milan milan zest

milan milan zest
Conforms to
ECE R44/04
milan
milan
zest
user guide
EXTREME HAZARD:
Parents should not under any
circumstances use this child
restraint on a passenger seat
equipped with an airbag.
IMPORTANT ! KEEP FOR FUTURE REFERENCE
FC7715A
1
safety warnings
PLEASE READ THOROUGHLY BEFORE COMMENCING INSTALLATION AS AN INCORRECT INSTALLATION COULD BE DANGEROUS.
DO NOT USE THIS CHILD SEAT IN PASSENGER SEATS EQUIPPED WITH AIRBAGS.
This child seat must only be installed in a forward facing position in passenger
seats.
Do not use on side facing or rear facing seats.
Never attempt to use this child seat without fastening it into the car as described in
these instructions.
Do not add to or modify the seat in any way, other than as described in these instructions.
It is recommended that this car seat should be changed when it has been subjected to violent stresses in an accident or has become badly worn.
Do not leave your child unattended in the seat at any time.
Ensure that no part of the seat is trapped in a door or folding seat. If your car has a
folding rear seat, ensure that it is correctly latched in the upright position.
Car interiors can become very hot when in direct sunlight, it is therefore recommended that the child seat is covered when not in use.This prevents components,
particularly those attached to the child seat, becoming hot and burning the child.
Luggage and other heavy or sharp objects should be secured in the car. Loose
objects are liable to cause injury in the event of an accident.
The safest seating position for a child car seat is on the rear seat of a vehicle.
2
getting to know your child seat
This seat is classified as: Group 2 for children weighing from 15kg to 25kg (4 - 6 years
approx.) - in a forward facing position. Group 3 for children weighing from 22kg to 36kg
(6 - 11 years approx.) - in a forward facing position.
CHILD SEAT FOR USE
BY CHILDREN
WEIGHING 15-25 kg
(GROUP 2)
2
CHILD SEAT FOR USE
BY CHILDREN
WEIGHING 22-36 kg
(GROUP 3)
3
fitting the milan and milan zest cover
Your seat cover may be supplied seperately to
the plastic shell. To fit the cover to the shell, start
first with the plastic base and base cover. From
the front, slide the cover onto the shell making
sure you slide the cover over the arms of the shell.
Using the elasticated edges, make sure you have
a tight fit.
1
2
4
Then fit the head support cover onto the plastic head rest ensuring that you first fit the elastic
strap around the bottom of the plastic seat back
(see diagram). Then fit the back cover to the plastic seat back. The seat covers are tailored to fit the
plastic shells so you should attain a tight fit, which
is secured with the elasticated edges.
Once the cover is fitted, refer to Section 9 to assemble the base and back units.
the type of approved seat belt you must have
DIAGONAL BELT
Your mothercare child seat can only be installed
forward facing using a lap and diagonal seat
belt in the front or in the rear passenger seats of
the car.
DO NOT INSTALL THIS CHILD SEAT WITH A LAP
BELT ONLY.
LAP BELT
5
DO NOT USE THIS CHILD SEAT IN PASSENGER
SEATS EQUIPPED WITH AIRBAGS
legal requirements
This child seat is approved to ECE R44.04 and is ONLY suitable for use with a 3 point
lap and diagonal seat belt, approved to UN/ECE Regulation No.16 or other equivalent
safety standards.
front seat
Anyone, especially children, travelling in the front seat of a car must be properly restrained. Children under three years must use a suitable approved restraint designed
for their weight.
rear seat
All adults and children must use seat belts or child restraints where they are fitted in
the rear of a car and are available for use. If the appropriate restraint is not available,
children from 3 years must wear an adult seat belt if available.
3
6
important notes
This user guide should be stored under the seat cover of the base.
When the child seat is not in use, it is recommended that it is fastened into the car
with a seat belt to avoid being thrown about in the event of an accident.
If you travel with passengers using both the front and rear seats, the lighter occupants should be in the rear seats and the heavier occupants in the front of the
vehicle. When a child is in the front seat, the lighter passenger should be behind the
child.
Do not allow the child seat to come into contact with corrosive substances e.g. battery acid.
7
fitting your child seat into your car
Group 2 - To set up for use from 15kg to 25kg
fig 1
Place the car seat in a vehicle seat with a lap and
shoulder belt system. WARNING: do not place the
car seat in a seating position that only provides
a lap belt (such as the center rear seat on many
vehicles).
Position the booster firmly against the vehicle
seat back.
Position the child with their back flat against the
seat back.
fig 2
Pull the vehicle lap and shoulder belt across the
front of child and fasten buckle. Position vehicle
lap belt under both armrests and adjust until a
snug fit.
Route the vehicle shoulder belt under the armrest
(as shown) and into the shoulder belt guide 1.
- The lap belt A must be low on the hips, contacting the thighs.
- The shoulder belt B must contact the chest and
be centred on the shoulder.
Raise or lower head rest 2 until vehicle shoulder
belt is on child’s shoulder.
4
7
fitting your child seat into your car
Group 3 - To set up for use from 22kg to 36kg
fig 1
fig 2
fig 3
The child seat can be used as a ‘booster seat’ for
children over 22kg by removing the back section
of the seat.
To remove seat back, place the car seat on the
floor. While holding the base, push the seat back
rearward and lift the back from the base.
Place the booster in a vehicle seat with a lap and
shoulder belt system. WARNING: do not place the
booster in a seating position that only provides
a lap belt (such as the center rear seat on many
vehicles).
Position the booster firmly against the vehicle
seat back.
Position the child with their back flat against vehicle seat back. Pull the vehicle lap and shoulder
belt across the front of child and fasten buckle.
Position vehicle lap belt under both armrests and
adjust until a snug fit. The shoulder (diagonal) belt
should be routed over the armrest and over the
child’s chest.
- The lap belt A must be low on the hips, contacting the thighs.
- The shoulder belt B must contact the chest and
be centred on the shoulder.
5
8
final checklist
However safe a child seat is, however well built it is, your childs’ safety depends on you.
Read this final checklist once you have fitted your child seat in your car.
Check that your child seat is secure before each journey.
Check that both the lap and diagonal sections of the vehicle seat belt are correctly
positioned.
REMEMBER: mis-using your child seat will reduce the protection and safety you
offer your child.
IF YOU ARE UNSURE ABOUT THE FIT OF YOUR CHILD SEAT, PLEASE VISIT YOUR LOCAL
MOTHERCARE STORE FOR ADVICE.
9
seat assembly and returning to high back configuration
TO ASSEMBLE THE SEAT AFTER YOU HAVE FITTED YOUR ZEST COVER FOLLOW
THE GUIDELINES BELOW.
AFTER YOU HAVE USED THE CHILD SEAT FOR AN OLDER CHILD (GROUP 3)
YOU MUST FOLLOW THE GUIDELINES BELOW WHEN RE-USING THE SEAT FOR
A YOUNGER CHILD (GROUP 2).
To install seat back: Place booster car seat base
on the floor or other firm surface. Holding seat
back slightly reclined, place tabs at bottom of
seat back into slots of seat base.
Push seat back into an upright position 1.
Press down firmly until wings on side of seat back
touch arms on seat base 2 and tabs fully engage
with slots in base.
6
10
care of your product
removing the fabric cover
The fabric cover can be removed from the seat. Release the elasticated edges of
the cover from the seat. Carefully remove the cover. Please refer to the sewn in label
for care instructions.
cleaning the seat
The plastic parts can be sponged with a mild detergent and warm water. Dry thoroughly before use.
11
accessories & replacement parts
Your child seat and its cover have been carefully designed, manufactured and tested
to the highest safety standards.
Do not put your child’s safety at risk by using without a seat cover. The seat cover
should not be replaced with any other than the one recommended by mothercare,
because the cover constitutes an integral part of the restraint performance.
The safety of this seat may be compromised by the use of accessories not approved
by mothercare. The replacement parts listed below are available for your product. In
the event that you require any of these parts, please contact your local mothercare
store or contact Customer Care on 08453 30 40 30.
Replacement Parts
Booster cover
Back cover
Head rest cover
12
customer care
If you have a problem with this product or require replacement parts, please contact
your nearest mothercare store or telephone the mothercare Customer Care Line on
08453 30 40 30.
Alternatively, write to: Customer Care
Mothercare Uk Ltd,
Cherry Tree Road
Watford, Herts,
WD24 6SH
7
notice
1. This is a ‘Universal’ child restraint. It is approved to Regulation No. 44.04 series of
amendments, for general use in vehicles and it will fit most, but not all car seats.
2. A correct fit is likely if the vehicle manufacturer has declared that the vehicle is
capable of accepting a ‘Universal’ child restraint for this age group.
3. This child restraint has been classified as ‘Universal’ under more stringent conditions than those which applied to earlier designs which do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.
5. Only suitable if the approved vehicles are fitted with 3 point static or retractor
safety belts approved to UN/ECE Regulation No.16 or other equivalent standards.
Made in France
for Mothercare,
Watford, Herts,
WD24 6SH
Issue 1 - 08-10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement