ilgili teknik desteğe ihtiyacınız olursa, kullandığınız modele özel bilgiler için lütfen web sitemizi ziyaret edin.
www.asrock.com/support/index.asp
1.1 Paket İçindekiler
ASRock 970 Extreme3 R2.0 Anakart (ATX Form Faktörü)
ASRock 970 Extreme3 R2.0 Hızlı Takma Kılavuzu
ASRock 970 Extreme3 R2.0 Destek CD’si
2 x Seri ATA (SATA) Veri Kablosu (İsteğe Bağlı)
1 x G/Ç Panel Kalkanı
ASRock Size Şunu Hatırlatır...
Türkçe
Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit ile daha iyi
performans elde etmek için, Depolama Konfigürasyonundaki BIOS
seçeneğini AHCI moduna ayarlamanız tavsiye edilir. BIOS ayarı
için, ayrıntıları öğrenmek üzere lütfen destek CD'mizdeki "Kullanıcı
Kılavuzu"na bakın.
ASRock 970 Extreme3 R2.0 Motherboard
97
1.2 Özellikler
Türkçe
Platform
CPU
Yonga seti
Bellek
Genişletme Yuvası Ses
LAN
98
- ATX Form Faktörü
- Tüm Katı Kapasitör tasarımı (%100 Japon yapımı yüksek
kaliteli Polimer Kapasitörler)
- Soket AM3+ işlemcileri desteği
- Soket AM3 işlemcileri desteği: AMD PhenomTM II X6 / X4 / X3 /
X2 (920 / 940 hariç) / Athlon II X4 / X3 / X2 / Sempron
işlemcileri
- Sekiz Çekirdekli CPU Desteği
- UCC özelliğini destekler - CPU çekirdeği Kilidi Açma
- Digi Güç Tasarımı
- 4 + 1 Güç Fazı Tasarımı
- 140W’ye kadar CPU’yu destekler
- AMD’nin Cool ‘n’ QuietTM Teknolojisini Destekler
- FSB 2400 MHz (4,8 GT/sn)
- Untied Overclocking Teknolojisini destekler
- Hyper-Transport 3.0 (HT 3.0) Teknolojisini Destekler
- Kuzey Köprüsü: AMD 970
- Güney Köprüsü: AMD SB950
- Çift Kanallı DDR3 Belleği Teknolojisi
- 4 x DDR3 DIMM yuva
- DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/1333/1066/
800 ECC olmayan, ara belleksiz bellek
- Sistem belleğinin maks. kapasitesi: 32 GB
- 2 x PCI Express 2.0 x16 yuva
(PCIE2: x16 modu; PCIE4: x4 modu)
- 2 x PCI Express 2.0 x1 yuva
- 2 x PCI yuva
- AMDTM CrossFireXTM ve Quad CrossFireXTM ‘i destekler
- İçerik Korumalı (Realtek ALC892 Ses Kodeki) 7,1 Kanal HD
Ses
- Premium Blu-ray ses desteği
- PCIE x1 Gigabit LAN 10/100/1000 Mb/sn
- Realtek RTL8111E
- LAN’da Uyan özelliğini destekler
- LAN Kablo Algılama’yı destekler
- Enerji Verimli Ethernet 802.3az desteği
- PXE destekler
ASRock 970 Extreme3 R2.0 Motherboard
G/З Paneli
- 1 x PS/2 Fare Portu
- 1 x PS/2 Klavye Portu
- 1 x 1 x Koaksiyel SPDIF Çıkışı Portu
- 1 x Optik SPDIF Çıkışı Portu
- 4 x Kullanıma Hazır USB 2.0 Portu
- 2 x Kullanıma Hazır USB 3.0 Portu
- 1 x eSATA3 Konektörü
- 1 x RJ-45 LAN Portu, LED’li (AKT/LЭNK LED’i ve HIZ LED)
- HD Ses Jakı: Yan Hoparlör/Arka Hoparlör/Orta/Bas/Hat Girişi/
Ön Hoparlör/Mikrofon
- 5 x SATA3 6,0Gb/sn konektör, donanım RAID (RAID 0, RAID 1,
RAID 5 ve RAID 10), NCQ, AHCI ve “Sistem Aзэkken Bileюen
Takma” işlevlerini
- Etron EJ188H tarafından 2 x Arka USB 3.0 bağlantı noktası,
5Gb/s’ye kadar USB 1.1/2.0/3.0
- Etron EJ188H tarafından 1 x Ön USB 3.0 bağlantısı (2 USB 3.0
bağlantı noktasını destekler), 5Gb/s’ye kadar USB 1.1/2.0/3.0
- 5 x SATA3 6,0 Gb/s konektör
- 1 x KÖ fişi
- 1 x Kullanıcı Kızılötesi Modül Bağlantısı
- 1 x COM portu fişi
- 1 x HDMI_SPDIF fişi
- 1 x Güç LED’i fişi
- 2 x CPU FAN konektörü (1 x 4 pin, 1 x 3 pin)
- 3 x Kasa FAN konektörü (1 x 4 pin, 2 x 3 pin)
- 1 x Gьз FAN konektörü (3 pin)
- 24 pin ATX güç konektörü
- 8 pin 12V güç konektörü
- Ön panel ses konektörü
- 3 x USB 2.0 fiş (6 USB 2.0 portu destekler)
- 1 x USB 3.0 fiş (2 USB 3.0 portu destekler)
- 32 Mb GUI destekli AMI UEFI Geçerli BIOS
- “Tak Çalıştır”ı destekler
- ACPI 1.1 Uyumlu Uyandırma Olayları
- Jumpersız ayarlamayı destekler
- SMBIOS 2.3.1 Desteği
- CPU, VCCM, NB, SB Voltaj Çoklu ayarı
- Sürücüler, Yardımcı Programlar, AntiVirüs Yazılımı (Deneme
Sürümü), CyberLink MediaEspresso 6.5 Deneme Sürümü,
Google Chrome Browser ve Toolbar
ASRock 970 Extreme3 R2.0 Motherboard
Türkçe
Arka Panel SATA3
USB 3.0
Konektör
BIOS Özelliği
Destek CD’si
99
Donanım Monitör
- CPU Sıcaklık Duyarlılığı
- Kasa Sıcaklık Duyarlılığı
İS
Sertifikalar
- CPU/Kasa/Güç Fan Takometresi
- CPU/Kasa Sessiz Fan
- CPU/Kasa Fan Çoklu-Hız Kontrolü
- Voltaj İzleme: +12V, +5V, +3,3V, Vcore
- Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM
64-bit / XP / XP 64-bit uyumlu
- FCC, CE, WHQL
- ErP/EuP Hazır (ErP/EuP hazır güç kaynağı gerekli)
* Ayrıntılı ürün bilgileri için lütfen web sitemizi ziyaret edin: http://www.asrock.com
1.3 Jumper'ların Ayarı
Şekilde jumper'ların nasıl ayarlandıkları
gösterilmektedir. Jumper kapağı pinler üzerine
yerleştirildiğinde jumper "Kapalı" dır. Jumper
kapağı pinler üzerindeyken jumper "Açık" tır.
Şekilde pin1 ve pin2'si "Kapalı" olan jumper
kapağı bu 2 pine yerleştirilmiş 3-pinli jumper
gösterilmektedir.
Jumper
CMOS’u temizleme
Ayar
(CLRCMOS1, 3-pinli jumper)
(bkz. s.2 No. 21)
Default
Clear CMOS
Türkçe
Not:CLRCMOS1, CMOS’daki verilerinizi temizlemenize olanak sağlar. Sistem
parametrelerini temizlemek ve varsayılan ayara sıfırlamak için lütfen bilgisayarı
kapatın ve güç kablosunun fişini güç kaynağından çekin. 15 saniye bekledikten
sonra, pin2 ve pin3‘ü CLRCMOS1’de 5 saniye kısaltmak için bir atlatıcı şapkası
kullanın. Ancak, BIOS’u güncelledikten hemen sonra lütfen CMOS’u temizlemeyin.
BIOS’u güncellemeyi tamamladığınızda CMOS’u temizlemeniz gerekirse,
ilk olarak sistemi başlatmanız ve ardından CMOS temizleme işlemini
gerçekleştirmeden önce kapatmanız gereklidir. Parola, tarih, saat, kullanıcı
varsayılan profili, 1394 GUID ve MAC adresinin yalnızca CMOS pili çıkarıldığında
temizleneceğini lütfen aklınızda bulundurunuz.
100
ASRock 970 Extreme3 R2.0 Motherboard
1.4 Yerleşik Fişler ve Konektörler
Yerleşik fişler ve konektörler jumper DEĞİLDİR. Bu fişlerin ve
konektörlerin üzerine jumper kapakları YERLEŞTİRMEYİN.
Fişlerin ve konektörlerin üzerine jumper kapakları yerleştirmek
anakartın kalıcı olarak zarar görmesine neden olabilir!
Seri ATA3 Konektörler
(SATA3_1: bkz. s.2, No. 17) (SATA3_2: bkz. s.2, No. 18) (SATA3_3: bkz. s.2, No. 16) (SATA3_4: bkz. s.2, No. 19) SATA3_5
(SATA3_5: bkz. s.2, No. 20)
SATA3_3
SATA3_1
SATA3_4
SATA3_2
Bu beş Seri ATA3 (SATA3) konektör, dahili depolama cihazları için SATA veri kablolarını destekler. Geçerli SATA3 arayüzü 6,0 Gb/sn veri
aktarım hızına izin verir.
Seri ATA (SATA)
Veri Kablosu
(İsteğe bağlı)
SATA veri kablosunu her iki ucu da SATA3 sabit diskine veya anakarttaki SATA3 konektörüne bağlanabilir.
USB 2.0 Fişleri (9-pinli USB_4_5)
(bkz. s.2 No. 26)
G/Ç panelindeki varsayılan dört USB 2.0 portundan başka, bu anakartta üç USB 2.0 fişi bulunur. Her USB 2.0 fişi iki
USB 2.0 portunu destekler.
(9-pinli USB_6_7)
(bkz. s.2 No. 27)
USB_PWR
P-9
P+9
GND
DUMMY
(9-pinli USB_8_9)
(bkz. s.2 No. 28)
1
Kızılötesi Modülü Fişi
(5-pinli IR1)
(bkz. s.2 No. 29)
Türkçe
GND
P+8
P-8
USB_PWR
Bu fiş, isteğe bağlı bir kablosuz aktarma ve alma kızılötesi modülünü destekler.
ASRock 970 Extreme3 R2.0 Motherboard
101
Kullanıcı Kızılötesi Modül Bağlantısı
(4-pinli CIR1)
Bu fiş, uzaktan kumanda alıcısı
destekler.
(bkz. s.2 No. 25)
Ön Panel Ses Fişi (9-pinli HD_AUDIO1)
(bkz. s.2 No. 32)
1
GND
PRESENCE#
MIC_RET
OUT_RET
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
Bu, panel ses kablosu için
uygun bağlantı sağlayan ve
ses cihazlarını kontrol
etmeyi sağlayan bir arayüzdür.
1. Yükse Tanımlı Ses Jak Duyarlılığını destekler, ancak kasadaki panel kablosunun HDA'nın düzgün çalışmasını desteklemesi gerekir. Lütfen sisteminizi yüklemek için kılavuzumuzdaki ve kasa kılavuzundaki talimatları izleyin.
2. AC'97 ses paneli kullanıyorsanız, lütfen ön panel ses fişine aşağıdaki gibi takın:
A. Mic_IN'i (MIC) MIC2_L'ye bağlayın.
B. Audio_R'yi (RIN) OUT2_R'ye ve Audio_L'yi (LIN) OUT2_L'ye bağlayın.
C. Ground’u (GND) Ground’a (GND) bağlayın.
D. MIC_RET ve OUT_RET yalnızca HD ses paneli içindir. Bunları AC’97 ses paneli için bağlamanız gerekmez.
E. Ön mikrofonu etkinleştirmek için
Windows® XP / XP 64-bit İS için:
“Karıştırıcı”yı seçin. “Kaydedici”yi seçin. Sonra “Ön Mikrofon”u tıklatın.
Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit İS için:
Realtek Kontrol panelinde “Ön Mikrofon” Sekmesine gidin. “Kayıt Ses Seviyesi”ni ayarlayın.
Sistem Paneli Fişi (9-pinli PANEL1)
Bu fiş, birçok sistem ön paneli işlevini barındırır.
(bkz. s.2 No. 23)
Türkçe
102
Kasa üzerindeki güç anahtarını, sıfırlama anahtarını ve sistem durumu göstergesini aşağıdaki pin atamalarına göre bu bağlantıya bağlayın. Kabloları bağlamadan önce pozitif ve negatif pinlere dikkat edin.
PWRBTN (Güç Anahtarı):
Kasa üzerindeki güç anahtarını ön panele bağlayın. Güç anahtarını
kullanarak sisteminizi kapatma şeklinizi yapılandırabilirsiniz.
RESET (Sıfırlama Anahtarı):
Kasa üzerindeki sıfırlama anahtarını ön panele bağlayın. Bilgisayar donarsa veya normal bir yeniden başlatma gerçekleştirilemezse, bilgisayarı yeniden başlatmak için sıfırlama anahtarına basın.
ASRock 970 Extreme3 R2.0 Motherboard
PLED (Sistem Gücü LED’i):
Kasa üzerindeki güç durumu göstergesini ön panele bağlayın. Sistem çalışırken LED yanar. Sistem S1 uyku modunda iken LED yanıp sön
meye devam eder. Sistem S3/S4 uyku modunda veya kapalı (S5) iken LED söner.
HDLED (Sabit Disk Çalışma LED’i):
Kasa üzerindeki sabit disk çalışma LED'ini ön panele bağlayın. Sabit disk
veri okurken veya yazarken LED yanar.
Ön panel tasarımı kasaya göre değişiklik gösterebilir. Ön panel
modülünde temel olarak güç anahtarı, sıfırlama anahtarı, güç LED’i, sabit disk çalışma LED’i, hoparlör vb. bulunur. Kasa ön panel
modülünüzü bu bağlantıya bağlarken, kablo atamalarının ve pin atamalarının doğru biçimde eşleştirildiğinden emin olun.
Kasa Hoparlörü Fişi (4-pinli SPEAKER1)
Lütfen kasa hoparlörünü bu fişe bağlayın.
(bkz. s.2 No. 24)
Güç LED'i Fişi
(3-pinli PLED1)
(bkz. s.2 No. 22)
Sistem gücü durumunu
belirtmek için lütfen kasa güç
LED'ini bu fişe bağlayın. Sistem çalışırken LED açıktır. LED S1 durumunda yanıp sönmeye
devam eder. LED S3/S4
durumunda veya S5 durumun
da (güç kapalı) kapalıdır.
Kasa/güç Fan Konektörü
(4-pinli CHA_FAN1)
(bkz. s.2 No. 12)
(3-pinli CHA_FAN2)
(bkz. s.2 No. 15)
Lütfen kasa fan kablolarını fanına bu konektöre bağlayın ve siyah kabloyu toprak pinine bağlayın. CHA_FAN1/2/3 fan
hızı UEFI veya AXTU yoluyla
kontrol edilebilir.
GND
+12V
CHA_FAN_SPEED
Türkçe
(3-pinli CHA_FAN3)
(bkz. s.2 No. 2)
(3-pinli PWR_FAN1)
(bkz. s.2 No. 10)
ASRock 970 Extreme3 R2.0 Motherboard
103
CPU Fan Konektörü FAN_SPEED_CONTROL
(4-pinli CPU_FAN1)CPU_FAN_SPEED
Lütfen fan kablolarını CPU fanına bu konektöre bağlayın (bkz. s.2 No. 6)
ve siyah kabloyu toprak pinine bağlayın.
+12V
GND
1 2 3 4
Bu anakart 4-Pinli CPU fan (Sessiz Fan) desteği sağlasa da, 3-Pinli CPU fan hızı kontrol işlevi olmadan bile hala başarılı bir şekilde çalışabilir. 3-Pinli CPU fanı bu konektördeki CPU fan konektörüne bağlamayı
planlıyorsanız, lütfen Pin 1-3'e bağlayın.
Pin 1-3 Bağlı
3-Pinli Fanı Takma
(3-pinli CPU_FAN2)
(bkz. s.2 No. 5)
GND
+12V
CPU_FAN_SPEED
ATX Güç Konektörü
(24-pinli ATXPWR1)
12
24
1
13
Lütfen bir ATX güç kaynağını bu konektöre bağlayın.
(bkz. s.2 No. 9)
Bu anakart 24-pinli ATX güç konektörü sağlasa da
geleneksel bir 20-pinli ATX güç kaynağı bağlarsanız da
çalışabilir. 20-pinli ATX güç kaynağını kullanmak için,
lütfen güç kaynağınızı Pin 1 ve Pin 13'le birlikte takın.
20-Pinli ATX Güç Kaynağını Takma
ATX 12V Güç Konektörü
(8-pinli ATX12V1)
(bkz. s.2 No. 1)
Türkçe
5
1
8
4
24
1
13
Lütfen bir ATX 12V güç kaynağını bu konektöre bağlayın.
Bu anakart 8-pinli ATX 12V güç konektörü sağlasa da geleneksel bir
4-pinli ATX 12V güç kaynağı bağlarsanız da çalışabilir. 4-pinli ATX güç
kaynağını kullanmak için, lütfen güç kaynağınızı Pin 1 ve Pin 5'le birlikte
5
takın.
4-Pinli ATX 12V Güç Kaynağını Takma
104
12
ASRock 970 Extreme3 R2.0 Motherboard
8
1
4
Seri port Fişi (9-pinli COM1) Bu COM1 fişi bir seri port modülünü destekler.
(bkz. s.2 No. 30)
HDMI_SPDIF Fişi
(2-pinli HDMI_SPDIF1) (bkz. s.2 No. 31)
Vbus
IntA_P3_SSRXIntA_P3_SSRX+
GND
IntA_P3_SSTXIntA_P3_SSTX+
GND
IntA_P3_DIntA_P3_D+
DUMMY
I/O panelinde bulunan iki adet
varsayılan USB 3.0 bağlantı
noktasının yanı sıra, bu ana
kart üzerinde bir adet USB 3.0
bağlantısı bulunur. Bu USB 3.0
bağlantısı iki adet USB 3.0
bağlantı noktasını
destekleyebilir.
Türkçe
USB 3.0 Fişleri (19-pinli USB3_2_3)Vbus
IntA_P2_SSRX(bkz. s.2 No. 38)
IntA_P2_SSRX+
GND
IntA_P2_SSTX
IntA_P2_SSTX+
GND
IntA_P2_D
IntA_P2_D+
HDMI_SPDIF fişi, SPDIF ses çıkışını HDMI VGA kartına sağlar, sistemin HDMI Dijital
TV/projektör/LCD cihazlarını bağlamasına izin verir. Lütfen HDMI VGA kartının
HDMI_SPDIF konektörünü bu fişe bağlayın.
ASRock 970 Extreme3 R2.0 Motherboard
105
2. BIOS Bilgileri
Anakarttaki Flash Bellek BIOS Ayarları Yardımcı Programını içerir. Bilgisayarı
başlattığınızda, lütfen Otomatik Güç Sınaması (POST) sırasında BIOS Ayarları
yardımcı programına girmek için <F2> veya <Del> tuşuna basın; aksi halde, POST
test rutinlerine devam eder. BIOS Ayarlarına POST'tan sonra girmek istiyorsanız,
lütfen <Ctl> + <Alt> + <Delete> tuşlarına basarak veya sistem kasasındaki sıfırlama
düğmesine basarak sistemi yeniden başlatın. BIOS Ayarları programı kullanıcı
dostu olacak şekilde tasarlanmıştır. Çeşitli alt menüler arasında dolaşmanıza ve
önceden belirlenen seçenekler arasından seçim yapmanıza izin veren menü tabanlı
bir programdır. BIOS Ayarları hakkında ayrıntılı bilgi için, lütfen Destek CD'sinde
bulunan Kullanıcı Kılavuzu'na (PDF dosyası) başvurun.
3. Yazılım Destek CD’si bilgileri
Bu anakart çeşitli Microsoft® Windows® işletim sistemleri destekler: 8 / 8 64-bit / 7 / 7
64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Anakartla birlikte gelen Destek CD'si
anakart özelliklerini genişleten gerekli sürücüleri ve kullanışlı yardımcı programları
içerir. Destek CD'sini kullanmaya başlamak için, CD'yi CDROM sürücünüze takın.
Bilgisayarınızda "OTOMATİK KULLAN" özelliği etkinleştirilmişse, Ana Menüyü
otomatik olarak görüntüler. Ana Menü otomatik olarak görüntülenmezse, menüleri
görüntülemek için Destek CD'sinin “BIN” klasöründeki "ASSETUP.EXE" dosyasını
bulun ve çift tıklatın.
Türkçe
106
ASRock 970 Extreme3 R2.0 Motherboard
1. 제품소개
ASRock 의 970 Extreme3 R2.0 메인 보드를 구매하여 주신것에 대하여 감사 드립니
다 . 이 메인보드는 엄격한 품질관리 하에 생산되어진 신뢰성 있는 메인보드 입니다 .
이 제품은 고 품격 디자인과 함께 ASRock 의 우수한 품질과 최고의 안정성을 자랑하
고 있습니다 . 이 빠른 설치 안내서에는 마더보드에 대한 설명과 단계별 설치 방법이
실려 있습니다 . 마더보드에 대한 보다 자세한 내용은 지원 CD 의 사용 설명서에서 확
인할 수 있습니다 .
메인보드의 사양이나 바이오스가 업 데이트 되기 때문에 이 사용자
설명서의 내용은 예고 없이 변경되거나 바뀔 수가 있습니다 . 만일을
생각해서 이 사용자 설명서의 어떤 변경이 있으면 ASRock 의 웹
사이트에서 언제든지 업 데이트를 하실 수 있습니다 . 웹사
이트에서 최신 VGA 카드와 CPU 지원 목록을 확인할 수 있습니다 .
ASRock 의 웹사이트 주소는 http://www.asrock.com 입니다 .
본 머더보드와 관련하여 기술 지원이 필요한 경우 당사 웹 사이트를 방문하
여 사용 중인 모델에 대한 특정 정보를 얻으십시오 .
www.asrock.com/support/index.asp
1.1 패키지 내용
ASRock 970 Extreme3 R2.0 마더보드 (ATX 폼 팩터 )
ASRock 970 Extreme3 R2.0 퀵 설치 가이드
ASRock 970 Extreme3 R2.0 지원 CD
시리얼 ATA (SATA) 데이터 케이블 2 개 ( 선택 사양 )
I/O 차폐 1 개
ASRock은사용자에게 알립니다 ...
®
한국어
Windows 8 / 8 64-비트 / 7 / 7 64-비트 / VistaTM / VistaTM 64-비트의
성능을 향상시키기 위해서 Storage Configuration(스토리지 구성)에서
BIOS 옵션을 AHCI 모드로 설정하는 것이 좋습니다. BIOS 설정과 관련하
여 자세한 내용은 지원 CD에 포함된 “사용 설명서”를 참조하십시오.
ASRock 970 Extreme3 R2.0 Motherboard
107
1.2 설명서
플랫폼
한국어
CPU
칩셋
메모리
확장 슬롯
오디오
랜
108
- ATX 폼 팩터
- 완전 고체 축전지 디자인 (100% 일제 고품질 기능성 고분자 콘
덴서 )
- Socket AM3+ 프로세서에 대한 지원
- Socket AM3 프로세서에 대한 지원 : AMD PhenomTM II X6 /
X4 / X3 / X2 (920/940 제외 ) / Athlon II X4 / X3 / X2 /
Sempron 프로세서
- 8- 코어 CPU 지원
- UCC (Unlock CPU Core) 지원
- Digi 전원 설계
- 4 + 1 전원 위상 디자인
- 최대 140W 까지 CPU 지원
- AMD 의 Cool ‘n’ QuietTM 기술 지원
- FSB 2400 MHz (4.8 GT/s)
- 언타이드 오버클러킹 (Untied Overclocking) 기술 지원
- 하이퍼 트랜스포트 3.0 (HT 3.0) 기술 지원
- 노스브릿지 : AMD 970
- 사우스 브릿지 : AMD SB950
- 듀얼 채널 메모리 기술 지원
- DDR3 DIMM 슬롯 4 개
- DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/1333/1066/
800 비 -ECC, 언버퍼드 메모리를 지원
- 최대 시스템 메모리 용량 : 32GB
- 2 x PCI Express 2.0 x16 슬롯
(PCIE2: x16 모드 ; PCIE4: x4 모드 )
- 2 개의 PCI Express 2.0 x1 슬롯
- 2 개의 PCI 슬롯
- AMDTM Quad CrossFireXTM 및 CrossFireXTM 지원
- 7.1 CH HD Audio 목록 보호
(Realtek ALC892 Audio Codec)
- Premium Blu-ray 오디오 지원
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- 웨이크 - 온 - 랜 지원
- LAN 케이블 감지 지원
- 절전형 이더넷 802.3az 지원
- PXE 지원
ASRock 970 Extreme3 R2.0 Motherboard
SATA3
USB 3.0
온보드 헤더
및 커넥터
BIOS
I/O Panel
- 1 개 PS/2 마우스 포트
- 1 개 PS/2 키보드 포트
- 1 개동축 SPDIF 출력 포트
- 1 개광학 SPDIF 출력 포트
- 4 개디폴트 USB 2.0 포트
- 2 개디폴트 USB 3.0 포트
- 1 개 eSATA3 커넥터
- 1 개 LED(ACT/LINK LED 및 SPEED LED) 가 있는 RJ-45 LAN 포트
- 오디오 잭 : 측면 스피커 / 후방 스피커 / 중앙 / 저음 / 라인 인 / 전방 스피커 / 마이크
- SATA3 6.0 Gb/s 커넥터 5 개 . RAID (RAID 0, RAID 1,
RAID 5 및 RAID 10), NCQ, AHCI 및 “ 핫 플러그 ” 기능 지원
- Etron EJ188H 에 의한 후면 패널 USB 3.0 포트 2 개 , 최고
5Gb/s 의 USB 1.1/2.0/3.0 지원
- Etron EJ188H 에 의한 전면 패널 USB 3.0 헤더 1 개 (USB 3.0
포트 2 개 지원 ), 최고 5Gb/s 의 USB 1.1/2.0/3.0 지원
- 5 개 의 SATA3 6.0Gb/s 커넥터
- 적외선 모듈 헤더 1 개
- 소비자용 적외선 모듈 헤더 1 개
- COM 포트 헤더 1 개
- HDMI_SPDIF 헤더 1 개
- 전원 LED 헤더 1 개
- CPU 팬 커넥터 2 개 (4 핀 1 개 , 3 핀 1 개 )
- 섀시 팬 커넥터 3 개 (4 핀 1 개 , 3 핀 2 개 )
- 전원 팬 커넥터 1 개 (3 핀 )
- 24 핀 ATX 전원 헤더
- 8 핀 ATX 12V 파워 콘넥터
- 전면부 오디오 콘넥터
- USB 2.0 헤더 3 개 (6 개의 추가 USB 2.0 포트를 지원하는 헤더 2개)
- USB 3.0 헤더 1 개 (2 개의 추가 USB 3.0 포트를 지원하는헤더
2개)
- 32Mb GUI 지원을 제공하는 AMI UEFI 적합형 BIOS
-“플러그 앤 플레이”지원
- ACPI 1.1 웨이크 - 업 이벤트와의 호환
- 점퍼 프리 지원
- 점퍼 프리 지원 ; SMBIOS 2.3.1 지원
- CPU, VCCM, NB, SB 전압 멀티 조절
ASRock 970 Extreme3 R2.0 Motherboard
한국어
후면판 I/O
109
지원 CD
하드웨어 모니터
OS
인증서
- 드라이버 , 유틸리티 , 안티바이러스 소프트웨어 ( 시험판 ),
CyberLink MediaEspresso 6.5 평가판 , Google Chrome
Browser 및 Toolbar
- CPU 온도 감지
- 마더보드 온도 감지
- CPU/ 섀시 / 전원 팬 회전 속도계 : 샤시 ( 케이스 ) 팬 회전 속도
계
- CPU/ 섀시 소음팬
- CPU/ 섀시 팬 멀티스피드 컨트롤
- 전압 감시 기능 : +12V,+5V,+3.3V,Vcore
®
- 마이크로 소프트 Windows 8/8 64 비트 /7/7 64 비트 /VistaTM/
TM
Vista 64 비트 /XP/XP 64 비트 와 호환
- FCC, CE, WHQL
- ErP/EuP 지원 (ErP/EuP 지원 전원 공급기가 요구됨 )
* 상세한 제품정보는 당사의 웹사이트를 방문할수있습니다 . http://www.asrock.com
한국어
110
ASRock 970 Extreme3 R2.0 Motherboard
1.3 점퍼 셋팅
그림은 점퍼를 어떻게 셋업 하는지를 보여줍니다 .
점퍼 캡이 핀 위에 있을 때 , 점퍼는 “ 쇼트 ” 입니다 .
점퍼 캡이 핀 위에 없을 때 점퍼는 “ 오픈 ” 입니다 .
그림은 3 개의 핀 중 1-2 번 핀이 “ 쇼트 ” 임을
보여주는 것이며 , 점퍼 캡이 이 두 핀 위에 있음을
보여주는 것입니다 .
점퍼
세팅
CMOS 초기화
(CLRCMOS1, 3 핀 점퍼 )
(2 페이지 , 21 번 항목 참조 )
기본 설정
CMOS 삭제
한국어
참고 :CLRCMOS1 을 사용하여 CMOS 에 들어 있는 데이터를 삭제할 수 있습니다 .
시스템 매개변수를 삭제하고 기본 설정으로 복원하려면 , 컴퓨터를 끄고 전원
공급장치에서 플러그를 뽑으십시오 . 15 초를 기다린 다음 점퍼 캡을 사용하여
CLRCMOS1 의 핀 2 와 핀 3 을 5 초 동안 단락하십시오 . 그러나 BIOS 업데이트
직후에는 CMOS 를 삭제하지 마십시오 . BIOS 를 업데이트하자마자 CMOS 를
삭제해야 하는 경우 먼저 시스템을 부팅하고 CMOS 를 종료하고 삭제 작업을 해
야 합니다 . CMOS 배터리를 제거할 경우에만 암호 , 날짜 , 시간 , 사용자 기본 프
로파일 , 1394 GUID, MAC 주소가 삭제됩니다 .
ASRock 970 Extreme3 R2.0 Motherboard
111
1.4 온보드 헤더 및 커넥터
주의 !
세요 . 커넥터에 점퍼 캡을 설치하면 마더보드가 영구적으로 손상됩니다 !
이 콘넥터는 점퍼가 아닙니다 . 이 콘넥터 위에 점퍼 캡을 사용하지마
시리얼 ATA3 커넥터
(SATA3_1: 2 페이지 , 17 번 항목 참조 ) (SATA3_2: 2 페이지 , 18 번 항목 참조 ) SATA3_5
(SATA3_3: 2 페이지 , 16 번 항목 참조 ) (SATA3_4: SATA3_3
SATA3_1
SATA3_4
SATA3_2
5 개의 시리얼 ATA3 (SATA3) 커넥터는 내부 저장 장치용 SATA 데이터 케이블
을지원합니다 . 커넥터가 내부
기억 장치용 SATA 케이블을 지원합니다 . 현재의 SATA3
인터페이스는 최고 6.0 Gb/s 의 데이터 전송 속도를지원합니다 .
2 페이지 , 19 번 항목 참조 )
(SATA3_5:
2 페이지 , 20 번 항목 참조 )
시리얼 ATA(SATA) 데이터 케이블
SATA 데이터 케이블의 임의
적인 측을 마더보드의 SATA /
SATAII / SATA3 하드 디스크
혹은 SATA3 커넥터에 연결합
( 선택 사양 )
니다 .
USB 2.0 헤더
(9 핀 USB_4_5)
본 머더보드에는 I/O 패널에 있
는 4 개의 기본 USB 2.0 포트 외에도 USB 2.0 헤더가 3 개 있
습니다 . 각각의 USB 2.0 헤더
는 2 개의 USB 2.0 포트를 지원
할 수 있습니다 .
(2 페이지 , 26 번 항목 참조 )
(9 핀 USB_6_7)
(2 페이지 , 27 번 항목 참조 )
한국어
USB_PWR
P-9
P+9
GND
DUMMY
(9 핀 USB_8_9)
(2 페이지 , 28 번 항목 참조 )
1
GND
P+8
P-8
USB_PWR
112
ASRock 970 Extreme3 R2.0 Motherboard
적외선 모듈 헤더
(5 핀 IR1)
(2 페이지 , 29 번 항목 참조 )
이 헤더는 선택품목인 무선
적외선 송수신 모듈을
지원합니다 .
소비자용 적외선 모듈 헤더
(4 핀 CIR1)
(2 페이지 , 25 번 항목 참조 )
이 헤더는 리모콘 수신기
연결하는 데 사용될
수 있습니다 .
전면부 오디오 콘넥터
(9 핀 HD_AUDIO1) ( 2 페이지 , 32 번 항목 참조 ) GND
PRESENCE#
MIC_RET
OUT_RET
1
이 콘넥터는 오디오 장치를
편리하게 조절하고 연결할 수 있는 전면 오디오 인터페이스 입니다 .
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1.
High Definition Audio( 고음질 오디오 ) 는 잭 센스 기능을 지원하나 , 제
대로작동하려 면 섀시의 패널 와이어가 HAD 를 지원해야 합니다 . 이 설
명서 및 섀시 설명서의지침 을 따라 시스템을 설치하십시오 .
2.
AC’97 오디오 패널을 사용하는 경우 , 이를 아래와 같이 프런트 패널
의 오디오헤 더에 설치하십시 오 .
A.
Mic_IN (MIC) 을 MIC2_L 에 연결합니다 .
B.
Audio_R (RIN) 을 OUT2_R 에 연결하고 , Audio_L (LIN) 을 OUT2_L 에 연결합 니다 .
C.
Ground (GND) 을 Ground (GND) 에 연결합니다 .
D.
MIC_RET 및 OUT_RET 는 HD 오디오 패널 전용입니다 . 이들을 AC’97 오디오 패널에 연결 하지 않아도 됩니다 .
E.
앞면 마이크 작동 .
®
Windows XP / XP 64 비트 OS 의 경우 :
“Mixer” ( 믹서 ) 와 “Recorder” ( 리코더 ) 를 선택한 후
“FrontMic” ( 앞면 마이크 ) 를 선택합니다 .
Windows 8 / 8 64 비트 / 7 / 7 64 비트 / VistaTM / VistaTM 64
비트 OS 의 경우 :
Realtek 제어판에서 “FrontMic” ( 앞면 마이크 ) 로 가서
“Recording Volume” ( 리코딩 볼륨 ) 을 조정합니다 .
시스템 콘넥터
(9 핀 PANEL1) (2 페이지 , 23 번 항목 참조 ) 한국어
®
이 콘넥터는 시스템 전면 패
널기능을 지원하기 위한
것입니다 .
ASRock 970 Extreme3 R2.0 Motherboard
113
섀시의 전원 스위치 , 리셋 스위치 , 시스템 상태 표시등을 아래의 핀 할당
에 따라 이헤더에 연결합니다 . 케이블을 연결하기 전에 양극 핀과 음극 핀
을 기록합니다 .
PWRBTN( 전원 스위치 ):
섀시 전면 패널의 전원 스위치에 연결합니다 . 전원 스위치를 이용해 시스
템을 끄는방법을 구성할 수 있습니다 .
RESET( 리셋 스위치 ):
섀시 전면 패널의 리셋 스위치에 연결합니다 . 컴퓨터가 정지하고 정상적 재시작을수행하지 못할 경우 리셋 스위치를 눌러 컴퓨터를 재시작합니
다.
PLED( 시스템 전원 LED):
섀시 전면 패널의 전원 상태 표시등에 연결합니다 . 시스템이 작동하고 있
을 때는 LED 가 켜져 있습니다 . 시스템이 S1 대기 상태에 있을 때는 LED
가 계속 깜박입니다 . 시스템이 S3/S4 대기 상태 또는 전원 꺼짐 (S5) 상태
에 있을 때는 LED 가 꺼져 있습니다 .
HDLED( 하드 드라이브 동작 LED):
섀시 전면 패널의 하드 드라이브 동작 LED 에 연결합니다 . 하드 드라이
브가 데이터를 읽거나 쓰고 있을 때 LED 가 켜져 있습니다 .
전면 패널 디자인은 섀시별로 다를 수 있습니다 . 전면 패널 모듈은 주로 전원 스위치 , 리셋 스위치 , 전원 LED, 하드 드라이브 동작 LED, 스피커 등으로 구성되어 있습니다 . 섀시 전면 패널 모듈을 이 헤더에 연결할 때 와이어 할당과 핀 할당이 정확히 일치하는지 확인합니다 .
새시 스피커 헤더
(4 핀 SPEAKER 1)
새시 스피커를 이 헤더에
연결하십시오 .
(2 페이지 , 24 번 항목 참조 )
전원 LED 헤더
핀 PLED1)
(2 페이지 , 22 번 항목 참조 )
한국어
114
시스템 전원 상태를 표시하려(3
면 섀시 전원 LED 를 헤더에 연
결하십시오 . 시스템 작동 중에
는 LED 에 전원이 켜져 있습니
다 . S1 상태에서는 LED 가 계
속 깜박입니다 . S3/S4 상태 또
는 S5 상태에서는 LED 가 꺼집
니다 ( 전원 꺼짐 ).
ASRock 970 Extreme3 R2.0 Motherboard
섀시 및 전원 팬 커넥터
팬 케이블을 팬 커넥터에 연결하
(4 핀 CHA_FAN1)고 접지 핀에는 검은색 전선을
(2 페이지 , 12 번 항목 참조 )
연결하십시오 . CHA_FAN1/2/3
팬 속도는 UEFI 또는 AXTU 를
(3 핀 CHA_FAN2)
GND
통하여 제어할 수 있습니다 .
+12V
(2 페이지 , 15 번 항목 참조 )
CHA_FAN_SPEED
(3 핀 CHA_FAN3)
(2 페이지 , 2 번 항목 참조 )
(3 핀 PWR_FAN1)
(2 페이지 , 10 번 항목 참조 )
CPU 팬 커넥터
(4 핀 CPU_FAN1)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
(2 페이지 , 6 번 항목 참조 )
+12V
GND
CPU 팬 케이블을 이 커넥터에 연결하고 흑색 선을 접지 핀에 맞추십시오 .
1 2 3 4
본 머더보드가 4 핀 CPU 팬 ( 저소음 팬 ) 지원을 제공하기는 하지만 팬 속
도 제어기능없이도 3 핀 CPU 팬을 성공적으로 작동할 수 있습니다 . 본 머
더보드의 CPU 팬 커넥터에 3 핀 CPU 팬을 연결하려면 1-3 번 핀에 연결
하십시오 .
1-3 번 핀에 연결됨
3 핀 팬 설치
(3 핀 CPU_FAN2)
(2 페이지 , 5 번 항목 참조 )
ATX 전원 헤더
(24 핀 ATXPWR1)
GND
+12V
CPU_FAN_SPEED
12
24
1
13
ATX 전원 공급기를 이 헤더에 연결하십시오 .
이 마더보드는 24 핀 ATX 전원 커넥터를 제공하지만 ,
종래의 20 핀 ATX 전원 공급장치를 사용해도 작동이
가능합니다 . 20 핀 ATX 전원 공급장치를 사용하려면 ,
Pin 1 과 Pin 13 으로 전원공급장치를 연결하십시오 .
12
24
20 핀 ATX 전원 공급장치 설치
1
13
ASRock 970 Extreme3 R2.0 Motherboard
한국어
(2 페이지 , 9 번 항목 참조 )
115
ATX 12V 파워 콘넥터 (8 핀 ATX12V1) (2 페이지 , 1 번 항목 참조 )
5
1
8
4
ATX 12V 플러그가 달린
전원공급장치를 이 커넥터에 연결해야 충분한 전력을
공급할 수 있습니다 . 그러지
않을 경우 전원을 켤 수
없습니다 .
비록 본 마더보드는 8- 핀 ATX 12V 전원 연결기를 제공하지만 이것은 여전히작업할수있습니다 . 만약 전통적인 4- 핀 ATX 12V 전원공급을 채
용하여 4- 핀 ATX 전력을 사용하는경우 , 반드시 전원 공급을 핀 1 과 핀
5 에전원공급을 삽입해야합니다 .
5
1
4- 핀 ATX 12V 전원공급장치
시리얼포트 컨넥터
(9 핀 COM1)
8
4
이 콘넥터는 시리얼 포트
모듈을 지원합니다 .
(2 페이지 , 30 번 항목 참조 )
HDMI_SPDIF 헤더
(2 핀 HDMI_SPDIF1)
HDMI VGA 카드에 SPDIF 오
디오 출력을 제공하는
HDMI_SPDIF 헤더는 시스템
이 HDMI 디지털 TV/ 프로젝
터 /LCD 장치에 연결할 수 있
게 합니다 . HDMI VGA 카드의
HDMI_SPDIF 커넥터를 이 헤
더에 연결하십시오 .
(2 페이지 , 31 번 항목 참조 ) USB 3.0 헤더
(19 핀 USB3_2_3)
Vbus
Vbus
(2 페이지 , 38 번 항목 참조 )
한국어
116
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
I/O 패널에 있는 2 개의 기본적
USB 3.0 포트 이외에도 마더보
드에 1 개의 USB 3.0 헤더가 있
습니다 . 이 USB 3.0 헤더는 2 개
의 USB 3.0 포트를 지원할 수 있
습니다 .
ASRock 970 Extreme3 R2.0 Motherboard
2. 시스템 바이오스 정보
메인보드의 플래쉬 메모리에는 바이오스 셋업 유틸리티가 저장되어 있습니다 .
컴퓨터를 사용하실 때 , “자가진단 테스트”(POST) 가 실시되는 동안 <F2> 또는
<Del> 키를 눌러 바이오스 셋업으로 들어가세요 ; 만일 그렇게 하지 않으면 POST
는 테스트 루틴을 계속하여 실행할 것입니다 . 만일 POST 이후 바이오스 셋업을 하
기 원하신다면 ,<Ctl>+<Alt>+<Delete> 키를 누르거나 , 또는 시스템 본체의 리셋
버튼을 눌러 시스템을 재 시작하여 주시기 바랍니다 . 바이오스 셋업 프로그램은 사용
하기 편하도록 디자인되어 있습니다 . 각 항목은 다양한 서브 메뉴 표가 올라오며 미
리 정해진 값 중에서 선택할 수 있도록 되어 있습니다 . 바이오스 셋업에 대한 보다 상
세한 정보를 원하신다면 보조 CD 안의 포함된 사용자 매뉴얼 (PDF 파일 ) 을 따라 주
시기 바랍니다 .
3. 소프트웨어 지원 CD 정보
한국어
이 메인보드는 여러 가지 마이크로소프트 윈도우 운영 체계를 지원합니다 :
8/8 64 비트 /7/7 64 비트 /VistaTM/VistaTM 64 비트 /XP/XP 64 비트 . 메인보드에 필
요한 드라이버와 사용자 편의를 위해 제공되는 보조 CD 는 메인보드 의 기능을 향상
시켜 줄 것입니다 . 보조 CD 를 사용하여 시작하시려면 , CD-ROM 드라이브에 CD 를
넣어주시기 바랍니다 . 만일 고객님의 컴퓨터가 “AUTORUN” 이 가능하다면 자동
으로 메인 메뉴를 모니터에 디스플레이 시켜 줄 것입니다 . 만일 자동으로 메인 메뉴
가 나타나지 않는다면 , 보조 CD 의 디스플레이 메뉴 안에 있는 BIN 폴더 ASSETUP.
EXE 파일을 더블 클릭하여 주시기 바랍니다 .
(D: \ BIN \ ASSETUP.EXE, D: 는 CD-ROM 드라이브 )
ASRock 970 Extreme3 R2.0 Motherboard
117
1、 はじめに
ASRock 970 Extreme3 R2.0 マザーボードをお買い上げいただきありがとうございます。
本製品は、弊社の厳しい品質管理の下で製作されたマザーボードです。本製品は、弊社の
品質と耐久性の両立という目標に適合した堅牢な設計により優れた性能を実現します。こ
のクイックインストレーションガイドには、マザーボードの説明および段階的に説明したイン
ストレーションの手引きが含まれています。マザーボードに関するさらに詳しい情報は、「サ
ポート CD」のユーザーマニュアルを参照してください。
1.1
マザーボードの仕様および BIOS ソフトウェアは、アップデートされること
が有りますので、マニュアルの内容は、予告なしに変更されることがあり
ます。本マニュアルに変更が有った場合は、弊社のウェブサイトに通告な
しに最新版のマニュアルが掲載されます。最新の VGA カードおよび CPU サ
ポートリストもウェブサイトでご覧になれます。ASRock 社ウェブサイト:
http://www.asrock.com
このマザーボードに関連する技術サポートが必要な場合、当社の Web サイト
にアクセスし、使用しているモデルについての特定情報を見つけてくださ
い。 www.asrock.com/support/index.asp
パッケージ内容
ASRock 970 Extreme3 R2.0 マザーボード (ATX フォームファクター )
ASRock 970 Extreme3 R2.0 クイックインストレーションガイド
ASRock 970 Extreme3 R2.0 サポート CD
2 x シリアル ATA (SATA) データケーブル(オプション)
1 x I/O パネルシールド
ASRockからのお知らせ ...
Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64bit でより良い性能を得るには、ストレージ構成のBIOSオプションをAHCIモー
ドに設定することを推奨します。 BIOSのセットアップについての詳細は、サポー
トCDの「ユーザーマニュアル」を参照してください。
日本語
118
ASRock 970 Extreme3 R2.0 Motherboard
仕様
プラットフ
CPU
ヱップセット
メモリー
拡張スロット
オーディオ
LAN
- ATX フォームファクター
- 全ソリッド・キャパシター設計 (100% 日本製の高品質導電性高分
子電解コンデンサー )
- Socket AM3+ プロセッサのサポート
- Socket AM3 プロセッサのサポート :AMD PhenomTM II X6 / X4 / X3 / X2(920 / 940 を除く ) / Athlon II X4 / X3 / X2 / Sempron プロセッサ
- 8-Core CPU 搭載
- UCC (Unlock CPU Core) をサポート
- デジタル電源設計
- 4 + 1 電源位相設計
- 140W まで CPU をサポート
- AMD 社 Cool ‘n’ QuietTM をサポート
- FSB 2400 MHz (4.8 GT/s)
- Untied Overclocking をサポート
- Hyper-Transport 3.0 (HT 3.0) をサポート
- ノースブリッジ : AMD 970
- サウスブリッジ : AMD SB950
- デュアルヱャンネル DDR3 メモリーテクノロジー
- DDR3 DIMM スロット x 4
- DDR3 2100+(OC)/1866(OC)/1800(OC)/1600(OC)/1333/
1066/800 non-ECC, un-buffered メモリーに対応
- システムメモリの最大容量 : 32GB - 2 x PCI Express 2.0 x16 スロット
(PCIE2: x16 モード、PCIE4: x4 モード )
- 2 x PCI Express 2.0 x1 スロット
- 2 x PCI スロット
- AMDTM Quad CrossFireXTM および CrossFireXTM をサポート
- 7.1 CH HD オーディオ ( コンテンツ保護付 )
(Realtek ALC892 オーディオ Codec)
- Premium Blu-ray オーディオのサポー
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Wake-On-LAN をサポート
- LAN ケーブル検出をサポート
- Energy Efficient Ethernet 802.3az をサポート
- PXE に対応
ASRock 970 Extreme3 R2.0 Motherboard
日本語
1.2
119
リアパネル I/O
SATA3
日本語
USB 3.0
コネクター
BIOS 関連機能
120
I/O Panel
- PS/2 マウスポート x 1
-
PS/2 キーボードポート x 1
同軸 SPDIF 出力ポート x 1
光学 SPDIF 出力ポート x 1
Ready-to-Use USB 2.0 ポート x 4
Ready-to-Use USB 3.0 ポート x 2
eSATA3 ポート x 1
LED(ACT/LINK LED および SPEED LED)付き
RJ-45 LAN ポート x 1
- オーディオジャック:側面のスピーカー、後部スピー
カー、中央低音、入力、前部スピーカー、マイク入力
- SATA3 6.0 Gb/ 秒のコネクタ 5 機が、RAID (RAID 0、RAID 1、
RAID 5、RAID 10) をサポート、NCQ、AHCI および “Hot Plug”
( ホットプラグ ) 機能
- 2 x リア USB 3.0 ポート (Etron EJ188H)、USB 1.1/2.0/3.0
に最高 5Gb/s まで対応
- 1 x フロント USB 3.0 ヘッダ (USB 3.0 ポート 2 基対応 )
Etron EJ188H、USB 1.1/2.0/3.0 に最高 5Gb/s まで対応
- 5 x SATA3 6.0Gb/ 秒コネクタが
- IR ヘッダー x 1
- コンシューマー赤外線モジュールヘッダー x 1
- COM ポートヘッダ x 1
- HDMI_SPDIF ヘッダー x 1
- 電源 LED ヘッダー x 1
- CPU ファンコネクタ x 2 (4 ピン x 1、3 ピン x 1)
- シャーシファンコネクタ x 3 (4 ピン x 1、3 ピン x 2)
- 電源ファンコネクタ x 1 (3 ピン )
- 24 ピン ATX 電源コネクター
- 8 ピン 12V 電源コネクター
- フロントパネルオーディオコネクター
- USB 2.0 ヘッダー (USB 2.0 用 6 ポートをサポート ) x 3
- USB 3.0 ヘッダー (USB 3.0 用 2 ポートをサポート ) x 1
- 32Mb AMI UEFI Legal BIOS(GUI サポート)
- プラグ&プレイをサポート
- ACPI 1.1 準拠ウェイクアップイベント
- jumperfree モードサポート
- SMBIOS 2.3.1 サポート
- CPU、VCCM、NB、SB ブリッジ電圧
ASRock 970 Extreme3 R2.0 Motherboard
サポート CD
モニター
OS
認証
- ドライバー、ユーティリティ、アンチウィルスソフト ウェアハードウェア
( 体験版 )、 CyberLink MediaEspresso 6.5 試用版、
Google Chrome Browser および Toolbar
- CPU 温度検知
- マザーボード温度検知
- CPU/ シャーシ / 電源ファンタコメータ
- CPU/ シャーシクワイエットファン
- CPU/ シャーシファンマルチ速度制御
- 電源モニター : +12V, +5V, +3.3V, Vcore
- Microsoft® Windows® 8/8 64-bit/7/7 64-bit/VistaTM/
VistaTM 64-bit/XP/XP 64-bit compliant
- FCC, CE, Microsoft® WHQL 認証済み
- ErP/EuP 対応(ErP/EuP 対応の電源装置が必要です)
日本語
* 製品の詳細については、http://www.asrock.com を御覧なさい。
ASRock 970 Extreme3 R2.0 Motherboard
121
1.3
ジャンパ設定
右の図はジャンパがどのように設定されているかを示しま
す。ジャンパキャップがピンに置かれている場合、ジャンパ
は “ショート” になります。ジャンパキャップがピンに置か
れていない場合、ジャンパ は “オープン”になります。右の
図で、3ピンジャンパで、1-2 ピンを “ショート”の場合、こ
れらの2つのピンにジャンパキャップを置きます。
ジャンパ
CMOS の消去ジャンパ
設定
説明
(CLRCMOS1)
( ページ2アイテム 21 参照)
デフォルト設定
CMOS の消去
注 :CLRCMOS1 により、CMOS のデータをクリアできます。システムパラメータをクリアしデフォルト設定にリ
セットするには、コンピュータの電源をオフにし、電源装置から電源コードを抜いてください。15 秒待って
から、ジャンパキャップを使用して CLRCMOS1 のピン 2 とピン 3 を 5 秒間ショートしてください。ただし、
BIOS 更新の後すぐには CMOS をクリアしないでください。BIOS の更新の終了後直ちに CMOS をクリア
する必要がある場合、まずシステムを起動してからシャットダウンし、その後クリア CMOS アクションを実
行する必要があります。パスワード、日付、時刻、ユーザーデフォルトのプロファイルを忘れずにメモして
ください。1394 GUID と MAC アドレスは、CMOS バッテリを取り外した場合のみ消去されます。
日本語
122
ASRock 970 Extreme3 R2.0 Motherboard
1.4
オンボードのヘッダとコネクタ類
オンボードのヘッダとコネクタ類はジャンパではありません。それらのヘッ
ダやコネクタにジャンパキャップをかぶせないでください。ヘッダやコネクタ
にジャンパキャップをかぶせると、マザーボードに深刻な影響を与える場
合があります。
シリアル ATA3 コネクタ
SATA3_1:
ページ 2, アイテム 17 を参照 SATA3_3
SATA3_1
SATA3_4
SATA3_2
SATA3_2: ページ 2, アイテム 18 を参照 SATA3_5
SATA3_3:
ページ 2, アイテム 16 を参照
これら 5 本のシリアル ATA3
(SATA3)コネクタは内蔵スト
レーデバイスに使用する SATA
データケーブルに対応していま
す。現在の SATA3 インタフェー
スの最大データ転送速度は
6.0 Gb/s です。
SATA3_4:
ページ 2, アイテム 19 を参照
SATA3_5:
ページ 2, アイテム 20 を参照
シリアル ATA(SATA)
データケーブル(オプション)
SATA データケーブルのどちらかの
端をマザーボードの SATA /SATAII /
SATA3 ハードディスク、または SATA3 コ
ネクタに接続できます。
USB 2.0 ヘッダ
(9 ピン USB_4_5)
I/O パネルには、デフォルトの 4
つの USB 2.0 ポート以外に、この
マザーボードに 3 つの USB 2.0
ヘッダが搭載されています。それ
ぞれの USB 2.0 ヘッダは 2 つの
USB 2.0 ポートをサポートできま
す。
ページ2, アイテム 26 を参照
(9 ピン USB_6_7)
ページ2, アイテム 27 を参照
ページ2, アイテム 28 を参照
日本語
USB_PWR
P-9
P+9
GND
DUMMY
(9 ピン USB_8_9)
1
GND
P+8
P-8
USB_PWR
赤外線モジュールコネクタ
(5 ピン IR1)
このコネクタは赤外線の無線送受信
モジュールに対応します。
ページ2, アイテム 29 を参照
ASRock 970 Extreme3 R2.0 Motherboard
123
コンシューマー赤外線モジュールヘッダー
(4 ピン CIR1)
このヘッダーは、リモコン受光部
の接続に使用することができます。
ページ2, アイテム 25 を参照
フロントオーディオパネルコネクタ
(9 ピン HD_AUDIO1)
ページ2, アイテム 32 を参照 GND
PRESENCE#
MIC_RET
OUT_RET
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
このコネクタは、オーディオ機器
との便利な接続とコントロールを
可能にするフロンとオーディオパ
ネルのためのインターフェイスで
す。
1.
ハイディフィニションオーディオはジャックセンシングをサポー
トしますが、正しく機能するためにシャーシのパネルワイヤが
HAD をサポートする必要があります。このマニュアルとシャー
シのマニュアルの指示に従って、システムを取り付けてくださ
い。
2.
AC’97 オーディオパネルを使用する場合、次のように前面パ
ネルのオーディオヘッダに取り付けてください。
A.
Mic_IN (MIC) を MIC2_L に接続します。
B.
Audio_R (RIN) を OUT2_R に、Audio_L (LIN) を
OUT2_L に接続します。
C.
Ground (GND) を Ground (GND) に接続しま
す。
D.
MIC_RET と OUT_RET はオーディオパネル専用です。
AC’97 オーディオパネルに接続する必要はありません。
E.
フロントマイクを有効化するには。
Windows® XP / XP 64-bit OS の場合 :
“Mixer” ( ミキサー ) を選択し、続いて “Recorder” ( レコー
ダー ) を選択します。その後 “FrontMic” ( フロントマイク ) をク
リックします。
Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit OS の場合 :
Realtek コントロールパネルから “FrontMic” ( フロントマイ
ク ) タブを開きます。“Recording Volume”( 録音音量 ) を調
整します。
日本語
124
システムパネルコネクタ
(9 ピン PANEL1)
このコネクタは数種類のシステム
フロントパネルの機能を提供しま
ページ2, アイテム 23 を参照
す。
ASRock 970 Extreme3 R2.0 Motherboard
シャーシに付いている電源スイッチ、リセットスイッチ、システムステータ
スインジケータを下記のピン割り当て指示に従ってこのヘッダに接続します。
ケーブルを接続する前にピンの正負極性にご注意ください。
PWRBTN ( 電源スイッチ ):
前面パネルに付いている電源スイッチに接続します。電源スイッチによるシス
テム電源オフ方法を設定して変更することも可能です。
RESET ( リセットスイッヱ ):
シャーシの前面パネルに付いているリセットスイッチに接続します。コン
ピュータがフリーズし、正常な再起動をしない場合は、リセットスイッチを
押してコンピュータを再起動します。
PLED ( システム電源 LED):
シャーシの前面パネルに付いている電源ステータスインジケータに接続しま
す。LED は、システムが動作しているときに点灯します。LED はシステム
が S1 スリープ状態のときに点滅します。システムが S3 または S4 スリープ状
態になるか、電源オフ (S5) になると、LED は消灯します。
HDLED ( ハードドライブアクティビティ LED):
シャーシの前面パネルに付いているハードドライブアクティビティ LED に接続
します。LED は、ハードドライブがデータの読み込みまたは書き込み動作を
しているときに点灯します。
前面パネルのデザインはシャーシによって異なります。前面パネルモジュール
は、主に電源スイッチ、リセットスイッチ、電源 LED、ハードドライブア
クティビティ LED、スピーカーなどから構成されています。シャーシの前面
パネルモジュールをこのヘッダに接続する際は、ワイヤとピンの割り当てが正
しく対応していることを確認してください。
シャーシスピーカーヘッダ
(4 ピン SPEAKER1)
シャーシのスピーカーとこのヘッ
ダを接続してください。
ページ2, アイテム 24 を参照
シャーシ電源 LED をこのヘッダーに
接続し、システム電源ステータスを
示すようにしてください。LED はシ
ステムが動作中の際にオンになりま
す。S1 ステータスでは LED は点滅し
続けます。S3/S4 ステータス、または
S5 ステータス ( 電源オフ ) の場合、
LED は消灯します。
ページ2, アイテム 22 を参照 シャーシおよび電源ファンコネクタ
(4 ピン CHA_FAN1)
ページ2, アイテム 12 を参照
(3 ピン CHA_FAN2)
ページ2, アイテム 15 を参照
GND
+12V
CHA_FAN_SPEED
日本語
電源 LED ヘッダー
(3 ピン PLED1)
ファンケーブルをファンコネクタ
に接続し、黒いワイヤをアースピ
ンに合わせてください。CHA_
FAN1/2/3 ファン速度は、UEFI また
は AXTU を通して制御可能できま
す。
ASRock 970 Extreme3 R2.0 Motherboard
125
(3 ピン CHA_FAN3)
ページ2, アイテム 2 を参照
(3 ピン PWR_FAN1)
ページ2, アイテム 10 を参照
CPU ファンコネクタ
(4 ピン CPU_FAN1)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
ページ2, アイテム 6 を参照
このコネクタには CPU ファンケー
ブルを接続します。黒いコードは
アースピンに接続してください。
1 2 3 4
このマザーボードでは 4 ピン CPU ファン ( クワイエットファン ) がサポートされていますが、
ファン速度コントロール機能がない場合でも、3 ピン CPU ファンは正常に作動します。3
ピン CPU ファンをこのマザーボードの CPU ファンコネクタに接続しようとしている場合、
ピン 1-3 に接続してください。
接続されたピン 1-3
3 ピンファンのインストール
(3 ピン CPU_FAN2)
GND
+12V
CPU_FAN_SPEED
ページ2, アイテム 5 を参照
ATX パワーコネクタ
12
24
1
13
ATX 電源コネクタを接続します。
(24 ピン ATXPWR1) ページ2, アイテム 9 を参照
このマザーボードには 24 ピン ATX 電源コネクタが装備されており、
従来の 20 ピン ATX 電源装置を採用している場合でも作動します。
20 ピン ATX 電源を使用するには、ピン 1 およびピン 13 と共に電源
装置にプラグを差し込みます。
日本語
ATX 12V コネクタ
(8 ピン ATX12V1)
ページ2, アイテム 1 を参照
126
5
1
8
4
12
24
20 ピン ATX 電源装置の取り付け 1
13
このコネクタには CPU に Vcore 電
源を供給できるように、ATX 12V
プラグを備えたサワーサプライを
接続する必要があることに注意し
てください。接続に問題があると、電源
は正しく供給されません。
ASRock 970 Extreme3 R2.0 Motherboard
このマザーボードで 8-pin ATX 12V 電源コネクタが提供されたが、従来の 4-pin ATX 12V 電源でも動作できます。 4-pin ATX 電源を使用する場合、電源を Pin 1 と Pin 5 とともに差し込んでください。
5
1
4-Pin ATX 12V 電源の取り付け
8
4
この COM1 ヘッダは、シリアルポートモ
ジュールをサポートします。
ページ2, アイテム 30 を参照
シリアルポートヘッダ
(9 ピン COM1)
HDMI_SPDIF ヘッダ
HDMI_SPDIF ヘッダは、SPDIF
音声出力を HDMI VGA カードに提
供し、システムで HDMI デジタル
TV/ プロジェクタ /LCD デバイスに
接続できるようにします。HDMI
VGA カードの HDMI_SPDIF コネク
タを、このヘッダに接続してくださ
い。
(2- ピン HDMI_SPDIF1)
ページ2, アイテム 31 を参照
USB 3.0 ヘッダ
Vbus
(19 ピン USB3_2_3)
Vbus
ページ 2, アイテム 38 を参照
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
GND
I/O パネルには、デフォルトの 2 つの
USB 3.0 ポート以外に、このマザーボ
ードに 1 つの USB 3.0 ヘッダが搭載
されています。それぞれの USB 3.0
ヘッダは 2 つの USB 3.0 ポートをサ
ポートできます。
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
日本語
IntA_P3_SSRX-
ASRock 970 Extreme3 R2.0 Motherboard
127
2. BIOS 情報
BIOS セットアップユーティリティはマザーボードのフラッシュメモリに保存されています。コン
ピュータを起動させた後、POST(パワーオンセルフテスト)中に〈F2〉または <Del> を押し、
BIOS セットアップユーティリティに入ってください。押さない場合、POST はテストルーチンを
続けます。テストを実行した後に BIOS セットアップユーティリティに入りたい場合、POST 終
了後〈Ctrl〉+〈Alt〉+〈Delete〉を押すか、ケースのリセットスイッチを押してシステムを
再起動してください。BIOS セットアップユーティリティは、ユーザーフレンドリであることを目
指しています。これはメニュウ方式のプログラムです。スクロールさせることで様々なサブ
メニューを表示し、かつあらかじめ定義した選択肢から選択することが可能です。BIOS セッ
トアップの詳細な情報については、サポート CD 内のユーザーズマニュアル (PDF ファイル )
をごらんください。
3. ソフトウェア サポート CD 情報
このマザーボードは Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit /
VistaTM / VistaTM 64-bit / XP / XP 64-bit といった様々なマイクロソフト ウイン
ドウズ オペレーティングシステムをサポートします。マザーボードに付属しているサポート
CD はマザーボードの特徴を有効にするために必要なドライバやユーティリティを含んでい
ます。サポート CD を使用するには、CDROM ドライブに CD を挿入してください。AUTORUN
機能が有効な場合、自動的にメインメニュウが立ち上がります。AUTORUN 機能が無効な
場合、サポート CD 内の BIN フォルダにある ASSETUP.EXE をダブルクリックすることによ
り、メインメニュウが立ち上がります。
日本語
128
ASRock 970 Extreme3 R2.0 Motherboard
1. 主板簡介
謝謝你采用了華擎 970 Extreme3 R2.0 主板 , 本主板由華擎嚴格制造 , 質量可靠 ,
穩定性好 , 能夠獲得卓越的性能。本安裝指南介紹了安裝主板的步驟。更加詳細的主
板信息可參看驅動光盤的用戶手冊。
由于主板規格和 BIOS 軟件將不斷升級 , 本手冊之相關內容變更恕不另
行通知。請留意華擎网站上公布的升級版本。你也可以在華擎網站找
到最新的顯卡和 CPU 支持表。
華擎网址:http://www.asrock.com
如果您需要與此主板有關的技術支持 , 請參觀我們的網站以了解您使用機
種的規格信息。
www.asrock.com/support/index.asp
1.1 包裝盒內物品
華擎 970 Extreme3 R2.0 主板 (ATX 規格 )
華擎 970 Extreme3 R2.0 快速安裝指南
華擎 970 Extreme3 R2.0 支持光盤
兩條 Serial ATA(SATA) 數據線 ( 選配 )
一塊 I/O 擋板
ASRock提醒您 ...
®
簡體中文
為了在 Windows 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64bit 系統中取得更好的性能,建議您在BIOS中將Storage Configuration
(存儲配置)選項設成AHCI模式。關于BIOS設置程序,請參見支持光盤中
的“User Manual”以了解相詳細信息。
ASRock 970 Extreme3 R2.0 Motherboard
129
1.2
主板規格
架构
處理器
芯片組
系統內存
擴展插槽
音效
板載 LAN 功能
簡體中文
130
-
ATX 規格
全固態電容設計 (100% 日本原裝高品質高傳導固態電容 )
支持 Socket AM3+ 處理器
支持 Socket AM3 處理器 : AMD PhenomTM II X6 / X4 /
X3 / X2(920/940 除外 ) / Athlon II X4 / X3 / X2 / Sempron 處理器
- 八核心 CPU 就緒
- 支持 UCC (Unlock CPU Core)
- Digi 電源設計
- 4 + 1 電源相位設計
- 支持高達 140W 的 CPU
™
- 支持 AMD Cool ‘n’ Quiet 冷靜技術
- 支持 FSB 2400 MHz (4.8 GT/s)
- 支持異步超頻技術
- 支持 Hyper-Transport 3.0 (HT 3.0) 技術
- 北橋 : AMD 970
- 南橋 : AMD SB950
- 支持雙通道內存技術
- 配備 4 個 DDR3 DIMM 插槽
- 支持 DDR3 2100+( 超頻 )/1866( 超頻 )/1800( 超頻 )/1600
( 超頻 )/1333/1066/800 non-ECC、un-buffered 內存
- 系統最高支持 32GB 容量
- 2 x PCI Express 2.0 x16 插槽
(PCIE2: x16 模式 ; PCIE4: x4 模式 )
- 2 x PCI Express 2.0 x1 插槽
- 2 x PCI 插槽
- 支持 AMDTM Quad CrossFireXTM 和 CrossFireXTM
- 7.1 聲道高保真音頻 , 支持內容保護功能
(Realtek ALC892 音頻編解碼器 )
- 支持優質藍光音效
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- 支持网路喚醒(Wake-On-LAN)
- 支持網路線偵測功能
- 支持 Energy Efficient Ethernet 802.3az
- 支持 PXE
ASRock 970 Extreme3 R2.0 Motherboard
SATA3
USB 3.0
連接頭
BIOS
I/O 界面
- 1 個 PS/2 鼠標接口
- 1 個 PS/2 鍵盤接口
- 1 個同軸 SPDIF 輸出接口
- 1 個光纖 SPDIF 輸出接口
- 4 個可直接使用的 USB 2.0 接口
- 2 個可直接使用的 USB 3.0 接口
- 1 個 eSATA3 接口
- 1 個 RJ-45 局域网接口與 LED 指示燈 (ACT/LINK LED 和
SPEED LED)
- 高保真音頻插孔:側置喇叭 / 后置喇叭 / 中置喇叭 /
低音喇叭 / 音頻輸入 / 前置喇叭 / 麥克風
- 5 x SATA3 6.0Gb/s 連接頭,支持 RAID (RAID 0, RAID 1,
RAID 5 和 RAID 10), NCQ, AHCI 和熱插拔功能
- 2 x Etron EJ188H 的后置 USB 3.0 連接頭,支持 USB
1.1/2.0/3.0 到 5Gb/s
- 1 x Etron EJ188H 的前置 USB 3.0 連接頭 ( 支持 2 個 USB 3.0
接口 ),支持 USB 1.1/2.0/3.0 到 5Gb/s
- 5 x SATA3 6.0Gb/s 連接頭
- 1 x 紅外線模塊接頭
- 1 x 消費類紅外線模塊接頭
- 1 X 串行接口連接器
- 1 x HDMI_SPDIF 接頭
- 1 x 電源指示燈連接排針
- 2 x CPU 風扇接頭 (1 x 4 針 , 1 x 3 針 )
- 3 x 機箱風扇接頭 (1 x 4 針 , 2 x 3 針 )
- 1 x 電源風扇接頭 (3 針 )
- 24 針 ATX 電源接頭
- 8 針 12V 電源接頭
- 前置音頻面板接頭
- 2 x USB 2.0 接口 ( 可支持 4 個額外的 USB 2.0 接口 )
- 1 x USB 3.0 接針 ( 可支持 2 個額外的 USB 3.0 接口 )
- 32Mb AMI UEFI Legal BIOS, 支持 GUI
- 支持即插即用(Plug and Play,PnP)
- ACPI 1.1 電源管理
- 支持喚醒功能
- 支持 jumperfree 免跳線模式
- 支持 SMBIOS 2.3.1
- CPU, VCCM, NB, SB 電壓多功能調節器
ASRock 970 Extreme3 R2.0 Motherboard
簡體中文
Rear Panel I/O
( 后面板輸入 /
輸出接口 )
131
支持光盤
硬件監控器
操作系統
認證
- 驅動程序、工具軟件、殺毒軟件(試用版 )、CyberLink
MediaEspresso 6.5 試用版、Chrome 谷歌瀏覽器和工具欄
- CPU 溫度偵測
- 主板溫度偵測
- CPU/ 機箱 / 電源風扇轉速計
- CPU/ 機箱靜音風扇
- CPU/ 機箱風扇多速控制
- 電壓範圍:+12V, +5V, +3.3V, 核心電壓
®
®
- Microsoft Windows 8/8 64 位元 /7/7 64 位元 /VistaTM/
TM
Vista 64 位元 /XP/XP 64 位元适用于此主板
- FCC, CE, WHQL
- 支持 ErP/EuP( 需要同時使用支持 ErP/EuP 的電源供應器 )
* 請參閱華擎網站了解詳細的產品信息 : http://www.asrock.com
1.3
跳線設置
插圖所示的就是設置跳線的方法。當跳線
帽 放 置 在 針 腳 上 時 , 這 個 跳 線 就 是“ 短
接”。如果針腳上沒有放置跳線帽 , 這個
跳線就是“開路”。插圖顯示了一個 3 針
腳的跳線 , 當跳線帽放置在針腳 1 和針腳 2
之間時就是“短接”。
接腳
清除 CMOS
設定
(CLRCMOS1, 3 針腳跳線 )
( 見第 2 頁第 21 項 )
默認設置
清除 CMOS
簡體中文
注意:C L R C M O S1 允 許 您 清 除 C M O S 中 的 數 据。 如 要 清 除 并 將 系 統 參 數 恢 复 至 默 認
設置,請關閉計算机,然后從電源插座上拔掉電源線。等待 15 秒后,使用跳
線帽將 C L R C M O S1 上的插針 2 和插針 3 短接 5 秒。但是,請勿在更新 B I O S 后
立即清除 C M O S。如果需要在更新 B I O S 后立即清除 C M O S,必須在執行 C M O S
清除操作之前,先啟動然后關閉系統。請注意,只有取出 C M O S 電池,密碼、
日期、時間、用戶默認配置文件、1394 GUID 和 MAC 地址才會被清除。
132
ASRock 970 Extreme3 R2.0 Motherboard
1.4
板載接頭和接口
板載接頭和接口不是跳線。切勿將跳線帽放置在這些接頭和接口上。將
跳線帽放置在接頭和接口上將會導致主板的永久性損壞!
Serial ATA3 接口
(SATA3_1: 見第 2 頁第 17 項 )
SATA3_3
SATA3_1
SATA3_4
SATA3_2
(SATA3_2: 見第 2 頁第 18 項 )
(SATA3_3: 見第 2 頁第 16 項 )
(SATA3_4: 見第 2 頁第 19 項 )
SATA3_5
(SATA3_5: 見第 2 頁第 20 項 )
這裡有五組 Serial ATA3
(SATA3) 接口支持 Serial
(SATA) 數據線作為內部儲存
設置。目前 SATA3 界面理論 上可提供高達 6.0Gb/s 的數
據傳輸速率。
Serial ATA (SATA)
數據線
( 選配 )
SATA 數據線的任意一端均可連
接 SATA/SATAII/SATA3 硬盤或者
主板上的 SATA3 接口。
USB 2.0 擴展接頭
(9 針 USB_4_5)
( 見第 2 頁第 26 項 )
除了位於 I/O 面板的四個默
認 USB 2.0 接口之外,這款
主板有三組 USB 2.0 接針。
這組 USB 2.0 接針可以支持
兩個 USB 2.0 接口。
(9 針 USB_6_7)
( 見第 2 頁第 27 項 )
USB_PWR
P-9
P+9
GND
DUMMY
(9 針 USB_8_9)
( 見第 2 頁第 28 項 )
1
紅外線模塊接頭
(5 針 IR1)
( 見第 2 頁第 29 項 )
簡體中文
GND
P+8
P-8
USB_PWR
這個接頭支持一個選配的無
線發送和接受紅外線的
模塊。
ASRock 970 Extreme3 R2.0 Motherboard
133
消費類紅外線模塊接頭
(4 針 CIR1)
此接口可以連接遙控器。
( 見第 2 頁第 25 項 )
前置音頻面板接頭
GND
PRESENCE#
MIC_RET
OUT_RET
(9 針 HD_AUDIO1)
( 見第 2 頁第 32 項 )
可以方便連接音頻設備。
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. 高保真音頻 (High Definition Audio, HDA) 支持智能音頻接口檢測功能
(Jack Sensing), 但是機箱面板的連線必須支持 HDA 才能正常使用。請按我
們提供的手冊和機箱手冊上的使用說明安裝您的系統。
2. 如果您使用 AC’97 音頻面板 , 請按照下面的步驟將它安裝到前面板音頻接針 :
A. 將 Mic_IN(MIC) 連接到 MIC2_L。
B. 將 Audio_R(RIN) 連接到 OUT2_R, 將 Audio_L(LIN) 連接到
OUT2_L。
C. 將 Ground(GND) 連接到 Ground(GND)。
D. MIC_RET 和 OUT_RET 僅用于 HD 音頻面板。您不必將它們連接到
AC’97 音頻面板。
E. 開啟前置麥克風。
®
在 Windows XP / XP 64 位元操作系統中 :
選擇”Mixer”。選擇”Recorder”。接著點擊”FrontMic”。
®
在 Windows 8 / 8 64 位元 / 7 / 7 64 位元 / VistaTM / VistaTM 64
位元操作系統中 :
在 Realtek 控制面板中點擊”FrontMic”。調節”Recording Volume”。
系統面板接頭
(9 針 PANEL1)
這個接頭提供數個系統前面
板功能。
( 見第 2 頁第 23 項 )
簡體中文
134
根據下面的針腳說明連接機箱上的電源開關、重啟按鈕與系統狀態
指示燈到這個排針。根據之前請注意針腳的正負極。
PWRBTN( 電源開關 ):
連接機箱前面板的電源開關。您可以設置用電源鍵關閉系統的方式。
RESET( 重啟開關 ):
連接機箱前面板的重啟開關。當電腦死機且無法正常重新啟動時 , 可
按下重啟開關重新啟動電腦。
ASRock 970 Extreme3 R2.0 Motherboard
PLED( 系統電源指示燈 ):
連接機箱前面板的電源狀態指示燈。當系統運行時 , 此指示燈亮起。
當系統處于 S1 待機模式時 , 此指示燈保持閃爍。當系統處于 S3/S4 待
機模式或關機 (S5) 模式時 , 此指示燈熄滅。
HD LED( 硬盤活動指示燈 ):
連接機箱前面板的硬盤動作指示燈。當硬盤正在讀取或寫入數據時 ,
此指示燈亮起。
前面板設計因機箱不同而有差異。前面板模塊一般由電源開關、
重啟開關、電源指示燈、硬盤動作指示燈、喇叭等構成。將您的機
箱前面板連接到此排針時 , 請確認連接線與針腳上的說明相對應。
機箱喇叭接頭
(4 針 SPEAKER1)
請將機箱喇叭連接到這個接
頭。
( 見第 2 頁第 24 項 )
電源指示燈連接排針
(3 針 PLED1)
( 見第 2 頁第 22 項 )
請將機箱電源指示燈連接到
這一排針,以指示系統電源
狀態。當系統正在運行時,
LED 指示燈亮。在 S1 模式
下,LED 指示燈會不停閃
爍。在 S3/S4 或 S5 模式 ( 關
機 ) 下,LED 指示燈會熄滅。
機箱 , 電源風扇接頭
(4 針 CHA_FAN1)
( 見第 2 頁第 12 項 )
請將風扇連接線接到這個
接頭,並讓黑線與接地的針腳
相接。CHA_FAN1/2/3 風扇速度
可通過 UEFI 或 AXTU 來控制。
(3 針 CHA_FAN2)
( 見第 2 頁第 15 項 )
GND
+12V
CHA_FAN_SPEED
(3 針 CHA_FAN3)
( 見第 2 頁第 2 項 )
CPU 風扇接頭
(4 針 CPU_FAN1)
( 見第 2 頁第 6 項 )
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
簡體中文
(3 針 PWR_FAN1)
( 見第 2 頁第 10 項 )
請將 CPU 風扇連接線接到這個
接頭,並讓黑線與接地的針腳
相接。
1 2 3 4
ASRock 970 Extreme3 R2.0 Motherboard
135
雖然此主板支持 4-Pin CPU 風扇 (Quiet Fan, 靜音風扇 ), 但是沒有調速功能的
3-Pin CPU 風扇仍然可以在此主板上正常運行。如果您打算將 3-Pin CPU 風扇
連接到此主板的 CPU 風扇接口 , 請將它連接到 Pin 1-3。
Pin 1-3 連接
3-Pin 風扇的安裝
(3 針 CPU_FAN2)
( 見第 2 頁第 5 項 )
GND
+12V
CPU_FAN_SPEED
ATX 電源接頭
(24 針 ATXPWR1)
12
24
1
13
請將 ATX 電源供應器連接到這
個接頭。
( 見第 2 頁第 9 項 )
雖然此主板提供 24-pin ATX 電源接口 , 但是您仍然可以使用
傳統的 20-pin ATX 電源。為了使用 20-pin ATX 電源 , 請順著
Pin 1 和 Pin 13 插上電源接頭。
12
24
20-Pin ATX 電源安裝說明
1
13
ATX 12V 接頭
(8 針 ATX12V1)
5
1
( 見第 2 頁第 1 項 )
8
4
請將一個 ATX 12V 電源供應
器接到這個接頭。
雖然此主板提供 8-pin ATX 12V 電源接口 , 但是您仍然可以使用傳統的 4-pin
ATX 12V 電源。為了使用 4-pin ATX 12V 電源 , 請順著 Pin 1 和 Pin 5 插上電
5
1
源接頭。
4-Pin ATX 12V 電源安裝說明
8
簡體中文
串行接口連接器
(9 針 COM1)
這個 COM1 端口支持一個串行
接口的外設。
( 見第 2 頁第 30 項 )
136
4
ASRock 970 Extreme3 R2.0 Motherboard
HDMI_SPDIF 接頭
(2 針 HDMI_SPDIF1)
HDMI_SPDIF 接頭,提供 SPDIF
音頻輸出至 HDMI 顯卡,支持
( 見第 2 頁第 31 項 )
將電腦連接至帶 HDMI 的數字
電視 / 投影儀 / 液晶顯示器等
設備。請將 HDMI 顯卡的
HDMI_SPDIF 接口連接到這個
接頭。
USB 3.0 擴展接頭
(19 針 USB3_2_3)
( 見第 2 頁第 38 項 )
Vbus
Vbus
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P3_SSTX-
IntA_P2_SSTX-
IntA_P3_SSTX+
IntA_P2_SSTX+
GND
2.
IntA_P3_SSRX-
GND
除了位於 I/O 面板的兩個默認
USB 3.0 接口之外,這款主板有
一組 USB 3.0 接針。這組 USB 3.0
接針可以支持兩個 USB 3.0 接
口。
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
BIOS 信息
主板上的 Flash Memory 存儲了 BIOS 設置程序。請再啟動電腦進行開機自檢 (POST)
時按下 < F2> 或 < D e l > 鍵進入 B I O S 設置程序;此外,你也可以讓開機自檢 ( P O S T )
進行常規檢驗。如果你需要在開機自檢 ( P O S T ) 之后進入 B I O S 設置程序,請按下
<Ctrl>+<Alt>+<Delete> 鍵重新啟動電腦,或者按下系統面板上的重啟按鈕。有關
BIOS 設置的詳細信息,請查閱隨機支持光盤裡的用戶手冊 (PDF 文件 )。
3.
支持光盤信息
®
®
簡體中文
本主板支持各種微軟視窗操作系統:Microsoft Windows 8/8 64 位元 /7/7 64 位元
/VistaTM/VistaTM 64 位元 /XP/XP 64 位元。主板隨機支持光盤包含各種有助于提高主
板效能的必要驅動和實用程序。請將隨機支持光盤放入光驅裡,如果電腦的“自動運
行”功能已啟用,屏幕將會自動顯示主菜單。如果主菜單不能自動顯示,請查找支持
光盤內 BIN 文件夾下的“ASSETUP.EXE”,并雙擊它,即可調出主菜單。
ASRock 970 Extreme3 R2.0 Motherboard
137
電子信息產品污染控制標示
依據中國發布的「電子信息產品污染控制管理辦法」及 SJ/T 11364-2006「電子信息
產品污染控制標示要求」,電子信息產品應進行標示,藉以向消費者揭露產品中含有
的有毒有害物質或元素不致發生外洩或突變從而對環境造成污染或對人身、財產造成
嚴重損害的期限。依上述規定,您可于本產品之印刷電路板上看見圖一之標示。圖一
中之數字為產品之環保使用期限。由此可知此主板之環保使用期限為 10 年。
圖一
有毒有害物質或元素的名稱及含量說明
若您慾了解此產品的有毒有害物質或元素的名稱及含量說明,請參照以下表格及說
明。
有害物質或元素
部件名稱
鉛 (Pb) 鎘 (Cd) 汞 (Hg) 六价鉻 (Cr(VI)) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE)
印刷電路板
X
O
O
O
O
O
及電子組件
外部信號連
X
O
O
O
O
O
接頭及線材
O: 表示該有毒有害物質在該部件所有均質材料中的含量均在 SJ/T 11363-2006 標準規定
的限量要求以下。
X: 表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2006 標準
規定的限量要求,然該部件仍符合歐盟指令 2002/95/EC 的規範。
備註 : 此產品所標示之環保使用年限,系指在一般正常使用狀況下。
簡體中文
138
ASRock 970 Extreme3 R2.0 Motherboard
1. 主機板簡介
謝謝你採用了華擎 970 Extreme3 R2.0 主機板 , 本主機板由華擎嚴格製造 , 品質可靠 ,
穩定性好 , 能夠獲得卓越的性能。此快速安裝指南包括了主機板介紹和分步驟安裝指
導。您可以查看支持光碟裡的使用手冊了解更詳細的資料。
由於主機板規格和 BIOS 軟體將不斷更新 , 本手冊之相關內容變更恕不另
行通知。請留意華擎網站上公布的更新版本。你也可以在華擎網站找到最
新的顯示卡和 CPU 支援列表。
華擎網址:http://www.asrock.com
如果您需要與此主機板有關的技術支援 , 請參觀我們的網站以了解您使用
機種的規格訊息。
www.asrock.com/support/index.asp
1.1 包裝盒內物品
華擎 970 Extreme3 R2.0 主機板 (ATX 規格 )
華擎 970 Extreme3 R2.0 快速安裝指南
華擎 970 Extreme3 R2.0 支援光碟
兩條 Serial ATA(SATA) 數據線 ( 選配 )
一塊 I/O 擋板
ASRock提醒您...
繁體中文
若要在Windows® 8 / 8 64位元 / 7 / 7 64位元 / VistaTM / VistaTM 64位
元中發揮更好的效能,建議您將儲存裝置組態中的B I O S選項設為A H C I模
式。有關BIOS設定的詳細資訊,請參閱支援光碟中的「使用者手冊」。
ASRock 970 Extreme3 R2.0 Motherboard
139
1.2
主機板規格
架構
處理器
-
晶片組
系統記憶體
擴充插槽
音效
網路功能
繁體中文
140
-
ATX 規格
全固態電容設計 (100% 日本原裝高品質高傳導固態電容 )
支援 Socket AM3+ 處理器
支援 Socket AM3 處理器 : AMD PhenomTM II X6 / X4 /
X3 / X2(920 / 940 除外 ) / Athlon II X4 / X3 / X2 / Sempron 處理器
八核心 CPU 就緒
支援 UCC (Unlock CPU Core)
Digi 電源設計
4 + 1 電源相位設計
支援高達 140W 的 CPU
支援 AMD Cool ‘n’ Quiet 冷靜技術
支援 FSB 2400 MHz (4.8 GT/s)
支援非同步超頻技術
支援 Hyper-Transport 3.0 (HT 3.0) 技術
北橋 : AMD 970
南橋 : AMD SB950
支援雙通道記憶體技術
4 個 DDR3 DIMM 插槽
支援 DDR3 2100+( 超頻 )/1866( 超頻 )/1800( 超頻 )/1600( 超
頻 )/1333/1066/800 non-ECC、un-buffered 記憶體
系統最高支援 32GB 容量
2 x PCI Express 2.0 x16 插槽
(PCIE2: x16 模式 ; PCIE4: x4 模式 )
2 x PCI Express 2.0 x1 插槽
2 x PCI 插槽
支援 AMDTM Quad CrossFireXTM 和 CrossFireXTM
7.1 聲道高清晰音效 , 支援內容保護功能
(Realtek ALC892 音效編解碼器 )
支援高級藍光音效
PCIE x1 Gigabit LAN 10/100/1000 Mb/s
Realtek RTL8111E
支援網路喚醒(Wake-On-LAN)
支援網路線偵測功能
支援 Energy Efficient Ethernet 802.3az
支援預先開機執行環境(PXE)
ASRock 970 Extreme3 R2.0 Motherboard
Rear Panel I/O
I/O 界面
- 1 個 PS/2 滑鼠接口
( 後背板輸入 /
輸出接口 )
-
SATA3
-
USB 3.0
-
接頭
BIOS
-
ASRock 970 Extreme3 R2.0 Motherboard
繁體中文
1 個 PS/2 鍵盤接口
1 個同軸 SPDIF 輸出接口
1 個光纖 SPDIF 輸出接口
4 個可直接使用的 USB 2.0 接口
2 個可直接使用的 USB 3.0 接口
1 個 eSATA3 接口
1 個 RJ-45 區域網接口與 LED 指示燈 (ACT/LINK LED 和
SPEED LED)
高清晰音效插孔:側置喇叭 / 後置喇叭 / 中置喇叭 /
低音喇叭 / 音效輸入 / 前置喇叭 / 麥克風
5 x SATA3 6.0Gb/s 接頭,支援 RAID (RAID 0, RAID 1,
RAID 5 和 RAID 10), NCQ, AHCI 和熱插拔功能
2 x Etron EJ188H 的後置 USB 3.0 接頭,支援 USB 1.1/2.0/3.0
到 5Gb/s
1 x Etron EJ188H 的前置 USB 3.0 接頭 ( 支援 2 個 USB 3.0
接頭 ),支援 USB 1.1/2.0/3.0 到 5Gb/s
5 x SATA3 6.0Gb/s 接頭
1 x 紅外線模組接頭
1 x 消費性紅外線模組插座
1 X 序列埠
1 x HDMI_SPDIF 接頭
1 x 電源指示燈接頭
2 x CPU 風扇接頭 (1 x 4 針 , 1 x 3 針 )
3 x 機箱風扇接頭 (1 x 4 針 , 2 x 3 針 )
1 x 電源風扇接頭 (3 針 )
24 針 ATX 電源接頭
8 針 12V 電源接頭
前置音效接頭
3 x USB 2.0 接口 ( 可支援 6 個額外的 USB 2.0 接口 )
1 x USB 3.0 接頭 ( 可支援 2 個額外的 USB 3.0 接口 )
32Mb AMI UEFI Legal BIOS ( 支援 GUI)
支援即插即用(Plug and Play,PnP)
ACPI 1.1 電源管理
支援喚醒功能
支援 jumperfree 免跳線模式
支援 SMBIOS 2.3.1
CPU,VCCM,NB,SB 電壓多功能調節器
141
支援光碟
硬體監控器
操作系統
認證
- 驅動程式、工具軟體、防毒軟體(試用版本 )、CyberLink
MediaEspresso 6.5 試用版、Google Chrome Browser 和
Toolbar
- CPU 溫度偵測
- 主板溫度偵測
- CPU/ 機箱 / 電源風扇轉速計
- CPU/ 機箱靜音風扇
- CPU/ 機箱風扇多速控制
- 電壓範圍:+12V, +5V, +3.3V, 核心電壓
- Microsoft® Windows® 8/8 64 位元 /7/7 64 位元 /VistaTM/
VistaTM 64 位元 /XP/XP 64 位元
- FCC, CE, WHQL
- 支援 ErP/EuP( 需要同時使用支援 ErP/EuP 的電源供應器 )
* 請參閱華擎網站了解詳細的產品訊息 : http://www.asrock.com
1.3
跳線設置
插圖所示的就是設置跳線的方法。當跳線
帽 放 置 在 針 腳 上 時 , 這 個 跳 線 就 是“ 短
接”。如果針腳上沒有放置跳線帽 , 這個
跳線就是“開路”。插圖顯示了一個 3 針
腳的跳線 , 當跳線帽放置在針腳 1 和針腳 2
之間時就是“短接”。
接腳
清除 CMOS
設定
(CLRCMOS1, 3 針腳跳線 )
( 見第 2 頁第 21 項 )
默認設置
清除 CMOS
繁體中文
註:
C L R C M O S1 可供您清除 C M O S 中的資料。若要清除及重設系統參數並恢復為預設設
定,請先關閉電腦電源,並從電源插座中拔下電源線,等待 15 秒鐘之後,使用跳
線帽使 CLRCMOS1 的 pin2 及 pin3 短路 5 秒的時間。但請勿於更新 BIOS 後立即清除
CMOS。如需於更新 BIOS 後立即清除 CMOS,您必須先開機再關機,然後再執行 CMOS
清除操作。請注意,只有在移除 C M O S 電池的情況下,密碼、日期、時間、使用者
預設設定檔、1394 GUID 及 MAC 位址才會清除。
142
ASRock 970 Extreme3 R2.0 Motherboard
1.4
接頭
此類接頭是不用跳線帽連接的,請不要用跳線帽短接這些接頭。
跳線帽不正確的放置將會導致主機板的永久性損壞 !
接頭
Serial ATA3 接口
圖示
(SATA3_5: 見第 2 頁第 20 項 )
說明
這裡有五組 Serial ATA3
(SATA3) 接口支援 SATA 數據
線作為內部儲存設置。
目前 SATA3 界面理論上
可提供高達 6.0Gb/s 的數據
傳輸速率。
Serial ATA (SATA)
數據線
( 選配 )
SATA 數據線的任意一端均可
連接 SATA/SATAII/SATA3 硬
碟或者主機板上的 SATA3 接口。
USB 2.0 擴充接頭
(9 針 USB_4_5)
( 見第 2 頁第 26 項 )
除了位於 I/O 面板的四個
USB 2.0 接口之外,這款
主機板有三組 USB 2.0 接
針。每組 USB 2.0 接針可以
支援兩個 USB 2.0 接口。
(SATA3_1: 見第 2 頁第 17 項 )
SATA3_3
SATA3_1
SATA3_4
SATA3_2
(SATA3_2: 見第 2 頁第 18 項 )
(SATA3_3: 見第 2 頁第 16 項 )
(SATA3_4: 見第 2 頁第 19 項 ) SATA3_5
(9 針 USB_6_7)
( 見第 2 頁第 27 項 )
(9 針 USB_8_9)
( 見第 2 頁第 28 項 )
USB_PWR
P-9
P+9
GND
DUMMY
1
紅外線模組接頭
(5 針 IR1)
( 見第 2 頁第 29 項 )
繁體中文
GND
P+8
P-8
USB_PWR
這個接頭支援一個選配的模
組 , 可用來無線傳輸和接收紅
外線。
ASRock 970 Extreme3 R2.0 Motherboard
143
消費性紅外線模組插座
(4 針 CIR1)
此插座可用於連接遙控器。
( 見第 2 頁第 25 項 )
前置音效接頭
GND
PRESENCE#
MIC_RET
OUT_RET
(9 針 HD_AUDIO1)
( 見第 2 頁第 32 項 )
可以方便連接音效設備。
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. 高清晰音效 (High Definition Audio, HDA) 支援智能音效接口檢測功能
(Jack Sensing), 但是機箱面板的連線必須支持 HDA 才能正常使用。請按我
們提供的手冊和機箱手冊上的使用說明安裝您的系統。
2. 如果您使用 AC’97 音效面板 , 請按照下面的步驟將它安裝到前面板音效接針 :
A. 將 Mic_IN(MIC) 連接到 MIC2_L。
B. 將 Audio_R(RIN) 連接到 OUT2_R, 將 Audio_L(LIN) 連接到
OUT2_L。
C. 將 Ground(GND) 連接到 Ground(GND)。
D. MIC_RET 和 OUT_RET 僅用於 HD 音效面板。您不必將它們連接到
AC’97 音效面板。
E. 開啟前置麥克風。
在 Windows® XP / XP 64 位元作業系統中 :
選擇”Mixer”。選擇”Recorder”。接著點選”FrontMic”。
在 Windows® 8 / 8 64 位元 / 7 / 7 64 位元 / VistaTM / VistaTM 64
位元作業系統中 :
在 Realtek 控制面板中點選”FrontMic”。調整”Recording Volume”。
系統面板接頭
(9 針 PANEL1)
可接各種不同燈,電源開關及
重啟鍵等各種連線。
( 見第 2 頁第 23 項 )
繁體中文
144
請根據下面的腳位說明連接機箱上的電源開關、重開按鈕與系統狀
態指示燈到這個接頭。請先注意針腳的正負極。
PWRBTN( 電源開關 ):
連接機箱前面板的電源開關。您可以設定用電源鍵關閉系統的方式。
RESET( 重開開關 ):
連接機箱前面板的重開開關。當電腦當機且無法正常重新啟動時 , 可
按下重開開關重新啟動電腦。
ASRock 970 Extreme3 R2.0 Motherboard
PLED( 系統電源指示燈 ):
連接機箱前面板的電源狀態指示燈。當系統運行時 , 此指示燈亮起。
當系統處於 S1 待命模式時 , 此指示燈保持閃爍。當系統處於 S3/S4 待
命模式或關機 (S5) 模式時 , 此指示燈熄滅。
HD LED( 硬碟活動指示燈 ):
連接機箱前面板的硬碟動作指示燈。當硬碟正在讀取或寫入數據時 ,
此指示燈亮起。
前面板設計因機箱不同而有差異。前面板模組一般由電源開關、
重開開關、電源指示燈、硬碟活動指示燈、喇叭等構成。將您的機
箱前面板連接到此接頭時 , 請確認連接線與針腳上的說明相對應。
機箱喇叭接頭
(4 針 SPEAKER1)
請將機箱喇叭連接到這個接
頭。
( 見第 2 頁第 24 項 )
電源指示燈接頭
(3 針 PLED1)
( 見第 2 頁第 22 項 )
請將機箱電源指示燈連接到
此接頭,以指示系統電源狀
態。當系統正在運行時,
LED 指示燈亮。在 S1 模式
下,LED 指示燈會不停閃
爍。在 S3/S4 或 S5 模式 ( 關
機 ) 下,LED 指示燈會熄滅。
機箱 , 電源風扇接頭
(4 針 CHA_FAN1)
( 見第 2 頁第 12 項 )
請將風扇連接線接到這個接
頭, 並 讓 黑 線 與 接 地 的 針 腳
相接。CHA_FAN1/2/3 可由 UEFI
或 AXTU 設定。
(3 針 CHA_FAN2)
( 見第 2 頁第 15 項 )
GND
+12V
CHA_FAN_SPEED
(3 針 CHA_FAN3)
( 見第 2 頁第 2 項 )
CPU 風扇接頭
(4 針 CPU_FAN1)
( 見第 2 頁第 6 項 )
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
繁體中文
(3 針 PWR_FAN1)
( 見第 2 頁第 10 項 )
請將 CPU 風扇連接線接到這個
接頭,並讓黑線與接地的針腳
相接。
1 2 3 4
ASRock 970 Extreme3 R2.0 Motherboard
145
雖然此主板支持 4-Pin CPU 風扇 (Quiet Fan, 靜音風扇 ), 但是沒有調速功能的
3-Pin CPU 風扇仍然可以在此主板上正常運行。如果您打算將 3-Pin CPU 風扇
連接到此主板的 CPU 風扇接口 , 請將它連接到 Pin 1-3。
Pin 1-3 連接
3-Pin 風扇的安裝
(3 針 CPU_FAN2)
( 見第 2 頁第 5 項 )
GND
+12V
CPU_FAN_SPEED
ATX 電源接頭
(24 針 ATXPWR1)
12
24
1
13
請將 ATX 電源供應器連接到這
個接頭。
( 見第 2 頁第 9 項 )
雖然此主機板提供 24-pin ATX 電源接口 , 但是您仍然可以使
用傳統的 20-pin ATX 電源。為了使用 20-pin ATX 電源 , 請順
著 Pin 1 和 Pin 13 插上電源接頭。
20-Pin ATX 電源安裝說明
ATX 12V 電源接口
(8 針 ATX12V1)
( 見第 2 頁第 1 項 )
5
1
8
4
繁體中文
(9 針 COM1)
1
13
雖然此主機板提供 8-pin ATX 12V 電源接口 , 但是您仍然可以使用傳統的
5
1
4-pin ATX 12V 電源。為了使用 4-pin ATX 12V 電源 , 請
順著 Pin 1 和 Pin 5 插上電源接頭。
8
4
這個序列埠 COM1 支援一個序
列埠的裝置。
( 見第 2 頁第 30 項 )
146
24
請注意,必需將帶有 ATX 12V
插頭的電源供應器連接到這個
插座,這樣就可以提供充足的
電力。如果不這樣做,就會導
致供電故障。
4-Pin ATX 12V 電源安裝說明
序列埠
12
ASRock 970 Extreme3 R2.0 Motherboard
HDMI_SPDIF 接頭
(2 針 HDMI_SPDIF1)
HDMI_SPDIF 接頭,提供 SPDIF
音 效 輸 出 至 H D M I 顯 示 卡, 支
( 見第 2 頁第 31 項 )
援將電腦連接至帶 HDMI 的數
位電視 / 投影機 / 液晶銀幕等
設備。請將 HDMI 顯示卡的
HDMI_SPDIF 接口連接到這個
接頭。
USB 3.0 擴充接頭
(19 針 USB3_2_3)
( 見第 2 頁第 38 項 )
Vbus
Vbus
IntA_P3_SSRX-
IntA_P2_SSRX-
IntA_P3_SSRX+
IntA_P2_SSRX+
GND
GND
IntA_P2_SSTXIntA_P2_SSTX+
GND
IntA_P3_SSTXIntA_P3_SSTX+
GND
除了位於 I/O 面板的兩個 USB
3.0 接口之外,這款主機板有一
組 USB 3.0 接針。這組 USB 3.0
接針可以支援兩個 USB 3.0 接
口。
IntA_P3_D-
IntA_P2_D-
IntA_P3_D+
IntA_P2_D+
DUMMY
2. BIOS 訊息
主板上的 Flash Memory 晶片存儲了 BIOS 設置程序。啟動系統,在系統開機自檢 (POST)
的過程中按下 <F2> 或 <Del> 鍵,就可進入 BIOS 設置程序,否則將繼續進行開機自檢
之常規檢驗。如果需要在開機自檢後進入 BIOS 設置程序,請按下 <Ctl> + <Alt> +
<Delete> 鍵重新啟動電腦,或者按下系統面板上的重開按鈕。功能設置程序儲存有主
板自身的和連接在其上的設備的缺省和設定的參數。這些訊息用於在啟動系統和系統
運行需要時,測試和初始化元件。有關 B I O S 設置的詳細訊息,請查閱隨機支援光碟
裡的使用手冊 (PDF 文件 )。
3. 支援光碟訊息
本主板支援各種微軟 Windows® 操作系統:Microsoft® Windows® 8/8 64 位元 /7/7
ASRock 970 Extreme3 R2.0 Motherboard
繁體中文
64 位元 /VistaTM/VistaTM 64 位元 /XP/XP 64 位元。主板附帶的支援光碟包含各種有助
於提高主板效能的必要驅動和實用程式。請將隨機支援光碟放入光碟機裡,如果系統
的“自動運行”功能已啟用,銀幕將會自動顯示主菜單。如果主菜單不能自動顯示,
請查閱支援光碟內 BIN 文件夾下的 ASSETUP.EXE 文件並雙點它,即可調出主菜單。
147
1. Penjelasan
Terimakasih untuk membeli papan induk penghasilan kontrol kualitas keras terusmenerus ASRock’s yang dapat dipercaya. Dia dapat menyajikan pertunjukan baik
dengan bentuknya sesuai dengan janji kualitas dan ketahanan ASRock’s.
Buku Pedoman Instalasi Cepat ini mengandung perkenalan papan induk dan instalasi langkah-demi-langkah. Informasi lebih terperinci tentang papan induk ini dapat
dilihat dalam buku tangan pemakai dalam Support CD.
Karena spesifikasi papan induk dan software BIOS barangkali dapat diperbarui, isi dalam buku pedoman ini akan mengikuti perubahan tanpa peringatan. Dalam kondisi terjadinya modifikasi buku pedoman ini, versi baru akan diperlihatkan dalam website ASRock tanpa peringatan lebih. Anda dapat mendapatkan kartu-
kartu yang paling baru dan daftar bantuan CPU pada website ASRock.
Website ASRock http://www.asrock.com
1.1 Isi Paket
Papan Induk 970 Extreme3 R2.0 ASRock (Faktor Form ATX)
Pemimpin Instalasi Cepat 970 Extreme3 R2.0 ASRock
Support CD 970 Extreme3 R2.0 ASRock
2 x Kabel satu serial Data ATA (SATA) (bebas-pilih)
1 x Satu Pelindung I/O
ASRock Mengingatkan...
Untuk mendapatkan performa lebih baik di Windows® 8 / 8 64-bit / 7
/ 7 64-bit / VistaTM / VistaTM 64-bit, sebaiknya atur pilihan BIOS dalam
Storage Configuration (Konfigurasi Penyimpanan) ke mode AHCI. Untuk
konfigurasi BIOS, lihat “Panduan Pengguna” dalam CD dukungan kami
untuk informasi rinci.
Bahasa Indonesia
148
ASRock 970 Extreme3 R2.0 Motherboard
Spesifikasi
Podium
CPU
Grup Chip
Ingatan Alur Ekspansi
Audio
LAN
- Faktor Form ATX
- Desain All Solid Capacitor (100% Kapasitor Polimer
Konduktif buatan Jepang berkualitas tinggi)
- Stopkontak AM3+
- Stopkontak AM3 untuk AMD PhenomTM II X6 / X4 / X3 / X2
(kecuali 920 / 940) / Athlon II X4 / X3 / X2 / Sempron
processor
- Dukungan CPUT Delapan Inti
- Mendukung fitur UCC (Unlock CPU Core)
- Digi Power Desain
- Desain Daya 4 + 1 Fase
- Mendukung CPU hingga 140 W
- Dapat digunakan AM’s Cool ‘n’ QuietTM Technology
- FSB 2400 MHz (4.8 GT/s)
- Menggunakan Teknologi Untied Overclocking
- Dapat digunakan Hyper-Transport 3.0 (HT 3.0) Technology
- Jembatanutara: AMD 970
- Jembatanselatan: AMD SB950
- Teknologi ingatan DDR3 dwisaluran
- 4 x Alur DDR3 DIMM
- Menggunakan DDR3 2100+(OC)/1866(OC)/1800(OC)/
1600(OC)/1333/1066/800
- Kapasitas paling banyak: 32GB
- 2 x PCI Express 2.0 x16 slot
(PCIE2: mode x16; PCIE4: mode x4)
- 2 x PCI Express 2.0 x1 slot
- 2 x Alur PCI
- Mendukung AMDTM Quad CrossFireXTM dan CrossFireXTM
- 7.1 CH HD Audio dengan Content Protection
(Realtek ALC892 Audio Codec)
- Menggunakan Premium Blu-ray audio
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Menggunakan Wake-On-LAN
- Mendukung Deteksi Kabel LAN
- Mendukung Energy Efficient Ethernet 802.3az
- Mendukung PXE
ASRock 970 Extreme3 R2.0 Motherboard
Bahasa Indonesia
1.2
149
Papan Belakang I/O
I/O Panel
- 1 x Port Mouse PS/2
- 1 x Port Keyboard PS/2
- 1 x Port Keluaran Coaxial SPDIF
- 1 x Port Keluaran Optical SPDIF
- 4 x Port USB 2.0 siap-dipakai
- 2 x Port USB 3.0 siap-dipakai
- 1 x Port eSATA3
- 1 x RJ-45 LAN Port LED (ACT/LINK LED dan SPEED LED)
- HD Audio Jack: Penyuara Belakang/Pusat/Bass/Line in/
Penyuara Depan/mikropon
- 5 x penghubung SATA3 6.0Gb/s, dapat digunakan
RAID (RAID 0, RAID 1, RAID 5 dan RAID 10), NCQ, AHCI
dan fungsi fungsi “Hot Plug”
- 2 x Port Belakang USB 3.0 dari Etron EJ188H, mendukung
USB 1.1/2.0/3.0 hingga 5Gb/s
- 1 x Port Depan USB 3.0 dari Etron EJ188H (menggunakan
2 port USB 3.0), mendukung USB 1.1/2.0/3.0 hingga 5Gb/s
- 5 x penghubung SATA3 6.0Gb/s
- 1 x header IR
- 1 x header CIR
- 1 x port header COM
- 1 x HDMI_SPDIF header
Ciri-ciri BIOS
- 1 x header power LED
- 2 x Penghubung KIPAS CPU (1 x 4 pin, 1 x 3 pin)
- 3 x Penghubung KIPAS casis (1 x 4 pin, 2 x 3 pin)
- 1 x Penghubung KIPAS Power (3 pin)
- Penghubung power 24 pin ATX
- Penghubung power 8 pin 12V
- Penghubung audio panel dapan
- 3 x USB 2.0 header (menggunakan 6 port USB 2.0)
- 1 x USB 3.0 header (menggunakan 2 port USB 3.0)
- 32Mb AMI Legal BIOS
- AMI UEFI Legal BIOS dengan dukungan GUI
- Menggunakan “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Menggunakan jumperfree
- Penyokong AMBIOS 2.3.1
- Penyesuaian berbagai tegangan CPU, VCCM, NB, SB
SATA3
USB 3.0
Penghubung
Bahasa Indonesia
150
ASRock 970 Extreme3 R2.0 Motherboard
Sokongan CD
- Penggerak, kegunaan, Software AntiVirus (Versi Cobaan),
CyberLink MediaEspresso 6.5 Trial, Google Chrome
Penjaga Hardware OS
Sertifikasi Browser dan Toolbar
- Perasa Suhu CPU
- Perasa Suhu Casis
- Pengukur Kipas CPU/casis/Power
- Kipas diam CPU/Casis
- Kontrol Multi-Kecepatan Kipas CPU/casis
- Penjagaan voltasi: +12V, +5V, +3.3V, Vcore
- dapat digunakan Microsoft® Windows® 8 / 8 64-bit / 7 / 7
64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit
- FCC, CE, WHQL
- ErP/EuP Ready (memerlukan catu daya ErP/EuP ready)
Bahasa Indonesia
* Untuk informasi rinci, silakan kunjungi website kami: http://www.asrock.com
ASRock 970 Extreme3 R2.0 Motherboard
151
Installing OS on a HDD Larger Than 2TB
This motherboard is adopting UEFI BIOS that allows Windows® OS to be installed
on a large size HDD (>2TB). Please follow below procedure to install the operating
system.
1. Please make sure to use Windows® VistaTM 64-bit (with SP1 or above),
Windows® 7 64-bit or Windows® 8 64-bit.
2. Press <F2> or <Delete> at system POST. Set AHCI Mode in UEFI Setup Utility >
Advanced > Storage Configuration > SATA Mode.
3. Choose the item “UEFI:xxx“ to boot in UEFI Setup Utility > Boot > Boot Option #1.
(“xxx” is the device which contains your Windows® installation files. Normally it is an optical drive.) You can also press <F11> to launch boot menu at system POST
and choose the item “UEFI:xxx“ to boot.
4. Start Windows® installation.
English
152
ASRock 970 Extreme3 R2.0 Motherboard
Installing OS on a HDD Larger Than 2TB in RAID Mode
This motherboard is adopting UEFI BIOS that allows Windows® OS to be installed
on a large size HDD (>2TB). Please follow below procedure to install the operating
system.
1. Please make sure to use Windows® VistaTM 64-bit (with SP1 or above),
Windows® 7 64-bit or Windows® 8 64-bit.
2. Press <F2> or <Delete> at system POST. Set RAID Mode in UEFI Setup Utility >
Advanced > Storage Configuration > SATA Mode.
3. Choose onboard RAID 3TB+ unlocker > UEFI Mode For GPT partition. Press
<F10> to save the change and exit.
4. Press <F11> to enter Boot Manual. Choose UEFI : Built - in EFI Shell.
5. Key in drvcfg, for example you will see below:
Drv[4E] Ctrl[B5] Lang[eng]
English
6. Key in dh [Drv number], for example: key in dh 4E.
ASRock 970 Extreme3 R2.0 Motherboard
153
7. And then key in drvcfg –s [Drv number] [Ctrl number] to enter Raid Utility.
For example: key in drvcfg –s 4E B5.
8. Choose Logical Drive Main Menu to set up Raid Drive.
9. Choose Logical Drive Create Menu to create a Raid Drive.
10. Choose Usable Physical Drive List to select Raid HDD.
English
154
ASRock 970 Extreme3 R2.0 Motherboard
11. Press Space on keyboard to toggle checkbox.
12. Choose Ld Size setting, and key in the Raid size.
13. After set up Raid size, please click Start to Create.
English
14. Press <F10> to exit Utility.
15. During reboot, please press <F11> to enter Boot Manual. Choose UEFI: SCSI
CD/DVD Drive.
* This option only shows on Windows® 8 64-bit, 7 64-bit and VistaTM 64-bit OS.
ASRock 970 Extreme3 R2.0 Motherboard
155
16. Follow Windows® Installation Guide to install OS.
If you install Windows® 8 64-bit / 7 64-bit / VistaTM 64-bit in a large hard
disk (ex. Disk volume > 2TB), it may take more time to boot into Windows®
or install driver/utilities. If you encounter this problem, you will need to
following instructions to fix this problem.
Windows® VistaTM 64-bit:
Microsoft ® does not provide hotfix for this problem. Below steps are
Microsoft® suggested solution:
A. Disable System Restore.
a. Type “systempropertiesprotection” in the Start Menu. Then press "Enter".
b. De-select Local Disks for System Restore. Then Click “Turn System
Restore Off” to confirm. Then Press “Ok”.
English
156
ASRock 970 Extreme3 R2.0 Motherboard
B. Disable “Volume Shadow Copy” service.
a. Type “computer management” in the Start Menu, then press “Enter”.
b. Go to “Services and Applications>Services”; Then double click “Volume
Shadow Copy”.
English
c. Set “Startup type” to “Disable” then Click “OK”.
ASRock 970 Extreme3 R2.0 Motherboard
157
C. Reboot your system.
D. After reboot, please start to install motherboard drivers and utilities.
Windows® 8 64-bit / 7 64-bit:
A. Please request the hotfix KB2505454 thru this link:
http://support.microsoft.com/kb/2505454/
B. After installing Windows® 8 64-bit / 7 64-bit, install the hotfix kb2505454.
(This may take long time; >30 mins.)
C. Reboot your system. (It may take about 5 mins to boot.)
D. The Windows® will install this hotfix then reboot by itself.
E. Please start to install motherboard drivers and utilities.
17. Finish.
English
158
ASRock 970 Extreme3 R2.0 Motherboard
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising