Installation Guide - TP-Link

Installation Guide - TP-Link
Installation Guide
PoE Injector (TL-POE150S)
PoE Splitter (TL-POE10R)
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code.
7106507214 REV1.0.2
Some models featured in this guide may be unavailable in your country or region. For local sales information, visit http://www.tp-link.com.
PoE Injector Only
The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP and PoE IP
Phone through an Ethernet cable.
PoE Injector
PoE Inj
ec
tor
Powered Device (PD)
Ethernet Device
Power Socket
(switch, router, etc.)
LAN IN
PoE Splitter Only
PWR DC 48V
IP Camera
AP
IP Phone
The PoE Splitter can be used with a PoE/PoE+ switch to deliver direct current (DC) power and data to a Non-PoE device.
12V 9V 5V
PoE Splitter
PoE Sp
litt
er
Set the required voltage
of the non-PoE device
before cable connection.
PoE/PoE+ Switch
LAN OUT
PWR DC OUT
Non-PoE Device
(suggested power:<10W)
PoE Injector & Splitter
The PoE injector and PoE splitter can be used as a kit to supply power and transmit data to a Non-PoE device.
Ethernet Device
PoE Injector
12V 9V 5V
PoE Splitter
Set the required voltage
of the non-PoE device
before cable connection.
PoE Inj
PoE Sp
litt
er
ector
(switch, router, etc.)
Power Socket
LAN IN
PWR DC 48V
LAN OUT
PWR DC OUT
Non-PoE Device
(suggested power:<10W)
Power LED Explanation
PoE Injector:
LAN IN
PoE Splitter:
LAN OUT
PWR DC 48V
Steady blend of red & yellow: No power supply
Steady green: Supplying power normally
Flashing: Supplying power abnormally
PWR DC OUT
Flashing: The DC OUT port has no link
Steady green: Supplying power normally
OFF: No PSE is connected/Power-overload
FAQ
General Specifications
Standards
IEEE 802.3, IEEE802.3u, IEEE 802.3ab, IEEE 802.3af
Q1. Can the PoE Injector supply power to a PoE device which doesn’t
have a gigabit PoE port?
LED
PWR
Cable Type
UTP/STP of Cat. 5 or above (based on the standards that the
connected devices comply with)
Ports
PoE Injector:
10/100/1000Mbps Auto-Negotiation RJ45 LAN IN port
10/100/1000Mbps Auto-Negotiation RJ45 POWER+DATA
OUT port
DC 48V Power Input port
A: Yes, both LAN and PoE ports comply with IEEE 802.3, IEEE 802.3u and IEEE
802.3ab standards and support 10/100/1000Mbps Auto-Negotiation.
Q2. What can I do if my PoE Injector does not supply power to the
powered device or the supplied power is unstable?
A1: Ensure the PD is PoE-compliant and its connecting port supports the
PoE function.
A2: Ensure the power consumption of the PD doesn’t exceed 15.4W,
otherwise the overload protection of the PoE Injector will be activated. The
PoE Injector complies with IEEE 802.3af standard and supports 15.4W to a
PD, while the quality and length of the Ethernet cable may influence the
reception of the power supply.
Q3. Must I use the PoE Injector together with the PoE Splitter?
A: No. The PoE Injector can supply power to all PDs compliant with IEEE
802.3af standard. The PoE Splitter is used with a PoE switch or the PoE
Injector to supply power to a non-PoE device.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
SAFETY NOTICES
Cautions
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from
lightning.
PoE Splitter:
10/100/1000Mbps Auto-Negotiation RJ45 POWER+DATA IN
port
10/100/1000Mbps Auto-Negotiation RJ45 LAN OUT port
5V/9V/12V DC OUT Power Output port
Environmental and Physical Specifications
Operationg Temperature
0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature
-40˚C to 70˚C (-40˚F to 158˚F)
Operationg Humidity
10% to 90% non-condensing
Storage Humidity
5% to 90% non-condensing
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних
документів та вимогам, що передбачені чинними законодавчими актами України.
Use only power supplies which are provided by manufacturer and in the original packing of this
product. If you have any questions, please don't hesitate to contact us.
Explanation of the symbols on the product label
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This
means that this product must be handled pursuant to European directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he
buys a new electrical or electronic equipment.
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
© 2017 TP-LINK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising