System Readiness Test (SRT) Drive Patterns

System Readiness Test (SRT) Drive Patterns
Cla ssific ation:
EC98-001d
Re ferenc e:
Date:
NTB98-018d
June 23, 2010
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
This bulletin has been amended. SRT drive pattern #23 on page 36 has been revised.
Please discard all previous versions of NTB98-018.
APPLIED VEHICLE(S): All 1996-97 Models As Required By State Emissions Inspections
Regulations.
SERVICE INFORMATION
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States
may require the System Readiness Test (SRT) status be checked.
• The SRT is used to indicate whether the engine control module (ECM) has completed
self diagnosis of major emissions systems and components.
• In these instances the State may require completion of the SRT before permitting the
emissions inspection to proceed.
Therefore, the State Emissions Inspection Station may advise a Nissan customer to return
to the dealership for service due to one or more SRT items coming up “INCOMPLETE.”
Use the information in this Bulletin to help you “COMPLETE” the SRT.
On 1996 and 1997 Nissan vehicles CONSULT is used to access SRT status.
• In most cases the ECM will automatically complete its self diagnosis cycle during
normal vehicle usage, and the SRT status will indicate “COMPLETE” for each
applicable system.
• Once indicating “COMPLETE,” the SRT status remains “COMPLETE” until the Self
Diagnosis memory is erased.
• Occasionally, certain portions of the self diagnostic test may not be completed as a
result of the customer’s normal driving pattern. In these cases the SRT will indicate
“INCOMPLETE” for these items.
NOTE: The SRT will also indicate “INCOMPLETE” if;
• the self diagnosis memory is erased for any reason or
• if the ECM memory power supply is interrupted for several hours.
This bulletin contains the service procedure and support information to help you;
• read SRT status and
• to perform a comprehensive road test that enables the ECM to complete the SRT.
A separate Drive Pattern sheet for each ’96 and ’97 vehicle variation is included with this
Bulletin.
NOTE: You must select the drive pattern that correctly corresponds with all variables for the
vehicle being serviced (i.e., engine, ECM part number, model, model year,
emissions certification, transmission, and powertrain).
NOTE: To ensure all ECM Self Test requirements are met, it is important to drive the entire
drive pattern even if only one SRT item indicates “INCOMPLETE.”
1/59
SERVICE PROCEDURE
SRT WORKFLOW
Vehicle Referred by IM Inspector
Start
Step 1, Page 2
Check for DTCs
**Do Not Erase**
DTC
Use Service Manual and
ASIST to repair DTCs
No DTC
Step 2, Page 4
Check SRT Status
Any "INCOMPLETE"
Step 3, Page 5
ID Vehicle
Step 4, Page 5
Check ECM Part Number
Step 5, Page 5
Perform Road Test
All "COMPLETE"
Step 6, Page 8
Recheck for DTCs
**Do Not Erase**
DTC
Use Service Manual and
ASIST to repair DTCs
No DTC
Step 7, Page 8
Confirm all SRT "COMPLETE"
All "COMPLETE"
END
2/59
NTB98-018
Step 1: Check for DTC
1. Connect CONSULT.
2. Turn ignition ON and read the program card ID on CONSULT screen (Figure 1).
• If this screen indicates a card identification other than UE991, refer to “Loading Program
Card” on page 7 of this bulletin for details.
Figure 1
Figure 2
3. If the UE991 card is loaded, Touch: Start, Engine, Self Diagnosis Results (Figure 2).
• If any Diagnostic Trouble Codes (DTCs) come up, they must be repaired at this time.
Refer to ASIST and the service manual for diagnostic information.
NOTE: Normal warranty coverage will apply to the above repairs.
• If the CONSULT screen indicates: “No Self Diagnostic Failure Indicated,” go to the
next step. Touch the “Back” key on CONSULT keypad and return to the Engine menu.
NOTE: DO NOT touch “Erase” or you will lose previously completed SRT items.
Step 2: Check SRT Status
Starting from CONSULT’s Engine menu:
1. Touch SRT-Confirmation, then touch SRT Status.
2. The screen will display the status of all SRT items for the vehicle being inspected
(Figure 3).
Figure 3
In some cases, the normal driving that occurs between the time the vehicle was referred by
the State Emissions Inspection Station and it is brought into the dealership for SRT
evaluation may allow the ECM to complete the SRT. If this occurs, no further action is
necessary on the part of the dealership. Always check SRT status before performing the
SRT drive pattern.
3/59
NTB98-018
Step 3: Identify the Vehicle
To verify the SRT status and to choose the Drive Pattern, it is extremely important to
accurately identify the model, engine, ECM part number, model year, powertrain, and
emissions certification of the vehicle.
•
•
•
Print or photocopy the Vehicle Identification Worksheet provided on page 10 of this
bulletin.
Carefully follow the instructions to completely fill out the worksheet.
Attach a copy of the completed worksheet to the hard copy of the Work Order.
Step 4: Check ECM Part Number
Use CONSULT to display the ECM part number (Figure 4).
1. From the Engine menu, touch: ECM Part Number.
Figure 4
2. Touch the blank key on CONSULT’s key pad to print the screen (Figure 4).
3. Attach the printout or write the ECM part number in the space provided on the SRT
Vehicle Identification Worksheet (page 10).
4. Touch “Back” on the CONSULT keypad to return to the Engine menu.
• Compare the ECM part number displayed by CONSULT with the list of ECM part
numbers provided in the Nissan SRT System Chart (page 11) to determine the drive
pattern for the vehicle being inspected. Write that information on the SRT Vehicle
Identification Worksheet.
• If the ECM part number displayed by CONSULT does not match a part number listed on
the SRT System Chart for that vehicle, either 1) the vehicle was identified incorrectly or
2) the vehicle has the wrong ECM installed. The SRT cannot be completed with the
incorrect ECM.
Step 5: SRT Road Test
To properly obtain an SRT reading of “COMPLETE,” it is necessary to drive the vehicle
under the exact conditions required by the vehicle’s ECM. This bulletin contains specific
driving patterns for every 1996 and 1997 Nissan vehicle. Be sure to select the correct
pattern. The SRT will not set if the wrong drive pattern for the vehicle is selected.
4/59
NTB98-018
Step 5 (continued)
1. Select the Drive Pattern based on the information from the SRT Vehicle Identification
Worksheet and the SRT System Chart:
• Use the “Bookmark” on the left side of the ASIST screen to choose the correct model
and year.
• Verify that the vehicle ECM P/N as displayed by CONSULT matches EXACTLY an
ECM P/N listed on the Drive Pattern sheet you chose.
• Print out the pattern to take with you on your test drive.
2. Prior to driving the vehicle, review the Drive Pattern and prepare to complete it from
start to finish:
• Confirm the ECM part number displayed on CONSULT for this vehicle matches with an
ECM part number on the drive pattern selected.
• Review the Pre-Check items listed on the drive pattern and ensure all conditions are
met.
• Determine the vehicle speeds required by the drive pattern.
• Plan your route to minimize traffic and traffic signals that might interrupt the Drive
Pattern tasks.
• Review the Drive Pattern section(s) that must be restarted if you are interrupted.
• Do not use the ASCD (cruise control) during any section of the Drive Pattern that
contains the “No ASCD” symbol.
• Some EVAP-equipped vehicles will require fuel be added to the tank between the first
and second trip. Be prepared to purchase fuel or plan your route to accommodate this
step.
• For these EVAP-equipped vehicles, begin road test with less than ½ tank of fuel. If
fuel level is greater than ½, more time may be required to complete EVAP sections of
the drive pattern. You also may be unable to add fuel as required.
3. Preparing to drive the vehicle:
Vehicles without OBD-II monitored EVAP System:
a. Starting with the CONSULT Engine Menu, touch: SRT Confirmation, SRT Work
Support, Main Signals. CKPS-RPM (POS), THRTL POS SEN, and B/Fuel SCHDL will
automatically be selected as monitor items. (Figure 5)
SRT Work Support Screen
Figure 5
b. Proceed to # 4, “Driving the vehicle”, on the next page.
Vehicles with OBD-II monitored EVAP System:
a. Starting with the CONSULT Engine Menu, touch: SRT Confirmation, SRT Work Support,
Main Signals.
b. If TANK F/Temp SE is not already displayed, touch the BACK key to return to the SRT
Work Support screen.
5/59
NTB98-018
Step 5 (continued)
c. Touch: Selections From Menu and select CKPS-RPM (POS), THRTL POS SEN, and
B/FUEL SCHDL if not already highlighted. Also select TANK F/TEMP SE then touch
the ENTER key.
d. Proceed to # 4, “Driving the vehicle”, below.
TIP: Monitor the Fuel Temperature if the EVAP SRT is “INCOMPLETE.” One part of the
EVAP SRT diagnostic logic requires a 3° C. increase in fuel temperature from the time the
ignition key is turned to “on” as part of the test criteria. Fluctuations in the fuel
temperature reading can extend the time required for the EVAP SRT to indicate
“COMPLETE.” If the fuel temperature change is not sufficient after completing the SRT
Drive pattern, idle the vehicle until a fuel temperature increase of at least 3° C. is noted or
until the EVAP SRT indicates “COMPLETE.”
NOTE: If the fuel temperature increases 3° C. or more but the SRT still indicates
“INCOMPLETE,” the SRT Drive Pattern may need to be repeated.
SRT Work Support Screen
Figure 6
4. Driving the vehicle:
Figure 7
IMPORTANT: Nissan requires and flat rate time allows using a driver and an assistant to
conduct SRT driving patterns. The assistant should read the drive pattern, CONSULT
data and drive time and convey driving instruction to the driver. It is the driver’s
responsibility to observe and react to traffic conditions. Always drive the vehicle in a
safe manner and obey all traffic laws.
•
•
To ensure all ECM Self Test requirements are met, drive the ENTIRE pattern whenever
any SRT items indicate “INCOMPLETE.”
Some vehicles require that sections of the Drive Pattern be driven two times to satisfy
the self diagnosis two trip logic. This requirement is called out in the Nissan SRT
System Chart and by a double line in the actual drive patterns.
For vehicles that require two trips, the pre-check engine coolant temperature must be
met before beginning Section 1 of the second trip.
5. Start the Drive Pattern test:
•
After meeting the Pre-Check conditions, start the engine and carefully follow the specific
instructions and time requirements listed in each section of the drive pattern.
TIP: The Base Fuel Schedule (B/FUEL SCHDL) is an indication of engine load. It will be
easier to match high B/FUEL SCHDL values when driving up slight hills in the
recommended gear range. It will be easier to match low B/FUEL SCHDL values when
driving down slight hills in the recommended gear range. Turning the A/C compressor ON
will increase the B/FUEL SCHDL value, while turning it OFF will decrease the value of the
B/FUEL SCHDL.
6/59
NTB98-018
Step 6: Recheck for DTC
Upon completion of the Drive Pattern determine if any DTCs have been stored.
Step 1 on page 3 for details. Only in rare cases will this occur.
•
If a DTC has been stored after completing the Drive Pattern, it must be repaired.
to ASIST and the service manual for diagnostic information.
NOTE:
•
•
Refer to
Refer
Normal warranty coverage will apply to these repairs.
Once the DTC is repaired, touch “Erase” on the CONSULT Self Diagnosis Results
screen to clear the Self Diagnosis Memory and turn ignition switch “Off” for 10 seconds.
Restart the ignition and repeat the entire Drive Pattern (Step 5) to set the SRT.
If no DTCs have been stored, DO NOT touch the “Erase” key or all SRT items will
reset to “INCOMPLETE.”
Step 7: Confirm All SRT “COMPLETE”
Refer to the procedure in Step 2 to check the SRT status using SRT-OBD Confirmation
mode.
•
If all SRT items for this vehicle as shown on the Drive Pattern sheet or Nissan SRT
System Chart indicate “COMPLETE,” the inspection is complete.
=======================================================================
CONSULT Program Card Loading Instructions
To load program card UE991 into CONSULT memory:
1. With one hand, touch and hold the upper two corners of the CONSULT screen (Figure
8a).
2. While holding the upper corners, push the “on” switch with the other hand. The two
screen corners must be held when the switch is turned “on.” If not an alarm will sound.
3. The screen should indicate: “Initialize by card” and provide an alphabet key pad (Figure
8b). If it does not, or you hear an alarm sound, push the “off” button and repeat steps
one and two.
4. Insert the program card in the card slot. Be sure the end of the card with the connector
holes faces in and the card seats fully in the slot.
5. Touch the “Y” key. The screen will begin to list a series of four letter codes. This
indicates the program is loading. It will take several minutes to load. Do not disturb
or touch any buttons while it is loading. When the program loading is complete the
screen will display “Initialization End” (Figure 8c).
Figure 8a
Figure 8b
7/59
Figure 8c
NTB98-018
6. Push the “off” button and allow CONSULT to power down.
7. Push the “on” button. CONSULT should display the new program card number on the
“START” screen. If so, the new program is ready to use. If not repeat all steps.
CLAIMS INFORMATION:
PFP: 237RE
Symptom:
HD
Diagnosis: 32
OP
CODE
FLAT RATE TIME
DESCRIPTION
A32 B14
D21
VQ GA SR KA
1996 Model Year SRT Drive Pattern DZ10AA 2.5 1.0 1.0 1.0
1997 Model Year SRT Drive Pattern DZ12AA 2.5 2.5 1.0 2.5
NOTE:
R50
VG
1.0
2.5
S14
KA
2.5
2.5
V40
VG
1.0
2.5
Z32 U13
VG KA
1.0 1.0
N/A 2.5
All flat rate times include labor for two (2) people (1 technician and 1 driver).
Additional Expenses:
DESCRIPTION
Fuel, if required, for SRT tests performed
on vehicles with EVAP system.
EXP. CODE
016
MAXIMUM AMOUNT
4 Gallons
Emission Control Warranty coverage for EFI Control Unit applies when performing SRT
Drive Pattern. Normal Warranty Coverage should be applied to any DTC-related repair.
8/59
NTB98-018
Completing the SRT Vehicle Identification Work Sheet
1. Customer Information.
• Record the appropriate information from the Work Order.
2. Vehicle Information.
Record the following information from the vehicle:
•
•
•
•
•
•
Model (Altima, Sentra, Truck, etc.).
VIN (always take the VIN directly from the vehicle ID plate). Place one letter or
number in each box.
Model Year. The 10th digit of the VIN determines the model year. T=1996, V=1997.
Engine – for 200SX and 300ZX vehicles, please specify the engine type:
⇒ 200SX – GA16 or SR20
⇒ 300ZX – Turbo or Non-turbo
Transmission type. (A/T or M/T).
Emissions Certification:
⇒ 1996 Altima models have different drive patterns for vehicles with Federal or
California emissions certification. Several States other than California require
California emissions certification.
⇒ Check the under hood emissions label on Altima to determine the emissions
certification for the vehicle being inspected (refer to Figure 9).
•
•
Figure 9
Powertrain (Trucks and Pathfinders may have either 2 Wheel Drive or 4 Wheel Drive
Powertrains).
ECM Part number. (Use CONSULT to display the ECM part number as outlined in
Step 4: Check ECM Part Number on page 4)
3. SRT Support Information.
Refer to the SRT System Chart (right half of the chart) on page 11 to determine and
record the following:
•
•
Drive Pattern Number.
SRT Check Items.
9/59
NTB98-018
SRT Vehicle Identification Worksheet
Print or make copies of this worksheet and use as needed.
Attach the completed worksheet to the Vehicle Work Order.
1. Customer Information
Customer Name:
W ork Order #
(from work order)
(from work order)
2. Vehicle Information
Model:
(check vehicle)
Must obtain VIN directly from the vehicle ID plate.
VIN:
T= 1996
V= 1997
W = 1998
Year:
(10th digit of VIN)
Engine Type:
200SX:
300ZX:
GA16
Turbo
SR20
Non-turbo
M/T
A/T
(Check vehicle and circle one.)
Transmission Type:
(Check vehicle and circle one)
Emissions Certification: ('96 Altima Only)
California
Federal
(Check under-hood emissions label for '96 Altima and circle whichever applies)
2WD
Powertrain:
4WD
(check Trucks and Pathfinders and circle applicable powertrain)
Actual ECM Part Number
(Refer to step 96-3 or 97-4)
3. SRT Support Information:
(Refer to SRT System Chart)
Drive Pattern #
Page
SRT Check Items:
(Cross out Items listed as N/A on SRT System Chart)
EGR
O2 Sensor Heater
O2 Sensor
10/59
Catalyst
EVAP System
NTB98-018
Nissan SRT System Chart (page 1)
1 trip or 2 trip SRT
Model
Altima
(Fed)
Altima
(Cal)
Altima
(Cal)
Altima
Model
Year
‘96
T/M
ECM Part No.23710-XXXXX
‘96
M/T
A/T
M/T
‘96
A/T
’97
M/T
5E400, 5E401, 5E402, 5E403, 5E404
5E410, 5E411, 5E412, 5E413, 5E414
5E500
5E501, 5E502, 5E503, 5E504
5E510
5E511, 5E512, 5E513, 5E514
5E700, 5E701, 5E702, 5E703, 5E704, 5E705,
5E720, 5E721, 5E722, 5E723, 5E724, 5E725
5E710, 5E711, 5E712, 5E713, 5E714, 5E715,
5E760, 5E761, 5E762, 5E763, 5E764, 5E765
5E800, 5E801, 5E802, 5E803, 5E804, 5E810,
5E811, 5E812, 5E813, 5E814, 5E860, 5E870
5E805, 5E806, 5E807, 5E808, 5E809, 5E815,
5E816, 5E817, 5E818, 5E819, 5E865, 5E875
54U00, 54U01, 54U02, 54U03, 54U04, 54U05,
54U06, 56U60, 56U61, 56U62, 56U63, 56U64,
56U66
54U10, 54U11, 54U12, 54U13, 54U14, 54U15,
54U16, 56U70, 56U71, 56U72, 56U73, 56U74,
56U76
0L700, 0L701, 0L702, 0L707, 0L708, 0L709,
0L760, 0L761, 0L762, 0L767, 0L768, 0L769
0L710, 0L711, 0L712, 0L717, 0L718, 0L719,
0L770, 0L771, 0L772, 0L777, 0L778, 0L779
0W000, 0W005, 0W060, 0W061, 0W063
0W010, 0W015, 0W065, 0W066, 0W067, 0W069
1W200, 1W201, 1W202, 1W203, 1W204, 1W260,
1W262
1W205, 1W206, 1W207, 1W208, 1W209, 1W265,
1W266, 1W268
1B000, 1B001, 1B002
1B010, 1B011, 1B012, 1B013, 1B014
0M220, 0M221, 0M224, 0M262, 0M263,
0M269, 0M270, 0M271, 0M272, 0M273,
0M274, 1M214, 1M217, 1M222, 1M565, 1M566
0M260, 0M261, 0M264, 0M279, 0M282, 0M283,
1M204, 1M216, 1M221, 1M520, 1M521
0M222, 0M223, 0M265, 0M266, 0M267, 0M268,
0M275, 0M276, 0M277, 0M278, 0M280, 0M284,
1M219, 1M223, 1M275, 1M575, 1M576, 1M580,
1M581
3M200, 3M202, 3M203, 3M204, 3M205, 3M206,
3M207, 3M208, 3M209, 3M260, 3M261, 3M270,
3M271, 3M300, 3M302, 3M303, 3M304, 3M305,
3M306, 3M307, 3M308, 3M309, 3M360, 3M361,
3M370, 3M371
3M210, 3M212, 3M213, 3M214, 3M215, 3M216,
3M217, 3M218, 3M219, 3M265, 3M266, 3M275,
3M276, 3M310, 3M312, 3M313, 3M314, 3M315,
3M316, 3M317, 3M318, 3M319, 3M365, 3M366,
3M375, 3M376
A/T
’97.5
M/T
A/T
Maxima
‘96
M/T
A/T
‘97
M/T
A/T
Pathfinder
‘96
‘97
M/T
A/T
M/T
A/T
Quest
Sentra-20
0SX
(GA16)
‘96
‘97
‘96
A/T
M/T
A/T
‘97
M/T
A/T
11/59
Drive
Pattern
1
2
3
4
5
6
7
EGR
O2
Sensor
1 trip
Catalyst
EVAP
1 trip
O2
Heater
N/A
1 trip
N/A
1 trip
2 trip
1 trip
2 trip
2 trip
1 trip
2 trip
1 trip
2 trip
2 trip
1 trip
2 trip
1 trip
2 trip
2 trip
1 trip
2 trip
1 trip
2 trip
2 trip
N/A
N/A
N/A
N/A
N/A
1 trip
1 trip
1 trip
1 trip
2 trip
2 trip
2 trip
2 trip
2 trip
2 trip
1 trip
1 trip
1 trip
1 trip
N/A
2 trip
2 trip
2 trip
2 trip
2 trip
19
20
21
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
N/A
N/A
N/A
22
1 trip
N/A
1 trip
1 trip
N/A
23
1 trip
1 trip
1 trip
1 trip
N/A
24
2 trip
2 trip
2 trip
2 trip
2 trip
8
9
10
11
12
13
14
15
16
17
18
25
NTB98-018
Nissan SRT System Chart (page 2)
1 trip or 2 trip SRT
Model
200SX
(SR20)
Truck
(2WD)
Model
Year
‘96/'97
'96/‘97
‘96
T/M
ECM Part No.23710-XXXXX
M/T
A/T
M/T
1M860, 1M861, 1M870, 1M871, 1M872
1M865, 1M866, 1M875, 1M876, 1M877
1S700, 1S701, 1S702, 1S703
1S300, 1S301, 1S306, 1S307, 1S704, 1S706,
1S708, 1S709, 1S717, 1S718, 1S719, 1S720,
1S721, 1S722, 1S723, 1S724
1S710, 1S712
1S302, 1S303, 1S308, 1S713, 1S714, 1S716,
1S768, 1S770, 1S771, 1S772, 1S781, 1S782
1S300, 1S301, 1S306, 1S307, 1S308, 1S704,
1S706, 1S708, 1S709, 1S717, 1S718, 1S719,
1S720, 1S721, 1S722, 1S723, 1S724,
1S302, 1S303, 1S710, 1S712, 1S713, 1S714,
1S716, 1S768, 1S770, 1S771, 1S772, 1S781,
1S782
1S760, 1S761, 1S762, 1S763
1S304, 1S305, 1S309, 1S310, 1S764, 1S766,
1S769, 1S774, 1S775, 1S776, 1S777, 1S778,
1S779, 1S780, 1S784, 1S783
1S304, 1S305, 1S309, 1S310, 1S764, 1S766,
1S769, 1S774, 1S775, 1S776, 1S777, 1S778,
1S779, 1S780, 1S783, 1S784
72F00, 72F01, 72F02, 72F03, 72F04, 72F05
72F10, 72F11, 71F12, 72F13, 72F14, 72F15
81F00, 81F01, 81F02, 81F03
81F10, 81F11, 81F12, 81F13
54P60, 54P61
54P74, 54P62
54P65, 54P66
54P75, 54P67
54P00, 54P01, 54P02, 54P03, 54P70, 54P04
54P05, 54P06, 54P07, 54P08, 54P71, 54P09
A/T
‘97
M/T
A/T
Truck
(4WD)
240SX
‘96
M/T
‘97
M/T
‘96
M/T
A/T
M/T
A/T
M/T
‘97
300ZX
(Nonturbo)
‘96
300ZX
(Turbo)
‘96
A/T
M/T
A/T
Drive
Pattern
26
27
28
29
EGR
O2
Sensor
1 trip
Catalyst
EVAP
1 trip
O2
Heater
1 trip
1 trip
N/A
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
30
31
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
32
2 trip
2 trip
2 trip
2 trip
2 trip
34
35
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
2 trip
36
2 trip
2 trip
2 trip
2 trip
2 trip
37
38
39
40
41
42
43
44
45
46
1 trip
1 trip
1 trip
1 trip
2 trip
2 trip
2 trip
2 trip
2 trip
2 trip
1 trip
2 trip
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
2 trip
1 trip
1 trip
2 trip
1 trip
2 trip
1 trip
N/A
N/A
N/A
N/A
N/A
33
Note: SRT Items highlighted in gray indicate the drive pattern section for that item must be
repeated if the trip is interrupted by releasing the throttle when not directed to do so.
No gray highlight indicates the drive pattern for that SRT item will resume at point of
interruption if the drive pattern for that SRT item is interrupted by releasing the
throttle when not directed to do so.
12/59
NTB98-018
13/59
NOTE: Select level roads whenever possible.
Read and follow all notes.
Use CONSULT in Data
Monitor to display values.
Match specifications
while driving vehicle.
Use CONSULT Data Monitor to
ensure Pre-check conditions are
met prior to starting section 1.
Increase & decrease road speed
as indicated by drive pattern lines.
Select level roads for best results.
Drive Time Requirements
Drive vehicle and meet conditions
listed for the time period indicated.
If interrupted, increase drive time
or repeat section as directed.
TRIP
Drive & Pattern sections
required for each trip.
ECM Part Number
Always check vehicle ECM
part number with CONSULT
and match to this list.
SRT Address ('96 only)
Enter this number into
CONSULT "Address
Setting" mode.
Drive Pattern Number
(referenced on system chart)
Start engine,
idle at least
1.5 minutes.
Idle
1.5 minutes
1*
O2 Sensor
Heater
ASCD
A/C switch: ON
ENG. RPM:
1,400 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.5 - 2.7 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
Drive 3 minutes
2*
EGR
ENG. RPM:
1,600 - 2,200
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at
50 - 65 MPH
Drive 1.5 minutes
3*
2nd Trip:
Turn ign. key off, add
4 gallons of fuel. Start
engine and allow to
idle 10 min. then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
*
2nd Trip
1st Trip
1st Trip:
Allow engine to idle for
10 minutes then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
4
ENGINE
COMPARTMENT
WARM-UP
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
A/C switch: ON
ENG. RPM: 1,800 - 2,100
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Drive 3 minutes
6*
NTB98-018
A/C switch
ON - adds engine load to increase B/FUEL SCHDL.
OFF - Lowers engine load to decrease B/FUEL SCHDL.
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1minute.
Selector lever:
"D" (OD OFF)
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Add fuel when directed
7*
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
Two Trip Logic
First Trip: Drive all sections 1 through 9.
Second Trip: Turn ign. off. Add 4 gallons fuel. Start engine and drive sections 4, 5, 6, 7, 8, 9.
SRT Status, Address: 1000
ECM Part Numbers: 23710-54U10, -54U11, -54U12, -54U13, -54U14, -54U15, -56U70, -56U71, -56U72, -56U73, -56U74.
System Readiness Test Drive Pattern #12
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
9*
2nd trip:
End.
1st trip:
key off
then
repeat
4 - 9.
Gear position necessary
to obtain RPM range and
B/FUEL SCHDL.
'96 Maxima A/T
Do not completely
release accelerator.
ASCD
A/C switch: OFF
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx..3,000 RPM
Idle
1 minute
EVAP SYSTEM
8*
Drive 2 minutes
SRT DRIVE PATTERN LAYOUT
Do not use ASCD
(cruise control)
Vehicle Identification
Always match vehicle and
ECM part number to correct
drive pattern sheet.
Tips to help ensure
required vehicle conditions
are met.
ASCD
Drive pattern section
number refer to notes
when shading is dark.
SRT system tested
SRT Drive Pattern Layout
14/59
Drive 3 minutes
Idle 1.5 minutes
*
B/F SCHDL: 1.5 - 1.7 msec
70˚C (158˚F)
before starting
engine.
ENG. RPM:
1,800 - 3,000
B/F SCHDL:
2.5 - 4.2 msec
A/C switch: ON
ENG. RPM: 2,100 - 2,200
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
End
'96 Altima (FED) M/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "4th"
Drive 3 minutes
Drive 3 minutes
Cruise at 50 - 60 MPH
6*
5*
Selector lever: "5th"
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "4th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and idle at
least 1.5 minutes.
2*
1*
EGR
Engine coolant
temperature
must be below
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-5E400, -5E401, -5E402, -5E403, -5E404
System Readiness Test Drive Pattern #1
Pattern #1; ‘96 Altima (FED) M/T
NTB98-018
15/59
*
Start engine and
idle at least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
ASCD
A/C switch: ON
ENG. RPM: 1,200 - 1,400
Selector lever: "D" (OD ON)
B/F SCHDL: 2.0 - 2.2 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
2*
1*
EGR
ENG. RPM:
1,800 - 3,000
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "D" (OD OFF)
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
End
'96 Altima (FED) A/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
Drive at 55 - 75 MPH
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Selector lever:
"D" (OD ON)
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-5E410, -5E411, -5E412, -5E413, -5E414
System Readiness Test Drive Pattern #2
Pattern #2; ’96 Altima (FED) A/T
NTB98-018
16/59
*
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "4th"
B/F SCHDL: 1.5 - 1.7 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
2*
EGR
1*
O2 Sensor Heater
ENG. RPM:
2,000 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
A/C switch: ON
ENG. RPM: 2,100 - 2,200
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
End
'96 Altima (CAL) M/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Selector lever: "4th"
Drive 3 minutes
5*
Drive at 55 - 75 MPH
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Selector lever: "5th"
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
32˚C (95˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-5E500
System Readiness Test Drive Pattern #3
Pattern #3; ‘96 Altima (CAL) M/T
NTB98-018
17/59
Drive 3 minutes
Idle 1.5 minutes
B/F SCHDL: 1.5 - 1.7 msec
70˚C (158˚F)
before starting
engine.
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "4th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and idle at
least 1.5 minutes.
2
EGR
1
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ECM Part Numbers: 23710-5E501, -5E502, -5E503, -5E504
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
A/C switch: ON
ENG. RPM: 2,100 - 2,200
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'96 Altima (CAL) M/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Selector lever: "4th"
Selector lever:
"5th"
Drive 3 minutes
Drive 3 minutes
Steady state cruise at: 53 - 58 MPH
6
O2 SENSOR
5
CATALYST
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
4
KEY "OFF"
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
System Readiness Test Drive Pattern #4
Pattern #4; ‘96 Altima (CAL) M/T
NTB98-018
18/59
*
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
ASCD
A/C switch: ON
ENG. RPM: 1,200 - 1,400
Selector lever: "D" (OD ON)
B/F SCHDL: 2.0 - 2.2 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
2*
EGR
1*
O2 Sensor Heater
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "D" (OD OFF)
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
End
'96 Altima (CAL) A/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
Drive at 55 - 75 MPH
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Selector lever:
"D" (OD ON)
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
32˚C (95˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-5E510
System Readiness Test Drive Pattern #5
Pattern #5; ‘96 Altima (CAL) A/T
NTB98-018
Drive 3 minutes
Idle 1.5 minutes
19/59
B/F SCHDL: 2.0 - 2.2 msec
70˚C (158˚F)
before starting
engine.
ASCD
A/C switch: ON
ENG. RPM: 1,200 - 1,400
Selector lever: "D" (OD ON)
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and idle at
least 1.5 minutes.
2
EGR
1
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ECM Part Numbers: 23710-5E511, -5E512, -5E513, -5E514
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "D" (OD OFF)
Selector lever:
"D" (OD ON)
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6
O2 SENSOR
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'96 Altima (CAL) A/T
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
5
4
Drive 3 minutes
CATALYST
KEY "OFF"
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
System Readiness Test Drive Pattern #6
Pattern #6; ‘96 Altima (CAL) A/T
NTB98-018
20/59
Drive 3 minutes
Idle 1.5 minutes
B/F SCHDL: 1.5 - 1.7 msec
70˚C (158˚F)
before starting
engine.
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "4th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and idle at
least 1.5 minutes.
2
EGR
1
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ENG. RPM:
1,800 - 2,800
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "4th"
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "5th"
Drive 3 minutes
Drive 3 minutes
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'97 Altima M/T
A/C switch: ON
ENG. RPM: 2,100 - 2,200
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
6
O2 SENSOR
5
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
KEY "OFF"
ECM Part Numbers: 23710-5E700, -5E701, -5E702, -5E703, -5E704, -5E705, -5E720, -5E721, -5E722, -5E723, -5E724, -5E725
System Readiness Test Drive Pattern #7
Pattern #7; ’97 Altima M/T
NTB98-018
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
21/59
ASCD
A/C switch: ON
ENG. RPM: 1,200 - 1,400
Selector lever: "D" (OD ON)
B/F SCHDL: 2.0 - 2.2 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor Heater
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "D" (OD OFF)
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever:
"D" (OD ON)
Drive 3 minutes
5
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
KEY "OFF"
ECM Part Numbers: 23710-5E710, -5E711, -5E712, -5E713, -5E714, -5E715, -5E760, -5E761, -5E762, -5E763, -5E764, -5E765
System Readiness Test Drive Pattern #8
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'97 Altima A/T
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6
O2 SENSOR
Pattern #8; ’97 Altima A/T
NTB98-018
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
22/59
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "4th"
B/F SCHDL: 1.5 - 1.7 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor Heater
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ENG. RPM:
1,800 - 2,800
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "4th"
B/F SCHDL:
2.5 - 4.2 msec
Selector lever: "5th"
Drive 3 minutes
5
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
KEY "OFF"
ECM Part Numbers: 23710-5E800, -5E801, -5E802, -5E803, -5E804, -5E810, -5E811, -5E812, -5E813, -5E814, -5E860, -5E870
System Readiness Test Drive Pattern #9
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'97.5 Altima M/T
A/C switch: ON
ENG. RPM: 2,100 - 2,200
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6
O2 SENSOR
Pattern #9; ’97.5 Altima M/T
NTB98-018
Drive 3 minutes
Idle 1.5 minutes
23/59
B/F SCHDL: 2.0 - 2.2 msec
70˚C (158˚F)
before starting
engine.
ASCD
A/C switch: ON
ENG. RPM: 1,200 - 1,400
Selector lever: "D" (OD ON)
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and idle at
least 1.5 minutes.
2
EGR
1
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.5 - 4.2 msec
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "D" (OD OFF)
Selector lever:
"D" (OD ON)
Drive 3 minutes
5
Cruise at 50 - 60 MPH
IGN switch "OFF"
10 seconds
(Not more than 5 minutes)
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
KEY "OFF"
ECM Part Numbers: 23710-5E805, -5E806, -5E807, -5E808, -5E809, -5E815, -5E816, -5E817, -5E818, -5E819, 5E865, -5E875
System Readiness Test Drive Pattern #10
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'97.5 Altima A/T
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6
O2 SENSOR
Pattern #10; ’97.5 Altima A/T
NTB98-018
24/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,000 - 1,400
Selector lever: "5th"
B/F SCHDL: 1.8 - 3.0 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR
1*
O2 Sensor
Heater
ENG. RPM:
1,800 - 2,400
Selector lever:
"5th"
B/F SCHDL:
2.3 - 3.7 msec
Drive at
50 - 65 MPH
Drive 1.5 minutes
3*
2nd Trip:
Turn ign. key off, add
4 gallons of fuel. Start
engine and allow to
idle 10 min. then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
*
2nd Trip
1st Trip
1st Trip:
Allow engine to idle for
10 minutes then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
4
ENGINE
COMPARTMENT
WARM-UP
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
7*
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
Two Trip Logic
First Trip: Drive all sections 1 through 9.
Second Trip: Turn ign. off. Add 4 gallons fuel. Start engine and drive sections 4, 5, 6, 7, 8, 9.
ECM Part Numbers: 23710-54U00, -54U01, -54U02, -54U03, -54U04, -54U05, -54U06, -56U60, -56U61, -56U62, -56U63, -56U64, -56U66
System Readiness Test Drive Pattern #11
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
9*
2nd trip:
End.
1st trip:
key off
then
repeat
4 - 9.
'96 Maxima M/T
Do not completely
release accelerator.
ASCD
A/C switch: OFF
Accelerate to 47 MPH
Decelerate to 41 MPH
Accelerate to 47 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
8*
EVAP SYSTEM
Pattern #11; ‘96 Maxima M/T
NTB98-018
25/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,400 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.5 - 2.7 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR
1*
O2 Sensor
Heater
ENG. RPM:
1,600 - 2,200
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at
50 - 65 MPH
Drive 1.5 minutes
3*
2nd Trip:
Turn ign. key off, add
4 gallons of fuel. Start
engine and allow to
idle 10 min. then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
*
2nd Trip
1st Trip
1st Trip:
Allow engine to idle for
10 minutes then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
4
ENGINE
COMPARTMENT
WARM-UP
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
A/C switch: ON
ENG. RPM: 1,800 - 2,100
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
7*
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
Two Trip Logic
First Trip: Drive all sections 1 through 9.
Second Trip: Turn ign. off. Add 4 gallons fuel. Start engine and drive sections 4, 5, 6, 7, 8, 9.
ECM Part Numbers: 23710-54U10, -54U11, -54U12, -54U13, -54U14, -54U15, -54U16, -56U70, -56U71, -56U72, -56U73, -56U74, -56U76
System Readiness Test Drive Pattern #12
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
9*
2nd trip:
End.
1st trip:
key off
then
repeat
4 - 9.
'96 Maxima A/T
Do not completely
release accelerator.
ASCD
A/C switch: OFF
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
8*
EVAP SYSTEM
Pattern #12; ‘96 Maxima A/T
NTB98-018
26/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,000 - 1,400
Selector lever: "5th"
B/F SCHDL: 1.8 - 3.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 2,400
Selector lever:
"5th"
B/F SCHDL:
2.3 - 3.7 msec
Drive at:
50 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-0L700, -0L701, -0L702, -0L707, -0L708, -0L709, -0L760, -0L761, -0L762, -0L767, -0L768, -0L769
System Readiness Test Drive Pattern #13
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Maxima M/T
ASCD
A/C switch: OFF
Do not completely
release accelerator.
A/C switch: OFF
Accelerate to 47 MPH
Decelerate to 41 MPH
Accelerate to 47 MPH
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
Selector lever:
"4th"
Idle
1 minute
8*
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #13; ‘97 Maxima M/T
NTB98-018
27/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,400 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.5 - 2.7 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,600 - 2,200
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at:
50 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 1,800 - 2,100
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
ECM Part Numbers: 23710-0L710, -0L711, -0L712, -0L717, -0L718, -0L719, -0L770, -0L771, -0L772, -0L777, -0L778, -0L779
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
System Readiness Test Drive Pattern #14
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Maxima A/T
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #14; ‘97 Maxima A/T
NTB98-018
28/59
Drive 3 minutes
Idle 1.5 minutes
*
B/F SCHDL: 2.5 - 3.0 msec
32˚C (95˚F)
before starting
engine.
ENG. RPM:
1,800 - 2,600
B/F SCHDL:
2.5 - 4.5 msec
Selector lever: "4th"
Do not decelerate for more than
3 consecutive seconds.
A/C switch: ON
ENG. RPM: 2,300 - 2,500
B/F SCHDL: More than 2.3 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
O2 SENSOR
End
'96 Pathfinder M/T
Keep engine speed above 3,000RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Selector lever:
"5th"
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
Drive 3 minutes
5*
4
Drive at 41 - 59 MPH
Drive 1.5 minutes
3*
CATALYST
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 2,000
Selector lever: "5th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and
idle at least 1.5 minutes.
2*
EGR
1*
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-0W000, -0W005, -0W060, -0W061, -0W063
System Readiness Test Drive Pattern #15
Pattern #15; ‘96 Pathfinder M/T
NTB98-018
Drive 3 minutes
Idle 1.5 minutes
29/59
*
engine.
ASCD
A/C switch: ON
ENG. RPM: 1,500 - 1,800
ENG. RPM:
1,600 - 2,400
B/F SCHDL:
2.5 - 4.5 msec
Selector lever:
"D" (OD ON)
Drive at 44 - 63 MPH
Drive 1.5 minutes
3*
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
5*
4
Do not decelerate for more than
3 consecutive seconds.
A/C switch: ON
ENG. RPM: 1,900 - 2,200
B/F SCHDL: More than 2.8 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
O2 SENSOR
End
'96 Pathfinder A/T
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
CATALYST
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
before starting
Selector lever: "D" (OD ON)
B/F SCHDL: 2.8 - 3.5 msec
32˚C (95˚F)
must be below
temperature
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and
idle at least 1.5 minutes.
2*
EGR
1*
O2 Sensor Heater
Engine coolant
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-0W010, -0W015, -0W065, -0W066, -0W067, -0W069
System Readiness Test Drive Pattern #16
Pattern #16; ’96 Pathfinder A/T
NTB98-018
30/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,600 - 2,000
Selector lever: "5th"
B/F SCHDL: 2.5 - 3.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 2,600
Selector lever:
"5th"
B/F SCHDL:
2.5 - 4.5 msec
Drive at:
41 - 59 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,300 - 2,500
Selector lever: "5th"
B/F SCHDL:
More than 2.3 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Accelerate to 44 MPH
Decelerate to 38 MPH
Accelerate to 44 MPH
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
Selector lever:
"4th"
Idle
1 minute
8*
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Pathfinder M/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1W200, -1W201, -1W202, -1W203, -1W204, -1W260, -1W262
System Readiness Test Drive Pattern #17
Pattern #17; ‘97 Pathfinder M/T
NTB98-018
31/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,500 - 1,800
Selector lever: "D" (OD ON)
B/F SCHDL: 2.8 - 3.5 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,600 - 2,400
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at:
44 - 63 MPH
Drive 1.5 minutes
3
*
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 1,800 - 2,200
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 2.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 38 MPH
Decelerate to 31 MPH
Accelerate to 38 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
EVAP SYSTEM
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Pathfinder A/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5,6,7,8.
ECM Part Numbers: 23710-1W205, -1W206, -1W207, -1W208, -1W209, -1W265, -1W266, -1W268
System Readiness Test Drive Pattern #18
Pattern #18; ’97 Pathfinder A/T
NTB98-018
32/59
Drive 3 minutes
Idle 1.5 minutes
*
B/F SCHDL: 3.2 - 3.8 msec
32˚C (95˚F)
before starting
engine.
ENG. RPM:
1,600 - 2,800
B/F SCHDL:
2.5 - 4.0 msec
Do not decelerate for more than
3 consecutive seconds.
End
'96 Quest A/T
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 2.0 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Steady state cruise at: 53 - 58 MPH
Selector lever: "D" (OD OFF)
Drive 3 minutes
Drive 3 minutes
Cruise at 50 - 60 MPH
6*
5*
O2 SENSOR
Selector lever:
"D" (OD ON)
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Drive at 55 - 75 MPH
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 1,800
Selector lever: "D" (OD ON)
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
Start engine and
idle at least 1.5 minutes.
2*
EGR
1*
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-1B000, -1B001, -1B002
System Readiness Test Drive Pattern #19
Pattern #19; ’96 Quest A/T
NTB98-018
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
33/59
ASCD
A/C switch: ON
ENG. RPM: 1,600 - 1,800
Selector lever: "D" (OD ON)
B/F SCHDL: 3.2 - 3.8 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor Heater
Two Trip Logic (all sections)
1st Trip: Drive 1 through 6, then turn ign. off and allow engine to cool to 158˚F.
2nd Trip: Drive sections 1 through 6 again.
ECM Part Numbers: 23710-1B010, -1B011, -1B012, -1B013, -1B014
ENG. RPM:
1,600 - 2,800
B/F SCHDL:
2.5 - 4.0 msec
Selector lever: "D" (OD OFF)
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever:
"D" (OD ON)
Drive 3 minutes
5
CATALYST
Cruise at 50 - 60 MPH
Then cycle ignition switch
OFF for 10 seconds.
Restart engine and
immediately begin next
drive pattern section.
Allow engine to idle for at
least 10 minutes.
4
ENGINE COMPARTMENT
WARM-UP
Drive at 55 - 75 MPH
Drive 1.5 minutes
3
System Readiness Test Drive Pattern #20
2nd Trip:
End
1st Trip:
Key off then
repeat 1 to 6
'97 Quest A/T
A/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 2.0 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6
O2 SENSOR
Pattern #20; ‘97 Quest A/T
NTB98-018
34/59
Drive 3 minutes
Idle 1.5 minutes
*
B/F SCHDL: 1.8 - 2.0 msec
70˚C (158˚F)
before starting
engine.
ENG. RPM:
1,900 - 3,000
B/F SCHDL:
2.5 - 3.7 msec
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Selector lever: "4th"
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Selector lever:
"4th"
Downshift
then decel.
7*
End
'96 Sentra/200SX (GA16DE) M/T
A/C switch: ON
ENG. RPM: 2,200 - 2,400
B/F SCHDL: More than 1.8 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
Drive 3 minutes
Cruise at 50 - 60 MPH
6*
O2 SENSOR
5*
Selector lever: "5th"
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Drive at 55 - 70 MPH
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: ON
ENG. RPM: 2,500 - 2,700
Selector lever: "4th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
Start engine and idle at
least 1.5 minutes.
2*
EGR
1*
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-0M220, -0M221, -0M224, -0M262, -0M263, -0M269, -0M270, -0M271, -0M272, -0M273, -0M274, -1M214, -1M217, 1M222, -1M565, -1M566
System Readiness Test Drive Pattern #21
Pattern #21; ‘96 Sentra/200SX (GA16DE) M/T
NTB98-018
35/59
Start engine and idle at
least 1.5 minutes.
*
B/F SCHDL: 1.8 - 2.0 msec
70˚C (158˚F)
before starting
engine.
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
B/F SCHDL:
2.5 - 3.7 msec
ENG. RPM:
1,900 - 3,000
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Selector lever: "4th"
Selector lever: "5th"
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Selector lever:
"4th"
Downshift
then decel.
7*
End
'96 Sentra/200SX (GA16DE) M/T
A/C switch: ON
ENG. RPM: 2,200 - 2,400
B/F SCHDL: More than 1.8 msec
Selector lever: "5th"
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
Drive 3 minutes
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: ON
ENG. RPM: 2,500 - 2,700
Selector lever: "4th"
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
6*
O2 SENSOR
5*
CATALYST
Cruise at 50 - 60 MPH
Drive 1.5 minutes
Drive 3 minutes
Idle 1.5 minutes
4
ENGINE COMPARTMENT
WARM-UP
Drive at 55 - 70 MPH
3*
2*
EGR
1*
O2 Sensor Heater
Engine coolant
temperature
must be below
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-0M260, -0M261, -0M264, -0M279, -0M282, -0M283, -1M204, -1M216, -1M221, -1M520, -1M521
System Readiness Test Drive Pattern #22
Pattern #22; ‘96 Sentra/200SX (GA16DE) M/T
NTB98-018
Pattern #23; ‘96 Sentra/200SX (GA16DE) A/T
36/59
NTB98-018
37/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
2,500 - 2,700
Selector lever: "4th"
B/F SCHDL: 1.8 - 2.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,900 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.5 - 3.7 msec
Drive at:
55 - 70 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,200 - 2,400
Selector lever: "5th"
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 44 MPH
Decelerate to 38 MPH
Accelerate to 44 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
Idle
1 minute
EVAP SYSTEM
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Sentra/200SX (GA16DE) M/T
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
temperature
must be below
Engine coolant
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-3M200, -3M202, -3M203, -3M204, -3M205, -3M206, -3M207, -3M208, -3M209, -3M260, -3M261, -3M270, -3M271,
-3M300, -3M302, -3M303, -3M304, -3M305, -3M306, -3M307, -3M308, -3M309, -3M360, -3M361, -3M370, -3M371
System Readiness Test Drive Pattern #24
Pattern #24; ‘97 Sentra/200SX (GA16DE) M/T
NTB98-018
38/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,700 - 1,900
Selector lever: "D" (OD ON)
B/F SCHDL: 2.5 - 2.8 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
2,000 - 3,000
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.0 - 3.7 msec
Drive at:
55 - 75 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,200 - 2,300
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
NTB98-018
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 34 MPH
Decelerate to 28 MPH
Accelerate to 34 MPH
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
B/F SCHDL:
Less than 2.0 msec
Drive 2 minutes
Steady state cruise at
31 - 44 MPH
Idle
1 minute
8*
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Sentra/200SX (GA16DE) A/T
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
Engine coolant
temperature
must be below
Pre-check
ECM Part Numbers: 23710-3M210, -3M212, -3M213, -3M214, -3M215, -3M216, -3M217, -3M218, -3M219, -3M265, -3M266, -3M275, -3M276,
-3M310, -3M312, -3M313, -3M314, -3M315, -3M316, -3M317, -3M318, -3M319, -3M365, -3M366, -3M375, -3M376
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
System Readiness Test Drive Pattern #25
Pattern #25; ‘97 Sentra/200SX (GA16DE) A/T
39/59
*
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
ASCD
A/C switch: ON
ENG. RPM: 1,800 - 2,200
Selector lever: "5th"
B/F SCHDL: 1.5 - 1.7 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
2*
EGR
1*
O2 Sensor Heater
ENG. RPM:
2,000 - 2,800
B/F SCHDL:
2.0 - 3.0 msec
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Selector lever: "4th"
Drive 3 minutes
5*
Drive at 50 - 59 MPH
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Selector lever: "5th"
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
A/C switch: ON
ENG. RPM: 2,500 - 2,700
B/F SCHDL: More than 1.5 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
End
'96-'97 200SX (SR20DE) M/T
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-1M860, 1M861, -1M870, -1M871, -1M872
System Readiness Test Drive Pattern #26
Pattern #26; ‘96-97 200SX (SR20DE) M/T
NTB98-018
40/59
*
Start engine and idle at
least 1.5 minutes.
Drive 3 minutes
Idle 1.5 minutes
ASCD
A/C switch: ON
ENG. RPM: 1,300 - 1,500
Selector lever: "D" (OD ON)
B/F SCHDL: 2.3 - 2.5 msec
Hold recommended B/F SCHDL
range. Allow road speed to vary
as necessary
2*
EGR
1*
O2 Sensor Heater
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
2.0 - 3.5 msec
Selector lever: "D" (OD OFF)
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
Drive at 50 - 70 MPH
Then cycle ignition switch OFF
for 10 seconds. Restart engine
and immediately begin next
drive pattern section.
Allow engine to idle for at least
10 minutes.
4
CATALYST
Selector lever:
"D" (OD ON)
Drive 1.5 minutes
3*
ENGINE COMPARTMENT
WARM-UP
A/C switch: ON
ENG. RPM: 2,100 - 2,300
B/F SCHDL: More than 1.5 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
6*
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute
in neutral or park.
Idle
1 minute
7*
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
End
'96-'97 200SX (SR20DE) A/T
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-1M865, -1M866, -1M875, -1M876, -1M877
System Readiness Test Drive Pattern #27
Pattern #27; ‘96-‘97 200SX (SR20DE) A/T
NTB98-018
41/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "4th"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR SYSTEM
1*
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at
55 - 65 MPH
Drive 1.5 minutes
3*
*
then cycle ignition switch
OFF for 10 seconds.
Restart engine and
immediately begin next
drive pattern section.
Allow engine to idle for
at least 10 minutes
4
ENGINE
COMPARTMENT
WARM-UP
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "4th"
A/C switch: ON
ENG. RPM: 2,300 - 2,500
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at 53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all section one time.
ECM Part Numbers: 23710-1S700, -1S701, -1S702, -1S703
System Readiness Test Drive Pattern #28
ASCD
End.
'96 Truck (2WD) M/T
A/C switch: OFF
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
ASCD
Idle
1 minute
in park or
neutral.
Idle
1 minute
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 44 MPH
Decelerate to 38 MPH
Accelerate to 44 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #28; ‘96 Truck (2WD) M/T
NTB98-018
42/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "4th" or "5th"
B/F SCHDL: 1.5 - 3.2 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
Idle
1.5 minutes
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at:
55 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,300 - 2,500
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 44 MPH
Decelerate to 38 MPH
Accelerate to 44 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
EVAP SYSTEM
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'96 Truck (2WD) M/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
second trip.
engine for either
the first or
must be below
70˚C (158˚F)
before starting
Engine coolant
temperature
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S300, -1S301, -1S306, -1S307, -1S704, -1S706, -1S708, -1S709, -1S717, -1S718, -1S719, -1S720, -1S721, -1S722, -1S723, -1S724
System Readiness Test Drive Pattern #29
Pattern #29; ‘96 Truck (2WD) M/T
NTB98-018
43/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,200 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.3 - 2.8 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR SYSTEM
1*
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.2 msec
Drive at
55 - 75 MPH
Drive 1.5 minutes
3*
*
then cycle ignition switch
OFF for 10 seconds.
Restart engine and
immediately begin next
drive pattern section.
Allow engine to idle for
at least 10 minutes
4
ENGINE
COMPARTMENT
WARM-UP
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "D" (OD OFF)
A/C switch: ON
ENG. RPM: 2,000 - 2,200
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.5 msec
Steady state cruise at 53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all section one time.
ECM Part Numbers: 23710-1S710, -1S712
System Readiness Test Drive Pattern #30
Idle
1 minute
in park or
neutral.
Idle
1 minute
ASCD
A/C switch: OFF
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
End.
'96 Truck (2WD) A/T
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 38 MPH
Decelerate to 31 MPH
Accelerate to 38 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #30; ’96 Truck (2WD) A/T
NTB98-018
44/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,200 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.3 - 2.8 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.2 msec
Drive at:
55 - 75 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,000 - 2,200
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 38 MPH
Decelerate to 31 MPH
Accelerate to 38 MPH
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
B/F SCHDL:
Less than 2.0 msec
Drive 2 minutes
8*
Steady state cruise at
31 - 44 MPH
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'96 Truck (2WD) A/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S302, -1S303, -1S308, -1S713, -1S714, -1S716, -1S768, -1S770, -1S771, -1S772, -1S781, -1S782
System Readiness Test Drive Pattern #31
Pattern #31; ’96 Truck (2WD) A/T
NTB98-018
45/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "4th" or "5th"
B/F SCHDL: 1.5 - 3.2 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
Idle
1.5 minutes
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at:
55 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,300 - 2,500
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
ASCD
A/C switch: OFF
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Accelerate to 44 MPH
Decelerate to 38 MPH
Accelerate to 44 MPH
Do not completely
release accelerator.
Selector lever:
"4th"
B/F SCHDL:
Less than 2.0 msec
Drive 2 minutes
Steady state cruise at
31 - 44 MPH
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
8*
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Truck (2WD) M/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S300, -1S301, -1S306, -1S307, -1S704, -1S706, -1S708, -1S709, -1S717, -1S718, -1S719, -1S720, -1S721, -1S722, -1S723, 1S724
System Readiness Test Drive Pattern #32
Pattern #32; ’97 Truck (2WD) M/T
NTB98-018
46/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,200 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 2.3 - 2.8 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
Idle
1.5 minutes
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 3,000
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.2 msec
Drive at:
55 - 75 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,000 - 2,200
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 38 MPH
Decelerate to 31 MPH
Accelerate to 38 MPH
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
B/F SCHDL:
Less than 2.0 msec
Drive 2 minutes
8*
Steady state cruise at
31 - 44 MPH
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Truck (2WD) A/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
second trip.
70˚C (158˚F)
before starting
engine for either
the first or
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S302, -1S303, -1S308, -1S710, -1S712, -1S713, -1S714, -1S716, -1S768, -1S770, -1S771, -1S772, -1S781, -1S782
System Readiness Test Drive Pattern #33
Pattern #33; ‘97 Truck (2WD) A/T
NTB98-018
47/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "3rd"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
Idle
1.5 minutes
EGR SYSTEM
1*
O2 Sensor
Heater
ENG. RPM:
2,200 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at
50 - 60 MPH
Drive 1.5 minutes
3*
*
then cycle ignition switch
OFF for 10 seconds.
Restart engine and
immediately begin next
drive pattern section.
Allow engine to idle for
at least 10 minutes
4
ENGINE
COMPARTMENT
WARM-UP
Drive 3 minutes
5*
CATALYST
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "4th"
Cruise at 50 - 60 MPH
ASCD may be used
A/C switch: ON
ENG. RPM: 2,400 - 2,600
Selector lever: "5th"
B/F SCHDL:
More than 1.8 msec
Steady state cruise at 53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
engine.
70˚C (158˚F)
before starting
temperature
must be below
Engine coolant
Pre-check
One Trip Logic for all sections.
Drive all section one time.
ECM Part Numbers: 23710-1S760, -1S761, -1S762, -1S763
System Readiness Test Drive Pattern #34
Idle
1 minute
in park or
neutral.
Idle
1 minute
ASCD
A/C switch: OFF
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
End.
'96 Truck (4WD) M/T
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #34; ’96 Truck (4WD) M/T
NTB98-018
48/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "3rd"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
Idle
1.5 minutes
EGR
1
O2 Sensor
Heater
ENG. RPM:
2,200 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at:
55 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,400 - 2,600
Selector lever: "5th"
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
EVAP SYSTEM
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'96 Truck (4WD) M/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S304, -1S305, -1S309, -1S310, -1S764, -1S766, -1S769, -1S774, -1S775, -1S776, -1S777, -1S778, -1S779, -1S780, -1S783, -1S784
System Readiness Test Drive Pattern #35
Pattern #35; ‘96 Truck (4WD) M/T
NTB98-018
49/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,800 - 2,200
Selector lever: "3rd"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
2,200 - 3,000
Selector lever:
"5th"
B/F SCHDL:
2.0 - 3.2 msec
Drive at:
55 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,400 - 2,600
Selector lever: "5th"
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
ASCD
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
Idle
1 minute
in Park or
Neutral.
Idle
1 minute
EVAP SYSTEM
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 Truck (4WD) M/T
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-1S304, -1S305, -1S309, -1S310, -1S764, -1S766, -1S769, -1S774, -1S775, -1S776, -1S777, -1S778, -1S779, -1S780, -1S783, -1S784
System Readiness Test Drive Pattern #36
Pattern #36; ’97 Truck (4WD) M/T
NTB98-018
50/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
2,000 - 2,200
Selector lever: "4th"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR
1*
O2 Sensor
Heater
ENG. RPM:
1,800 - 2,800
Selector lever:
"5th"
B/F SCHDL:
2.5 - 4.0 msec
Drive at
55 - 65 MPH
Drive 1.5 minutes
3*
2nd Trip:
Turn ign. key off, add
4 gallons of fuel. Start
engine and allow to
idle 10 min. then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
*
2nd Trip
1st Trip
1st Trip:
Allow engine to idle for
10 minutes then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
4
ENGINE
COMPARTMENT
WARM-UP
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
Selector lever:
"4th"
Downshift
then decel.
7*
Idle
1 minute
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "5th"
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Downshift then completely
release accelerator more
than
5 seconds without
B/F SCHDL:
braking, then idle 1minute.
More than 1.5 msec
Drive 3 minutes
6*
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
second trip.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
Pre-check
Two Trip Logic
First Trip: Drive all sections 1 through 9.
Second Trip: Turn ign. off. Add 4 gallons fuel. Start engine and drive sections 4, 5, 6, 7, 8, 9.
ECM Part Numbers: 23710-72F00, -72F01, -72F02, -72F03, -72F04, -72F05
System Readiness Test Drive Pattern #37
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
9*
2nd trip:
End.
1st trip:
key off
then
repeat
4 - 9.
'96 240SX M/T
Do not completely
release accelerator.
ASCD
A/C switch: OFF
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
8*
EVAP SYSTEM
Pattern #37; ‘96 240SX M/T
NTB98-018
51/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,400 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 1.8 - 2.2 msec
Hold recommended B/F
SCHDL range. Allow road
speed to vary as necessary.
2*
EGR
1*
O2 Sensor
Heater
ENG. RPM:
2,000 - 2,800
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at
55 - 70 MPH
Drive 1.5 minutes
3*
2nd Trip:
Turn ign. key off, add
4 gallons of fuel. Start
engine and allow to
idle 10 min. then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
*
2nd Trip
1st Trip
1st Trip:
Allow engine to idle for
10 minutes then cycle
ignition key off for 10
seconds. Restart engine
and immediately begin
next drive pattern
section.
4
ENGINE
COMPARTMENT
WARM-UP
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed over
3,000 RPM. Allow road speed
to vary if necessary.
Selector lever: "D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
CATALYST
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6*
7*
Idle
1 minute
Downshift then completely
release accelerator more
than 5 seconds without
braking, then idle 1minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
Two Trip Logic
First Trip: Drive all sections 1 through 9.
Second Trip: Turn ign. off. Add 4 gallons fuel. Start engine and drive sections 4, 5, 6, 7, 8, 9.
ECM Part Numbers: 23710-72F10, -72F11, -72F12, -72F13, -72F14, -72F15
System Readiness Test Drive Pattern #38
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow road
speed to change
if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
9*
2nd trip:
End.
1st trip:
key off
then
repeat
4 - 9.
'96 240SX A/T
Do not completely
release accelerator.
ASCD
A/C switch: OFF
Accelerate to 34 MPH
Decelerate to 28 MPH
Accelerate to 34 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx..3,000 RPM
Drive 2 minutes
8*
EVAP SYSTEM
Pattern #38; ‘96 240SX A/T
NTB98-018
52/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
ASCD
A/C switch: ON
ENG. RPM:
2,000 - 2,200
Selector lever: "4th"
B/F SCHDL: 1.5 - 2.0 msec
Hold recommended
B/F SCHDL: range.
Allow road speed to vary
as necessary.
2
Idle
1.5 minutes
EGR
1
O2 Sensor
Heater
ENG. RPM:
1,800 - 2,800
Selector lever:
"5th"
B/F SCHDL:
2.5 - 4.0 msec
Drive at:
55 - 65 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off,
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary
Selector lever: "4th"
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "5th"
B/F SCHDL:
More than 1.5 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"4th"
Downshift
then decel.
O2 SENSOR
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine for either
the first or
second trip.
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-81F00, -81F01, -81F02, -81F03
System Readiness Test Drive Pattern #39
ASCD
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"4th"
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 240SX M/T
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 41 MPH
Decelerate to 34 MPH
Accelerate to 41 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "3rd"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #39; ’97 240SX M/T
NTB98-018
53/59
Start engine,
idle at least
1.5 minutes.
Drive 3 minutes
Idle
1.5 minutes
ASCD
A/C switch: ON
ENG. RPM:
1,400 - 1,600
Selector lever: "D" (OD ON)
B/F SCHDL: 1.8 - 2.2 msec
Hold recommended B/F
SCHDL: range. Allow road
speed to vary as necessary.
2
EGR
1
O2 Sensor
Heater
ENG. RPM:
2,000 - 2,800
Selector lever:
"D" (OD ON)
B/F SCHDL:
2.5 - 4.0 msec
Drive at:
55 - 70 MPH
Drive 1.5 minutes
3
*
1st Trip:
IGN switch "OFF"
10 seconds
(Not more than
5 minutes)
4
KEY
"OFF"
2nd Trip:
Turn ign.. off.
Add 4 gallons of fuel.
Do not decelerate for more
than 3 consecutive seconds.
Keep engine speed above
3,000 RPM. Allow road speed to
vary if necessary.
Selector lever:
"D" (OD OFF)
Cruise at 50 - 60 MPH
Drive 3 minutes
5
CATALYST
A/C switch: ON
ENG. RPM: 2,100 - 2,300
Selector lever: "D" (OD ON)
B/F SCHDL:
More than 1.8 msec
Steady state cruise at
53 - 58 MPH
Use ASCD or hold accelerator
to keep road speed as steady
as possible.
Drive 3 minutes
6
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Idle
1 minute
Downshift, then completely
release accelerator more
than 5 seconds without
braking, then idle 1 minute.
Selector lever:
"D" (OD OFF)
Downshift
then decel.
O2 SENSOR
If fuel level is greater than 1/2 more time may be required to complete EVAP sections of the drive pattern. Also you may be unable to add fuel as required.
NOTE: It is better to perform this driving test when fuel level is less than 1/2.
the first or
second trip.
70˚C (158˚F)
before starting
engine for either
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic. Drive all sections two times.
First Trip: Drive all sections 1 through 8 then turn ign. off and allow engine to cool below 70˚C. (158˚F).
Second Trip: Start engine, drive sections 1,2,3. Turn ign. off and add 4 gallons of fuel in section 4, then start engine and drive sections 5, 6, 7, 8.
ECM Part Numbers: 23710-81F10, -81F11, -81F12, -81F13
System Readiness Test Drive Pattern #40
ASCD
Idle
1 minute
Hold the accelerator
pedal as steady as
possible. Allow speed
to change if necessary.
ASCD
A/C switch: OFF
Selector lever:
"D" (OD OFF)
Steady state cruise at
31 - 44 MPH
Drive 2 minutes
8*
2nd trip:
End.
1st trip:
key off
then
repeat
1 - 8.
'97 240SX A/T
A/C switch: OFF
Do not completely
release accelerator.
Accelerate to 34 MPH
Decelerate to 28 MPH
Accelerate to 34 MPH
B/F SCHDL:
Less than 2.0 msec
Selector lever: "2"
ENG RPM:
Approx.
3,000 RPM
Drive 2 minutes
7*
EVAP SYSTEM
Pattern #40; ’97 240SX A/T
NTB98-018
54/59
*
Start engine and idle at
least 1.5 minutes.
Drive 1.5 minutes
Idle 1.5 minutes
ENG. RPM:
2,000 - 2,800
B/F SCHDL:
1.8 - 3.0 msec
Selector lever: "5th"
Drive at
55 - 65 MPH
2*
EGR
1*
O2 Sensor Heater
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Allow engine to idle for at least 10 minutes.
3
ENGINE COMPARTMENT
WARM-UP
Do not decelerate for more than
3 consecutive seconds.
End
'96 300ZX (Non-turbo) M/T
DownA/C switch: ON
ENG. RPM: 2,300 - 2,400
B/F SCHDL: More than 1.3 msec
Selector lever: "5th"
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Selector lever: "4th"
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
5*
O2 SENSOR
Cruise at 50 - 60 MPH
Drive 3 minutes
4*
CATALYST
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
32˚C (95˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-54P60, -54P61
System Readiness Test Drive Pattern #41
Pattern #41; ‘96 300ZX (Non-turbo) M/T
NTB98-018
55/59
*
Start engine and idle at
least 1.5 minutes.
Drive 1.5 minutes
Idle 1.5 minutes
ENG. RPM:
2,000 - 2,800
B/F SCHDL:
1.8 - 3.0 msec
Selector lever: "5th"
Drive at
55 - 65 MPH
2
EGR
1
O2 Sensor Heater
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Allow engine to idle for at least 10 minutes.
3
ENGINE COMPARTMENT
WARM-UP
Do not decelerate for more than
3 consecutive seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Second Trip:
End
First Trip:
Cycle ign.
switch Off
then repeat
sections 1 - 5
'96 300ZX (Non-turbo) M/T
A/C switch: ON
ENG. RPM: 2,300 - 2,400
B/F SCHDL: More than 1.3 msec
Selector lever: "5th"
Steady state cruise at: 53 - 58 MPH
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Cruise at 50 - 60 MPH
Drive 3 minutes
5
O2 SENSOR
Selector lever: "4th"
Drive 3 minutes
4
CATALYST
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
70˚C (158˚F)
before starting
engine.
Pre-check
All Items: Two Trip Logic.
First Trip: Drive all sections 1 through 5, then turn ign. off and allow engine to cool to 158˚F. to meet Pre-check condition for second trip.
Second Trip: Drive all sections 1 through 5 again.
ECM Part Numbers: 23710-54P62, -54P74
System Readiness Test Drive Pattern #42
Pattern #42; ‘96 300ZX (Non-turbo) M/T
NTB98-018
56/59
*
Start engine and idle at
least 1.5 minutes.
Drive 1.5 minutes
Idle 1.5 minutes
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
1.9 - 3.0 msec
Selector lever:
"D" (OD ON)
Drive at
55 - 75 MPH
2*
EGR
1*
O2 Sensor Heater
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Allow engine to idle for at least 10 minutes.
3
ENGINE COMPARTMENT
WARM-UP
Do not decelerate for more than 3 consecutive
seconds.
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
End
'96 300ZX (Non-turbo) A/T
DownA/C switch: ON
ENG. RPM: 2,100 - 2,300
B/F SCHDL: More than 1.4 msec
Selector lever: "D" (OD ON)
Steady state cruise at: 53 - 58 MPH
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Cruise at 50 - 60 MPH
Drive 3 minutes
5*
O2 SENSOR
Selector lever: "D" (OD OFF)
Drive 3 minutes
4*
CATALYST
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
32˚C (95˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-54P65, -54P66
System Readiness Test Drive Pattern #43
Pattern #43; ’96 300ZX (Non-turbo) A/T
NTB98-018
57/59
*
Start engine and idle at
least 1.5 minutes.
Allow engine to idle for at least 10 minutes.
ENG. RPM:
1,800 - 2,800
B/F SCHDL:
1.9 - 3.0 msec
Do not decelerate for more than
3 consecutive seconds.
Second Trip:
End
First Trip:
Cycle ign.
switch Off
then repeat
sections 1 - 5
'96 300ZX (Non-turbo) A/T
A/C switch: ON
ENG. RPM: 2,100 - 2,300
B/F SCHDL: More than 1.4 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Cruise at 50 - 60 MPH
Selector lever: "D" (OD OFF)
Drive 3 minutes
5
O2 SENSOR
Steady state cruise at: 53 - 58 MPH
Selector lever:
"D" (OD ON)
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Drive 3 minutes
4
CATALYST
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Drive 1.5 minutes
Idle 1.5 minutes
3
ENGINE COMPARTMENT
WARM-UP
Drive at
55 - 75 MPH
2
EGR
1
O2 Sensor Heater
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
70˚C (158˚F)
before starting
engine.
Engine coolant
temperature
must be below
Pre-check
All Items: Two Trip Logic.
First Trip: Drive all sections 1 through 5, then turn ign. off and allow engine to cool to 158˚F. to meet Pre-check condition for second trip.
Second Trip: Drive all sections 1 through 5 again.
ECM Part Numbers: 23710-54P67, -54P75
System Readiness Test Drive Pattern #44
Pattern #44; ’96 300ZX (Non-turbo) A/T
NTB98-018
58/59
*
Start engine and idle at
least 1.5 minutes.
Allow engine to idle for at least 10 minutes.
ENG. RPM:
1,600 - 2,400
B/F SCHDL:
1.4 - 2.1 msec
B/F SCHDL: More than 1.0 msec
DownA/C switch: ON
ENG. RPM: 1,900 - 2,100
End
'96 300ZX (Turbo) M/T
Do not decelerate for more than 3 consecutive
seconds.
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Selector lever: "4th"
Selector lever: "5th"
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
5*
O2 SENSOR
Cruise at 50 - 60 MPH
Selector lever:
"5th"
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Drive 3 minutes
4*
CATALYST
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Drive 1.5 minutes
Idle 1.5 minutes
3
ENGINE COMPARTMENT
WARM-UP
Drive at
55 - 65 MPH
2*
EGR
1*
O2 Sensor Heater
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
Engine coolant
temperature
must be below
32˚C (95˚F)
before starting
engine.
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-54P00, -54P01, -54P02, -54P03, -54P04, -54P70
System Readiness Test Drive Pattern #45
Pattern #45; ‘96 300ZX (Turbo) M/T
NTB98-018
59/59
*
Start engine and idle at
least 1.5 minutes.
Allow engine to idle for at least 10 minutes.
ENG. RPM:
1,600 - 2,600
B/F SCHDL:
1.4 - 2.5 msec
DownA/C switch: ON
ENG. RPM: 1,800 - 2,000
B/F SCHDL: More than 1.0 msec
Selector lever: "D" (OD ON)
Use ASCD or hold accelerator to keep
road speed as steady as possible.
Steady state cruise at: 53 - 58 MPH
Drive 3 minutes
5*
O2 SENSOR
End
'96 300ZX (Turbo) A/T
Do not decelerate for more than 3 consecutive
seconds.
Selector lever: "D" (OD OFF)
Cruise at 50 - 60 MPH
Selector lever:
"D" (OD ON)
Then cycle ignition switch OFF for 10 seconds.
Restart engine and immediately begin next
drive pattern section.
Drive 3 minutes
4*
CATALYST
Keep engine speed above 3,000 RPM.
Allow road speed to vary if necessary.
Drive 1.5 minutes
Idle 1.5 minutes
3
ENGINE COMPARTMENT
WARM-UP
Drive at
55 - 75 MPH
2*
EGR
1*
O2 Sensor Heater
Dark shading behind section number indicates this drive pattern section must be repeated, without turning the ignition off, if it is interrupted by releasing
the accelerator when not directed to do so.
before starting
engine.
must be below
32˚C (95˚F)
Engine coolant
temperature
Pre-check
One Trip Logic for all sections.
Drive all sections one time.
ECM Part Numbers: 23710-54P05, -54P06, -54P07, -54P08, -54P09, -54P71
System Readiness Test Drive Pattern #46
Pattern #46; ‘96 300ZX (Turbo) A/T
NTB98-018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising