advertisement
CONTENTS
Usage Notice .....................................................................................2
Using the Product .............................................................................9
Connection ......................................................................................17
EN-1
Usage Notice
Safety Instructions
Read all of these instructions before you operate your projector and save for future reference.
1. Read instructions
All the safety and operating instructions should be read before the appliance is operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp cloth for cleaning the projector housing. Do not use liquid or aerosol cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and optional parts) out of the reach of children as these bags may result in death by suffocation. Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust). Do not block or place anything near these slots, or internal heat build-up may occur, causing picture degradation or damage to the projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of your local power supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement parts are specified by the manufacture. Unauthorized substitutions may result in fire, electric shock or other hazards.
EN-2
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold location to a warm one. When the projector is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. To prevent the unit from possible damage, do not use the projector for at least 2 hours when there is an extreme or sudden change in temperature.
EN-3
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recommend using a video source device also equipped with a grounding type AC line plug to prevent signal interference due to voltage fluctuations.
Ground Ground
For Australia and
Mainland China
Ground
For Continental Europe
For the U.S.A. and Canada
Ground
For the U.K.
EN-4
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user
- friendly design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55" Texas Instruments DLP
®
technology (XGA model)
Single chip 0.65" Texas Instruments DLP ® technology (WXGA/1080P model)
XGA (1024 x 768 pixels)
WXGA (1280 x 800 pixels)
1080P (1920 x 1080 pixels)
Compatibility with Macintosh ® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
RS-232 connector for serial control
Quick Resume feature
Eco
+
mode for more economic usage
Full 3D
HDMI compatibility
PJLink TM compatibility
Support wireless dongle via internal power of VGA 2
LAN Settings allowing management of projector status from a remote computer
LAN display 4-1 (maximum 4PC/ NB display to 1 projector)
LAN display 1-M available (1PC/ NB can display to maximum 8 projectors at the same time)
USB display supports computer connection via USB B type to A type cable
Note
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.
EN-5
Package Contents
When you unpack the projector, make sure you have all these components:
Projector AC Power Cord VGA Cable (D-SUB to D-SUB)
Remote Control with
Laser Pointer & batteries
(AAA *2 PCS)
Carry Bag (optional for certain models)
Dust filter (depending on region)
Documentation:
5 User's Manual
5 Warranty Card
5 Quick Start Card
5 WEEE Card
(for EMEA only)
Note
For European warranty information please visit www.optomaeurope.com
Due to the difference in applications for each country, some regions may have different accessories.
Contact your dealer immediately if any items are missing, appear damaged, or if the
unit does not work.
Save the original shipping carton and packaging material; they will come in handy if you ever need to ship your unit. For maximum protection, repack your unit as it was originally packed at the factory.
EN-6
Projector Overview
Front View
10 9 8
3
4
1
2
5
Front adjustment foot
Projection lens
Focus ring
Front IR remote control sensor
Security bar
1 2 3 4 5 6 7
8
9
6
7
Speaker
Ventilation holes
Control panel
Zoom ring
10
Top cover
EN-7
Rear View
1 2 3 4 5 6 7 8
3
4
1
2
Optional air dust
AC power socket
Connection ports
Kensington lock
Bottom View
7
8
5
6
Rear IR remote control sensor
Optional wireless dongle slot
Speaker
Ventilation holes
1
2
1
Ceiling mount holes
Rear adjustment feet
Note
This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package.
Contact your dealer for information to mount the projector on a ceiling.
EN-8
Using the Product
Control Panel
1
2
3
4
11
10
9
8
1
5
6
7
1
2
3
4
5
6
7
8
9
10
11
Keystone ( / )
Manually correct distorted images resulting from an angled projection.
SOURCE
Switch between input signals.
HELP
Display Help menu.
MENU
Display or exit the on-screen display menus.
TEMP (Temp LED indicator)
Refer to “LED Indicator Messages” on
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages” on page 88
.
POWER (Power LED indicator)
Refer to “LED Indicator Messages” on
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
Re-SYNC
Automatically synchronize the projector to the input source.
Power
Turn the projector on or off.
ENTER
Confirm your item selection.
EN-9
Connection Ports
1 2 3 4 5 6 7 8 9
17 16 15 14 13 12 11 10
6
7
1
2
3
4
5
RS-232C
When operating the projector via a computer, connect this to the controlling computer's RS-232C port.
VGA-OUT
Connect to an external monitor.
In Eco mode (Standby), VGA-OUT is disabled.
In Active mode (Standby), VGA-OUT is enabled.
S-VIDEO
Connect S-Video output from video equipment to this jack.
MOUSE/SERVICE
This connector supports firmware update, remote mouse and page up/ down.
HDMI
Connect HDMI output from video equipment to this jack.
DVI-D
Connect DVI-D output from computer to this jack.
DISPLAY
USB display supports computer connection via USB B type to A type cable.
EN-10
8
9
RJ-45
For LAN display/network control and web server.
FLASH DRIVE
This connector supports USB flash drive display.
10
11
12
13
14
15
16
17
12V OUT
12V DC out
MIC
Microphone input jack.
AUDIO OUT
Connect to a speaker or other audio input equipment.
AUDIO-IN 1/AUDIO-IN 2
Connect an audio output from a computer to this jack.
AUDIO-IN 3 (L/R)
Connect an audio output from a video device to this jack.
VIDEO
Connect composite video output from video equipment to this jack.
VGA2-IN / YPbPr /
Connect image input signal (analog RGB or component) to this jack.
Support wireless dongle via internal power of VGA 2.
VGA1-IN / YPbPr
Connect image input signal (analog RGB or component) to this jack.
EN-11
Remote Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
2
3
5
6
4
Power
Turn the projector on or off.
Source
Switch between input signals.
Left mouse
Perform the left button of the mouse when mouse mode is activated.
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
"UP" key: When menu is off, up key for emulation of USB mouse.
"Left" key: When menu is off, left key for emulation of USB mouse.
"Right" key: When menu is off, right key for emulation of USB mouse.
"Down" key: When menu is off, down key for emulation of USB mouse.
Page-
Perform page down function when mouse mode is activated.
Keystone (+/-)
Manually correct distorted images resulting from an angled projection.
EN-12
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Brightness
Display the setting bar for adjustment of brightness.
Freeze
Freeze the projected image.
HDMI
Display HDMI signal.
(This function will not work if product does not have HDMI.)
S-Video
Display S-Video signal.
Eco+
Brightness mode menu on/off.
VGA
Switch input source to VGA1 or VGA2 by sequence.
Switch
Switch to mouse mode when the on-screen menus are close.
User
User definable key for customized function.
Re-SYNC
Automatically synchronize the projector to the input source.
Right mouse
Perform the right button of the mouse when mouse mode is activated.
Enter
Confirmed selections.
Enter key for emulation of USB mouse via USB.
Laser
Aim the remote at the viewing screen, press and hold this button to activate the laser pointer.
Page+
Perform page up function when mouse mode is activated.
Volume (+/-)
Adjust the volume level.
Menu
Display on-screen display menus.
Zoom
Magnifies or reduces the projected picture size.
AV mute
Momentarily turns off/on the audio and video.
Video
Display video signal.
3D
Turn on or off 3D function.
USB
EN-13
Switch to mouse mode when the on-screen menus are close.
27
Numbered keypad
Press 0 to 9 to enter a password when required.
Note
Remote Control (IR) or Remote Control with Laser Pointer (depending on region). See
Appendix for the Remote with Laser Pointer.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See
“Connecting a computer” on page 19
for details.
2. Set the input signal to VGA1 or VGA2.
3. Press USB or Switch on the remote control to switch to mouse mode when the on-screen menus are close. An icon appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
To move the cursor on the screen, press / / / .
To left-click, press L.
To right-click, press R.
To return to the normal mode, press Switch again.
Note
HDMI also supports mouse function.
EN-14
Installing the Batteries
1. Open the battery cover in the direction shown.
2. Install batteries as indicated by the diagram inside the compartment.
3. Close the battery cover into position.
Caution
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
Keep the batteries out of the reach of children. There is a danger of death by accidentally swallowing the batteries.
Remove batteries from remote control when not using for extended periods.
Do not dispose of the used batteries along with household waste. Dispose of used batteries according to local regulations.
Danger of explosion may happen if batteries are incorrectly replaced. Replce all the batteries with new ones.
Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry place.
If suspect battery leakage, wipe out the leakage and then replace new batteries. If the leakage adheres to your body or clothes, rinse well with water immediately.
EN-15
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
Operating the projector from the front
15 15
5m
10m
7m
Operating the projector from the rear
15 15
5m
10m
7m
Note
The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
EN-16
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
1 2 3 4 1 5
6 7 8
9 10
11
3
12
1. ................................................................... VGA cable (D-Sub to D-Sub)
2. .................................................................. *USB cable (B type to A type)
3. .........................................................................................*Audio cable
4. .........................................................................................*DVI-D cable
5. ................................................................................*VGA to DVI-A cable
6. ....................................................... *VGA (D-Sub) to HDTV (RCA) cable
7. .........................................................................................*S-Video cable
8. .........................................................................................*HDMI cable
9. ......................................................................................*Audio L/R cable
EN-17
10. .......................................................................... *Composite video cable
11. .......................................................................................*USB flash drive
12. .............................................................. *Microphone 3.5 mini jack cable
Note
Due to the difference in applications for each country, some regions may have different accessories.
(*) Optional Accessory
EN-18
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both IBM ® compatible and Macintosh ® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.
2. Connect the other end of the VGA cable to the VGA1/YPbPr or VGA2/
YPbPr signal input socket on the projector.
Important
Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.
EN-19
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the VGA-OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in “Connecting a computer” on page 19 .
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to
DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the VGA-OUT socket on the projector.
VGA-OUT loop through:
During working mode:
1. If VGA1 is projecting out, VGA-OUT source will be VGA1.
2. If VGA2 is projecting out, VGA-OUT source will be VGA2.
3. If VGA1 and VGA2 are all have sources, default VGA-OUT is VGA1.
4. If none of VGA1 and VGA2 is projecting out, VGA-OUT is disabled.
During Standby
1. VGA-OUT will keep the latest display VGA source signal. Default VGA-
OUT is VGA1.
2. If the projector is in Power Mode (Standby) < 0.5W, VGA-OUT is disabled.
EN-20
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the following output sockets:
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:
Terminal name Terminal appearance
HDMI HDMI
Component
Video
S-Video
Video
VGA1/YPbPr or
VGA2/YPbPr
S-VIDEO
VIDEO
Reference
“Connecting an
HDMI source device” on page 22
Component Video source device” on page 22
S-Video source device” on page 23
“Connecting a composite Video source device” on page 23
Picture quality
Best
Better
Good
Normal
EN-21
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused
HDMI output jacks available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the
HDMI source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused
Component Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the
Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the
VGA1/YPbPr or VGA2/YPbPr socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
EN-22
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See
“Connecting Video source devices” on page 21 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if
Component Video and S-Video inputs are unavailable for use. See
“Connecting Video source devices” on page 21 for details.
EN-23
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Connect the AC power cord and relevant peripheral signal cable(s) to the projector.
2. Press to turn on the projector.
The projector takes a minute or so to warm up.
3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
If you are connecting multiple sources to the projector simultaneously, press SOURCE on the projector or Source on the remote control to select your desired signal or press your desired signal key on the remote control.
Warning
Never look into the lens when the lamp is on. This can damage your eyes.
This focal point concentrates high temperature. Do not place any object near it to avoid possible fire hazard.
Powering Off the Projector:
1. Press to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
2. Press again to confirm.
The cooling fans continue to operate for cooling cycle.
When the Power LED becomes steady red, the projector has entered stand-by mode.
If you want to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered stand-by mode. Once in stand-by mode, simply press to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
Warning
When Quick Resume is on, if turning off the projector accidentally and Quick
Resume selected within a period of 100 seconds, the projector will instantly power on again.
When Quick Resume is off, if turning off the projector, users need to wait until the cooling process is finished and then restart the projector. It will take a few minutes because the fan will keep running until the internal temperature is reduced to certain level.
EN-24
Adjusting the Projector Height
Adjustment feet
The projector is equipped with three adjustment feet to adjust the image height.
1. To raise or lower the image, turn the front adjustment foot.
2. To level the image on the screen, turn the rear adjustment feet to finetune the height.
Note
To avoid damaging the projector, make sure that the adjustment feet are fully retracted before placing the projector in its carrying case.
Adjusting the Projector Zoom and
Focus
Zoom ring
Focus ring
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image size by rotating the zoom ring.
EN-25
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Maximum zoom Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
XGA model
Screen size
Diagonal
[inch (cm)]
30 (76)
40 (102)
60 (152)
80 (203)
100 (254)
120 (305)
150 (381)
200 (508)
250 (635)
300 (762)
WXGA model
Screen size
Diagonal
[inch (cm)]
30 (76)
40 (102)
60 (152)
80 (203)
100 (254)
120 (305)
150 (381)
200 (508)
250 (635)
300 (762)
4 : 3 Screen
Projection distance [feet (m)]
(min. zoom) (max. zoom)
Image height
[inch (cm)]
2.7 (0.85)
3.7 (1.1)
5.6 (1.7)
4.5 (1.4)
5.9 (1.8)
8.9 (2.7)
18 (46)
24 (61)
36 (91)
7.4 (2.3)
9.3 (2.8)
11.2 (3.4)
13.9 (4.3)
18.6 (5.7)
23.2 (7.1)
27.9 (8.5)
11.9 (3.6)
14.8 (4.5)
17.8 (5.4)
22.3 (6.8)
29.7 (9.1)
37.2 (11.3)
44.6 (13.6)
48 (122)
60 (152)
72 (183)
90 (229)
120 (305)
150 (381)
180 (457)
Vertical offset
[inch (cm)]
2.7 (7)
3.6 (9)
5.4 (14)
7.2 (18)
9.0 (23)
10.8 (27)
13.5 (34)
18.0 (46)
22.5 (57)
27.0 (69)
16:10 Screen
Projection distance [feet (m)]
(min. zoom)
3.0 (0.9)
(max. zoom)
4.6 (1.4)
Image height
[inch (cm)]
16 (40)
4.0 (1.2)
6.0 (1.8)
8.0 (2.4)
6.0 (1.8)
9.0 (2.7)
12.0 (3.7
21 (54)
32 (81)
42 (108)
10.0 (3.1)
12.0 (3.7)
15.0 (4.6)
20.0 (6.1)
25.0 (7.6)
30.0 (9.2)
15.0 (4.6)
18.0 (5.5)
22.5 (6.9)
30.0 (9.2)
37.5 (11.4)
45.0 (13.7)
53 (135)
64 (162)
79 (202)
106 (269)
132 (336)
159 (404)
Vertical offset
[inch (cm)]
2.4 (6)
3.2 (8)
4.8 (12)
6.4 (16)
7.9 (20)
9.5 (24)
11.9 (30)
15.9 (40)
19.9 (50)
23.8 (61)
EN-26
1080P model
Screen size
Diagonal
[inch (cm)]
30 (76)
40 (102)
60 (152)
80 (203)
100 (254)
120 (305)
150 (381)
200 (508)
250 (635)
300 (762)
3.0 (0.9)
16:9 Screen
Projection distance [feet (m)]
(min. zoom) (max. zoom)
4.6 (1.4)
Image height
[inch (cm)]
15 (37)
4.0 (1.2)
6.0 (1.8)
8.0 (2.4)
10.0 (3.1)
12.0 (3.7)
6.0 (1.8)
9.0 (2.7)
12.0 (3.7
15.0 (4.6)
18.0 (5.5)
20 (50)
29 (75)
39 (100)
49 (125)
59 (149)
15.0 (4.6)
20.0 (6.1
25.0 (7.6)
30.0 (9.2)
22.5 (6.9)
30.0 (9.2)
37.5 (11.4)
45.0 (13.7)
74 (187)
98 (249)
123 (311)
147 (374)
Vertical offset
[inch (cm)]
2.2 (6)
2.9 (7)
4.4 (11)
5.9 (15)
7.4 (19)
8.8 (22)
11 (28)
14.7 (37)
18.4 (47)
22.1 (56)
Note
Position the projector in a horizontal position; other positions can cause heat buildup and damage to the projector.
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may build-up on critical parts and damage the projector or its performance.
Consult with your dealer for special installation such as suspending from a ceiling.
EN-27
Adjusting the position using the vertical lens shift function
If the projector is not positioned right in front of the center of the screen, you can adjust the vertical position of projected image by moving the vertical lens ring within the shift range of the lens.
1. Lens shift adjustment for XGA
The display position can be shifted upward up to 6.5% elevation of the display. (When turn the vertical lens shift ring to the right (left), the display moves up (down)).
Lens shift adjustable range
6.5%
Shift to top
0.065V
1V
0.15V
Shift range
Lens shift center position
2. Lens shift adjustment for WXGA
The display position can be shifted upward up to 14.5% elevation of the display. (When turn the vertical lens shift ring to the right (left), the display moves up (down)).
Shift to top
0.145V
1V
0.12V
Lens shift adjustable range
14.5%
Shift range
Lens shift center position
EN-28
3. Lens shift adjustment for 1080P
The display position can be shifted upward up to 17% elevation of the display. (When turn the vertical lens shift ring to the right (left), the display moves up (down)).
Shift to top
0.17V
1V
0.15V
Lens shift adjustable range
17%
Lens shift center position
Shift range
Attention
Please note the following s when using the projector.
Do not touch the lens while it is moving as this could cause injury to the fingers.
Never allow children to touch the lens.
EN-29
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2. When OSD is displayed, use / key to select to select any item in the main menu. While making a selection on a particular page, press or
“Enter key to enter sub menu.
3. Use / key to select the desired item and press / /”Enter” key to enter the Single-Item-Menu.
4. Use the / key to adjust the value. Use “Enter” to confirm the selection.
5. Select the next item to be adjusted in the sub menu and adjust as described above.
6. Press ”Menu” to go back to Sub-Menu.
7. To exit, press “Menu” again. The OSD menu will close and the projector will automatically save the new settings.
Main Menu
Sub-Menu Settings
Single-Item-
Menu
EN-30
Menu tree
Main Menu
IMAGE
Sub-Menu
Display Mode
Brightness
Contrast
Sharpness
Color
Tint
Advanced
Single-Item
Menu
Presentation /
Bright / Movie / sRGB /
Blackboard /
DICOM SIM /
User / 3D
Gamma
BrilliantColor™
Color Temp.
Color Settings
Red
Green
Blue
Cyan
Magenta
Yellow
White
Reset
Exit
Color Space
1.8 / 2.0 / 2.2 /
2.6 / Film /Video
/ Graphic
Warm / Medium
/ Cold
Hue / Saturation
/ Gain
Hue / Saturation
/ Gain
Hue / Saturation
/ Gain
Hue / Saturation
/ Gain
Hue / Saturation
/ Gain
Hue / Saturation
/ Gain
Red / Green /
Blue
Auto / RGB
(0~255) / RGB
(16~235) YUV
EN-31
IMAGE
DISPLAY
Advanced
Reset
Format
Signal
Exit
Edge Mask
Zoom
Image Shift
V Keystone
Auto Keystone
H
V
3D
3D Mode
3D--->2D
3D Format
3D Sync Invert
Automatic
Phase (VGA)
Frequency
(VGA)
H. Position
(VGA)
V. Position
(VGA)
Exit
On / Off
Yes / No
XGA:
4:3 / 16:9 /
Native / Auto
WXGA/1080P:
4:3 / 16:9 or
16:10 / LBX /
Native / Auto
On / Off
DLP-Link / IR
3D / L / R
Auto / SBS / Top and Bottom /
Frame
Sequential
On / Off
Language
SETUP
Projection
Menu Location
Screen Type
16: 10/16:9
(WXGA)
EN-32
SETUP
Security
Projector ID
Audio Settings
Advanced
Network
Security
Security Timer
Change Password
Exit
Internal Speaker
Mute
Volume
Audio
Mic
Audio Input
On / Off
Month / Day /
Hour
On / Off
On / Off
Logo
Logo Capture
Closed Captioning
Exit
LAN Settings
WLAN Settings
Control Settings
Default / Audio
1 / Audio 2 /
Audio 3
Default / Neutral
/ User
Off / CC1 / CC2
Network Status
Connected /
Disconnected
MAC Address
DHCP
IP Address
Subnet Mask
Gateway
DNS
Exit
WLAN
On / Off
Network Status
On / Off
Connected /
Disconnected
MAC Address
IP Address
SSID
Connection
Mode
Exit
Crestron
Extron
PJ Link
AMX Device
Discovery
Telnet
HTTP
Exit
Infrastructure /
Access Point
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
EN-33
Input Source
Source Lock
High Altitude
Information Hide
Keypad Lock
Test Pattern
12V Trigger
IR Function
Background Color
OPTIONS
Remote Settings
Advanced
Lamp Settings
Optional Filter
Settings
Direct Power On
Signal Power On
Auto Power Off
(min.)
Sleep Timer (min.)
Quick Resume
Power Mode
(Standby)
Lamp Hour
Lamp Reminder
Brightness Mode
Lamp Reset
Exit
Optional Filter
Installed
Filter Usage Hours
Filter Reminder
Filter Reset
Exit
Reset
EN-34
VGA1 / VGA2 /
Video / S-video /
HDMI / DVI /
Flash drive/
Network display/ USB display
On / Off
On / Off
On / Off
On / Off
None / Grid /
White
On / Off / Auto
3D
On / Front /
Back / Off
Black / Red /
Blue / Green /
White
Display Mode /
Format / 3D
Sync Invert /
Mute / Test
Pattern / DVI /
VGA2 / Network
Display
On / Off
On / Off
On / Off
Active / Eco
On / Off
Bright /
Dynamic / Eco
+
Yes / No
Yes / No
Off / 300hr /
500hr / 800hr /
1000hr
Yes / No
Yes / No
IMAGE
Display Mode
There are many factory presets optimized for various types of images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Moive: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum color settings when projecting onto a blackboard (green).
User: User’s settings.
DICOM SIM:
Recommended for DICOM format files in simulation mode.
3D: Recommended setting for 3D mode. Any further adjustments by the user in 3D will be saved in this mode for further use.
Note
DCIM SIM option is only for training or reference. It not used for actual diagnosis.
DICOM represents for the Digital Imaging and Communications in Medicine. This is a standard created by the American College of Radiology and the National Electrical
Manufacturers Association. This standard specifies the method of digital image data to be transferred from one system to another.
Brightness
Brighten or darken the image.
Contrast
EN-35
Set the difference between light and dark areas.
Sharpness
Sharpen or soften the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Shift colors toward red or green.
Note
“Color” and “Tint” functions are only supported under Video mode.
Advanced
Gamma
This allows you to choose a degamma table that has been fine-tuned to bring out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
2.2: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing true, more vibrant colors in picture. The range is from “1” to “10”. If you prefer a stronger enhanced image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting.
EN-36
Color Temp.
If set to cold temperature, the image looks more blue. (cold image)
If set to medium temperature, the image maintains normal colorings for white.
If set to warm temperature, the image looks more red. (warm image)
Color Settings
Press / /“Enter” key to enter the next menu as below and then use / /
/ key to select color. Press “Enter” to finalize the selection.
Red/Green/Blue/Cyan/Magenta/Yellow/White: Use / to toggle Hue/
Saturation/Gain and then use / to adjust the value.
Reset: Choose “Yes” to return the factory default settings for color adjustments.
Color Space
Select an appropriate color matrix type from AUTO, RGB, RGB (0-255)(*),
RGB (16-235)(*) or YUV.
Note
(*) for HDMI only.
Signal
Automatic: Automatically selects the singal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again.
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it.
Frequency: Change the display data frequency to match the frequency of your computer’s graphic card. Use this function only if the image appears to flicker vertically.
H. Position: Adjust the image left or right within the projection area.
V. Position: Adjust the image up or down within the projection area.
EN-37
Reset
Return the display parameters on IMAGE menu to the factory default settings.
EN-38
DISPLAY
Format
Use this function to choose your desired aspect ratio.
For XGA model:
Source
4:3
16:9
Native
480i/p
1024x768 center
576i/p 1080i/p
1024x576 center
Displays the original image without any scaling.
Auto (Default) If source is 4:3, auto resize to 1024 x 768.
If source is 16:9 auto resize to 1024 x 576.
If source is 15:9 auto resize to 1024 x 614.
If source is 16:10 auto resize to 1024 x 640.
For WXGA model:
16:9 or 16:10 depend on “Screen Type” setting.
16:10 Screen
720p
16 : 10 screen
4:3
16:10
LBX
480i/p 576i/p
1066 x800 center
1280x800 center
1080i/p 720p PC
1280x960 center, then get the central 1280x800 image to display.
Native 1:1 mapping centered
1:1 mapping display 1280 x
800
1280x720
Centered
1:1 mapping centred
Auto (Default) Input source will be fit into 1280x800 display area and be kept its original aspect ratio.
If source is 4:3, auto resize to 1066 x 800.
If source is 16:9 auto resize to 1280 x 720.
If source is 15:9 auto resize to 1280 x 768.
If source is 16:10 auto resize to 1280 x 800.
EN-39
16:9 Screen
16 : 9 screen 480i/p 576i/p
4:3 960x720 center
16:9
LBX
1280x720 center
1080i/p 720p PC
1280x960 center, then get the central 1280x720 image to display.
Native 1:1 mapping centered
1:1 mapping display 1280 x
720
1280x720
Centered
1:1 mapping centred
Auto (Default) If this format is select, Screen type will auto become 16:9 (1280 x
720).
If source is 4:3, auto resize to 960 x 720.
If source is 16:9 auto resize to 1280 x 720.
If source is 15:9 auto resize to 1200 x 720.
If source is 16:10 auto resize to 1152 x 720.
For 1080P model:
16 : 9 screen 480i/p 576i/p
4:3 1440x1080 center
1080i/p 720p PC
16:9
LBX
1920x1080 center
1920x1440 center, then get the central 1920x1080 image to display.
Native 1:1 mapping centered
Auto (Default) If this format is select, Screen type will auto become 16:9 (1920 x
1080).
If source is 4:3, auto resize to 1440 x 1080.
If source is 16:9 auto resize to 1920 x 1080.
If source is 16:10 auto resize to 1920 x 1200 and cut 1920 x 1080 area to display.
Edge Mask
Edge Mask function removes the noise in a video image. Overscan the image to remove video encoding noise on the edge of video source.
Note
Each I/O has different setting of “Edge Mask”.
“Edge Mask” and “Zoom” can’t work at same time.
Zoom
Zoom in and out the images.
Image Shift
Shift the projected image position horizontally and vertically.
V Keystone
Adjust image distortion vertically. If the image looks trapezoidal, this option can help make the image rectangular.
Note
EN-40
Keystone adjustment might affect the complete presentation of the OSD menu.
When adjusting the V Keystone, Auto Keystone will be set at "Off" automatically.
Auto Keystone
Automatically correct distorted images resulting from an angled projection.
3D
3D Mode
DLP Link: Select “DLP Link” to use optimized settings for DLP Link 3D glasses.
IR: Select “IR” to use optimized settings for IR-based 3D glasses.
3D--->2D
3D: Select 3D format.
L: Select left eye data.
R: Select right eye data.
3D Format
SBS: Use this mode for “Side-by-side” format 3D content.
Top and Bottom: Use this mode for “Top and Bottom” format 3D content.
Frame Sequential: Use this mode for “Frame Sequential” format 3D content.
3D Sync. Invert
Press the “On” to invert left and right frame contents.
Press the “Off” for default frame contents.
EN-41
SETUP
Language
Select the language used by the on-screen menu. Press / /“Enter” key to enter the sub menu and then use the / / / key to select your preferred language. Press “Enter” to finalize the selection.
Projection
Adjust the picture to match the orientation of the projector: upright or upsidedown, in front of or behind the screen. Invert or reverse the image accordingly.
Menu Location
Choose the menu location on the display screen.
Screen Type (for WXGA model only)
Choose the screen type from16:10 or 16:9.
Security
Security
On: Choose “On” to use security verification when the turning on the projector.
Off: Choose “Off” to be able to switch on the projector without password verification.
EN-42
Security Timer
Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has elapsed you will be requested to enter your password again.
Change Password
First time:
1. Press “Enter” to set the password.
2. The password has to be 4 digits.
3. Use number button on the remote to enter your new password and then press “Enter” key to confirm your password.
Change Password:
1. Press “Enter” to input old password.
2. Use number button to enter current password and then press
“Enter” to confirm.
3. Enter new password (4 digits in length) using the number buttons on the remote, then press “Enter” to confirm.
4. Enter new password again and press “Enter” to confirm.
If the incorrect password is entered 3 times, the projector will automatically shut down.
If you have forgotten your password, please contact your local office for support.
Note
Password default value is “1234” (first time).
Projector ID
ID definition can be set up by menu (range 0~99), and allow user control an individual projector by RS232.
Audio Settings
Internal Speaker
Use the internal speaker of projector.
Mute
Cut off the sound temporarily.
Volume
Adjust the volume level for Audio or Mic input source.
EN-43
Audio Input
Select audio input sources.
Advanced
Logo
Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on.
Default: The default startup screen.
Neutral: Neutral startup screen.
User: "User" is the screen that you captured.
Logo Capture
Capture the current projection screen as a start up screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on.
Off: select “Off” to turn off the closed captioning feature.
CC1:CC1 language: American English.
CC2:CC2 language (depending on the TV channel of the user):Spanish,
French, Portuguese, German, Danish.
Network
LAN Settings
Allow you to configure the wired LAN settings.
Network Status: Display the network connection status.
MAC Address: a read-only display of MAC Address.
DHCP: This protocol automatically assigns IP Addresses to networked devices.
On: Assign an IP address to the projector from an external DHCP server automatically.
Off: Assign an IP address manually.
IP Address: Select an IP address.
Subnet mask: Select subnet mask number.
Gateway: Select the default gateway of the network connected to the projector.
DNS: Select DNS number.
WLAN Settings
Allow you to configure the wireless LAN settings.
WLAN: Turn on or off wireless LAN function.
Network Status: Display the network connection status.
EN-44
MAC Address: a read-only display of MAC Address.
IP Address: a read-only display of IP Address.
SSID: Display the projector’s SSID information.
Connection Mode: Methods for connecting to wireless networks with Wi-
Fi enabled devices.
Control Settings
Allow you to configure nework settings.
Crestron: Turn on or off Crestron. *Note: Port 41794
Extron: Turn on or off Extron. *Note: Port 2023
PJ Link: Turn on or off PJ Link. *Note: Port 4352
AMX Device Discovery: Turn on or off AMX Device Discovery. *Note:
Port 9131
Telnet: Turn on or off Telnet. *Note: Port 23
HTTP: Turn on or off HTTP. *Note: Port 80
EN-45
OPTIONS
Input Source
Use this option to enable / disable input sources. Press / /“Enter” key to enter the sub menu and select which sources you require. Press “Enter” to finalize the selection. The projector will not search for inputs that are not selected.
Source Lock
On: The projector will only search current input connection.
Off: The projector will search for other signals if the current input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Information Hide
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
EN-46
Keypad Lock
When the keypad lock function is “On”, the control panel will be locked however, the projector can be operated by the remote control. By selecting “Off”, you will be able to reuse the control panel.
Note
To turn off the keypad lock, press and hold “Enter” key on top of the projector for 5 seconds.
Test Pattern
Display a test pattern. There are Grid, White pattern and None.
12V Trigger
Choose the setting from On / Off to Auto 3D to set 12V Trigger.
IR Function
Choose the setting from On / Front / Back to Off and then choose "Yes" to apply the selection.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or “White”, screen when no signal is available.
Remote Settings
Allow user to define a short cut key on the remote control, and the function item is selected in OSD menu.
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without pressing the “ ” key on the projector control panel or on the remote control.
Signal Power On
If Signal Power On is activated, the projector will turn on automatically when
VGA signal is detected.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes).
EN-47
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, with or without a signal being sent to the projector. The projector will automatically power off when the countdown has finished (in minutes).
Quick Resume
If the projector is accidentally turned off, this feature allows the projector to be instantly powered on again within 100 seconds of power down.
Power Mode (Standby)
Set whether the VGA-OUT function works when the projector is in standby
(powered off but connected to AC power).
Eco: The VGA-OUT and AUDIO-OUT functions will not work when the projector is in standby.
Active: The VGA-OUT and AUDIO-OUT functions will work when the projector is in standby.
Note
When Power mode (Standby) is set to Eco (<0.5W), the VGA output, Signal Power On,
Audio pass-through will be deactivated when the projector is in standby.
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message when the changing lamp message is displayed.
Brightness Mode
Bright: Choose “Bright” to increase the brightness.
Dynamic: Choose “Dynamic“ to dim the lamp power which will be based on brightness level of the content and adjust lamp power consumption between 100% and 30% dynamically. The lamp life will be extended.
Eco+: Choose “Eco+” to dim the lamp power which will be based on brightness level of the content and adjust lamp power consumption between 80% and 30% dynamically. The lamp life will be extended.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
Optional Filter Settings
Optional Filter Installed
Choose “Yes” if an optional dust filter is installed.
Filter Usage Hours
Display the dust filter’s elapsed operating time (in hours).
EN-48
Filter Reminder
Sets a filter reminder if timer is up.
Filter Reset
Reset the dust filter hour counter after replacing the dust filter.
Reset
Choose “Yes” to return the display parameters on all menus to the factory default settings.
EN-49
Controlling the projector through a
LAN environment
You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network.
Wired connection
Internet
IP Router
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.
2. Press “Menu” and then go to SETUP > Network menu.
3. Highlight LAN Settings and press “Enter”.
4. Make sure the Network Status shows Connected.
5. Press DHCP and press / to select On.
6. Please wait for around 15 - 20 seconds, and then re-enter the Wired
LAN page. The IP Address, Subnet Mask, Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.
Important
If the Projector IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Gateway, and DNS information when the projector is on.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press to highlight DHCP and press / to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet
Mask, Gateway, and DNS settings.
4. Press to select the item you want to modify and press “Enter”.
EN-50
5. Press / to move the cursor and enter the value.
6. When you press “Menu”, a confirm message will pop-up to ask you if you want to save the settings.
Important
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Gateway, and DNS information when the projector is on.
EN-51
Wireless connection
Optoma wireless dongle
To connect to the projector wirelessly, you have to plug an Optoma wireless dongle (optional) to the USB Type A connector on the side of the projector, and then only a few OSD configuration steps are required.
1. Make sure the projector is turned on.
2. Press “Menu” and then go to SETUP > Network menu.
3. Highlight WLAN and press “Enter”.
4. Make sure the Network Status shows Connected.
5. Make sure the SSID information is displayed.
6. In AP mode, you need to use your computer’s wireless connection utility to search the projector’s SSID and connect to it. Then you can search the projector with Optoma Presenter. To use Infrastructure mode, you should connect both your computer and projector to the same AP router and make connections with the IP address.
EN-52
About AP and Infrastructure modes
In AP mode, you need to use your computer's wireless connection utility to search for the projector's SSID and connect to it. Then you can search for the projector with Optoma Presenter.
In Infrastructure mode, you should connect both your computer and projector to the same AP router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Infrastructure modes.
(AP Mode) (Infrastructure Mode)
Internet
Internet
Important
If you need more information about AP and Infrastructure modes, please refer to user documentations for Wireless Routers which are usually available on 3C stores.
EN-53
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector.
Important
Make sure your browser supports IE7, IE8, IE9, Saferi 5.1.2, Google Chrome 18,
Firefox 10.0.1.
The screenshots in this manual are for reference only, and may differ from the actual design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Optoma webpage control system appears.
3
5
6
4
3. To change the language for the web pages, click the down arrow to reveal a drop down list and select a desired language.
4. To download Optoma Presenter, click Download. See "Displaying images through vsPresenter" on page 40 for details.
5. The Crestron (eControl) page displays the Crestron eControl user interface. See “About Crestron control” on page 56 for details.
EN-54
6. To have access to the Admin page, you need to enter a password. The default password is “admin”.
System Status: Displays the system information.
General Setup: Allows you to turn on/off the projector, switch the input signal for the projector, and change the password for the
Administrator page.
Projector Control: Provides some OSD menu items for adjusting the projected pictures. See "Menu Operation" on page 23 for details.
Alert Setup: Allows you to setup the mail server and send system error messages to your ITS administrator.
Network Setup: Provides wired and wireless network settings.
Reset to Default: Allows you to restore the device to the factory default settings.
Reboot System: Allows you to restart the network.
EN-55
About Crestron control
1. The Crestron (eControl) page displays the Crestron eControl user interface. The eControl page provides a variety of virtual keys to control the projector or adjust the projected pictures.
i ii i
You can press
W/X to reveal more buttons.
i i.
These buttons function the same as the ones on the OSD menus or remote control.
ii. To switch between input signals, click on your desired signal.
Important
The Menu button can also be used to go back to previous OSD menus, exit and save menu settings.
The source list varies according to the connectors available on the projector.
When you use the projector control panel or remote control to change the OSD menu settings, it may take a while for the web browser to synchronize these changes with the projector.
EN-56
2. The tools page allows you to manage the projector, configure the LAN control settings and secure access of remote network operation on this projector.
i ii
v iii iv i.
This section is only used with the Crestron Control System. Please contact Creston or refer to its user manual for setup information.
ii. This area is used for naming the projector, associating it with a particular location, assigning a responsible party to it, and adjusting network settings.
iii. This area is used to set User and Admin passwords. When password protection is enabled, unauthorized changes to the projector configuration will be avoided.
Important
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the projector.
iv. Press Exit to go back to the remote network operation page.
EN-57
Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow:
Category Item Input Length
Crestron Control
Projector
Network Configuration
User Password
Admin Password
IP Address
IP ID
Port
Projector Name
Location
Assigned To
DHCP (Enabled)
IP Address
Subnet Mask
Default Gateway
DNS Server
Enabled
New Password
Confirm
Enabled
New Password
Confirm
Maximum Number of
Characters
15
2
5
10
9
9
(N/A)
15
15
15
15
(N/A)
20
2
(N/A)
20
20
EN-58
3. The info page displays the information and status of this projector.
Press exit to go back to the Crestron remote network operation page.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView software administrators/users who connect to the same local area network.
Important
Please only deliver the messages in English letters and digits.
For more information, visit http://www.crestron.com
& www.crestron.com/getroomview .
EN-59
**Crestron RoomView
On the "Edit Room" page, enter the IP Address (or hostname) as shown on the projector's on-screen display (OSD) menu, and "05" for IPID, "41794" for the reserved Crestron control port.
About Crestron RoomView setting and command method, please access below website to get RoomView User Guide and more information: http://www.crestron.com/features/ roomview_connected_embedded_projectors_devices/resources.asp
EN-60
Displaying images through Optoma
Presenter
Downloading and installing Optoma Presenter
The Optoma Presenter is an application running on the host PC. It helps connect your computer to an available network projector and transfer the desktop content to the network projector via local network connection.
1. Enter the main page of Network Control. See steps 1-2 on page 54 for details.
2. Download Optoma Presenter.
3. When the download is complete, install the software to your computer by clicking the exe file. Follow the on-screen instructions to complete the installation.
4. Launch Optoma Presenter.
Using Optoma Presenter
1
2
4
3
1. The Search page allows you to search and connect to a projector.
EN-61
i.
To search for projectors, simply click Search to list all the projectors on the same local area network. Click the desired projectors in the
Search result list, and click Connect. You can also type a desired projector name and click Search. ii. You can also type the projector IP address and click Connect to connect the projector directly.
2. You can choose a capture mode and display location from here.
i.
To display a full screen, click FullScreen.
ii. If you wish to change the square, click Alterable.
iii. If there are multiple computers connected to the projector, you can decide a display zone by clicking All, L, R, 1, 2, 3 or 4.
3. You can manage the connected projectors listed under Device
Management.
Under a conference mode:
1. Only the administrator can take control.
2. A projector can display up to 4 computer screens.
EN-62
You can set the name of your computer under Optoma Presenter
Management.
Icon
For details about the icons, please see the following:
Description Icon Description
You are a normal user and have no access to change the password.
You are an administrator and have authority to change the password.
You are the user of the projector.
Disconnects from the projector.
Opens the web page of the Network Control.
There is another user of the projector.
You are an administrator of the projector.
You are a normal user of the projector.
Sets a display zone for the projector.
4. The Setting page allows you to configure Optoma Presenter.
i.
To change the Optoma Presenter interface language, click the down arrow to reveal a drop-down list and select a desired language. Click
Apply.
EN-63
ii. To allow notification messages to appear, click Yes. Click Apply.
iii. To adjust the image quality, click the down arrow to reveal a dropdown list and select a desired quality level. The higher image quality you select, the higher network transfer speed is required. Click Apply after your selections.
iv. To enable audio out, click Yes. Click Apply.
v. The Software Information is available on this page.
EN-64
Displaying pictures with a USB storage device
The projector is built-in an application which can display packaged images on a USB storage device. It can eliminate the need for a computer source.
The projector supports the following image formats:
File format Maximum pixel size
JPEG
GIF/TIFF/PNG/BMP
8000 x 8000
1280 x 800
Progressive JPEG files are not supported.
Some JPEG files may not be displayed clearly.
To display the images on a USB storage device:
1. Plug the USB storage device into the FLASH DRIVE socket.
2. The projector automatically displays the main screen. Or your can manually select Flash drive from the source selection bar.
3. Press “Enter” to display the content of your USB storage device.
4. When only one USB is plugged, folders and supported files are represented in thumbnail mode.
To scroll through the thumbnails, use the four directional arrow keys.
To open a folder/file, press “Enter”.
Icon Description
Go to the top level of the selected USB
Go to previous level of folder
Setup function
EN-65
Setup function
Select another USB
Use the four directional arrow keys to highlight options.
Press “Enter” to switch the settings of the highlighted function.
Go back to thumbnail file, press .
Thumbnail Order Description
File order by time
Sort by recent update to past
File order by characters
It is sorted by first character of file name.
Folder (0-9,a-z,symbols)
Files (0-9,a-z,symbols)
Slidesow Description
Sets the time interval each image displays.
Sets the way the slide show is displayed.
Sets whether to repeat the slide shows.
EN-66
5. When more than one USB is plugged, press “Enter” to switch to another
USB.
Slide shows
1. When user press "Enter" into a picture, it will display picture auto fit to the screen by retaining original size ratio.
2. Press "Enter" key to shows setting bar.
Icon Description
Keep slideshow
Stop slideshow and only display this picture
Go back to thumbnail file
When it’s on slideshow
:
Press button Action
EN-67
Right
Left
Enter
Menu
Jump to next photo and keep slideshow
Jump to previous photo and keep slideshow
Show setting bar
Show projector menu
When it's only displaying one picture:
Press button
Up
Down
Rotate +90
Rotate -90
°
°
Action
Right
Left
Enter
Menu
Jump to next photo
Jump to previous photo
Show setting bar
Show projector menu
EN-68
Appendix
Replacing the Dust Filter
Be sure to follow the steps to replace the dust filter.
The dust filter should be cleaned or replaced periodically (suggest after every 500 hours or 3 months of use). If it is not cleaned periodically, it can become clogged with dust and prevent the projector from being ventilated properly. This can cause over heating and damage the projector. If the projector is used in a dusty environment, be sure to cleaned or replaced the dust filter more frequently.
1. Remove the dust filter, located at the rear side of the projector, by pulling it out as the illustration.
dust filter
2. Clean the dust filter .
To clean the dust filter, you are advised to use a small vacuum cleaner designed for computers and other office equipment.
If the dust filter is torn, replace it.
3. Turn on the projector, then press “Menu”, go to
OPTIONS > Optional Filter > Optional Filter Installed and select “Yes”.
4. Turn on the projector, then press “Menu”, go to OPTIONS > Optional
Filter > Optional Filter Installed and select “No” when you pull out the dust filter and would not use it again.
EN-69
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage.
We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement.
Note
The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald your finger. When you replace the lamp, wait for at least 45 minutes for the lamp to cool down.
Do not touch the lamp glass at any time. The lamp may explode due to improper handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.
A lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5 minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible material nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable substance, such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness, and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the lamp will be exposed. Leave the area immediately if the lamp shatters while being operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to user’s health.
EN-70
1. Turn off the projector.
2. Unplug the power cord.
3. Open the top cover, by sliding the top cover forward, and lifting the top cover off.1
4. Remove the screw on the lamp cover and then open it up. 2 & 3
5. Loosen the screws from the lamp module. 4
6. Raise the handle and pull out the lamp module slowly and carefully. 5
7. Insert the new lamp module into the projector and tighten the screws.
8. Replace the lamp cover and tighten the screw.
9. Replace the top cover by (a) aligning the cover (b) sliding it toward the back and (c) locking it back into place.
10. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
11. Reset the lamp hour. Refer to the “OPTIONS > Lamp Settings” menu.
Note
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before replacing the lamp.
Do not use the projector with the lamp cover removed.
EN-71
Ceiling mount installation
1. To prevent damage to your projector, please use the Optoma ceiling mount.
2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications:
Screw type: M4*3
Maximum screw length: 10mm
Minimum screw length: 8mm
110
82.3
Lens
80.89
Unit: mm
65.04
Note
Please note that damage resulting from incorrect installation will void the warranty.
Warning
1.If you buy a ceiling mount from another company, please be sure to use the correct screw size. Screw length will vary depending on the thickness of the mounting plate.
2.Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
3.Avoid installing the projector near a heat source.
EN-72
Compatibility Modes
Computer Compatibility
VGA
SVGA
XGA
Signal Resolution
640 X 480
800 X 600
1024 X768
HDTV(720P)
WXGA
WXGA+
SXGA
SXGA+
UXGA
HDTV(1080p)
WUXGA
1280 X 720
1280 X768
1280 X800
1366 X 768
1440 X 900
1280 X1024
1400 X1050
1600 X 1200
1920 X1080
1920 X1200(*)
(*)1920 x 1200 @60hz only support reduced blanking
(**) 3D timing for True 3D projector
60
60
60
60
Refresh Rate(Hz) Notes for Mac
60/67/72/85 Mac 60/72/85
60(**)/72/85/120(**) Mac 60/72/85
60(**)/70/75/85/
120(**)
Mac 60/70/75/85
50/60(**)/120(**) Mac 60
60/75/85
60(**)/120(**)
60
60
60
Mac 60/75/85
Mac 60
Mac 60
Mac 60
Mac 60/75
Mac 60
Mac 60
EN-73
Input Signal for HDMI
VGA
SVGA
XGA
Signal Resolution
640 X 480
800 X 600
1024 X 768
SDTV(480I)
SDTV(480P)
SDTV(576I)
SDTV(576P)
640 X 480
640 X 480
720 X 576
720 X 576
WSVGA(1024X600) 1024 X 600
HDTV(720p) 1280 X 720
WXGA 1280 X768
1280 X800
WXGA+
SXGA
SXGA+
UXGA
HDTV(1080I)
HDTV(1080p)
WUXGA
1366 x 768
1440 x 900
1280 X1024
1400 X1050
1600 X 1200
1920 X1080
1920 X1080
1920 X1200(*)
(*)1920 x 1200 @60hz only support reduced blanking
(**)3D timing for True 3D projector
60
60
50
50
Refresh Rate(Hz) Notes for Mac
60 Mac 60/72/85
60(**)/72/85/120(**) Mac 60/72/85
60(**)/70/75/85/
120(**)
Mac 60/70/75/85
60
50(**)/60/120(**)
60/75/85
60(**)/120(**)
60
60
60/75/85
60
60
50/60
24/30/50/60
60
Mac 60
Mac 75
Mac 60
Mac 60
Mac 60
Mac 60/75
Mac 60
Mac 60
EN-74
True 3D Video Compatibility table
Input Resolutions
HDMI 1.4a
3D Input
HDMI 1.3
Input timing
1280 X 720P @ 50Hz Top - and - Bottom
1280 X 720P @ 60Hz Top - and - Bottom
1280 X 720P @ 50Hz Frame packing
1280 X 720P @ 60Hz Frame packing
1920 X 1080i @50 Hz Side- by-Side (Half)
1920 X 1080i @60 Hz Side- by-Side (Half)
1920 X 1080P @24 Hz Top - and - Bottom
1920 X 1080P @24 Hz Frame packing
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @60Hz
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @60Hz
480i
Side-by-
Side(Half)
Top-and-
Bottom
HQFS
SBS mode is on
TAB mode is on
3D format is
Frame sequential
If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D mode
Support NVIDIA 3DTV Play if there is no patent fee from Optoma
1080i@25hz and 720p@50hz will run in 100hz; other 3D timing will run in 120hz.
1080P@24hz will run 144Hz.
Video Compatibility
NTSC
PAL
SECAM
Component
SDTV
HDTV
NTSC M/J, 3.58MHz, 4.43MHz
PAL B/D/G/H/I/M/N, 4.43MHz
SECAM B/D/G/K/K1/L, 4.25/4.4 MHz
480i/p, 576i/p, 720p(50/60Hz), 1080i(50/60Hz)
1080P(24/50/60Hz)
480i/p, 576i/p
720p(50/60Hz), 1080i(50/60Hz), 1080P(50/60Hz)
EN-75
IR Code
Customer code: 32CD
Key code Printing-key definition
81
3E
Power on/off
Switch
C3
97
C4
CB
CC
Source
User
Re-Sync
L
R
C6
C8
C9
Up arrow
Left arrow
Right arrow
EN-76
87
88
89
86
85
84
8C
8F
8B
8A
83
8E
8D
96
93
C7
C5
CA
N/A
C1
95
C2
Down arrow
Enter
Enter
Laser
Page+
Mode
Page-
Keystone+
Keystone-
Volume +
Volume -
Brightness/1
Menu/2
Zoom/3
HDMI/4
Freeze/5
AV mute/6
S-Video/7
VGA/8
Video/9
Eco
+
3D
The IR codes below are for user-defined remote only.
79 Power off (single push)
82
80
9A
99
9E
94
Power off
Power on
VGA2
Network Display
DVI
Contrast
EN-77
Telnet Commands
Port: support port 23
Multi-connections: Projector could receive commands from different ports at the same time
Command Format: Follow RS232 command format (support both of
ASCII and HEX)
Command Response: Follow RS232 return message.
Lead Code Projector ID Command ID space variable carriage return
CR ~
Fix code
One Digit
X
00
X X X X
Defined by Optoma
2 or 3 Digit
See the Follow content
One Digit n
Per item
Definition
Fix code
One digit
Note
Note: When the data length is greater or shorter than indicated by the data length code, the projector returns the error code to computer.
EN-78
PJLink commands
Support PJ link: click on below documents (English only)
Name?
INF0?
INF1?
INF2?
RGB1
RGB2
VIDEO1
VIDEO2
DIGITAL1
DIGITAL2
STORAGE1
STORAGE2
NETWORK1
Projector name
Resolution
Optoma
Model name
VGA1
VGA2
Video
S-Video
HDMI
DVI
Flash Drive
USB Display
Network Display
Varies with the different products.
The native resolution of projector and it varies with the different products.
Format:SVGA,XGA,WXGA,1080p, WUXGA
Varies with the different products.
EN-79
AMX Device Discovery commands
UDP : 239.255.250.250
Port No. : 9131
Each UDP broadcast information as below are updated around 40 seconds
Command Description Value
Device-UUID
MAC address(Hex value without ‘:’ separator)
12 digits
Device-
SDKClass
Device-Make
Device-Model
The Duet DeviceSdk class name VideoProjector
MakerPXLW
Projector
Config-URL
Revision
Maker name
Model name
Device’s IP address
LAN IP address is shown up if LAN IP address is valid.
Wireless LAN IP address is shown up if
Wireless LAN IP address is valid.
The revision must follow a major.minor.micro scheme.
The revision is only increased if the command protocol is modified.
http://xxx.xxx.xxx.xxx/index.html
1.0.0
Attention
1. This AMX function is only to support AMX Device Discovery.
2. The broadcast information only send out through valid interface.
3. Both LAN and Wireless LAN interfaces could be supported at the same time.
4. If "Beacon Validator" was used. Please take care below information.
EN-80
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
D-Sub 9 pin
(from the projector side)
1 1 CD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
(from the cable side)
6
7
4
5
8
2
3
C1
1
9
SHELL
COLOR
Black
Brown
Red
Orange
Yellow
Green
Blue
Purple
White
DW
4
8
6
5
7
3
2
C2
1
9
SHELL
EN-81
RS232 Protocol Function List
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
UART16550 FIFO
Projector Return (Pass)
Projector Return (Fail)
9600
8
None
1
None
Disable
P
F
Lead Code
~
Fix code
One Digit
Projector ID
X X
Set in OSD
00~99
Two Digit
X
Command ID
X X
Defined by Optoma
2 or 3 Digit
See the Follow content space variable n
One Digit
Per item
Definition carriage return
CR
Fix code
One digit
Note
To also include AMX beacon signal in RS232 protocol
In basic terms, AMX controllers will issue a poll periodically to detect 3rd party devices connected to the RS232 port (in this case Optoma). The poll is "AMX" in ASCII followed by a carriage return 'r'.
There is a <CR> after all ASCII commands.
0D is the HEX code for <CR> in ASCII code
EN-82
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SEND to projector
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX00 1
~XX00 0
7E 30 30 30 30 20 31 0D
7E 30 30 30 30 20 30 0D
Power ON
Power OFF (0/2 for backward compatible)
~XX00 1 ~nnnn 7E 30 30 30 30 20 31 20 a 0DPower ON with Password ~nnnn = ~0000 (a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX01 1 7E 30 30 30 31 20 31 0D Resync
~XX02 1
~XX02 0
~XX03 1
~XX03 0
~XX04 1
7E 30 30 30 32 20 31 0D AV Mute
7E 30 30 30 32 20 30 0D
7E 30 30 30 33 20 31 0D Mute
7E 30 30 30 33 20 30 0D
7E 30 30 30 34 20 31 0D Freeze
On
Off (0/2 for backward compatible)
On
Off (0/2 for backward compatible)
~XX04 0
~XX05 1
~XX06 1
~XX12 1
~XX12 3
~XX12 5
~XX12 6
~XX12 8
~XX12 9
~XX12 10
~XX12 13
~XX12 17
~XX12 18
7E 30 30 30 34 20 30 0D
7E 30 30 30 35 20 31 0D
7E 30 30 30 36 20 31 0D
7E 30 30 31 32 20 31 0D
7E 30 30 31 32 20 33 0D
7E 30 30 31 32 20 35 0D
7E 30 30 31 32 20 36 0D
Unfreeze
Zoom Plus
Zoom Minus
Direct Source Commands
7E 30 30 31 32 20 38 0D
7E 30 30 31 32 20 39 0D
7E 30 30 31 32 20 31 30 0D
7E 30 30 31 32 20 31 33 0D
7E 30 30 31 32 20 31 37 0D
7E 30 30 31 32 20 31 38 0D
HDMI
DVI-I
VGA1
VGA 2
(0/2 for backward compatible)
VGA1 Component
S-Video
Video
VGA 2 Component
Flash drive
Network Display
~XX12 19 7E 30 30 31 32 20 31 39 0D USB display
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX20 1
~XX20 2
7E 30 30 32 30 20 31 0D
7E 30 30 32 30 20 32 0D
Display Mode Presentation
Bright
~XX20 3
~XX20 4
~XX20 5
7E 30 30 32 30 20 33 0D
7E 30 30 32 30 20 34 0D
7E 30 30 32 30 20 35 0D
Movie sRGB
User
~XX20 7
~XX20 13
7E 30 30 32 30 20 37 0D
7E 30 30 32 30 21 33 0D
Blackboard
DICOM SIM.
~XX20 9 7E 30 30 32 30 20 39 0D 3D
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX21 n
~XX22 n
7E 30 30 32 31 20 a 0D
7E 30 30 32 32 20 a 0D
Brightness
Contrast n = -50 (a=2D 35 30) ~ 50 (a=35 30) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX23 n 7E 30 30 32 33 20 a 0D Sharpness n = 1 (a=31) ~ 15 (a=31 35)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- -----------------------------
~XX24 n
~XX25 n
7E 30 30 32 34 20 a 0D
7E 30 30 32 35 20 a 0D
Color Settings/White Red
Green n = -50 (a=2D 35 30) ~ 50 (a=35 30) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n 7E 30 30 32 36 20 a 0D Blue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1 7E 30 30 33 33 20 31 0D Reset
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX34 n 7E 30 30 33 34 20 a 0D BrilliantColor TM n = 1 (a=31) ~ 10 (a=31 30)
~XX35 1
~XX35 2
~XX35 3
~XX35 4
~XX35 5
7E 30 30 33 35 20 31 0D
7E 30 30 33 35 20 32 0D
7E 30 30 33 35 20 33 0D
7E 30 30 33 35 20 34 0D
7E 30 30 33 35 20 35 0D
Gamma Film
Video
Graphics
2.2
1.8
~XX35 6
~XX35 7
7E 30 30 33 35 20 36 0D
7E 30 30 33 35 20 37 0D
2.0
2.6
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX36 1 7E 30 30 33 36 20 31 0D Color Temp. Warm
~XX36 2
~XX36 3
~XX37 1
7E 30 30 33 36 20 32 0D
7E 30 30 33 36 20 33 0D
7E 30 30 33 37 20 31 0D Color Space
Medium
Cold
Auto
~XX37 2
~XX37 3
~XX37 4
~XX73 n
7E 30 30 33 37 20 32 0D
7E 30 30 33 37 20 33 0D
7E 30 30 33 37 20 34 0D
7E 30 30 37 33 20 a 0D Signal
RGB\ RGB(0-255)
YUV
RGB(16 - 235)
Frequency n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX91 1
~XX91 0
~XX74 n
7E 30 30 39 31 20 31 0D
7E 30 30 39 31 20 30 0D
7E 30 30 37 34 20 a 0D
Automatic On
Off
Phase n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n
~XX76 n
7E 30 30 37 35 20 a 0D
7E 30 30 37 36 20 a 0D
H. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
V. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX44 n 7E 30 30 34 35 20 a 0D Tint n = -50 (a=2D 35 30) ~ 50 (a=35 30))
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX60 1
~XX60 2
~XX60 3
~XX60 5
7E 30 30 36 30 20 31 0D
7E 30 30 36 30 20 32 0D
7E 30 30 36 30 20 33 0D
7E 30 30 36 30 20 35 0D
Format 4:3
16:9
16:10(W501)
LBX
~XX60 6 7E 30 30 36 30 20 36 0D Native
~XX60 7 7E 30 30 36 30 20 37 0D Auto
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX61 n
~XX62 n
~XX63 n
~XX64 n
~XX66 n
~XX69 1
~XX69 0
~XX230 1
7E 30 30 36 31 20 a 0D
7E 30 30 36 32 20 a 0D
7E 30 30 36 33 20 a 0D
7E 30 30 36 34 20 a 0D
7E 30 30 36 36 20 a 0D
7E 30 30 36 39 20 31 0D
7E 30 30 36 39 20 30 0D
Edge mask
Zoom
H Image Shift
V Image Shift
V Keystone
Auto Keystone
Auto Keystone
7E 30 30 32 33 30 20 31 0D 3D Mode n = 0 (a=30) ~ 10 (a=31 30) n = -5 (a=2D 35) ~ 25 (a=32 35) n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30) n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30) n = -40 (a=2D 34 30) ~ 40 (a=34 30)
On
Off
DLP-Link
EN-83
~XX230 3
~XX400 0
~XX400 1
~XX400 2
~XX405 0
7E 30 30 32 33 30 20 31 0D 3D Mode IR
7E 30 30 34 30 30 20 30 0D 3D Ш2D 3D
7E 30 30 34 30 30 20 31 0D
7E 30 30 34 30 30 20 32 0D
7E 30 30 34 30 35 20 30 0D 3D Format
L
R
Auto
~XX405 1
~XX405 2
~XX405 3
~XX231 0
7E 30 30 34 30 35 20 31 0D
7E 30 30 34 30 35 20 32 0D
7E 30 30 34 30 35 20 33 0D
7E 30 30 32 33 31 20 30 0D 3D Sync Invert
SBS
Top and Bottom
Frame sequential
On
~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX70 1
~XX70 2
~XX70 3
~XX70 4
~XX70 5
~XX70 6
~XX70 7
7E 30 30 37 30 20 31 0D
7E 30 30 37 30 20 32 0D
7E 30 30 37 30 20 33 0D
7E 30 30 37 30 20 34 0D
7E 30 30 37 30 20 35 0D
7E 30 30 37 30 20 36 0D
7E 30 30 37 30 20 37 0D
Language English
German
French
Italian
Spanish
Portuguese
Polish
~XX70 8
~XX70 9
~XX70 10
~XX70 11
~XX70 12
~XX70 13
~XX70 14
~XX70 15
~XX70 16
~XX70 17
~XX70 18
~XX70 19
~XX70 20
7E 30 30 37 30 20 38 0D
7E 30 30 37 30 20 39 0D
7E 30 30 37 30 20 31 30 0D
7E 30 30 37 30 20 31 31 0D
7E 30 30 37 30 20 31 32 0D
7E 30 30 37 30 20 31 33 0D
7E 30 30 37 30 20 31 34 0D
7E 30 30 37 30 20 31 35 0D
7E 30 30 37 30 20 31 36 0D
7E 30 30 37 30 20 31 37 0D
7E 30 30 37 30 20 31 38 0D
7E 30 30 37 30 20 31 39 0D
7E 30 30 37 30 20 32 30 0D
Dutch
Swedish
Norwegian/Danish
Finnish
Greek
Traditional Chinese
Simplified Chinese
Japanese
Korean
Russian
Hungarian
Czechoslovak
Arabic
~XX70 21
~XX70 22
~XX70 23
~XX70 25
7E 30 30 37 30 20 32 31 0D
7E 30 30 37 30 20 32 32 0D
7E 30 30 37 30 20 32 33 0D
7E 30 30 37 30 20 32 33 0D
Thai
Turkish
Farsi
Vietnamese
~XX70 26 7E 30 30 37 30 20 32 33 0D Indonesian
~XX70 27 7E 30 30 37 30 20 32 33 0D Romanian
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX71 1
~XX71 2
~XX71 3
~XX71 4
7E 30 30 37 31 20 31 0D
7E 30 30 37 31 20 32 0D
7E 30 30 37 31 20 33 0D
7E 30 30 37 31 20 34 0D
Projection Front-Desktop
Rear-Desktop
Front-Ceiling
Rear-Ceiling
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX72 1 7E 30 30 37 32 20 31 0D Menu Location Top Left
~XX72 2
~XX72 3
~XX72 4
~XX72 5
7E 30 30 37 32 20 32 0D
7E 30 30 37 32 20 33 0D
7E 30 30 37 32 20 34 0D
7E 30 30 37 32 20 35 0D
Top Right
Centre
Bottom Left
Bottom Right
(EW501 only)
~XX90 1 7E 30 30 39 31 20 31 0D Screen Type 16:10
~XX90 0 7E 30 30 39 31 20 30 0D 16:9
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX77 n 7E 30 30 37 37 20 aabbcc 0D Security
(aa=31 32)
Security Timer Month/Day/Hour n = mm/dd/hhmm= 00 (aa=30 30) ~ 12 dd = 00 (bb=30 30) ~ 30 (bb=33 30) hh= 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1 7E 30 30 37 38 20 31 0D
~XX78 0 ~nnnn 7E 30 30 37 38 20 32 20 a 0D
Security Settings Enable
Disable(0/2 for backward compatible) ~nnnn = ~0000
(a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX80 1 7E 30 30 38 30 20 31 0D Mute On
~XX80 0
~XX310 0
7E 30 30 38 30 20 30 0D
7E 30 33 31 30 20 30 0D Internal Speaker
Off (0/2 for backward compatible)
Off
~XX310 1
~XX81 n
~XX93 n
7E 30 33 31 30 20 31 0D
7E 30 30 38 31 20 a 0D
7E 30 30 39 33 20 a 0D
Volume(Audio)
Volume(Mic)
On n = 0 (a=30) ~ 10 (a=31 30) n = 0 (a=30) ~ 10 (a=31 30)
~XX89 0
~XX89 1
~XX89 3
~XX89 4
7E 30 30 38 39 20 30 0D
7E 30 30 38 39 20 31 0D
7E 30 30 38 39 20 33 0D
7E 30 30 38 39 20 34 0D
Audio Input Default
Audio1
Audio2
Audio3
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX82 1 7E 30 30 38 32 20 31 0D Logo Default
~XX82 2
~XX82 3
~XX83 1
~XX88 0
7E 30 30 38 32 20 32 0D
7E 30 30 38 32 20 33 0D
7E 30 30 38 33 20 31 0D
7E 30 30 38 38 20 30 0D
Logo Capture
Closed Captioning
User
Neutral
~XX88 1
~XX88 2
7E 30 30 38 38 20 31 0D
7E 30 30 38 38 20 32 0D
Off cc1 cc2
~XX450 0
~XX450 1
~XX454 0
~XX454 1
7E 30 30 34 35 30 20 30 0D WLAN
7E 30 30 34 35 30 20 31 0D
7E 30 30 34 35 34 20 30 0D Crestron
7E 30 30 34 35 34 20 31 0D
Off
On
Off
On
EN-84
~XX455 0
~XX455 1
~XX456 0
~XX456 1
~XX457 0
~XX457 1
~XX458 0
~XX458 1
7E 30 30 34 35 35 20 30 0D Extron
7E 30 30 34 35 35 20 31 0D
7E 30 30 34 35 36 20 30 0D PJLink
7E 30 30 34 35 36 20 31 0D
7E 30 30 34 35 37 20 30 0D AMX Device Discovery
7E 30 30 34 35 37 20 31 0D
7E 30 30 34 35 38 20 30 0D Telnet
7E 30 30 34 35 38 20 31 0D
Off
On
Off
On
Off
On
Off
On
~XX459 0
~XX459 1
7E 30 30 34 35 38 20 30 0D HTTP
7E 30 30 34 35 38 20 31 0D
Off
On
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX100 1 7E 30 30 31 30 30 20 31 0D Source Lock On
~XX100 0
~XX101 1
7E 30 30 31 30 30 20 30 0D
7E 30 30 31 30 31 20 31 0D High Altitude
Off (0/2 for backward compatible)
On
~XX101 0
~XX102 1
~XX102 0
~XX103 1
7E 30 30 31 30 31 20 30 0D
7E 30 30 31 30 32 20 31 0D Information Hide
7E 30 30 31 30 32 20 30 0D
7E 30 30 31 30 33 20 31 0D Keypad Lock
Off (0/2 for backward compatible)
On
Off (0/2 for backward compatible)
On
~XX103 0
~XX195 0
~XX195 1
~XX195 2
~XX192 0
~XX192 1
~XX192 3
7E 30 30 31 30 33 20 30 0D
7E 30 30 31 39 35 20 30 0D Test Pattern
7E 30 30 31 39 35 20 31 0D
7E 30 30 31 39 35 20 32 0D
7E 30 30 31 39 32 20 30 0D 12V Trigger
7E 30 30 31 39 32 20 31 0D
7E 30 30 31 39 32 20 33 0D
Off (0/2 for backward compatible)
None
Grid
White Pattern
Off
On
Auto 3D
~XX11 0
~XX11 1
~XX11 2
7E 30 30 31 31 20 30 0D IR Function
7E 30 30 31 31 20 31 0D
7E 30 30 31 31 20 32 0D
Off
On
Front
Back ~XX11 3 7E 30 30 31 31 20 33 0D
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX104 1 7E 30 30 31 30 34 20 31 0D Background Color Blue
~XX104 2
~XX104 3
7E 30 30 31 30 34 20 32 0D
7E 30 30 31 30 34 20 33 0D
Black
Red
~XX104 4
~XX104 5
7E 30 30 31 30 34 20 34 0D
7E 30 30 31 30 34 20 35 0D
Green
White
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX105 1 7E 30 30 31 30 35 20 31 0D Advanced Direct Power On On
~XX105 0
~XX113 0
~XX113 1
7E 30 30 31 30 35 20 30 0D
7E 30 30 31 31 33 20 30 0D
7E 30 30 31 31 33 20 31 0D
Off (0/2 for backward compatible)
Signal Power On Off
On
~XX106 n
30)
7E 30 30 31 30 36 20 a 0D
(5 minutes for each step).
~XX107 n
30)
7E 30 30 31 30 37 20 a 0D
(30 minutes for each step).
~XX115 1 7E 30 30 31 31 35 20 31 0D
~XX115 0 compatible)
7E 30 30 31 31 35 20 30 0D
~XX114 1
~XX114 0 compatible)
7E 30 30 31 31 34 20 31 0D
7E 30 30 31 31 34 20 30 0D
Power Mode(Standby) Eco.(<=0.5W)
Auto Power Off (min)
Sleep Timer (min)
n = 0 (a=30) ~ 180 (a=31 38
n = 0 (a=30) ~ 990 (a=39 39
Quick Resume On
Off (0/2 for backward
Active (0/2 for backward
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX109 1 7E 30 30 31 30 39 20 31 0D Lamp Reminder On
~XX109 0
~XX110 1
~XX110 3
~XX110 4
7E 30 30 31 30 39 20 30 0D
7E 30 30 31 31 30 20 31 0D
7E 30 30 31 31 30 20 33 0D
7E 30 30 31 31 30 20 34 0D
Brightness Mode
Off (0/2 for backward compatible)
Bright
Eco
+
Dynamic
~XX111 1
~XX111 0
7E 30 30 31 31 31 20 31 0D
7E 30 30 31 31 31 20 30 0D
Lamp Reset Yes
No (0/2 for backward compatible)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX320 1 7E 30 30 33 32 30 20 31 0D Optional Filter Installed Yes
~XX320 0 compatible)
7E 30 30 33 32 30 20 30 0D No (0/2 for backward
~XX322 0
~XX322 1
~XX322 2
~XX322 3
7E 30 30 33 32 32 20 30 0D
7E 30 30 33 32 32 20 31 0D
7E 30 30 33 32 32 20 32 0D
7E 30 30 33 32 32 20 33 0D
Filter Reminder Off
300 hr
500 hr
800 hr
~XX322 4
~XX323 1
~XX323 0
7E 30 30 33 32 32 20 34 0D
7E 30 30 33 32 33 20 31 0D
7E 30 30 33 32 33 20 30 0D
Filter Reset
1000 hr
Yes
No(0/2 for backward compatible)
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX112 1 7E 30 30 31 31 32 20 31 0D Reset Yes
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX99 1
~XX210 n
7E 30 30 39 39 20 31 0D RS232 Alert Reset Reset System Alert
7E 30 30 32 30 30 20 n 0D Display message on the OSD n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------
SEND to emulate Remote
~XX140 10 7E 30 30 31 34 30 20 31 30 0D
~XX140 11
~XX140 12
7E 30 30 31 34 30 20 31 31 0D
7E 30 30 31 34 30 20 31 32 0D
~XX140 13
~XX140 14
~XX140 15
~XX140 16
~XX140 17
7E 30 30 31 34 30 20 31 33 0D
7E 30 30 31 34 30 20 31 34 0D
7E 30 30 31 34 30 20 31 35 0D
7E 30 30 31 34 30 20 31 36 0D
7E 30 30 31 34 30 20 31 37 0D
Up
Left
Enter (for projection MENU)
Right
Down
Keystone +
Keystone –
Volume –
EN-85
~XX140 18
~XX140 19
~XX140 20
~XX140 21
7E 30 30 31 34 30 20 31 38 0D
7E 30 30 31 34 30 20 31 39 0D
7E 30 30 31 34 30 20 32 30 0D
7E 30 30 31 34 30 20 32 31 0D
Volume +
Brightness
Menu
Zoom
~XX140 47 7E 30 30 31 34 30 20 34 37 0D Source
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SEND from projector automatically
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Projector
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ when Standby/Warming/Cooling/Out of
Range/Lamp fail/Fan Lock/Over Temperature/
Lamp Hours Running Out/Cover Open
INFOn n : 0/1/2/3/4/6/7/8/ = Standby/Warming/Cooling/Out of
Range/Lamp fail/Fan Lock/Over Temperature/Lamp Hours
Running Out/Cover Open
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
READ from projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Return
~XX121 1
~XX122 1
~XX123 1
7E 30 30 31 32 31 20 31 0D Input Source Commands
7E 30 30 31 32 32 20 31 0D Sofware Version
7E 30 30 31 32 33 20 31 0D Display Mode
None/Presentation/Bright/Movie/sRGB/User/Blackboard/DICOM SIM./3D
OKn
OKdddd
OKn n: 0/1/2/3/4/5/6/7/8/9 =
None/VGA1/VGA2/Video/S-Video/HDMI/DVI/Flash drive/Network display/USB display dddd: FW version n : 0/1/2/3/4/5/6/7/8/
~XX124 1
~XX125 1
~XX126 1
~XX127 1
7E 30 30 31 32 34 20 31 0D Power State
7E 30 30 31 32 35 20 31 0D Brightness
7E 30 30 31 32 36 20 31 0D Contrast
7E 30 30 31 32 37 20 31 0D Format
OKn
OKn
OKn
Okn n : 0/1 = Off/On
(W501) n: 0/1/2/3/4/5 =
4:3/16:9/16:10/LBX/Native/AUTO
(EH501) n: 0/1/2/3/4 =4:3/16:9/LBX/Native/AUTO
(X501) n: 0/1/2/3 =4:3/16:9/Native/AUTO
*16:9 or 16:10 depend on Screen Type setting
~XX128 1
~XX129 1
Rear-Ceiling
7E 30 30 31 32 38 20 31 0D Color Temperature
7E 30 30 31 32 39 20 31 0D Projection Mode
OKn
OKn n : 0/1/2 = Warm/Medium/Cold n : 0/1/2/3 = Front-Desktop/ Rear-Desktop/ Front-Ceiling/
~XX150 1 7E 30 30 31 35 30 20 31 0D Information OKabbbbccdddde a : 0/1 = Off/On
None/VGA1/VGA2/Video/S-Video/HDMI/DVI/Flash Drive/Network display/USBdisplay cc: source 00/01/02/03/04/05/06/07/08/09 = dddd: FW version e : Display mode 0/1/2/3/4/5/6/7/8/
None/Presentation/Bright/Movie/sRGB/User/
Blackboard/ DICOM SIM /3D
~XX151 1
~XX108 1
~XX108 2
Hours
~XX321 1
~XX87 1
~XX87 3
~XX451 1
~XX451 2
~XX451 3
7E 30 30 31 35 31 20 31 0D Model name
7E 30 30 31 30 38 20 31 0D Lamp Hours
7E 30 30 31 30 38 20 31 0D
7E 30 30 33 32 31 20 31 0D
7E 30 30 38 37 20 31 0D Network Status
7E 30 30 38 37 20 33 0D IP Address
7E 30 30 34 35 31 20 31 0D WLAN Network Status
7E 30 30 34 35 31 20 32 0D WLAN IP Address
7E 30 30 34 35 31 20 33 0D SSID
OKn
OKbbbb n:1/2/3=X501/W501/EH501 bbbb: LampHour
Cumulative Lamp Hours OKbbbbb bbbbb: (5 digits) Total Lamp
Filter Usage Hours OKbbbb
Okn bbbb: Filter Usage Hours n=0/1 Disconnected/Connected
Okaaa_bbb_ccc_ddd
Okn n=0/1 Disconnected/Connected
Okaaa_bbb_ccc_ddd
Okaaaaaaaaaaaaaaaaaaaa
EN-86
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well.
Start-up
If no lights turn on:
Be sure that the power cord is securely connected to the projector and the other end is plugged into an outlet with power.
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press the power button again.
Image
If the searching source is displayed:
Press SOURCE on the projector or Source on the remote control to select an active input source.
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computer’s external video port is turned on. Refer to the computer manual.
If the image is out of focus:
While displaying the on-screen menu, adjust the focus ring. (The image size should not change; if it does, you are adjusting the zoom, not the focus.)
Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
Press “Menu”, go to IMAGE > Advanced > Signal and adjust Phase or
Frequency.
Remote control
If the remote control does not operate:
Be sure nothing is blocking the remote control receiver on the front of the projector. Use the remote control within the effective range.
Aim the remote control at the screen or at the front of the projector.
Move the remote control so it is more directly in front of the projector and not as far to the side.
EN-87
LED Indicator Messages
Message
Standby State
(Input power cord)
Power on
(Warming)
Power on & Lamp lighting
Power off
(Cooling)
Power LED
(Red)
Steady light
Power LED
(Green)
Flashing
0.5 sec off
0.5 sec light
Steady light
Flashing
0.5 sec off
0.5 sec light
Back to Red steady light when cooling fan turns off
Flashing
0.25 sec off
0.25 sec light
Quick Resume
(100 secs)
Error
(Lamp fail)
Error
(Fan fail)
Error
(Over Temp)
Standby State
(Burn in mode)
Burnin
(Warming)
Burnin
(Cooling)
Flashing
Flashing
Flashing
Flashing
Flashing
Flashing
Temp LED
(Red)
Flashing
Steady light
Lamp LED
(Red)
Steady light
EN-88
Optoma Global Offices
For service or support please contact your local office.
USA
3178 Laurelview Ct.
Fremont, CA 94538, USA www.optomausa.com
888-289-6786 [email protected]
Canada
3178 Laurelview Ct.
Fremont, CA 94538, USA www.optomausa.com
Europe
42 Caxton Way, The Watford Business
Park
Watford, Hertfordshire,
WD18 8QZ, UK www.optoma.eu
Service Tel : +44 (0)1923 691865
France
Batiment E
81-83 avenue Edouard Vaillant
92100 Boulogne Billancourt, France
Spain
C/ Jose Hierro,36 Of. 1C
28522 Rivas VaciaMadrid,
Spain
Deutschland
Wiesenstrasse 21 W
D40549 Dusseldorf,
Germany
888-289-6786 [email protected]
+44 (0) 1923 691 800
+44 (0) 1923 691 888 [email protected]
+33 1 41 46 12 20
+33 1 41 46 94 35 [email protected]
+34 91 499 06 06
+34 91 670 08 32
+49 (0) 211 506 6670
+49 (0) 211 506 66799 [email protected]
EN-89
Scandinavia
Lerpeveien 25
3040 Drammen
Norway
PO.BOX 9515
3038 Drammen
Norway
Latin America
3178 Laurelview Ct.
Fremont, CA 94538, USA www.optoma.com.br
Korea
WOOMI TECH.CO.,LTD.
4F,Minu Bldg.33-14, Kangnam-Ku, seoul,135-815, KOREA
888-289-6786 www.optoma.com.mx
+82+2+34430004
+82+2+34430005
Japan
東京都足立区綾瀬 3-25-18
株式会社オーエス [email protected]
コンタクトセンター：0120-380-495 www.os-worldwide.com
Taiwan
12F., No.215, Sec. 3, Beixin Rd.,
Xindian Dist., New Taipei City 231,
Taiwan, R.O.C.
www.optoma.com.tw
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street,
Cheung Sha Wan,
Kowloon, Hong Kong
+47 32 98 89 90
+47 32 98 89 99 [email protected]
+886-2-8911-8600
+886-2-8911-6550 [email protected]
asia.optoma.com
+852-2396-8968
+852-2370-1222 www.optoma.com.hk
EN-90
中国
上海市长宁区
凯旋路 1205 号 5 楼
琉璃奥图码
+86-21-62947376
+86-21-62947375 www.optoma.com.cn
EN-91
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, detectable by turning the equipment in question off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to an outlet on a different circuit than that which the receiver is connected to
Or consult the dealer or an experienced radio/TV technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications
Commission, to operate this projector.
EN-92
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque ą l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
EMC Directive 2004/108/EC (including amendments)
Low Voltage Directive 2006/95/EC
R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.
EN-93
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement