advertisement
www.philips.com/welcome
EN User manual
Customer care and warranty
Troubleshooting & FAQs
1
28
33
274E5
Table of Contents
1. Important ................................................1
1.1 Safety precautions and maintenance ...1
1.2 Notational Descriptions .............................2
1.3 Disposal of product and packing material ................................................................3
2. Setting up the monitor .........................4
2.1 Installation ...........................................................4
2.2 Operating the monitor ...............................6
2.3 MHL (Mobile High-Definition Link) introduction .......................................................9
3. Image Optimization .............................10
3.1 SmartImage Lite ...........................................10
3.2 SmartContrast ..............................................11
3.3 Philips SmartControl Lite .......................11
4. Technical Specifications ......................17
4.1 Resolution & Preset Modes...................21
5. Power Management ............................22
6. Regulatory Information ......................23
7. Customer care and warranty ...........29
7.1 Philips’ Flat Panel Monitors Pixel
Defect Policy ..................................................29
7.2 Customer Care & Warranty .................31
8. Troubleshooting & FAQs ...................34
8.1 Troubleshooting ...........................................34
8.2 SmartControl Lite FAQs .........................35
8.3 General FAQs ...............................................36
8.4 MHL FAQs ......................................................38
1. Important
1. Important
This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor.
The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase, dealer’s name and model and production number of the product.
1.1 Safety precautions and maintenance
Warnings
Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your computer monitor.
Operation
• Please Keep the monitor out of direct sunlight, very strong bright lights and away from any other heat source. Lengthy exposure to this type of environment may result in discoloration and damage to the monitor.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the monitor, make sure the power plug and outlet are easily accessible.
• If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation.
1
• Please use approved power cord provided by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer
Care Consumer Information Center)
• Do not subject the monitor to severe vibration or high impact conditions during operation.
• Do not knock or drop the monitor during operation or transportation.
Maintenance
• To protect your monitor from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel.
• Unplug the monitor if you are not going to use it for an extensive period of time.
• Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor.
• To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment.
• If your monitor gets wet, wipe it with dry cloth as soon as possible.
• If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center.
• Do not store or use the monitor in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your monitor and use it for a longer lifetime, please use the monitor in a location that falls within the following temperature and humidity ranges.
1. Important
• Temperature: 0-40°C 32-95°F
• Humidity: 20-80% RH
• IMPORTANT: Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your monitor will display unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”, also known as
“after-imaging” or “ghost imaging”, on your screen.
"Burn-in", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the
“burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.
Warning
Failure to activate a screen saver, or a periodic screen refresh application may result in severe
“burn-in” or “after-image” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty.
Service
• The casing cover should be opened only by qualified service personnel.
• If there is any need for any document for repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information
Center")
• For transportation information, please refer to "Technical Specifications".
• Do not leave your monitor in a car/trunk under direct sun light.
Note
Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed.
1.2 Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings. They are used as follows:
Note
This icon indicates important information and tips that help you make better use of your computer system.
Caution
This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.
Warning
This icon indicates the potential for bodily harm and tells you how to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority.
2
1. Important
1.3 Disposal of product and packing material
Waste Electrical and Electronic Equipment-
WEEE
This marking on the product or on its packaging illustrates that, under European
Directive 2002/96/EC governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection.
To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product.
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into mono materials.
Please find out about the local regulations on how to dispose of your old monitor and packing from your sales representative.
Taking back/Recycling Information for
Customers
Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities.
From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled. At
Philips, end-of-life management primarily entails participation in national take-back initiatives and recycling programs whenever possible, preferably in cooperation with competitors, which recycle all materials (products and related packaging material) in accordance with all
Environmental Laws and taking back program with the contractor company.
Your display is manufactured with high quality materials and components which can be recycled and reused.
To learn more about our recycling program please visit http://www.philips.com/sites/philipsglobal/ about/sustainability/ourenvironment/ productrecyclingservices.page
3
2. Setting up the monitor
2. Setting up the monitor
2.1 Installation
Package contents
274E5
Install base stand
1. Place the monitor face down on soft and smooth surface taking care to avoid scratching or damaging the screen.
AC/DC Adapter
Audio cable (optional)
VGA (optional)
2. Hold the base stand with both hands and firmly insert the base stand into the base column.
(1) Gently attach the base to the base column until the latch locks the base.
(2) Use your fingers to tighten the screw located at the bottom of the base, and secure the base to the column tightly.
2
Cable management DVI (optional)
Note
Use only the AC/DC adapter model: Philips
ADPC1945 (274E5QSB/QHSB),Philips
ADPC1965 (274E5QHAW/QHAB)
1
4
2. Setting up the monitor
Connecting to your PC
Model 274E5QSB:
1
2
3
3 2 1
4
Model 274E5QHSB:
1
3
2
4
3 2
1
6
5
AC/DC power input
VGA input
DVI-D input
Kensington anti-theft lock
Model 274E5QHAB, 274E5QHAW:
1
3
2
6
4
3
MHL
2
1
7
5
AC/DC power input
VGA input
HDMI input
HDMI or MHL input(option)
HDMI audio output
Kensington anti-theft lock
Connect to PC
1. Connect the power cord to the back of the monitor firmly.
2. Turn off your computer and unplug its power cable.
3. Connect the monitor signal cable to the video connector on the back of your computer.
4. Plug the power cord of your computer and your monitor into a nearby outlet.
5. Turn on your computer and monitor. If the monitor displays an image, installation is complete.
AC/DC power input
VGA input
HDMI input
HDMI or MHL input(option)
Earphone output
Audio input
Kensington anti-theft lock
5
2. Setting up the monitor
2.2 Operating the monitor
Front view product description
Model 274E5QSB, 274E5QHSB:
Model 274E5QHAB, 274E5QHAW:
5
7 3 6 4 2
Switch monitor’s power ON and
OFF .
Access the OSD menu.
Return to previous OSD level.
Change display format.
Adjust the OSD menu.
Change the signal input source.
SmartImage Lite. There are three modes to be selected: Standard,
Internet and Game.
5
7 3 6 4 2
Switch monitor’s power ON and
OFF .
Access the OSD menu.
Return to previous OSD level.
Adjust the speaker volume.
Adjust the OSD menu.
Change the signal input source.
SmartImage Lite. There are three modes to be selected: Standard,
Internet and Game.
6
2. Setting up the monitor
Description of the On Screen Display
What is On-Screen Display (OSD)?
On-Screen Display (OSD) is a feature in all
Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below:
Model 274E5QSB:
Model 274E5QHSB,274E5QHAB,274E5QHAW:
Basic and simple instruction on the control keys
In the OSD shown above, you can press buttons at the front bezel of the monitor to move the cursor, and press OK button to confirm the choice or change.
7
2. Setting up the monitor
The OSD Menu
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
Main menu
Input
Picture
Audio
Color
Language
OSD Settings
Setup
Sub menu
VGA
DVI (available for selective models)
HDMI (available for selective models)
MHL-HDMI (available for selective models)
Picture Format
Brightness
Mute
Color Temperature
Wide Screen, 4:3
0~100
Contrast 0~100
SmartResponse Off, Fast, Faster, Fastest
(available for selective models)
SmartContrast On, Off
Pixel Orbiting On, Off
(available for selective models)
Over Scan On, Off
(available for selective models)
Volume
0~100
(available for selective models)
Stand-Alone On, Off
On, Off
6500K, 9300K sRGB
User Define Red: 0~100
Green: 0~100
Blue: 0~100
English, Deutsch, Español, Ελληνική, Français,
Italiano, Maryar,Nederlands, Português,
Português do Brazil,Polski,Русский ,Svenska,
Suomi,Türkçe,Čeština, Українська, 简体中文,
繁 體中文,日本語,한국어
Horizontal 0~100
Vertical 0~100
Off, 1, 2, 3, 4 Transparency
OSD Time Out
Auto
5s, 10s, 20s, 30s, 60s
H.Position
0~100
V.Position
Phase
Clock
Resolution Notification
Reset
Information
0~100
0~100
0~100
On, Off
Yes, No
Resolution notification
This monitor is designed for optimal performance at its native resolution,
1920×1080@60Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920×1080@60Hz for best results.
Display of the native resolution alert can be switched off from Setup in the OSD (On
Screen Display) menu.
Physical Function
Tilt
8
2. Setting up the monitor
2.3 MHL (Mobile High-Definition
Link) introduction
What is it?
Mobile High Definition Link (MHL) is a mobile audio/video interface for directly connecting mobile phones and other portable devices to high-definition displays.
An optional MHL cable allows you to simply connect your MHL capable mobile device to this large Philips MHL display, and watch your
HD videos come to life with full digital sound.
Now not only you can enjoy your mobile games, photos, movies, or other apps on its big screen, you can simultaneously charge your mobile device so you never run out of power half way.
How do I use the MHL function?
To use the MHL function, you need an MHL-
Certified mobile device. To find a list of MHLcertified devices, visit the official MHL website
(http://www.mhlconsortium.org)
You also need a optional MHL certified special cable in order to use this function.
How does it work? (how do I connect?)
Connect the Optional MHL cable to the mini
USB port on the mobile device side, and the
[MHL-HDMI] marked port on the monitor side.
You are now ready to view the images on your big screen display and operate all function on you the mobile device such as internet surfing, game playing, photo browsing…etc. if your monitor has speaker function, then you will be able to hear accompanying sound too. When the MHL cable is disconnected or the mobile device is turned off, the MHL function will be automatically disabled.
MHL-HDMI
MHL
Note
• The port marked [MHL-HDMI] is the only port on the monitor that supports the MHL function when the MHL cable is used. Note that the MHL certified cable is different than a standard HDMI cable.
• A mobile device with MHL certification must be purchased separately
• You may have to manually switch the monitor to MHL-HDMI mode in order to activate the monitor, if you have other devices already working and connected to available inputs
• Standby/Off energy saving of ErP is not applicable for the MHL charging functionality
9
3. Image Optimization
3. Image Optimization
3.1 SmartImage Lite
What is it?
SmartImage Lite provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage Lite delivers great optimized monitor performance.
Why do I need it?
You want a monitor that delivers optimized display all your favorite types of content,
SmartImage Lite software dynamically adjust brightness, contrast, color and sharpness in real time to enhance your monitor viewing experience.
How does it work?
SmartImage Lite is an exclusive, leading edge
Philips technology that analyzes the content displayed on your screen. Based on a scenario you select, SmartImage Lite dynamically enhances the contrast, color saturation and sharpness of images to enhance the contents being displayed - all in real time with the press of a single button.
How to enable SmartImage Lite?
1. Press to launch the SmartImage Lite on screen display;
2. Keep pressing to toggle between
Standard, Internet, Game.
10
3. The SmartImage Lite on screen display will remain on screen for 5 seconds or you can also press OK button to make confirmation.
4. When SmartImage Lite is enabled, the sRGB scheme is disabled automatically. To use sRGB you need to disable SmartImage
Lite with the button at the front bezel of your monitor.
Except using key to scroll down, you can also press buttons to choose and press
OK button to confirm selection and close the
SmartImage Lite OSD.
There are three modes to be selected: Standard,
Internet, Game.
• Standard: Enhances text and dampens brightness to increase readability and reduce eye strain. This mode significantly enhances readability and productivity when you're working with spreadsheets, PDF files, scanned articles or other general office applications.
• Internet: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors.
• Game: Turn on over drive circuit for best response time, reduce jaggy edges for fast moving objects on screen, enhance contrast ratio for bright and dark scheme, this profile delivers the best gaming experience for gamers.
3. Image Optimization
3.2 SmartContrast
What is it?
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds.
Why do I need it?
You want the very best visual clarity and viewing comfort for every type of content.
SmartContrast dynamically controls contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of your monitor.
How does it work?
When you activate SmartContrast, it will analyse the content you are displaying in real time to adjust colors and control backlight intensity. This function will dynamically enhance contrast for a great entertainment experience when viewing videos or playing games.
3.3 Philips SmartControl Lite
The new SmartControl Lite software by Phillips allows you to control your monitor via an easy to use on-screen graphic interface. Complicated adjustments are a thing of the past as this user friendly software guides you through finetuning resolution, Color calibration, Clock/Phase adjustments, RGB White point adjustment, etc.
Equipped with latest technology in core algorithm for fast processing and response, this
Windows 7 compliant eye catching animated
Icon based software is ready to enhance your experience with Philips monitors!
Installation
• Follow the instruction and complete the installation.
• You can launch after installation is completed.
• If you want to launch later, you can either click the shortcut on desktop or toolbar.
First launch -Wizard
• The first time after installation of
SmartControl Lite, it will automatically go to Wizard for first time launch.
• The wizard will guide you through adjustment your monitor performance step by step.
• You can go to Plug-in menu to launch wizard later on as well.
• You can adjust more options without wizard by Standard pane.
11
3. Image Optimization
Start with Standard pane:
Adjust menu:
• Adjust Menu allow you to adjust Brightness,
Contrast, Focus, Position and Resolution.
• You can follow the instruction and do the adjustment.
• Cancel prompts user if you want to cancel installation.
12
3. Image Optimization
Color menu:
• Color Menu allow you to adjust RGB,
Black Level, White Point, Color Calibration, and SmartImage Lite (Please refer to
SmartImage Lite section).
• You can follow the instruction and do the adjustment.
• Refer to below table for sub-menu item base on your input.
• Example for Color Calibration:
13
1. "Show Me" starts color calibration tutorial.
2. Start - starts the 6-step color calibration sequence.
3. Quick View loads the before/after images.
4. To return to Color home pane, click the
Cancel button.
5. Enable color calibration - by default is on.
If unchecked, does not allow for color calibration to happen, dimes out start and quick view buttons.
6. Must have patent info in calibration screen.
3. Image Optimization
First color Calibration Screen:
• Previous button is disabled until the second color screen.
• Next goes to the succeeding target
(6-targets).
• Final next goes File>Presets pane.
• Cancel closes the UI and returns to the plug in page.
SmartImage Lite
Allows user to change setting for better display setting based on content.
When Entertainment is set, SmartContrast and
SmartResponse are enabled.
Options>Preferences - Will only be active when selecting Preferences from the dropdown Options menu. On a non-supported display capable of DDC/CI, only the Help and
Options tabs are available.
• Displays current preference settings.
• A checked box enables the feature. The check box is a toggle.
• Enable Context Menu on desktop is checked (On) by default. Enable Context menu displays SmartControl Lite selections for Select Preset and Tune Display in the desktop right-click context menu. Disabled removes SmartControl Lite from the right click context menu.
• Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl Lite. A right click on the task tray icon displays the menu options for Help, Technical Support,
Check for Update, About, and Exit. When
Enable task tray menu is disabled, the task tray icon will only display EXIT.
• Run at Startup is checked (On) by default.
When disabled, SmartControl Lite will not launch at start or be in the task tray. The only way to launch SmartControl Lite is either from the desktop short cut or from the program file. Any preset set to run at startup will not load when this box is unchecked (Disabled).
• Enable transparency mode (Windows 7,
Vista, XP). Default is 0% Opaque.
14
3. Image Optimization
Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-supported display capable of
DDC/CI, only the Help and Options tabs are available. All other SmartControl Lite tabs are not available.
Help>User Manual - Will only be active when selecting User Manual from the drop-down
Help menu. On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.
• Display the Source instruction pane and current input source setting.
• On single input displays, this pane will not be visible.
Options>Audio - Will only be active when selecting Audio from the drop-down Options menu.
On a non-supported display capable of DDC/
CI, only the Help and Options tabs are available.
Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-supported display capable of
DDC/CI, only the Help and Options tabs are available.
15
3. Image Optimization
Context Sensitive menu
The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the Options>Preferences pane, then the menu will be visible.
• Technical Support - displays the tech support page.
• Check for Update - takes the user to PDI
Landing and checks the user’s version against the most current available.
• About - Displays detailed reference information: product version, release information, and product name.
• Exit - Close SmartControl Lite.
To run SmartControl Lite again either select
SmartControl Lite from Program menu, doubleclick the desktop PC icon or restart the system.
The Context Menu has four entries:
• SmartControl Lite - When selected the
About Screen is displayed.
• Select Preset - Provides a hierarchical menu of saved presets for immediate use.
A check mark shows the currently selected preset. Factory Preset can also be called from the drop down menu.
• Tune Display - Opens the SmartControl
Lite control panel.
• SmartImage Lite - Check current settings,
Standard, Internet, Game.
Task Tray Menu Enabled
The task tray menu can be displayed by rightclicking on the SmartControl Lite icon from the task tray. Left Click will launch the application.
Task Tray Menu Disabled
When the Task Tray is disabled in the preference folder, only the EXIT selection is available.
To completely remove SmartControl Lite from the task tray, disable Run at Startup in
Options>Preferences.
The task tray has five entries:
• Help - Access to User Manual file: Open
User Manual file using the default browser window.
16
4. Technical Specifications
4. Technical Specifications
Picture/Display
Monitor Panel Type
Backlight
Panel Size
Aspect Ratio
Pixel Pitch
Brightness
SmartContrast
Contrast Ratio (typ.)
Response Time (typ.)
SmartResponse (available for selected models)
Optimum Resolution
Viewing Angle
Picture Enhancement
Display Colors
Vertical Refresh Rate
Horizontal Frequency
MHL sRGB
Connectivity
IPS LCD
LED
27" W (68.6cm)
16:9
0.3114 x 0.3114 mm
250 cd/m²
20,000,000:1
1000:1
14ms
5ms
1920x1080@60Hz
178° (H) / 178° (V) @ C/R > 10
SmartImage Lite
16.7M
56Hz - 76Hz
30kHz - 83kHz
1080P@30Hz
YES
Signal Input
Audio In/Out
Input Signal
274E5QSB: VGA(Analog), DVI(Digital,HDCP)
274E5QHSB, 274E5QHAB, 274E5QHAW: VGA(Analog),
HDMI(Digital,HDCP), MHL-HDMI (Digital, HDCP)
274E5QHAB, 274E5QHAW : PC audio-in, Earphone out
274E5QHSB : HDMI audio out
Separate Sync, Sync on Green
Convenience
274E5QSB, 274E5QHSB,:
User Convenience
274E5QHAB, 274E5QHAW:
OSD Languages
Other Convenience
Plug & Play Compatibility
English, German, Spanish, Greek, French, Italian, Hungarian, Dutch,
Portuguese, Brazil Portuguese, Polish, Russian, Swedish, Finnish,
Turkish, Czech, Ukranian, Simplified Chinese, Traditional Chinese,
Japanese, Korean
Kensington Lock
DDC/CI, sRGB, Windows 8/7/Vista/XP, Mac OSX, Linux
17
4. Technical Specifications
Stand
Tilt
274E5QSB :
Power
On Mode
Sleep (typ.)
Off (typ.)
Power LED indicator
Power Supply
274E5QHSB :
Power
On Mode
Sleep (typ.)
Off (typ.)
Power LED indicator
Power Supply
274E5QHAB, 274E5QHAW:
Power
On Mode
Sleep (typ.)
Off (typ.)
Power LED indicator
Power Supply
Dimension
Product with stand (WxHxD)
Product without stand
(WxHxD)
Weight
Product with stand
Product without stand
Product with packaging
Operating Condition
Temperature range (operation)
Temperature range
(Non-operation)
Relative humidity
MTBF
-5° / +20°
31.1W(typ.)
0.5W
0.3W
On mode: White, Standby/Sleep mode: White (blinking)
External, 100-240VAC, 50-60Hz
31.7W(typ.)
0.5W
0.3W
On mode: White, Standby/Sleep mode: White (blinking)
External, 100-240VAC, 50-60Hz
31.7W(typ.), 45W(max.)
0.5W
0.3W
On mode: White, Standby/Sleep mode: White (blinking)
External, 100-240VAC, 50-60Hz
622 x 470 x 237 mm
622 x 375 x 49 mm
5.1 kg
4.875 kg
7.17 kg
0°C to 40 °C
-20°C to 60°C
20% to 80%
30,000hrs
18
4. Technical Specifications
Environmental
ROHS
EPEAT
Packaging
Specific Substances
Energy Star
Compliance and standards
Regulatory Approvals
Cabinet
Color
Finish
YES
Silver (www.epeat.net)
100% recyclable
100% PVC BFR free housing
YES
CE Mark, FCC Class B, GOAST, SEMKO, TCO Certified, ETL,
BSMI, ISO9241-307
274E5QHAW: white/274E5Q: Black/Black Cherry, or other color options as applicable in your region
Glossy
Note
1. EPEAT Gold or Silver is valid only where Philips registers the product. Please visit www.epeat.net for registration status in your country.
2. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet.
19
4. Technical Specifications
4.1 Resolution & Preset Modes
Maximum Resolution
1920x1080@60Hz (analog input)
1920x1080@60Hz (digital input)
Recommended Resolution
1920x1080@60Hz (digital input)
48.36
60.02
63.89
79.98
55.94
70.64
65.29
67.50
H. freq (kHz) Resolution V. freq (Hz)
31.47
720x400 70.09
31.47
35.00
640x480
640x480
59.94
66.67
37.86
37.50
37.88
46.88
640x480
640x480
800x600
800x600
72.81
75.00
60.32
75.00
1024x768
1024x768
1280x1024
1280x1024
1440x900
1440x900
1680x1050
1920x1080
60.00
75.03
60.02
75.03
59.89
74.98
59.95
60.00
Note
Please notice that your display works best at native resolution of 1920x1080@60Hz. For best display quality, please follow this resolution recommendation.
20
4. Technical Specifications
5. Power Management
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power saving feature:
274E5QSB:
Power Management Definition
VESA
Mode
Active
Video H-sync V-sync Power Used
ON Yes Yes 31.1 W (typ.)
LED Color
White
Sleep OFF
Switch Off OFF
No
-
No
-
0.5 W (typ.)
0.3 W (typ.)
White
(blink)
OFF
274E5QHSB:
Power Management Definition
VESA
Mode
Active
Video H-sync V-sync Power Used
ON Yes Yes 31.7 W (typ.)
LED Color
Sleep OFF
Switch Off OFF
No
-
No
-
0.5 W (typ.)
0.3 W (typ.)
White
White
(blink)
OFF
274E5QHAB, 274E5QHAW :
Power Management Definition
VESA
Mode
Video H-sync V-sync Power Used LED Color
Active ON Yes Yes
31.7 W (typ.)
45 W(max.)
White
Sleep OFF
Switch Off OFF
No
-
No
-
0.5 W (typ.)
0.3 W (typ.)
White
(blink)
OFF
The following setup is used to measure power consumption on this monitor.
• Native resolution: 1920x1080
• Contrast: 50%
• Brightness: 250 nits
• Color temperature: 6500k with full white pattern
Note
This data is subject to change without notice.
21
5. Power Management
6. Regulatory Information
Lead-free Product
Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment. Toxic substances like Lead has been eliminated and compliance with European community’s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle.
Congratulations!
This product is designed for both you and the planet!
TCO Development works for sustainable IT - manufacture, use and recycling of IT products reflecting environmental, social and economic responsibility.
TCO Certified is a third party verified program, where every product model is tested by an accredited impartial test laboratory. TCO
Certified represents one of the toughest certifications for ICT products worldwide.
Some of the Usability features of TCO
Certified Displays:
• Visual Ergonomics for image quality is tested to ensure top performance and reduce sight and strain problems.
Important parameters are Resolution,
Luminance, Contrast, Reflection and Colour characteristics
• Products are tested according to rigorous safety standards at impartial laboratories
• Electric and magnetic fields emissions as low as normal household background levels
• Workload ergonomics to ensure a good physical environment
Some of the Environmental features of TCO
Certified Displays:
• Production facilities have an Environmental
Management System (EMAS or ISO 14001)
• Low energy consumption to minimize climate impact
• Restrictions on Chlorinated and
Brominated flame retardants, plasticizers, plastics and heavy metals such as cadmium, mercury and lead (RoHS compliance)
• Both product and product packaging is prepared for recycling
• The brand owner offers take-back options
Corporate Social Responsibility
• The brand owner demonstrates the product is manufactured under working practices that promote good labour relations and working conditions.
The Criteria Document can be downloaded from our web site. The criteria included in this label have been developed by TCO
Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s
TCO has been involved in influencing the development of IT equipment in a more user and environmentally friendly direction. Our ICT product labeling system began in 1992 and is now requested by users and ICT-manufacturers all over the world.
For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.
For more information, please visit www.tcodevelopment.com
Technology for you and the planet
(Only for selective models)
22
6. Regulatory Infomation
EPEAT
(www.epeat.net)
The EPEAT (Electronic
Product Environmental
Assessment Tool) program evaluates computer desktops, laptops, and monitors based on 51 environmental criteria developed through an extensive stakeholder consensus process supported by US EPA.
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact of its products.
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste EPEAT’S requirement that all registered products meet
ENERGY STAR’s energy efficiency specifications, means that these products will consume less energy throughout their life.
CE Declaration of Conformity
This product is in conformity with the following standards
• EN60950-1:2006+A11:2009+A1:
2010+A12:2011 (Safety requirement of
Information Technology Equipment).
• EN55022:2010(Radio Disturbance requirement of Information Technology
Equipment).
• EN55024:2010 (Immunity requirement of
Information Technology Equipment).
• EN61000-3-2:2006+A1:2009+A2:2009
(Limits for Harmonic Current Emission).
• EN61000-3-3:2008 (Limitation of Voltage
Fluctuation and Flicker) following provisions of directives applicable.
• 2006/95/EC (Low Voltage Directive).
• 2004/108/EC (EMC Directive).
• 2009/125/EC (ErP Directive, EC No.
1275/2008 Implementing Directive for Standby and Off mode power consumption)
And is produced by a manufacturing organization on ISO9000 level.
• ISO9241-307:2008 (Ergonomic requirement, Analysis and compliance test methods for electronic visual displays).
• GS EK1-2000:2011 (GS mark requirement).
• prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display).
• MPR-II (MPR:1990:8/1990:10 Low
Frequency Electric and Magnetic fields).
• TCO CERTIFIED (Requirement for
Environment Labeling of Ergonomics,
Energy, Ecology and Emission, TCO: Swedish
Confederation of Professional Employees) for TCO versions.
23
6. Regulatory Infomation
Energy Star Declaration
(www.energystar.gov)
As an ENERGY STAR ® Partner, we have determined that this product meets the ENERGY STAR ® guidelines for energy efficiency.
Note
We recommend you switch off the monitor when it is not in use for a long time.
Federal Communications Commission (FCC)
Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS
ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked with FCC Logo,
United States Only
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Commission Federale de la Communication
(FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle.
CET appareil produit, utilise et peut émettre des hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer des interférences nuisibles aux communications radio.
24
6. Regulatory Infomation
Cependant, rien ne peut garantir l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures suivantes:
• Réorienter ou déplacer l’antenne de réception.
• Augmenter la distance entre l’équipement et le récepteur.
• Brancher l’équipement sur un autre circuit que celui utilisé par le récepteur.
• Demander l’aide du marchand ou d’un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent
équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE
B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR
DU CANADA.
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification
Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251.
25
6. Regulatory Infomation
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE
OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
S Ø R G V E D P L AC E R I N G E N F O R , AT
NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO
VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ
DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor
Schäden durch Röntgenstrahlen" festgelegten
Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften
über die Bauart von Störstrahlern nach Anlage
III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte
Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN
DIESES GERÄTES DARAUF
ACHTEN, DAß NETZSTECKER UND
NETZKABELANSCHLUß LEICHT
ZUGÄNGLICH SIND.
26
6. Regulatory Infomation
China RoHS
The People's Republic of China released a regulation called "Management Methods for
Controlling Pollution by Electronic Information
Products" or commonly referred to as China
RoHS. All products including CRT and Monitor which are produced and sold for China market have to meet China RoHS request.
EU Energy Label
环保使用期限
此标识指期限(十年),电子信息产品中含有的有
毒有害物质或元素在正常使用的条件下不会发生
外泄或突变, 电子信息产品用户使用该电子信息
产品不会对环境造成严重污染或对其人身、 财
产造成严重损害的期限.
The European Energy Label informs you on the energy efficiency class of this product.
The greener the energy efficiency class of this product is the lower the energy it consumes. On the label, you can find the energy efficiency class, the average power consumption of this product in use and the average energy consumption for
1 year.
Note
The EU Energy Label will be ONLY applied on the models bundling with HDMI and TV tuners.
《废弃电器电子产品回收处理管理条例》提示性
说明
为了更好地关爱及保护地球,当用户不再需要此产
品或产品寿命终止时,请遵守国家废弃电器电子产
品回收处理相关法律法规,将其交给当地具有国家
认可的回收处理资质的厂商进行回收处理。
27
7. Customer care and warranty
7. Customer care and warranty
7.1 Philips’ Flat Panel Monitors Pixel
Defect Policy
Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT Monitor panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT
Monitor panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a monitor may be defective.
Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others. This policy is valid worldwide.
subpixel black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category.
Bright Dot Defects
Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are the types of bright dot defects.
One lit red, green or blue sub pixel.
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue) pixel
Pixels and Sub pixels
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single
Three adjacent lit sub pixels (one white pixel).
28
7. Customer care and warranty
Note
A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
Black Dot Defects
Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. These are the types of black dot defects.
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
BRIGHT DOT DEFECTS
1 lit subpixel
2 adjacent lit subpixels
3 adjacent lit subpixels (one white pixel)
Distance between two bright dot defects*
Total bright dot defects of all types
BLACK DOT DEFECTS
1 dark subpixel
2 adjacent dark subpixels
3 adjacent dark subpixels
Distance between two black dot defects*
Total black dot defects of all types
TOTAL DOT DEFECTS
Total bright or black dot defects of all types
ACCEPTABLE LEVEL
3
1
0
>15mm
3
ACCEPTABLE LEVEL
5 or fewer
2 or fewer
0
>15mm
5 or fewer
ACCEPTABLE LEVEL
5 or fewer
Note
1. 1 or 2 adjacent sub pixel defects = 1 dot defect
2. This monitor is ISO9241-307 compliant (ISO9241-307: Ergonomic requirement, analysis and compliance test methods for electronic visual displays)
29
7. Customer care and warranty
7.2 Customer Care & Warranty
For warranty coverage information and additional support requirement valid for your region, please visit www.philips.com/support website for details. You may also contact your local Philips Customer Care
Center number listed below.
Contact Information for WESTERN EUROPE region:
Country
Germany
United Kingdom
Ireland
Spain
Finland
France
Greece
Italy
Netherlands
Denmark
Norway
Sweden
Poland
Austria
Belgium
Luxembourg
Portugal
Switzerland
ASC
Siemens I&S
Invec Scotland
Invec Scotland
Eatsa Spain
A-novo
A-novo
Allman Hellas
A-novo
E Care
A-novo
A-novo
A-novo
Zolter
Siemens I&S
E Care
E Care
Eatsa Spain
A-novo
Consumer care number
+49 01803 386 853
+44 0207 949 0069
+353 01 601 1161
+34 902 888 785
+358 09 2290 1908
+33 082161 1658
+30 00800 3122 1223
+39 840 320 041
+31 0900 0400 063
+45 3525 8761
+47 2270 8250
+46 08 632 0016
+48 0223491505
+43 0810 000206
+32 078 250851
+352 26 84 30 00
+351 2 1359 1440
+41 02 2310 2116
Price
€ 0.09
Local call tariff
Local call tariff
€ 0.10
Local call tariff
€ 0.09
Free of charge
€ 0.08
€ 0.10
Local call tariff
Local call tariff
Local call tariff
Local call tariff
€ 0.07
€ 0.06
Local call tariff
Local call tariff
Local call tariff
30
7. Customer care and warranty
Contact Information for CENTRAL AND EASTERN EUROPE region:
Country
Belarus
Bulgaria
Croatia
Estonia
Latvia
Lithuania
Romania
Serbia &
Montenegro
Call center
NA
NA
NA
NA
NA
NA
NA
NA
Slovenia NA
NA
Ukraine
NA
NA
Russia
Slovakia
Turkey
NA
NA
NA
Czech Rep. NA
Hungary
NA
NA
ASC
IBA
LAN Service
Renoprom
FUJITSU
“ServiceNet LV” Ltd.
UAB "Servicenet"
Blue Ridge Intl.
Kim Tec d.o.o.
PC H.and
Comel
Topaz-Service Company
CPS
CEEE Partners
Datalan Service
Techpro
Asupport
Serware
Profi Service
Consumer care number
+375 17 217 3386
+359 2 960 2360
+385 1 333 0974
+372 6519900
+371 7460399
+370 7400088
+40 21 2101969
+381 11 20 70 684
+386 1 530 08 24
+380 562320045
+38 044 245 73 31
+7 (495) 645 6746 (for repair)
+7 (495) 645 3010 (for sales)
+421 2 49207155
+90 212 444 4 832
800 100 697
+36 1 2426331
+36 1 814 8080
Contact Information for LATIN AMERICA region:
Country Call center
Brazil
Argentina
Vermont
Consumer care number
0800-7254101
0800 3330 856
Contact Information for China:
China
Consumer care number : 4008 800 008
Contact Information for NORTH AMERICA :
Country
U.S.A.
Call center ASC
EPI - e-center Qwantech
Canada Supercom Supercom
Consumer care number
(877) 835-1838
(800)479-6696
31
7. Customer care and warranty
Contact Information for APMEA region:
Country Call center
Australia NA
New Zealand NA
Hong Kong /
Macau
NA
ASC Consumer care number
AGOS NETWORK PTY LTD 1300 360 386
Visual Group Ltd.
0800 657447
India
Indonesia
South Korea
Malaysia
Pakistan
Singapore
NA
NA
NA
NA
NA
NA
Smart Pixels Technology Ltd.
REDINGTON INDIA LTD
Hong Kong:Tel: +852 2619 9639
Macau:Tel: (853)-0800-987
Tel: 1 800 425 6396
SMS: PHILIPS to 56677
PT. Gadingsari elektronika Prima
Tel: 62 21 75909053, 75909056,
7511530
080-600-6600 PCS One Korea Ltd.
After Market Solutions (CE)
Sdn Bhd
Philips Consumer Service
603 7953 3370
(9221) 2737411-16
Philips Electronics Singapore
Pte Ltd (Philips Consumer Care
Center)
(65) 6882 3999
Taiwan
Thailand
South Africa
United Arab
Emirates
PCCW
Teleservices
Taiwan
NA
NA
NA
FETEC.CO
0800-231-099
Axis Computer System Co., Ltd. (662) 934-5498
Sylvara Technologies Pty Ltd 086 0000 888
AL SHAHD COMPUTER L.L.C 00971 4 2276525
Israel NA Eastronics LTD
Vietnam
Philippines
NA
NA
FPT Service Informatic
Company Ltd.
Glee Electronics, Inc.
1-800-567000
+84 8 38248007 Ho Chi Minh City
+84 5113.562666 Danang City
+84 5113.562666 Can tho Province
(02) 633-4533 to 34,
(02) 637-6559 to 60
Sri Lanka
Bangladesh
Nepal
Cambodia
NA
NA
NA
NA no distributor and/or service provider currently
Distributor: Computer Source
Ltd (warranty buy-out)
Distributor: Syakar Co. Ltd
(warranty buy-out)
Distributor: Neat Technology
Pte Ltd (Singapore) (warranty buy-out)
880-2-9141747, 9127592
880-2-8128848 / 52
977-1-4222395
855-023-999992
32
8. Troubleshooting & FAQs
8. Troubleshooting & FAQs
8.1 Troubleshooting
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact
Philips customer service representative.
Common Problems
No Picture (Power LED not lit)
• Make sure the power cord is plugged into the power outlet and into the back of the monitor.
• First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.
No Picture (Power LED is White)
• Make sure the computer is turned on.
• Make sure the signal cable is properly connected to your computer.
• Make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.
• The Energy Saving feature may be activated
Screen says
Attention
Check cable connection satisfactory, you can do manual adjustments via the OSD menu.
Note
The Auto Function is not applicable in DVI-
Digital mode as it is not necessary.
Visible signs of smoke or sparks
• Do not perform any troubleshooting steps
• Disconnect the monitor from mains power source immediately for safety
• Contact with Philips customer service representative immediately.
Imaging Problems
Image is not centered
• Adjust the image position using the “Auto” function in OSD Main Controls.
• Adjust the image position using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
Image vibrates on the screen
• Check that the signal cable is properly securely connected to the graphics board or PC.
Vertical flicker appears
• Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Start Guide).
• Check to see if the monitor cable has bent pins.
• Make sure the computer is turned on.
AUTO button doesn't function
• The auto function is applicable only in
VGA-Analog mode. If the result is not
• Adjust the image using the “Auto” function in OSD Main Controls.
• Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
Horizontal flicker appears
• Adjust the image using the “Auto” function in OSD Main Controls.
33
8. Troubleshooting & FAQs
• Eliminate the vertical bars using the Phase/
Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
Image appears blurred, indistinct or too dark
• Adjust the contrast and brightness on
On-Screen Display.
An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.
• Uninterrupted display of still or static images over an extended period may cause
"burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burnin", "after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.
• Always activate a moving screen saver program when you leave your monitor unattended.
• Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content.
• Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “after-image” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty.
Image appears distorted. Text is fuzzy or blurred.
• Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.
Green, red, blue, dark, and white dots appears on the screen
• The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.
The "power on" light is too strong and is disturbing
• You can adjust “power on” light using the power LED Setup in OSD main Controls.
For further assistance, refer to the Consumer
Information Centers list and contact Philips customer service representative.
8.2 SmartControl Lite FAQs
Q1. I change the monitor on a PC to a different one and the SmartControl Lite becomes un-usable, what do I do?
Ans.: Restart your PC and see if SmartControl
Lite can work. Otherwise, you will need to remove and re-install SmartControl
Lite to ensure proper driver is installed.
Q2. The SmartControl Lite functions worked well before, but it does not work anymore, what can I do?
Ans.: If the following actions were executed, the monitor driver may need to be reinstalled.
• Changed video graphic adapter to another one
• Updated video driver
• Activities on OS, such as service pack or patch
• Run Windows Update and updated monitor and/or video driver
• Windows was booted with the monitor power off or disconnected.
• To find out, please right click My Computer and click on Properties->Hardware->
Device Manager.
• If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install.
Simply remove SmartControl Lite and re-install it.
Q3. After installing SmartControl Lite, when clicking on SmartControl Lite tab, nothing shows up after a while or a failure message shows, what happened?
34
8. Troubleshooting & FAQs
Ans.: It might be your graphic adaptor is not compatible with the SmartControl Lite. If your graphic adaptor is one of the above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies’ web site.
Install the driver. Remove SmartControl
Lite, and re-install it once more.
If it is still not working, we are sorry that the graphic adaptor is not supported.
Please visit Philips website and check if an updated SmartControl Lite driver is available.
Q4. When I click on Product Information, only partial information is shown, what happened?
Ans.: It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI interface.
Please try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl Lite and re-install it once more.
Attention
Theft mode enabled
Q5. I forgot my PIN for Theft Deterrence
Function. What can I do?
Ans.: Philips Service center has a right to ask for legitimate identification and authorization, in order to establish ownership of the monitor.
Please note that the anti-theft deterrence function is provided as a convenient free option. Managing PIN numbers is the sole responsibility of the individual user or the organization who sets it. In case the
PIN number is forgotten, Philips service center can re-set it for you at a nominal charge after verification of ownership.
Please note that this activity is not covered by standard warranty terms.
8.3 General FAQs
Q1: When I install my monitor what should
I do if the screen shows 'Cannot display this video mode'?
Ans.: Recommended resolution for this monitor: 1920x1080@60Hz.
• Unplug all cables, then connect your PC to the monitor that you used previously.
• In the Windows Start Menu, select Settings/
Control Panel. In the Control Panel
Window, select the Display icon. Inside the
Display Control Panel, select the 'Settings' tab. Under the setting tab, in box labelled
'desktop area', move the sidebar to
1920x1080 pixels.
• Open 'Advanced Properties' and set the
Refresh Rate to 60Hz, then click OK.
• Restart your computer and repeat step
2 and 3 to verify that your PC is set at
1920x1080@60Hz.
• Shut down your computer, disconnect your old monitor and reconnect your Philips
LCD monitor.
• Turn on your monitor and then turn on your PC.
Q2: What is the recommended refresh rate for LCD monitor?
Ans.: Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance on screen, you can set it up to 75Hz to see if that removes the disturbance.
Q3: What are the .inf and .icm files on the
CD-ROM? How do I install the drivers
(.inf and .icm)?
Ans.: These are the driver files for your monitor. Follow the instructions in your user manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the ( companion
CD-ROM) included in this package.
35
8. Troubleshooting & FAQs
Monitor drivers (.inf and .icm files) will be installed automatically.
Q4: How do I adjust the resolution?
Ans.: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows ® Control
Panel with the "Display properties".
Q5: What if I get lost when I am making monitor adjustments via OSD?
Ans.: Simply press the OK button, then select
'Reset' to recall all of the original factory settings.
Q6: Is the LCD screen resistant to scratches?
Ans.: In general it is recommended that the panel surface is not subjected to excessive shocks and is protected from sharp or blunt objects. When handling the monitor, make sure that there is no pressure or force applied to the panel surface side.
This may affect your warranty conditions.
Q7: How should I clean the LCD surface?
Ans.: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.
Q8: Can I change the color setting of my monitor?
Ans.: Yes, you can change your color setting through OSD control as the following procedures,
• Press "OK" to show the OSD (On Screen
Display) menu
• Press "Down Arrow" to select the option
"Color" then press "OK" to enter color setting, there are three settings as below.
1. Color Temperature; With settings in the
6500K range the panel appears "warm, with a red-white color tone", while a
9300K temperature yields "cool, bluewhite toning".
2. sRGB; this is a standard setting for ensuring correct exchange of colors between different device (e.g. digital cameras, monitors, printers, scanners, etc)
3. User Define; the user can choose his/ her preference color setting by adjusting red, green blue color.
Note
A measurement of the color of light radiated by an object while it is being heated. This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.
Q9: Can I connect my LCD monitor to any
PC, workstation or Mac?
Ans.: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and workstations. You may need a cable adapter to connect the monitor to your
Mac system. Please contact your Philips sales representative for more information.
Q10: Are Philips LCD monitors Plug-and-
Play?
Ans.: Yes, the monitors are Plug-and-Play compatible with Windows 8/7/Vista/XP/
NT, Mac OSX, Linux
Q11: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD panels?
Ans.: Uninterrupted display of still or static images over an extended period may cause "burn in", also known as "afterimaging" or "ghost imaging", on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-known phenomenon in
LCD panel technology. In most cases, the
"burned in" or "atter-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.
36
8. Troubleshooting & FAQs
Always activate a moving screen saver program when you leave your monitor unattended.
Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content.
Warning
Severe"burn-in" or "after-image" or "ghost image" symptoms will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty.
Q12: Why is my Display not showing sharp text, and is displaying jagged characters?
Ans.: Your LCD monitor works best at its native resolution of 1920x1080@60Hz.
For best display, please use this resolution.
8.4 MHL FAQs
Q1: I cannot see my mobile device image on the monitor screen
Ans.:
• Please check if your mobile device is MHL certified.
• You also need to have a MHL certified cable to connect the devices.
• Make sure that you have connected to the
MHL-HDMI port, and that correct input is selected on the Monitor via the input selector (front bezel or OSD)
• The product is officially MHL-certified.
As this monitor is a passive display, if you encounter any unexpected troubles when using the MHL input, please refer to the mobile device’s user manual or contact the manufacturer of the mobile device.
Attention
No video input(MHL-HDMI)
• Make sure your mobile device has not entered standby (sleep) mode. If it has, then you will see a notification message on the display. Once the mobile device wakes up, the monitor’s display will wake and show the images. You may need to make sure that the correct input is selected if in between you have used or connected any other device
Q2. Why is the image on the monitor display of poor quality? My mobile device looks far better.
Ans.:
• The MHL standard defines fixed
1080p@30hz for output, and input. This monitor complies with this standard.
• The image quality depends on the quality of the original contents. If the content is of high resolution (example HD or 1080p), then it will appear in HD or 1080p on this monitor display. If the original content is in low resolution (example QVGA) it may look good on the mobile device due to its small screen size, but will look to be of lower quality on the large screen monitor display.
Q3. I cannot hear sound from the monitor display.
Ans.:
• Make sure your monitor display has builtin speakers and the volume is turned on the monitor side, and also on the mobile device side. You may also want to use optional headphones.
• If your monitor display does not have in built speakers, then you can connect optional headphones to the output on the monitor. Please ensure that the volume is turned on the monitor side, and also on the mobile device side.
For further information or FAQ, please visit official website of MHL org: http://www.mhlconsortium.org
37
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from
Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.
Version: M5274E1T
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Ultra-Narrow Bezel
- 27" (68.6 cm)
- AH-IPS
Related manuals
advertisement
Table of contents
- 3 1. Important
- 4 1.2 Notational Descriptions
- 5 material
- 6 2. Setting up the monitor
- 6 2.1 Installation
- 8 2.2 Operating the monitor
- 12 3. Image Optimization
- 12 3.1 SmartImage Lite
- 13 3.2 SmartContrast
- 13 3.3 Philips SmartControl Lite
- 19 4. Technical Specifications
- 23 4.1 Resolution & Preset Modes
- 24 5. Power Management
- 25 6. Regulatory Information
- 31 7. Customer care and warranty
- 31 Defect Policy
- 33 7.2 Customer Care & Warranty
- 36 8. Troubleshooting & FAQs
- 36 8.1 Troubleshooting
- 37 8.2 SmartControl Lite FAQs
- 38 8.3 General FAQs
- 40 8.4 MHL FAQs