Panasonic | CF-AX2 | Operating instructions | Panasonic Toughbook CF-AX2

CF-AX2mk1(CPE02709YA)_OI_M.book Page 1 Wednesday, May 22, 2013 11:06 AM
OPERATING INSTRUCTIONS
Personal Computer
Model No.
CF-AX2 series
Introduction ...............................................10
Description of Parts .....................................12
First-time Operation .....................................14
Turning On / Turning Off ................................18
Switching the Display Mode ............................19
Useful Information
Handling and Maintenance .............................20
Installing Software .......................................25
Troubleshooting
Troubleshooting (Basic)
................................29
Getting Started
Getting Started
Useful Information
Safety Precautions ........................................2
Regulatory Information ....................................6
Troubleshooting
Read Me First
Read Me First
Contents
LIMITED USE LICENSE AGREEMENT ..............34
Specifications ............................................35
Standard Limited Warranty .............................39
Please read these instructions carefully before using this product, and save this manual for future use.
Appendix
Appendix
CF-AX2mk1(CPE02709YA)_OI_M.book Page 2 Wednesday, May 22, 2013 11:06 AM
Safety Precautions
To reduce the risk of injury, loss of life, electric shock, fire,
malfunction, and damage to equipment or property,
always observe the following safety precautions.
Explanation of symbol word panels
The following symbol word panels are used to classify and
describe the level of hazard, injury, and property damage
caused when the denotation is disregarded and improper
use is performed.
DANGER
Read Me First
Denotes a potential hazard that will result in serious
injury or death.
WARNING
Denotes a potential hazard that could result in serious
injury or death.
CAUTION
Denotes a hazard that could result in minor injury.
NOTICE
Denotes a hazard that could result in property damage.
The following symbols are used to classify and describe
the type of instructions to be observed.
These symbols are used to alert users to a specific operating procedure that must not be performed.
This symbol is used to alert users to a specific
operating procedure that must be followed in
order to operate the unit safety.
2
DANGER
Precautions on the battery pack
Do Not Throw the Battery Pack into a Fire or
Expose It to Excessive Heat
Generation of heat, ignition or rupture may result.
Do Not Insert Sharp Objects Into the Battery
Pack, Disassemble, or Modify It
Electrolyte leakage, generation of heat, ignition
or rupture may result.
Do Not Short the Positive (+) and Negative (-)
Contacts
Generation of heat, ignition or rupture may result.
• Do not place the battery pack together with
articles such as necklaces or hairpins when
carrying or storing.
Avoid Extreme Heat (Near the Fire, in Direct
Sunlight, for Example)
Electrolyte leakage, generation of heat, ignition
or rupture may result.
Do Not Apply Shocks to the Product by Dropping It, Applying Strong Pressure to It, etc.
Electrolyte leakage, generation of heat, ignition
or rupture of the battery may result.
• If this product is subjected to a strong impact,
stop using it immediately.
Do Not Charge the Battery Using Methods
Other Than Those Specified
If the battery is not charged using one of the
specified methods, electrolyte leakage, generation of heat, ignition or rupture may result.
When the Battery Pack Has Deteriorated,
Replace It With a New One
Continued use of a damaged battery pack may
result in heat generation, ignition or battery rupture.
Do Not Use with Any Other Product
The battery pack is rechargeable and was
intended for the specified product. If it is used
with a product other than the one for which it was
designed, electrolyte leakage, generation of
heat, ignition or rupture may result.
Do Not Use This Product with a Battery Pack
Other Than the One Specified
Use only the specified battery pack (Î page 14)
with your product. Use of battery packs other
than those manufactured and supplied by Panasonic may present a safety hazard (generation of
heat, ignition or rupture).
CF-AX2mk1(CPE02709YA)_OI_M.book Page 3 Wednesday, May 22, 2013 11:06 AM
DANGER
Precautions on the built-in battery
(for disposal)
Handling This Computer
Do Not Disassemble the Computer Except
When Disposing of It
Generation of heat, ignition or rupture of the
built-in bridge battery may result.
Do Not Apply Shocks to the Product by Dropping It, Applying Strong Pressure to It, etc
Electrolyte leakage, generation of heat, ignition
or rupture of the battery may result.
• If this product is subjected to a strong impact,
stop using it immediately.
When the Battery Has Deteriorated, Contact
Your Technical Support Office to Replace the
Battery
Continued use of a damaged battery may result
in heat generation, ignition or battery rupture.
Do Not Charge
Generation of heat, ignition or rupture may result.
WARNING
Do Not Use With Any Other Product
Generation of heat, ignition or rupture may result.
If a Malfunction or Trouble Occurs, Immediately Stop Use
Do Not Throw the Battery Into a Fire or
Expose It to Excessive Heat
Generation of heat, ignition or rupture may result.
If a Malfunction Occurs, Immediately Unplug
the AC Plug and the Battery Pack
• This product is damaged
• Foreign object inside this product
• Smoke emitted
• Unusual smell emitted
• Unusually hot
Continuing to use this product while any of the
above conditions are present may result in fire or
electric shock
• If a malfunction or trouble occurs, immediately
turn the power off and unplug the AC plug, and
then remove the battery pack. Then contact
your technical support office for repair.
Avoid Extreme Heat (Near the Fire, In Direct
Sunlight, for Example)
Generation of heat, ignition or rupture may result.
Do Not Short the Positive (+) and Negative (-) Contacts
Generation of heat, ignition or rupture may result.
Do Not Insert Sharp Objects Into the Battery,
Disassemble, or Modify It
Generation of heat, ignition or rupture may result.
Do Not Apply Shocks to the Computer by Dropping It, Applying Strong Pressure to It, etc.
Generation of heat, ignition or rupture may result.
WARNING
Precautions on the built-in battery
Do Not Charge the Battery Using Methods
Other Than Those Specified
If the battery is not charged using one of the specified methods, electrolyte leakage, generation of
heat, ignition or rupture of the battery may result.
Do Not Throw the Product Into a Fire or
Expose It to Excessive Heat
Generation of heat, ignition or rupture of the battery may result.
Avoid Extreme Heat (Near the Fire, In Direct
Sunlight, for Example)
Electrolyte leakage, generation of heat, ignition
or rupture of the battery may result.
Do Not Insert Sharp Objects Into the Battery
or Shocks, Disassemble, or Modify It
Electrolyte leakage, generation of heat, ignition
or rupture of the battery may result.
Read Me First
Handling the Built-in Battery
Do Not Touch This Product in a Thunderstorm If Connected with the AC Cable or Any
Other Cables
Electric shock may result.
Do Not Connect the AC Adaptor to a Power
Source Other Than a Standard Household AC
Outlet
Otherwise, a fire due to overheating may result.
Connecting to a DC/AC converter (inverter) may
damage the AC adaptor. On an airplane, only
connect the AC adaptor/charger to an AC outlet
specifically approved for such use.
Do Not Pull or Insert the AC Plug If Your
Hands Are Wet
Electric shock may result.
Clean Dust and Other Debris of the AC Plug
Regularly
If dust or other debris accumulates on the plug,
humidity, etc. may cause a defect in the insulation, which may result in a fire.
• Pull the plug, and wipe it with a dry cloth. Pull
the plug if the computer is not being used for a
long period of time.
3
CF-AX2mk1(CPE02709YA)_OI_M.book Page 4 Wednesday, May 22, 2013 11:06 AM
Read Me First
Safety Precautions
WARNING
CAUTION
Insert the AC Plug Completely
If the plug is not inserted completely, fire due to
overheating or electric shock may result.
• Do not use a damaged plug or loose AC outlet.
Do Not Place This Product on Unstable Surface
If balance is lost, this product may fall over or
drop, resulting in an injury.
Do Not Place Containers of Liquid or Metal
Objects on Top of This Product
If water or other liquid spills, or if paper clips,
coins, or foreign matter get inside this product,
fire or electric shock may result.
• If foreign matter has found its way inside,
immediately turn the power off and unplug the
AC plug and remove the battery pack. Then
contact your technical support office.
Avoid Stacking
If balance is lost, this product may fall over or
drop, resulting in an injury.
Do Not Disassemble This Product
You may receive an electric shock, or foreign
matter may enter and result in a fire.
Keep SD Memory Cards Away from Infants
and Small Children
Accidental swallowing will result in bodily injury.
• In the event of accidental swallowing, see a
doctor immediately.
Do Not Leave This Product in High Temperature Environment for a Long Period of Time
Leaving this product where it will be exposed to
extremely high temperatures such as near fire or
in direct sunlight may deform the cabinet and/or
cause trouble in the internal parts. Continued use
in such a resulting condition may lead to shortcircuiting or insulation defects, etc. which may in
turn lead to a fire or electric shocks.
Do Not Turn the Volume Up to Loud When
Using Headphones
Listening at high volumes that overstimulate the
ear for long periods of time may result in loss of
hearing.
Do Not Block the Ventilation Hole (Exhaust)
Using this product wrapped in cloth or on top of
bedding or a blanket can block the ventilation
hole and cause heat to build up inside, possibly
resulting in a fire.
Do Not Use This Product in Close Contact
With Your Body for a Long Period of Time
• Depending on the direction of the computer or
the way you hold the computer, your hands
and body will be more exposed to the hot wind.
• Using this product with exposing the skin to the
heat source of this product or AC adaptor for a
long period of time can cause a low-temperature burn.
Hold the Plug When Unplugging the AC Plug
Pulling on the cord may damage the cord, resulting in a fire or electric shock.
Do Not Do Anything That May Damage the AC
Cord, the AC Plug, or the AC Adaptor
Do not damage or modify the cord, place it near
hot tools, bend, twist, or pull it forcefully, place
heavy objects on it, or bundle it tightly. Continuing to use a damaged cord may result in fire,
short circuit, or electric shock.
Do Not Expose Yourself or Other Persons to
the Hot Wind from the Ventilation Hole
(Exhaust) For a Long Period of Time
Low-temperature burns may result.
Covering the ventilation hole (exhaust) with your
hand or other object can cause heat to build up
inside, possibly resulting in burns.
4
Do Not Keep This Product Wherever There is
a Lot of Water, Moisture, Steam, Dust, Oily
Vapors, etc.
Otherwise, possibly resulting in fire or electric
shock.
Do Not Move This Product While the AC Plug
Is Connected
The AC cord may be damaged, resulting in fire or
electric shock.
• If the AC cord is damaged, unplug the AC plug
immediately.
Use Only the Specified AC Adaptor With This
Product
Using an AC adaptor other than the one supplied
(supplied with the unit or one sold separately as
an accessory) may result in a fire.
Do Not Subject the AC Adaptor to Any Strong
Impact
Using the AC adaptor after a strong impact such
as being dropped may result in electric shock,
short circuit, or fire.
Take a Break of 10-15 Minutes Every Hour
Using this product for long periods of time may
have detrimental health effects on the eyes or
hands.
CAUTION
Do Not Connect a Telephone Line, or a Network Cable Other Than the One Specified,
into the LAN Port
If the LAN port is connected to a network such as
the ones listed below, a fire or electric shock may
result.
• Networks other than 1000BASE-T, 100BASETX or 10BASE-T
• Phone lines (IP phone (Internet Protocol Telephone), Telephone lines, internal phone lines
(on-premise switches), digital public phones,
etc.)
NOTICE
z Do not place the computer near a television or radio
receiver.
z Keep the computer away from magnets. Data stored
on the hard disk may be lost.
z This computer is not intended for the display of images
for use in medical diagnosis.
z This computer is not intended for a use with connection of
medical equipment for the purpose of medical diagnosis.
z Panasonic shall not be liable for loss of data or other
incidental or consequential damages resulting from the
use of this product.
z Do not touch the terminals on the battery pack. The
battery pack may no longer function properly if the
contacts are dirty or damaged.
z Do not expose the battery pack to water, or allow it to
become wet.
z If the battery pack will not be used for a long period of
time (a month or more), charge or discharge (use) the
battery pack until the remaining battery level becomes
30% to 40% and store it in a cool, dry place.
z This computer prevents overcharging of the battery by
recharging only when the remaining power is less than
approx. 95% of capacity.
z The battery pack is not charged when the computer is
first purchased. Be sure to charge it before using it for
the first time. When the AC adaptor is connected to the
computer, charging begins automatically.
z Should the battery leak and the fluid get into your
eyes, do not rub your eyes. Immediately flush your
eyes with clear water and see a doctor for medical
treatment as soon as possible.
z
z
z
z
z
ment is satisfied, charging begins automatically. Note
that the recharging time varies based on the usage
conditions. (Recharging takes longer than usual when
the temperature is 10 °C or below.)
If the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range.
This computer has a high temperature mode function
that prevents the degradation of the battery in high
temperature environments. (Î
Reference Manual “Battery Power”) A level corresponding to a 100%
charge for high temperature mode is approximately
equivalent to an 80% charge level for normal temperature mode.
The battery pack is a consumable item. If the amount
of time the computer can be run by using a particular
battery pack becomes dramatically shorter and
repeated recharging does not restore its performance,
the battery pack should be replaced with a new one.
When transporting a spare battery inside a package,
briefcase, etc., it is recommended that it be placed in a
plastic bag so that its contacts are protected.
Always power off the computer when it is not in use.
Leaving the computer on when the AC adaptor is not
connected will exhaust the remaining battery capacity.
Read Me First
CF-AX2mk1(CPE02709YA)_OI_M.book Page 5 Wednesday, May 22, 2013 11:06 AM
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR
AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR
TRAFFIC CONTROL EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS, MEDICAL
DEVICES OR ACCESSORIES*1, LIFE SUPPORT SYSTEMS OR OTHER EQUIPMENTS/DEVICES/SYSTEMS THAT ARE INVOLVED WITH ENSURING
HUMAN LIFE OR SAFETY. PANASONIC WILL NOT BE
RESPONSIBLE FOR ANY LIABILITY RESULTING
FROM THE USE OF THIS PRODUCT ARISING OUT
OF THE FOREGOING USES.
*1
As defined by the European Medical Device Directive
(MDD) 93/42/EEC.
Panasonic cannot guarantee any specifications, technologies, reliability, safety (e.g. Flammability/Smoke/
Toxicity/Radio Frequency Emission, etc) requirements
related to aviation standards that exceed the specifications of our COTS (Commercial-Off-The-Shelf) products.
NOTE
z The battery pack may become warm during recharging
or normal use. This is completely normal.
z Recharging will not commence if internal temperature
of the battery pack is outside of the allowable temperature range (0 °C to 50 °C). (Î
Reference Manual
“Battery Power”) Once the allowable range require-
5
CF-AX2mk1(CPE02709YA)_OI_M.book Page 6 Wednesday, May 22, 2013 11:06 AM
Regulatory Information
Information to the User
<Only for model with wireless LAN/Bluetooth>
Read Me First
This product and your Health
This product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this
product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile
phones.
Because this product operates within the guidelines found in radio frequency safety standards and recommendations,
we believe this product is safe for use by consumers. These standards and recommendations reflect the consensus of
the scientific community and result from deliberations of panels and committees of scientists who continually review and
interpret the extensive research literature.
In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
z Using this product on board of airplanes, or
z In any other environment where the risk of interference to other devices or services is perceived or identified as
harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment
(e.g. airports), you are encouraged to ask for authorization to use this product prior to turning on the product.
Regulatory Information
We are not responsible for any radio or television interference caused by unauthorized modification of this product. The
correction of interference caused by such unauthorized modification will be the responsibility of the user. We and its
authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from
failing to comply with these guidelines.
26-M-1
Regulations for Wireless LAN / Bluetooth
Country / Region
802.11a
802.11b/g
Bluetooth
Restricted to indoor use.
Austria, Belgium, Croatia, Cyprus,
Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Latvia, Lithuania, Luxembourg, Macedonia,
Malta, Netherlands, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, United Kingdom
Italy
Restricted to indoor use.
General authorization required if used
outside.
Turkey
Restricted to indoor use.
Prohibited within an 1 km radius from
the centre of the runway of the airports.
Norway
Restricted to indoor use.
General authorization required if used
outside of own premises.
Prohibited within a 20 km radius from
the centre of Ny-Ålesund.
z The latest version of “ERC RECOMMENDATION 70-03” by European Radiocommunications Committee and the
regulation in Turkey.
z Use only the antenna specified by Panasonic.
z Confirm the latest information to the radio regulation authorities.
40-E-1
6
CF-AX2mk1(CPE02709YA)_OI_M.book Page 7 Wednesday, May 22, 2013 11:06 AM
Lithium Battery
Lithium Battery!
This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only
be exchanged by authorized service personnel.
Warning!
A risk of explosion from incorrect installation or misapplication may possibly occur.
15-E-1
These symbols on the products, packaging, and/or accompanying documents mean that used electrical
and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection
points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
Read Me First
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard this product, please contact
your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.
53-E-1
Safety Precautions
<Only for model with wireless WAN>
The following safety precautions must be observed during all phases of the operation, usage, service or repair of any
Personal Computer or Handheld Computer incorporating wireless WAN modem. Manufacturers of the cellular terminal
are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of
design, manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply
with these precautions.
When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Personal Computer or Handheld Computer incorporating wireless WAN modem off, if instructed to do so by the
guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy.
The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by
interference from Personal Computer or Handheld Computer incorporating wireless WAN modem placed close
to the device. If in doubt about potential danger, contact the physician or the manufacturer of the device to verify
that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or
Handheld Computer incorporating wireless WAN modem away from the pacemaker, while it is on.
Switch off Personal Computer or Handheld Computer incorporating wireless WAN modem before boarding
an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions
may lead to the suspension or denial of cellular services to the offender, legal action, or both.
For details on usage of this unit in aircrafts please consult and follow instruction provided by the airline.
7
CF-AX2mk1(CPE02709YA)_OI_M.book Page 8 Wednesday, May 22, 2013 11:06 AM
Regulatory Information
Do not operate Personal Computer or Handheld Computer incorporating wireless WAN modem in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel
depots, chemical plants or where blasting operations are in progress. Operation of any electrical equipment
in potentially explosive atmospheres can constitute a safety hazard.
Your Personal Computer or Handheld Computer incorporating wireless WAN modem receives and transmits
radio frequency energy while switched on. Remember that interference can occur if it is used close to TV
sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always
switch off Personal Computer or Handheld Computer incorporating wireless WAN modem wherever forbidden, or when you suspect that it may cause interference or danger.
Read Me First
Road safety comes first! Do not use a Personal Computer or Handheld Computer incorporating wireless
WAN modem while driving a vehicle. Do not place the computer with wireless WAN modem in an area where
it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or
secure stowage area while driving.
Do not place the computer with wireless WAN modem in an area over an air bag or in the vicinity where an air
bag may deploy.
Air bags inflate with great force and if the computer with wireless WAN modem is placed in the air bag
deployment area may be propelled with great force and cause serious injury to occupants of the vehicle.
IMPORTANT!
Personal Computer or Handheld Computer incorporating wireless WAN modem operate using radio signals
and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely
solely upon any wireless device for essential communications, for example emergency calls.
Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating wireless WAN modem must be switched on and in a service area with adequate cellular signal strength.
Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g.
lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call.
Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Computer incorporating wireless WAN modem.
CAUTION:
Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions.
Interface Cable
Use of an interface cable longer than 3 m (9.84 feet) is
not recommended.
58-E-1
11-E-1
For Europe
<Only for model with a “CE ” mark on the bottom of the computer>
Declaration of Conformity (DoC)
“Hereby, Panasonic declares that this Personal Computer is in compliance with the essential
requirements and other relevant provisions of the Directive 1999/5/EC.”
Hint:
If you want to get a copy of the original DoC of our above mentioned products, please contact our web address:
http://www.doc.panasonic.de
Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Indication of the countries where WLAN is intended to be used:
AT BE BG CH CY CZ DE DK EE ES
FI FR GB GR HU IE IS IT LT LU
LV MT NL NO PL PT RO SE SI SK TR
18-25-E-0
This equipment requires minimum 20 cm spacing from all person’s body (excluding extremities of hands, wrist and
feet) in directions of the back and both sides of the LCD display during wireless modes of operation.If you use this
equipment in tablet mode when utilizing the wireless functionality, it requires a minimum 10 mm spacing from the body
(excluding extremities such as hands, wrist and feet) around the left and right hand sides of the LCD display.
60-E-1
8
CF-AX2mk1(CPE02709YA)_OI_M.book Page 9 Wednesday, May 22, 2013 11:06 AM
For UK
For your safety, please read the following text carefully.
This appliance is supplied with a molded three pin mains plug for your safety and convenience.
A 3 ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover
can be purchased from your local dealer.
If the fitted molded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug
cut off and disposed of safely.
There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket.
How to replace the fuse
The location of the fuse differs according to the type of AC mains plug (figures A and B).
Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.
Open the fuse cover with a screwdriver and replace the fuse and close or attach the fuse cover.
Figure A
Read Me First
ASA
Figure B
Fuse cover
8-E-1
For India
For the purpose of recycling to facilitate effective utilization of resources, please return this product to a
nearby authorized collection center, registered dismantler or recycler, or Panasonic service center when disposing of this product.
Please see the Panasonic website for further information on collection centers, etc.
http://www.panasonic.co.in/wps/portal/home
68-M-1
9
CF-AX2mk1(CPE02709YA)_OI_M.book Page 10 Wednesday, May 22, 2013 11:06 AM
Introduction
Thank you for purchasing this Panasonic product. For optimum performance and safety, please read these instructions
carefully.
In these instructions, the names are referred as follows.
indicates Windows® 8 Operating System.
indicates Windows® 7 Operating System.
„ Terms and illustrations in these instructions
CAUTION :
NOTE :
Enter :
Fn + F5 :
[Charm] -
:
Getting Started
(Start) - [All Programs]:
Î:
:
Conditions that may result in minor or moderate injury.
Useful and helpful information.
Press [Enter] key.
Press and hold [Fn] key, and then press [F5] key.
This illustration means to click
(Settings) in the Charm menu that appears when
you align the cursor to the top right (or bottom right) corner of the screen.
Click
(Start), and then click [All Programs].
Page in these Operating Instructions or in the Reference Manual.
Reference to the on-screen manuals.
Some illustrations are simplified to help your understanding and may look different from the actual unit.
If you do not log on as an administrator, you cannot use some functions or cannot display some screens.
Refer for the latest information about optional products to the catalogs, etc.
In these instructions, the names and terms are referred as follows.
• “ Windows® 8 Pro 64-bit” as “Windows” or “Windows 8”
• “Windows® 7 Professional 32-bit Service Pack 1” and “Windows® 7 Professional 64-bit Service Pack 1” as “Windows” or “Windows 7”
• DVD MULTI drive as “CD/DVD drive”
z For models with the flash memory drive, read the terms “hard disk” and “hard disk drive” as “flash memory drive”.
z
Screen messages are explained in [English (United States)].
(Depending on the language preference, some screen messages in these instructions are different from the actual
screen messages.)
z
z
z
z
„ Disclaimer
Computer specifications and manuals are subject to change without notice. Panasonic Corporation assumes no liability
for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.
„ Trademarks
Microsoft®, Windows® and the Windows logo are registered trademarks of Microsoft Corporation of the United States
and/or other countries.
Intel, Core, Centrino and PROSet are either registered trademarks or trademarks of Intel Corporation.
SDXC Logo is a trademark of SD-3C, LLC.
Adobe, the Adobe logo and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Bluetooth® is a registered trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Panasonic Corporation.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective
own companies.
10
CF-AX2mk1(CPE02709YA)_OI_M.book Page 11 Wednesday, May 22, 2013 11:06 AM
„ On-screen Manual
For further information about the computer, you can refer to the on-screen manual.
z Reference Manual
The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.
z Important Tips
The Important Tips will provide you with the battery information so that you can use the battery pack in the optimum
condition to obtain longer operation time.
To access the on-screen manuals, follow the steps below.
On the Start screen, click the [Manual Selector] tile, and select the on-screen manual.
Getting Started
Double-click [Manual Selector] on the desktop screen, and select the on-screen manual.
11
CF-AX2mk1(CPE02709YA)_OI_M.book Page 12 Wednesday, May 22, 2013 11:06 AM
Description of Parts
C
D
E
F
G
H
A
B
Getting Started
I
J
K
L
M
N
O
P
Q
R
A : Function key
Î
Reference Manual “Key Combinations”
B : Keyboard
C : Camera
Î
Reference Manual “Camera”
D : Windows button
Press this button to return to the Start screen, either in
the Laptop mode or Tablet mode.
E : Camera indicator
Lights when the built-in camera is operating.
F : Microphone
Inputs audio.
G : Ambient light sensor
The ambient light sensor is equipped with an automatic brightness adjustment function that adjusts the
display screen. (Î page 21)
H : LCD
I : Speaker
Î
Reference Manual “Key Combinations”
J : Security lock
A Kensington cable can be connected.
For further information, read the manual that comes
with the cable.
The security lock and cable is a theft prevention
device. Panasonic Corporation will bear no responsibility in the event of theft.
12
K : HDMI port
Î
Reference Manual “External Display”
L : USB 3.0 port
Î
Reference Manual “USB Devices”
M : USB 3.0 port (with continuous charging function)
Î
Reference Manual “USB Devices”
N : Volume adjustment buttons
– : Decreases volume
+ : Increases volume
O : Rotation lock button
Locks the screen display. (Only in the Tablet mode)
Î
Reference Manual “Display Rotation”
P : Smart Card Slot
<Only for model with Smart Card Slot>
Q : Power switch
Power status indicator
• Off: Power off/Hibernation
• Green: Power on
• Blinking green: Sleep
R : LED indicator
: Caps Lock
: HOLD mode
: Numeric key (NumLk)
: Battery status
Î
Reference Manual “Battery Power”
: Drive status
CF-AX2mk1(CPE02709YA)_OI_M.book Page 13 Wednesday, May 22, 2013 11:06 AM
H
I
Bottom
J
K
N
O
M
P
A
B
Q
C
D
E
F
G
L
Î
Reference Manual “Wireless WAN”
I : Bluetooth antenna
A : DC-IN jack
B : LAN port
Î
Reference Manual “Bluetooth”
J : Wireless LAN antenna
Î
Reference Manual “LAN”
C : VGA port
Î
Reference Manual “External Display”
D : SD Memory Card slot
: SD Memory Card status
(Blinking: During access)
Î
Reference Manual “SD Memory Card”
E : Microphone jack
A condenser microphone can be used. If other types of
microphones are used, audio input may not possible,
or malfunctions may occur as a result.
F : Headphone jack
You can connect headphones or amplified speakers.
When they are connected, audio from the internal
speaker is not heard.
G : Wireless switch
Î
Reference Manual “Disabling/Enabling Wireless
Communication”
Î
Reference Manual “Wireless LAN”
Î
Reference Manual “Bluetooth”
Î
Reference Manual “Wireless LAN”
K : Touch pad
L : HOLD button
On: HOLD mode activated
Off: HOLD mode deactivated
M : Rubber feet
Raise or lower the rubbers in accordance with the
usage conditions.
Do not raise them in the Tablet mode. Otherwise the
rubbers may break when changing to the Laptop
mode.
N : Battery pack
Î page 14
O : Battery latch
Automatically locked when the battery pack is correctly
secured. To unlock, slide the latches to the unlocked
position
.
P : Dust cover
Î “To clean the inside of the dust cover” (page 23)
Q : Ventilation hole (Exhaust)
Getting Started
H : Wireless WAN antenna
<Only for model with wireless WAN>
<Only for model with wireless WAN>
SIM card slot
SIM card slot is located in the battery compartment on the bottom of
the computer. Remove the battery pack to insert the SIM card.
SIM card
Bottom
Insert the SIM card into the SIM card slot with the contact side facing
upward and with the cut corner oriented as shown in the illustration.
Do not insert the SIM card upside down.
13
CF-AX2mk1(CPE02709YA)_OI_M.book Page 14 Wednesday, May 22, 2013 11:06 AM
First-time Operation
„ Preparation
A Check and identify the supplied accessories.
If you do not find the described accessories, contact Panasonic Technical Support.
• AC Adaptor . . . . . . . . . . . . . 1
• AC Cord . . . . . . . . . . . . . . . 1
• Battery Pack . . . . . . . . . . . . 1
Model No: CF-VZSU81EA
Model No: CF-AA6503A
• Soft Cloth . . . . . . . . . . . . . . . 1
• OPERATING INSTRUCTIONS (This book). . . . . . . . . . . . . . . . . . . . . . . . 1
B Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging (Î page 34).
1
Getting Started
1
Insert the battery pack.
A Turn the computer over.
B Slide the battery pack in parallel with the arrow direction.
C Insert the connector (A) into the receptacle on the computer, and push the
battery pack until it clicks into the secured position.
A
„ To remove the battery pack
While sliding the left and right latches to the unlocked position
pack, and pull it out.
, lift up the battery
CAUTION
z Make sure the battery pack is securely locked. If not, the battery pack may fall
when you carry the computer.
z Do not touch the terminals of the battery pack and the computer. Doing so can
make the terminals dirty or damaged, and may cause malfunction of the battery
pack and the computer.
NOTE
z Note that the computer consumes electricity even when the computer power is
off. For the period of time the fully charged battery will fully discharge, refer to
“Battery duration” (Î page 17).
z When the DC plug is not connected to the computer, disconnect the AC cord
from your AC wall outlet. Power is consumed simply by having the AC adaptor
plugged into an electrical outlet.
2
2
Open the display.
Hold the side of the computer with either of your hands and then hold and lift the (A)
part to open the display.
CAUTION
A
14
z Do not apply excessive pressure to the LCD. Do not open or close the display
holding the edge of the LCD segment.
z If the computer lifts when you are opening the display, hold the computer down
at its side, for example.
CF-AX2mk1(CPE02709YA)_OI_M.book Page 15 Wednesday, May 22, 2013 11:06 AM
3
DC IN 16 V
Connect your computer to a power outlet.
The battery charging starts automatically.
CAUTION
z Do not disconnect the AC adaptor and do not switch the wireless switch to on
until the first-time operation procedure is completed.
z When using the computer for the first time, do not connect any peripheral
device (including wired LAN cable) except the battery pack and AC adaptor.
z Handling the AC adaptor
Problems such as sudden voltage drops may arise during periods of thunder and
lightning. Since this could adversely affect your computer, an uninterruptible power
source (UPS) is highly recommended unless running from the battery pack alone.
4
Turn on the computer.
Open the display, and slide and hold the power switch
power status indicator (Î page 12) lights.
(Î page 12) until the
NOTE
z If the remaining charge of the built-in battery is less than 50%, performance of
the computer is degraded. We recommend you to charge the built-in battery for
20 minutes or more before starting setup of Windows.
5
<For MUI OS model>
Select language.
Select language and OS (32-bit or 64-bit).
CAUTION
Getting Started
3
z Carefully choose your language because you cannot change it later. If you set a
wrong language, you need to reinstall Windows.
A Select language on “Your display language” and click [Next].
Follow the on-screen instructions.
A Select language and OS (32bit or 64bit) on “Select OS” screen and click [OK].
The language setting will start by clicking [OK] on the confirmation screen.
You can return to the “Select OS” screen by clicking [Cancel].
The language and OS setting will be completed in about 15 minutes.
B When termination screen is displayed, click [OK] to turn off the computer.
C Turn on the computer.
6
Setup Windows.
Follow the on-screen instructions.
z The computer restarts several times. Do not touch the keyboard or touch pad,
and wait until the drive indicator
has turned off.
z After the computer is turned on, the screen remains black or unchanged for a
while, but this is not a malfunction. Wait for a moment until the Windows setup
screen appears.
z During setup of Windows, use the touch pad and clicking to move the cursor
and to click an item.
z Setup of Windows will take approximately
5/
20 minutes.
Go to the next step, confirming each message on the display.
z
Follow the steps below.
A When “Enable sensors” is displayed, click [Enable this sensor].
B When the [User Account Control] screen is displayed, click [Yes].
15
CF-AX2mk1(CPE02709YA)_OI_M.book Page 16 Wednesday, May 22, 2013 11:06 AM
First-time Operation
C At the [Display Rotation Tool] confirmation screen, click [Yes].
The computer restarts automatically, and the setting is enabled.
z
“Join a wireless network” screen may not appear.
You can set the Wireless Network after the setup of Windows is complete.
CAUTION
Getting Started
z Wait until the drive indicator
has turned off.
z You can change the user name, password, image and security setting after
setup of Windows.
z Remember your password. If you forget the password, you cannot use the Windows. Creating a password reset disk beforehand is recommended.
z Do not use the following words and characters for user name: CON, PRN, AUX,
CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, @, &, space. In particular, if you
create a user name (account name) that includes the “@” mark, a password will
be requested at the log-on screen, even if no password has been set. If you try to
log on without entering a password, “The user name or password is incorrect.”
may be displayed and you will not be able to
sign in /
log on to Windows (Î page 31).
z Use standard characters as a computer name: numbers 0 through 9, uppercase
and lowercase letters from A to Z, and the hyphen (-) character. If the error message “The computer name is not valid” appears, check if characters other than the
above are not entered. If the error message still remains on the display, set the key
entry mode to English (“EN”) and enter characters.
7
Set the time zone, and then set the date and time.
A Open the Control Panel.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Control Panel] under "Windows System".
B Click [Clock, Language, and Region] - [Date and Time].
C Click [Change time zone…].
D Select the time zone, then click [OK].
E Click [Change date and time…], then set the date and time.
8
Create the recovery disc.
If the recovery partition of the flash memory drive is damaged, for example, you can
use a recovery disc to reinstall the OS and restore its factory default condition. We
recommend creating a recovery disc before you begin using the computer.
Refer to Î
Reference Manual “Recovery Disc Creation Utility” about creating the disc.
NOTE
z PC Information Viewer
This computer periodically records the management information of the hard disk, etc. The maximum data volume for each
record is 1024 bytes.
This information is only used for estimating the cause when the hard disk goes down by any possibility. They are never
sent to outside via network nor used for any other purpose except for the purpose described the above.
To disable the function, add the check mark for [Disable the automatic save function for management information history]
in [Hard Disk Status] of PC Information Viewer, and click [OK].
(Î
Reference Manual “Checking the Computer’s Usage Status”)
z
<For MUI OS model>
In the default settings, a shortcut icon for Korean language is on the Desktop screen. You may delete the icon if not necessary.
„ Before using wireless function
A Slide the wireless switch to ON.
B Click [Charm] - [Change PC Settings] - [Wireless].
Set [Airplane mode] to [Off], and then;
set [Wi-Fi] in “Wireless device” to [On] (for wireless LAN).
set [Mobile broadband] in “Wireless device” to [On] (for wireless WAN).
set [Bluetooth] in “Wireless device” to [On] (for Bluetooth).
16
CF-AX2mk1(CPE02709YA)_OI_M.book Page 17 Wednesday, May 22, 2013 11:06 AM
B
C
D
E
F
Click
(Start) and right-click [Computer], then click [Manage].
z A standard user needs to enter an administrator password.
Click [Disk Management].
Right-click the partition for Windows (“c” drive in the default setting), and click [Shrink Volume].
z The partition size depends on the computer specifications.
Input the size in [Enter the amount of space to shrink in MB] and click [Shrink].
z You cannot input a larger number than the displayed size.
z To select [Reinstall to the System and OS partitions.] in installing OS (Î page 26),
<For localized OS model> 60 GB / <For MUI OS model> 70 GB
60 GB or more is necessary for [Total size
after shrink in MB].
Right-click [Unallocated] (the shrunk space in the step D) and click [New Simple Volume].
Follow the on-screen instructions to make the settings, and click [Finish].
Wait until formatting is completed.
NOTE
z You can create an additional partition using remaining unallocated space or newly creating unallocated space.
z To delete a partition, right-click the partition and click [Delete Volume] in the step C.
„ Battery duration
<For model without Smart Card Slot>
<For model with Smart Card Slot>
In sleep
Approx. 3.5 days
(Approx. 2.5 days with Wake Up from wired
LAN function activated)
Approx. 3 days
(Approx. 2 days with Wake Up from wired
LAN function activated)
In hibernation
Approx. 20 days
(Approx. 5 days with Wake Up from wired
LAN function activated)
Approx. 15 days
(Approx. 4 days with Wake Up from wired
LAN function activated)
When power is off
Approx. 20 days
Approx. 15 days
(Approx. 5 days with Power On by LAN func- (Approx. 4 days with Power On by LAN function activated)
tion activated)
Getting Started
„ To change the partition structure
You can shrink a part of an existing partition to create unallocated disk space, from which you can create a new partition.
This computer has a single partition as default setting.
A
Open “Computer”. Right-click [Computer], then click [Manage].
To open “Computer”, proceed as follows on the Start screen.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Computer] under “Windows System”.
The above table shows the battery duration while the USB port continuous charging function is not used.
The battery duration will slightly be longer if a LAN cable is not connected to the computer, even when Wake Up from
wired LAN function is activated.
„
<For MUI OS model>To select language
To select a language other than the one you have selected during the first-time operation, follow the steps below.
A Open the Control Panel.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Control Panel] under “Windows System”.
B Click [Clock, Language, and Region] - [Language] - [Add a language].
C Select a language, and then click [Add].Depending on the region, two or more languages are selectable. Click
[Open] and select the desired language, and then click [Add].
D Click [Option] for the language you want to use.
E Click [Make this the primary language].
F Click [Log off now].
G Sign in to the Windows.
17
CF-AX2mk1(CPE02709YA)_OI_M.book Page 18 Wednesday, May 22, 2013 11:06 AM
Turning On / Turning Off
Turning On
Slide and hold the power switch (Î page 12) until the power status indicator (Î page 12) lights.
NOTE
z Do not slide the power switch repeatedly.
z The computer will forcibly be turned off if you slide and hold the power switch for four seconds or longer.
z Once you turn off the computer, wait for ten seconds or more before you turn on the computer again.
z Do not perform the following operation until the hard disk drive indicator
• Connecting or disconnecting the AC adaptor
• Sliding the power switch
• Touching the keyboard, touch pad, tablet buttons or external mouse
• Closing the display
• Turn on/off the wireless switch
turns off.
Turning Off
Getting Started
A Shut down the computer.
1. Click [Charm] - [Settings].
2. Click [Power] - [Shut down].
Click
(Start) - [Shutdown].
B Close the display after the power indicator goes off completely.
NOTE
z
To turn off the computer, proceed as follows.
A Click [Charm] - [Change PC settings] - [General].
B Click [Restart now] under “Advanced startup”.
C Click [Turn off your PC].
When Starting Up/Shutting Down
Do not do the following
• Connecting or disconnecting the AC adaptor
• Sliding the power switch
• Touching the keyboard, or external mouse
• Closing the display
• Turn on/off the wireless switch
NOTE
z To conserve power, the following power saving methods are set at the time of purchase.
• The screen automatically turns off after :
10 minutes (when AC adaptor is connected) of inactivity
5 minutes (when operating on battery power) of inactivity
• The computer automatically enters sleep*1 after :
30 minutes /
20 minutes (when AC adaptor is connected) of inactivity
15 minutes (when operating on battery power) of inactivity
*1
18
Refer to
Reference Manual “Sleep and Hibernation Functions” about resuming from sleep.
CF-AX2mk1(CPE02709YA)_OI_M.book Page 19 Wednesday, May 22, 2013 11:06 AM
Switching the Display Mode
Laptop Mode and Tablet Mode
„ Laptop mode
• Operate the computer as a standard notebook PC using the keyboard, touchpad, and touchscreen.
• You can press the HOLD button to disable the keyboard and touchpad or only
the touchpad. (Î
Reference Manual “Using the Touch Pad”)
„ Tablet mode
Precautions during Switching
CAUTION
z Be careful when changing the display mode to prevent tangling the cables.
z If peripheral devices that may get in the way are connected, disconnect them before changing the display mode.
z When changing the display mode, unintentional operation of the keyboard and touchpad may occur. You can prevent such unintentional operations using the HOLD button. (Î
Reference Manual “Using the Touch Pad”)
Getting Started
• Operate the computer using the touchscreen.
• The keyboard and touchpad are disabled automatically.
• When the automatic rotation is enabled, the screen will rotate automatically based
on the angle in which you hold the computer.
Switching from Laptop Mode to Tablet Mode
Hold the display in the area circled in the illustration below, and fold it backward.
The computer will operate in laptop mode until the display mode finishes switching over to tablet mode.
19
CF-AX2mk1(CPE02709YA)_OI_M.book Page 20 Wednesday, May 22, 2013 11:06 AM
Handling and Maintenance
Operation Environment
z Place the computer on a flat stable surface not subject to shock, vibration, and danger of dropping. Do not place the
computer upright or turn it over. If the computer is exposed to an extremely strong impact, it may become damaged.
z Temperature:
Operation : 5 °C to 35 °C {41 °F to 95 °F}
Storage
: -20 °C to 60 °C {- 4 °F to 140 °F}
Humidity:
Operation : 30% to 80% RH (No condensation)
Storage
: 30%% to 90% RH (No condensation)
Even within the above temperature/humidity ranges, operation for a long time in extreme environments, smoking
nearby, or operation in places where oil is used or where there is a lot of dust will result in the product deterioration
and will shorten the product life.
• Be sure to use the computer in an environment with sufficient heat ventilation.
- Avoid using the computer on a highly heat retentive surfaces (e.g., rubber pads and blankets). If possible, use
the computer on surfaces that can dissipate heat, such as a steel desk.
- Do not cover the computer with towels, keyboard covers, etc., as this prevents heat dissipation.
- When using the computer, always keep the display open. (Note, however, that closing the display while the computer is in use does not cause generation of heat, ignition, or other malfunctions.)
- When using the computer in the Laptop mode, the areas around the ventilation holes become especially hot.
Do not hold the computer by these areas in the Laptop mode.
Do not use the computer on your lap for an extended periods of time.
z Do not place the computer in the following areas, otherwise the computer may be damaged.
• Near electronic equipment. Image distortion or noise may occur.
• In extremely high or low temperature.
z As the computer can become hot during operation, keep it away from items that are sensitive to heat.
Useful Information
Handling Cautions
20
This computer is designed to minimize shock to parts such as the LCD and the flash memory drive and equipped with a dripproof keyboard, but no warranty is provided against any trouble caused by shock. Be extremely careful when handling the computer.
z When carrying the computer:
• Turn off the computer.
• Remove all external devices, cables, and other protruding objects.
• Do not drop or hit the computer against solid objects.
• Do not leave the display open.
• Do not pick up or hold the computer by the display part.
• Do not put anything (e.g., a piece of paper) between the display
and keyboard.
z When flying on an airplane:
Correct
Incorrect
Incorrect
• Carry the computer with you, and never put it in checked baggage.
• Obey the airline’s instructions when using the computer on the airplane.
z When carrying a spare battery, put it in a plastic bag to protect its terminals.
z This computer contains a magnet and magnetic products at the locations
circled in the illustration at the right. Avoid leaving metallic object or magnetic media in contact with these areas.
z Do not place an object containing magnetic power to the (A) portions. Doing
so may cause the computer to detect mistakenly that the display is closed,
and as a result, the display may go out and the computer may enter sleep.
z The touch pad is designed to be used by finger tip. Do not place any object
on its surface and do not press down strongly with sharp-pointed or hard
objects that may leave marks (e.g., nails, pencils and ball point pens).
A
z Avoid any harmful substances such as oil from getting into the touch pad.
A
The cursor may not work correctly.
(Bottom)
z If the computer is being carried in a soft bag with the battery pack removed,
avoid undue pressure on the body of the computer in a crowded place, etc.,
as this may result in damage to the LCD.
CF-AX2mk1(CPE02709YA)_OI_M.book Page 21 Wednesday, May 22, 2013 11:06 AM
„ When the battery indicator does not light on
The battery indicator may not light on even if the AC adaptor and the battery pack are correctly connected to the computer, due to the following reasons.
z The AC adaptor’s protection function may be working. In this case, pull out the AC cord and wait for more than 1
minute before reconnecting the AC cord.
z When the battery is fully charged and the computer is not operating (i.e., it is turned off or in sleep mode), the power
supply from the AC adaptor stops and power consumption is inhibited (except when the Wake Up from LAN or the
Power On by LAN function is enabled). In this case, the indicator will light green upon connecting the AC adaptor,
but only for a moment.
„ If the computer becomes warm during usage
z When the screen is displayed on the External Display using Intel® Wireless Display Software, click
on the notifi-
cation area, click
, and click [Panasonic Power management (Better Heat Dispersion)].
• When changing to [Panasonic Power management (Better Heat Dispersion)], the following settings will change.
- Change to [High Speed] from [Standard] in [Fan control mode].
Rotation of the cooling fan will become faster and the computer can be cooled down. Note that the battery operating time will be shorter.
- Switch the screen saver to [Prohibited].
- Other setting changes such as the lowering of the internal LCD brightness.
• When you do not frequently use CPU or the rotation noise of the fan bothers you, set [Standard] or [Low Speed] in
[Fan control mode].
z If you are not using a wireless LAN, turn the wireless LAN off.
z Clean the inside of the dust cover once a month. (Î page 23)
Follow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction
manuals of the peripheral devices.
z Use the peripheral devices conforming to the computer’s specifications.
z Connect to the connectors in the correct direction.
z If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc.
z If screws are included, fasten them securely.
z Remove the cables when you carry the computer. Do not pull the cables forcibly.
„ Preventing your computer from unauthorized use via wireless LAN/Bluetooth/Wireless WAN
z Before using wireless LAN/Bluetooth/Wireless WAN, make the appropriate security settings such as data encryption.
„ Battery Recalibration
Useful Information
„ When using peripheral devices
z The battery recalibration may take a long time due to the large battery capacity. This is not a malfunction.
<When performing “Battery Recalibration” after shutting down Windows>
• Full charge: Approximately 4 hours (max.) (Approximately 3.5 hours (max.) for models with Smart Card slot) (with
CF-VZSU81EA)
• Complete discharge: Approximately 3 hours (max.) (Approximately 2.5 hours (max.) for models with Smart Card
slot) (with CF-VZSU81EA)
When performing “Battery Recalibration” without shutting down Windows, it may take more time to charge / discharge.
„ Sensors
This computer is equipped with four sensors (acceleration sensor, gyro sensor, magnetic sensor, ambient light sensor),
and you can use these sensors with any software that is compatible.
As the accuracy of each sensor output is dependent on the operating environment and other conditions, the results
should only be used as a reference.
The acceleration sensor, gyro sensor, and magnetic sensor are located under the keyboard. The detection results of
each sensor may vary depending on the display mode, how you are holding the computer, the application software you
are using, and other factors.
z Display rotation
When the computer is in the Tablet mode, and the automatic rotation is on, the built-in acceleration sensor detects
the computer’s inclination, and the screen display rotates automatically.
When an external display is connected, the display does not roatate.
21
CF-AX2mk1(CPE02709YA)_OI_M.book Page 22 Wednesday, May 22, 2013 11:06 AM
Handling and Maintenance
Note also that some application programs may not support the primary and secondary Portrait angle display. For
such programs, use the computer in primary or secondary Landscape angle.
z Automatic brightness adjustment
The computer is equipped with an automatic brightness adjustment function that adjusts the display screen based
on the ambient light sensor. You can configure the automatic adjustment function as follows.
A Click [Charm] -
- [Change PC Settings] - [General] - [Screen] - [Adjust my screen brightness automatically].
Click
(Start) - [Control Panel] - [Hardware and Sound] - [Power Option].
Click [Change plan settings] for the power plan currently used.
Click [Change advanced power settings] and double-click [Display].
Double-click [Enable adaptive brightness], make necessary settings, and click [OK].
Set each item to ON, and the brightness of the screen display will adjust automatically.
The ambient light sensor is located at the top of LCD.
The ambient light cannot be detected properly if this area is obstructed or dirty.
A
B
C
D
Useful Information
z Magnetic sensor
The magnetic sensor on the computer operates by detecting geomagnetism. Therefore, the magnetic sensor may
not function properly and it readings may be inaccurate, especially in the following environments.
• Inside or near steel structures such as buildings or bridges
• Inside or near automobiles, or near train power lines
• Near metallic furniture or appliances
• When the AC adaptor or other peripheral devices are brought closer to the computer
• Near magnets, speakers, or other objects with strong magnetic fields
The magnetic directions indicated by the magnetic sensor may not be accurate immediately after purchase or in
environments with poor magnetic fields.
In such cases, turn on the computer and move it as follows.
A Hold the computer so that its keyboard side is facing the ground and level.
B While keeping the computer level, rotate it 90 degrees or more clockwise.
C Tilt the computer 90 degrees or more so that the side of the computer tilts down.
CAUTION
CAUTION
z Hold the computer firmly when moving it. Strong shocks from dropping the computer may result in damage.
Maintenance
If drops of water or other stains get on the surface of the LCD panel, wipe them off immediately. Failure to do so may
result in staining.
To clean the LCD panel
Use the soft cloth included with the computer. (For further information, refer to “Suggestions About Cleaning the LCD
Surface” Î
Reference Manual “Screen Input Operation”.)
To clean the touch pad
Wipe lightly with a gauze or other dry, soft cloth.
To clean areas other than the LCD panel and touch pad
Wet a soft cloth with water or a diluted kitchen cleanser (neutral), wring the cloth out thoroughly, and wipe the dirty area
gently. Using a detergent other than a neutral kitchen cleanser (e.g., a weak alkali cleanser) may adversely affect
painted surfaces.
CAUTION
z Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc.
Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to
the surface.
22
CF-AX2mk1(CPE02709YA)_OI_M.book Page 23 Wednesday, May 22, 2013 11:06 AM
z Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause
malfunction or damage.
To clean the inside of the dust cover
Clean the inside of the dust cover once a month.
A Turn off the computer, and disconnect the AC adaptor.
B Close the display, and turn the computer over.
C Remove the battery pack.
D Remove the screw (B), and remove the dust cover (C) in the direction of the
arrow.
E Clean the inside of the dust cover.
F After cleaning, reset the dust cover (C), and secure the screw (B).
C
B
CAUTION
z If dust is piled up inside the dust cover and hard to remove, use an electric cleaner.
Be careful not to inhale dust.
z Make sure no water or other liquid spills inside the dust cover, and pay attention not to drop the screw inside the dust
cover.
„ Preparation
z Remove all peripherals (SD memory card etc.).
z Erase the stored data. (Î
Reference Manual “Hard Disk Data Erase Utility”)
CAUTION
z Never disassemble the computer except before disposal.
z Refer to page 3 for precautions when disposing of the computer.
Useful Information
Dispose of Computer
1. Turn off the computer.
z Do not use sleep/hibernation.
2. While connecting the battery pack, disconnect the AC adaptor.
3. While pressing the HOLD button, slide the power switch for more than five seconds.
The built-in battery's power output stops.
4. Turn over the computer, and remove the battery pack.
23
CF-AX2mk1(CPE02709YA)_OI_M.book Page 24 Wednesday, May 22, 2013 11:06 AM
Handling and Maintenance
5. Remove the screws (19), except the one circled in the illustration, and
remove the cover.
Cover
Useful Information
6. Remove the tape that secures the cords, and move the built-in battery as shown in
the illustration. (Illustration: models without Smart Card slot)
Tape
Built-in battery
7. Disconnect the connector, and remove the built-in battery. (Illustration: models
without Smart Card slot)
Connector
Built-in battery
24
CF-AX2mk1(CPE02709YA)_OI_M.book Page 25 Wednesday, May 22, 2013 11:06 AM
Installing Software
Installing software will return the computer to the default condition. When you install the software, the hard disk data
will be erased.
Back up important data to other media or an external hard disk before installation.
CAUTION
z Do not delete the Recovery Partition on the hard disk. The disk space in the partition is not available to store data.
To check the Recovery Partition, perform the following methods.
A
Open “Computer”. Right-click [Computer], then click [Manage].
To open “Computer”, proceed as follows on the Start screen.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Computer] under “Windows System”.
Click
(Start) and right-click [Computer], then click [Manage].
z A standard user needs to enter an administrator password.
B Click [Disk Management].
„ Hard Disk Recovery
You can reinstall the OS that was pre-installed at the time of purchase (Windows 8 or Windows 7).
Preparation
z Change to the laptop mode.
z Remove all peripherals.
z Connect the AC adaptor and do not remove it until installation is complete.
Start the Setup Utility.
A Click [Charm] - [Change PC settings] - [General].
B Click [Restart now] under “Advanced startup”.
C Click [Troubleshoot] - [Advanced options] - [UEFI Firmware Settings] - [Restart].
2
Write down all of the contents of the Setup Utility and press F9.
3
Press F10.
At the confirmation message, select [Yes] and press Enter.
At the confirmation message, select [Yes] and press Enter.
The computer will restart.
4
Useful Information
1
Perform “Remove everything and reinstall Windows”.
A Click [Charm] - [Change PC settings] - [General].
B Click [Get Started] under “Remove everything and reinstall Windows”.
Installation starts according to the instructions on the screen. (It will take approximately 20 minutes.)
z Do not interrupt installation, for example by turning off the computer or pressing Ctrl + Alt + Del.
Otherwise installation may become unavailable as Windows may not start up or the data may be corrupted.
5
6
When termination screen is displayed, click [OK] to turn off the computer.
Turn on the computer.
z If the password is requested, enter the Supervisor Password.
7
Perform the “First-time Operation” (Î page 15).
NOTE
z The date and time, and the time zone may not be correct. Be sure to set them correctly.
8
9
10
Start the Setup Utility and change the settings as necessary.
Perform Windows Update.
<Only for model with TPM> Clear TPM.
A Right-click any empty location on the Start screen, and click [All apps] on the toolbar.
B Click [Run] under “Windows System”, input [tpm.msc] and click [OK].
C Click “TPM Clear ...” under “Actions” on the right of the “TPM Manager on Local Computer” screen.
25
CF-AX2mk1(CPE02709YA)_OI_M.book Page 26 Wednesday, May 22, 2013 11:06 AM
Installing Software
D Click [Restart] of the “Manage the TPM security hardware” screen.
The computer will restart.
E When “TPM configuration change was requested to ...” is displayed, press F12.
The desktop screen appears.
F When “TPM is ready” appears, click [Close].
1
Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.
The Setup Utility starts up.
z If the [Panasonic] boot screen is not displayed, turn on the computer while holding down F2 or Del.
z If the password is requested, enter the Supervisor Password.
2
Write down all of the contents of the Setup Utility and press F9.
3
Press F10.
At the confirmation message, select [Yes] and press Enter.
At the confirmation message, select [Yes] and press Enter.
The computer will restart.
4
Press F2 or Del while [Panasonic] boot screen is displayed.
Useful Information
The Setup Utility starts up.
z If the password is requested, enter the Supervisor Password.
5
6
Select the [Exit] menu, then select [Recovery Partition] and press Enter.
Click [Reinstall Windows] and click [Next].
7
Click [YES].
8
9
Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].
Select the setting and click [Next].
The License Agreement screen appears.
The License Agreement screen appears.
z [Reinstall Windows to the whole Hard Disk to factory default.]
Select this option when you want to install Windows to the factory default. After installation, you can create a
new partition. For how to create a new partition, refer to “To change the partition structure” (Î page 17).
z [Reinstall to the System and OS partitions.]*1
Select this option when the hard disk has already been divided into several partitions. For how to create a new
partition, refer to “To change the partition structure” (Î page 17).
You can keep the partition structure.
*1
10
11
12
This does not appear if Windows cannot be installed to the recovery partition and the area usable by Windows.
At the confirmation message, click [YES].
<For MUI OS model>
Select language and OS (32bit or 64bit), then click [OK].
<For localized OS model>
Select OS (32bit or 64bit) and click [OK].
At the confirmation message, click [YES].
Installation starts according to the instructions on the screen. (It will take approximately 20 minutes.)
z Do not interrupt installation, for example by turning off the computer or pressing Ctrl + Alt + Del.
Otherwise installation may become unavailable as Windows may not start up or the data may be corrupted.
13
14
When Ending process screen is displayed, click [OK] to turn off the computer.
Turn on the computer.
z If the password is requested, enter the Supervisor Password.
15
16
17
Perform the “First-time Operation” (Î page 15).
Start the Setup Utility and change the settings as necessary.
Perform Windows Update.
„ Using Recovery Disc
Use the Recovery Disc in the following conditions.
• You have forgotten the administrator password.
• Installation is not complete. The recovery partition in the hard disk may be broken.
•
To change OS from Windows 7 to Windows 8, or vice versa.
26
CF-AX2mk1(CPE02709YA)_OI_M.book Page 27 Wednesday, May 22, 2013 11:06 AM
NOTE
To change OS from 32 bit to 64 bit, or vice versa, install OS using the recovery partition in the hard
z
disk.
Preparation
z Change to the laptop mode.
z Prepare the following items:
• Recovery Disc (Î
Reference Manual “Recovery Disc Creation Utility”)
• USB DVD drive (optional) (refer to recent catalogs and other sources for information about the products
available)
z Remove all peripherals (except for the USB DVD drive).
z Connect the AC adaptor and do not remove it until installation is complete.
1
Connect the DVD drive to the USB port.
2
Start the Setup Utility.
A Click [Charm] - [Change PC settings] - [General].
B Click [Restart now] under “Advanced startup”.
C Click [Troubleshoot] - [Advanced options] - [UEFI Firmware Settings] - [Restart].
Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.
z If the [Panasonic] boot screen is not displayed, turn on the computer while holding down F2
z If the password is requested, enter the Supervisor Password.
3
or Del.
Write down all of the contents of the Setup Utility and press F9.
At the confirmation message, select [Yes] and press Enter.
Check the [UEFI Boot] setting of the Setup Utility.
[UEFI Boot] should be set to as follows.
When the recovery disc for Windows 8 is used: [Enabled]
When the recovery disc for Windows 7 is used: [Disabled]
5
Set the Recovery Disc into the CD/DVD drive.
6
Press F10.
At the confirmation message, select [Yes] and press Enter.
The computer will restart.
7
Press F2 or Del while [Panasonic] boot screen is displayed.
Useful Information
4
The Setup Utility starts up.
z If the password is requested, enter the Supervisor Password.
8
9
Select the [Exit] menu, then select your DVD drive in [Boot Override].
Press Enter
The computer will restart.
10
11
12
13
Click [Reinstall Windows] and click [Next].
At the confirmation message, click [YES].
At the License Agreement screen, click [Yes, I agree to the provisions above and wish
to continue!] and click [Next].
When the recovery disc for Windows 8 is used, click [Next].
When the recovery disc for Windows 7 is used, select the setting and click [Next].
z [Reinstall Windows to the whole Hard Disk to factory default.]
Select this option when you want to install Windows to the factory default. After installation, you can create a
new partition. For how to create a new partition, refer to “To change the partition structure” (Î page 17)
z [Reinstall to the System and OS partitions.]*2
Select this option when the hard disk has already been divided into several partitions. For how to create a new
partition, refer to “To change the partition structure” (Î page 17).
You can keep the partition structure.
*2
This does not appear if Windows cannot be installed to the recovery partition and the area usable by Windows.
27
CF-AX2mk1(CPE02709YA)_OI_M.book Page 28 Wednesday, May 22, 2013 11:06 AM
Installing Software
14
At the confirmation message, click [YES].
Installation starts according to the instructions on the screen. (It will take approximately 30 - 45 minutes.)
z Do not interrupt installation, for example by turning off the computer or pressing Ctrl + Alt + Del.
Otherwise installation may become unavailable as Windows may not start up or the data may be corrupted.
15
When Ending process screen is displayed, remove the Recovery Disc and DVD drive.
Click [OK] to turn off the computer.
Click [OK].
The computer will restart.
16
Turn on the computer.
z If the password is requested, enter the Supervisor Password.
17
Perform the “First-time Operation” (Î page 15).
NOTE
z
18
19
Useful Information
20
28
The date and time, and the time zone may not be correct. Be sure to set them correctly.
Start the Setup Utility and change the settings as necessary.
Perform Windows Update.
<Only for model with TPM> Clear TPM (Î page 25).
CF-AX2mk1(CPE02709YA)_OI_M.book Page 29 Wednesday, May 22, 2013 11:06 AM
Troubleshooting (Basic)
Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the
“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact
Panasonic Technical Support. You can also check the computer’s status in the PC Information Viewer (Î
ence Manual “Checking the Computer’s Usage Status”).
Refer-
„ Starting Up
The computer does not
power on / The power status
indicator or battery indicator
is not lit.
z
z
z
z
Windows does not start up.
z Remove all peripheral devices (e.g. USB memory).
z If the power status indicator is lit, slide the power switch for four seconds or longer to
turn off, then turn on again.
z
Using the following procedure, start up in Safe Mode, and check the
error details.
A Turn on the computer, and when the [Panasonic] boot screen disappears (after
entering the password*1 if one is set) hold down F8.
B Release your finger when [Windows Advanced Options Menu] is displayed, and
with Ï or Ð, select [Safe Mode], then press Enter.
Follow the on-screen instructions.
*1
Supervisor Password or User Password set with the Setup Utility
z Press F9 in the Setup Utility to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again.
z Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot] should be set to
[Enabled] /
[Disabled].
You have forgotten the
password.
z Supervisor Password or User Password: Contact Panasonic Technical Support.
z Administrator password:
• If you have another account with Administrator authority, log-on with it, then delete
the password for the problem account.
• If you have a password reset disk, click [Reset password] displayed after the
password input error, then follow the on-screen instructions and set a new password.
If you cannot do either of the above, you will need to reinstall (Î page 25) and
setup Windows.
“Remove disks or other
media. Press any key to
restart” or a similar message appears.
z A floppy disk in the drive or USB memory is connected, and it does not contain system
startup information. Remove the floppy disk and USB memory, then press any key.
z If a device is connected to the USB port, disconnect the device, or set [USB Port] or
[Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.
z If the problem persists after removing the disk, it may be a flash memory drive failure. Perform the installation and return the flash memory drive to its condition at the
time of purchase. (Î page 25) If the problem persists even after the reinstallation,
contact Panasonic Technical Support.
Troubleshooting
Connect the AC adaptor.
Insert a fully charged battery.
Remove the battery pack and the AC adaptor, then connect them again.
When the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If
the computer does not power on even after cooling down, contact your technical support
office.
z Pull out the AC cord and wait for more than 1 minute to reconnect the AC cord.
29
CF-AX2mk1(CPE02709YA)_OI_M.book Page 30 Wednesday, May 22, 2013 11:06 AM
Troubleshooting (Basic)
„ Starting Up
The date and time are incor- z Make the correct settings.
rect.
A Open the Control Panel.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Control Panel] under “Windows System”.
Click
(Start) - [Control Panel].
B Click [Clock, Language, and Region] - [Date and Time].
C Click [Change time zone…].
D Select the time zone, then click [OK].
E Click [Change date and time…], then set the date and time.
z If the problem persists, the internal clock battery may need to be replaced. Contact
Panasonic Technical Support.
z When the computer is connected to LAN, check the date and time of the server.
z The 2100 A.D. or later year will not be correctly recognized on this computer.
[Executing Battery Recalibration] screen appears.
z The Battery Recalibration was canceled before Windows was shut down last time.
To start up Windows, turn off the computer by the power switch, and then turn on.
[Enter Password] does not
appear when resuming from
sleep / hibernation.
z Select [Enabled] in [Password On Resume] in the [Security] menu of the Setup Utility
(Î
Reference Manual “Setup Utility”).
z The Windows password can be used instead of the password set in the Setup Utility.
A Open the Control Panel.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Control Panel] under “Windows System”.
Click
(Start) - [Control Panel].
B Click [User Accounts and Family Safety] - [Add or remove user accounts].
C Click [System and Security] - [Power Option] - [Require a password when the
computer wakes] and add a check mark for [Require a password].
Troubleshooting
The computer will not automatically enter sleep or
hibernation.
z If you connect to a network using wireless LAN function, perform access point settings.
Reference Manual “Wireless LAN”)
(Î
z If you do not use wireless LAN function, turn off wireless LAN function.
(Î
Reference Manual “Disabling/Enabling Wireless Communication”)
z Make sure that you are not using any software that regularly accesses the hard disk.
When logging on (e.g.,
resuming the computer),
audio is distorted.
z Perform the following steps to change the audio settings to prevent audio output.
A Click the [Desktop] tile on the Start screen.
B Right-click the desktop and click [Personalize] - [Sound].
C Remove the check mark from [Play Windows Startup sound], and click [OK].
A Right-click the desktop and click [Personalize] - [Sounds].
B Remove the check mark from [Play Windows Startup sound], and click [OK].
Cannot resume.
z One of the following operations may have been carried out. Slide the power switch to
turn on the computer. Data not saved will be lost.
• In sleep mode, the AC adaptor or battery pack was disconnected, or a peripheral
was connected or disconnected.
• The power switch was slid for four seconds or longer to forcibly turn off the computer.
30
CF-AX2mk1(CPE02709YA)_OI_M.book Page 31 Wednesday, May 22, 2013 11:06 AM
„ Starting Up
Other startup problems.
z Check to see if there was a disk error.
A Remove all peripheral devices including an external display.
B Open “Computer”.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Computer] under “Windows System”.
C
D
E
F
Click
(Start) - [Computer].
Right-click [Local Disk (C:)], and click [Properties].
Click [Tools] - [Check Now...].
• A standard user needs to enter an administrator password.
Select the option in [Check disk options] and click [Start].
Click [Schedule disk check] and restart the computer.
z
Start the computer in Safe Mode and check the error details. (Î page 29 “Windows
does not start up”.)
„ Entering Password
Even after entering the
password, password input
screen is displayed again.
z The computer may be in ten-key mode.
If the NumLk indicator
lights, press NumLk to disable the ten-key mode, and then input.
z The computer may be in Caps Lock mode.
If the Caps Lock indicator
lights, press Caps Lock to disable the Caps Lock
mode, and then input.
Cannot log on to Windows.
(“The user name or password is incorrect” is displayed.)
z The user name (account name) includes an “@” mark.
If another user account exists:
Log on to Windows using another user account, and delete the account that
includes “@”. Then create a new account.
If no other account exists:
You need to reinstall Windows (Î page 25).
„ Shutting down
z Remove all peripheral devices.
z Wait one or two minutes. It is not a malfunction.
„ Display
When the screen becomes
black for a moment.
z When you set [Display power saving function] of Power Plan Extension Utility to
[Enabled], if you do the following operations, the screen becomes black for a
moment, but this is not a malfunction. You can use it.
• Adjust the brightness of the screen with Fn + F1 / Fn + F2.
• Remove and insert the AC adaptor.
While you are using motion video playback software, benchmark software for
graphic, if error screen is displayed or application software does not function normally, set [Display power saving function] to [Disabled].
No display.
z The external display is selected. Press Fn + F3 (or
+ P) to switch the display.
Wait until the display has been switched completely before pressing Fn + F3 (or
Troubleshooting
Windows does not shut
down.
+ P) again.
z The display is turned off by the power-saving function. To resume, do not press the
direct selection keys, but press any other key like Ctrl.
z The computer entered sleep or hibernation by the power-saving function. To
resume, slide the power switch.
z The screen may become darker. Press Fn + F2 to make the screen brighter.
31
CF-AX2mk1(CPE02709YA)_OI_M.book Page 32 Wednesday, May 22, 2013 11:06 AM
Troubleshooting (Basic)
„ Display
The screen is disordered.
z Changing the number of display colors and resolution may affect the screen. Restart
the computer.
z The refresh rate of the internal LCD may be 40 Hz. Change the refresh rate of the
internal LCD.
A
1. Click the [Desktop] tile on the Start screen.
2. Right-click on the desktop, and click [Graphics Properties].
Right-click on the desktop, and click [Graphics Properties].
B Click [OK].
C If [Refresh Rate] for the Notebook is [40 Hz], change to [60 Hz] and click [OK].
The external display does
not work normally.
z If the external display does not support the power saving function, it may not work normally when the computer enters the power saving mode. Turn off the external display.
The image on the display
does not rotate.
z The application program currently running may not support the image rotation. Quit
the program, and then try to rotate the image. This can ameliorate the status.
z Under the factory default settings, the image display will not rotate automatically in
Laptop mode. The image will not rotate in Tablet mode either if the auto rotation is disabled.
Troubleshooting
„ Battery
The battery indicator
lights red.
z The battery level is very low (the charge is approx. 9% or less).
z Connect the AC adaptor. You can use the computer when the indicator light is orange. If
you do not have an AC adaptor, save your data and power off your computer. After
replacing the battery pack with a fully charged one, turn your computer on again.
The battery indicator
lights red.
z Quickly saver your data and power off your computer.
z Connect the AC adaptor and wait until the battery indicator
The battery indicator is
blinking.
z If blinking red:
Quickly save your data and power off your computer. Remove the battery pack and disconnect the AC adaptor, then connect them again. If the problem persists, contact Panasonic Technical Support. The battery pack or charging circuit may be defective.
z If blinking orange:
• Battery cannot be recharged temporarily because the internal temperature of the
battery pack is outside the acceptable temperature range for recharging. Your
computer can be used normally in this state. Once the range requirement is satisfied, charging begins automatically.
• Software applications and peripheral devices (USB devices, etc.) are consuming
too much power. Exit the software applications currently running, and remove all
peripherals. Once the range requirement is satisfied, charging begins automatically.
The battery indicator is
flashing.
z The battery is recharging.
If [Battery Charging Indicator] in [Main] menu of the Setup Utility is set to [Flashing], the
indicator will alternately become lighter and darker.
„ Touch Pad
The cursor does not work.
32
lights orange.
z When using the external mouse, connect it correctly.
z Restart the computer using the keyboard.
z If the computer does not respond to keyboard commands, read “No response”
(Î page 33).
z You cannot use the Touch Pad in the Tablet mode.
z If the Touch Pad cannot be used in the Laptop mode, the computer may be in the
HOLD mode. Press the HOLD button to deactivate the HOLD mode.
CF-AX2mk1(CPE02709YA)_OI_M.book Page 33 Wednesday, May 22, 2013 11:06 AM
„ On-screen Document
The document of PDF format is not displayed.
z Install Adobe Reader.
A Log on to Windows as an administrator.
B Click
(Start) and input “c:\util\reader\Pinstall.bat” in [Search Programs and
files] then press Enter.
C Update Adobe Reader to its latest version.
If your computer is connected to the internet, start up Adobe Reader and click
[Help] - [Check for Updates...].
„ Others
No response.
z Press Ctrl+Shift+Esc to open Task Manager and close the software application
that is not responding.
z An input screen (e.g., password input screen at startup) may be hidden behind
another window. Press Alt+Tab to check.
z Press the power switch for four seconds or longer to shut down the computer, and
then press the power switch to turn it on. If the application program does not work
normally, uninstall and reinstall the program. To uninstall,
A Open the Control Panel.
1. Right-click any empty location on the Start screen.
2. Click [All apps] on the toolbar.
3. Click [Control Panel] under “Windows System”.
The battery status indicator
lights green and then turns
off immediately.
z When the battery is fully charged and the computer is not operating (i.e., it is turned
off or in sleep mode), the power supply from the AC adaptor stops and power consumption is inhibited.
In such cases, the indicator will light green upon connecting the AC adaptor, but
only for a moment.
The recovery disc for Windows 8 in not functioning.
z Perform recovery using the recovery disc for Windows 7 first, and then perform
recovery using the recovery disc for Windows 8.
Troubleshooting
Click
(Start) - [Control Panel].
B Click [Program] - [Uninstall a program].
33
CF-AX2mk1(CPE02709YA)_OI_M.book Page 34 Wednesday, May 22, 2013 11:06 AM
LIMITED USE LICENSE AGREEMENT
THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”)
ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH
THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY
DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.
Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses their use to you. You
assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended
results, and for the installation, use and results obtained therefrom.
LICENSE
A. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive right and license to use
the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are
receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no
title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which
title, ownership and rights shall remain with Panasonic Corporation or its suppliers.
B. You may use the Programs only on the single Product which was accompanied by the Programs.
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distribute or otherwise make the Programs or related documentation available to any third party, by time-sharing or otherwise, without the prior written consent of Panasonic Corporation.
D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for
any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your
use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or
attempt to modify, the Programs.
E. You may transfer the Programs and license them to another party only in connection with your transfer of the single
Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also
transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation,
to the same party or destroy any such copies not so transferred.
F. You may not remove any copyright, trademark or other notice or product identification from the Programs and you
must reproduce and include any such notice or product identification on any copy of any Program.
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE
THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN
WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.
Appendix
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PERMITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.
34
TERM
This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate
this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof
set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any
such termination, you agree to destroy, at your expense, the Programs and related documentation together with all copies thereof in any form.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND
BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,
ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MATTER OF THIS AGREEMENT.
CF-AX2mk1(CPE02709YA)_OI_M.book Page 35 Wednesday, May 22, 2013 11:06 AM
Specifications
This page provides the specifications for the basic model. The model number is different according to the unit configuration.
z To check the model number:
Check the bottom of the computer or the box the computer came in at the time of purchase.
z To check CPU speed, memory size and the flash memory drive (SSD) size:
Run the Setup Utility (Î
Reference Manual “Setup Utility”) and select [Information] menu.
[Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Hard disk drive size
„ Main Specifications
Model No.
CF-AX2LDC series
CPU/Secondary cache memory
Intel® Core™ vPro™ i5-3427U Processor (3 MB*1 cache, up to 2.80 GHz) with Intel® Turbo
Boost Technology
Chip Set
Mobile Intel® QM77 Express Chipset
Video controller
Built-in Chip Set
Main Memory*2
4 GB*1, DDR3L SDRAM
Video Memory*1*3
CF-AX2LDW series
UMA 1664 MB Max.
UMA <32-bit> 1544 MB Max. <64-bit> 1696 MB Max.
Flash Memory Drive (SSD)*4
128 GB
Approx. <For localized OS model> 10 GB / <For MUI OS model> 12 GB (SSD Recovery partition) and approx. 1 GB (Recovery partition) are used as recovery partitions. (Users cannot use
these partitions.)
<Only for Windows 7 downgrade model>
Approx. <For localized OS model> 30 GB / <For MUI OS model> 50 GB is used as a partition
with HDD recovery tools. (Users cannot use this partition.)
Approx. 300 MB is used as a partition with system tools. (Users cannot use this partition.)
11.6 type (TFT) (1366 x 768 dots)
Internal LCD
65,536/16,777,216 colors (1366 x 768 dots)*5
External Display*6
65,536/16,777,216 colors (1024 × 768 dots/1280 × 768 dots/1280 × 1024 dots/1360 × 768 dots/
1366 × 768 dots/1400 × 1050 dots/1600 × 900 dots/1600 × 1200 dots/1680 × 1050 dots/
1920 × 1080 dots/1920 × 1200 dots)
Simultaneous Display on LCD
+ External Display*6
65,536/16,777,216 colors (1024 × 768 dots/1280 × 768 dots/1360 × 768 dots/ 1366 x 768 dots)
Wireless LAN
Intel® Centrino® Advanced-N 6205 (Î page 37)
Bluetooth
Î page 37
Wireless
WAN*7
Equipped for some models (Î page 37)
LAN
IEEE 802.3 10Base-T / IEEE 802.3u 100BASE-TX / IEEE 802.3ab 1000BASE-T
Sound
WAVE and MIDI playback, Intel® High Definition Audio subsystem support
Security Chip
TPM (TCG V1.2 compliant)*8
Card
Slots
SD Memory Card
Slot*9
x1
SIM Card Slot*7
x1
Smart Card Slot
–
x 1*10
Interface
USB 3.0 Ports x 2 (right side)*11 / LAN Port (RJ-45) x 1 / External Display Port (VGA) (Mini Dsub
15-pin female) / HDMI Port (Type A)*12 / Microphone Jack (Miniature jack, 3.5 DIA) / Headphone Jack (Miniature jack, 3.5 DIA)
Keyboard / Pointing Device
84 or 85 keys / Touch Pad
Appendix
Display Method
35
CF-AX2mk1(CPE02709YA)_OI_M.book Page 36 Wednesday, May 22, 2013 11:06 AM
Specifications
„ Main Specifications
Model No.
CF-AX2LDC series
Camera
Resolution
High Definition 720P
Effective
number of
pixels
Max. 1280 x 720
Microphone
Built-in (monaural)
CF-AX2LDW series
Ambient light Equipped
sensor
Sensor
Magnetic
sensor
Gyro sensor
Acceleration
sensor
Power Supply
AC adaptor or Battery pack
AC Adaptor
Input: 100 V - 240 V AC, 50 Hz/60 Hz, Output: 16 V DC, 5.0 A
Battery Pack
Li-ion 7.2 V, Typical 4400 mAh / Minimum 4100 mAh
Built-in Battery
(not replaceable)
Li-ion 7.2 V, Typical 2200 mAh /
Minimum 2050 mAh
Li-ion 7.2 V, Typical 1090 mAh /
Minimum 1030 mAh
Operating Time*14
Approx. 8 hours (Economy Mode (ECO) - Disable)
Approx. 6.5 hours (Economy Mode (ECO) Disable)
Charging Time*15
Approx. 4 hours
• When the built-in battery is fully charged
Approx. 2 hours
Approx. 3.5 hours
• When the built-in battery is fully charged
Approx. 2 hours
Power Consumption*16
Approx. 20 W*17/ Approx. 45 W (maximum when recharging in the ON state)
Physical Dimensions
(W × D × H)
288 mm × 194 mm × 18 mm
Weight *18
Approx. 1.15 kg (for models without wireless
WAN)
Approx. 1.155 kg (for models with wireless
WAN)
*13
EnviOperronment ating
Storage
Temperature
5 °C to 35 °C
Humidity
30% to 80% RH (No condensation)
Temperature
-20 °C to 60 °C
Humidity
30% to 90% RH (No condensation)
Approx. 1.125 kg (for models without wireless
WAN)
Approx. 1.13 kg (for models with wireless
WAN)
„ Software
Base OS
Windows® 8 Pro 64-bit
Installed OS*19
Windows® 8 Pro 64-bit
<Only for Windows 7 downgrade model>
Appendix
Windows® 7 Professional 32-bit Service Pack 1 (downgraded to Windows® 7) / Windows® 7
Professional 64-bit Service Pack 1 (downgraded to Windows® 7)
Pre-installed Software*19
Adobe Reader, PC Information Viewer, Intel® PROSet/Wireless Software,
Bluetooth Stack for Windows® by TOSHIBA, Hotkey Settings, Battery Recalibration Utility,
Infineon TPM Professional Package*8 *20, Aptio Setup Utility, PC-Diagnostic Utility,
Hard Disk Data Erase Utility*21, Recovery Disc Creation Utility, Dashboard for Panasonic PC,
Power Plan Extension Utility, Camera Utility, USB Charge Setting Utility, PC Information Popup,
HOLD Mode Settings Utility, Manual Selector
Camera for Panasonic PC, Wireless Toolbox
Quick Boot Manager, Wireless Switch Utility, Wireless Connection Disable Utility*22
36
CF-AX2mk1(CPE02709YA)_OI_M.book Page 37 Wednesday, May 22, 2013 11:06 AM
„ Wireless LAN
Data Transfer Rates
IEEE802.11a
IEEE802.11b
IEEE802.11g
IEEE802.11n*24
Standards Supported
IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11n
Transmission Method
OFDM system, DS-SS system
Wireless Channels Used
IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/120/124/128/132/136/
140
IEEE802.11b/IEEE802.11g : Channels 1 to 13
IEEE802.11n : Channels 1-13/36/40/44/48/52/56/60/64/100/104/108/112/116/120/124/128/132/
136/140
RF Frequency Band
IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz
IEEE802.11b/IEEE802.11g : 2.412 GHz - 2.462 GHz
IEEE802.11n : 2.412 GHz - 2.462 GHz, 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz
: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*23
: 11/5.5/2/1 Mbps (automatically switched)*23
: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*23
: (HT20) GI*25 = 400ns: 150/130/115/86/72/65/57/43/28/21/14/7 Mbps (automatically switched)*23
*25
GI = 800ns: 130/117/104/78/65/58/52/39/26/19/13/6 Mbps (automatically switched)*23
*25
(HT40)GI = 400ns: 300/270/240/180/150/135/120/90/60/45/30/15 Mbps
(automatically switched)*23
*25
GI = 800ns: 270/243/216/162/135/121/108/81/54/40/27/13 Mbps
(automatically switched)*23
„ Bluetooth
Bluetooth Version
4.0
Classic mode / Low Energy mode
Transmission Method
FHSS system
Wireless Channels Used
Channel 1 to 79 / Channel 0 to 39
RF Frequency Band
2.402 GHz - 2.480 GHz
„ Wireless WAN*7
Other Features
SIM
Category 6, 5.7 Mbps
HSUPA
(HSPA+)
Category 10, 14.4 Mbps
UMTS
3GPP Release 6
EDGE/
GPRS
MultiSlot Class 10
Circuit Switched Data
SMS
Mobile Originated SMS (MO-SMS)
Mobile Terminated SMS (MT-SMS)
FAX
No Support
Voice
No Support
1.8/3V SIM Support
Appendix
Data Communication HSUPA
37
CF-AX2mk1(CPE02709YA)_OI_M.book Page 38 Wednesday, May 22, 2013 11:06 AM
Specifications
*1
*2
*3
*4
*5
*6
*7
*8
*9
*10
*11
*12
*13
*14
*15
Appendix
*16
*17
*18
*19
*20
38
1 MB = 1,048,576 bytes /
1 GB = 1,073,741,824 bytes
For 32-bit OS, the usable memory available will be less
depending on the specifications (3.4 GB to 3.5 GB).
A segment of the main memory is allotted automatically
depending on the computer’s operating status. The size of
the Video Memory cannot be set by the user. The size of
Video memory is allotted depending on the operating system.
1 MB = 1,000,000 bytes / 1 GB = 1,000,000,000 bytes. Your
operating system or some application software will report as
fewer GB.
A 16,777,216 color display is achieved by using the dithering
function.
Display may be impossible using some connected external
displays.
Only for model with wireless WAN. The specification may differ depending on models.
Only for model with TPM.
For information on TPM,
on the Start screen,
click the [Manual Selector] tile, and select “Installation Manual for Trusted Platform Module (TPM)” /
Double-click [Manual Selector] on the desktop, and select
“Installation Manual for Trusted Platform Module (TPM)”.
This slot is compatible with High-Speed Mode. Operation has
been tested and confirmed using Panasonic SD/SDHC/
SDXC Memory Cards with a capacity of up to 64 GB. Operation on other SD equipment is not guaranteed.
Only for model with Smart Card Slot.
Compatible with USB 1.1/2.0/3.0. Does not guarantee operation of all USB-compatible peripherals.
Does not guarantee operation of all HDMI-compatible peripherals.
<Only for North America>
The AC adaptor is compatible with power sources up to
240 V AC adaptor.
The unit for North America (identified by the suffix ‘M’ on the
model number) is supplied with a 125 V AC compatible AC
cord.
20-M-2-1
Measured with LCD brightness : 60 cd/m2 Varies depending
on the usage conditions, or when an optional device is
attached.
Varies depending on the usage conditions, CPU speed, etc.
Approx. 0.5 W when the battery pack is fully charged (or not
being charged) and the computer is off.
<When using with 115 V AC>
Even when the AC adaptor is not connected to the computer,
power is consumed (Max. 0.2 W) simply by having the AC
adaptor plugged into an AC outlet.
<When using with 240 V AC>
Even when the AC adaptor is not connected to the computer,
power is consumed (Max. 0.4 W) simply by having the AC
adaptor plugged into an AC outlet.
Rated power consumption.
23-E-1
Average value. May differ depending on models.
Operations of this computer are not guaranteed except for
the pre-installed OS and the OS which is installed by using
the hard disk recovery and the recovery disc.
Must be installed before use.
*21
Perform on the recovery partition. (If this software can not be
performed on the recovery partition, perform from the recovery disc)
Perform from the recovery disc.
Must be installed before use.
*23 These are speeds specified in IEEE802.11a+b+g+n standards. Actual speeds may differ.
*24
Available when set to “WPA-PSK”, “WPA2-PSK” or “none”.
*25 Only available when HT40 enabled by the computer.
*22
CF-AX2mk1(CPE02709YA)_OI_M.book Page 39 Wednesday, May 22, 2013 11:06 AM
Standard Limited Warranty
Panasonic System Communications Company Europe
Panasonic System Communications Company Europe (referred to as “Panasonic”) will repair this product (other than
software, which is treated in a different section of this warranty) with new or refurbished parts, from the date of original
purchase in the event of a defect in materials or workmanship. This warranty only applies to new Panasonic Toughbooks purchased in the EEA and Switzerland and Turkey.
Panasonic (or its authorised Service Provider) target to repair your equipment within 48 hours from its receipt in our service centre.
Additional charges may apply for shipment to countries outside of the European Union. Panasonic will use all reasonable endeavours to ensure this service.
This warranty only covers failures due to defects in materials or workmanship which occur during normal use for the
applicable Service Agreement Period listed below. In the event that any product (or part thereof) is replaced, Panasonic
shall transfer ownership of the replacement product (or part) to the customer and the customer shall transfer ownership
of the replaced product (or part) to Panasonic.
Service Agreement Period - from original date of purchase
• Toughbooks (and every accessory included in the original packaging except the battery) - 3 years
• Toughpads (and every accessory included in the original packaging except the battery) - 3 years
• Accessories included in the original package - 3 years
• Additional peripherals manufactured by Panasonic (including media bay devices such as CD-Rom drives) - 1 year
• Batteries - 6 months. Panasonic Warranty covers the battery for six months. A battery is considered good if it
maintains 50% of its charge capacity during the warranty period. If a battery is returned under this contract and
testing determines that it has charge capacity greater than 50%, the battery will be returned with an invoice for the
retail purchase price of a new battery.
This warranty is extended solely to the original purchaser. A purchase receipt or other proof of date of original purchase
will be required before warranty performance is rendered.
Limits and Exclusions:
This warranty does not cover and shall be void for:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Broken or cracked LCD screen.
Defective pixel in notebook displays and LCD screens within 0.002%
Damage that is attributable to fire, theft or acts of God.
Damage caused by environmental influences (electrical storms, magnetic fields etc.).
Damage which has not been caused during normal operation
Repair of damage that is cosmetic only or does not affect product functionality such as wear and tear, scratches and dents.
Failures caused by products not supplied by Panasonic.
Failures resulting from alteration, accidental damage, casualty, misuse, abuse or neglect.
Introduction of liquid or other foreign matter into the unit.
Improper installation, operation or maintenance.
Improper connections with peripherals.
Maladjustment of consumer controls such as function settings.
Modification or service by anyone other than Panasonic or its approved Service Providers.
Products used as short term rental or leased equipment.
Products whose serial number has been removed making the unit warranty condition impossible to clearly determine.
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR
TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS. PANASONIC
WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING
OUT OF THE FOREGOING USES.
We strongly recommend that customers backup their data before sending back their unit to an Authorised Service Provider.
Panasonic shall not be liable for loss of data or other incidental or consequential damages resulting from the use of this
product, or arising out of any breach of this warranty. All express and implied warranties, including the warranties of satisfactory quality and fitness for a particular purpose are limited to the applicable warranty period set forth above. Panasonic shall not be liable for any indirect, special or consequential loss or damage (including without limitation any loss of
profits) arising from the use of this product or for any breach of this warranty.
This limited warranty gives you specific legal rights, and you may have other rights that vary from country to country.
You must consult the applicable country laws for a full determination of your rights. This limited warranty is in addition
to, and does not affect any rights arising out of any contract of sale or by statute.
Appendix
There are no other express warranties except as listed above.
39
CF-AX2mk1(CPE02709YA)_OI_M.book Page 40 Wednesday, May 22, 2013 11:06 AM
Standard Limited Warranty
Panasonic System Communications Company Europe
Data Storage Media
Data Storage Media is the media on which the Operating System, drivers and programs originally installed by Panasonic on the main unit are stored. This media is originally provided with the unit.
Panasonic warrants to you only that the disc(s) or other media on which the Programs are furnished will be free from
defects in material and workmanship under normal use for a period of sixty (60) days from the date of delivery thereof to
you, as evidenced by your purchase receipt.
This is the only warranty Panasonic makes to you. Panasonic does not warrant that the functions contained in the Programs will meet your requirements or that the operation of the Programs will be uninterrupted or error free.
Panasonic’s entire liability and your exclusive remedy under this warranty shall be limited to the replacement of any
defective disk or other media which is returned to Panasonic's authorized Service Centre, together with a copy of the
purchase receipt, within the aforesaid warranty period.
Panasonic shall have no obligation for any defects in the disk(s) or other media on which the Programs are furnished
resulting from your storage thereof, or for defects that have been caused by operation of the disk(s) or other media otherwise than on the Product or in the environment conditions other than those specified by Panasonic by alteration, accident, misuse, abuse, neglect, mishandling, misapplication, installation, maladjustment of consumer controls, improper
maintenance, modification or damage that is attributable to acts of God. In addition, Panasonic shall have no obligation
for any defects in the disk(s) or other media if you have modified, or attempted to modify any Program.
Duration of implied warranties, if any is limited to sixty (60) days.
Pre-installed software
Pre-installed software means the software shipped pre-loaded by Panasonic, not that loaded by any third party or selling agent.
Panasonic and its suppliers makes no warranty, either express, implied or statutory, with respect to software provided with the
Product and licensed to Purchaser, its quality, performance, merchantability, or fitness for a particular purpose. Panasonic
does not warrant that the functions contained in the software will be uninterrupted or error free. Panasonic assumes no risk of
and shall not in any case be liable for any damages, including, without limitation, any special, incidental, consequential, or
punitive damages arising from breach of warranty or contract, negligence or any other legal theory, including, without limitation
loss of goodwill, profits or revenue, loss of use of the Programs or Products or any associated equipment, cost of capital, cost
of any substitute equipment, facilities, or services, downtime costs, or claims of any party dealing with such damages.
Some countries do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights and you may also have other rights that vary from country to country. You must consult applicable country laws for a full determination of your rights.
Appendix
Contacts
40
Address
Panasonic System Communications Company Europe
Panasonic Manufacturing U.K. Ltd.
Service Centre Building B4,
Wyncliffe Road, Pentwyn Industrial Estate, Cardiff,
United Kingdom
CF23 7XB
Web page
http://www.toughbook.eu/
Helpdesk
English speaking service
French speaking service
German speaking service
Italian speaking service
Spanish speaking service
E-mail address
+44 (0) 8709 079 079
+33 (0) 1 47 91 64 99
+49 (0) 1805 410 930
+39 (0) 848 391 999
+34 (0) 901 101 157
toughbooksupport@eu.panasonic.com
Czech speaking service
Hungarian speaking service
Polish speaking service
Romanian speaking service
Slovakian speaking service
E-mail address
+420 (0) 800 143234
+36 (0) 6800 163 67
+48 (0) 800 4911558
+40 (0) 800 894 743
+421 (0) 800 42672627
toughbooksupport@csg.de
Payments
toughbookservicepayments.cardiff@eu.panasonic.com
CF-AX2mk1(CPE02709YA)_OI_M.book Page 41 Wednesday, May 22, 2013 11:06 AM
MEMO
41
CF-AX2mk1(CPE02709YA)_OI_M.book Page 42 Wednesday, May 22, 2013 11:06 AM
MEMO
42
CF-AX2mk1(CPE02709YA)_OI_M.book Page 43 Wednesday, May 22, 2013 11:06 AM
43
CF-AX2mk1(CPE02709YA)_OI_M.book Page 44 Wednesday, May 22, 2013 11:06 AM
As an ENERGY STAR® Partner, Panasonic Corporation has determined that this product meets
ENERGY STAR® guidelines for energy efficiency. By enabling available power management
settings,
Panasonic computers enter a low-power sleep mode after a period of inactivity, saving the user
energy.
Outline of the International ENERGY STAR® Office Equipment Program
The international ENERGY STAR® Office Equipment Program is an international program that promotes energy
saving through the use of computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers,
displays, printers, facsimiles, and copiers. Their standards and logos are uniform among participating nations.
22-E-1
Importer’s name & address pursuant to the EU GPSD (General Product Safety Directive) 2001/95/EC Art.5
Panasonic System Communications Company Europe, Panasonic Marketing Europe GmbH
Hagenauer Straße 43
65203 Wiesbaden
Germany
© Panasonic Corporation 2013
Printed in UK
UK0113-1053
CPE02709YA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising