page e8-e9 - hot surface ignitors (hsi)

page e8-e9 - hot surface ignitors (hsi)
#4 HEATING COMPONENETS_2011CatalogTemplates 11/27/2010 4:12 PM Page 9
Use these igniters with the “J” style pilot burners.
Igniters are suitable for panel mounting. The
LH33CM600 may be mounted directly on Penn
valves EF33CZ206 and 209. The LH33CZ003
can be mounted on Penn valve EF33CZ210 by
removing mounting bracket.
The LH33CM018 sensor and RM01680001
sensor cable are required. 24 volt system.
PART NO
LH33CZ003
HOT SURFACE IGNITER
The SX611 Ignition Module generates a
high-voltage spark and provides a continuous
trial for pilot ignition. The SX611 will also automatically try to re-establish the pilot flame should
it be extinguished while the thermostat is calling
for heat.
MODEL NUMBER
SX611
E-8
PART NO
MODEL NUMBER
LH33ZS004
271
Designed specifically for use with LH68005
and LH33JZ053 pilot burners. Locating tabs
and locking screw provide accurate location
for required spark gap. Spike connection
replaces quick connect style.
PART NO
MODEL NUMBER
LH680512
AM11
Provided with mounting clip.
60” leads with 5/64” thick insulation.
PART NO
MODEL NUMBER
LH33EW058
760-679
FLAME SENSOR
Sensor is designed for use with
LH33ZS004 Hot Surface Igniter.
PART NO
80° FURNACE USE LH680012
90° FURNACE USE LH680013
MODEL NUMBER
CE6
CE6
Motors
Electrical
Universal Hot Surface Ignition Module
• Provides easy field-replacement of a
wide range of hot surface ignition
modules by Honeywell, Robertshaw
and White Rodgers.
• Single rod or remote dual rod
rectification type flame sensing.
PART NO
• LED signals system lockout, weak
P691-S910U
flame signal or internal error.
• Selectable number of ignition trials (1 or 3).
• Selectable length of trial for ignition (4 or 7 seconds).
Designed for use with LH680-012or 013
flame sensor
MODEL NUMBER
G67
Use these igniters with the “J” style pilot
burners. Igniters are suitable for panel
mounting. The LH33CM600 may be
mounted directly on Penn valves
EF33CZ206 and 209. The LH33CZ003 can
be mounted on Penn valve EF33CZ210 by
removing mounting bracket.
PART NO
The LH33CM018 sensor and RM01680001
P691-S8610U
sensor cable are required. 24 volt system.
Universal Intermittent Pilot Module
• Provides ignition sequence, flame rectification and safety shutoff for
intermittent pilot central furnaces and heating appliances.
• For use with single rod or dual rod/remote sense applications.
• For use with natural or LP gas.
• Replaces over 300 existing IP modules including Honeywell,
Robertshaw, Penn Johnson, Fenwal and others.
PART NO
LH33EP040
MODEL NUMBER
G770
Heating
Components
MODEL NUMBER
G60
PART NO
LH33CZ007
Indoor Air
Quality
PART NO
LH33CM600
Use with “J” style pilot.
Panel mount.
24 volt.
100% lockout, 120 sec. nominal trial for
ignition, w/4 sec. pilot gas prepurge.
Thermostats
Use these igniters with the “J” style pilot burners.
Igniters are suitable for panel mounting. The
LH33CM600 may be mounted directly on Penn
valves EF33CZ206 and 209.The LH33CZ003
can be mounted on Penn valve EF33CZ210
by removing mounting bracket.
The LH33CM018 sensor and RM0 1680001
sensor cable are required.24 volt system.
•
•
•
•
MODEL NUMBER
870
Oils &
Chemicals
COMPATIBLE H-W VALVE
8,448,440
ALL I.I.D. VALVES
ALL I.I.D. VALVES
PART NO
LH33JZ050
Accessories, Supplies
& Commodities
PART NO
LH660010
LH660011
LH680510
MODEL
NUMBER
S86E
S86H
S86F
Solid state igniter for use with glow coils used
on 732 and 740 pilot burner. Igniter cycles glow
coil and regulates coil voltage to increase coil
life. System volts – 24
Tools &
Instruments
This igniter provides intermittent pilot burner
ignition. S86E provides continuous trial for
ignition. S86G and S86H provides safe lockout if
pilot does not ignite in 90 second trial for ignition
period. System volts - 25.
Refrigeration
IGNITERS continued from previous page
Compressors,
Chillers, Condensers
Heating Components
#4 HEATING COMPONENETS_2011CatalogTemplates 11/27/2010 4:12 PM Page 10
Electrical
Heating
Components
Indoor Air
Quality
RESISTANCE WIRE
GLOW COILS
This is the replacement ignition coil for the
2H pilot burner supplied in the LH68006 pile
package. Use with 48DA660025 resistance
wire package.
PART NO
LH39JZ051
PILOT STYLE
2H
This package contains stainless
resistance wire used in reducing the
24 volt power source to nominal 9-11 volts
required on some glow coil igniters.
Instruction sheet included.
NOM VOLTS
10
PART NO
48DA660025
This igniter coil assembly is used with pilot
burners LH68005 and LH33JZ053 glow coil
voltage source must be limited to maximum
of 11 volts.
Motors
Compressors,
Chillers, Condensers
Heating Components
PART NO
LH39JZ020
PILOT STYLE
740
High Voltage Ignition Lead Silicone insulated
wire for ignition systems where high
temperature, moisture resistant ignition lead
is required on outdoor equipment.
NOM VOLTS
10
WIRE
PART NO
END CONNECTIONS LENGTH (in)
48MA403742 SPK. PLUG/RING TERM.
20
B0805050
SPARK PLUG
24
48DD410452
Q.C./PIN TERM.
24
301286-702
NONE
27
RM680002
QUICK CONNECT
24
Replaces almost any 30 mV thermocouple.
Average operating life of ten years.
Bottom lock design allows for one hand installation.
Universal adapter makes this the two-to-one installer-preferred
thermocouple in independent HVAC survey.
PART NO
HONEYWELL PART NO
DESCRIPTION
P671-Q340A-18
A340A1066
Thermocouple 18.
P671-Q340A-24
Q340A1074
Thermocouple 24.
P671-Q340A-30
Q340A1082
Thermocouple 30.
P671-Q340A-36
Q340A1090
Thermocouple 36.
P671-Q340A-48
Q340A1108
Thermocouple 48.
LOW PRESSURE SWITCH
These low pressure switches are used
in ignition circuits to interrupt power
when gas pressure is low or gas service
to unit is shut down. Switch has 1/8” NPT
connection on underside.
PART NO
HK02LB005
HK02LB018
Thermostats
PILOT SAFETY SWITCHES
• Solid state lockout timer
• 30 second trial for ignition
• May be reset after 30 sec.
• 24 volt input
Refrigeration
Tools &
Instruments
Accessories, Supplies
& Commodities
Oils &
Chemicals
PART NO
HH72CH003
OHMS PER FT
0.38
IGNITION LEADS
UNIVERSAL THERMOCOUPLE
•
•
•
•
LENGTH (in)
156
RATING
1 AMP
1 AMP
PRESS
SETTING
2 WC "
6 WC "
COMBUSTION BLOWER ASSEMBLY
• 100 CFM Max.
• 230 Volt
• 1/10 H.P.
• PSC motor
• 3450 RPM
MODEL NUMBER
990l141
PART NO
48DA660
Manual reset pilot control which shuts off
gas to pilot and main burners when pilot
flame fails. Includes pilot gas filter. Use with
nominal 30 mV thermocouple.
PART NO
MODEL NUMBER
TUBE SIZE
EF53FB020
C591A
1/4 O.D. "
• 60 CFM Max.
• 230 Volt
• 1/80 H.P
• Shaded pole motor
• 3200 RPM
PART NO
LA25UZ0
RESISTORS
Resistors and resistance wire are required
on some units to reduce the voltage to ignition glow coils. Refer to unit installation and
service instructions.
PART NO
HT21AU004
HT21AU020
55939D5
OHMS
RESISTANCE
4
5
3
OIL BURNER COMPONENTS
OIL PUMPS
• Compact size
• 5/16” dia. shaft
• Integral bleed fitting for easy start up
PART NO
58HH680027
58HH680029
58HH680001
58HH680002
WATTS
20
20
8
E-9
PUMP STAGES
1
2
1
2
PUMP RPM
1725
1725
3450
3450
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising