Operating instructions HP touchsmart iq700

Operating instructions HP touchsmart iq700
You can read the recommendations in the user guide, the technical guide or the installation guide for HP touchsmart iq700. You'll
find the answers to all your questions on the HP touchsmart iq700 in the user manual (information, specifications, safety advice,
size, accessories, etc.). Detailed instructions for use are in the User's Guide.
User manual HP touchsmart iq700
User guide HP touchsmart iq700
Operating instructions HP touchsmart iq700
Instructions for use HP touchsmart iq700
Instruction manual HP touchsmart iq700
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
Manual abstract:
No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP. Hewlett-Packard
Company P.O. Box 4010 Cupertino, CA 95015-4010 USA Copyright © 2007 Hewlett-Packard Development Company, L.P. May be licensed in the United
States by one or both of U.S. Patents Nos. 4,930,158 and 4,930,160 until August 28, 2008. Microsoft and Windows Vista are U.
S. registered trademarks of Microsoft Corporation. The Windows logo and Windows Vista are trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries/regions. @@@@@@@@Click the Windows Start Button® on the taskbar, click All Programs, User Guides, and
then click Getting Started. Limited Warranty and Support guide provides information about your computer warranty and how to obtain support.
Troubleshooting and Maintenance Guide provides information about tasks you can perform to ensure the trouble-free operation of your computer and to ease
the recovery of important information on your computer should problems arise in the future. It also contains a series of tables that describe solutions you can
try to resolve problems that may occur when you install and use your computer. For more detailed information about where you will find specific information
in each of these guides, refer to Locating Information about Your Computer in this guide. HP Touchsmart PC User Guide i Accessing Software and
Performing Other PC Tasks You can access your software and perform various tasks on your HP TouchSmart PC using the touch screen, keyboard, mouse,
stylus, or remote control. Some tasks are better suited to the touch screen, such as using the HP SmartCenter programs, browsing the Internet, or accessing
your favorite programs.
Some activities, such as typing search text, are better suited for the keyboard. You always have the flexibility to use various ways to navigate your PC, create
messages, and access your music, TV programs, and photos. NOTE: All software that you purchase and install separately is accessible with the touch screen,
but some programs are easier to use with a stylus, keyboard, or mouse. Accessing Software and Performing Other PC Tasks Software and other PC activities
HP SmartCenter HP SmartCalendar HP Photosmart Touch Windows Media Center Software included with the PC Software you install Internet access
Windows Vista operating system Desktop navigation Turn the PC on or put it in Standby mode Touch screen Finger/Stylus Best Best Best Better Good Good
Good Good Better On only Keyboard/mouse Good Good Good Good Best Best Best Best Best Best Remote control Yes No No Best No No No No No Best ii
HP Touchsmart PC User Guide Table of Contents Setting Up the HP TouchSmart PC .......
..........
.....
.....
..........
..........
.....
.....
..........
..........
....1 HP TouchSmart PC Cables.
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.........7 Setting Up the HP TouchSmart PC.
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.........7 Using surge protection .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.........7 Connecting the power cord .
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
..7 Setting up the wireless keyboard and mouse...
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..8 Turning on the HP TouchSmart PC ........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......8 Using the Wireless Keyboard or Mouse ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.......9 Using the wireless keyboard ...
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....9 Using the wireless mouse.
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
....11 Replacing batteries in the keyboard or mouse ......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
11 Manually sync the wireless keyboard or mouse ..........
..........
.....
.....
..........
..........
.....
.....
..........
....12 Connecting the TV Signal Source to the PC......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.........13 Connecting the IR emitter.
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
....14 Connecting an HP Photo Printer .
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
....15 Connecting a printer......
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
15 Setting Up the Remote Control .....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.......16 Using a Wireless Network and Bluetooth Devices ...
..........
.....
.....
..........
..........
.....
.....
..........
..........
..17 Setting up a wireless local area network ...
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.....17 Using Bluetooth devices .....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.17 Connecting to the Internet.........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
18 Setting up a network and the HP TouchSmart PC .....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..19 Using the HP TouchSmart PC........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....21 Using the HP TouchSmart PC Screen.
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
...21 Selecting items with your touch screen .......
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....21 Optimizing the screen for touch or the mouse .
..........
..........
.....
.....
..........
..........
.....
.....
..........
.....21 About touch screen technology .....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.22 Cleaning the HP TouchSmart PC Screen ....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.....23 Using the stylus .....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...23 Using the Built-in Web Camera and Microphone .......
.....
.....
..........
..........
.....
.....
..........
..........
.....
....24 Having a video chat or making conference calls .
..........
..........
.....
.....
..........
..........
.....
.....
..........
.24 Table of Contents iii Using the HP TouchSmart PC Software.........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..24 What is HP SmartCenter?........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.24 Navigating in HP SmartCenter ....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
...26 Opening HP SmartCenter .......
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.......26 Using the remote control with HP SmartCenter ...
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..26 Changing the weather location ........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
........27 Changing the HP SmartCenter clock settings ..
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.28 Using HP SmartCalendar....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.29 Moving notes to your calendar.........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
........33 Using HP Photosmart Touch ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
....34 Opening HP Photosmart Touch......
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.34 Transferring your photos to the PC.........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...34 Working with digital images.......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
...34 HP Photosmart Touch shortcuts ..
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....35 Adding pictures to your HP Photosmart Touch library .
..........
..........
.....
.....
..........
..........
.....
.....
.....35 Searching for pictures with HP Photosmart Touch.....
..........
.....
.....
..........
..........
.....
.....
..........
.......36 Selecting pictures in HP Photosmart Touch ...
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
........36 Editing pictures in HP Photosmart Touch ..
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..36 Printing pictures in HP Photosmart Touch ........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
37 Other HP SmartCenter Features.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
......38 Personalizing your HP SmartCenter page ....
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
...38 Changing what you can launch from HP SmartCenter ..
..........
..........
.....
.....
..........
..........
.....
.....
...39 Using the touch screen to access Windows Media Center .......
..........
.....
.....
..........
..........
.....
.....
.......41 Using Tablet PC software to enter text with the touch screen ...
..........
.....
.....
..........
..........
.....
.....
...43 Using Windows Journal software to create hand-written notes and drawings .......
..........
.....
.....
......43 Upgrading the HP TouchSmart PC ....
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
45 Safety Information .....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
....45 Opening and Closing the HP TouchSmart PC.
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......45 Preparing the HP TouchSmart PC....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
45 Before opening the HP TouchSmart PC.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......46 After closing the HP TouchSmart PC....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......46 Removing the rear cover ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.47 Replacing the rear cover .........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......48 Removing the vertical cover ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
..48 Replacing the vertical cover ...
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
........49 Adding Memory..
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
....ly insert various photo memory cards to quickly transfer your digital photos to the PC. Left slot accepts CompactFlash I and II, and MicroDrive. Right slot
accepts SD, MMC, MS, MS-PRO, and xD. Memory card reader indicator -- light to show current activity for the memory card reader. Activity LED indicator
lights -- light to show current activity for the hard disk drive, TV recording, the HP SmartCalendar event reminder, and wireless/Bluetooth devices. Media
contton to pop out and then remove the drive.
Press to eject PMD PMD bay HP Poc - For specific steps to disconnect and remove the drive, see "Disconnecting the Drive" in the "Using the HP Personal
Media Drive and the HP Pocket Media Drive" chapter of the Getting Started guide. 6 HP TouchSmart PC User Guide ket Media D rive + HP TouchSmart PC
Cables For more information about cables, refer to the printed cable flyer that came with your HP TouchSmart PC. Power cable to connect the PC to the
power source. Ethernet (RJ-45) cable (sold separately) to optionally connect the PC to a wired LAN (Ethernet) port. VGA adapter cable connects from the
VGA Out connector to a standard 15-pin VGA connector on a TV or a monitor.
HP printer Y-cable (Type B USB) with power to connect HP Photosmart A510 and A610 Series printer models without using a separate power cable. IR
(infrared) emitter cable to connect the HP TouchSmart PC (at the IR Out connector) to operate the remote sensor on a set-top box. Setting Up the HP
TouchSmart PC Setting up the HP TouchSmart PC is simple; just place it and connect the power cord. Then, pull the battery tabs on the wireless keyboard
and mouse, turn on the mouse, and then turn on the PC, and you are ready to begin using you HP TouchSmart PC.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
You can also: Connect to the Internet using wireless or wired (optional) connection.
See "Connecting to the Internet." Insert the batteries in the remote control. See "Setting up the remote control to use with Windows Media Center." Make
other connections, such as TV input signal. See "Connecting the TV Signal Source to the PC." Connect a printer. See "Connecting a printer." WARNING:
Please read "Additional Safety Information" in the Limited Warranty and Support Guide before installing and connecting your HP TouchSmart PC to the
electrical power system. Read the topics in this section to learn more about setting up your HP TouchSmart PC. Look in the HP TouchSmart PC box for
printed details or updates regarding your HP TouchSmart PC.
Using surge protection Help protect your HP TouchSmart PC and accessories by connecting all power cords for your HP TouchSmart PC and peripheral
devices (such as a monitor, printer, or scanner) to a surge protection device such as a power strip with surge protection or an uninterruptible power supply
(UPS). Many surge protection devices have surge protection inputs and outputs for modem or telephone lines. Telephone lines are a common path for
lightning spikes to get into your system. Some surge protection devices have surge protection for television cable connections as well. Use those if your HP
TouchSmart PC has a television tuner installed. Not all power strips provide surge protection; the power strip must be specifically labeled as having this
capability. Use a power strip whose manufacturer offers a damage replacement policy that replaces your equipment if surge protection fails. Connecting the
power cord Connect the power cord to the AC power cord connector on the back of the HP TouchSmart PC, and then plug the other end into a surge
protection device or the wall outlet. The AC power indicator turns green when the cord is connected to a power source. Setting Up the HP TouchSmart PC 7
Setting up the wireless keyboard and mouse CAUTION: You must follow the steps in the order listed to enable your keyboard and mouse to work with your
HP TouchSmart PC.
To set up the wireless keyboard and mouse: 1 Engage the batteries by pulling out the battery tabs from the bottom of the mouse and the keyboard. Battery pull
tab Connect button 2 For the mouse only, move the switch on the bottom of the mouse to the On position. 3 Place the mouse and the keyboard on the same
surface as the HP TouchSmart PC and within 12 inches (30 centimeters) of it. 4 When the HP TouchSmart PC is turned on, the keyboard and mouse
automatically syncs. 5 If the mouse or the keyboard does not work properly, you may have to manually sync them or replace the batteries.
See "Manually sync the wireless keyboard or mouse" or "Replacing batteries in the keyboard or mouse." Turning on the HP TouchSmart PC Press the
On/Standby button on the front of the HP TouchSmart PC to easily turn on your HP TouchSmart PC. It takes about 20 minutes to complete the initial setup by
following the onscreen instructions. You are ready to begin using you HP TouchSmart PC. For more information, see "Turning On Your HP TouchSmart PC
for the First Time" in the Getting Started guide.
You can also turn the HP TouchSmart PC on or in Standby mode by pressing the On/Standby button on keyboard or the remote control. 8 HP TouchSmart PC
User Guide Using the Wireless Keyboard or Mouse You can use the keyboard within approximately 9.8 feet (3 meters) and the mouse within approximately
9.8 feet (3 meters) of the HP TouchSmart PC. Using the wireless keyboard This section describes some information about the wireless keyboard. For more
information about keyboards, refer to "Using the Keyboard" in the Getting Started guide. Your keyboard is either a US version or a UK version. Keyboards
US Keyboard is shown. UK key differences are shown above the keyboard. £ 2 3 $ 4 @ þ ÷ # On Display Off Special keyboard buttons The wireless keyboard
has some special buttons and keys.
The Caps Lock key is used to lock the keyboard to capital letters. When the Caps Lock is on, the Caps Lock light flashes briefly each time a key is pressed. You
can customize some of the special buttons on the keyboard to open different programs or files, or to go to favorite Web sites. For more information, see
"Customizing the keyboard buttons" in the Getting Started guide. Setting Up the HP TouchSmart PC 9 Special Keyboard Buttons Button or key Description
On/Standby turns the HP TouchSmart PC on or puts the HP TouchSmart PC into standby or sleep mode. Volume Up and Volume Down adjust the speaker
sound level. Mute turns the sound off or on. The Function (Fn) key acts as a shift-down key for the Function keys; press Fn with a Function key (F1 through
F12) to select the lower feature of the key. The Back key (press Fn+F1) moves back one window or Web page. The Forward key (press Fn+F2) moves
forward one window or Web page.
The Internet key (press Fn+F3) opens your Internet browser. Can be configured to open any Web site or software program. The E-mail key (press Fn+F4)
opens the e-mail program. Can be configured to open any Web site or software program. The Display On/Off (press Fn+F5) turns off the display.
Press the Display On/Off (press Fn+F5) again to turn the display back on. The Brightness Down (press Fn+F7) and Brightness Up (press Fn+F8) adjust the
screen brightness. On The Cut key (press Fn+F9) removes the selected item and creates a copy that can be pasted. The Copy key (press Fn+F10) copies the
selected item. The Paste key (press Fn+F11) pastes the selected item.
The HP Help key (press Fn+F12) opens Help and Support. 10 HP TouchSmart PC User Guide Using the wireless mouse The cursor on the screen moves
when you move the mouse. The wireless mouse operates with a Class 1 laser beam, which you cannot see. The mouse indicator light on the bottom of the
mouse blinks when you turn it upside down to show that the batteries and the laser are working, and that the laser is off to protect you. Do not store the mouse
upside down. To use the mouse, move the switch on the bottom of the mouse to the On position. Use the mouse on most surfaces. To conserve battery power,
when not in use, move the switch on the bottom of the mouse to the Off position before storing the mouse. For more information about the mouse, refer to
"Using the Mouse" in the Getting Started guide. Replacing batteries in the keyboard or mouse Review these tips: When the unit does not operate properly,
replace the batteries in the keyboard or mouse.
Do not mix different types of batteries together. For example, do not mix rechargeable and non-rechargable, alkaline and carbon-zinc (Ni-Cd), or old
batteries with fresh ones. Be sure to place the batteries in the correct position (+ on the battery matching the + in the battery compartment).
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
Reversed batteries may cause damage to the device. When not using the mouse or keyboard for a couple weeks or more, remove the batteries to prevent
damage or injury from possible battery leakage. Do not try to recharge batteries that are not intended to be recharged; they can overheat and rupture. Follow
the battery manufacturer's directions for the batteries you are using. Always remove batteries as soon as they become weak. Weak batteries can leak and
severely damage the unit. The battery life depends on how much the unit is used.
Do not take apart the batteries, heat them, or throw them into a fire. To replace the batteries: 1 For the mouse only, move the switch on the bottom of the
mouse to the Off position. 2 Remove the battery cover from the bottom of the keyboard or mouse. 3 Remove the batteries. 4 Insert new batteries, matching the
orientation shown on the housing.
Use four AAA batteries for the keyboard, and two AA batteries for the mouse. 5 Replace the battery cover. 6 For the mouse only, move the switch on the
bottom of the mouse to the On position. 7 Place each unit on the same surface as the HP TouchSmart PC and within 39 inches (1 meter) of it. 8 With the HP
TouchSmart PC turned on, the keyboard/mouse connect indicator on the front of the HP TouchSmart PC lights when the keyboard and mouse are synced
(recognized).
The unit should be automatically recognized in about 5 seconds. Press a key on the keyboard or move the mouse to check operation. NOTE: The keyboard and
mouse do not lose sync during a battery charge. If either unit does not work properly, you may have to manually sync them. See "Manually sync the wireless
keyboard or mouse." Setting Up the HP TouchSmart PC 11 Manually sync the wireless keyboard or mouse Use these steps to manually sync the keyboard or
mouse with the HP TouchSmart PC when either unit does not work properly after replacing the batteries. 1 For the mouse only, move the switch on the
bottom of the mouse to the On position. 2 Place the keyboard or mouse on the same surface and within close proximity (12 inches or 30.5 centimeters) as the
HP TouchSmart PC. 3 Using a ball point pen, press and hold the keyboard/mouse Connect button on the front of the HP TouchSmart PC until the indicator
light blinks.
You have 60 seconds to complete step 4 or 6. 4 For the keyboard, press the Connect button on the bottom until the Caps lock indicator light (located on top
next to the Caps lock key) starts blinking. The sync should occur within 5 seconds. 5 Repeat step 3 to begin the syncing of the mouse. 6 On the bottom of the
mouse, press the Connect button until the indicator light starts blinking. The syncing should occur within 5 seconds. 7 If the keyboard or mouse does not
operate properly, repeat steps 1 through 6. NOTE: After pressing the Connect button on the system, press only the Connect button on the keyboard or the
mouse. Pressing another key may cause the sync to take longer or to time out. If the receiver times out, you must press the system Connect button until the
LED blinks, and then press the keyboard or the mouse Connect button until the LEDs blink.
12 HP TouchSmart PC User Guide Connecting the TV Signal Source to the PC NOTE: The number and type of cables required to connect your HP
TouchSmart PC may vary by model. You may need to purchase extra cables separately. Your HP TouchSmart PC may not include all the cables you need for
your computer setup, and the cables included may vary by model. Use these steps to connect the TV signal source, the FM signal antenna, or video and audio
from a set-top box or DVD player. Some HP TouchSmart PC models have only the TV connector.
Shown below are three different TV tuner connectors your HP TouchSmart PC may include: TV/In Cable antenna connector only If your TV tuner looks like
this, follow this procedure: 1 Connect the coaxial cable from your TV antenna or TV cable provider to the TV In connector on the left side of the HP
TouchSmart PC. Or Plug an S-V/Cable antenna video cable into the S-Video connector in the front Connectivity Center of the HP TouchSmart PC. Plug the
other end of the cable into your set-top box or other device that is providing the signal source for the TV. 2 If you are using the S-Video connector, plug audio
cables from your settop box into the audio left and right connectors in the front Connectivity Center of the HP TouchSmart PC. 3 If you are using the set-top
box, connect the IR emitter cable.
See "Connecting the IR emitter." TV In Cable/ antenna FM antenna, TV In, S-Video, Video Composite, left and right audio connectors If your TV tuner looks
like this, use the following procedure: 1 Connect the coaxial cable from your TV antenna or TV cable provider to the TV In/Cable/Ant connector on the left
side of the HP TouchSmart PC. Or Plug a cable into the S-Video or Video (composite) connector on the left side of the HP TouchSmart PC; use an S-Video
cable or composite video cable. Plug the other end of the cable into your set-top box or other device that is providing the signal source for the TV. 2 If you are
using the S-Video or video connector, plug audio cables from your set-top box into the audio left and right connectors on the left side of the HP TouchSmart
PC. 3 Push the coaxial cable from your FM antenna or signal provider onto the FM connector on the left side of the HP TouchSmart PC. 4 If you are using
the set-top box, connect the IR emitter cable. See "Connecting the IR emitter." Right Left Audio In S-Video Audio In TV In Cable/ Composite antenna Setting
Up the HP TouchSmart PC 13 FM antenna, TV In, HDTV/ATSC, S-Video, left and right audio connectors If your TV tuner looks like this, use the following
procedure: 1 Connect the coaxial cable from your TV antenna or TV cable provider to the Cable/Ant connector on the left side of the HP TouchSmart PC. Or
Plug a cable into the S-Video or video (composite) connector on the left side of the HP TouchSmart PC; use an S-Video cable or composite video cable.
Plug the other end of the cable into your set-top box or other device that is providing the signal source for the TV. 2 If you are using the S-Video or video
connector, plug audio cables from your set-top box into the audio left and right connectors on the left side of the HP TouchSmart PC. 3 Push the coaxial cable
from your FM antenna or signal provider onto the FM connector on the left side of the HP TouchSmart PC. 4 If you are using the set-top box, connect the IR
emitter cable. See "Connecting the IR emitter." HDTV/ ATSC TV In Cable/ antenna Right Left Audio In Audio In S-Video Connecting the IR emitter The
remote infrared emitter cable is a small device that connects to the HP TouchSmart PC at the IR Out connector and covers the remote sensor on a set-top box.
It enables the remote control that came with your HP TouchSmart PC and the Windows Media Center program to operate the set-top box. 1 If you have a
cable TV set-top box, a satellite set-top box, or another set-top box that controls your TV signal, connect the IR emitter cable (A) to IR Out connector (D) on
the back of the HP TouchSmart PC.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
2 Remove the paper from the backing tape on the end of the cable (B), and then press the end of the cable over the remote infrared (IR) sensor (receiver)
window on the set-top box (C). To locate the remote infrared sensor window, shine a flashlight through the plastic on the front of the set-top box.
3 In the Windows Media Center, select the channel using the screen, the display channel buttons, or the remote control channel buttons. When using the
remote control, point the remote control at the HP TouchSmart PC front (E), not at the set-top box. C D A B + - On/ Off Visua lizati on o Radi Mus ic TV
Recorded re Pictu Print Slide Show 14 HP TouchSmart PC User Guide Assp ect E men u Guid o Vide DVD e Live TV OK k bac Volu me + _ e Mut Reco rd
ChEjec t e Mor Info Cha nne l Ch+ 1 4 ghi 2 abc 7 pqrs 5 3 jkl def # 8 tuv 6 mno 0 9 Clea r wxyz * r Ente Connecting an HP Photo Printer Some HP photo
printer models (A510 Series and A610 Series sold separately) can be placed on the printer dock on the back of the HP TouchSmart PC to provide a photo
kiosk experience at home and save counter space at the same time. You can power the HP printer without using a separate power cable by connecting the
printer to your HP TouchSmart PC using the included HP printer Y-cable. NOTE: If using the HP printer (USB and power) Y-cable to connect the HP printer
to the HP TouchSmart PC, when the HP TouchSmart PC goes into sleep mode, the printer batteries do not charge and printing may be terminated.
The HP TouchSmart PC must remain operational while printing completes. Connecting a printer 1 Connect cabling to the printer: NOTE: Printer installation
procedure varies based on manufacturer. Follow manufacturer instructions. Open the paper output tray of an HP Photosmart A510 or A610 Series printer
(sold separately) and place it on the back of the HP TouchSmart PC. Connect the HP printer (USB and power) Y-cable to the printer AC power cord
connector and USB connector.
Or Connect the power cord and USB cable to the printer. Plug the power cord into a power source. 2 Connect cabling to the HP TouchSmart PC: Connect
the other end of the HP printer Y-cable to the paired USB connector and HP printer power connector on the back of the HP TouchSmart PC. Or Connect the
USB cable to the back of the HP TouchSmart PC. 3 Turn on the printer. 4 To print a photo, open the back of the photo printer and insert photo paper. 5 Print
the photo. The photo ejects out of the printer and through the front of the HP TouchSmart PC. For information about using the printer, refer to "Using a
Printer" in the "Managing Files" chapter of the Getting Started guide. NOTE: If your photo doesn't print, make sure the paper output tray and the back of the
printer are open for the paper to eject properly.
+ Ph + X C or ot o Fix La yo ut Me nu P ri nt HP printer Y-cable Se + Zo om H P Ph ot os m ar t ct re O K A 61 7 le ct HP printer dock Setting Up the HP
TouchSmart PC 15 Setting Up the Remote Control Setting up the remote control to use with Windows Media Center Remove the back cover of the remote
control and insert two AA batteries in the remote control. Make sure the batteries are inserted in the correct direction with the + and symbols on the batteries
matching the ones on the remote control. Using the remote control Point the remote control at the remote control sensor at the front of the HP TouchSmart
PC, and press a button. On/Off Visualization Print Radio Music Picture Video rd ed TV Guide Liv e TV DVD menu Reco OK back Volume More Info Slid
Channel Ch+ + _ Record Mute Ch- Eject 1 4 2 5 8 0 Clear abc 3 6 def ghi jkl mno 7 pqrs # tuv 9 wxyz * Enter Pressing the On/Standby button turns the HP
TouchSmart PC on or puts it in Standby (sleep) mode. For more information about the remote control, refer to "Using the Windows Media Center Remote
Control" in the Getting Started guide. 16 HP TouchSmart PC User Guide Sh e ow Asspect Using a Wireless Network and Bluetooth Devices Your HP
TouchSmart PC is designed to support a wireless local area network (LAN) and wireless connections with other Bluetooth devices. Setting up a wireless local
area network Your home LAN may consist of a wired or a wireless network that you can use to connect your HP TouchSmart PC to other devices on the
network, including other computers. The network components may include a hub or a switch, which can connect multiple devices to the network, or a router,
which can connect computers or a broadband Internet connection to the network. This network connection also enables you to share data, and printers or
other devices among your computers. The network connection to the Internet is usually through a broadband (DSL or cable) modem, which may require a
separate subscription.
For more information, see "Connecting to the Internet." Using Bluetooth devices Bluetooth devices create a personal area network (PAN) to connect other
Bluetooth devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each device communicates directly with the other devices,
and the devices must be relatively close together. Setting Up the HP TouchSmart PC 17 Connecting to the Internet For Internet connectivity (optional), use
wireless LAN, or connect an Ethernet cable for a wired LAN connection: For a wireless LAN, the HP TouchSmart PC includes a built-in wireless LAN, which
you can use to access your wireless home network. The HP TouchSmart PC is also Bluetooth enabled, so you can connect all kinds of wireless devices.
See "Using Bluetooth devices." For a wired LAN, connect an Ethernet cable (sold separately) to the Ethernet connector on the back of the HP TouchSmart
PC, and then connect the other end to the network router or cable modem. NOTE: Broadband modem and router installation procedures vary based on
manufacturer. Follow manufacturer instructions. To set up your Internet connection, the following items are needed: Broadband modem (DSL or cable) with
high-speed Internet service purchased from your Internet service provider (ISP) Wireless or wired router (sold separately) Computer connection: wired or
wireless Wired uses Ethernet cable (sold separately) from computer to network router or cable modem.
c Wireless uses the computer built-in antenna. + c - 18 HP TouchSmart PC User Guide Setting up a network and the HP TouchSmart PC First time wireless
network installation requires that you: 1 Purchase high-speed Internet service. 2 Purchase and install a wireless router. 3 Configure the HP TouchSmart PC
to connect to the wireless network. 4 Add your wired computer or devices to the network (optional). Purchase high-speed Internet service If you already have
high-speed Internet service (DSL or cable), skip to "Purchase and install a wireless router.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
" If you do not have high-speed service, proceed with the steps below. 1 Contact a local ISP to purchase high-speed Internet service and a DSL or cable
modem. The ISP will help set up the modem, install an data cable to connect the modem to the service, and test the service. If the ISP provides a single device
that acts as both a modem and a wireless router, you can proceed to "Purchase and install a wireless router.
" 2 Your ISP will give you a user ID and password to access the Internet through its service. Record this information. NOTE: HP recommends that you
protect your HP TouchSmart PC from Internet viruses by installing a firewall and using anti-virus software that is updated regularly. For more information
about using security software, go to Help and Support. Click Start on the taskbar, click Help and Support. Type Firewall or Anti-virus software into the
search box and press the Enter key. Purchase and install a wireless router Read through these steps before you install the wireless router using the router
manufacturer's instructions and your computer. If you need technical assistance during the router installation, contact the router manufacturer. 1 Many
wireless routers are shipped with a default network name (SSID) and security disabled. The router manufacturer's software allows you to change the SSID
and enable security to protect the privacy of your wireless network.
If you change the default SSID or enable security during the router setup, record the information. You need this information when you configure your
computer and any other existing computers to access the router. 2 The most common security levels are WPA-Personal and WEP. Some router manufacturers
amy provide additional security levels. If you enable router security, record the password and security key.
The password may be called an encryption key, passphrase, or pre-shared key. 3 Locate and use the wireless router manufacturer's instructions to install the
wireless router. After you complete the router installation, return to these steps. 4 Test your wireless router setup by opening the Web browser and accessing
any Web site. Do not continue until you have successfully accessed a Web site.
Setting Up the HP TouchSmart PC 19 Configuring the HP TouchSmart PC to connect to the wireless network 1 Turn on your HP TouchSmart PC. 2 To
connect your HP TouchSmart PC to the wireless network: Right-click the network icon in the system tray, and then select Connect to a network. When the
window opens, select the network and click Connect. Or Right-click the network icon in the system tray, and then select Network and Sharing Center. When
the window opens, select Setup a wireless router or access point, and then follow the onscreen instructions. 3 Test the wireless network by opening your Web
browser and accessing any Web site. Adding your wired HP TouchSmart PC to the network (optional) This optional procedure applies to only those HP
TouchSmart PCs that are already configured to access the Internet. 1 Disconnect power from the broadband modem and the wireless router, and then shut
down your HP TouchSmart PC and the computers you want to add to your network. 2 For each wired computer, connect one end of an Ethernet cable to the
LAN connector on the computer, and then connect the other end of the cable to any available Ethernet connector on the wireless router. 3 Reconnect power to
the modem and wait until the modem has completed its startup cycle.
Reconnect power to the wireless router. Then, turn on the wired computers and your HP TouchSmart PC. 4 Test the network connection for each wired
computer by opening the Web browser and accessing any Web site. 20 HP TouchSmart PC User Guide Using the HP TouchSmart PC Using the HP
TouchSmart PC Screen The angle and height of HP TouchSmart screen is easily adjustable by each person using it. You can move it up and down and tilt it
back and forth to the angle that is comfortable for each person. Selecting items with your touch screen To select items on your touch screen you can: Press
once just like a single mouse click. Tap twice quickly like a double mouse click. Open a secondary menu as you would do when you perform a right mouse
click, by pressing and holding until the menu appears and then moving your finger to select the menu item. @@@@@@4 Press HP TouchSmart Programs.
@@This type of touch screen has a limited in-use life.
Such an overlay also impairs the image quality. @@@@@@@@@@@@@@The touch screen has a protective glass surface that can be cleaned by using
a soft cloth or paper towel dampened with a typical household glass cleaner. To clean the touch screen: 1 Disable the touch screen by turning off the PC and
disconnecting the power cord from the wall. 2 Spray a small amount of a mild glass cleaner onto a lint-free soft cloth. 3 Wipe the surface and each side of the
display to remove any dirt, fingerprints, or other debris that could hinder the touch recognition of the screen.
CAUTION: Do not spray or place the cleaner directly on the screen; spray the cleaner into the cloth and then wipe the sides and surface of the touch screen.
Also, avoid wiping in the top corners where the optics are located. @@@@@@@@@@@@@@2 Enable your Web camera as the default video input.
@@NOTE: This software may require a separate subscription. @@@@@@@@@@C Get the latest weather forecast for your area.
@@D Close, minimize, and maximize your HP SmartCenter window. E F Add a link to a software program or a Web site. @@@@See "Other HP
SmartCenter Features" on page 38. @@@@HP Advisor is available in North America only. @@@@@@@@O Launch Windows Media Center so you can
browse your music collection and play your favorite tracks. P Switch to live TV in Windows Media Center when your PC is connected to a TV signal and you
have set up Windows Media Center to access your TV signal. Q Use the Back button to move back to a previous window. Using the HP TouchSmart PC 25
Navigating in HP SmartCenter You can use touch, the wireless keyboard and mouse, or your remote control to select and deselect items in HP SmartCenter.
You can press Back to HP SmartCenter window. when you want to go back to the main HP SmartCenter Opening HP SmartCenter To open your HP
SmartCenter: HP SmartCenter button 1 Press the HP SmartCenter Or button on the lower-right side of the HP TouchSmart PC display.
1 Press or click the Windows Start Button 2 Press or click All Programs. on the taskbar. 3 Scroll down the Start menu, and then press or click HP. 4 Press or
click HP TouchSmart Programs. 5 Press or click HP SmartCenter. Using the remote control with HP SmartCenter 26 HP TouchSmart PC User Guide You
can use the remote control on the main page of HP SmartCenter. Use the arrow keys to highlight a shortcut, and then use the OK key to activate the
highlighted shortcut. The selected item appears with a box around it. Changing the weather location Your HP TouchSmart PC has a link to a two-day weather
forecast for any area in the United States.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
Your model has Cupertino, California's weather displayed as a default.
To change it to your location: 1 Open the HP SmartCenter page. 2 Press the weather icon. 3 Press Change Zip Code. 4 Use your keyboard or press the touch
keyboard to enter your zip code. 5 Select Fahrenheit or Celsius.
6 Press OK. 7 Press Back to HP SmartCenter when you are finished. Using the HP TouchSmart PC 27 Changing the HP SmartCenter clock settings To
change it to your time zone: 1 Open the HP SmartCenter page. 2 Press the analog or digital Clock icon. 3 Press Change Name and Time Zone under the first
clock or press the clock.
4 Under Clock Name, touch the word Time, and then move your finger over it to highlight the word. When selected, type in a new name such as San Francisco
Time or Uncle Billy. 5 Select your time zone by touching an item in the list. You can view more time zones by using the scroll bar. When finished, touch OK. 6
To enable the other two time zones, place a check in the Enable check box. 28 HP TouchSmart PC User Guide 7 Press Change Name and Time Zone under
the clock you want to add or touch the clock. 8 Under Clock Name, touch the word Time, and then move your finger over it to highlight the word. When
selected, type in a new name such as Hong Kong Time or Mike in Idaho. 9 Select your time zone by touching an item in the list.
You can view more time zones by using the scroll bar. When finished, touch OK 10 Press the Back to HP SmartCenter icon when you are finished. 11 To view
the two other time zones, press the Time icon from the main HP Smart Center page. NOTE: Only one time can appear on the main HP SmartCenter page
unless you move the Clock icon into the top row when you personalize your HP SmartCenter page. Refer to "Changing what you can launch from HP
SmartCenter" on page 39. Using HP SmartCalendar HP SmartCalendar is a shared calendar and message center where you can manage your family's
schedule. @@@@3 Scroll down in the Start menu, and then press or click HP. 4 Press or click HP TouchSmart Programs. 5 Press or click HP SmartCenter.
6 Press the HP SmartCalendar icon.
on the taskbar. @@@@@@You can view it as one month, one year, one week, or one day. @@@@@@The main HP SmartCenter page displays up to three
appointments. @@@@@@Use the touch keyboard or your physical keyboard to type in an event. 4 Touch the text box next to Where, and type in where your
event takes place.
5 Press the drop-down arrows next to your start and end dates and the start and end times to enter this information for your date and time of your event. 6
Touch the text box next to Description to add more information about your event. 7 If this is a reoccurring event, use the drop-down arrow under Repeat, and
select Daily, Weekly, Monthly, or Yearly. 8 If you want to set a reminder to alert you before the event, use the drop-down arrow under Reminder and select 15
minutes before, 1 hour before, 1 day before, or 1 week before. 9 Under Assign To, use the drop-down arrow to assign the event to one or more members of the
family.
NOTE: Each member or group must have a user account set up in HP SmartCalendar in order to show up in this list. 10 Press Done after you have entered
all of your event information. Your event appears as a white dot on your calendar. To view it, just touch the date, and then touch the event. 11 To print a date,
just touch the date and then press the Print button on the screen and follow onscreen instructions. Using the HP TouchSmart PC 31 Adding user accounts in
HP SmartCalendar You can set up user accounts in HP SmartCalendar so that each person can have access to personal notes that others assign to you. To
add user accounts in HP SmartCalendar: 1 Open HP SmartCalendar window. 2 Press the add user icon on the toolbar. 3 Press Manage Users. 4 Press Add
User, Edit User, or Delete User.
5 If you selected Add User, type the name, select an icon, or press Browse to find your icon. 6 Press Save. 7 Press Close. Deleting an event To delete an event
from your HP SmartCalendar, touch the date, touch the event, and then press the Delete button on the screen. Creating text notes with the touch screen,
stylus, or keyboard 1 Open HP SmartCalendar. 2 Press Write Note. 3 Select a paper color. 4 Press the drop-down arrow next to Assign note and select a user,
and then press Done. 5 Select a tool to enter your text and graphics: Select the Pen icon to use your finger or the stylus. Select the ABC icon to use your
keyboard.
Use the Eraser tool to erase a hand-written message and start over. 6 Enter your text using the tool you selected. You can create a note using different tools. 7
Press Done when you are finished. Your note appears on your bulletin board next to your calendar.
32 HP TouchSmart PC User Guide Creating voice messages 1 Open HP SmartCalendar. 2 Press Record Note at the bottom of the screen. 3 Press the Record
maximum). 4 Press the Stop button to stop recording your message. button to record a short message (120 seconds 5 Press the Play button to listen to your
message.
6 Press Done when you are finished. Your voice note appears with a speaker next to your calendar. Voice notes can be played back by touching the note,
selecting the microphone icon, and then pressing the Play button. NOTE: If you move a copy of a voice note to your HP SmartCalendar, you cannot listen to
the message from the calendar view. You can only play voice notes from the bulletin board. Moving notes to your calendar When you create a note you can
copy it to a specific date on the calendar by dragging the note to a date. It then appears as a Reminder on the date you selected. To view the note, press the
date, and then press the reminder. NOTE: Once you move a copy of your notes to the calendar, you cannot edit them. You must edit notes from the bulletin
board and then drag a copy of the new note to the calendar date.
Editing notes When your notes appear next to the calendar, you edit them. Just press them to open them in the create a note window. Once you move your
notes to the calendar, they can no longer be edited. Deleting text and voice notes 1 Open HP SmartCalendar. 2 Press the note you want to delete and drag it
to the wastebasket icon in the HP SmartCalendar page. Using the HP TouchSmart PC 33 Using HP Photosmart Touch With HP Photosmart Touch you can
upload, view, edit, and print your digital memories with the touch of a finger. The easy-to-use touch display lets you view and print photos as easily as using a
photo kiosk. You can use the accessible card readers on the front of the HP TouchSmart PC to easily upload photos from your digital camera. You can also
add an HP photo printer (A510 Series and A610 Series) where your photos print out right under the display. Opening HP Photosmart Touch To open your HP
Photosmart Touch: 1 Open the HP SmartCenter page.
2 Press the HP Photosmart Touch icon. Transferring your photos to the PC You can transfer digital images and videos to the HP TouchSmart PC by using
various methods.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
HP Photosmart Touch can import photos that are located in any device that is listed as Volume drive in Computer or Device Manager. If your device is not
listed as a Volume drive, you must move your photos to a folder on your computer for HP Photosmart Touch to be able to find, display, edit, and print them.
To transfer photos to your PC: 1 Insert a memory card into the memory card reader.
a Or b Insert a photo CD or DVD disc into the DVD drive. 2 Move your pictures to a PC folder, such as Pictures, or to your desktop. Connect a digital
camera or digital video camera to the HP TouchSmart PC with the transfer cable that came with the device. (Select models have a digital camera docking
bay.) Working with digital images You can connect a digital image source, such as a digital photo or video camera, directly to the HP TouchSmart PC or
through a docking station.
Most digital picture files you copy or download from the device appear in the Pictures folder. NOTE: When transferring pictures from a digital photo camera
to the HP TouchSmart PC in HP Photosmart Touch, set the camera's USB setting to disk drive instead of digital camera. Windows Vista detects your external
device and displays a message asking if you want to view your images. You can copy digital picture files from the memory cards used by digital cameras and
other digital imaging devices by using the memory card reader (select models only). 34 HP TouchSmart PC User Guide HP Photosmart Touch shortcuts
Select the shortcut icons on the HP Photosmart window to perform the following tasks. HP Photosmart Touch Main Window Button or Toolbar Function
Refresh the HP TouchSmart PC for any new photos that were added to your hard disk drive. Import your pictures from a camera, a memory card, or from a
folder on your hard disk drive. Print your photos, photo packages, and index sheets using the images you select. Return to the main HP SmartCenter window.
Enlarge or reduce the viewing size of your photos.
Adding pictures to your HP Photosmart Touch library The first time you open the HP Photosmart Touch program, a message appears asking if you want to
create a library by finding images on your HP TouchSmart PC. 1 Open HP Photosmart Touch. 2 Connect your photo device or insert your media. Insert a
memory card, external hard disk drive, CD, DVD, or digital camera. 3 Press the Import photos icon. 4 Press From Folder, and browse to where your photos
are located. 5 Select a folder to import, and place a check mark next to folder you want to import. 6 Press OK. 7 Press the Refresh icon to update your HP
Photosmart Touch library with any new photos that have been added to your hard disk drive. Using the HP TouchSmart PC 35 Searching for pictures with
HP Photosmart Touch You can search for pictures by date or tag in HP Photosmart Touch based on the date assigned by the camera when the picture was
taken or the date the picture was scanned.
1 Open HP Photosmart Touch. 2 Press Date. Select the date of your picture. Use the scroll bar on the right to view all of the photos, if necessary. Or Press
Folder.
Select a folder, and then select the photos you want to view. 3 Use the scroll bar to find your pictures which are listed by the date they were added to your
hard disk drive. 4 Press the Refresh icon to update your HP Photosmart Touch library with any new photos that have been added to your hard disk drive.
Selecting pictures in HP Photosmart Touch You can view all of your images, individual albums, or pictures selected from a search. 1 Open HP Photosmart
Touch.
2 Navigate to the group of pictures you want to view. 3 Touch the circle on the left side of the thumbnail image to select it for printing. A check mark appears
when the photo is selected. Editing pictures in HP Photosmart Touch You can make changes to your pictures in HP Photosmart Touch. Some of the editing
features include removing red-eye, cropping, and rotating images. 1 Open HP Photosmart Touch. 2 Click anywhere on a photo (except on the circle on the
left) to select it. When you select a photo, the HP Photosmart Touch editing window opens. 36 HP TouchSmart PC User Guide 3 Select the editing option,
such as Crop. 4 Select your cropping option of Landscape, Portrait, or Custom, press and drag the cropping arrows until you have the cropped image you
want, and then select Apply.
5 Press Done. NOTE: You may need to refresh the window to view your edited picture in your HP Photosmart Touch folders. Printing pictures in HP
Photosmart Touch You need to connect your printer and install any printer software before you can print from HP Photosmart Touch. 1 Open HP Photosmart
Touch. 2 Select the photo you want to print by clicking the bottom-left corner. A check mark is displayed when a photo is selected. 3 Press the Print icon at the
bottom of the window. Using the HP TouchSmart PC 37 4 Select your print options, and then press Print. 5 Follow any onscreen printing instructions. Other
HP SmartCenter Features Personalizing your HP SmartCenter page To change the look of your HP SmartCenter page: 1 Open the HP SmartCenter page.
2 Press or click the Personalize 3 Select the Appearance tab. icon. 4 Select your HP SmartCenter page settings: Under Opening Screen Animation, select
Show or Hide. Under Button Annimation, check or uncheck Ripple or Bounce. Under Optimize Windows for Touch, select Touch Optimized or Mouse
Optimized.
Under Theme Color, select a color. 5 Press the Back to HP SmartCenter icon when you are finished. 38 HP TouchSmart PC User Guide Changing what you
can launch from HP SmartCenter 1 Open the HP SmartCenter page. 2 Press or click the Personalize 3 Select the Arrange Programs tab. 4 Click and drag the
shortcut icon you want to move over another shortcut icon.
When you let go, the shortcuts change position on your HP SmartCenter page. icon. 5 Press Back to HP SmartCenter when you are finished. Adding or
removing a Web shortcut on the HP SmartCenter page 1 Open the HP SmartCenter page. 2 Press or click the Personalize 3 Select the Select Programs tab.
icon. 4 Select the shortcuts you want to appear by placing or removing the check mark next to each item listed. Use the scroll bar on the right side of the
screen to view all of the shortcut items. NOTE: Up to twelve and a minimum of three shortcut icons appear on the HP SmartCenter page at one time. Using
the HP TouchSmart PC 39 5 To create a new shortcut, place a check mark next to Create a shortcut for your favorite program or web site, and then press
Create Shortcut Change on the right side of the screen.
6 Select Web Page. 7 In the address field, press the touch keyboard icon to enter the Web address by touch, or you can use your physical keyboard to enter the
address. 8 Enter your shortcut name. 9 Select an icon for your Web page shortcut. 10 Press OK. 11 Press Back to HP SmartCenter when you are finished.
Adding or removing a program shortcut on the HP SmartCenter page 1 Open the HP SmartCenter page.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
2 Press or click the Personalize 3 Press the Select Programs tab. 4 Select the shortcuts you want to appear or remove by placing or removing the check mark
next to each item listed. NOTE: You can have up to twelve and a minimum of three shortcut icons at one time.
5 To create a new shortcuts, press Create Shortcut Change. 6 Press Program. 7 Press Browse to locate a program you want to create a shortcut for, select it,
and then press OK. 8 Press Back to HP SmartCenter when you are finished. icon.
40 HP TouchSmart PC User Guide Using the touch screen to access Windows Media Center You can enjoy your favorite music, TV programs, slideshows,
and movies by using Windows Media Center. All of the menus in Windows Media Center are accessible through touch as well as your remote control,
keyboard, and mouse. It is your choice. To open Windows Media Center from the Start menu just press the Windows Start Button on the taskbar, and then
press Windows Media Center. To open Windows Media Center from the HP SmartCenter just open HP SmartCenter and press the Windows Media Center
icon.
To open HP SmartCenter: 1 Press the Windows Start Button on the taskbar. 2 Press All Programs. 3 Scroll down the Start menu, and then press HP. 4 Press
HP TouchSmart Programs. 5 Press HP SmartCenter. For more information about using Windows Media Center, refer to the Getting Started guide. Some of
the things you can do in Windows Media Center are: Use the included remote control or touch screen to quickly and easily access your music, TV programs,
movies, and radio. Watch TV programs and movies. Browse and listen to your music collection. Play DVDs and videos.
Listen to FM and Internet radio. Create music CDs and DVDs of your recorded TV programs. Opening HP SmartCenter from Windows Media Center 1 Click
the Windows Start Button on the taskbar. 2 Click Windows Media Center. 3 From the Windows Media Center menu, scroll to HP TouchSmart Programs, and
then select HP SmartCenter, HP SmartCalendar, or HP Photosmart Touch. Using the HP TouchSmart PC 41 Access PC updates, PC health and security
information, and more with HP Advisor HP Advisor is available in North America only. 1 Press or click the Windows Start Button 2 Click HP Total Care
Advisor. Or Press or click All Programs, scroll down the Start menu, and then press or click HP. Press or click HP TouchSmart Programs. Press or click HP
SmartCenter.
3 Click the HP Advisor icon. on the taskbar. 4 From here you can: View security information such as Windows Auto Update and Virus Protection. Get PC
updates. Connect to the Internet and view Internet Service Provider offers.
View HP warranty information. View connected printers and add a printer. Launch Microsoft Backup Tool. Access PC health and security information.
Access PC help tools.
Access PC Action Center, where you can get critical PC alerts, tips, and tricks regarding keeping your PC in good working order. 42 HP TouchSmart PC
User Guide Using Tablet PC software to enter text with the touch screen Use Microsoft Tablet PC to enter text in any software program or Internet text field
without using the keyboard. You can use the stylus or your touch to enter text on the touch screen by using the onscreen keyboard. Use the writing pad or the
character pad to convert your handwriting into typed text, or use the onscreen keyboard to enter characters. To open the Tablet PC Input Panel: 1 Press the
Windows Start Button on the taskbar. 2 Press All Programs, Accessories, Tablet PC, and then Tablet PC Input Panel. 3 To move or dock the window to the
side of your screen, just press the close button. 4 To move it back to the middle of the desktop, just touch and press it. 5 Use your stylus or your touch to write
a note. You can also use the tools in the Windows toolbar to customize your note Using Windows Journal software to create hand-written notes and drawings
Use Windows Journal to write or draw using your stylus on the touch screen.
You can save your handwriting in a note, convert the writing to type-written text, or just leave your handwriting or drawing as ink in a note. You can also
insert pictures into your notes. To open the Windows Journal: 1 Press the Windows Start Button on the taskbar. 2 Press All Programs, Accessories, Tablet
PC, and then Windows Journal. 3 Use your stylus or your touch to write a note or draw a picture. You can also use the tools in the Windows Journal toolbar
to customize your note. 4 To save your note, press the File menu and press Save. Using the HP TouchSmart PC 43 44 HP TouchSmart PC User Guide
Upgrading the HP TouchSmart PC Safety Information This product has not been evaluated for connection to an "IT" power system (an AC distribution system
with no direct connection to the earth, according to IEC 60950). WARNING: Please read "Additional Safety Information" in the Limited Warranty and
Support Guide before installing and connecting your system to the electrical power system. Opening and Closing the HP TouchSmart PC Vertical cover Rear
cover Preparing the HP TouchSmart PC Before you upgrade any component in your HP TouchSmart PC, you need to prepare the HP TouchSmart PC so that
you can safely handle it and the components.
Read the following items before attempting to upgrade or service the HP TouchSmart PC. 1 These procedures assume familiarity with the general
terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic
equipment. 2 Write down and save the system model and serial numbers, all installed options, and other information about the system. It's easier to consult
this information than to open and examine the computer. Upgrading the HP TouchSmart PC 45 3 It is recommended that you use an antistatic wrist strap and
a conductive foam pad when working on the system.
WARNING: Always disconnect the HP TouchSmart PC from the power source before removing the rear or vertical cover of the HP TouchSmart PC. Failure
to do so before you open the HP TouchSmart PC or do any procedures can result in personal injury or equipment damage. Before opening the HP
TouchSmart PC To avoid injury and equipment damage, always follow this procedure in this order before opening the HP TouchSmart PC. 1 Remove any
media (CD, DVD, memory cards, USB devices, external hard disk drives) from the HP TouchSmart PC. 2 Click the Windows Start Button, and then click Shut
Down.
CAUTION: To reduce the risk of personal injury from electrical shock or hot surfaces, disconnect the power cord from the wall outlet, and allow the internal
system components to cool before touching. 3 Disconnect the power cord from the electrical outlet and then from the HP TouchSmart PC. 4 Disconnect all
other attached cables from the rear of the HP TouchSmart PC. 5 Disconnect all external devices. CAUTION: Static electricity can damage the electronic
components of the HP TouchSmart PC or optional equipment.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
Ensure that you are discharged of static electricity by briefly touching a grounded metal object. After closing the HP TouchSmart PC To avoid injury and
equipment damage, always follow this procedure in this order after closing the HP TouchSmart PC. 1 Reconnect the power cord. WARNING: To reduce the
risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the network interface card (NIC)
(labeled as LAN). 2 Reconnect all other cables.
3 Reconnect external devices. 4 Turn on the HP TouchSmart PC and all peripherals such as the monitor. 46 HP TouchSmart PC User Guide Removing the
rear cover This procedure is necessary when removing and upgrading memory. 1 See "Opening and Closing the HP TouchSmart PC" on page 45. 2 Remove
the two screws that secure the rear cover to the HP TouchSmart PC chassis. Keep the screws for later. + - 3 Pull the rear cover back about 1/2 in (1.27 cm)
(A). If necessary, gently push down on the cover while pulling back. 4 Lift the rear cover and remove from the chassis (B).
WARNING: Beware of sharp edges inside the chassis. Upgrading the HP TouchSmart PC 47 Replacing the rear cover 1 Place the rear cover in the proper
position on the chassis and about 1/2 in (1.27 cm) back from the vertical cover. 2 Slide the rear cover toward the front of the chassis until the rear of the cover
is flush with the rear I/O area of the chassis. 3 Ensure that the holes for the screws align with the holes in the chassis, and then replace the two screws.
Removing the vertical cover This procedure is necessary when removing or replacing the hard disk drive. 1 See "Opening and Closing the HP TouchSmart
PC" on page 45. CAUTION: To reduce the risk of personal injury from electrical shock or hot surfaces, disconnect the power cord from the wall outlet, and
allow the internal system components to cool before touching. 2 If necessary, raise the display (monitor) until the pocket behind the monitor is accessible. 3
While holding the back of the vertical cover, push and hold down the lever on the front of the vertical cover.
This lever is located in a pocket behind the display (monitor) portion of the HP TouchSmart PC. Lever 4 While holding down the lever, pull the vertical cover
up and remove from the chassis. 48 HP TouchSmart PC User Guide Replacing the vertical cover 1 Align and insert the hooks on the vertical cover into the
holes on the back of the chassis. 2 Reach behind the display, and hold down the lever on the vertical cover while sliding the vertical cover down and into
place on the back of the vertical chassis. Adding Memory Your HP TouchSmart PC comes with random access memory (RAM), which temporarily stores data
and instructions on your HP TouchSmart PC. The HP TouchSmart PC ships with two memory modules, but you can replace the existing memory modules with
higher-capacity ones. The motherboard contains sockets for SO-DIMMs (small outline dual in-line memory modules). To determine which type and speed of
memory module your HP TouchSmart PC uses, and for specific memory module information and specifications, go the Web site listed in your Limited
Warranty and Support Guide, and click the Support link. WARNING: Using the wrong type of memory module could damage the system. Removing a memory
module 1 Complete the procedures to prepare the HP TouchSmart PC and to remove the rear cover.
See "Opening and Closing the HP TouchSmart PC" on page 45. 2 Remove the cable from the DVD drive. DVD drive Tab DVD drive cable 3 Lift the tab at the
left side of the DVD drive and slide the drive straight back. 4 Move the DVD drive cable away from the memory module beneath it. CAUTION: When
handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module. Upgrading the HP TouchSmart PC 49 WARNING:
Do not pull the memory module out of the socket. Use the latches of the retaining clips to remove the module. 5 Push the two latches of the retaining clips
away from the memory module. The memory module pops up at an angle.
Latches Latches Memory module 6 Lift the memory module from the memory socket. Note the location of the key slot on the connector edge. Installing a
memory module Upgrade the memory in your HP TouchSmart PC with memory of the same type and speed as the memory originally installed in your HP
TouchSmart PC. @@@@NOTE: The sockets are keyed. @@@@3 Push the outer edge of the memory module down until the retaining clip latches catch.
4 Move the DVD cable out of the way and insert the DVD drive. Slide the drive in until the tab catches. 5 Reconnect the DVD drive cable. 6 Complete the
procedures to replace the rear cover, and close the HP TouchSmart PC. See "Opening and Closing the HP TouchSmart PC" on page 45.
NOTE: If a blank screen is displayed after replacing or adding a memory module, the memory is installed incorrectly or it is the wrong type of memory.
Remove and reinstall the memory module. 50 HP TouchSmart PC User Guide Removing and Replacing the Hard Disk Drive You can replace or upgrade the
hard disk drive. @@Failure to do so may result in data loss. @@@@See "Opening and Closing the HP TouchSmart PC" on page 45. @@4 Lift the cage up
off the two bottom screws and out of the chassis. 5 Disconnect the power and data cables from the back of the drive. Squeeze the latch on the SATA connector
to remove the data cable. 6 Remove the four screws from the cage, and lift the sides of the hard disk drive from the cage. Screws Upgrading the HP
TouchSmart PC 51 Replacing the hard disk drive 1 Complete the procedures to remove the hard disk drive, if necessary.
See "Removing the hard disk drive" on page 51. 2 Place the hard disk drive into the cage and insert the four screws. Screws 3 Connect the power and data
cables to the hard disk drive. 4 Place the hard disk drive cage over the two bottom screws and into the chassis. Screw (insert) Screw (insert) Power cable
Data cable Screw (tighten) Screw (tighten) 5 Insert the two top screws and tighten the two bottom screws. 6 Complete the procedures to replace the vertical
cover and close the HP TouchSmart PC. See "Opening and Closing the HP TouchSmart PC" on page 45. 52 HP TouchSmart PC User Guide Locating
Information About Your Computer This section is an index to information about your computer. The information is located in this guide and other guides that
have been included with your computer. HP TouchSmart PC User Guide (this guide), a printed guide with specific information about the HP TouchSmart PC
product.
References are listed as black page numbers UG-#. Getting Started guide, included on your computer is an onscreen guide, provides information about using
your HP computer, the Microsoft Windows Vista operating system, the Windows Media Center, and some of the hardware and the software programs
included with the computer.
You're reading an excerpt. Click here to read official HP touchsmart
iq700 user guide
http://yourpdfguides.com/dref/886525
Powered by TCPDF (www.tcpdf.org)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising