The Odyn™

The Odyn™
The Odyn
™
Ceiling Fan
Net Weight 14.6 kg
Model No. FPD8148**AU
OWNER'S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
7. Contact your local government for information regarding the collection systems available.
8. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the
food chain, damaging your health and well-being.
9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
10. Children should be supervised to ensure that they do not play with the appliance.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must comply with AS/NZS 3000 Wiring Rules and any local regulations. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation must be made by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 60kg. See page 4 of owner’s manual for support
requirements.
4. The fan must be mounted with the fan blades at least 2.1 meter from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring this ceiling fan.
6. This fan is Not suitable for use with solid-state speed controls.
7. This fan is to be used in dry and damp locations.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product will void your warranty and could result in
personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: This fan MUST be installed with an easily accessible isolating device to disconnect all poles of the fan from the main supply.
The contact distance in all poles must be 3mm minimum.
Table of Contents
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4
Assembling This Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
How to Hang This Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing The Canopy Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembling The Ceiling Fan Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembling The Light Kit Assembly or Cap . . . . . . . . . . . . . . . . . . . .10
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Exploded-View Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
This manual is designed to make it as easy as possible
to assemble, install, operate, and maintain this ceiling fan
Tools Needed for Assembly
Materials
:LULQJDQGFRQQHFWRUVPXVWEHRIW\SHUHTXLUHGE\
ORFDOUHJXODWLRQV7KHPLQLPXPZLUHZRXOGEHD
FRQGXFWRUZLUHZLWKJURXQG
‡2QH3KLOOLSVKHDGVFUHZGULYHU ‡2QHVPDOOEODGH
VXSSOLHG
VFUHZGULYHU
‡2QHVWHSODGGHU
‡2QHZLUHVWULSSHU
ʆWARNING
This fan must be installed be a licensed electrician.
Unpacking Instructions
)RU\RXUFRQYHQLHQFHFKHFNRIIHDFKVWHS$VHDFKVWHSLVFRPSOHWHGSODFHDFKHFNPDUN7KLVZLOOHQVXUHWKDWDOO
VWHSVKDYHEHHQFRPSOHWHGDQGZLOOEHKHOSIXOLQ¿QGLQJ\RXUSODFHVKRXOG\RXEHLQWHUUXSWHG
ʆWARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product could result in
personal injury or property damage.
IF ANY PART IS DAMAGED OR MISSING,
CALL: 1 3 0 0 4 6 9 3 2 6
1. &KHFN WR VHH WKDW \RX KDYH UHFHLYHG WKH IROORZLQJ
SDUWV
NOTE: If you are uncertain of part description, refer to
exploded view illustration.
‡ +DUGZDUHEDJV
‡)DQ0RWRU$VVHPEO\
‡+DQJHU%UDFNHW$VVHPEO\
– 7ZHQW\HLJKWÝ
EODGHWREODGHKROGHU
‡'RZQURG+DQJHU%DOO$VVHPEO\
3DQ+HDG6HUUDWHG6FUHZ
‡&HLOLQJ&DQRS\
– 1LQHWHHQÝ
‡&DQRS\6FUHZ&RYHU$VVHPEO\
EODGHKROGHUWRPRWRU
‡0RWRU&RXSOLQJ&RYHU$VVHPEO\
3DQ+HDG6FUHZ
‡%ODGH&RYHU6HW
– 3KLOOLSV6FUHZGULYHUÝ
‡%ODGH+ROGHU6HW
‡%ODGH6HW
– %DODQFH.LW
‡/LJKW3ODWH$VVHPEO\
– %DJ$VVHPEO\6DIHW\&DEOH
‡/('*ODVV$VVHPEO\
‡$GDSWHU6WHHO&DS6WHHO&DS$VVHPEO\
‡*ODVV
‡+DQG+HOG5HPRWH
Canopy Screw
Cover Assembly
Blade Cover Set
Hanger Bracket
Assembly
Light Plate Assembly
Blade Holder Set
Motor Coupling
Cover Assembly
Downrod/
Hanger Ball Assembly
LED-Glass Assembly
Hardware Bag
Ceiling Canopy
Fan Motor
Assembly
Hand Held
Remote
Adapter-Steel Cap/Steel Cap Assembly
Blade
Set
3
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the ceiling
fan. Here are a few tips to ensure efficient product
performance.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counterclockwise direction. The airflow produced by the ceiling
fan creates a wind-chill effect, making you “feel” cooler.
Select a fan speed that provides a comfortable breeze,
lower speeds consume less energy.
Winter Season: Reverse the motor and operate the ceiling
fan at low speed in the clockwise direction. This produces
a gentle updraft, which forces warm air near the ceiling
down into the occupied space. Remember to adjust your
air conditioner when using your ceiling fan-additional energy
and dollar savings could be realized with this simple step!
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle
of the room and at least 2.1 m above the floor and 50 cm
from the walls. If ceiling height allows, install the fan
2.4-2.7 m above the floor for optimal airflow. Consult your
Fanimation Retailer for optional mounting accessories.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Electrical and Structural Requirements
This new ceiling fan will require a grounded electrical supply
line of 220-240 volts AC, 50 Hz, 10 Amp circuit. The
hanger bracket must be securely anchored and capable of
supporting a load of least 60kg. If your fan is to replace an
existing ceiling light fixture, turn electricity off at the main
fuse box at this time and remove the existing light fixture.
Figure 1 depicts a typical structural configuration that may
be used for securely mounting the fan.
Ceiling
Ceiling
Joists
Ceiling
Joists
ʆWARNING
This fan must be installed by a licensed electrician.
ʆWARNING
50 X 100 mm
Timber Batten
Between Joists
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with AS/NZS 3000 “The Wiring Rules”
and the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
Figure 1
4
Assembling This Ceiling Fan
1. Remove the hanger ball portion from the downrod/
hanger ball assembly by loosening the set screw in the
hanger ball until the ball falls freely down the downrod.
Remove the pin from the downrod, then remove the
hanger ball. Retain the pin and hanger ball for reinstallation in Step 6. (Figure 1)
Pin
Downrod
Set Screw
Hanger Ball
Figure 1
2. Remove the hairpin clip and clevis pin from the
bottom of the downrod. Retain the pin and clip for
reinstallation in Step 4. (Figure 2)
Hairpin
Clip
Clevis Pin
Figure 2
3. Loosen the two set screws in the downrod support
of the motor assembly. Route the brown, blue, green/
yellow and safety cable wires through the downrod.
(Figure 3)
Brown, Blue, Green/Yellow
and Safety Cable Wires
Downrod
Set Screws (2)
Figure 3
4. Slide downrod into the downrod support on top of
the motor. Install the clevis pin by aligning the holes
in the downrod support with holes in the downrod.
Secure clevis pin with hairpin clip. Tighten the two set
screws with nuts in the downrod support. (Figure 4)
Downrod
Hairpin Clip
Set Screws and
Locking Nuts (2)
WARNING
Clevis Pin
It is critical that the clevis pin in the downrod support
is properly installed and the set screws and nuts are
securely tightened. Failure to do so could result in
the fan falling.
Figure 4
5. Route wires through Motor Coupling Cover, Canopy
Screw Cover and Ceiling Canopy. (Figure 5)
Ceiling Canopy
Canopy Screw
Cover
Motor Coupling
Cover
Figure 5
5
Assembling This Ceiling Fan (continued)
6. Reinstall the hanger ball on the downrod as follows.
Route the three 2m length wires and safety cable through
the hanger ball. Position the pin through the two holes in the
downrod and align the hanger ball so the pin is captured
in the groove in the top of the hanger ball. Pull the hanger
ball up tight against the pin. Securely tighten the set screw
in the hanger ball. A loose set screw could create fan
wobble. (Figure 6)
Figure 6
15
-25
cm
7. Cut off excess lead wire approximately 15 - 25 cm
above top of the top of the downrod. Strip insulation off
10 mm from the end of each lead wire. (Figure 7)
NOTE: All set screws must be checked, and retightened
where necessary, before installation.
Figure 7
6
How to Hang This Ceiling Fan
WARNING
To avoid possible ſre or shock, be sure electricity is
turned off at the main fuse box before wiring.
(Figure 1)
MAIN FUSE BOX
WARNING
Figure 1
The fan must be hung with at least 2.1m of
clearance from ƀoor to blades. (Figure 2)
CEILING
1. Drill a hole in the ceiling board and batten for wiring.
Securely attach the hanger bracket to a timber batten
or other structural support using appropriate fasteners.
(Figure 3)
WARNING
NO
LESS THAN
2.1 M
FLOOR
The hanger bracket must be securely mounted and
capable of supporting at least 60 kg. If bracket and /or
timber batten are not securely attached, the fan could
wobble or fall.
Figure 2
2. Drill a ¼” pilot hole into the building structure to
prevent splitting or cracking with installation of the lag
bolt. Using the ” x 2” lag bolt and flat washer, attach
safety cable to ceiling joist or wood structural member.
The lag bolt will pass through the flat washer, safety
cable loop, and into the building structure. (Figure 3)
NOTE: Ceiling support cable must be directly secured
to ceiling joist or structural member using the ” x 2” lag
bolt and flat washer. (Figure 3)
3. Make sure the electrical supply wires, including
the hanger bracket earth wire and safety cable
are pulled through the downrod, between the hanger
bracket so that electrical connections can be made later.
3/8˝ x2 lag bolt
and flat washer
Hanger
Bracket
Timber Batten
Ceiling Support Cable
Note: Ceiling board and
wiring omitted for clarity.
Screw with hex head
wood screws(2)
Not supplied
Figure 3
4. Carefully lift the fan and seat the downrod/hanger ball
assembly on the hanger bracket that was just attached to
the timber batten or structural member. Be sure the groove
in the ball is lined up with tab on the hanger bracket.
(Figure 4)
Attach Safety Cable to
Ceiling Support Cable
Downrod/Hanger
Ball Assembly
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or re hazard.
5. Attach the safety cable to ceiling support cable. Slide
cable clamp and washer onto safety cable (from fan).
Place the end of cable through the loop of ceiling support
cable. Pull as much cable through loop as possible. Feed
end of cable into clamp hole and firmly tighten screw
(Figure 4).
Note: Ceiling board and
wiring omitted for clarity.
Figure 4
HARDWARE USED:
CEILING SUPPORT
CABLE CLAMP
W/SCREW
X
1
FLAT WASHER
Ø14 x Ø 5 x 1 mm
X
1
WARNING
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
7
How to Wire Your Ceiling Fan
This ceiling fan must be installed by a licensed electrician.
WARNING
To avoid possible ſre or shock, be sure electricity is
turned off at the main fuse box before wiring.
(Figure 1)
MAIN FUSE BOX
1. Securely connect the green/yellow earth wires from
the hanger ball and the hanger bracket and the supply
green/yellow earth wire to the terminal block as shown
in Figure 2.
Figure 1
2. Securely connect the blue fan motor wire and the
black supply neutral to the “N” terminal of the connector block as shown in Figure 2.
Supply Cable
Grn/Yel Wire
(Earth)
ʆWARNING
Black Wire
(Neutral)
Check to see that all connections are tight, including
earth, and that no bare wire is visible at the wire
connectors, except for the earth wire. Do not operate
fan until the blades are in place. Noise and motor
damage could result.
N
L1
Red Wire
(Active)
L
Terminal Block
(on Hanger Bracket)
Grn/Yel Wire
(Earth) from Hanger Bracket
3. Securely connect the brown fan motor wire and the
red (Active) supply wire to the “L” terminal of the
connector block as shown in Figure 2. After
connections have been made, carefully push leads
into the recess making sure there is separation
between connectors.
Brown Wire
(Motor Active)
Grn/Yel Wire
(Earth) from Fan
Blue Wire
(Neutral)
Hanger Ball
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
controls.
Figure 2
8
Installing The Canopy Housing
NOTE: This step is applicable after the neccessary wiring is completed.
1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed. (Figure 1)
Ceiling Canopy
WARNING
Figure 1
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and the
ceiling.
2. Securely attach and tighten the canopy screw cover
over the shoulder screws in the hanger bracket utilizing
the keyslot twist-lock feature. (Figrue 2)
Canopy Screw
Cover
Figure 2
Assembling the Ceiling Fan Blades
1. Lay flat side of blade holder on a flat surface with the
inside of the blade holder arm facing up. This is the side
with the threaded posts and pitched foot. Position the
blade over the blade holder with the threaded posts
showing. Make sure the bottom edge of the blade is fully
seated against the blade holder. Place blade cover
on top of the blade, positioning the holes over the
threaded posts. With a Phillips screwdriver, thread three
screws into the posts but do not fully tighten.Prior to final
tightening, position the centerline of the blade holder
with the center of the end of the blade. Tighten three
screws to secure the blade. (Figure 1)
CAUTION
3/16Ý-24 Pan Head
Serrated Screw (3 each per blade)
Blade Cover
Blade Holder
Blade
Figure 1
HARDWARE USED:
3/16Ŋ
Pan Head
Serrated Screw
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.
2. Secure the blade holders to the flywheel using the
1/4Ý-20 screws, the post on the blade holder need to
DOLJQWKHKROHEHWZHHQWKHÝWKUHDGHGKROHV
located on the bottom of the flywheel. (Figure 2)
NOTE: Periodically check blade holder hardware and
resecure if necessary.
!
Z
Blade Holder
WARNING
1/4Ý-20
Pan Head Screw
(2 per assembly)
To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between the rotating blades.
Figure 2
HARDWARE USED:
CAUTION
Ŋ
Pan Head
Screw
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
9
x 18
Assembling The Light Kit Assembly or Cap
1 (Option A--for use with light kit)
Remove one of the three screws in the support
bracket at the bottom of the motor assembly.
Slightly loosen the remaining two screws. Assemble
the light plate assembly to the support bracket using
the two key slots in the socket plate. Replace the third
screw and securely tighten all three screws. (Figure 1A)
1 (Option B--for use with steel cap)
Remove one of the three screws in the support
bracket at the bottom of the motor assembly.
Slightly loosen the remaining two screws. Assemble
the adapter-steel cap to the support bracket using
the two key slots in the socket plate. Replace the third
screw and securely tighten all three screws. (Figure 1B)
SCREWS (3)
Light Plate
Assembly
Figure 1A
Adapter-Steel
Cap
Figure 1B
2 (Option A--for use with light kit)
Connect the 2 single-pin connectors from the LED
assembly to the 2 single-pin connectors from motor
assembly. (Figure 2A)
NOTE: Before you connect the wire connectors, please
remove the shrinkable sleeving.
CAUTION
To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.
Shrinkable
Sleeving
2 (Option B--for use with steel cap)
If you want to install the steel cap and not the light kit.
Assemble the steel cap assembly to the adapter-steel
cap by twisting in a clockwise direction. (Figure 2B)
LED Assembly
Steel Cap
Assembly
Figure 2A
Adapter-Steel
Cap
Figure 2B
NOTE: If you have installed your fan with the steel cap,
skip steps 3 and 4.
3. Remove three screws in the light plate assembly.
Assemble the LED assembly to the light plate assembly
using the two key slots. Replace the third screw and
securely tighten all three screws. (Figure 3)
CAUTION
LED Assembly
Light Plate
Assembly
The light source is designed for this specific
application and can overheat if serviced by untrained
personnel. If any servicing is required, the product
should be returned to an authorized service facility
for examination or repair.
Figure 3
4. Secure the glass to light plate assembly by twisting
in a clockwise direction. Do not over-tighten. (Figure 4)
Light Plate
Assembly
Figure 4
10
Glass
How to Operate Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box (Figure 1).
WARNING
Check to see that all connections are tight, including
earth, and that no bare wire is visible at the wire
connectors, except for the earth wire. Do not operate
fan until the blades are in place. Noise and fan
damage could result.
MAIN FUSE BOX
Figure 1
NOTE: Receiver in controllers system features an
automatic learning function. There are no frequency
switches on the receiver unit. The receiver will
automatically scan the frequency from the hand held
control if an changes are made. the frequency settings
should be changed only in the case of interference or
if multiple ceiling fans with the same type of control
system are installed in the same structure.
2. To make the fan operational, install 23A/12V battery
(included) into the hand-held remote transmitter (If not
used for long periods of time, remove the battery to
prevent damage to the transmitter). With fan power off.
Then follow the remote code setting process. Store the
remote away from excessive heat or humidity. (Figure 2)
Figure 2
3. Remote Control Setting and Speed (RPM)
Setting Process : (Figure 3)
1. When powering on your fan, do not press any
button(s) before pressing the “SET” button,
otherwise it will fail the learn procedure. If you press
a button before the “Set” button, please turn the
power off then on again, and start the process again.
2. After installing the unit and restoring power to
your fan, press and hold the “SET” button 1~5
seconds. You must press the “SET” button within 60
seconds of restoring power to the fan.
3. The fan will start to run and begin the control
setting process.
4. DO NOT press any button(s) after pressing the SET
button and while the fan is programming or it will fail
to program. The fan will run in both directions for a
total of approximately 5 minutes.
5. When the fan stops after approximately 5 minutes
the control and speed setting process is complete.
The fan is now ready for normal use.
NOTE: If you need to change the blades: turn
the power off→ change the blades →turn the
power on →perform the control setting process
again.
11
Figure 3
How to Operate Your Ceiling Fan (continued)
4. The remote buttons function as follows: (Figure 4)
Fan speed:
I = minimum speed
II = low speed
III = medium low speed
IV = medium speed
V = medium high speed
VI = high speed
: Turns the fan off.
: Controls fan direction - forward and reverse.
: Controls light on/off button.
Figure 4
5. The receiver provides the following protective function:
Lock position: The DC motor has a built-in safety feature
against blade obstruction during operation. If something
obstructs the fan blades the motor will stop operating after
30 seconds of interruption. Please remove obstacles and
reset.
Over 80W protection: When the receiver detects motor
power consumption which is greater than 80W, the
receiver power will shutdown and fan operation will cease.
Disconnect the power supply and after 5 seconds returnpower on to the fan.
Maintenance
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should be
avoided to prevent damage to finish.
CAUTION
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of electrical shock.
Blade Cleaning
Periodic light dusting of the blades is recommended.
Avoid using water, cleansers, or harsh rags, which can
warp and ruin the blades.
12
Trouble Shooting
WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Some suggested remedies require the attention of a licensed electrician.
Trouble
Probable Cause
1. Fuse or circuit breaker blown.
1.FAN WILL
NOT START
2.FAN SOUNDS NOISY
Suggested Remedy
2. Loose power line connections to the
fan, or loose switch wire connections
in the switch housing.
1. Check main and branch circuit fuses
or circuit breakers.
2. Check line wire connections to fan
and switch wire connections in the
switch housings.
CAUTION: Make sure main power is
turned off !
3. Dead battery in remote control.
3. Replace with new battery.
1. Blades not attached to fan.
2. Loose screws in motor housing.
1. Attach blades to fan before operating.
2. Check to make sure all screws in
motor housing are snug (do not
overtighten).
3. Check to make sure the screws which
attach the fan blade holders to the
motor flywheel are tight.
3. Screws securing fan blade holders to
motor flywheel are loose.
CAUTION: Make sure main power is
turned off !
4. Motor noise caused by solid state
variable speed control.
5. Screws holding blades to blade
holders are loose.
1. Setscrew in downrod support is loose.
3.FAN WOBBLES
EXCESSIVELY
2. Setscrew in downrod/hanger ball
assembly is loose.
3. Screws securing fan blade holders to
blades are loose.
4. Blade holders not seated properly.
5. Hanger bracket and/or ceiling outlet
box is not securely fastened.
6. Fan blades out of balance.
4.NOT ENOUGH AIR
MOVEMENT
4. Some fan motors are sensitive to
signals from solid-state variable
speed controls. Solid-state controls
are not recommended, choose an
alternative control method.
5. Tighten screws securely.
1. Tighten both setscrews securely in
downrod support.
2. Tighten the setscrew in the downrod/
hanger ball assembly.
3. Check to be sure screws which attach
the fan blade holders to the blades
are tight.
4. Check to be sure the fan blade
holders seat firmly and uniformly to
the surface of the motor housing.
If holders are seated incorrectly,
loosen the screws and retighten.
5. Tighten the hanger bracket screws to
the outlet box, and secure outlet box.
6. Balance blades using balance kit
provided in hardware bag.
1. If possible, consider using a longer
downrod. Please be aware that blades
must be at least 2.1 m above floor
level.
13
Parts List
Model No. FPD8148**AU
Reference #
Description
Part #
$3'&%/
A'R1%1
3*%1
AP26%1
$33$&%1
$0$%1$8
$3%1
AP814809**
$3%1
$3%1
AP814814-220
31,
$3%1
751'
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Hanger Bracket Assembly
+DQJHU%DOO'RZQURG$VVHPEly
Canopy
Canopy Screw Cover Assembly
0otor Coupling Cover
)DQ0RWRU$VVHPEO\
Blade Cover Set
Blade Set
Blade Holder Set
/LJKW3ODWH$VVHPEO\
/('*ODVV$VVHPEO\
Adapter-Steel Cap
Steel Cap Assembly
Hand-Held Remote
15
Receiver
5&/267
16
—
/RRVH+DUGZDUH%DJ
Balance Kit
%ODGH0RXQWLQJ+DUGZDUH%DJ
Pan Head Serrated Screws
Ý
3KLOOLSV6FUHZGULYHUÝ
%ODGH+ROGHU0RXQWLQJ+DUGZare Bag:
+':)3'%1$8
—
—
—
—
—
3DQ+HDG6FUHZÝ
Bag Assembly Safety Cable
—
—
—
—
Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging materials, be certain all parts have been removed
How To Order Parts
When ordering repair parts, always
give the following information:
‡3DUW1XPEHU
‡3DUW'HVFULSWLRQ
‡)DQ0RGHO1XPEHU
For repair parts:
Phone 1300 469 326
www.myfan.com.au
14
™
The Odyn
Model FPD8148**AU Exploded-View
1
2
3
4
5
15
6
16
7
8
9
16
10
11
14
12
13
Figure 1
NOTE: The illustration shown is not to scale or its actual con¿guration may vary.
Product/parts are subject to change without notice.
15
16
MyFan Warranty for Australian purchasers
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a refund
or replacement for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount
to a major failure. All products have been imported in good faith from the overseas manufacturer.
The following warranty only covers faults due to manufacturing defects in materials or workmanship. Only orders
placed through MyFan or authorised sales partners are covered by this warranty. All ceiling fans must be installed by
a licensed electrcian.
Section 1:
1
What to do if your fan has a problem
Satisfy yourself that there is
not an installation problem.
Section 2:
2
Do NOT attempt to uninstall
or repair your fan.
3
Call 1300 469 326 for further
assistance.
MyFan 36 month on-site warranty
Congratulations! By purchasing from an Authorised Partner or directly from MyFan, your product is now covered by our 36 month
on-site warranty. Should your fan fail within the first 36 months, due to a defect in materials or workmanship, MyFan (at our sole
discretion and conditional on the limitations outlined in Section 3) will repair or replace the faulty component.
Section 3:
Limitations of warranty
After the 36 month on-site warranty period, all costs of removal and/or re-installation of the product are the sole responsibility
of the owner or their representative and not the supplier that sold the fan or MyFan.
You must have proof of your purchase to obtain any aftersales service. Keep your tax invoice or other proof of purchase together with
the installing electrician’s details. Do not uninstall or attempt to return the product to the supplier or MyFan unless advised to by MyFan.
You must be the original purchaser of the product and it must be installed in its original point of installation to be covered by this warranty.
Warranty periods begin from the date of purchase. Because of varying climate conditions, this warranty does not cover changes in finish,
including rusting, pitting, corroding, tarnishing or peeling.
The warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of heat
or humidity or as a result of any modification to the original product. Force majeure, electrical surges, lightning, power grid fluctuations,
water or by connection to alternative power supply sources (such as solar inverters) are not eligible for claims.
If electricians are engaged by MyFan to service fans that are installed in a location requiring special access equipment (such as scaffolding,
scissor lifts, etc.) the cost of providing, installing and operating the special access equipment must be born by the site owner. The need for
or use of such equipment must be stated when booking a service call.
MyFan reserves the right to charge for travelling costs incurred beyond 25km from Australian major capital cities. Travelling costs or other
expenses must be agreed to prior to a service call being booked.
Signals sent through the power grid by the electricity supplier for the control of devices may cause intermittent noise in your
product. These noises are not the result of a faulty product. Filters are available at the customer’s expense.
A certain amount of wobble is normal and should not be considered a problem or a defect.
Solid state or dimmer controls may damage your fan. Use of controllers not approved by MyFan will void your warranty.
Call
1300 469 326
Fax
(07) 3801 8575
Visit us online at www.myfan.com.au
Email
info@myfan.com.au
Mail
MyFan
PO Box 6560
GCMC QLD 9726
Distributed in Australia by MyFan Pty Ltd
Copyright 2015 Fanimation
www.myfan.com.au
2015/10 V.01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising