Monster Truck Racing Association Safety Manual

Monster Truck Racing Association Safety Manual
I
nt
er
nat
i
onal
SAFETY RULES
Ver
si
on 22.
1
Copy
r
i
ght2010MTRA®MTRAE®
All Rule changes from previous
Version are highlighted in yellow
European language variations and
Metric conversions are in brackets [ ].
Nomenclature
(Abbreviations & acronyms)
CDL:
Commercial Drivers License
Competitor:
Driver
D.O.M.:
Drawn Over Mandrel
Kill Switch:
Switch that shuts off the engine
Mfg:
Manufacturer
MTRA:
Monster Truck Racing Association
est
.1
987
I
nt
ernat
i
onal
MTRAE:
Monster Truck Racing Association Europe
Participant:
Owner/driver, crewmember
R-T:
Ride truck
Race:
A contest between one or more vehicles
RII:
Remote Ignition Interrupt
SFI:
Safety Foundation, Inc.
SPEC:
Specification
MTRA
EU (European Union) Nomenclature
AFFF:
CDS:
Kg:
KPH:
£:
M:
Mm:
Aqueous Film Forming Foam
Cold Drawn Steel (same as DOM in the US)
Kilogram
Kilometers per hour
EU pounds
Meters
Millimeter
2
INDEX
PAGE
4
4
Introduction
Drug Statement
Competition Trucks
Section A
Drivers License
Driver & Crew
Remote Ignition Interrupter
Vehicle
Drivers Compartment
Seatbelt mounting
Figure 1
Rollcage
Rollcage X Brace
Figure 2
Rollcage Tube Repair
Figure 3
Rollcage Side views
Figure 4/5
Engine
Throttle Toe Strap
Figure 6
Transmission
Mech. Clutch Vehicles
Bellhousing
Figure 7
Driveline
Drive shaft
Loops
Figure 8
est
.
1
987
DS loop location
Figure 9
Slip-yoke
Figure 10
Brakes
Rule Violations
MTRA
5
6-7
8-9
10-12
13-15
14
16-18
16
16
17
19-20
19
21-22
22
21
23-25
23
I
nt
ernat
i
onal
23
24
26
27
MT Ride Trucks
Section B
Introduction
MTRA Drivers License Driver Min. Requirements
Driver & Crew
Ride Truck Driving Rules
Vehicles - Drivers Compartment
OEM Rollcage
Figure 2B
Rollcage
Fiberglass Body Rollcage
Figure 3B
Fiberglass Body Rollcage
Figure 4B
Engine - Transmission
Driveline - Brakes
Rule Violations
28
28-29
29
30
31
33
33-34
33
33
35
36-37
38
Miscellaneous
Section C
Protest Procedures
Directors
Useful information
Vehicle/Driver Specifications Reference check list
Rule revision and suggestion list
Quick Reference inspection check list
Chaindrive Transfercase
Bolt grade spec. – Blower overdrive legal sizes
Blower overdrive legal sizes
39
40
41
42-43
44
45-46
47-48
49
50
3
INTRODUCTION
The purpose of the Monster Truck Racing Association is to provide consistent safety for
competitors and spectators. MTRA makes no expressed or implied warranties of safety
from publication of or compliance with these rules and regulations. They are intended as
a guideline for the conduct of the sport and are in no way a guarantee against injury or
death to participants or spectators.
Perfect adherence and application of the rules published by MTRA will not assure that all
vehicles will perform all safety applications. The individual fabricator and driver have the
ultimate control of how the Monster Truck is constructed and operated.
Using MTRA rules does not imply that all safety measures are included. MTRA or its
representatives assume no liability whatsoever.
MTRA
Any vehicle component not included in these rules or any deviation from these rules will
est
.1
987
I
nt
ernat
i
onal
be subject to director's
written approval.
It is the responsibility of the participant(s) to familiarize his/herself with all MTRA rules.
DRUG STATEMENT
The Monster Truck Racing Association (MTRA) strives to create and maintain a healthy
environment for all people involved in monster truck related events.
A healthy environment is one in which the use of alcohol and/or drugs does not interfere
with the safety and performance of MTRA members. Drugs include all illegal drugs and
any and all prescription and/or over-the-counter medications that can affect a person’s
ability to operate machinery.
These uses place the lives and well being of monster truck participants, event staff and
spectators at risk of accidents, injuries, and even death.
It is the duty of all members of the MTRA to take responsibility for preventing the
dangerous use of alcohol and/or other drugs from adversely affecting the monster truck
community.
4
Section A
Competition Trucks
MTRA® DRIVER LICENSE
All MTRA drivers must have a valid MTRA Drivers License. This license must be
checked prior to each event.
A Class “A” driver license is required when driving in a Certified Points or Purse Race
Series and a Class “B” for all other types of performances.
Driver member will submit the normal MTRA dues and a copy of their current CDL or
CDL equivalent physical when applying for their yearly MTRA Driver License or Drivers
License renewal.
est
.1
987
MTRA
I
nt
ernat
i
onal
CLASS “A” DRIVERS LICENSE
Class “B” Drivers must execute 10 performances, in a MTRA Certified Vehicle,
witnessed by at least one MTRA Class “A” driver at each performance. The final
application must have at least 3 different Class “A” Driver signatures, (you cannot have
one driver sign all 10 performances). The MTRA Board of Directors will then evaluate
the application and decide whether to issue the license or to require more tests. As a
Class “A” driver it will be your duty to watch Class “B” drivers and evaluate their driving.
It would be a good idea to give constructive criticism.
CLASS “B” DRIVERS LICENSE
New drivers will have to perform a prescribed driving test, in an MTRA Certified Vehicle,
with 3 MTRA Class “A” Drivers present. The driving test will consist of an in cab
familiarity test, vehicle parking, stopping and turning demonstration, and then driving
over cars several times at different speeds. The Class “A” Drivers must endorse this
performance. The application must then be sent to the MTRA Board of Directors for their
approval or disapproval.
5
DRIVER & CREW
1.
A current CDL or CDL equivalent [Europe HGV medical required] physical is
required and a copy must accompany each year’s application for an MTRA Driver
License renewal. Current physical means a physical at least every (2) two years.
2.
All MTRA drivers will be subjected to a random Drug testing. If their name is
picked, they will be informed and will be given 48 hours to comply with the drug test
at one of the 2500 test stations across the country. An independent agency will
randomly pick driver names. Non-compliance will be considered an admission of
guilt and their MTRA Drivers License and Membership will be canceled. Drivers can
be called for drug testing more than once a year.
3.
Approved helmets are mandatory. All competitors must use an (new spec.) SFI
31.1 full or open face helmet or (old spec.) SFI 31.2A (Snell SA) rated full-face
helmet or SFI 31.1A (Snell SA) rated open-face helmet. (SA = Special Application
Nomex lining Competition Helmet), SA2000 SNELL rated helmet are also legal. SFI
41.2, SFI 41.1 or SNELL M, motorcycle helmets are not allowed. MTRA
recommends helmet restraints. (Straps from underarms to sides of helmet.) Fullface helmets are highly recommended. Helmets must be sent back to the
manufacturer for re-inspecting after being dropped or hitting any hard object.
est
.1
987
MTRA
I
nt
ernat
i
onal
(In 2005 the new SFI helmet specs are combining open and closed face helmets to
31.1 for Flame Resistant Motorsports Helmets and 41.1 for Motorsports Helmets
(non-flame resistant). The new spec will also have a year of the current specs and it
will change every 5 years. New helmet must be a SFI 31.1; the 41.1 will not be legal
for a Monster Truck Driver.)
4.
Eye protection is required during performances. Goggles and helmet shields that
are approved for motor sports competition are recommended Windshields are
always required.
5.
Approved Motor sport neck collars are required unless the driver is wearing a
Hans or similar Device.
6.
A Multi-layer fire retardant safety suits with a SFI rating of 3-2A/15 and shoes and
gloves with a SFI rating of 3.3/5 are required at all times. No tennis shoes allowed.
MTRA recommends the use of a head sock when running on Methanol (Alcohol).
7.
Drivers must operate vehicles in a safe manner at all times. The show or race
director has the right to stop and disqualify any driver not operating his or her
vehicle in a safe manner.
7b) Vehicles should not drive over 5MPH except during performances.
7c) Anytime the engine is running a participant should be in the drivers’ seat with
complete control of the vehicle.
6
8.
All contestants and the pit crew must be clean, neat and professionally attired
when appearing before the public.
9.
Drivers must be at least 18 years old, or be approved by the MTRA Board and
have parental or guardian written permission.
10. No one is allowed in the performance area during an event, except track officials
and a minimum number of crewmembers.
11. Before an MTRA member can perform, the exhibition area must be cleared of all
spectators and participants.
12. Drivers must, at minimum, have a seatbelt on at all times the vehicle is moving
with 66” tires.
13. The driver has the final decision on whether he or she can perform the race or
exhibition in a safe manner. MTRA will back the driver 100% if he or she cannot
fulfill his or her contractual agreement because of a safety reason.
14. Consumption of intoxicating agents or drugs before or during an event by a
driver or his or her pit crew will be grounds for disqualification of driver. If the driver
is found violating this rule he or she is subject to suspension from MTRA.
est
.1
987
MTRA
7
I
nt
ernat
i
onal
REMOTE IGNITION INTERRUPT (RII)
MTRA initiated and then required the use of RII’s on all Monster Trucks to
enhance the safety of Spectators and Participants.
RII’s, (Remote Ignition Interrupter), must be tested by a qualified operator prior to the car
crush or exhibition. This makes sure the driver has his receiver on and switched to the
correct channel. This also gives the RII operator a chance to depress the button on the
transmitter and see how easy it is to stop the vehicle. The Monster Truck will not run if
the (RII) is not on. The RII is required first to protect the spectators, second to protect the
participants, and third to protect the driver.
15. RII receivers and transmitters are required on all Monster Trucks. (“RII” denotes
Remote Ignition Interrupt)
16. RII’s must be setup so the engine will not operate unless the RII is on.
17. MTRA members cannot participate in an event unless all vehicles involved,
within the Monster Truck portion of the performance or race, are equipped with
RII’s in working order.
MTRA
18. RII’s mustebe
tested
before the event and each round
ofr
aa
race,
st
.
1
987
I
nt
e
n
t
i
onoral
performance.
19. Anytime a vehicle moves above idle speed, a qualified operator must control
the RII transmitter. This includes testing; show introductions, race return-lane
time, parade laps, etc.
20. RII’s must always be switched to the Right channel. Only when performing or
racing in the Left lane can the switch be set to the Left channel. After racing or
performing in the left lane the RII must be switched back to the RIGHT channel.
If you have a Center RII channel, it can only be used when a promoters RII
transmitter is not present and your RII transmitter is used.
21. MTRA recommends one person for each RII; this means one qualified RII
operator controlling each vehicle.
22. Anyone altering or bypassing the RII receiver will be suspended. Resetting of
RII after being stopped, before the RII operator or official gives you permission to
start, is the same as bypassing and is subject to suspension.
23. The RII Light must be on or above the dash and visible to the track official in
front of the vehicle. It must be an Auto Meter Pro Light or an equivalent light,
approved by MTRA Board, with a red lens. When applicable a second light will
be a lane indicator, right is red and left is yellow. The new Audiax RII comes with
both Pro Lights. The lights must be, (two feet apart minimum), mounted at least
one foot to each side of the center of the windshield.
8
24. Your RII number must be visible on the right side of the windshield or fender for
easy visibility of the race official. It must be a 2” by 2” number. Receiver
antennas must be vertically mounted.
Note for RII operators: Sometimes it is prudent for the RII operator not to stop (kill)
a vehicle when it is in an awkward situation and let the driver try to power out of that
bad situation. This can only be done when spectators and participants are not in
danger.
MTRA® RII Legal Radios
RII Radios LLC. (609) 625-3481
Audiax Radios (216) 392-6800
Motorsport Communications (866) 966-8672
[Europe only accepts]
L. A. Supertrux Ltd. +44 1327 705456
est
.1
987
MTRA
9
I
nt
ernat
i
onal
VEHICLES
25. Vehicle Certification is required before February 15th [Europe 31st March] of each
calendar year. Vehicle Certification will begin approximately 3 months prior to each
calendar year. Membership dues must be paid before Vehicle Certification decals
and Drivers Licenses will be issued. Inspectors cannot certify their own vehicles.
Vehicles must be re-inspected after sale.
26. Vehicles must be re-inspected by a MTRA Inspector after a major crash or rollover.
27. The current Certification Inspection sheet must be displayed in the vehicle at all
times. The sheet will be visible for all MTRA members and the tech officials. A
plastic sheath is recommended for protection against weather.
28. A kill switch must be mounted in the center rear of the vehicle. Maximum 6’ [2m]
high at rear most part of vehicle, (near bumper). Switch must pull to turn off, with a
2” [50mm] diameter, (.125) 1/8” [3.2mm] minimum wire ring, painted florescent red
or orange. Switch must kill engine, the same as the in-cab kill switch rule #38.
29. All vehicles must be equipped with a commercially made back-up alarm, mounted
at the rear most part of the frame. This alarm must be activated anytime vehicle is in
reverse. The shift gear lever must mechanically activate the alarm. The alarm sound
st
.1
987
I
nt
ernat
i
onal
must face e
rearward.
MTRA
30. All vehicles must be equipped with a bright light mounted on the rear of the frame.
This light must illuminate anytime vehicle is placed in reverse and must be activated
automatically by the gear shift lever.
31. Dry or gel type batteries are mandatory. Batteries must be secured and covered
with a non-conductive material. Material to be rubber, plastic or Lexan only.
32. An external crossover relief valve is required on all vehicles equipped with orbital
steering. Unit may bolt directly to orbital valve or be remotely mounted.
33. Tires must be 66x43x25 or 66x44x25 (size as marked on tire), unless agreed to by
all participants.
34. Monster Truck minimum weight is 9000 pounds [4883kg]. Weight includes driver,
fuel, water, & oil.
35. All charged gas shock remote cylinders (accumulators) must be mounted
securely in a position to avoid contact with tires. Caps to be threaded on tubes a
minimum of 1/2” SAE fine thread. Remote accumulators to be fastened with metal
clamps, no tape or wire ties.
10
36. All onboard fuel must be in an anti-spill tank/fuel cells, properly secured with a
minimum of two (2) metal straps, (.125) 1/8” [3.2mm] by 1” [25mm] steel or
aluminum, or the manufacturer’s suggested mounting points. Vent line anti-spill
valves are required. Primer fuel tanks have the same requirements as regular fuel
tanks. Vented caps are not permitted. Grounding all fuel tank cap rings when
fueling, to eliminate static charge, is recommended. MTRA recommends protection
on the bottom of plastic fuel tanks.
37. All tanks/fuel cells and valves must be located in an open area inside the
mainframe rails of the chassis. All fuel lines must be approved steel-braided or highpressure reinforced rubber.
38. A tow bar mount is required on the front and rear of all vehicles. A 2x2” [50 x
50mm] square receiver (trailer hitch type), is recommended.
39. All vehicles must be equipped with a system which will restrain each wheel in the
event of a spindle or other axle component failure. Minimum specifications for
known systems are as follows:
Cable Tether Type
‐ 3/8” Cable in choker configuration
‐ st
5/8”
Clevis
e
.1
987
I
nt
ernat
i
onal
‐ 3/8” Mounting plate on king pins
‐ 3/8” Rotor bolted (3/8” bolt minimum – all bolt holes on hub must be
used - 8 bolt minimum) or welded (360 degrees) to hub
MTRA
Fixed Disk Type
‐
‐
3/8” Rotor plate bolted (3/8” bolt minimum – all bolt holes on hub must
be used – 8 bolt minimum) or welded (360 degrees) to hub
Minimum Two capture points 180 degrees on center with minimum 55
degrees of coverage around perimeter.
11
est
.1
987
MTRA
I
nt
ernat
i
onal
IMPORTANT NOTES
Do not refuel while battery is charging.
No smoking while refueling. A fire extinguisher must be within
easy reach.
12
DRIVER’S COMPARTMENT
40. All vehicles must have an in-cab kill switch, within easy reach of the driver that
shuts off power to all electric fuel pumps, other powered accessories and ignition
system (all battery power) with the exception of electrically operated brake systems.
Driver must be able to activate it with his or her eyes closed in his or her seat-belted
driving position. It must be a push/pull type with push to turn off.
41. All vehicles must have an approved onboard fire retardant system [Europe AFFF
is mandatory] with a minimum of six (6) properly placed nozzles. A minimum five
(5) lb. [2.25kg] tank can only have two (2), three (3) nozzle outlet blocks; a 10 lb.
[4.5kg] or larger tank can have two (2) or more, three (3) nozzle outlet blocks. The
system must be tested each year. (The lines must be blown out with a liquid similar
to WD40 and the activating cable tested and lubricated.) The bottle pressure gage
and weight must meet Manufacture Specs. (A proper onboard fire system will inhibit
the fire while the driver clears the vehicle.) If the content is Halon, keep the outlet
spray away from your face; it could stop your oxygen supply. Driver must be able to
operate this valve with his or her eyes closed in his or her seat-belted position. An
es
t
.1
987
nt
ernat
i
o
nal
onboard fire
retardant
system is not required on stock I
production
cabs
with sealed
Firewalls.
MTRA
42. Vehicles must have a minimum size 2-1/2 lb. [1.125kg] Halon or ABC type [Europe
AFFF] fire extinguisher with a working gauge and an attached current inspection
certificate, (retail extinguishers have date stamped on unit) (2 year limit). The
extinguisher must also be securely mounted with a suitable quick release bracket
within the driver's reach.
43. Firewall & Windshield.
The driver’s compartment must be protected against engine compartment
flash fires. Firewall material must be a minimum (.063) 1/16” [1.5mm] Steel
or Aluminum, (.125) 1/8” [3.2mm] Polycarbonate/Lexan, or Fiberglass.
Plexiglas cannot be used. Floor protection is always required.
a)
i)
Front engine firewall: A firewall is required in front of the driver. Firewalls
must go from the floor to the roof and from the body skin on one side to the
body skin on the other side. A rear Lexan window is not required.
ii)
Rear engine firewall: A firewall is required behind the driver. The firewall
must go from the floor to the ceiling. A rear Lexan window is required.
iii) Mid engine firewall: (Under the cab engines). A firewall is required
underneath, behind, and in front of the driver. A rear Lexan window is also
required.
13
b)
Windshields are required on all vehicles at all times. Windshields can be a
minimum of (.125) 1/8” [3.2mm] Polycarbonate/Lexan. It is recommended
that smoked Polycarbonate/Lexan windshields be used to reduce glare.
Glass windshields are permitted on steel bodied vehicles but drivers must
wear eye protection.
44. Drivers must be protected from tire debris. There will be no exposed areas that
would allow the front tires to throw objects at driver or allow objects to bounce and
hit driver. Material must be a minimum (.125) 1/8” [3.2mm] Steel or Aluminum (.250)
1/4” [6.4mm] Polycarbonate/Lexan or the Fiberglass body parts. The entire floor of
the cab is also considered a tire debris area and must be protected.
45. All vehicles must have an approved 3” [75mm], 5-point harness that meets SFI
16.1, mounted to the frame or frame outrigger. Driver must wear the harness at all
times (this also includes the crotch strap). It is highly recommended that shoulder
harnesses be mounted at shoulder height to a maximum of 3” [75mm] above
shoulders. All straps must have a manufacturer date stamp on them and they
cannot be over 2 years old. Sternum straps and helmet restraints are highly
recommended.
est
.1
987
MTRA
14
I
nt
ernat
i
onal
45b
Ratchet strap seat belt that meet the SFI 16.1 are legal even thou they have a 2”
lower strap.
45c Hans, or similar device, is recommended for all drivers (there is a quick release for
the units) When using the Hans or similar device, the regular strap type head
restraint must be eliminated, the neck collar can also be eliminated.
46. All seats must be properly mounted to the frame or a frame outrigger. MTRA
recommends the drivers’ seat is in the middle on all new vehicles.
47. Driver compartment windows must be removed or down during a performance.
There must be 2 exit points from the driver’s compartment. Doors must be unlocked.
48. No fuel tanks, fuel lines, batteries, radiators or water hoses are allowed in the
driver’s compartment. Hydraulic steering lines that are located in the driver’s
compartment must be steel braided lines and must be shielded to deflect the oil,
from a line rupture, away from the driver. Shielding material must be strong enough
to deflect the oil at the full pressure. A mechanical oil pressure gauge must use
braided lines.
MTRA
49. No Nitrouse
Oxide,
Nitro Methane or any Oxygen Carriers
orr
Combustion
st
.1
987
I
nt
e
nat
i
onal
Accelerators allowed.
50. No loose objects allowed in vehicles.
51. There will be no riders allowed in a vehicle during a performance.
52. All fuel-injected engines must have a fuel shutoff valve, within easy reach of driver.
It must be marked with the direction to shut off. (Push or pull)
53. Vehicles must have operable forward and reverse gears and must be equipped with
reverse gear lockout.
54. All vehicles must be equipped with a starter interrupter switch that will allow starter
engagement only in the neutral position on a standard or Lenco transmission or park
and neutral positions on an automatic transmission. Engines cannot start in reverse
or forward gears.
55. All vehicles must be equipped with a quick release steering wheel.
15
ROLLCAGE
56. All newly constructed or reconstructed vehicles (after an accident, a major remodel
job, or being setup for racing), whether steel or fiberglass must have a minimum 2”
[51mm] diameter .120 [3.1mm] wall D.O.M. [CDS], (8) eight point one-piece
rollcage. The frame below the cage must also be a minimum 2” [51mm] diameter
.120 [3.1mm] wall D.O.M. tubing or equivalent. The driver must be protected in all
directions. No pieced, slip together or sectioned rollcages allowed unless it is a
flanged connection with minimum 4 bolts at both connecting points, for removal of
engine, or other components. It is recommended that all stress points be gusseted.
(Refer to figure’s #2 to 5)
est
.1
987
MTRA
I
nt
ernat
i
onal
All Rollcage and frame tubing repairs must be sleeved with a 6” [152mm] internal
sleeve.
16
57. All vehicles are required to have an “X” brace, [Europe recommends an “A” brace
behind drivers head for center seat trucks] extending from the frame to the upper
rollcage behind the driver. (Refer to figure #2)
58. All grand fathered steel-bodied vehicles are permitted to run a 6-point cage. They
are not allowed to race in a series or point’s race.
est
.1
987
MTRA
17
I
nt
ernat
i
onal
59. SFI 45.1 fire retardant padding is required (minimum thickness (.750) ¾” [19mm])
on roll cage tubing which is within 18” [457 mm] of driver’s helmet area above his
shoulders. An exclusion is approved for the area behind the headrest on vehicles
equipped with seats featuring head and shoulder restraints.
60. All vehicles lacking stock production doors (fiberglass doors) must have at least one
side bar no more than 2” [50mm] below the window and one side bar at floor height
to protect the driver from side impact. These bars must be parallel to the ground and
least 2” [50mm] in diameter.
est
.1
987
MTRA
18
I
nt
ernat
i
onal
ENGINE
61. All exhaust must discharge within a 10-degree angle of being straight up or
rearward at a 45 degree down angle. Exhaust cannot discharge straight down. No
rain caps. All exhaust pipes and mufflers must be securely attached.
62. All carburetors and fuel injection butterfly shafts must have dual return to idle
springs. A return to idle spring must be located on both butterfly shafts or at both
ends of a single shaft. They cannot be attached at the same location. The spring on
the throttle pedal does not count as one spring but is recommended.
63. Air cleaners are required on all injector hats
64. All throttle linkage from cab to the engine must be cable operated and must be a
positive action push pull type. Cable must not be stretched tight; it must have flex to
allow for the engine-to-cab movement.
65. Throttle toe straps are required. A “Hot Foot” open loop (refer to Fig. #6) or a
complete loop will suffice.
est
.1
987
MTRA
I
nt
ernat
i
onal
66. All supercharged vehicles are required to use aluminum blower studs and
approved blower restraints. Blower belt guards required, if needed to protect fuel
lines. Maximum 871 blowers, 10% overdrive, standard size 2-rotor 3-lobe type only.
Rotor angle not to exceed that of standard GM 71 series. No high helix, screw type
rotors or internal modifications to increase blower size. Blower rotor maximum
length 16” [406.4mm] and a 1 to 1 internal gear ratio with proper rotation.
19
Note: ALL THE MTRA LEGAL BLOWER OVERDRIVE COMBINATIONS ARE LISTED
IN THE BACK PAGE OF THIS BOOK.
67. If you want to run anything other than a single blower, a naturally aspirated engine,
or anything not defined in this book, the Board of Directors must approve it before it
can be used or demonstrated.
68. All engines must have a deflection shield on both sides of the engine block.
Shields must cover the engine block from the center of crank to the top of the block.
The heads do not have to be covered. Shield must be securely fastened with a
minimum 2 - 3/8” [9.5mm] bolts and made of aluminum or steel minimum (.250) 1/4”
[6.4mm] thick. Frame rails can serve as part of the shielding. “Tube chassis trucks
cannot use the tubes as part of the engine shield”.
69. No engine driven fans, electric fans only.
70. No cast iron or cast steel pulleys allowed on any moving part that runs at or above
the speed of the engine.
71. All vehicles, with harmonic Balancer, must have an approved steel harmonic
Balancer or
must
have a (.250) 1/4” [6.4mm] steel or aluminum
shield
es
t
.1
987
I
nt
ernat
i
ona1”
l [25mm]
wide 360 degrees around the stock Balancer, no more than 1” [25mm] away from
Balancer with minimum of 2 fingers attached 180 degrees apart so that Balancer
cannot move forward. The water pump may be used as part of shield. (Balancer
must be bolted to the crankshaft)
MTRA
72. Aluminum engine blocks will be permitted.
73. Maximum engine size is 575 cubic inches [9.422litres].
20
TRANSMISSIONS
74. Automatic transmissions must have a safety blanket with proper bellhousing straps
and it must be 18” [457mm] wide (as measured from the bellhousing to the tail
shaft), and it must meet SFI 4-1 requirements. No metal shields are allowed. It must
cover from rear of pan forward. (Label sewn on blanket.) Blankets must be in good
condition. If blanket has been in a fire, has burnt straps or has been torn, it must be
replaced. Metal shields are not allowed. Carbon Fiber shields are allowed.
Aftermarket transmission housings that are SFI approved, (without a blanket), will
be allowed. (Example: Dedenbear Superglide Transmission Cases with SFI 4.1 and
30.1certification are legal without external shields), Must be signed off by
Driver/Owner.
75. An SFI 29.1 certified flex plate is required on all automatic transmissions. There is a
3 year limit on flex plates and then they need to be sent back for re-certification.
(Dedenbear Superglide Transmission cases with SFI 4.1 and 30.1certifications are
legal without external shields.)
76. All transmission bell housings with 8” [203mm]or longer inspection hole opening
must have a 2” [51mm] wide shield covering the exposed transmission flex plate
st
.1
987
I
nt
er
nat
i
onaaminimum
l
with a maxe
distance
from the flex plate of 2” [51mm]. There
must
be
of 2
spaced mounting tabs if the opening is under 12” [305mm] and 3 spaced mounting
tabs if over 12” [305mm].
MTRA
21
MECH. CLUTCH VEHICLES
77. Lenco transmissions are required to have an explosion proof blanket. Couplers
must be shielded 360 degrees as per Jackshaft rule #83.
78. Mechanical clutch vehicles must have an SFI Spec. 6.3 approved explosion proof
bellhousing with a current SFI label affixed to it. Any change to the original unit
requires re-certification. Any Bellhousing lacking certification must be sent back to
the manufacturer for certification or disposed of. Bellhousing certification is good for
(2) two years.
79. The inspection/maintenance hole, in the bellhousing, is acceptable if made
precisely to the specifications outlined in the drawings. A clutch inspection &
maintenance hole may be cut on the back face of the housing. The hole may not be
longer than an area covering 90 degrees (no longer than 8 ½” [216mm]) of the
housing rear surface area. No part of the rotating clutch assembly may extend under
the clutch inspection & maintenance hole.
(Refer to fig. #7)
80. Clutch maintenance hole MAY NOT be welded if the original hole in the housing
was over 8½” [216mm] in length or 3½” [89mm] wide. All bellhousing holes must be
flush on the inside surface when cap is installed. (Refer to figure #7)
est
.1
987
MTRA
I
nt
ernat
i
onal
81. The cover for the inspection & maintenance hole must be at least (.250) 1/4
[6mm] thick steel and be fastened with at least twelve (12) 5/16” [8mm] Grade-8
bolts.
(Refer to figure #7)
82. An approved steel plate or billet flywheel is required. No cast iron flywheels.
83. All automotive type engines with bellhousing and clutch will run full block saver
plate between the engine and bellhousing, either a commercially available unit, or
3/16” [6mm] steel or (.250) 1/4” [6.4mm] aluminum with 5 - 3/8” [9.5mm] Grade 5 or
better bolts evenly spaced on the bottom of the bell housing.
22
DRIVELINE
84. Chain drives are allowed if they meet all of the specifications in the back of this
book.
85. Maximum distance between driveshaft loops will be 12” [305mm] with a minimum
of two loops per shaft. Maximum distance between loop and shaft is 2” [51mm].
Loop material shall be steel, no aluminum, not less than (.750) ¾” [19mm] by (.250)
1/4” [6.4mm]. If tubing is used for the loop support brackets, loops must be welded
to the tubes, bolts will not be allowed. Two tubes are required for the loop supports;
refer to drawing for minimum requirements. A minimum ½” [12mm] grade 8 bolts
and ½” [12mm] heim joint is required on all driveshaft guards. (Refer to figure #8 &
9)
est
.1
987
MTRA
23
I
nt
ernat
i
onal
86. Loops must be 360 degrees and round in shape and attached securely to the loop
supporting brackets with a minimum of two or more 3/8” [9.5mm] grade-8 bolts or
better. (Refer to figure #8 & 9)
87. Driveshaft shields or loops cannot be attached to anything rotating. (Refer to
figure #8 & 9)
88. Jackshafts (shafts shorter than 12” [305mm]) and couplers (whether on a Lenco or
automatic) must have 360-degree enclosures covering both u-joints and the shaft. It
can be 2 pieces bolted together. The material size, thickness and mounting must be
similar to the regular driveshaft loop specifications, rule #80, 81 & 82. No blankets
allowed.
89. When a coupler is completely contained (360 degrees) the distance between the
coupler and the enclosure can be up to 2” [51mm].
90. Driveshaft slip yoke must have a minimum penetration in any axle configuration,
equal to half the length of the spline in the most extended position, usually about 2”
[51mm]. All drive shaft slip yokes must have a loop similar to the drive shaft loops. It
must restrain the slip yoke if it separates from the drive shaft. Clearance not to
exceed 2” [51mm] in any direction from the slip yoke. (Refer to figure #10)
est
.1
987
MTRA
24
I
nt
ernat
i
onal
91. All drive line U-Joints will be enclosed in a 360 degree shield, a minimum of 4”
[102mm] wide, (.250) 1/4” [6.4mm] thick steel no aluminum. The shield must have
(3) three, 1” [25mm] by (.250) 1/4” [6.4mm] mounting straps. The shield should be
close enough to joints to restrain any broken parts. Joint should not be visible from
side, top or bottom. U-joints and u-bolts to be completely covered. (Refer to figure
#9)
92. Maximum distance between the U-joint and U-joint shield is 2” [51mm].
figure #9)
(Refer to
93. Non Planetary steering axles are required to have a shield covering the axle flange
or lockout hub. Minimum (.250) 1/4” [6.4mm] steel.
94. All pieced wheels must have the split ring to the inside when mounted on truck or
must have four bolts 90 degrees apart and corresponding tabs on the wheels for
attaching the ring to the wheel.
est
.1
987
MTRA
25
I
nt
ernat
i
onal
BRAKES
95. All vehicles must be equipped with foot operated hydraulic brakes in good working
order. The brakes must be able to stop the vehicle in its own length at 10 MPH
[16KPH]. If your vehicle does not have lockers, wheel brakes are recommended.
96. All rubber tired vehicles must be equipped with dual braking systems consisting of
two master cylinders with one brake pedal and individual lines running to the front
and rear brakes.
97. All track vehicles must be equipped with dual braking systems. You must have a
foot or hand operated hydraulic brake system as a backup to the normal track lever
steering and brake system.
98. Driveline brake rotors must be steel billet only. A minimum of three tabs 120
degrees apart, are required to keep the rotor from moving. Tabs are not required if
rotor is mounted on the driveshaft side of the pinion. (Steel billet rotors are solid with
no webbing or fins in center.)
(Refer to figure #9)
99. Vehicles equipped with driveline brakes are required to have the front brake
assembly mounted on the front differential. The rear can be mounted on the transfer
est
.1
987
I
nt
ernat
i
onal
case.
MTRA
26
RULE VIOLATIONS
100. If an owner, driver or member breaks a rule, he or she will be subject to a fine or
suspension.
101. If an owner, driver or member repeatedly breaks a rule or rules, (3 or more times)
he or she will be subject to a fine, suspension and or the loss of his or her MTRA
Membership and License.
102. The inspection sheets are legal rule violation reports and members will be fined
accordingly.
103. MTRA fines and suspensions will be issued by the Board of Directors after a
hearing with a 75% Director majority required for ratification. Hearings can be
carried out by mail or fax.
104. Minor rules affect the safety of the driver only. A minimum fine of $25.00 [£15.00]
for the first time violator and $50.00 [£30.00] for the repeat offender.
MTRA
105. Major rules
affect
the safety of spectators and participants. A major rule violation is
es
t
.1
987
I
nt
ernat
i
onal
subject to a maximum fine of $5000.00 [£2,800.00], up to a year suspension and or
termination of MTRA Membership and License. The amount of the fine and/or
suspension would depend on the severity of the violation and would be determined
by a majority vote of the current MTRA directors.
106. Non-safety rules do not affect the safety of the driver, spectator or participant. A
fine of $25.00 [£15.00] for first time violators and $75.00 [£45.00] for the repeat
offender.
107. All fines must be paid within 45 days or MTRA Membership and License will be
revoked. Written protest will be accepted only after the fines are paid. Membership
and License cannot be renewed unless all fines are paid.
108. Promoter Members will be notified of all Major rule violations.
27
Section B
Ride Trucks
© Copyright 2010 MTRA®
The purpose of the Monster Truck Racing Association is to provide consistent safety for
competitors and spectators. No expressed or implied warranty of safety shall result from
publication of or compliance with these rules and regulations. They are intended as a guideline
for the conduct of the sport and are in no way a guarantee against injury or death to participants
or spectators.
Perfect adherence and application of the rules published by MTRA will not assure that all
vehicles will perform
in all applications. The individualI
and
est
.safely
1
987
nfabricator
t
ernat
i
o
nadriver
l have the
ultimate control of how the Monster Truck is constructed and operated.
MTRA
Using MTRA rules does not imply that all safety measures are included. MTRA or its
representatives assume no liability whatsoever.
Any vehicle component not included in these rules or any deviation from these rules will be
subject to director's written approval.
R-T MTRA DRIVER LICENSE
All MTRA drivers must have a valid MTRA Drivers License. This license must be on
your person when driving a Monster Truck.
A Class “A” driver license is required when driving in a Certified Points or Purse Race
Series and a Class “B” for all other types of performances including Ride Trucks.
Driver member will submit the normal MTRA dues and a copy of their current CDL or
CDL equivalent physical when applying for their yearly MTRA Driver License or Drivers
License renewal.
28
DRIVER MINIMUM REQUIREMENTS
CLASS “B” DRIVERS LICENSE
New drivers will have to perform a prescribed driving test, in an MTRA Certified Vehicle,
with 3 MTRA Class “A” Drivers present. The driving test will consist of an in cab
familiarity test, vehicle parking, stopping and turning demonstration, and then driving
over cars several times at different speeds. The Class “A” Drivers must endorse this
performance. The application must then be sent to the MTRA Board of Directors for their
approval or disapproval.
R-T DRIVER & CREW
1.B
A current CDL or CDL equivalent physical is required and a copy must accompany
each year’s application for an MTRA Driver License renewal. Current physical means
a physical ateleast
every
(2) two years.
st
.1
987
I
nt
ernat
i
onal
MTRA
2.B
All MTRA drivers will be subjected to a random Drug testing. If their name is picked,
they will be informed and will be given 48 hours to comply with the drug test at one of
the 2500 test stations across the country. An independent agency will randomly pick
driver names. Non-compliance will be considered an admission of guilt and their
MTRA Drivers License and Membership will be canceled. Drivers can be called for
drug testing more than once a year.
3.B
Consumption of alcoholic beverages or drugs before or during an event by a driver
or his or her pit crew will be grounds for suspension from MTRA.
4.B
Drivers must be at least 18 years old, or be approved by the MTRA Board and have
parental or guardian written permission.
5.B
The driver and pit crew must be clean, neat and professionally attired.
29
RIDE TRUCK DRIVING RULES
6.B
Ride Vehicles must not be operated over 25 MPH [40KPH].
7.B
Engines must not be run over 3000 RPM. A rev limiter must be installed.
8.B
The Driver and all Passengers must wear their seatbelts at all times the vehicle is
moving.
9.B
Before the Ride Truck can move, the ride area must be cleared of all personnel.
10.B Vehicle must come to a complete stop before loading or unloading passengers.
11.B When engine is running the driver must remain in his seat unless a manual parking
brake is set and the automatic transmission is in park. Otherwise, engine must be
shut off each
time
the
driver leaves his seat.
es
t
.1
987
I
nt
ernat
i
onal
MTRA
12.B No Donuts (spins), no jumping (air), or other dangerous maneuvers allowed with
passengers onboard.
13.B Drivers must operate vehicles in a safe manner at all times. The show, race director
or promoter has the right to stop any driver not operating his or her vehicle in a safe
manner.
14.B Wheel lug nuts must be re-torqued periodically. (Minimum once a day)
15.B Engines must not operate & vehicle must not move unless the RII receiver is on and
a qualified operator controls the transmitter.
16.B The RII must be tested at least once a day.
17.B No smoking in vehicle.
30
R-T VEHICLES
18.B Vehicle Certification is required before February 15th of each calendar year. Vehicle
Certification will begin 3 months prior to each calendar year. Membership dues must
be paid before Vehicle Certification decals and Drivers Licenses will be issued.
Inspectors cannot certify their own vehicles.
19.B The current Certification Inspection Sheet must be displayed in the vehicle at all
times. The sheet will be visible for all MTRA members and the tech officials. A plastic
sheath is recommended for protection against weather.
20.B All vehicles must be equipped with a commercially made back-up alarm, mounted at
the rear most part of the frame. This alarm must be activated anytime vehicle is in
reverse. The shift lever must mechanically activate it. The alarm sound must face
rearward.
MTRA
21.B Batteries must
be
secured and covered with a non-conductive material. Material to
est
.1
987
I
nt
ernat
i
onal
be rubber, plastic or Lexan only. If under bed, (passenger area), they must be sealed
batteries.
22.B All vehicles must be painted and lettered with name of vehicle.
23.B An external crossover relief valve is required on all vehicles equipped with orbital
steering. Unit may bolt directly to orbital valve or be remotely mounted.
24.B All charged gas shock remote cylinders (accumulators) must be mounted securely
in a position to avoid contact with tires. Caps to be threaded on tubes a minimum of
1/2” [13mm] SAE fine thread. Remote accumulators to be fastened with metal
clamps, no tape or wire ties.
25.B All onboard fuel must be in an anti-spill tank, properly secured with a minimum of two
(2) metal straps, (.125) 1/8” [3.2mm] by 1” [25mm] steel or aluminum, or the
manufacturer’s suggested mounting points. OEM vehicles with stock configured fuel
tanks are legal. Grounding all fuel tank cap rings when fueling, to eliminate static
charge, is recommended.
26.B All ride trucks must have an adequate passenger loading ladder.
31
R-T DRIVER’S COMPARTMENT
27.B All vehicles must have an in-cab kill switch, within easy reach of the driver that
shuts off power to all electric fuel pumps, other powered accessories and ignition
system (all battery power) with the exception of electrically operated brake systems.
Driver must be able to activate it with his or her eyes closed in his or her seat-belted
driving position. It must be a push/pull type with push to turn off.
28.B Vehicles must have a minimum size 2-1/2 lb. [1.25kg] Halon or ABC type fire
extinguisher within the driver’s reach, with a working gauge.
29.B All Ride Truck Seats must have approved seatbelts, mounted to the frame or frame
outrigger.
30.B No fuel tanks, fuel lines, batteries, radiators or water hoses are allowed in the
driver’s compartment or in the passenger ride areas. Hydraulic steering lines that
are located in the driver’s compartment or passenger area must be steel braided lines
and must be shielded to deflect the oil, from a line rupture, away from the driver and
passengers. Shielding material must be strong enough to deflect the oil at the full
pressure. A mechanical oil pressure gauge must use braided lines.
est
.1
987
MTRA
I
nt
ernat
i
onal
31.B No Blowers (superchargers), Nitrous Oxide, Nitro Methane or any Oxygen Carriers
or Combustion Accelerators allowed.
32.B Vehicles must have operable forward and reverse gears and must be equipped with
reverse gear lockout.
33.B All vehicles must be equipped with a starter interrupter switch that will allow starter
engagement only in the neutral position on a standard transmission or park and
neutral positions on an automatic transmission. Engines cannot start in reverse or
forward gears.
32
R-T ROLLCAGE
34.B All Fiberglass Cab Ride Trucks must have a minimum 2” [51mm] diameter .120
[3.0mm] wall D.O.M., (6) six point one piece rollcage with a rear (X) brace behind the
driver. The (passenger area) must have a rollcage mounted to the frame or frame
outriggers sufficient to protect the passengers. This includes a rollbar, with an “X”
brace, on each end of the passenger seating area.(Refer to figure’s #2b to #4b)
est
.1
987
MTRA
33
I
nt
ernat
i
onal
est
.1
987
MTRA
I
nt
ernat
i
onal
35.B Roll bar Padding is required on all the rollcage within 18” [457mm] of driver and
passengers head areas above his shoulders. It is recommended padding be fireproof
material. The new SFI 45.1 fire retardant padding, ¾” [19mm] minimum is preferred.
34
R-T ENGINE & TRANSMISSIONS
36.B All exhaust pipes and mufflers must be securely attached. It is suggested the
exhaust discharge forward of the passenger area.
37.B All carburetors and fuel injection butterfly shafts must have dual return to idle
springs. A return to idle spring must be located on both butterfly shafts or at both
ends of a single shaft. They cannot be attached at the same location. The spring on
the throttle pedal does not count as one spring but is also recommended, unless it is
a stock, steel cab, factory configuration.
38.B All throttle linkage from cab to the engine must be cable operated and must be a
positive action push pull type unless it is a stock OEM, steel cab, factory
configuration. Throttle toe straps are required and they must be open on the brake
side unless it is a stock, steel cab, factory configuration.
39.B No Mechanical clutch vehicles unless it is a stock OEM, steel cab, factory
configuration.
est
.1
987
MTRA
35
I
nt
ernat
i
onal
R-T DRIVELINE
40.B All chain-drives must be shrouded in all directions with a minimum of (.250) 1/4”
[6mm] aluminum or steel. This shroud must restrain all internal moving parts.
41.B All pieced wheels must have the split ring to the inside when mounted on truck or
must have four bolts 90 degrees apart and corresponding tabs on the wheels for
attaching the ring to the wheel.
est
.1
987
MTRA
36
I
nt
ernat
i
onal
R-T BRAKES
42.B All vehicles must be equipped with foot operated hydraulic brakes in good working
order. The brakes must be able to stop the vehicle in its own length at 10 MPH
[16KPH]. If your vehicle does not have lockers, wheel brakes are recommended.
43.B All rubber tired vehicles must be equipped with dual braking systems consisting of
two master cylinders or a dual cylinder master cylinder with one brake pedal and
individual lines running to the front and rear brakes.
44.B Driveline brake rotors must be steel billet only. A minimum of three tabs, 120
degrees apart, are required to keep the rotor from moving. Tabs are not required if
rotor is mounted on the driveshaft side of the pinion. (Steel billet rotors are solid with
no webbing or fins in center.)
45.B Vehicles equipped with driveline brakes are required to have the front brake
assembly mounted on the front differential. The rear can be mounted on the transfer
case.
46.B A manually operated parking brake is highly recommended.
est
.1
987
MTRA
37
I
nt
ernat
i
onal
R-T RULE VIOLATIONS
47.B If an owner, driver or member breaks a rule, he or she will be subject to a fine or
suspension.
48.B If an owner, driver or member repeatedly breaks a rule or rules, (3 or more times)
he or she will be subject to a fine, suspension and or the loss of his or her MTRA
Membership and License.
49.B The inspection sheets are legal rule violation reports and members will be fined
accordingly.
50.B MTRA fines and suspensions will be issued by the Board of Directors after a
hearing with a 75% Director majority required for ratification. Hearings can be carried
out by mail or fax.
51.B Minor rules affect the safety of the driver only. A minimum fine of $25.00 [£15.00] for
the first time violator and $50.00 [£30.00] for the repeat offender.
MTRA
52.B Major rulese
affect
the safety of spectators and participants. A major rule violation is
st
.1
987
I
nt
ernat
i
onal
subject to a maximum fine of $5000.00, [£2,800.00] up to one year suspension and
or termination of MTRA Membership and License. The amount or the fine and or
suspension would depend on the severity of the violation and would be determined by
a majority vote of the current MTRA directors.
53.B Non-safety rules do not affect the safety of the driver, spectator or participant. A fine
of $25.00 [£15.00] for first time violators and $75.00 [£45.00] for the repeat offender.
54.B All fines must be paid within 45 days or MTRA Membership and License will be
revoked. Written protest will be accepted only after the fines are paid. Membership
and License cannot be renewed unless all fines are paid.
55.B Promoter Members will be notified of all Major rule violations.
38
Section C
RECOMMENDED MTRA PROTEST
PROCEDURE:
Cubic inch tear down
Fuel test
Blower size
Weight
$250.00 [£140.00]
$100.00 [£56.00]
$150.00 [£85.00]
$50.00 [£30.00]
MTRA will treat all protest infractions as a major rule violation and penalties
will be issued accordingly.
est
.1
987
MTRA
39
I
nt
ernat
i
onal
MTRA DIRECTORS & OFFICERS
President
Vice President
Promoter Director
Technical Director
Membership Director
Sponsorship Director
Communication Director
Secretary/Treasurer
Administrator
MTRA
esMTRAE
t
.1
987EU, OFFICERS AND DIRECTORS
I
nt
ernat
i
onal
President
Officer
Officer
40
Useful Information
Weights:
Oil 1 gallon = 7.0 Lbs. 1 qt. = 1.75 [3.78 litres]
Gas 1 gallon = 6.2 Lbs. 1 qt. = 1.55 [3.78 litres]
Water 1 gallon = 8.4 Lbs. 1 qt. = 2.10 [3.78 litres]
Tubing Weights:
2” x .120 wall D.O.M. tubing = 2.409 Lbs. per foot.
[50mm x 3.1mm CDS =3.49KG per Metre]
1-1/4” .095 wall D.O.M. tubing = 1.172 Lbs. per foot.
[31.75mm x 24.13 CDS =1.69KG per Metre]
Metric and Standard Conversion
Length:
1 Kilometer = 1000 meters = 3280.83 ft. = .625 miles
1 Meter = 100 centimeters = 39.37 in. = 1.09 yds.
1 Centimeter = .3937 inch
1 Mile = 1.609 kilometers = 5280 ft.
1 Inch = 2.54 centimeters = 25.4 millimeters
1 Yard = .91 meters
est
.1
987
MTRA
I
nt
ernat
i
onal
Mass:
1 Cubic inch = 16.387 cubic centimeters
1Cubic centimeter = .061024 cubic inches
1 Kilogram = 1,000 grams = 2.2045855 Lbs.
1 LB = 453.6 grams ~ 1 Ounce = 28.35 grams
Kilograms divided by 2.20 = Lbs. ~ Lbs. x 2.20 = kilos
Volume:
1 Liter = 100 cubic centimeters or 61.025 cubic inches
Formulas:
Circumference = pi x diameter = πD
Area of circle = pi x (radius x radius) = πr²
Volume of cylinder = area x height
r² = radius squared = radius x radius
π = “pi” = 3.141592 = squared
ci = cubic inch cc = cubic centimeter
Volumes:
bore² x 12.87 deck clearance = cc of deck clearance.
bore² x .7854 x deck clearance = ci of deck clearance.
bore² x 12.87 x thickness of gasket = cc of head gasket.
bore² x .7854 x thickness of gasket = ci of head gasket.
Displacement:
bore x bore x stroke x .7854 x # of cyl. = Displacement
41
Vehicle/Driver Specifications Reference List
Flywheel SFI_____ Mfg.______________________
Serial #______________
Exp. Date______________
Bellhousing SFI 6.3 Mfg.______________________ Serial #_______________ Exp.
Date______(2yr max)
Flex plate SFI 29.1 Mfg._______________________ Serial #_______________ Exp.
est
.1
987
MTRA
I
nt
ernat
i
onal
Date____________
Trans Blanket SFI 4.1 Mfg._____________________ Serial#________________Exp.
Date____________
Harness SFI 16.1
Mfg._ ______________(2yr max) Serial# _______________
Exp. Date____________
Firesuit SFI 3-2A/15 Mfg._____________________
Gloves/Shoes SFI 3.3 Mfg.____________________
Neck Collar SFI 3.3 Mfg.______________________
42
Helmet SFI 31.1 or 31.2 or SA2000 Date__________
Fire Extinguisher
Type______ Date_____________
Fire System Lbs._____ Date tested_____________
CDL
Date__________(2yr max)
RII Radio Mfr.______________________________
Certification Date________________________
est
.1
987
MTRA
I
nt
ernat
i
onal
Vehicle Weight______________________
Rollcage Size/Thickness_____________________
Rollcage Padding
SFI 45.1 Size______________
Supercharger Size________________________
% Overdrive___________ Rotor length_________
Engine Make___________ Cubic Inch__________
43
Rule Revisions
Page #_____
Page #_____
est
.1
987
Page #_____
MTRA
Rule change or update suggestions
44
I
nt
ernat
i
onal
Use this section to inspect your vehicle before contacting a MTRA® certified
inspector.
SECTION “A” EXTERNAL CHECK
Helmet Snell SA2000/SFI 31.1 or 2 & Firesuit
RII Trans & Rec, Eng will not start with RII off
RII lights 12” from center, Number 2”x 2”
Rear kill switch, pull type, must kill battery power
Rear back-up alarm & light
Battery secure & covered, Dry or Gel type only
External Crossover Relief Valve on front steering
9,000 lbs min weight
Shock accumulators securely mounted
Fuel tanks anti-spill securely mounted
Firewall & windshield required
Seat mounted to frame or frame outriggers
Wheel restraint system
est
.1
987
MT
RA
Engine
I
nt
ernat
i
onal
Exhaust must discharge vertical or 45 deg down
Carb or Inject butterfly shafts dual return springs
Throttle linkage must be push/pull type cable
Deflection shield on both sides of engine
Blower; max 10% overdrive, 871, 16” rotors, etc
Elect fans only, no cast iron or cast steel pulleys
Approved harmonic balancer/shield
575 Cubic inch engine maximum
No combustion accelerators
Transmission & Clutch
SFI 4.1 Trans blanket not torn or burnt
Approved SFI flex plate
Lenco blanket & 360 deg enclosure
Approved explosion proof bellhousing, not welded, approved hole cover
Clutch; approved steel plate or billet flywheel
Clutch; full block-saver plate
45
BRAKES & DRIVELINE
Driveline loops, max 12” OC, min 2 loops
Driveshaft loops, 360 deg & round
Jack shafts & couplers 360 deg enclosure
Slip yoke min penetration 2” in all config
U-Joint enclosed 360 deg, guard dist. 2”
Chain drives, meet MTRA specifications
Dual brake system, 2 master cyl, one brake pedal
Steel billet rotors 3 tabs
SECTION “B” IN-CAB
RII receiver antenna mounted vertical
Current Vehicle Cert Check sheet displayed
Commercial back-up alarm, mechanically activated
In-cab kill switch shuts off battery, push type
Fire retardant system, 6 nozzles
2½ lb Halon or ABC fire extinguisher with gauge 2 yr
Driver protected from tire debris
3” 5 pt harness,
mount
to frame/outriggers 2 yr
est
.1
987
I
nt
ernat
i
onal
No fuel or fuel lines, batteries, radiators or water hoses in the driver’s compartment
In-cab fuel shutoff
Forward/reverse gear lockout
Starter interrupter – park/neutral start only
Rollcage & frame repairs require 6” internal sleeve 8 point, one piece, 2”OD, .120 wall
DOM tubing, driver “X” brace from frame to top
Padding; ¾” SFI 45.1, by drivers head
2 rollcage sidebars
Throttle toe strap
MTRA
SECTION “C” DRIVER IN-CAB
Can the driver operate the kill switch & fire system with his eyes closed
Test kill switch and RII with engine running
Foot operated Hydraulic brakes
Max stopping distance, vehicle length at 10 mph
46
CHAIN DRIVE TRANSFER CASE SPECIFICATIONS
CHAIN SIZE: Triple 60, Minimum. Though there are double chains that are as strong or stronger,
a triple chain is recommended.
CHAIN TYPE: Chain must be full roller type and riveted construction. No spring clip master links
allowed. Master link must be riveted or cotter pin type. Only one master link is allowed in the
chain. Riveted master link or continuous loop chain is recommended.
SPROCKETS: All drive sprockets must be nineteen (19) tooth (Approximately six inches in
diameter) minimum.
CONSTRUCTION: ¼” steel minimum must be used for the outer frame case. It must cover all
four sides (top to bottom) for 360 degree coverage (The entire circumference). The case must be
wide enough to cover the chain completely as viewed from the side. The case must be securely
attached to the chassis. The case can be welded to the frame or part of the chassis structure
providing the minimum material requirements are met. Chain cannot be more then three (3)
inches from outer frame on the sides and top of the case. The case must have enough room for
the chain to gather in the bottom in the event of a chain failure. Suggested minimum distance from
the bottom of the case to the lowest point of the chain is four (4) inches. Inspection Covers must
est
.1
I
nt
ern
at
i
onal between the
give Inspectors access
to987
see and measure size of the chain, sprockets,
and
distance
chain and case. The case frame and inspection covers must prevent any part of the chain,
sprockets, or shafts from escaping. No part of the chain or internals should be seen from outside
the case once all inspection covers are secured. Any part of the case where adjusters, tensioners,
or shaft bearings are attached must be ¼” steel, minimum. Inspection covers can be ¼” steel or
aluminum, minimum. Any removable part of the case must be secured with a minimum of 4 (One
at each corner) 3/8” Grade 8 bolts. Maximum center to center distance between any bolt along
any edge of an inspection cover (I.E. horizontal and vertical edges) is 10”. See illustration.
MTRA
TENSIONERS AND ADJUSTERS: The chain drive must incorporate tensioners or adjusters.
Both must have locking bolts or nuts to prevent unloosening of the chain.
CHAIN LIFE: Maximum allowable chain life is two (2) years. The entire chain and its master link
must be replaced after two years of service.
SHAFT SIZE: Minimum shaft size is 1-1/4” inches.
Approval of the chain drive transfer case will be granted based on complete following of these
specifications. No exceptions allowed.
47
est
.1
987
MTRA
I
nt
ernat
i
onal
Copyright 2010 MTRA® MTRAE®
48
est
.1
987
MTRA
49
I
nt
ernat
i
onal
est
.1
987
MTRA
50
67 66 65 64 63 63 62 61 60 59 58 57 56 55 54 53 53 52 51 50 49 48 47
66 65 64 63 62 62 61 60 59 58 57 56 55 54 53 52 52 51 50 49 48 47 46
65 64 63 62 61 61 60 59 58 57 56 55 54 53 52 51 51 50 49 48 47 46 45
64 63 62 61 60 60 59 58 57 56 55 54 53 52 51 50 50 49 48 47 46 45 44
70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48
46 45 44 43
45 44 43 42 42 41 40 39 38 37 36 35 34 33 32
44 43 42 41 41 40 39 38 37 36 35 34 33 32 31 31 30 29 28 27 26
43 42 41 40 40 39 38 37 36 35 34 33 32 31 30 30 29 28 27 26 25 25
47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
I
nt
ernat
i
onal
Copyright 2010 MTRA® MTRAE®
69 68 67 66 65
68 67 66 65 64 64 63 62 61 60 59 58 57 56 55 54
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
LOWER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
UPPER
PULLEY
LOWER
PULLEY
M T R A®
BLOWER
OVERDRIVE COMBINATIONS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising