Model 10959-201 and -203 Wall-Mount Audio - GAI

Model 10959-201 and -203 Wall-Mount Audio - GAI
Pub.: 42004-403E
GAI-TRONICS
®
CORPORATION
A HUBBELL COMPANY
Model 10959-201 and -203
Wall-Mount Audio Messenger Interfaces
TABLE
OF
CONTENTS
Confidentiality Notice .....................................................................................................................1
Product Overview ............................................................................................................................1
Features.................................................................................................................................................... 1
Options..................................................................................................................................................... 2
Configurations......................................................................................................................................... 2
Alarms...................................................................................................................................................................2
Inputs/Outputs.......................................................................................................................................................2
Timed Events ........................................................................................................................................................2
Optional Telephone Operation..............................................................................................................................3
Page/Party® Operation ..........................................................................................................................................3
Optional ADVANCE Operation ...........................................................................................................................4
Optional Zone Operation ......................................................................................................................................4
Optional AMI Redundancy...................................................................................................................................4
Installation ......................................................................................................................................5
Mounting.................................................................................................................................................. 5
Wiring ...................................................................................................................................................... 6
Digital Outputs......................................................................................................................................................6
Digital Inputs ........................................................................................................................................................7
Audio ....................................................................................................................................................................8
System...................................................................................................................................................................8
Ethernet.................................................................................................................................................................9
Power ....................................................................................................................................................................9
Optional PBX Connection ....................................................................................................................................9
Page/Party® ...........................................................................................................................................................9
Settings and Adjustments..............................................................................................................10
Opening the Unit ................................................................................................................................... 10
Jumper Settings..................................................................................................................................... 11
600-Ohm Line Termination ................................................................................................................................11
AUDBUS1 Termination .....................................................................................................................................11
AUDBUS2 Termination .....................................................................................................................................11
Audio Contact Supervision .................................................................................................................................11
Level Adjustments ................................................................................................................................ 11
Display Brightness ..............................................................................................................................................11
Phone Line Levels ..............................................................................................................................................11
Party Line Levels ................................................................................................................................................11
Page Line Levels.................................................................................................................................................11
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 „ 800-492-1212 „ Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Table of Contents
Pub.: 42004-403E
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Date and Time Set Up........................................................................................................................... 12
Date Set Up.........................................................................................................................................................12
Time Set Up ........................................................................................................................................................12
Operation.......................................................................................................................................13
LCD Display at Initial Power Up......................................................................................................... 13
LCD Display during Operation ........................................................................................................... 14
Push-Button Operation ........................................................................................................................ 15
Stop Message ......................................................................................................................................................15
Play Message ......................................................................................................................................................15
Firmware Update ................................................................................................................................................15
Reset AMI...........................................................................................................................................................15
Return .................................................................................................................................................................15
AMI Configuration Tool (ACT) ...................................................................................................16
Overview ................................................................................................................................................ 16
System Requirements ........................................................................................................................... 16
Configurable Parameters ..................................................................................................................... 16
Fragments ...........................................................................................................................................................16
Messages.............................................................................................................................................................16
Inputs ..................................................................................................................................................................16
Output .................................................................................................................................................................17
Event Scheduling ................................................................................................................................................17
Optional Telephone Interface..............................................................................................................................17
Page/Party® Interface ..........................................................................................................................................17
Optional Zone Groups.........................................................................................................................................17
CompactFlash® ...................................................................................................................................... 18
Formatting...........................................................................................................................................................18
Card Installation..................................................................................................................................................18
Specifications ................................................................................................................................18
Replacement Parts ................................................................................................................................ 19
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
PUB. 42004-403E
GAI-TRONICS
®
CORPORATION
A HUBBELL COMPANY
Model 10959-201 and -203
Wall-Mount Audio Messenger Interfaces
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
Product Overview
The GAI-Tronics Audio Messenger Interface
(AMI) tone/speech generator broadcasts live
pages, telephone pages, pre-recorded alarm
tones, pre-recorded speech messages, etc., for
use in virtually any application.
Features
•
•
•
•
•
•
•
•
•
Recorded alarm tones
Eight inputs and eight outputs upgradeable
to 40 inputs and outputs
600-ohm, 1 Vrms audio output
CompactFlash® memory
AMI Configuration Tool (ACT) PC
Software
Scheduled events
Day/Night modes
Live/recorded speech messages
Integration to Page/Party® systems
Figure 1. Wall-Mount Audio Messenger Interface
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 „ 800-492-1212 „ Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 2 of 19
Options
•
•
•
•
•
•
Telephone access
Integration to Page/Party® systems
Up to 40 user defined inputs and 40 user defined outputs
Audio routing to eight zones
AMI redundancy for system reliability
Integration to ADVANCE systems
Table 1. Wall-Mount AMI Models and Accessories
Model
Description
10959-201
AMI, Wall-Mount with Page/Party® Interface
10959-203
AMI, Wall-Mount with Page/Party® Interface and Telephone Interface
12584-001
I/O Control Module Option
XDM002A
Desktop Paging Microphone
10960-001
Zone Interface Module
10962-00x
AMI Redundancy Controller
Configurations
Alarms
The ACT tool includes pre-recorded tones suitable for almost any application. The tones include typical
emergency tones (i.e., a siren, slow whoop, etc.) and signaling or process tones (i.e., a gong, steady tone,
etc.). All of the tones and speech messages broadcast by the AMI are stored in MP3 file format. For
applications where a required tone is not supplied, any tone recorded or stored in an MP3 file format can
be used with the AMI.
Inputs/Outputs
The AMI includes eight configurable inputs and outputs. Typically, the inputs are configured to activate
tones and/or speech messages, mute audio playback, or reset alarms. The outputs are typically used to
activate external signaling devices, interface to automated control systems or interface to paging system
equipment.
If the standard eight inputs and outputs are not sufficient for an application, an I/O Control Module can be
added to the system. The I/O control module provides an additional 32 inputs and 32 digital outputs
expanding the total I/O to 40 each.
Timed Events
The AMI has the capability to perform several functions based on the time of day. With the ACT
software, events can be scheduled to occur at any interval (hourly, daily, weekly, monthly, etc.).
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 3 of 19
Optional Telephone Operation
The Telephone Interface has multiple operational modes. The appropriate mode is configurable by the
AMI Configuration Tool software application.
The AMI can provide passcode-protected telephone access to the system. The AMI can be configured to
allow telephone access only if the correct Remote Access Security Code is entered. The remote access
code is used to prevent unwanted callers from directly accessing the system. If the system is configured
to use a security code, callers are required to enter the correct code to gain access to the system. Day and
Night modes can have different security codes.
The modes of operation are as follows:
•
Page/Party® - Delivers a live voice page (not pre-recorded) to the page line output. The party line is
held open following the page.
•
Record Page - Records a page, and delivers it to the page line output.
•
Mixed Mode - Records a page, delivers it to the page line output, and holds the party line open
following the page.
•
Live Page Mode - Delivers a live voice page (not pre-recorded) to the page line output. The party
line is not open following the page.
•
Ring Mode – Does not deliver a page, but instead plays a configured message on the page line to
signal the incoming call.
•
Manual/Disabled – The Telephone Interface does not automatically answer a phone call. However,
an input can be configured for “Manual Access” to allow an attendant to manually answer the phone,
and transfer calls to a party line.
The AMI can support two modes of operation: Day and Night Mode. The day and night modes can be
configured independently of each other.
As an example of the Day and Night modes, day mode may be configured to allow callers the ability of
paging and subsequent party line communications. The night mode may be configured to play a tone over
the paging system alerting personnel of an incoming call. In this mode, the call can be answered at any
Page/Party® station.
Page/Party® Operation
The Page/Party® operation allows for the AMI to play messages/alarms and connect phone calls to a
Page/Party® system.
The Page/Party® operation has the ability to generate the VLC tone during a message/alarm that gives
Page/Party® stations a signal to change the volume of the message/alarm being played.
When the AMI is interfaced to a Page/Party® system, the operation of the telephone interface is as
described above, and includes all page modes. The selected party line is hardwired in the system, and
cannot be changed by the caller or the AMI configuration.
In addition to the telephone operation described above, a user on the Page/Party® system can initiate a call
by using Party Hot Dial. When configured via the ACT tool, the AMI recognizes when a station goes offhook on the designated party line, and automatically dials the preprogrammed telephone number. When
the station goes on-hook, the call is terminated after the hang-up delay expires.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 4 of 19
Optional ADVANCE Operation
The Page/Party® operation allows for the AMI to play messages/alarms and connect phone calls to an
ADVANCE system.
When the AMI is interfaced to an ADVANCE system, the operation of the telephone interface is as
described above, and includes all page modes. Party lines 1 and 2 must be used in an ADVANCE
system, and cannot be changed by the caller or the AMI configuration.
Scheduled events and live pages can be played through the ADVANCE system to a specified zone group.
Zone groups are configured using the ACT tool and the ADVANCE system configuration software.
Configured zone groups can be assigned to individual events, messages, or the AMI auxiliary microphone
jack.
Optional Zone Operation
The optional Zone Interface Modules provide the capability for the AMI to route audio to eight
individually controlled zones. Each zone provides a 0 dBm/600-ohm output. Zones are assigned to zone
groups via the ACT tool. A maximum of 60 zone groups may be created. Each zone group has a unique
description, and can consist of any combination of zones. The ACT tool provides configuration of zone
groups, which can then be assigned to various events and messages. Telephone callers can use DTMF
signaling to select the zone group prior to making a page.
Optional AMI Redundancy
The optional AMI Redundant Controller (ARC) provides the capability to increase system reliability by
using two AMI units, one as the primary and one as a back up. The ARC module(s) control which AMI
is active and which is backup.
During normal alarm operation, input contacts are applied simultaneously to both the active and back-up
AMIs. The ARC module(s) allow only the active generator to play the tone/speech message over the
system speakers. The back up AMI is held in standby mode to prevent audio mixing of the two AMI
tone/speech messages.
In the event of a failure of the active AMI, the back up AMI becomes active and plays its tone/speech
message over the system speakers.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 5 of 19
Installation
Power Disconnect. The power cord is the main power disconnect for all units.
Disjontion de l’alimentation. Le cordon d’alimentation est la disjonction d’alimentation principale tous les appareils.
Para Desconectar la Alimentación: El cable de alimentación es el medio principal de desconexión del equipo.
Netzanschluß. Wenn man das Netzkabel aus der Steckdose zieht, dann ist die Spannungszuführung zum Gerät vollkommen
unterbrochen.
CAUTION
ATTENTION
de section supérieure.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Pour réduire le risque d’incendie, utiliser uniquement des conducteurs de télécommunications 26 AWG ou
PRECAUCIÓN
Para aminorar la posibilidad de incendios, utilice solamente cable de telecomunicaciones de calibre 26
(sistema AWG americano) o mayor.
VORSICHT
Um die Brandgefahr zu verringern, verwenden Sie bitte nur Fernmeldekabel der Stärke Nr. 26 AWG oder
höher.
Mounting
1. Loosen the four screws on the front cover. Open the front cover of the enclosure to the left.
2. Remove the cable connections between the front panel and rear enclosure.
3. Pull on the left side of the enclosure until the hinge pins pull loose to separate the front and rear
sections. Set the front half of the enclosure aside.
4. Determine the conduit or cable gland location on the rear enclosure. Drill spots have been provided
on top and bottom for use with either a chassis punch or hole saw. Cut or punch the appropriate size
hole(s) in the enclosure.
5. Use Myers ST-4 (1.25 inches) Scru-Tite hubs or equivalent. Reducers must be used for smaller
conduit sizes to ensure proper contact with the supplied grounding plates. The hub(s) must be
connected to the conduit before being connected to the enclosure.
6. Each mounting hole in the enclosure is 0.280 inch in diameter. Secure the rear enclosure on the wall
with screws or appropriate fasteners.
7. Route the dc power, audio, input/output control, and phone line through the conduit and into the
enclosure allowing adequate cable length to access terminal blocks.
8. Re-install the hinged front cover and re-connect the cables to the front panel.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 6 of 19
Wiring
Figure 2. Wiring Connections (Model 10959-203 shown)
Digital Outputs
Terminal block TB1, labeled DIGITAL OUTPUTS is located on the termination PCBA. It provides eight
digital common ground outputs. The outputs are open collector active low. The controlled circuit must
use the same voltage used to power the AMI. The ground or dc common terminals for the controlled
circuits must be tied to GND on the terminal block. Each output can supply 100 mA maximum current.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 7 of 19
Table 2. Digital Output Assignment
Termination
PCBA Label
Internal Terminal
Pin-Out
Function or ACT
Description
GND
TB1-1
Ground or dc common
1
TB1-2
Output 1
2
TB1-3
Output 2
3
TB1-4
Output 3
4
TB1-5
Output 4
5
TB1-6
Output 5
6
TB1-7
Output 6
7
TB1-8
Output 7
8
TB1-9
Output 8
GND
TB1-10
Ground or dc common
Digital Inputs
Terminal block TB2, labeled DIGITAL INPUTS is located on the termination PCBA. It provides eight
digital common ground inputs. The input contacts may be any combination of momentary (pulsed)
switches and maintained (latched) switches. They can be either normally open or closed dry contacts
rated at 5 mA or better. The ground or dc common terminals for the controlled circuits must be tied to
GND on the terminal block.
For the inputs to operate reliably, the cable loop resistance connecting the relay/switch contact closures
cannot exceed 200 ohms.
Table 3. Digital Input Assignment
Termination
PCBA Label
Internal Terminal
Pin-Out
Function or ACT Description
GND
TB2-1
Ground or dc common
1
TB2-2
Input 1
2
TB2-3
Input 2
3
TB2-4
Input 3
4
TB2-5
Input 4
5
TB2-6
Input 5
6
TB2-7
Input 6
7
TB2-8
Input 7
8
TB2-9
Input 8
GND
TB2-10
Ground or dc common
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 8 of 19
Audio
Terminal block TB3, labeled AUDIO is located on the termination PCBA. It provides connections for
audio inputs and outputs, and for local RS-485 data connections. Audio connections to a public address
amplifier require shielded pair conductors. Local Data connections are used with the I/O control module
and/or Zone Interface Module.
Table 4. Audio Assignment
Termination
PCBA Label
Internal
Terminal Pin-Out
600 ohm L1
TB3-1
600 ohm L2
TB3-2
AUDBUS2 L1
TB3-3
AUDBUS2 L2
TB3-4
AUDBUS1 L1
TB3-5
AUDBUS1 L2
TB3-6
PGND
TB3-7
RS485 INT GND
TB3-8
RS485 INT -
TB3-9
RS485 INT +
TB3-10
Function or ACT Description
Page output audio to public address amplifier,
ADVANCE or Zone Interface module audio
Internal audio bus and ADVANCE, ARC, or party
audio from AMI
Internal audio bus and ADVANCE party audio to
AMI
Power supply ground
Data/Gnd connection for I/O control module
System
Terminal block TB4, labeled SYSTEM is located on the termination PCBA. It provides connection for
system applications such system reboot, fault indicator and external data communications.
Table 5. System Assignment
Termination
PCBA Label
Internal
Terminal Pin-Out
Function or ACT Description
EXT DATA GND
TB4-1
No connection
EXT DATA-
TB4-2
EXT DATA+
TB4-3
Data connection for ADVANCE or external CPU
control
FLT
TB4-4
Active high signal representing a fault with AMI
REBOOT
TB4-5
Momentary active low signal to reboot AMI
GND
TB4-6
Ground reference for FLT and REBOOT.
AUD ACT 1
TB4-7
AUD ACT 2
TB4-8
Isolated SSR. Closed during AMI page.
On resistance = 30 ohms
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 9 of 19
Ethernet
The Ethernet connector, plug J1, is located on the termination PCBA, and is reserved for future
implementation.
Power
The terminal block TB6, labeled CLASS 2 12 –24 VDC is located on the termination PCBA. It provides
power connection for the AMI.
Table 6. Power Assignment
Metalwork
Label
Internal Terminal
Pin-Out
Function or ACT Description
+
TB6-1
Positive terminal of external power supply
(Black wire with white stripe from power supply)
-
TB6-2
Negative terminal of external power supply
(Solid black wire from power supply)
GND
TB6-3
Frame ground
Optional PBX Connection
The PBX connector is located on the optional telephone interface PCBA, and provides connection to a
standard PBX analog station port. It may be used as a plug-in connection or with the terminal screws
designated for tip (green) and ring (red).
Page/Party®
The connector P1 is located on the Page/Party® Interface PCBA and provides connection to a Page/Party®
system.
Table 7. Page/Party® Assignment
Metalwork
Label
Internal Terminal
Pin-Out
Party L1
P1-1
Party L2
P1-2
Page L1
P1-3
Page L2
P1-4
Function or ACT Description
The 33-ohm line interface to GAI-Tronics party line.
Internal 33-ohm termination.
The 33-ohm line interface to GAI-Tronics page line.
External 33-ohm termination required.
NOTE: Pin 1 on this connector is on the right side.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 10 of 19
Settings and Adjustments
Opening the Unit
Loosen the four screws on the front cover. Open the front cover of the enclosure to the left.
Figure 3. Model 10959-203 AMI (opened with connections and adjustments labeled).
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 11 of 19
Jumper Settings
600-Ohm Line Termination
The unit can terminate the 600-ohm line with 600 ohm for impedance matching. P5 on the termination
board in position 1-2 terminates the line to 600 ohm. P5 in position 2-3 (default) does not terminate the
line.
AUDBUS1 Termination
The unit can terminate the AUDBUS1 with 600 ohm for impedance matching. P1 on the termination
board in position 1-2 terminates the line to 600 ohm. P1 in position 2-3 (default) does not terminate the
line.
AUDBUS2 Termination
The unit can terminate the AUDBUS2 with 600 ohm for impedance matching. P6 on the termination
board in position 1-2 terminates the line to 600 ohm. P6 in position 2-3 (default) does not terminate the
line.
Audio Contact Supervision
The unit can configure the audio contact (AUD ACT) to an unsupervised or a supervised contact. P11 on
the termination board in position 1-2 configures the audio contact to be supervised for use with an
ADVANCE control cabinet. P11 in the position 2-3 (default) configures the audio contact to an isolated
SSR contact.
Level Adjustments
Display Brightness
R237 on the Main PCBA adjusts the brightness of the LCD display on the front of the assembly.
Phone Line Levels
On the optional Telephone Interface PCBA two potentiometers adjust phone audio levels. The Receiver
Volume potentiometer, R36, adjusts the volume level from the telephone line. The Transmit Volume
Potentiometer, R1, adjusts the volume to the telephone line.
Party Line Levels
On the Page/Party® Interface PCBA two potentiometers adjust party line audio levels. The Party Volume
potentiometer, R66, adjusts the volume level to the party line. The Party Sidetone Potentiometer, R30,
adjusts sidetone level from the party line.
Page Line Levels
On the Page/Party® Interface PCBA two potentiometers adjust page line audio levels. The Page Volume
potentiometer, R39, adjusts the volume level to the page line. The Page Monitor potentiometer, R69,
adjusts monitor level of audio activity from the page line.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 12 of 19
Date and Time Set Up
Date Set Up
Push buttons on the top edge of the Main PCBA of the unit allows for date set up. Complete the
following procedure to set the date. Refer to Figure 3 for the locations of the push buttons on the Main
PCBA.
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <SELECT>, PB3, to scroll to the DATE: display.
•
Press <ENTER>, PB4, to enter the DATE set up.
•
Press <ENTER>, PB4, to confirm choice.
•
Press <UP>, PB1 or <DOWN>, PB2 to select the desired day.
•
Press <SELECT>, PB3, to scroll to the month.
•
Press <UP>, PB1 or <DOWN>, PB2 to select the desired month.
•
Press <SELECT>, PB3, to scroll to the year.
•
Press <UP>, PB1 or <DOWN>, PB2 to select the desired year.
•
Press <ENTER>, PB4, to accept the DATE setting.
Time Set Up
Push buttons on the top edge of the Main PCBA of the unit allows for date set up. Complete the
following procedure to set the date.
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <SELECT>, PB3, to scroll to the TIME: display.
•
Press <ENTER>, PB4, to enter the TIME set up.
•
Press <ENTER>, PB4, to confirm choice.
•
Press <UP>, PB1 or <DOWN>, PB2 to select the desired hour.
•
Press <SELECT>, PB3, to scroll to the minute.
•
Press <UP>, PB1 or <DOWN>, PB2 to select the desired minute.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 13 of 19
Operation
Once the CompactFlash® is programmed and installed into the unit, the unit operates based on system
inputs and outputs or by manual operation.
LCD Display at Initial Power Up
At initial power up, the AMI unit completes a self-diagnostic of its settings. The LCD display cycles
through the following messages:
•
AMI firmware version
•
Boot DSP
•
Media detected
•
EEPROM firmware version
•
DSP firmware version
•
Progress bar/LOAD CONFIG
•
Configuration version
•
Configuration date and time
•
Configuration file name
•
HIO (I/O control module) board firmware version or “HIO not installed.”
•
ASM (Zone Interface Module) board firmware version or “ASM not installed.”
•
Page/Party® board firmware version
•
AMI Main board firmware version
•
Telephone Interface Mode (if telephone interface installed)
•
Telephone Interface Board firmware version or “Telephone Interface not installed.”
•
Telephone Interface Greeting file name (if recording a new greeting)
•
AMI ready
•
Time, page symbol/date
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 14 of 19
LCD Display during Operation
The LCD uses various symbols to indicate AMI activity.
•
The VU meter indicates the volume of a page playing.
MIN
MAX
•
Mute indicates the page audio is muted.
•
Progress bar indicates remaining time for the party line connection timeout.
MIN
MID
MAX
•
Telephone handset indicates the AMI unit is being accessed via a telephone connection.
•
Microphone indicates a page from the auxiliary jack.
•
Off hook indicates that a digital input designated as party line off hook is active.
•
Right/left arrows indicate transmit and receive activity on the auxiliary jack or external RS-485.
•
Text display (scrolling) displays current system status, such as the name of the current message
playing, telephone connection status, and party connection status.
•
Rotating slash, when visible, indicates the AMI has a lower priority message pending, ready to be
played.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 15 of 19
Push-Button Operation
The front panel push buttons allow for various control features including, Play a Message, Stop a
message, and Firmware Update.
Stop Message
This function halts the currently playing message. The button sequence is used:
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <ENTER>, PB4, to select the Stop: item.
•
Press <ENTER>, PB4, to confirm the selection.
Play Message
This menu item is selected to play a specific message. Messages are grouped by priority (1 through 7).
This button sequence allows the user to select a message to be played from a specific priority group:
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <SELECT>, PB3, to scroll to the Play: item.
•
Press <ENTER>, PB4, to enter the Play: item.
•
Press <SELECT>, PB3 to scroll to the message.
•
Press <ENTER>, PB4, to play the selected message.
Firmware Update
This menu item provides the means for updating the firmware of the AMI main board. This button
sequence is used:
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <SELECT>, PB3, to scroll the menu to the Firmware Update: item.
•
Press <ENTER>, PB4, to select the Firmware Update: item.
•
Press <ENTER>, PB4, to confirm the selection.
Reset AMI
•
Press <ENTER>, PB4, to enter the menu system.
•
Press <SELECT>, PB3, to scroll the menu to the System Reboot: item.
•
Press <ENTER>, PB4, to select the System Reboot: item.
•
Press <ENTER>, PB4, to confirm the selection.
Return
Selecting this menu item returns the system to normal operation mode.
•
<ENTER>, PB4, to enter the menu system
•
<SELECT>, PB3, to scroll the menu to the Return item
•
<ENTER>, PB4, to select the Return menu item and return to normal operating mode.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 16 of 19
AMI Configuration Tool (ACT)
Overview
The Audio Messenger Interface Configuration Tool (ACT) software is used to define and change
configurations for the Audio Messenger Interface (AMI), and is included with all models of AMI. To
retrieve configurations and play audio messages, the AMI accesses a CompactFlash® card. Each AMI is
shipped with a CompactFlash® card pre-programmed with the AMI Factory Default configuration.
Please refer to the online help for specific instructions.
System Requirements
The ACT software must be installed on a Windows PC (Windows 98 SE/XP/2000) equipped with a USB
port. A reader/writer capable of programming CompactFlash® memory cards must be connected to the
USB port. The CompactFlash® reader/writer is not included with the AMI.
Configurable Parameters
Fragments
All tones and voice messages are digitally recorded and stored on the CompactFlash® card as MP3 files.
Messages
Each message is a collection of fragments. The content of each message must be defined by selecting the
fragment(s) to be incorporated into the message. Other message parameters include:
• Message title
• Priority
• Volume
• Play mode and repeat interval
Inputs
Each input circuit must be enabled or disabled. If enabled, it must be programmed with several
parameters such as:
• Title containing a brief text description of the input and its use
• The type of switch contact being used to activate the input (normally open, closed)
• The action of the switch (maintained, momentary, toggle on/off)
• Function of the input (activate a message, reboot, mute, etc.)
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 17 of 19
Output
Each output circuit must be enabled or disabled. If enabled, it must be programmed with several
parameters such as:
• Title, which contains a brief text description of the output and its use
• Mode of operation when active (maintained, flash, momentary, flicker)
• Activation assignment from an input or scheduled event
Event Scheduling
Using the event-scheduling feature, messages can be set up to automatically play at certain dates and
times. When scheduling events several parameters must be set:
• Start and stop times
• Start and stop dates
• Event duration and intervals
Optional Telephone Interface
If using the telephone interface, several parameters must be set:
• The number of rings before answer
• Paging mode (live or recorded)
• Page delay, if recorded
• Maximum page duration
• Selection of a greeting message to be played to the caller
• Selection of a pre-announcement tone to be played to the PA system
Page/Party® Interface
The following parameters can be set for the Page/Party® Interface:
• VLC activation
• Party Hot Dial
Optional Zone Groups
Zone groups are configured with a unique description, and assigned any combination of the eight
available output zones.
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 18 of 19
CompactFlash®
The CompactFlash® memory card stores the system configuration, speech messages, and alarm tones.
Formatting
All new CompactFlash® memory cards must be formatted specifically for use with the AMI. Formatting
is accomplished using the following DOS-format command from Windows command prompt:
Format <drive>:/a: 16K, where <drive> is the drive letter of the PC’s CompactFlash®.
NOTE: Successful formatting of the CompactFlash® card can be performed only on Windows 2000 and
Windows XP workstations.
Card Installation
When the memory card is being installed, complete the following instructions:
Insert the memory card through the rectangular MEMORY CARD slot on the AMI main Board. Ensure
the label on the memory card faces up and slide the memory card in until it is fully seated in the slot.
When seated properly, the card protrudes approximately ¼ inch from the front of the socket.
NOTE: The memory card and its socket are keyed for proper insertion – do not force the card into the
socket.
Reboot the system so the AMI unit can read the memory card.
Specifications
Power Supply Requirements
Voltage.................................................................................12 to 24 V dc (UL listed) Class 2 power source
(plug-in 12 V dc power supply included with AMI)
Current ..................................................................................................................................1 amp minimum
Power consumed .............................................................................................................. 10 watts maximum
Audio
Speech capacity................................................................... 500 minutes with 512 Mb CompactFlash® card
Scheduled events........................................................................................................................ 29 maximum
Frequency response............................................................................ 250–6500 Hz, +0/−3 dB ref. to 1 kHz
Distortion ........................................................................................ <1% THD @ 1 kHz @ nominal settings
Outputs
600-ohm output.................................................................................................................... 1 Vrms nominal
33-ohm page output .......................................................................................................... 1.5 Vrms nominal
33-ohm party output.......................................................................................................... 1.5 Vrms nominal
Phone line output ............................................................................................................... −10 dBm nominal
Inputs
Phone line input .................................................................................................................. -10 dBm nominal
33-ohm party input............................................................................................................ 1.5 Vrms nominal
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
MODEL 10959-201 AND -203 W ALL-MOUNT AUDIO MESSENGER INTERFACES
Pub. 42004-403E
PAGE 19 of 19
Communications
ADVANCE ........................................................................................................................................ RS-485
Phone line ........................................................................................................................................... DTMF
I/O Control
Digital outputs......................................................................................................................... Open collector
Maximum output sink current.......................................................................................... 100 mA per output
Maximum output voltage................................................................................................. AMI input voltage
Isolated output............................................................. Dry contact or GAI-Tronics proprietary supervision
Digital inputs................................................................................................... Open collector or dry contact
Mechanical
Enclosure material ..................................................................High-impact, glass-reinforced polyester, gray
Mounting.......................................................................................Wall mounting; four 0.28 mounting holes
Connections........................................................................................ Four drill spots for location of conduit
Dimensions ....................................................... 13.00 H × 9.25 W × 4.00 D inches; (330 × 235 × 102 mm)
Weight.................................................................................................................................... 5 lbs. (2.27 kg)
Environmental
Temperature range ................................................................................... +32º F to +122º F (0º C to +50º C)
FCC Information
Complies with CFR47, Part 15 .......................................................................................................... Class A
Approvals
Safety of Information Technology Equipment.......UL 60950, CAN/CSA-C22.2 No. 60950-00, IEC 60950
Replacement Parts
Table 8. Replacement Parts
Model Number
Description
69517-204
Termination PCBA
69462-001
Telephone Interface PCBA
69463-001
AMI Single-Party Interface
49100-007
CompactFlash® Card (blank)
f:\standard ioms - current release\42004 instr. manuals\42004-403e.doc
03/11
Warranty
Equipment.
GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.
Services.
Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,
shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAITronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.
Warranty Periods.
Every claim by Buyer alleging a defect in the goods and/or services provided
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.
Limitations / Exclusions.
The warranties herein shall not apply to, and GAI-Tronics shall not be
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Return Policy
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.
(Rev. 10/06)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising