User guide for BISSELL Powerforce 300 Vacuum 14012

User guide for BISSELL Powerforce 300 Vacuum 14012
1401 SERIES
USER GUIDE
POWERFORCE 300™
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
BEFORE USING YOUR VACUUM.
When using an electrical appliance, basic precautions should be
observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY:
»This
appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Cleaning and user
maintenance shall not be made by
children without supervision.
»Children should be supervised to ensure
that they do not play with the appliance.
» If the supply cable is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
»Keep hair, loose clothing, fingers, and
all parts of body away from openings
and moving parts of the appliance and
its accessories.
»Do not leave appliance when plugged in.
»Unplug from electrical socket when not in use and
before servicing.
»Do not allow to be used as a toy.
»Use only as described in this user guide.
»Use only manufacturer’s recommended attachments.
»Do not use with damaged cable or plug.
»Do not immerse in water or liquid.
»If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water; do not attempt to operate it and return it to
a service center.
»Do not pull or carry by cable, use cable as a handle,
close door on cable, or pull cable around sharp edges
or corners.
»Do not run appliance over cable.
»Keep cable away from heated surfaces.
»Do not unplug by pulling on cable.
»To unplug, grasp the plug, not the cable.
»Do not handle plug or appliance with wet hands.
»Do not put any object into openings.
»Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
»Turn off all controls before unplugging.
»Use extra care when cleaning on stairs.
»Do not use to pick up flammable or combustible
liquids, such as petroleam, or use in areas where they
may be present.
»Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.)
»Do not use appliance in an enclosed space filled with
vapours given off by oil base paint, paint thinner, some
mothproofing substances, flammable dust, or other
explosive or toxic vapours.
»Do not pick up hard or sharp objects such as glass,
nails, screws, coins, etc.
»Use only on dry, indoor surfaces.
»Keep appliance on a level surface.
»Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
»Do not use without dust bag and/or filters in place.
»Do not use outdoors or on wet surfaces
»If your appliance is fitted with a nonrewireable BS
1363 plug it must not be used unless a 13 amp (ASTA
approved to BS 1362) fuse is fitted in the carrier contained in the plug. (Spares may be obtained from your
BISSELL supplier). If for any reason the plug is cut off,
it must be disposed of, as it is an electric shock hazard
should it be inserted into a mains socket
»Do not leave machine running in the same spot without
handle fully upright.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
FOR OPERATION ON A 220-240 VOLT A.C. 50/60 HZ POWER SUPPLY ONLY.
This model is for household use only.
2
www.BISSELL.com
Thanks for buying a BISSELL vacuum
We’re glad you purchased a BISSELL vacuum. Everything we
know about floor care went into the design and construction of
this complete, high-tech home cleaning system.
Your BISSELL vacuum is well made, and we back it with a limited
two-year guarantee. We also stand behind it with a knowledgeable,
dedicated Consumer Care department, so, should you ever have a
problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service
of high-quality homecare products like your BISSELL vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman & CEO
Symbol Definitions
WARNING
AN ACTION OR ATTENTION IS NEEDED TO
THIS AREA IN ORDER TO REDUCE THE RISK
OF ELECTRIC SHOCK, FIRE, OR INJURY
TIP
NOTE OR HINT WHICH IS NOT ESSENTIAL
BUT MAY IMPROVE USABILITY
GUIDE
READ USER GUIDE FOR COMPLETE
SAFETY AND USER INSTRUCTIONS
WEEE
DO NOT THROW THE APPLIANCE AWAY
WITH THE NORMAL HOUSHOLD WASTE
AT THE END OF ITS LIFE, BUT HAND IT IN
AT AN OFFICIAL COLLECTION POINT FOR
RECYCLING. BY DOING THIS YOU WILL
HELP TO PRESERVE THE ENVIRONMENT.
www.BISSELL.com
3
A
B1
Product View
Assembly (handle)
1
2.
4.
2
B2
Assembly (hose)
12
1.
2.
14
3.
4.
3
4
13
5
15
16
6
17
18
7
19
20
8
21
6.
9
23
10
26
5.
11
24
22
27
25
28
29
30
2.
3.
1.
3.
4.
4
www.BISSELL.com
C1
Handle Position
D1
Cleaning Inner Cyclone Filter
3.
D2
C2
4.
Cleaning
Post Motor Filter
2.
C3
Height
Adjustment
Empty Dirt Tank
2.
3.
5.
D3
6.
Checking Brush & Drive Belt
4.
3.
8.
D4
4.
Replacing
Drive Belt
D5
2.
Clearing Clogs
3.
5.
6.
www.BISSELL.com
5
A Product View
Do not plug in your cleaner until you have
completely assembled it per the following
instructions and are familiar with all instructions
and operating procedures.
1Handle
2TurboBrush™ Tool
(select models only)
3 Tank Release Button
4 Carry Handle
5 Lid Release Button
6Cyclonic Filter Separator
& Dust Screen
7Bottom Easy Empty™
Dirt Tank
8 Post-Motor Filter
9 Height Adjustment Knob
10 Furniture Protection Guard
11Powerfoot
12 Cable Clip
13 Upper Hose Wrap
14 Dusting Brush
15 Stretch Hose
16Quick Release®
Cable Wrap
17 Crevice Tool
18 Extension Wand
19 Extension Wand Clip
20 Power Switch
21 Power Cable
22 Handle Release Pedal
23 Hose Wand
24 Hose Wand Base
25 Foot Hose
26 Crevice Tool
27 Dusting Brush
28 Extension Wand
29TurboBrush™ Tool
(select models only)
30Post Motor Febreze™ Filter*
(Select models only)
B Assembly
The only tool you’ll need to assemble
your vacuum cleaner is a Phillips head
screwdriver.
B1-Attach handle to vacuum
1. Locate the vacuum handle and remove the
screw packet taped to the handle. The screw
packet contains two screws of equal length.
2. Stand the vacuum upright and slide the
base of the handle firmly into the opening
at the top of the vacuum body.
3. Check to be sure the handle is fitted to
the vacuum body. If there are any gaps
between the handle and the vacuum base,
continue to push the handle firmly into the
base until the handle is flush.
4. Insert the two screws from the screw
packet into the existing holes. Push each
screw firmly into the hole before beginning
to secure the screw with a Phillips head
screwdriver. If the handle is aligned properly
on the vacuum base, you should be able to
push the screw almost entirely into the hole
until only the screw head is visible. Tighten
the screw with a Phillips head screwdriver
by rotating the screw clockwise.
6
www.BISSELL.com
B2-Attach vacuum hose,
clips & tools
1. Attach the extension wand clip by inserting the clip into the back of the vacuum base
and twisting clockwise. Mount the extension
wand (with crevice tool inside) on the back
of the vacuum.
2. Snap the upper cable wrap into the socket
located above the extension wand clip. Wrap
the power cable around the cable wrap clips.
3. Attach the Twist ‘n Snap™ hose by lining
up the tabs on the cuff with the corresponding notches on the back of the vacuum.
Twist the Twist ‘n Snap hose clockwise to
lock the hose into place.
4. Slide the end of the hose wand into the
hose wand base, and fold the hose over the
upper hose wrap.
Note: The powerfoot will not suction
properly unless the hose wand is firmly
attached.
5. Slide the dusting brush into the opening
below the upper hose wrap.
6. The TurboBrush™ Tool (for select models)
secures to the back of the handle in the
mount above the Upper Hose Wrap.
Before using your vacuum, make sure that the dirt
tank is in the locked position and that both filters
(pre-motor and post-motor) are in place. Do not
operate your vacuum without these filters.
The rotating floor brush continues to rotate while
tools are in use. To reduce the risk of injury from
moving parts, always move the cleaner with the
carrying handle at the back of the cleaner. Always place vacuum
cleaner on floor with handle in upright position when using tools.
Never place your fingers under the cleaner when it is running.
Never place powerfoot on furniture or uneven surfaces. Do not
place vacuum cleaner close enough to objects to pull them into
rotating brush.
While vacuuming, certain carpets and low humidity conditions may
generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply.
The floor brush will continue to rotate while you use
your vacuum for above floor cleaning. To prevent
carpet damage, do not lean on the vacuum or let the
powerfoot tilt forward.
*Febreze™ and related trademarks are owned by The Procter & Gamble
Company, Cincinnati, Ohio and used under license by BISSELL Homecare, Inc.
C Operations
Power switch
The Power switch is located on the left side
of the vacuum. Push the rocker switch “ON”
(I) to vacuum, and “OFF” (O) when cleaning
is complete.
C1-Handle position
Press the handle release pedal with your
foot to place your vacuum into one of three
cleaning positions.
1. Upright– For storage and above floor
cleaning with tools.
2. Normal cleaning – Press handle release
household floor cleaning tasks.
3. Low cleaning –With the vacuum in
normal cleaning position, press handle
release pedal again, use for reaching under
low furniture such as tables, chairs or beds.
C2-Height adjustment
There are five height settings available for
various floor surfaces. Turn the dial on the
foot of the cleaner to the desired setting.
Transporting cleaner
1. To move your cleaner from room to
room, put the handle in the upright position,
tilt the cleaner back on its rear wheels and
push forward.
2. The cleaner can also be moved by using
the carrying handle.
Special tools
Your BISSELL vacuum is not only a powerful
carpet and rug vacuum cleaner, it’s also
a versatile above floor vacuum cleaner when
you select one of the special tools.
1. Raise handle to upright position.
2. Grasp the hose wand and separate from
the hose wand base.
3. Attach tools by firmly pushing onto
vacuum hose or extension wand
Crevice tool – Use in tight narrow spaces.
Dusting Brush – Use brush to dust
furniture, blinds, books, lamps, shelves and
baseboards.
Extension wand – Use with desired
attachment for a longer reach.
TurboBrush™ Tool (select models only) –
Lowest setting – For low pile carpet or bare Use rotating brush action for small flat
floors. To pick up debris, it may be necessary areas such as stairs and cushions. Press
to move up one setting.
gently down and pull toward you in a
raking motion; too much pressure will
Medium setting – For medium pile carpet.
cause the brush to stop rotating.
Highest setting – For high pile and most
shag carpet.
NOTE: For optimal carpet cleaning
performance, adjust to the lowest practical
setting. If your cleaner is difficult to push,
adjust to the next higher setting.
If the dial is difficult to turn, tilt the cleaner
back slightly to take the weight off the foot
while turning.
Filters
Your BISSELL vacuum comes with a post
motor filter. For cleaning, remove the filter
from the filter tray.
For optimal cleaning performance, check
the pre-motor filter at least once a month
and clean or replace as needed.
The inner cyclone filter is located in the dirt
container. Follow instructions on page 7 for
maintenance and care.
» Hair, string and small objects can block the vacuum hose
or tools. Check them occasionally for obstructions.
» Before cleaning under low furniture, check area first
for objects that might harm the unit or block the
vacuum hose.
» Your vacuum features a Quick Release cable wrap.
To remove the power cable quickly and easily, rotate
the upper cable wrap toward the floor and slip the
power cable off the upper and lower cable wraps.
www.BISSELL.com
7
Power cable storage
When you have finished using your BISSELL
vacuum, return it to the upright position and
store the power cable.
1. Turn vacuum cleaner off.
2. Unplug power cable by grasping the
polarized plug (NOT the cable) and
disconnect from socket.
3. Wrap power cable around cable wraps
located on the back of the vacuum.
4. Clip molded plug to power cable to
secure.
C3-Empty dirt tank
The dirt tank needs to be emptied when
the dirt reaches the “Full” line on the side
of the tank.
1. Unplug cleaner from electrical socket.
2. Remove the Easy Empty dirt tank from
the vacuum base by pushing the tank
release button.
Use only genuine BISSELL replacement
filters in your BISSELL vacuum.
1. Unplug the cleaner from electrical socket.
2. Remove the Easy Empty dirt tank.
3. With the bottom of Easy Empty dirt
tank open, reach up into the dirt cup and
grasp the cyclone. Twist the filter cyclone
clockwise to unlock and pull straight down
to remove.
4. Locate the snaps on the top of the filter
cyclone. Squeeze the clips and pull up to
remove from the handle.
5. Separate the cyclone from the filter by
pulling them apart.
6. Remove the filter screen, brush off any
large debris and rinse under water. Make sure
the screen is dry before replacing.
7. The filter is washable and can be rinsed
under water. It is best to tap off large debris
prior to rinsing under water. Make sure the
filter is dry before replacing.
8. Replace the filter cyclone following these
3. Hold the dirt tank over a garbage contain- steps.
er. Press the bottom lid release button on the a. Replace screen on filter
back of the dirt tank to empty dirt.
b. Fit together the filter and the upper
4. Mount the Easy Empty dirt tank back on
cyclone by setting it in place
the vacuum base.
c. Slide the filter onto the tool handle
NOTE: The dirt tank may be washed in
and make sure it clips into place
warm water with a mild detergent. Make
d. Line up the arrow on the back of the
sure it is completely dry before replacing.
dirt container to the arrow on the filter
cyclone and slide the filter cyclone into
the tank
D Care & Storage
e. Twist counterclockwise to lock
into place
To maintain maximum cleaning performance,
the following maintenance steps must be
NOTE: More frequent filter cleaning or
performed:
replacing may be necessary if you are
vacuuming new carpet, fine dust, or have
allergy concerns. Follow the instructions
D1-Clearing the inner
on the following pages to perform these
cyclone filter
simple maintenance steps.
Check the inner cyclone filter after every
use for build up or clogs. For optimal
performance, it is recommend to clean
the inner cyclone filter after every use.
To reduce the risk of electric shock, turn power switch
off and disconnect plug from electrical socket
before performing maintenance or care.
Do not operate cleaner with damp or wet filters
or without all filters in place.
8
www.BISSELL.com
»W
hen replacing the inner filter
cyclone after cleaning, open
the lid to help guide the inner
cyclone into the grooves at the
top of the tank.
D2-Replacing the
post-motor filter
Use only a genuine BISSELL replacement
post-motor filter in your BISSELL vacuum.
1. Unplug the cleaner from electrical socket.
D4-Replace drive belt
Use only a genuine BISSELL style 9
replacement belt (#203-1093) in your
BISSELL vacuum.
1. Unplug cleaner from electrical socket.
2. With rotating floor brush removed from
vacuum cleaner (steps 1-4 of Check rotating
floor brush and drive belt), grasp old drive
belt and remove from motor pulley. Discard
3. When the filter becomes dirty, remove the old drive belt.
filter from the bottom of the tray and clean
3. Place new drive belt over motor pulley
or replace the filter. (Tip: flip the filter tray
and stretch other end over rotating floor
over to access the filter).
brush in the space between the bristles.
2. To access the post-motor filter, remove
the filter tray located below the Easy Empty
dirt tank.
D3-Checking rotating floor
brush and drive belt
You should check your vacuum cleaner’s
rotating floor brush and drive belt regularly
for wear or damage. You should also clean
the brush and brush ends of strings, hair and
carpet fibers. These can wrap around the
brush and hamper its ability to effectively
clean your carpet. Also remove any debris
that has accumulated under the brush cover.
1. Unplug cleaner from electrical socket.
2. Place handle in low position and turn
vacuum cleaner over so bottom side is up.
3. Remove the seven screws with a Phillips
head screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends
and lift straight out of the vacuum foot. Slip
off the belt.
5. Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts or
stressed areas, and replace if necessary (see
instructions on following page).
8. Check air passageway for obstructions.
Remove debris from this area.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center itself
on rotating brush.
6. Reposition the brush cover and screw all
seven screws back into place.
D5-Clearing a clog
Low suction or poor pickup may be due to
a clog in the vacuum cleaner. If you notice
a change in the sound of the motor or a
reduction in the spinning action, check for
clogs.
1. Unplug cleaner from electrical socket.
2. Remove Easy Empty dirt tank from vacuum base and empty dirt and debris.
3. Remove inner cyclone filter from Easy
Empty dirt tank (see page 9) and check for
debris build-up or clogs in the upper tank.
4. Check the suction inlet for a clog.
5. Grasp the hose wand to separate from
the hose wand base. Check for a clog in the
base, the wand or within the hose.
6. Remove the screw attaching the hose
wand base to the vacuum. Straighten the
hose wand base and check for clogs with a
long, narrow object such as a broom stick.
Do not use sharp objects like a clothes
hanger, as these may puncture the hose.
7. If the clog persists, follow the instructions
for Checking the rotating floor brush on
page 10 and inspect the air passageway for
obstructions.
www.BISSELL.com
9
Troubleshooting
Problem
Possible causes
Remedies
Vacuum
cleaner won’t
turn on
Power cable not plugged in
Check electrical plug
Blown fuse/tripped breaker
Check/replace fuse or reset breaker
Incorrect height adjustment
Adjust powerfoot to correct height setting
Hose not attached to suction
opening
Grasp the hose wand and firmly
push into the hose wand base
Crack or hole in hose
Check hose and replace if needed
Broken or worn drive belt
Replace drive belt, see page 11
Rotating floor brush bristles worn
Replace brush
Rotating floor brush jammed
Remove brush and clean debris from
brush ends, see page 10
Clog in vacuum
Follow instructions on page 12 for
clearing clogs
Dirt tank full
Empty dirt tank
Dirt tank or upper tank not
installed properly
Position correctly and lock in place
Filters are dirty
Check and clean or replace pre-motor
and post-motor filters, see pages 9, 10
Crack or hole in hose
Check hose and replace if needed
Clog in vacuum
Follow instructions on page 12 for
clearing clogs
Dirt tank full
Empty dirt tank
Dirt tank or upper tank not
installed properly
Position correctly and lock in place
Filters are dirty
Check and clean or replace pre-motor
and inner filter cyclone see pages 8 & 9
Vacuum
cleaner is difficult to push
Incorrect height adjustment
Adjust powerfoot to correct
height setting
Visible dirt
escaping from
cleaner
Dirt tank full
Empty dirt tank
Filters missing or installed
incorrectly
Check inner filter cyclone and postmotor filters for correct installation
Vacuum
cleaner won’t
pick up dirt
Tool won’t
pick up dirt
Please do
not return
this product
to the store.
10
WARNING
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical socket before
performing maintenance or troubleshooting checks.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to be
of service. Contact Customer Care listed on page 12.
www.BISSELL.com
Replacement Parts
These items are available for purchase as accessories for your BISSELL vacuum:
To purchase visit www.BISSELL.com.
PART #
PART NAME
PART #
PART NAME
203-1093
Style 9 Drive Belt
(2-Pack)
160-1219
Hose Assembly
1111E
Filter pack
(includes two post-motor
Febreze™ filters)
160-1220
Filter Cyclone
(includes screen)
160-1218
Post motor (non-scented)
Accessories
These items are available for purchase as accessories for your BISSELL vacuum:
To purchase visit www.BISSELL.com.
PART #
PART NAME
PART #
PART NAME
203-1748
TurboBrush™ Pet Tool
203-1056
Crevice Tool
203-2666
Extension Wand
203-1527
Dusting Brush
160-0064
6-inch TurboBrush™ Tool
*Not all parts are included with every model
www.BISSELL.com
11
Consumer Guarantee
This Guarantee only applies outside of the USA and Canada. It is
provided by BISSELL International Trading Company BV (“BISSELL”).
This Guarantee is provided by BISSELL. It gives you specific rights.
It is offered as an additional benefit to your rights under law. You
also have other rights under law which may vary from country
to country. You can find out about your legal rights and remedies
by contacting your local consumer advice service. Nothing in this
Guarantee will replace or lessen any of your legal rights or remedies.
If you need additional instruction regarding this Guarantee or have
questions regarding what it may cover, please contact BISSELL
Consumer Care or contact your local distributor.
This Guarantee is given to the original purchaser of the product from
new and is not transferable. You must be able to evidence the date
of purchase in order to claim under this Guarantee.
Limited Two-Year Guarantee
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below,
BISSELL will for two years from the date of purchase by the
original purchaser repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge, any
defective or malfunctioning part or product.
BISSELL recommends that the original packaging and evidence of
the date of purchase be kept for the duration of the Guarantee
period in case the need arises within the period to claim on the
Guarantee. Keeping the original packaging will assist with any
necessary re-packaging and transportation but is not a condition
of the Guarantee.
If for your product is replaced by BISSELL under this Guarantee,
the new item will benefit from the remainder of the term of this
Guarantee (calculated from the date of the original purchase).
The period of this Guarantee shall not be extended whether or
not your product is repaired or replaced.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE GUARANTEE
An unauthorised repair (or attempted repair) will void this Guarantee
whether or not damage has been caused by that repair/attempt.
Removing or tampering with the Product Rating Label on the
product or rendering it illegible will void this Guarantee.
SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT
LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING
WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS
INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR
DISAPPOINTMENT. SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
BISSELL DOES NOT EXCLUDE OR LIMIT IN ANY WAY ITS LIABILITY FOR
(A) DEATH OR PERSONAL INJURY CAUSED BY OUR NEGLIGENCE OR THE
NEGLIGENCE OF OUR EMPLOYEES, AGENTS OR SUBCONTRACTORS; (B)
FRAUD OR FRAUDULENT MISREPRESENTATION; (C) OR FOR ANY OTHER
MATTER WHICH CANNOT BE EXCLUDED OR LIMITED UNDER LAW.
Consumer Care
If your BISSELL product should require
service or to claim under our Limited
Two-Year Guarantee, please visit:
Website or E-mail:
www.BISSELL.com
For UK inquiries:
Telephone: 0844.888.6644
Monday – Thursday 9am - 5pm
Friday 9am - 4pm
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough, Berkshire, SL1 4QT
United Kingdom
This Guarantee applies to products used for personal domestic use and
not commercial or hire purposes. Consumable components such as
filters, belts and mop pads, which must be replaced or serviced by the
user from time to time, are not covered by this Guarantee.
This Guarantee does not apply to any defect arising from fair wear
and tear. Damage or malfunction caused by the user or any third
party whether as a result of accident, negligence, abuse, neglect, or
any other use not in accordance with the User Guide is not covered
by this Guarantee.
Visit the BISSELL website:
www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: _____________
Please record your Purchase Date: _____________
NOTE: Please keep your original sales receipt. It
provides proof of the date of purchase in the event
of a Guarantee claim. See Guarantee for details.
©2014 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-4322 Rev 08/14 RevA
Visit our website at: www.BISSELL.com
ENERG
Y IJA
енергиR ενεργεια IE IA
●
1401 Series
PowerForce 300
A
B
C
D
D
E
F
G
ENERGIA - ЕНЕРГИЯ - ΕΝΕΡΓΕΙΑ
ENERGIJA - ENERGY - ENERGIE - ENERGI
44
kWh/annum
ABCDEFG
86.8dB
ABCDEFG
ABCDEFG
665/2013 - I
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement