For Connecting Four Pairs of Speakers to an Amplifier or Receiver

For Connecting Four Pairs of Speakers to an Amplifier or Receiver
DATA SHEET
For Connecting Four
Pairs of Speakers to an
Amplifier or Receiver
FOUR ZONE SPEAKER SELECTOR
S-4
S-4
FOUR ZONE SPEAKER SELECTOR
FEATURES
• Safely connect up to four speaker pairs to a single amplifier or receiver
• High power handling capability
• Built-in protection circuit
• Compatible with all 4 ohm capable amplifiers or receivers
• Non skid feet for unit stability
• Includes customized room labels
INSTALLATION FRIENDLY DESIGN:
• Accepts up to 14 gauge wire
• Snap and lock connector secures wire in place without the use of
a screwdriver
SPECIFICATIONS:
• Power handling: 100 watts per channel
• Frequency response: +0 dB, -0 dB (flat) from 20Hz to 20kHz
WIRING REQUIREMENTS:
• Individual runs of 2-conductor speaker wire to each speaker
• Removable connectors accommodate 14-22 gauge wire (16 gauge
recommended)
MOUNTING:
• Table-top
DIMENSIONS:
• 8-1/2" wide x 2" high x 6-3/4" deep
WARRANTY:
• 10 year limited
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P 866.4JB.SITE (866.452.7483)
F 305.238.0185
WWW.JOBSITESYSTEMS.COM
FOUR ZONE SPEAKER SELECTOR
S-4
PREPARING FOR INSTALLATION:
The Speaker wires and Amplifier wires must reach the proposed location of the
S-4 speaker selector. Mark the cables with Wire labels, describing where the
cables originate from, rather than where they will terminate.
INSTALLATION:
1. Select an appropriate location for the S-4.
2. Run all the necessary wiring to the S-4. Label the wires for
future reference.
3. Strip 1/4" of insulation from the end of each wire. Tightly twist the end of
each wire until no frayed ends remain.
4. Locate the Snap and lock connectors and remove them if they are plugged in.
5. Use a small flathead screwdriver or your thumb to raise the locking tabs,
exposing the holes on the connector.
6. Insert each wire into the appropriate hole and snap down the locking tabs.
7. Insert the smooth side of the connector plug into the smooth side of the
S-4 socket.
8. Connect the Receiver or Amplifier to the connector terminal labeled
AMPLIFIER.
9. Connect the Speakers to the connector terminals labeled SPEAKERS.
10. Locate the pre-printed Room Labels. Affix the appropriate label to the
recessed area over each on/off selector button.
S-4 INSTALLATION DIAGRAM
Nil
es
Au
dio
AM
PL
IFIE
R
Co
rpo
rati
on
Mia
mi,
Flo
rid
a
S-4
US
A
SP
EA
KE
R4
SP
EA
KE
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
R3
SP
EA
KE
JobSite S-4
Back
R2
SP
4
3
2
EA
KE
R1
1
P 866.4JB.SITE (866.452.7483)
F 305.238.0185
Stereo Receiver
WWW.JOBSITESYSTEMS.COM
©2004 Niles Audio Corporation. JobSite,
Pure Custom and Niles are registered
trademarks of Niles Audio Corporation
and the JobSite Logo is a trademark of
Niles Audio Corporation. JSS4PDF
Specifications subject to change without notice.
Speaker
Pair 4
Speaker
Pair 3
Speaker
Pair 2
FOUR ZONE SPEAKER SELECTOR
Speaker
Pair 1
S-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising