How to configure VLAN - D-Link

How to configure VLAN - D-Link
How to Configure VLAN
This example requires a DFL-1600 or 2500 to be fully implemented. Most settings can
however also be used on a DFL-210 or DFL-800.
Two tag based VLANs will be created on lan3, that connect to switch port with VLAN tag.
Details:
- From lan1, lan2 and lan3: HTTP, HTTPS and DNS connect to Internet via wan2.
- All internal nets can also access the Mail server in dmz.
- Only VLAN2 can access the FTP server in dmz.
1. Addresses
Go to Objects -> Address book -> InterfaceAddresses
Make sure the configured addresses match the following list, and add the objects that not
already exist. To add new objects, select IP address from the add dropdown, enter name and
address and click ok.
Name
Address
lan1_ip
192.168.1.1
lan1net
102.168.1.0/24
lan2_ip
192.168.2.1
lan2net
192.168.2.0/24
lan3_ip
192.168.3.1
lan3net
192.168.3.0/24
dmz_ip
172.17.100.254
dmznet
172.17.100.0/24
wan1_ip
192.168.110.1
wan1net
192.168.110.0/24
wan1-gw
192.168.110.254
wan2_ip
192.168.120.1
wan2net
192.168.120.0/24
wan2-gw
192.168.120.254
vlan1_ip
192.168.5.254
vlan1net
192.168.5.0/24
vlan2_ip
192.168.10.254
vlan2net
192.168.10.0/24
ftp-server
172.17.100.1
mail-server
172.17.100.2
Add a new IP4 Group.
In the General tab:
General:
Name: all-lannets
Add lan1net, lan2net, vlan1net and vlan2net.
Click Ok.
2. Ethernet interfaces
Go to Interfaces -> Ethernet.
Edit the wan1 interface to use the following settings.
In the General tab:
IP Address: wan1_ip
Network: wan1net
Default Gateway: wan1_gw
In the Advanced tab:
Automatic Route Creation:
Deselect Add route for interface network and Add default route if default
gateway is specified.
Click Ok.
Edit the wan2 interface according to the following settings.
In the General tab:
General:
IP Address: wan2_ip
Network: wan2net
Default Gateway: wan2_gw
In the Advanced tab:
Automatic Route Creation:
Deselect Add route for interface network and Add default route if default
gateway is specified.
Click Ok.
3. Routes
Go to Routing -> Routing Tables -> Main.
Add a new Route.
In the General tab:
General:
Interface: wan1
Network: all-nets
Gateway: wan1_gw
Local IP Address: (None)
Metric: 90
Click Ok.
Add a new Route.
In the General tab:
General:
Interface: wan2
Network: all-nets
Gateway: wan2_gw
Local IP Address: (None)
Metric: 80
Click Ok.
4. VLAN interfaces
Go to Interfaces -> VLAN.
Add a new VLAN.
In the General tab:
General:
Name: vlan1
Interface: lan3
VLAN ID: 1
Address Settings:
IP Address: vlan1_ip
Network: vlan1net
Default Gateway: (None)
Click Ok
Add a new VLAN.
In the General tab:
General:
Name: vlan2
Interface: lan3
VLAN ID: 2
Address Settings:
IP Address: vlan2_ip
Network: vlan2net
Default Gateway: (None)
Click Ok
5. Interface groups
Go to Interfaces -> Interface Groups.
Add a new Interface Group.
General:
Name: all-lan
Interfaces:
Add lan1, lan2, vlan1 and vlan2 to this group.
Click Ok.
Add a new Interface Group.
General:
Name: all-wan
Select Security/Transport Equivalent
Interfaces:
Add wan1 and wan2 to this group.
Click Ok.
6a. Rules to allow HTTP, HTTPS and DNS to Internet
Go to Rules -> IP Rules.
Add a new IP Rule (to allow outgoing HTTP).
In the General tab:
General:
Name: allow-http-all
Action: NAT
Service: http-all
Address Filter:
Source interface: all-lan
Source network: all-lannets
Destination interface: all-wan
Destination network: all-nets
Click Ok.
Add a new IP Rule (to allow outgoing dns).
In the General tab:
General:
Name: allow-dns-all
Action: NAT
Service: dns-all
Address Filter:
Source interface: all-lan
Source network: all-lannets
Destination interface: all-wan
Destination network: all-nets
Click Ok.
6b. Rules to allow internal users to access mail server
Add a new IP Rule (to allow internal smtp traffic to mailserver).
In the General tab:
General:
Name: allow-smtp-int
Action: Allow
Service: smtp
Address Filter:
Source interface: any
Source network: all-nets
Destination interface: dmz
Destination network: mail-server
Click Ok.
6d. Rules to allow traffic to FTP server from vlan2
Add a new IP Rule folder called vlan2_to_dmz.
Add a new IP Rule (to allow ftp from vlan2 to dmz).
In the General tab:
General:
Name: allow-ftp
Action: Allow
Service: ftp-passthrough
Address Filter:
Source interface: vlan2
Source network: vlan2net
Destination interface: dmz
Destination network: dmznet
Click Ok.
Save and activate the configuration
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising