product catalog

product catalog
PRODUCT CATALOG
Quality Products for
Air Conditioning,
Refrigeration & Heating
Table of Contents
Total System Protection
1-3
Coil Cleaners and Sprayers
4-10
Indoor Air Quality
11-14
Gas Leak Detectors
15
Refrigeration Oil & Vacuum Pump Oil
16-17
Aerosol Products
18-20
Specialty Products
21-22
Insulation Products
23
Glycol & Closed Systems
24-25
Water Treatment & Plumbing Products
26-30
Water Filtration Maintenance
31
Water Filtration
32-33
Nu-Plus by Everpure
34-39
Training Classes
READY
SET
40
Compatible with All Refrigerants & Oils
Easiest to Install
SEAL!
Permanent Seal
Takes seconds to inject.
No injection hose or caulk gun needed.
Concentrated formula means
less material in the system.
Total System Protection
Total System Protection
The Next Generation of Refrigerant Leak Sealant
EasySeal® Direct Inject
EasySeal Direct Inject is a new generation of sealants. Its innovative injection method
makes it easier to install than other sealants. With this new injection system, pumping
down the unit is a thing of the past. EasySeal Direct Inject works with all refrigerants
and oils. Concentrated formula means less material in system. It is perfect for split
systems, heat pumps, microchannel coils, packaged units, and mini splits. EasySeal
Direct Inject is formulated to not plug cap tubes or expansion valves.
EasySeal Direct Inject
EasySeal Direct Inject bulk 6-pack
EasySeal-SS Direct Inject
4050-08
4050-07
4050-05
A/C EasySeal®
A/C EasySeal prevents and seals refrigerant leaks in residential and light commercial ACR systems. It is perfect for those hard-to-find
and expensive-to-fix leaks and works with all refrigerants (except ammonia). It is easily installed with the reusable piercing valve and hose.
A/C EasySeal circulates with the system’s refrigerant, and if a leak should occur, it will quickly and permanently seal the leak and prevent the
system from losing refrigerant and shutting down.
A/C EasySeal
A/C EasySeal-SS
“2+1” Display Pack
A/C EasySeal-XL
A/C Piercing Valve and Hose
3 ounce pressurized can - treats 1.5 to 5 ton systems
1.25 ounce pressurized can - treats fractional to 1.5 ton systems
2 cans of A/C EasySeal and an A/C Piercing Valve and Hose
Treats systems with refrigerant charge of 125 lbs. – 250 lbs.
4050-06
4050-01
4050-02
4050-10
4051-99
A/C EasyDry
This product is a quick and simple way to prevent and eliminate moisture in a system.
A/C EasyDry contains a dehydrating agent that converts system moisture into a natural
organic material that is compatible with and mixes with the lubricant. It is great for preventing
acid formation, which is caused by moisture in a system, and it works with all refrigerants
(except ammonia). Each can will treat up to a 5 ton system and is easily installed with the
reusable piercing valve and hose.
3 ounce pressurized can
A/C Piercing Valve and Hose
4051-06
4051-99
Visitus
usatatwww.nucalgon.com
www.nucalgon.comor
orcall
call1-800-554-5499
1-800-554-5499
Visit
11
Total System Protection
Total System Protection
Endorsed by York®, Goodman®,
Nordyne®, Coleman®, and Daikin®
Rx11-flush®
R x11-flush is a unique solvent engineered specifically for flushing refrigeration and air conditioning systems. R x11-flush is ozone-safe,
non-toxic, and non-flammable. Used exactly like the old R-11 flushing process, its patented HFC-based solvent formulation is powerful
enough to flush away sludge, carbon residues, oils, acids, water and other particulates. R x11-flush is ideal for system flushing after
burnouts, during retrofits and for flushing line sets for R-410A conversions. Rx11-flush has been the industry’s standard for over a
decade, and contractors agree — it’s the best flush for R-410A retrofits and after compressor burnouts.
Rx11-flush Starter Kit
1 lb. canister
"2+1" Display Pack
2 lb. canister
13 lb. canister
26 lb. canister
Contains a 1 lb. canister, Rx11-flush Gun and Hose, and Injection Valve
Recommended for a 3-4 ton system
Contains one Injection Valve and two 2 lb. canisters
Recommended for a 5-7 ton system
Recommended for up to 50 ton system
Recommended for systems over 50 tons
4300-08
4300-09
4300-10
4300-11
4300-15
4300-26
Rx11-flush® Liquid
R x11-flush Liquid is a new and improved chemistry that is the next generation in
flushing technology. It remains a constant boiling solvent, and its stronger, fasteracting formula dissolves more oil, moisture and contaminants than any other flush. It is
ideal for line sets, burnouts, and other flushing requirements.
19.5 ounce can
Rx11-flush Liquid Starter Kit
4300-30
4300-38
Rx11-flush® Accessories
The R x11-flush product family also includes various support tools. This includes the
Injection Valve for hooking up to a charging hose for flushing and the Flushing Tool
for facilitating line set flushing. In addition, the R x11-flush Gun with a built-in flushing
attachment and the R x11-flush Hose (24˝) are available.
Flushing Tool
Rx11-flush Gun
Rx11-flush Hose (24˝)
Injection Valve
4300-50
4300-51
4300-52
4300-89
(Injection Valve fits Pneu-flush® and pressurized Rx-Acid Scavenger® as well)
2
A/C Re-New®
A/C Re-New is a highly formulated, OEM approved product that has established an outstanding track record enhancing the performance
of air conditioning and refrigeration systems. A/C Re-New frees sticky valves, quiets noisy compressors, reduces energy consumption
by lowering starting and running amps, and improves heat transfer in the evaporator and condenser. It’s great for new systems as a
preventative or to reinstate performance of older systems.
1 quart can
4 fluid ounce can
A/C Re-New Injector Tool
4057-54
4057-55
4057-99
Rx-Acid Scavenger®
The most effective way to neutralize or “scavenge” acid in refrigeration and air conditioning
systems. It is perfect for use after burnouts or during normal on-going system maintenance.
In addition, Rx-Acid Scavenger can be used with all lubricants: mineral, alkylbenzene and
polyol ester. Now available in a pressurized can for easy injection into charged systems or
hermetically sealed systems.
2 fluid ounce unpressurized bottle
3.8 ounce pressurized can
Injection Valve
4301-02
4301-05
4300-89
(Injection Valve fits Rx11-flush® and Pneu-flush® as well)
Phase III® Refrigeration Oil Acid Test Kit
Formulated for use with POEs as well as mineral oils and alkylbenzene, Phase III is an
inexpensive, disposable test kit that provides proof-positive that acid level in refrigeration oil
is either safe or unsafe. Phase separation makes it easy to see change in color of acid indicator
(even if a leak detection dye has been added to the oil). Just two bottles to work with, it is
simple, safe, accurate, and small enough that you can carry several in your tool box.
1 each
4320-W8
How to Test Oil with Phase III®
1.Pour the solution from the small bottle into
the large bottle. The bottom layer of this
mixture will be purple.
2.Completely fill the small bottle with oil from
the unit being tested. Do this immediately
after the oil is removed from the crankcase,
since exposure to air will contaminate the oil
and give a false test result.
3. Pour the oil into the large bottle and shake well.
4. Wait two to three minutes. A phase separation
will develop as the oil rises to the top of the
mixture and an aqueous layer forms on the
bottom.
5.If the bottom layer:
Stays purple- the oil is satisfactory.
Turns light pink or loses color completelythe oil has higher than acceptable acid
content.
Visit us at www.nucalgon.com or call 1-800-554-5499
Good Oil
Bad Oil
3
Total System Protection
Total System Protection
Coil Cleaner Selection Guide
Coil Cleaner Selection Guide
Nu-Calgon Coil Cleaners
Found on Pages 6-7
Nu-Brite®
Foam-Brite®
Alka-Brite® Plus
CalClean®
Special HD
CalClean®
TriClean™ 2x
Nu-Solve™ NR
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Cal-Brite®
Tri-Pow’r® HD
EQUIPMENT USED ON
•
Condenser Coils
•
•
•
Mini-Split Condenser Coils
•
Small Condenser Coils
•
•
Evaporator Coils
Mini-Split Evaporator Coils
•
Small Evaporator Coils
Microchannel Coils
•
Electronic Air Filters
Fan Blades,
Permanent Filters
•
•
•
•
•
•
•
•
•
•
FORMULATED TO REMOVE
Greasy Dirt & Oil
•
•
•
Cooking Grease
•
•
•
Lint, Dust, Dirt & Grime
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Alkaline
Alkaline
Alkaline
•
•
•
Tobacco Tars
Oxide (Corrosion) Deposits
•
•
•
•
Cottonwood/ Bugs
•
•
•
•
•
FEATURES & BENEFITS
Product Type
Alkaline
Alkaline
Alkaline
Acidic
Aerosol
Liquid
•
•
•
•
Brightening
•
•
•
•
•
Degreasing
•
•
•
•
•
Foaming
•
Alkaline
Alkaline
Aerosol
Liquid
•
•
•
•*
•*
•
•
EPA Registered Disinfectant
•*
No Rinse (Evaporators)
•
No Rinse (Condensers)
Biodegradable
•
•
USDA Authorized
•
•
•
•
•
•
•
•
•
•
•
•
U.S. EPA’s
Safer Choice Program
NSF Registered
•
•
•
•
•
•
* Dilution ratios for no rinse applications: Tri-Pow’r HD = 10:1, Liquid CalClean = 10:1 (Aerosol CalClean must be rinsed), Special HD CalClean = 40:1, Green Clean = 10:1
4
Nu-Calgon Coil Cleaners
Found on Pages 7-9
Evap-Powl’r®-C
Evap-Fresh®
No Rinse
Cal-Green™
Evap-Green™
Green Clean
Evap-Foam® Blackhawk®
Nu-Blast® &
Cal-Blast®
CompleteCare
Mini-Split Kit
EQUIPMENT USED ON
Condenser Coils
•
•
•
•
Mini-Split Condenser Coils
•
•
•
•
Small Condenser Coils
•
•
•
•
Evaporator Coils
•
•
•
•
•
•
•
Mini-Split Evaporator Coils
•
•
•
•
•
•
•
Small Evaporator Coils
•
•
•
•
•
•
•
Microchannel Coils
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Alkaline
Alkaline
Solvent
Alkaline
•
•
•
Electronic Air Filters
Fan Blades,
Permanent Filters
•
FORMULATED TO REMOVE
Greasy Dirt & Oil
•
•
•
•
Cooking Grease
Lint, Dust, Dirt & Grime
•
•
•
•
•
Tobacco Tars
Oxide (Corrosion) Deposits
Cottonwood/ Bugs
FEATURES & BENEFITS
Product Type
Alkaline
Alkaline
Alkaline
Alkaline
Alkaline
Aerosol Liquid
•
Foaming
•
Brightening
•
Degreasing
EPA Registered Disinfectant
No Rinse (Evaporators)
•
•
•
•
•
•
•
•
•*
•
•
Biodegradable
•
USDA Authorized
•
NSF Registered
•
•
No Rinse (Condensers)
U.S. EPA’s
Safer Choice Program
•
•
•
•
•
•
•
•
•
•
•
•
•
Visit us at www.nucalgon.com or call 1-800-554-5499
•
5
Coil Cleaner Selection Guide
Coil Cleaner Selection Guide
Coil Cleaners
Coil Cleaners
Nu-Brite®
Nu-Brite is the most effective coil cleaner available today. It foams, brightens, and is an equally effective yet safer alternative to HF acidbased products. It produces a high volume of foam that cleans more effectively than acids, particularly in removing grease. Biodegradable.
The liquid versions are USDA approved and NSF registered.
18 ounce can
1 gallon bottle
2.5 gallon pail
55 gallon drum
4291-18
4291-08
4291-05*
4291-01
Foam-Brite®
The ultimate in foaming alkaline cleaners, Foam-Brite cleans and brightens while at the same
time providing tremendous foaming to push dirt and grime out of the coil. Can easily be used
in place of the more dangerous HF acid-based products. Biodegradable. NSF registered.
1 gallon bottle
2.5 gallon pail
55 gallon drum
4178-08
4178-05*
4178-01
Alka-Brite® Plus
A non-acid, alkaline based product for brightening and cleaning air-cooled condensers, AlkaBrite Plus contains the best available detergents to quickly penetrate and remove oxidation.
Its foaming action helps to lift greasy soils out of the coil. Biodegradable. NSF registered.
1 gallon bottle
2.5 gallon pail
55 gallon drum
4120-08
4120-05*
4120-01
Cal-Brite®
Cal-Brite is a low pH cleaner developed for cleaning evaporator coils, air-cooled condensers
and other finned cooling and heating coils. Its versatility is based upon glycolic acid and other
unique ingredients. It provides moderate foaming and brightening and is safe for use indoors as
well as outdoors. It’s particularly suitable when lime scale must be removed from outdoor coils.
1 gallon bottle
55 gallon drum
4133-08
4133-01
* A 2.5 gallon pail wrench is also available. Part Number ZE64.
6
TriClean 2x™
The new way to clean a condenser coil. Simply connect to hose, clean, and rinse. TriClean 2x is
metal-safe, designed for rapid emulsion of soils from the coil. Restores efficiency and is ideal
for painted fin and microchannel coils. Eliminates the need for a sprayer.
1 quart sprayer with hose connector
4372-24
Nu-Solve™ NR
Ready-to-use, non-rinse condenser coil cleaner for situations with limited water availability
for rinsing. Nu-Solve NR is also for other applications where it is desirable to have less diluted
cleaning solution on a commercial roof or when a solvent-based aerosol approach is not practical.
Nu-Solve NR effectively emulsifies dirt and grime and provides a benefit of leaving a protective
treatment on the aluminum for added corrosion protection, making the next cleaning easier.
Nu-Solve NR can be applied with Nu-Calgon's poly sprayer or the Nu-Solve NR Sprayer (page 10).
1 gallon bottle
4295-08
Tri-Pow’r® HD
An outstanding general purpose coil cleaner, providing detergency and degreasing as well as
deodorizing capability. Its positive emulsion technology is very effective against oily grime as
it converts the deposits into a more fluid or liquid form that can be easily rinsed away. It is nonacid, non-toxic, and biodegradable. NSF registered. Also great for microchannel coils.
1 gallon bottle
55 gallon drum
4371-88
4371-81
CalClean®
An alkaline detergent formulated for cleaning evaporator coils, air-cooled condenser coils, metal
filters, fan blades, and other surfaces soiled with grease, dust and dirt. Biodegradable. USDA approved.
Aerosol is NSF registered. Also great for microchannel coils.
20 ounce can
1 gallon bottle
2.5 gallon pail
55 gallon drum
4081-75
4135-08
4135-06*
4135-01
Special HD CalClean®
The best non-foaming cleaner available. Specifically formulated to remove tobacco tars from
electronic air cleaners as well as the most stubborn deposits from finned coils. USDA approved.
Also great for microchannel coils.
1 gallon bottle
2.5 gallon pail
55 gallon drum
4143-08
4143-06*
4143-01
* A 2.5 gallon pail wrench is also available. Part Number ZE64.
Evap Pow’r®-C
A no-rinse product formulated for cleaning evaporator coils. It is metal-safe, and it cleans and
emulsifies even the most stubborn soils and deposits. Biodegradable. USDA approved. Also
great for microchannel coils.
1 gallon bottle
2.5 gallon pail
55 gallon drum
4168-08
4168-05*
4168-01
Visit us at www.nucalgon.com or call 1-800-554-5499
7
Coil Cleaners
Coil Cleaners
Coil Cleaners
Coil Cleaners
Evap Foam No Rinse®
Evap Foam No Rinse is a high-performing, heavy-duty detergent. It is formulated with
special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse
product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on
cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down.
NSF registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach
locations (see page 18).
18 ounce can
4171-75
Evap-Fresh® No Rinse Evaporator Coil Cleaner & Disinfectant
Evap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively
cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect
for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment,
and evaporator coils. EPA registered specifically for use on HVAC equipment.
18 ounce can
1 gallon bottle
4166-75
4166-08
The following products are part of Nu-Calgon’s Environmentally Friendly Green Select line.
These coil cleaners meet the U.S. EPA Safer Choice Program standards, making them a
safer choice for the user and the environment.
Cal-Green™ Condenser Cleaner
Cal-Green is a plant-based, natural condenser cleaner that is powerful enough to remove
dirt, grease, and grime. It meets the U.S. EPA Safer Choice Program standards, making it a
safer choice for the user and the environment. This non-foaming, non-toxic concentrate is
perfect for cleaning residential or commercial systems and restores their efficiency while
being environmentally responsible. Also OEM approved for microchannel coils.
1 gallon bottle
55 gallon drum
4190-08
4190-01
Evap-Green™ Evaporator Cleaner
Evap-Green is a no-rinse product that is perfect for numerous heating and air conditioning
applications, such as evaporator coils, roof top units, window units, metal filters, fan blades,
and more. Evap-Green meet the U.S. EPA Safer Choice Program standards, making it a safer
choice for the user and the environment . Evap-Green is also biodegradable and will not
harm plants, animals, and aquatic life. Metal-safe — meets OEM guidelines for all aluminum
coils, including microchannel types.
1 gallon bottle
55 gallon drum
4191-08
4191-01
Green Clean
A pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid
removal of grease and other heavy soils. It can be used right out of the bottle or diluted
for milder jobs. Biodegradable. Also great for microchannel coils.
1 quart spray bottle
1 gallon bottle
55 gallon drum
8
4186-24
4186-08
4186-01
Coil Cleaners
Coil Cleaners
Blackhawk®
Blackhawk is an expanding foam coil cleaner. Formulated to deeply penetrate the coil, it
liquefies to quickly remove grease, grime, or oily soils from deep within the coil. Blackhawk’s
formulation is safe and problem-free for cleaning evaporator or condenser coils in an occupied
building; produces no objectional fumes. It is particularly effective on coils on refrigerators,
coolers, and freezers located in restaurants and other commercial establishments. NSF
registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach
locations (see page 18).
18 ounce can
4127-75
Nu-Blast®
A no-rinse condenser coil cleaner in a convenient aerosol package. Double action of highpressure blast and solvent cleaning restores design efficiency of condenser coils. It is
non-flammable and non-conductive. No rinse required — cleaning solvent evaporates
completely. Use with adequate ventilation.
18 ounce can
4290-75
Cal-Blast®
Cal-Blast is a no-rinse condenser cleaner that will powerfully separate undesirable materials
from the surface, offering maximum cleaning of finned coils. It’s a high-performance aerosol
with excellent solvency and blasting spray.
20 ounce can
4132-20
Coil Protectants
NEW
DuraCoil
DuraCoil is a long-lasting coating for coils and surfaces in corrosive environments. It uses a
durable, OEM-approved Heresite® Coating. DuraCoil has a fast, air-dry formula that bonds
to all metals and causes negligible heat transfer loss across the coil. Great for repairing an
OEM-approved coil coating that has been compromised while in service! Brown in color.
11 ounce can
4183-90
Cal-Shield®
Cal-Shield is a synergistic liquid formulation based upon DuPont’s Teflon® fluoro-additives. It’s
designed for application on air-cooled condensers, evaporator coils, and other finned heating
and cooling coils. Cal-Shield will shield and protect the coil from adverse conditions.
1 quart spray bottle
1 gallon bottle
4148-32
4148-08
Nu-Shield®
Nu-Shield, the newest generation of chemistry for protecting
coils and other surfaces, is a super-hydrophobic (water repelling)
product. The non-conductive formula has numerous applications
in the management of water on non-food, non-potable water
surfaces for the HVACR trade. Simply spray it on and watch the
water bead up and roll right off.
9 ounce can
Non-treated : Nu-Shield :
Water Clings Water Repels
4294-75
Visit us at www.nucalgon.com or call 1-800-554-5499
9
Sprayers
Sprayers
NEW
Coil Gun®
Coil Mate™ Coil Cleaning Hose
Nu-Solve NR Sprayer
A “hose-end” sprayer that features five
different mix ratio settings designed for
coil cleaners. Utilizes a 2 quart capacity
bottle and includes a foam wand as well
as “quick disconnect” capability. The Coil
Gun Probe accessory has a 90º direction
of spray that allows cleaning from inside
the coil. It also provides easy access in
tough-to-reach locations.
Durable 5/8 inch diameter reinforced
hose with Flex-Guard protection. The
50-foot hose is equipped with solid
brass wrench fittings. The Coil Mate is a
necessity when using the popular Coil
Gun® or rinsing an air-cooled coil with
water after using a Nu-Calgon coil cleaner.
Backpack-type sprayer developed for
applying Nu-Solve NR, a non-rinse outdoor
coil cleaner when water availability for
rinsing is an issue. Sprayer utilizes a fourgallon tank with no holes or connections at
the bottom to leak! Provides high-pressure
spray for added cleaning effectiveness,
large pressure chamber for lasting
pressure, and a flexible and rugged
wand with an adjustable spray nozzle.
Replacement parts are available for all Nu-Calgon sprayers. Contact your local wholesaler.
Coil Gun
Coil Gun Probe
4774-0
4774-1
Coil Mate
Hot Water Hose
Plastic Pistol Grip Nozzle
61231
61238
61241
1 each
4775-0
No. 50P Poly Sprayer
No. 100P Poly Sprayer
No. 200P HiPressure Poly Sprayer
The No. 50P is constructed of highdensity translucent polyethylene. It
has a half gallon (3 pint) capacity. The
nozzle is adjustable and the flow rate
is controlled by a thumb lever. It comes
with a 7˝ polyethylene pump.
This sprayer is constructed of highdensity translucent polyethylene. It has
a funnel top for easy chemical pouring
and a 1 gallon working capacity. It
comes with a 8˝ polypropylene pump,
brass handle and extension tube with
adjustable nozzle, a wear-resistant hose,
and a pressure relief valve.
The No. 200P HiPressure Poly
Sprayer is constructed of high-density
translucent polyethylene. It has a 2
gallon working capacity, funnel top,
pump handle, and all-brass hardware.
No pumping is required. Pressurize the
sprayer with water through a “quick
disconnect” fitting.
1 each
4770-0
1 each
4770-2
1 each
4771-2
No. 220CP Poly Sprayer
No. 300P Poly Sprayer
Multi-Purpose Sprayer
The No. 220CP Poly Sprayer is
constructed of high-density translucent
polyethylene with a funnel top that
provides easy chemical pouring. This 2
gallon capacity sprayer features an easy
fill level indicator and comes with an 8˝
pump and a high resin plastic adjustable
nozzle with three feet of hose.
1 each
4771-3
The No. 300P Poly Sprayer is constructed
of high-density translucent polyethylene.
It has a funnel top and a 3.5 gallon capacity
(3 gallon working capacity). It comes with
a 10˝ Celcon pump, brass extension tube
with adjustable nozzle, and five feet of
vinyl hose.
A 24 ounce capacity sprayer. It is ideal
for small cleaning jobs, such as window
units and water coolers.
10
1 each
4772-0
1 each
4768-W3
Evap-Fresh® No Rinse Evaporator Coil Cleaner & Disinfectant
Evap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively
cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for
air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and
evaporator coils. EPA registered specifically for use on HVAC equipment to kill H1N1 and
other viruses such as Norwalk, Rhoto, Hepatitis, Rabies MRSA, and more.
18 ounce can
1 gallon bottle
4166-75
4166-08
CompleteCare Mini-Split Kit
The CompleteCare Mini-Split Kit cleans, disinfects, and deodorizes mini-splits, as well as controls
mold and mildew. It also protects condensate pans and lines from plugging. Each kit treats 2-3
mini-splits. Contains one 18 oz. can of Evap-Fresh No Rinse and one PurCool® Green Mini Strip.
1 each
4151-08
Bio-Fresh® cd
A ready-to-use bacteriostatic, fungistatic, and deodorizer based upon chlorine dioxide
technology. Inhibits the growth of bacteria, mold, mildew, fungi, and yeasts in IAQ
applications, and it may be applied to occupied spaces. Its EPA registration applies to HVACR
ventilating equipment, including coils, condensate pans, filters, and duct-work. Easily applied
by spraying, brushing, sponging, or wiping. EPA registered.
1 quart spray bottle
1 gallon bottle
4126-34
4126-38
Bio-Fresh® Fogger
The Bio-Fresh Fogger is made of a one-piece, seamless heavy-duty copolymer. It uses a 48˝
flexible hose and is adjustable from 0-18 ounces per minute with the respective particle size at
20 to 80 microns. It’s ideal for spraying Bio-Fresh cd in duct work and large areas.
1 each
4693-0
Drain Solve
Ideal for condensate pan drains. Drain Solve saves time and money with its ease of use. It
eliminates application concerns associated with more reactive, fuming drain openers. Simply
pour it down the drain and let it work without fear of noxious fumes or reactions. Does not
contain sulfuric acid.
1 quart
1 gallon
4165-24
4165-08
A/C Drain Sucker®
A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain
line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow
problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free
flowing drains, as well as all fittings and hoses for suction or pressure applications.
Nu-Calgon Number
ClenAir Number
A/C Drain Sucker kit
61308
CADS1
PurCool Pan Strip - treats 3 tons - 6 mos.
61043
1903D
Visit us at www.nucalgon.com or call 1-800-554-5499
11
Indoor Air Quality
Indoor Air Quality
Indoor Air Quality
Indoor Air Quality: ClenAir by Nu-Calgon
The Original ClenAir™ Odor Neutralizer
ClenAir’s unique odor neutralizing formula removes odors quickly and permanently. It is a
true odor eliminator, not a mask. Originally designed for use in central air systems, on fire and
flood restoration jobs and in sewage facilities, ClenAir is a professional product, yet it leaves no
lingering antiseptic or perfume smell. It is great for odors caused by fuel oil, smoke, pets, mold
and mildew, cigarette and cigar smoke, decay, cleaning solvents and even skunks. ClenAir has
three different scents: Original, CherryAir, and OrangeAir. The scents come in multiple sizes for
multiple applications.
Original
Mini Tub
1/2 lb. Tub display box
1/2 lb. Tub
1 lb. Tub
3 lb. Tub
CherryAir
Mini Tub
1/2 lb. Tub display box
1 lb. Tub
OrangeAir
Mini Tub
1/2 lb. Tub display box
1 lb. Tub
Nu-Calgon
ClenAir
61000
61001
61002
61003
61004
CA1500M
1500D
1500
1501
1503
Nu-Calgon
ClenAir
61018
61010
61011
CA1800M
1800D
1801
Nu-Calgon
ClenAir
61028
61020
61021
CA1300M
CA1300D
CA1301
Original
10 lb. Tub
30 lb. Tub
Wall Unit (White)
Nu-Calgon
61005
61006
61007
Gel Brick for Wall Unit (1lb.) 61008
CherryAir
3 lb. Tub
10 lb. Tub
30 lb. Tub
OrangeAir
3 lb. Tub
10 lb. Tub
30 lb. Tub
ClenAir
1510
1530
1300
1401
Nu-Calgon
ClenAir
61013
61015
61017
1803
1810
1830
Nu-Calgon
ClenAir
61023
61025
61027
CA1303
CA1310
CA1330
HVAC Odor Block®
ClenAir HVAC Odor Block is not a perfume mask or cover-up. The unique ClenAir formula
molecularly reacts with the airborne odor-causing compounds and eliminates them and
other indoor pollutants, leaving clean, fresh, air behind. The HVAC Odor Block makes it easy
to remove odors and improve the indoor air quality in the entire home or building by treating
the air through the HVAC system. Use in A/C units, furnaces, rooftop units, fan coil units, and air
handlers. Part numbers 61060 and 61061 last up to 3 months. The HVAC Odor Block XL (61070)
lasts up to 6 months.
Side Vent for
Carbon Filtration
Nu-Calgon Number
61060
61070
61061
Residential HVAC Odor Block
Residential HVAC Odor Block XL
Commercial HVAC Odor Block
ClenAir Number
1502
CA1015
ClenAir Liquid Formula
ClenAir Liquid is a fast acting deodorizing product. It eliminates odors via an oxidation
process while leaving a fresh scent. Applications include HVACR equipment, such as
evaporator coils, duct work, condensate pans, refrigeration cases, reach-ins, and walk-in
boxes. It can also be poured down drains, garbage disposals, and in trash cans. Spray in
restrooms, locker rooms and on fouled carpeting and upholstery. Used by hospitals, nursing
homes, and HVACR technicians.
Nu-Calgon
Unscented Spray 16 oz. 61030
Unscented Liquid 1 gal. 61031
Citrus Spray 16 oz.
61033
12
ClenAir
1600D
1610
1700D
Citrus Liquid 1 gal
CherryAir Spray 16 oz.
CherryAir Liquid 1 gal.
Nu-Calgon
ClenAir
61035
61037
61038
1710
1900D
1910
Indoor Air Quality
Indoor Air Quality
NEW
Gel Tabs - Condensate Drain Pan Treatment
Formulated with a breakthrough technology for treating air conditioning drain pans and lines. Keeps the drain pan from clogging
and eliminates foul and musty odors. When activated by condensation, the tablet will turn to gel and lock into place. Dissolves
continuously and completely with nothing left to remove for up to three months. Stack together to increase duration.
3 ton tab (12 in tube)
3 ton tab bulk (200)
5 ton tab (6 in tube)
4185-03
4185-04
4185-05
5 ton tab bulk (100)
15 ton tab (1 each)
20 ton tab (1 each)
4185-06
4185-15
4185-20
PanPads
A product formulated to eliminate the build-up of bacteria and slime growths in air
conditioning and refrigeration condensate drain pans. In laboratory tests, it has been proven
effective against a wide spectrum of harmful bacteria, including Legionella. The product is
EPA registered for this application. NSF registered.
5 (up to 5 tons)
4295-34
5 Slim (up to 5 tons) 4295-36
15 (up to 15 tons)
45 (up to 45 tons)
4296-24
4296-45
Pan-Treat®
Pan-Treat condensate tablets control odors and prevent overflows caused by plugged
condensate drain lines. They can also be used in humidifiers. They are very easy to use, as well
as non-corrosive, non-toxic, and biodegradable.
1 bottle (200 tablets)
4296-60
PurCool® Strips
PurCool Strips keep A/C and refrigeration condensate drain pans clean and free flowing. Use
PurCool Strips to prevent condensate drain clogs, costly overflows, and corrosion. Just place
them anywhere in the drain pan where the PurCool Strip will contact the condensate water
and enjoy up to six months of economical protection. PurCool Strips will adhere to the drain
pan and will not float or move. Dissolves completely, leaving no residue. Safe for metal and
plastic drain pans.
Nu-Calgon ClenAir
3 ton strip
61043
3 ton strip bulk (100) 61047
5 ton strip
61042
1903D
1903D-100
2001D
10 ton strip
30 ton strip
Visit us at www.nucalgon.com or call 1-800-554-5499
Nu-Calgon
ClenAir
61041
61040
2003D
2009
13
Indoor Air Quality
Indoor Air Quality: ClenAir by Nu-Calgon
PurCool® Green Strips and Tablets
PurCool Strips/Tablets prevent slime, sludge, odors, and overflow of condensate pans. Time
release formula adheres to pan and fully dissolves over time. PurCool Green Strips/Tablets
use plant-based suspending and dispersing action to keep drain pans clean and free flowing.
Products are available for commercial, residential, and mini split applications. Sizes are based on
system tonnage, with each strip/tablet lasting up to six months.
PurCool Green Mini Strip
PurCool Green Commercial Strip 10 ton
PurCool Green Commercial Strip 30 ton
PurCool Green 3 ton tablet
PurCool Green 3 ton bulk (200)
PurCool Green 5 ton tablet
PurCool Green 5 ton bulk (100)
Nu-Calgon Number
61044
61045
61046
61048
61049
61051
61052
ClenAir Number
PCG5MS
PCG10T
PCG30T
PCG5T
PCG5T-100
PurCool® Tablets
PurCool Tablets utilize a powerful formulation to keep condensate drain pans clean and free
flowing. Use PurCool Tablets to remove sludge and slime in A/C condensate pans to prevent
costly water damage caused by overflows. They will control clogs, build-up, odors, and
corrosion in drain pans, condensate pumps, and humidifiers.
Nu-Calgon Number
61053
1 bottle (200 tablets)
ClenAir Number
PC200
HVAC Carbon Block® In-Duct Air Purification System
HVAC Carbon Block is an add-on carbon purifier for all HVAC systems. Improves indoor air
quality by removing odors, indoor air pollutants, and VOCs. Treats up to 10 tons for up to
nine months.
Nu-Calgon Number
61062
HVAC Carbon Block
ClenAir Number
CACB10
Humidifier Panel™ Replacements
ClenAir Universal Humidifier Panels provide optimum moisture output, performance,
and durability. They replace Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others.
Ultra Upgrade Humidifier Panels' material retains water, increasing moisture output and
reducing water waste by up to 50%. They replace Aprilaire, Honeywell, Carrier, Bryant,
Lennox, ICP, and others.
Universal Humidifier Panel - #10 size
Universal Humidifier Panel - #12 size
Universal Humidifier Panel - #35 size
Ultra Upgrade Humidifier Panel - #10 size
Ultra Upgrade Humidifier Panel - #35 size
Nu-Calgon Number
61250
61251
61252
61254
61255
ClenAir Number
CA10
CA12
CA35
CA10UP
CA35UP
Spacegard® Filter Media Replacements
These Merv 11 filter media are direct replacements for the Aprilaire Spacegard 201 and 401. Merv
11 media removes pollen, allergens, smoke, dust, dust mites, bacteria, spores, and pet dander.
The large filter surface area provides for low resistance and longer filter life, more than 6 months!
Nu-Calgon Number
Replacement for Aprilaire Spacegard 201 61256
Replacement for Aprilaire Spacegard 401 61257
ClenAir Number
CA201
CA401
*Aprilaire and Spacegard are registered trademarks of Research Products Corporation
14
Gas Leak Detectors
Gas Leak Detectors
Cal-Blue® Plus Gas Leak Detector
Cal-Blue Plus is a complete gas leak detector with freeze protection to 5˚F. Its high viscosity formula enables it to remain in
contact with the applied surface for an extended period of time, allowing it to detect the smallest of leaks. The longest lasting
bubbles in the industry! It is also non-corrosive to metal, and it will not affect ultraviolet or black lights. NSF registered.
6 ounce bottle with dauber
1 quart spray bottle
1 gallon bottle
4182-53
4182-24
4182-08
Cal-Blue® LT Gas Leak Detector
The same high quality formulation as regular Cal-Blue Plus, but it has added freeze protection
to -20˚F. It is the ideal detector for geographical areas that may experience very cold
temperatures. The longest lasting bubbles in the industry! NSF registered.
1 quart spray bottle
1 gallon bottle
4183-24
4183-08
Gas Leak Detector
The original industry leak detector. A high viscosity liquid that forms bubbles when daubed
on a gas leak. Non-corrosive, non-staining, and harmless to skin. Detects any type of gas leak,
such as air, compressed air, carbon dioxide, nitrogen, natural gas, and refrigerant gases. Freeze
protection to -20˚F. Six ounce plastic bottles have dauber in cap. USDA approved.
6 ounce bottle with dauber
4180-53
Fluorescent Gas Leak Detector
A fluorescent formulation that provides improved visibility and long lasting bubbles.
It is non-corrosive to metals and is freeze protected to 5˚F. Suitable for high and low
temperature applications. Can be used for most refrigerants, natural gas and oxygen
systems. USDA approved.
8 ounce bottle with dauber
1 quart spray bottle
1 gallon bottle
4184-53
4184-24
4184-08
AccuTrak® Ultrasonic Leak Detector
Model VPE - Now with touchprobe included. Patented technology detects the ultrasonic sound
of a leak!
Nu-Calgon Number ClenAir Number
AccuTrak® Ultrasonic Leak Detector
61307
CAVPE
Visit us at www.nucalgon.com or call 1-800-554-5499
15
Refrigeration Oil & Vacuum Pump Oil
Polyol Ester (POE) Lubricant
Emkarate® RL Lubricant
The Emkarate family of polyol ester refrigeration lubricants are designed specifically for use with HFC refrigerants. They are available
in a range of viscosities. They have excellent thermal and chemical stability, and they are compatible with a wide range of elastomers,
polymeric materials, and other materials of construction. Fully miscible and compatible with mineral oils and alkylbenzene lubricants
as well as with CFCs, HCFCs and HFCs.
Emkarate RL
22H
32H
32HB
32-3MAF
46H
68H
68HB
68HP
100E
100H
170H
220H+
220XL
Viscosity
100 SUS
150 SUS
150 SUS
150 SUS
200 SUS
300 SUS
300 SUS
300 SUS
500 SUS
500 SUS
850 SUS
1100 SUS
1100 SUS
1 Quart
4314-44
4314-64
4316-44
1 Gallon
4313-46
4314-46
4314-66
4315-46
4316-46
4316-86
4316-76
4317-66
4317-46
4318-26
4318-66
5 Gallon
53 Gallon
4314-45
4314-62
4314-65
4314-41
4314-67
4315-41
4316-41
4316-45
4316-85
4316-71
4318-25
4318-65
4318-75
4318-21
4318-61
Mineral Oil
C-3s, C-4s, C-5s Refrigeration Oil
These are mineral naphthenic lubricants manufactured by Calumet Lubricant Company and
available in three viscosities. They are specifically designed for today’s high performance
air conditioning and refrigeration compressors using CFC and HCFC refrigerants. These
compressors run at higher speeds and generate higher temperatures, and as a result, they
require better lubrication. Use of these oils will ensure continued efficient operation.
Nu-Calgon
C-3s
C-4s
C-5s
Viscosity
150 SUS
300 SUS
500 SUS
1 Gallon
4303-07
4304-07
4305-07
5 Gallon
4303-05
4304-05
55 Gallon
4303-01
4304-01
4305-01
Polyvinyl Ether (PVE) Lubricant
Idemitsu Polyvinyl Ether Lubricant
PVE lubricants provide for increased stability and lubrication. They do not hydrolyze in the
presence of moisture, a very important feature in HVACR applications. Additionally, they
are compatible with other refrigeration oils and process fluids. PVE lubricants also exhibit
compatibility and performance with frequently used anti-wear additives.
Idemitsu
FVC32D
FVC68D
16
Viscosity
32 SUS
68 SUS
1 Quart
4319-14
4319-24
Zerol® Alkylbenzene Refrigeration Oil
Zerol Refrigeration Oil is recommended for use in all refrigeration and air conditioning
applications using CFC and HCFC refrigerants. It is highly recommended by refrigerant and
compressor manufacturers for use with R-22 and other HCFC blends such as R-409A as it provides
many distinct advantages: excellent miscibility, excellent thermal stability, and low temperature
performance compatibility with mineral oils. It is the oil of choice for R-22 and R-502.
Zerol
150
200TD
300
400CA
500
Viscosity
150 SUS
200 SUS
300 SUS
400 SUS
500 SUS
1 Gallon
4310-07
4308-07
4311-07
5 Gallon
4311-05
4311-65
4312-05
55 Gallon
4310-01
4308-01
4311-01
Vacuum Pump Oil
Vacuum Pump Oil
Nu-Calgon’s Vacuum Pump Oil is a quality, high-grade lubricant that performs at the deepest
vacuum. It has a very low vapor pressure, and it has excellent lubricity for complete surface
protection. It contains no additives or detergents.
1 pint bottle
1 quart bottle
1 gallon bottle
4383-34
4383-24
4383-07
Refrigeration Oil Products
Refrigeration Oil Charging Pump
An oil pump for charging refrigeration oil into a system, even while it’s running. This pump can
be used for 1 gallon, 2.5 gallon, and 5 gallon containers. Incorporates an automatic bleed valve
that keeps pressure equalized inside the container and includes a tapered rubber adapter that
fits all container openings without the need for additional adaptors.
1 each
4814-40
Total Lube Refrigeration Oil Test Kit
Have a professional lab analyze the oil to help detect potential problems such as metal wear
or burnouts. The analysis will provide information on the oil’s moisture, total acid number,
viscosity, color, and spectrochemical analysis on 20 plus metals and compounds. Help prevent
potential downtime, burnouts, and costly oil changes by incorporating regular testing of the
refrigeration oil.
1 each
4996-0
Oil Refractometer
A precision optical instrument that allows for the rapid and accurate determination of the
refractive index of oil solutions. It will specifically assist in determining the percent of residual
oil remaining in a refrigeration system when converting it to a new refrigeration oil. Such
retrofits require converting the mineral oil to a polyol ester (POE) or polyalkylene glycol (PAG),
an alkylbenzene lubricant (Zerol®) to a POE, or a mineral oil to an alkylbenzene.
1 each
4815-0
CanVerter®
A hand-held pump used to remove or add oil to hermetic compressors. Easy to use; each stroke
pumps 1 ounce of oil.
1 each
4814-0
Visit us at www.nucalgon.com or call 1-800-554-5499
17
Refrigeration Oil & Vacuum Pump Oil
Alkylbenzene Oil
Aerosol Products
Aerosol Coil Cleaners
NEW
Evap Foam No Rinse®
Evap Foam No Rinse is a high-performing, heavy-duty
detergent. It is formulated with special surfactants
and alkaline cleaners that have been developed into a
foaming, no-rinse product. Evap Foam is ideal for use
on most coils, but it is particularly suited for use on
cooling or evaporator coils. The aerosol can be sprayed
either right side up or upside down. NSF registered.
Can be used with the Talon Flexible Aerosol Wand
(4776-0) for hard to reach locations.
18 ounce can
4171-75
Talon
Flexible aerosol wand for
Nu-Calgon’s Evap Foam No Rinse,
Blackhawk or PenetrateHD products.
Provides focused cleaner spray or
penetrant in tough-to-reach locations.
The Talon is highly flexible, retains shape
memory, and provides 27 inches of added
length to an aerosol canister for navigating
in tight quarters inside the equipment. The
reusable Talon is a must-have service tool!
1 each
Nu-Brite®
Evap-Fresh® No Rinse
Nu-Brite is a very effective degreaser and cleaner on
condenser coils. Its high foaming characteristic will help
push soil deposits out of the coil, leaving it clean and
bright. With proper ventilation, it can also be used as
a kitchen degreaser by emulsifying stubborn, resistive
grease deposits found on coils located in kitchens. Product
should be used where adequate rinsing is possible.
Evap-Fresh is a ready-to-use, no-rinse cleaner and
disinfectant for evaporator coils. It effectively cleans as
well as kills mold and bacteria. This one-step no-rinse
disinfectant cleaner is perfect for air conditioners,
commercial air handling units, HVAC cooling coils,
refrigeration equipment, and evaporator coils. EPA
registered specifically for use on HVAC equipment.
18 ounce can
4291-18
18 ounce can
4166-75
Cal-Blast®
Nu-Blast®
Cal-Blast is a no-rinse condenser cleaner that will
powerfully separate undesirable materials from
the surface, offering maximum cleaning of finned
coils. It’s a high-performance aerosol with excellent
solvency and blasting spray.
A no-rinse condenser coil cleaner in a convenient aerosol
package. Double action of high-pressure blast and
solvent cleaning restores design efficiency of condenser
coils. It is non-flammable and non-conductive. No rinse
required — cleaning solvent evaporates completely. Use
with adequate ventilation.
20 ounce can
4132-20
18 ounce can
Blackhawk®
Blackhawk is an expanding foam coil cleaner.
Formulated to deeply penetrate the coil, it liquefies to
quickly remove grease, grime, or oily soils from deep
within the coil. Blackhawk’s formulation is safe and
problem-free for cleaning evaporator or condenser
coils in an occupied building; produces no objectional
fumes. It is particularly effective on coils on refrigerators,
coolers, and freezers located in restaurants and other
commercial establishments. NSF registered. Can be
used with the Talon Flexible Aerosol Wand (4776-0)
for hard to reach locations.
18 ounce can
18
4776-0
4127-75
4290-75
CalClean®
CalClean is a heavy-duty detergent formulation
of surfactants, grease solvents, alkaline cleaners,
corrosion inhibitors, and water conditioners. Ideal
for cleaning window units as well as small evaporator
coils, air-cooled condenser coils, metal filters, fan
blades and other surfaces soiled with greasy dust and
dirt. NSF registered.
20 ounce can
4081-75
NEW
Nu-Shield®
Nu-Shield, the newest generation of chemistry for
protecting coils and other surfaces, is a super-hydrophobic
(water repelling) product. The non-conductive formula
has numerous applications in the management of
water on non-food, non-potable water surfaces for the
HVACR trade. Simply spray it on and watch the water
bead up and roll right off.
9 ounce can
4294-75
DuraCoil
DuraCoil is a long-lasting coating for coils and
surfaces in corrosive environments. It uses a durable,
OEM-approved Heresite® Coating. DuraCoil has a fast,
air-dry formula that bonds to all metals and causes
negligible heat transfer loss across the coil. Great for
repairing an OEM-applied coil coating that has been
compromised while in service! Brown in color.
11 ounce can
4083-90
A/C Shine® Superior Cleaner / Protectant
Pan-Spray®
A/C Shine is specially formulated to clean and protect the
painted metal surfaces of outdoor A/C condensing units.
It sprays on and wipes off quickly and easily without
water. For use on all outdoor unit painted surfaces.
Pan-Spray is an effective, easy-to-use waterproof
rubberized coating that won’t chip, flake, or peel. It’s ideal
for sealing out rust and corrosion as well as repairing leaky
condensate pans, cooling towers, swamp coolers, roofing,
gutters, and down spouts. Pan Spray is the perfect
solution for emergency and permanent repair.
12 oz.
Nu-Calgon Number
ClenAir Number
61118
ACS12
16 ounce can - White
16 ounce can - Black
4296-50
4296-51
Aerosol Lubricants
Break-n-Lube™
Food-Grade Silicone
This advanced technology 4-in-1 product is made
with CERFLON® for high performance in a non-drying
penetrating lubricant. It’s highly versatile with the
ability to penetrate, lubricate, displace moisture, and
provide superior resistance to corrosion. It’s specially
formulated to help free rusted parts and assemblies.
Food Grade Silicone sprays a perfect non-stick surface
on ice machine surfaces, vending machines, coin slots,
slicing machines, dairy machinery, and other food
processing and packaging equipment. An excellent
lubricant that prevents binding and sticking. Contains
ingredients approved by the FDA for food contact use.
USDA approved.
12 ounce can
4128-03
11 ounce can
4084-03
PenetrateHD® Super Penetrating Lubricant
V-Belt Dressing
Loosens rusted and frozen metal parts. Frees stuck fan
blades, blower shafts, pulleys, rusted nuts and bolts,
and any frozen, rusted, or seized metal part. Unique low
surface tension formula penetrates into the smallest
spaces and breaks and dissolves the bonds of rust and
corrosion. Lubricates and protects metals. Dielectric
strength 40,000 volts. Can be used with the Talon Flexible
Aerosol Wand (4776-0) for hard to reach locations.
V-Belt Dressing is specially formulated to penetrate and
extend modern V-Belt life. It is particularly effective in
maintaining V-Belt efficiency and performance under
today’s increasing performance requirements. It keeps
belts pliable, prevents slippage, and does away with
squealing and chattering. USDA approved.
12 ounce can
17 ounce can
12 ounce can - LV*
17 ounce can - LV*
11 ounce can
4086-03
61105
61106
61107
61108
* LV = Low VOC for California
Visit us at www.nucalgon.com or call 1-800-554-5499
19
Aerosol Products
Aerosol Specialty Products
Aerosol Products
Aerosol Adhesives
Spray-n-Bond™
Spray Adhesive
A wide web spray adhesive formulated specifically
for insulation and duct liner applications. Ideal
for porous surfaces, it is waterproof, flexible,
transparent, non-staining, and it can be used for
both temporary or permanent bonds. Formulated
with the environment in mind, it contains no
chlorinated solvents or ozone depleters, and it is
VOC-compliant in states such as California.
Spray Adhesive is a fast-drying, all-purpose product
that provides a strong, water-resistant, flexible bond. It
is translucent and does not penetrate or soak material
causing bleed-through. Spray Adhesive is excellent
for labeling, bonding, splicing and sealing paper,
cardboard, cloth, rubber, styrofoam, canvas, leather,
wood, and most plastics.
12 ounce can
12 ounce can
4080-04
4369-75
Aerosol Specialty Products
Pipe-Dri®
Nu-Kill® II Wasp and Hornet Killer
Aerosol insulation that provides a moisture barrier to
stop sweating and dripping on refrigeration lines, air
conditioning lines, and other cold surfaces. Quickly
adheres and dries to a hard waterproof coating. Pipe-Dri
makes it possible to insulate hard-to-reach areas.
A “quick-kill” spray formulation EPA registered to
instantly and effectively kill wasps, hornets, and yellow
jackets, from distances up to 20 feet. Nu-Kill II also kills
with residual action as wasps and hornets return to a
treated nest. The formula is safe in and around electrical
equipment, having a dielectric strength of 47,000 volts.
18 ounce can
4297-75
13.5 ounce can
Pump Protector
Zinc Rich Cold Galvanizing
When corrosion occurs in close-tolerance areas, it can
cause the impeller to stick or bind. Pump Protector
protects seasonally operated pumps against corrosion
during shutdowns by winterizing them. It is safe for all
types of water pumps and requires no special rinsing
at start-up.
Highly resistant to nearly all forms of corrosion. Perfect
for repairing factory galvanized material damaged in
shipment, welding, assembly, etc. Its 95% pure zinc film
fuses itself to iron, steel, or aluminum. Blends well with
hot-dip coating. Meets or exceeds military specifications
MIL-P- 26915A, MIL-T- 26433, MIL-P- 21035, MIL-P-46105
and the Preece Test.
10 ounce can
4299-T8
13 ounce can
4087-03
Electrical Contact Cleaner
Degreasing Solvent EF
Cleans, lubricates, and protects electrical contacts
from corrosion, and it is safe on most plastics. Cleaning
action quickly removes greases, dust, and oxidation,
restoring and maintaining precision and efficiency to
the instrument and component. Includes extension
tube for pinpointing application. USDA approved.
A degreasing solvent, specially formulated for cleaning
and degreasing equipment where washing or flushing
is not possible. Simply spray on and wipe off. Penetrates
quick and deep, loosening and liquefying heavy
greases and tar. Non-corrosive and non-staining with a
dielectric strength over 26,000 volts.
11 ounce can
14 ounce can - LV *
4082-03
4082-04
* LV = Low VOC for California and Canada
20
4292-75
14 ounce can
14 ounce can - LV*
4083-75
4083-83
* LV = Low VOC for California
Great Wipes
Great Wipes Industrial Strength Hand Towels are waterless wipes made specifically for the air
conditioning, refrigeration, and plumbing service technician. Each premoistened, heavy duty
towel has strong pumice scrubbing power that conveniently cleans anywhere and anytime.
75 count canister
4185-75
Scrubs-In-A-Bucket® HVAC80
The original Scrubs — disposable, pumice-performance waterless hand cleaner towels that
effectively and quickly clean hands on a wide variety of industrial soils and greases. Each selfdispensing portable canister contains 80 perforated disposable heavy-duty towels and are
pre-moistened with the famous Scrubs cleaning formulation. Effective yet gentle to the skin.
Use anywhere, anyplace, anytime.
30 count canister
80 count canister
4366-24
4366-87
Quick Seal™ Pipe Repair
A permanent knitted fiberglass impregnated tape that is designed for quick, in-the-field repair
of leaks for all types of pipes. It can be used on both cold or hot water as well as refrigeration,
plumbing, industrial, commercial, and residential applications. It is safe for potable water and
is UL listed. ANSI/NSF Standard 61.
2˝ x 3´ wrap
4˝ x 12´ wrap
4299-10
4299-11
Pneu-flush®
A flushing and cleaning system specifically designed for pneumatic control air lines. It utilizes
DuPont® Vertrel® XM, a premier ozone-safe HFC cleaning solvent. Pneu-Flush works quickly and
easily to clean and purge the compressed air lines in HVAC control and other pneumatic systems.
2 lb. canister
Injection Valve
4298-01
4300-89
(Injection Valve fits Rx11-flush® and Pressurized Rx-Acid Scavenger® as well)
Thermo-Trap®
The industry’s original heat absorbing paste designed to isolate heat encountered in
soldering, welding, and brazing, thereby preventing damage to nearby heat sensitive
controls, or fittings. USDA approved. Biodegradable. Available in paste or gel.
Thermo-Trap paste
Thermo-Trap gel
Thermo-Trap gel
11 ounce tube
1 quart spray bottle
4 fluid ounce spray bottle
4371-36
4371-32
4371-53
Degreasing Solvent EF
Degreasing Solvent EF is a volatile solvent, especially formulated to provide effective cleaning
and drying and reduce safety hazards. It leaves surfaces clean and oil-free. The thorough
cleaning action is superior to ordinary chlorinated solvents.
1 gallon
1 gallon - LV*
4162-07
4162-17
* LV = Low VOC for California
Visible Defects Heat Exchanger Inspection System
The Visible Defects Heat Exchanger Inspection System is a complete kit that enables the
technician to better evaluate the integrity of a heat exchanger. If a crack exists, the specially
formulated fluorescent penetrant visually enhances the crack, allowing the technician to see
the defect easier.
Visible Defects kit
Crack Finder replacement solution
4385-00
4385-06
Visit us at www.nucalgon.com or call 1-800-554-5499
21
Specialty Products
Specialty Products
Specialty Products
General Purpose Cleaners
Green Clean
A pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid removal
of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs.
Biodegradable. Also great for microchannel coils.
1 quart spray bottle
1 gallon bottle
55 gallon drum
4186-24
4186-08
4186-01
Spray Nine® Cleaner & Disinfectant
Spray Nine is a tough task cleaner and broad spectrum disinfectant. EPA-registered Disinfectant kills
harmful germs like HIV-1, Influenza, H1N1, Staphylococcus Aureus, Salmonella Choleraesuis and E. Coli in
45 seconds. Also helps prevent cross contamination. Authorized by USDA for use in federally inspected
meat and poultry plants with a C-1 rating.
Nu-Calgon Number
61110
61113
1 gallon
32 oz. spray
ClenAir Number
26801
26832
Grez-Off® Heavy Duty Degreaser
Grez-Off works hard so you don’t have to. This heavy-duty answer to heavy-duty grease and grime leaves
engines, machinery, asphalt, garage floors and more whistle clean. Biodegradable, non-flammable
formula hits hard and fast with less impact on user and environment.
Nu-Calgon Number
61116
61117
1 gallon
32 oz. spray
ClenAir Number
22701
23732
Other Specialty Products
Elite® Performance Windshield Washer Cleaner -20°
Elite Performance Windshield Washer is independently tested to provide freeze protection to -20°F.
Don’t take chances with generic washer products; only Elite Performance offers certified protection.
Nu-Calgon Number
61115
1 gallon
ClenAir Number
CAWW1G
ClenHands: Orange Smoothie™, Orange Crush™ and Cherry Crush™
Premium antimicrobial hand cleaners that quickly dissolve dirt, grease, fuel oil, pipe dope, resin, ink, paint, glue,
rubber gasket and tile cements and many other hard-to-remove soils. ClenHands Orange Smoothie is a smooth
non-pumice formula, while ClenHands Orange Crush is enhanced with fine-ground American pumice. ClenHands
Cherry Crush is a cherry-scented antimicrobial hand cleaner with pumice. For use with or without water.
Orange Crush with Pumice
Orange Smoothie Non Pumice
Orange Crush with Pumice
Cherry Crush with Pumice
ClenHands Super Gel
1 gallon
15 ounce
15 ounce
15 ounce
11 ounce
Nu-Calgon Number
61201
61202
61203
61204
61205
ClenAir Number
2201
2202
2215
2315
2414
Smoke Signal™ Smoke Candles and Smoke Pens
Smoke Signal generates smoke by chemical reaction, eliminating costly equipment and time to pinpoint leaks.
Smoke tests will effectively and inexpensively reveal leaks in heating and air conditioning duct work, furnaces,
fire boxes, exhaust fans and smoke detectors. Smoke Pens are also excellent for observing ventilation, air
balancing, smoke detectors, drafts, leakage, and air flow. The Smoke Pens come with one pen, six replacement
wicks (refills available) and instructions. Smoke Signal items contain no explosive materials.
Smoke Candle - 4000 cubic feet of smoke 30 sec. - 1A
Smoke Candle - 8000 cubic feet of smoke 60 sec. - 2B
Smoke Candle - 40,000 cubic feet of smoke 2-3 min. - 3C
Smoke Pen
Refill Package - 6 wicks
22
Nu-Calgon Number
61302
61303
61304
61305
61306
ClenAir Number
CAS30
CAS60
CAS180
CASP1
CASP1RW
Perma-Wrap™
Foam Insulation Tape
Formulated from the highest quality
elastomeric thermal insulation material.
Its closed cell construction seals out air
and moisture, slowing down heat transfer,
and can be used on hot or cold water
pipes, chilled water, and refrigerant lines
to prevent sweating and condensation.
Service temps as low as -20º F with a high
continuous temperature of 160º F and a high
intermittent temperature of 220º F.
2˝ x 1/8˝ x 30´ roll
4218-W3
2˝ x 1/8˝ x 30´ roll - 4218-12
dispenser package
Cork Tape
Formulated and manufactured as an
insulating material for preventing sweating
and condensation on refrigerant lines, cold
pipes, and other commercial refrigeration
and A/C systems. Serves as an excellent
insulator on hot pipes, and can also be used
as a gasketing material, a sound-deadening
material, and for wrapping valves, tees, and
fittings. Service at temps as low as -30ºF, as
high as 200ºF and won’t sag up to 350ºF.
2˝ x 1/8˝ x 30´ roll
4217-W3
Foam-Tite®
Cork-Tite®
An economically priced tape formulated
from quality thermal insulation material.
Closed cell construction and can be used
on cold water pipes, chilled water lines
and refrigerant lines to prevent sweating
and condensation. It can also be used
on hot water lines, for better insulation
against heat loss. Service temperatures of
-15ºF to 160ºF.
Designed to insulate cold pipes for all
kinds of air conditioners in cars, homes,
freezers, and refrigerators. Helps stop
condensation problems and is ideal for
blocking heat gain in cold pipes and
preventing heat loss in hot pipes. An
effective sound dampening material, it
can also be used for gasketing purposes,
sticks to dry metals and seals tightly
without drying. Flexible and does
not shrink or melt within the service
temperatures of -20 ºF to +200 ºF.
2˝ x 1/8˝ x 30´ roll
4219-12
2˝ x 1/8˝ x 30´ roll
4217-12
Foam Tape PE
Thumb-Tite®
Insulation tape providing an economical
way to prevent sweating or condensation
on air conditioning, refrigeration, chilled
water or other cold lines. Also used on hot
water lines for insulation against heat loss,
and it can be overlapped or the edges can
be pressed together.
Formulated and manufactured for use
in many sealing, insulating, and general
maintenance
applications.
Excellent
adhesion capability and is non-staining,
non-hardening, and unaffected by wide
variations in temperature — an excellent
thumbing grade. Each box contains two
1-pound bars.
2˝ x 1/8˝ x 30´ roll
4219-20
2 lb. box
4216-92
Nu-Foam®
Sealing and Caulking Cords
An expanding polyurethane prepolymer
foam used as a sealant and insulating
product on openings created for
refrigeration, air conditioning and heating
tubes or pipes, duct joints, and other areas
where unwanted air penetration might
occur. Contains no CFCs or any HCFCs and is
UL classified and fire retardant.
Nonstaining sealers formulated to be waterresistant, dust- resistant and white in color.
They securely adhere to most surfaces and
provide excellent insulation value. They are
available in 3/8˝ pre-shaped extruded cords,
with serrated release paper.
12 ounce can
20 ounce can
3/8˝ x 25´ roll
4216-27
4293-04
4293-75
Visit us at www.nucalgon.com or call 1-800-554-5499
23
Insulation Products
Insulation Products
Glycol
Propylene Glycol
Freez-Kontr’l®
An expanded family of heat transfer fluids (anti-freeze) based upon non-toxic propylene
glycol. All products are fully formulated to provide optimum freeze protection as well
as corrosion protection in chilled water, hydronic and other closed systems. Safe to use
where contact with potable water is possible. GRAS certified.
• Freez-Kontr’l — provides greater than -60 ºF freeze protection and
greater than -100 ºF burst protection.
• Freez-Kontr’l 95/5 — a fully concentrated (~100%), inhibited propylene glycol product.
• Freez-Kontr’l 35 — formulated with 35% propylene glycol for use as a
secondary coolant in supermarket rack applications.
• Freez-Kontr’l FG — a certified USP, food grade propylene glycol product
at ~100% concentration. Inhibited. NSF registered.
Freez-Kontr’l
Freez-Kontr’l 95/5
Freez-Kontr’l 35
Freez-Kontr’l FG
1 gallon bottle
5 gallon pail
55 gallon drum
5 gallon pail
55 gallon drum
55 gallon drum
55 gallon drum
4188-07
4188-05
4188-02
4188-06
4188-03
4188-35
4188-04
Burst-Kontr’l® AP-100
A specially formulated propylene glycol heat transfer solution for use in boilers having
aluminum heat exchangers. It has corrosion inhibitors to protect aluminum, copper, solder,
brass, and steel. Provides burst protection to -100 º F and freeze protection to -60 º F.
5 gallon pail
4187-15
Ethylene Glycol
Freez-Therm®
An inhibited heat transfer fluid and anti-freeze based upon ethylene glycol. It can be used
in chilled water, hydronic, and other closed systems for both freeze point suppression and
corrosion inhibition. An uninhibited version is also available in drums on special order.
1 gallon bottle
5 gallon pail
55 gallon drum
4189-07
4189-05
4189-01
Glycol Equipment
Glycol Refractometer
An accurate and economical tool for ensuring proper levels of glycol treatment in HVAC
fluid systems. Removes guess work and prevents wasteful over-treatment. It has metal
body with cushioned eyepiece, focus adjustment, and a rubber hand grip. A calibration
screwdriver, calibration fluid, a plastic pipette, optical cleaning cloth, and a rugged carrying
case are included.
1 each
Nu-Calgon Number
61301
ClenAir Number
GLY32
Glycol/Oil Transfer Pump
Heavy-duty pump designed to transfer Freez-Kontr’l®, Freez-Therm®, or oil products (up to
1000 sus) from Nu-Calgon supplied 55 gallon drums to their application.
1 each
24
4817-0
Winter Treat®
Multi-treatment product for hot water and steam heating boilers and other closed water systems.
It emulsifies and cleans away rust and corrosion deposit sludge, as well as inhibits system corrosion,
foaming, surging, and lime scale. Typical use is one quart per 25 gallons of water.
1 quart bottle
1 gallon bottle
4390-32
4390-08
Ty-lon® B20
A liquid nitrite-borax corrosion inhibitor and dispersant for closed recirculating systems.
It combines corrosion inhibitors, a unique copolymer dispersant, and a color indicator to
facilitate leak detection, into a complete treatment for hot and chilled water closed systems
containing ferrous and non-ferrous metal components.
5 gallon pail
7537-05
Ty-lon® B14A
An all-in-one boiler treatment product that controls scale, corrosion, and condensate line
corrosion in low pressure, low make-up steam heating boilers where 90% or more of the
condensate is returned. It is chromate-free and contains a color indicator for visual determination
of treatment residual. Its balanced formulation provides an energy-efficient way of heating.
5 gallon pail
7519-05
System Cleaner
A liquid, heavy-duty industrial alkaline cleaner specifically formulated to emulsify and clean
equipment surfaces and pipe fouled by cutting oils, grease, lubricants, corrosion products,
and other debris.
5 gallon pail
4370-08
Water Test Kits
Bacteria Test Kit
Bromine/Chlorine Test Kit
Kit contains 10 agar paddle tests that are used to monitor bacterial
contamination in cooling tower and evaporative condenser water. Test
can be performed in a lab or on site. Each side of the paddle is coated
with TTC Agar, material that supports growth of most common bacteria.
Regular testing will detect and show when bacteria counts are rising.
1 each
4802-0
Kit measures free and combined halogen (chlorine, bromine), and
it should be used to support treatment with Bromicide Tablets.
Residual can be expressed as 0.2 ppm or 0.5 ppm of free halogens.
Dropper technique is used.
Complete Test Kit
Nitrite Test Kit
The complete test kit for cooling water and boiler water application
testing. In addition to pH, this kit also provides tests for obtaining
alkalinity, nitrite, hardness, sulfite, and chloride levels.
Used for testing treatment residual of Ty-Ion B20 and Ty-Ion B14A. It is
a cerric ammonium nitrate (can) titration method, and it can be used
in systems containing glycol. Each drop equals 40 ppm of nitrite.
1 each
W017-0
1 each
1 each
4803-0
4797-0
No. 89A Test Kit
Organic Phosphonate Test Kit
No. 89A Test Kit contains tests for determining hardness, pH,
chloride and alkalinity, as well as treatment residual tests for Ty-Ion
C70, Cal-Treat 233, No. 340 Liquid Scale Inhibitor, and Ty-Ion B20.
Used to determine the treatment residual of No. 340 Liquid Scale
Inhibitor, Ty-Ion C70, and Cal-Treat 233.
1 each
1 each
4804-0
4798-2
Visit us at www.nucalgon.com or call 1-800-554-5499
25
Closed Systems & Steam Boilers
Closed Systems & Steam Boilers
Water Treatment
Scale Removal
Neutralized
Working
Strength
pH Color Indicator
Nu-Calgon’s exclusive “built-in” pH color
indicator tells you when to add more
acid, and it lets you see when the system
is clean. At working strength, the acid
cleaning solution is green or light blue.
When the acid solution is neutralized
and is no longer working, the solution
turns purple and more acid must then
be added. The system is clean when the
green color is retained for 20-45 minutes.
Competitive
Product with
Dangerous Foam
Nu-Calgon
Low-Foaming
Liquid Scale Dissolver
Low-Foaming Performance
To demonstrate its greater low-foam
property, Liquid Scale Dissolver was
added to a beaker containing lime
scale. A leading competitive liquid
product was added to another beaker
containing an equal amount of lime
scale. See the difference! When cleaning
towers and evaporator condensers,
low-foam is the preferred approach
as high foam is dangerous to both
personnel and surroundings.
Liquid Scale Dissolver
A hydrochloric (muriatic) acid formulated to remove calcium scales from cooling towers and other water-cooled equipment. It contains
low-foaming corrosion inhibitors and a built-in pH color indicator to let you know when the acid has been neutralized. pH test paper
is also included. USDA approved.
1 gallon bottle
5 gallon pail
55 gallon drum
4330-08
4330-05
4330-01
Eco-Lyme®
Eco-Lyme is a new chemistry for the HVACR market that provides a unique blend of
performance with a desired eco-profile. The product is specially formulated to achieve
descaling behavior of competing hydrochloric acid-based chemistry descalers. However,
the active ingredient is substantially safer on equipment metals. Eco-Lyme is ideal for
stainless steel construction to eliminate potential issues of localized corrosion/pitting
caused by repeated use of hydrochloric acid. Eco-Lyme is odorless, making it safer to use in
the field. NSF registered.
1 gallon bottle
5 gallon pail
55 gallon drum
4167-08
4167-05
4167-01
Season Start® “Imperial Grade” Scale Remover
A powdered sulfamic acid formulation that contains the best inhibitors available for
protecting all metals, including galvanized metal. It is the best and the safest dry acid
cleaner available. It contains a built-in pH color indicator to let you know when the acid
solution has been neutralized as well as wetting and anti-foaming agents. USDA approved.
10 lb. container
50 lb. pail
4360-88
4360-84
Initial Dosage Recommendation
26
Tons of Horsepower
Liquid Scale Dissolver
Eco-Lyme
Season Start
10
2 gallons
4 gallons
10 lbs.
30
5 gallons
10 gallons
30 lbs.
50
10 gallons
20 gallons
50 lbs.
90
15 gallons
30 gallons
75 lbs.
Vital-Flo® Tankless Water Heater Descaler Kit
The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling
tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long
hoses with 3/4˝ female hose threaded assemblies, formulated descaler solution packaged
in a lidded 4 gallon chemical resistant container. The solution is also available separately.
NSF registered.
Vital-Flo kit
Vital-Flo descaler solution
4387-01
4387-02
Feeding Equipment
No. 31-TX1 Acid Pump
Compact submersible pump designed for circulating strong acids and cleaning solutions. All
parts are constructed of acid-resistant materials.
1 each
4603-0
HK-31 Hose Kit
An accessory item available for use with the No. 31-TX Acid Pump. Kit includes two 1/2 inch
tubing adapters, two 10 foot sections of 1/2 inch clear plastic tubing and three hose clamps.
1 each
4604-0
Scale Prevention
Season Treat (6R Micromet®)
This patented Micromet® Plate product is contained in a unique flow-through package. The
package design makes it simple to treat small cooling towers and evaporative condensers.
Simply unwrap the package and place it in the sump. One canister treats up to 10 tons for scale
(5 tons for corrosion) for five to six months.
1 canister
4364-88
Ty-Ion® C70
An all-organic liquid scale, deposit, and corrosion inhibitor for use in open recirculating cooling
water systems, evaporative condensers, and air washer systems. This treatment program is
particularly effective in preventing scale deposits in systems that utilize make-up water with
high scaling potentials.
5 gallon pail
15 gallon pail
55 gallon drum
7597-05
7597-P3
7597-01
No. 340 Liquid Scale Inhibitor
An extremely concentrated scale inhibitor that is effective in hard, highly alkaline water. It is
very stable and does not form any sludge. It is most effective at treatment levels between 10
and 15 parts per million. A constant, accurate feed is accomplished with a Drip Feeder or CMS
Feed Pump. USDA approved.
1 gallon bottle
5 gallon pail
55 gallon drum
4340-08
4340-05
4340-01
To Inhibit Scale Formation
Tons of Refrigeration
or Horsepower
Containers of
Season Treat
Ty-lon C70
Required per Month
No. 340 Liquid Scale Inhibitor
Required per Month
Bleed-off for Most
Scale-forming Waters
10
1
1/4 gallon
1/4 gallon
1/8 gpm
30
3
2/3 gallon
1/2 gallon
1/3 gpm
50
5
1 gallon
3/4 gallon
1/2 gpm
100
---
2 gallons
1 1/2 gallons
1 gpm
120
---
2 1/2 gallons
2 gallons
1 1/4 gpm
150
---
3 gallons
2 1/2 gallons
1 1/2 gpm
Visit us at www.nucalgon.com or call 1-800-554-5499
27
Water Treatment
Water Heater Scale Removal
Water Treatment
Corrosion Prevention
Cal-Treat® No. 233
A liquid formulation that is used for controlling severe corrosion in evaporative condensers
and cooling tower systems. It is based upon a synergistic formulation of zinc, molybdate, and
organic phosphonate. Provides superior corrosion control and inhibits scale accumulation.
5 gallon pail
4149-05
To Control Corrosion
Cal-Treat No. 233 Required per Month
Bleed-off for Most Corrosive Waters
Capacity of System in Tons of Horsepower
1/3 gallon
1/10 gpm
10
1 gallon
1/4 gpm
30
2 gallons
3/8 gpm
50
3 gallons
1/2 gpm
90
Algae Prevention
No. 85 Algaecide
No. 85 Algaecide is a polymeric, cationic biocide that has been developed for controlling
biological growth in equipment. It is an EPA registered product to kill algae, bacteria, and
fungi in recirculating water systems, industrial air washing systems, and closed systems.
1 gallon bottle
4108-08
Bromicide Tablets
A chlorine-bromine donating organic compound in tablet form. It slowly releases powerful
oxidizing hypohalous acids, which prevent algae and slime bacteria fouling in open recirculating
cooling water systems and evaporative coolers. It also has the capability of breaking up and
removing existing biological mass from system surfaces. USDA approved and EPA registered.
50 lb. pail
4109-M9
To Kill Algae or Slime Growth
Tons of Refrigeration or Horsepower
Gallons of No. 85 Algaecide per Month
Number of No. 90 Bromicide Tablets
for an Average System
10
1/6 gallon
5
30
1/3 gallon
15
50
1/2 gallon
25
90
2/3 gallon
45
Other Water Treatment Products
Humidi-Pro™
Humidi-Pro is designed for humidifiers using up to 25 gallons per day and will inhibit scale for
one season. Install Humidi-Pro on the water line that supplies water directly to the humidifier.
1 each
4190-02
pH-Treat™
pH-Treat is an in-line treatment product specifically for the treatment of the acidic nature
of the condensate water produced by today’s high efficiency furnaces. Includes fitting kit
for easy installation.
1 each
28
4720-06
Evap-Treat®
Used in evaporative coolers or “swamp coolers” to prevent scale and corrosion. Place it in the
cooler sump and it will last all season long, thereby increasing pad life. Utilizes 6R Micromet®,
a slow dissolving polyphosphate.
1 each (coolers up to 6,500 cfm)
1 each (coolers up to 10,000 cfm)
4173-04
4173-06
Water Sample Bottles
The proper way to treat a cooling tower, closed loop system, or ice machine is to have the
supply or makeup water tested. Nu-Calgon provides this valuable service for free and will
analyze the water and recommend effective treatment. These bottles can also be used to
send in glycol samples to test freeze points.
1 each (3 bottles)
4995-0
No. 215 and No. 1075 Drip Feeders
Used for feeding No. 340 Liquid Scale Inhibitor, Cal-Treat 233, Ty-Ion C70 and No. 85
Algaecide. Calibrated at the factory to ensure accurate feeding. Provides the benefits of
continuous treatment for small systems without the high cost usually associated with
automatic feeding equipment.
No. 215 Drip Feeder
No. 1075 Drip Feeder
4669-W3
4670-W3
Jug Holders
These should be used when drip feeding any of Nu-Calgon’s liquid water treatment products.
Once secured to the cooling tower or evaporative condenser, they will hold the 1 or 5 gallon
containers in the proper position.
1 gallon holder
5 gallon holder
4606-0
4607-0
CMS III and CMS-IV Cooling Tower Monitor System
For monitoring conditions in cooling towers and evaporative condensers. Provides subsequent
bleed-off and chemical feed. It features a combination monitor and pump engineered into
one-piece digital equipment. Complete system includes a solenoid valve.
CMS III
CMS IV
4608-0
4608-4
No. 20L and No. 100L Feeders
Steel tanks suitable for pressures up to 150 psi and temperatures up to 212º F. Uses 3/4 inch
FNPT connections for installing on bypass to any size line. Use No. 20L Feeder for initial charges
up to 20 pounds (or 2 gallons). Use No. 100L Feeder for initial charges up to 100 pounds (or 10
gallons). Inlet/outlet strainers not included.
No. 20L Feeder
No. 100L Feeder
4628-0
4650-0
Conductivity Meter
A handheld conductivity meter with built-in cell and automatic temperature compensation.
It has an easy-to-read digital meter (in micromhos, 0-10,000) and dual point calibrations.
1 each
4812-0
Visit us at www.nucalgon.com or call 1-800-554-5499
29
Water Treatment
Other Water Treatment Products
Plumbing Products
Plumbing Products
Drain Solve
Ideal for condensate pan drains. Drain Solve saves time and money with its ease of use.
It eliminates application concerns associated with more reactive, fuming drain openers.
Simply pour it down the drain and let it work without fear of noxious fumes or reactions.
Does not contain sulfuric acid.
1 quart
1 gallon
4165-24
4165-08
Calci-Solve
Remove scale from lines and clear clogged drains easily and effectively with Calci-Solve. The
product includes a special inhibitor that coats the inside of the pipes with a protective film,
allowing the acid in Calci-Solve to quickly dissolve calcium, magnesium, sodium, lime, rust,
and other elements without harming pipes.
1 quart
1 gallon
4134-24
4134-08
UrinaKleen
Keep urinals free flowing with UrinaKleen. Use it to dissolve urinary salts, mineral scale, and
rust deposits which are found in urinals. It also attacks the primary source of odors.
1 quart
1 gallon
4590-24
4590-08
A/C Drain Sucker®
A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain
line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow
problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free
flowing drains, as well as all fittings and hoses for suction or pressure applications.
A/C Drain Sucker kit
PurCool Pan Strip - treats 3 tons - 6 mos.
Nu-Calgon Number
61308
61043
ClenAir Number
CADS1
1903D
Vital-Flo® Tankless Water Heater Descaler Kit
The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling
tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long hoses
with 3/4˝ female hose threaded assemblies, and a formulated descaler solution packaged in
a lidded four gallon chemical resistant container. The solution is also available separately.
NSF registered.
Vital-Flo kit
Vital-Flo descaler solution
30
4387-01
4387-02
Nickel-Safe Ice Machine Cleaner
The original Nickel-Safe Ice Machine Cleaner. It is a food-grade citric-phosphoric acid
product for removing scale deposits from ice machines having nickel-plated or tinplated evaporators, and it is acceptable for use in all ice machines containing nickel. It
mixes to form a green solution, which makes rinsing easier. USDA approved.
16 fluid ounce bottle
1 gallon bottle
4287-34
4287-08
Liquid Ice Machine Cleaner
Liquid Ice Machine Cleaner is a food-grade phosphoric acid that is fast acting, yet safe to use.
It has been formulated to remove scale deposits from ice machines and coffee urns. It does
not give off any harsh fumes or contain chlorine or chlorides that would attack stainless steel.
USDA approved. NSF registered.
8 fluid ounce bottle
1 gallon bottle
4207-47
4207-08
IMS-III Sanitizing Concentrate
IMS-III is an EPA registered sanitizing concentrate formulated to sanitize hard, non-porous
surfaces and to eliminate odors and slime growths. No rinsing is required when diluted to 1.6
ounces per gallon. Formulated for general use in ice machines, ice cream dispensing equipment,
and other food processing equipment.
16 fluid ounce bottle
4211-34
Ice Guard™ Plus
Ice Guard Plus contains advanced technology to prevent and control slime and other microbial
growths in ice machines. The technology utilizes known antimicrobial properties to inhibit microorganism reproduction that cause slime typically found in ice machines. One unit provides up to 6
months protection in machines producing up to 1200 lbs. of ice per day.
1 each
4209-07
6Rsp Micromet®
A slow dissolving phosphate specifically formulated for inhibiting scale in ice machines
and other equipment using low volumes of water. It is used in Nu-Calgon scale controlling
cartridges and requires replacement once every six months. Typical dosage is 8 ounces per 500
pounds of ice (50 gallons of water) a day.
50 lb. pail
4265-50
Visit us at www.nucalgon.com or call 1-800-554-5499
31
Water Filtration - Maintenance
Water Filtration - Maintenance
Water Filtration
Water Filtration - OEM Replacements
CFS Filtration System
A family of replacement cartridges and manifolds designed to service existing CUNO® CFS installations.
A cost-effective water filtration system for food service applications: ice machines, fountain beverages, steam ovens, and drinking water.
These systems offer manifold and sanitary quick-change cartridges to fit the existing CUNO CFS brand installations and can also support
new filtration installations. Nu-Plus CFS is the reliable choice for water filtration to prevent unwanted troubles caused by sediment, scale, or
taste and odor existing in CUNO installations.
Sediment – 5 micron
Sediment – 5 micron / phosphate
Carbon Block - .5 micron
Carbon Block - .5 micron / phosphate
Single Head
Twin Head
Triple Head
Twin Series
4623-10
4623-11
4623-12
4623-13
4623-01
4623-02
4623-03
4623-06
The CTL Series
The CTL Series contains a matching product for the Tri-Liminator Filtration System with
specifications that are nearly identical. For example, the CTL’s primary cartridge (C0070) will
replace both the K00070 and K00174 cartridges, and it has more scale control ability than either
of the Tri-Liminator cartridges. Part numbers are easily crossed over: CTL10 replaces the Tri-L10.
CTL 220
Prefilter
Primary cartridge - CG5-20S
4610-30
4621-43
9108-27
Water Filtration
Micro-Plus® & Micro-Carbon 4
The complete all-in-one treatment for ice machines, coffee urns and
brewers, humidifiers, steamers, etc. The Micro-Plus “in-line” filters
contain 6R Micromet® to control scale, high-grade activated carbon for
eliminating objectionable tastes and odors, and filter discs to remove
silt and sediment down to 20 microns. Available in four sizes with 1/4˝
FPT connections. When properly sized, each filter will last up to six
months. The Micro-Carbon 4 is available for removing objectionable
tastes and odors.
Micro-Plus 2
Micro-Plus 4
Micro-Plus 8
Micro-Plus 16
Micro-Carbon 4
4615-W3
4612-W3
4613-Y8
4614-Y8
4617-24
Application
Micro-Plus 2
Micro-Plus 4
Micro-Plus 8
Micro-Plus 16
Micro-Carbon 4
Water (per day)
12.5 gallons
25 gallons
50 gallons
100 gallons
50 gallons
Up to 125 lbs.
Up to 250 lbs.
Up to 500 lbs.
Up to 1000 lbs.
---
25 lbs.(1,250 cups)
50 lbs. (2,500 cups)
100 lbs. (5,000 cups)
200 lbs. (10,000 cups)
---
Ice (per day)
Coffee (per week)
32
NP Series Housings
These housings are designed to hold one of the NP Cartridges used to filter water for ice
machines, coffee urns, and other beverage equipment. The NP24DD and NP48DD Housings
fit specific NP24 or NP48 cartridges for controlling scale, sediment, or objectionable tastes
and odors. The NP24DD is equipped with 3/8˝ FPT connections and handles up to 4.0 gpm.
The NP48DD is equipped with 1/2˝ FPT connections and can handle flow rates up to 5.0
gpm.
NP24DD
NP48DD
4704-24
4714-24
6R Micromet®/Carbon Cartridge
A custom cartridge, combining 6R Micromet for scale-control and a carbon block for sediment
(10 microns), taste and odor control.
NP24PC
NP48PC
4706-87
4716-87
Carbon Block Cartridge
The NP24C Cartridge fits the NP24DD Housing while the NP48C fits the NP48DD. These carbon blocks
will remove most objectionable tastes and odors and are rated to remove particulate to 10 microns.
NP24C
NP48C
4701-87
4711-87
Sediment Cartridge
The NP24S (5˝) and the NP48S (10˝) are made from FDA-approved polypropylene construction
and filter to 5 microns. In addition, the 10˝ and 20˝ versions are available in bulk packaging.
NP24S
NP48S
20˝ bulk
4702-87
4712-87
4621-43
6R Micromet® Cartridge
The NP246R Micromet Cartridge contains 1 pound of 6R Micromet, and it fits the NP24DD
Housing. The NP486R Cartridge contains 2 pounds of 6R and fits the NP48DD Housing, with
10 micron filtration.
NP246R
NP486R
4705-87
4715-87
6R Micromet®/Sediment Cartridge
Another custom cartridge within the NP Series, consisting of polypropylene for filtration
(5 microns) and phosphate for scale-control.
NP48PS
4717-87
NP Series Brackets
Some installations may require two or three NP Series housings to meet more than one
specific water-related condition. This custom installation can be accomplished through the
use of one of the NP Series multi-housing brackets.
Two housing brackets
Three housing brackets
NP2BR
NP3BR
Problem to Solve
Cartridge Type
Sediment
“S” Cartridges
4
“C” Cartridges
4
“6R” Cartridges
4
“PC” Cartridges
4
“PS” Cartridges
4
Daily Capacities
Taste & Odor
Scale
“48’s”
1800 lbs. (200 gal.)
3600 lbs. (400 gal.)
1800 lbs. (200 gal.)
3600 lbs. (400 gal.)
4
900 lbs. (100 gal.)
1800 lbs. (200 gal.)
4
600 lbs. (65 gal.)
1200 lbs. (135 gal.)
4
4
“24’s”
4
Visit us at www.nucalgon.com or call 1-800-554-5499
550 lbs. (60 gal.)
33
Water Filtration -NP Series
Water Filtration - NP Series
Water Filtration - Nu-Plus® by Everpure®
Heads
QL3B Single System Head
Used with any Nu-Plus® E Series filters. Head includes a water shut-off
valve with mounting bracket and screws. (3/8˝ NPT)
1 each
4621-07
QC7I Single Head
Ideal for all Nu-Plus® E Series filters. Head includes a shut off, flushing
valve, and outlet pressure gauge on a box bracket design. (3/8˝ NPT)
1 each
4621-01
QC7I Twin Parallel Head
Dual filter head that is parallel plumbed for two Nu-Plus® E Series
filters, either mix or match. Head includes a shut off, flushing valve, and
outlet pressure gauge on a box bracket design. (3/4˝ NPT)
1 each
4621-02
QC7I Triple Parallel Head
Triple filter head parallel plumbed for three Nu-Plus® E Series filters.
Head includes a shut off, flushing valve, and outlet pressure gauge on
a box bracket design. (3/4˝ NPT)
1 each
4621-03
QC7I Quad Parallel Head
Quad filter head parallel plumbed for four Nu-Plus® E Series filters.
Head includes a shut off, flushing valve, and outlet pressure gauge on
a box bracket design. (3/4˝ NPT)
1 each
4621-04
*Everpure® is a trademark of Everpure, Inc., Westmont, IL.
34
MRS-20 Reverse Osmosis System
Complete mineral reduction water processing system that removes at least 90%+ of all
dissolved solids that cause scale build-up. The MRS-20 system removes taste and odor causing
contaminants as well as dirt and particles. The two-part design makes installation flexible.
It has no moving parts and requires no electrical power. System includes mineral reduction
processor, carbon filter cartridge, reverse osmosis cartridge, and storage tank. No monitoring
of grains per gallon is necessary.
MRS-20
9797-91
Kleensteam CT and Kleensteam II
Everpure’s second generation water treatment system for steam applications.
Kleensteam is a total system delivering high quality filtered water with scale inhibition as well
as deliming capabilities. The dual cartridge design provides enhanced performance for low and
high flow capacity steamers and flexibility for expanding to meet future needs. Kleensteam
also reduces chlorine-induced corrosion. It’s simple to install, operate, and maintain.
Kleensteam CT
Kleensteam II
1.67 gpm max. flow
2.5 gpm max. flow
9797-50
9797-21
Nu-Plus E Series by Everpure High Flow CSR Manifold with Prefilter
Utilizing the nu-MC2 or the nu-XC2 cartridges, this system provides premium quality water to
high flow fountain dispensers, coffee makers and ice machines. New and improved MicroPure II media inhibits the growth of bacteria. High Flow CSR reduces chlorine taste and odor
and other offensive contaminants that can adversely effect the taste of beverages. Precoat
submicron technology reduces dirt and particles as small as 1/2 micron and reduces health
contaminants such as cysts. Additionally, the SRX Housing inhibits scale when it is equipped
with scale-inhibiting IMF-10 ScaleSticks®.
10˝
20˝
High Flow CSR Manifold with Prefilter
Twin
Triple
9294-02
9294-03
9294-22
9294-23
Quad
9294-04
9294-24
Nu-Plus E Series by Everpure Coldrink/Insurice Systems
The Coldrink/Insurice manifolds can be used with any Nu-Plus by Everpure cartridges. i.e. the
MC2 or XC2 for carbonated beverages or i20002 or i40002 for ice machines. Utilizes the systems'
existing 10" or 20" pre-filter on a single, twin, triple, or quad manifold. Systems come with the
initial EC110 or EC210 pre-filter cartidge. Just purchase the appropriate Nu-Plus by Everpure
cartridge for your application.
10˝
20˝
Coldrink/Insurice Manifold with Prefilter
Single
Twin
Triple
9293-01
9293-02
9293-03
9293-21
9293-22
9293-23
Visit us at www.nucalgon.com or call 1-800-554-5499
Quad
9293-04
9293-24
35
Water Filtration - Nu-Plus® by Everpure®
Systems
Water Filtration - Nu-Plus® by Everpure®
Cartridges
nu-i20002 and nu-i40002
Reduces water-related ice machine problems caused by dirt, objectionable tastes and odor
and scale build-up. Pre-coat submicron filtration reduces particles as small as 1/2 micron along
with chlorine and other offensive contaminants. In addition, both cartridges use 6R Micromet®,
a highly acclaimed scale inhibitor that inhibits scale build-up caused by dissolved minerals. NSF
registered under NSF/ANSI Standards 42 and 53.
•
•
•
•
Pre-coat filtration with Micro-Pure® II antibacterial protection
Premier 6R Micromet scale control
Cyst and asbestos fibers reduction
Sanitary quick-change cartridge replacement
nu-i20002
4621-10
Capacity: 9,000 gallons • 750 lbs. for most cubers • 1,500 lbs. for most flakers
nu-i40002
4621-11
Capacity: 12,000 gallons • 1,000 lbs. for most cubers • 2,000 lbs. for most flakers
nu-MC2 and nu-XC2
Reduces chlorine taste, odor and other offensive contaminants that can adversely affect the
taste of fountain beverages. Pre-coat submicron filtration reduces particles as small as 1/2
micron, and it helps retain carbonation in drinks. NSF registered under NSF/ANSI Standards
42 and 53.
•
•
•
•
Pre-coat filtration with Micro-Pure® II antibacterial protection
Reduces objectionable tastes and odors
Cyst and asbestos fibers reduction
Sanitary quick-change cartridge replacement
nu-MC2
Capacity: 9,000 gallons
4621-20
nu-XC2
Capacity: 12,000 gallons
4621-21
BH2 and OCS2 Cartridge
•
•
•
•
•
•
Delivers premium quality water for ice and coffee applications
Designed for applications where the i20002 is too long
Precoat submicron particulate reduction
Inhibits scale formation
Taste and odor reduction
NSF registered under NSF/ANSI standards 42 and 53.
BH2
4621-12
Capacity: 3,000 gallons or 6,000 pots of coffee • 0.5 gpm max. flow
OCS2
9618-07
Capacity: 1,500 gallons or 3,000 pots of coffee • 0.5 gpm max. flow
OW200L and OW4Plus Cartridge
•
•
•
•
•
•
Ideal for office or residential water systems
Unique filter blend uses activated carbon to reduce chlorine taste, odor, and other
offensive contaminants
Reduces lead to below the Federal Action Level of 10 ppb
Precoat submicron technology reduces dirt and particles as small as 1/2 micron
Inhibits scale build-up in water-using appliances
NSF registered under NSF/ANSI standards 42 and 53
OW200L
Capacity: 480 gallons
9619-06
OW4PLUS
Capacity: 2,000 gallons
9635-06
*Everpure® is a trademark of Everpure, Inc., Westmont, IL.
36
4CB5, 7CB5, 4CB5-S, and nu-7CB5-S Cartridge
Carbon Block filter finely polishes water for high quality beverages and food applications.
NSF registered under NSF Standard 42.
• Problem-solving cartridge for high particulate or low flow water pressure areas • Taste and odor, chlorine reduction
• Particulate reduction to 5 micron
• 4CB5-S, and nu-7CB5-S cartridges control scale
4CB5
Capacity: 6,000 gallons
4621-32
7CB5
Capacity: 10,000 gallons
9618-16
4CB5-S
Capacity: 6,000 gallons
4621-31
nu-7CB5-S
Capacity: 10,000 gallons
4621-30
4FC5, 7FC5, 4FC5-S, and 7FC5-S Cartridge
New Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial
growth. Balanced for optimum performance in varying water qualities. Helps retain the
drink’s carbonation.
• Increased capacity 25,000 gallons
• 2.5 gpm flow rate
• Taste and odor reduction
• 5 micron rating
• Particulate reduction
• Scale inhibition (4FC5-S and 7FC5-S)
• NSF standards 42 and 53
4FC5
Capacity: 15,000 gallons
9693-21
7FC5
Capacity: 25,000 gallons
9693-61
4FC5-S
Capacity: 15,000 gallons
9693-31
7FC5-S
Capacity: 25,000 gallons
9693-71
4FC, 7FC, 4FC-S, and 7FC-S Cartridge
New Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial
growth. Balanced for optimum performance in varying water qualities. Improves the taste of
fountain drinks and helps retain the drink’s carbonation.
• Taste and odor reduction
• 0.5 micron rating
• Particulate reduction
• NSF standards 42 and 53
• 2.5 gpm flow rate
• Scale inhibition (4FC-S, and 7FC-S only)
4FC
Capacity: 15,000 gallons
7FC
Capacity: 25,000 gallons
9692-21
4FC-S
Capacity: 15,000 gallons
7FC-S
Capacity: 25,000 gallons
9692-31
9692-61
9692-71
Visit us at www.nucalgon.com or call 1-800-554-5499
37
Water Filtration - Nu-Plus® by Everpure®
Cartridges
Water Filtration - Nu-Plus® by Everpure®
Cartridges
4SI and 7SI Cartridge
Specially designed for ice machines. This cartridge does not include carbon, which allows
for complicance with ASHRAE Standard 188. The cartridge reduces sediment and particulate
down to 1/2 micron and reduces cyst and Giardia. The filter allows chlorine to pass through,
which helps reduce slime and bacteria growth inside the ice machine and ice bin. Ideal for
food service operations where baking of bread and pastries is done on-site.
• Scale inhibition
• 0.5 micron rating
• Particulate reduction
• NSF standards 42
• Cyst reduction
4SI
Capacity: 15,000 gallons • 2.0 gpm flow rate
7SI
Capacity: 25,000 gallons • 3.5 gpm flow rate
9606-51
9606-01
7CLM Cartridge
Reduces chloramines, chlorine taste and odor and other offensive contaminants that can
adversely affect the taste of beverages. The cartridge reduces particles down to 1/2 micron
and reduces cysts and Giardia. Improves the taste of fountain beverages and helps retain the
drink’s carbonation. NSF registered.
• Chloramine reduction
• Cyst reduction
• Chlorine reduction
• Particulate reduction
7CLM
9693-01
Capacity: 3,600 gallons at 1.7 gpm, 5,500 gallons at 1.33 gpm
7SO Softening Cartridge
A softening cartridge that reduces scale-forming minerals like calcium and magnesium in
hard water situations. It may be used on water having up to 30 grains hardness per gallon, at
flow rates of up to 1/2 gallons per minute. It is a sanitary quick change cartridge that makes
replacement easy. It should be used with an Everpure fine filter cartridge installed in a series
plumbed twin head.
7SO
Capacity: 2,000 grains • 0.5 gpm max. flow
9607-04
Replacement Cartridges for CUNO®
Nu-Plus® CU and Nu-Plus CU-S
The Nu-Plus E Series CU and CU-S cartridges are replacements that are compatible with the
CUNO Series CFS 8000 filter cartridges. Both incorporate a carbon block filter that reduces
objectionable tastes and odors as well as chlorine and other contaminates, providing high
quality beverage and ice. They also reduce extra fine dirt as small as 5 microns. Additionally,
the CU-S provides for the reduction of scale formation.
Nu-Plus CU
4622-20
Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow
Replaces CFS-8112, CFS-8720 & CFS-8812
Nu-Plus CU-S
4622-10
Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flow
Replaces CFS-8112S,CFS-8720S & CFS-8812S
*Everpure® is a trademark of Everpure, Inc., Westmont, IL.
*CUNO® is a trademark of 3M. This product is not manufactured, sponsored, or affiliated with 3M.
38
Nu-Plus® 10˝ and 20˝ Coarse Prefilters
A 10˝ and 20˝ clear housing, each including a 10˝ and 20˝ replaceable prefilter cartridge.
Filters out larger dirt and rust particles, thereby extending the life of submicron and carbon
block filters.
E-10
E-20
4621-42
4621-44
Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-45
Nu-Plus® EC110 and EC210
A 10˝ and 20˝ 10-micron nominal filtration cartridge for filtering out larger dirt and rust
particles, extending the life of primary filters. For use in the E-10 and E-20 housings as well as
other 10˝ and 20˝ housings.
EC110 (10˝)
EC210 (20˝)
4621-41
4621-43
SRX Scale Inhibitor Feeder
A complete system for the control of scale in ice, coffee, steam, and combination applications. It
dispenses a controlled amount of HydroBlend™ compound, which provides for a more consistent
feed and longer life. The system includes a clear housing and one cartridge
1 each
4621-05
Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-06
Nu-Plus® IMF-7 and IMF-10
Ice Machine Feeder Scale inhibition cartridge. The translucent cartridge allows for easy visual
monitoring of the product’s usage. The larger IMF-10 will last longer or treat higher volumes
of water.
IMF-7
IMF-10
Replacement for AR-X 7˝ Housing
Replacement for SS-10 Scale Sticks
4621-13
4621-14
4JT Flushing/Sanitizing Cartridge
The preferred way to introduce ScaleKleen™ Scale Remover or other sanitizing solutions
(IMS-III) into all water-using equipment and vending machines. Fits into existing Everpure
heads. Eliminates the need for difficult component disassembly. Easy and convenient to
help you clean and maintain equipment. Approved by NAMA.
1 each
4621-00
ScaleKleen™ Scale Remover
Restores equipment to peak operating efficiency by removing scale build-up. Quickly removes
limescale from coffee brewers. Ideal for deliming steam and ware washing equipment. Great for
office coffee system (OCS) applications. Non-toxic, safe to skin and won’t burn clothing. Sewer
system disposable; can be poured down the drain. Use with 4JT Flushing/Sanitizing Cartridge.
7 ounce packets (24 per case)
2.2 lb. canister (4 per case)
39
4621-17
9798-35
Visit us at www.nucalgon.com or call 1-800-554-5499
39
Water Filtration - Nu-Plus® by Everpure®
Other Filtration Products
Nu-Calgon Seminars & Training Classes
Free Seminars and Training Classes
NATE training now online. Visit us at www.nucalgon.com.
Coil Cleaning: The Clean Coil Program is a comprehensive seminar dedicated to the safe and proper procedures to
clean evaporator and condenser coils. The program will help determine which cleaning method should be utilized
for a particular job based on the type and condition of the unit. NATE Recognition Classes: 1 hour Continuing
Education Accreditation
Ice Machine Treatment and Filtration: A complete guide to “Extending the Life of an Ice Machine.” The seminar
will answer the questions: why use a filter, what filter should be used, and how to keep the system clean, clear, and
running properly. It also addresses all of the water-related problems associated with ice machines. (1.5 hours)
Indoor Air Quality Management: The seminar covers the past, present and future of indoor air quality (IAQ). Topics
covered in the session: how poor IAQ impacts a business, common causes of poor IAQ, and how to prevent poor IAQ
from occurring. NATE Recognition Classes: 1 hour Continuing Education Accreditation
Nu-Calgon Product Line Review: The seminar provides an overview of all the major products that Nu-Calgon
offers. The presentation explores when and where to use certain products, as well as explains how using certain
products can save time and money. (2 hours)
Refrigeration Oils: An in-depth look at industry refrigeration oils (Mineral, Alkylbenzene, and POE) and when and
where to use them. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation
Total System Protection: A thorough look at why burnouts occur, how to prevent them and the proper way to flush a
system once a burnout occurs. The training will include acid testing and acid neutralization. NATE Recognition Classes:
1 hour Continuing Education Accreditation
Water Treatment: This seminar will cover the fundamentals of water treatment for cooling towers, evaporative
condensers, boilers, and chillers. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation
Winter Water Treatment: This program focuses on what a system needs prior to the winter season, including a
review of ethylene and propylene glycol, the proper treatments for hot/cold closed systems, and low make-up
steam systems. (1 hour)
Energy Savings with A/C Re-New: Learn about a revolutionary product for revitalizing and energizing A/C systems.
The seminar will explain how A/C Re-New will help reduce energy costs, improve cooling performance and reduce
the system noise. (1 hour)
Food Service Products for Ice & Beverage Filtration: A comprehensive look at the problems associated with ice
and beverage filtration as well as treatment options to solve these problems. We will cover products for ice makers,
coffee brewers, fountain beverage machines, steam ovens, drinking water, and more. (1 hour)
40
Serving the United States & Canada with the Finest
Direct Factory Sales Force in the HVACR Industry
1. Seattle, WA
11. Kansas City, MO
21. Ocala, FL
2. Northern CA
12. St. Paul - Minneapolis
22. Tampa, FL
3. Southern CA
13. St. Louis, MO
23. Miami, FL
4. Los Angeles, CA
14. Baton Rouge, LA
24. Raleigh, NC
5. San Diego, CA
15. Milwaukee, WI
25. Richmond, VA
6. Phoenix, AZ
16. Chicago, IL
26. Baltimore, MD
7. Denver, CO
17. Indianapolis, IN
27. Philadelphia, PA
8. San Antonio, TX
18. Columbus, OH
28. NYC/New Jersey
9. Dallas - Fort Worth
19. Birmingham, AL
29. Syracuse, NY
10. Houston, TX
20. Atlanta, GA
30. Boston, MA
St. Louis, MO (Hdq.)
Visit us at www.nucalgon.com or call 1-800-554-5499
41
Nu-Calgon
2008 Altom Court | St. Louis, MO 63146
phone: 800-554-5499 | fax: 800-221-6302
www.nucalgon.com
(416) 3-300 | Calgon is a licensed trade name.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement