CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W

Before using the light, please thoroughly read this manual and keep it for future reference.

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these periodically.

• If a child swallows a battery, consult a doctor immediately.

• Avoid having the computer in direct sunlight for unnecessary or extended periods.

• Do not disassemble the computer.

• Do not drop the computer. Doing so may result in a computer malfunction or damage.

• When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sunglass lenses.

Wireless Sensor

The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of interference.

When adjusting the wireless sensor, note the following:

• Signals cannot be received if the distance between the sensor and the computer is too great.

• The transmission distance may be shorter due to low temperature or low battery.

• Signals can be received only when the back of the computer is facing the sensor.

Interference may occur, resulting in incorrect data, if the computer is:

• Near a TV, PC, radio, motor, or in a car or train.

• Close to a railroad crossing, railway tracks, TV stations and/or radar base.

• Using with other wireless devices in close proximity.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)This device may not cause harmful interference,and (2)this device must accept any interference received,including interference that may cause undesired operation.

Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user

’s authority to operate the equipment.

1

2

3

4

Preparing the computer

Clear all data (initialization)

Press the AC button on the back.

Select the desired speed units

Select “

: Speed unit

: Wheel size icon

: Sensor signal reception icon

” or “ km/h ↔ mph

”.

Register the setting

Enter the tire circumference

When the computer is mounted on the bracket

AC

Enter the tire circumference of your bicycle in mm.

* Refer to the tire circumference reference table.

Increase

Set the clock

Battery case cover

MENU

AC

MODE

Move digits

(by pressing

& holding)

Register the setting

When MODE is pressed and held, “Displayed time”, “Hour”, and “Minute” will appear, in this order.

24h ↔ 12h, or increase the value

Switch the screen or move digits

(by pressing

& holding)

Register the setting

(finish)

Push!

Tire circumference reference table

L (mm)

1952

1953

1970

2068

2100

2005

2010

2023

2050

2055

2068

2070

2083

2170

2145

2155

2161

2169

1938

1515

1615

1770

1785

1753

1785

1795

1905

935

1020

1055

1185

1195

1340

1350

1890

1925

1965

1920

1913

1944

2090

2125

2105

2070

2080

2086

2096

2105

2136

2146

2155

2130

2168

2180

2200

2288

2326

Tire size

24 x 1.75

24 x 2.00

24 x 2.125

26 x 7/8

26 x 1(59)

26 x 1(65)

26 x 1.25

26 x 1-1/8

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.10

26 x 2.125

12 x 1.75

14 x 1.50

14 x 1.75

16 x 1.50

16 x 1.75

18 x 1.50

18 x 1.75

20 x 1.75

20 x 1-3/8

22 x 1-3/8

22 x 1-1/2

24 x 1

24 x 3/4 Tubular

24 x 1-1/8

24 x 1-1/4

26 x 2.35

26 x 3.00

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 20C

650 x 23C

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 40C

29 x 2.1

29 x 2.3

Measure wheel circumference (L) of your bike

To get the most accurate calibration do a wheel roll out.

W i t h t h e v a l v e s t e m perpendicular to the ground, mark the pavement at the valve stem. With the riders weight on the bike, roll the wheel one tire revolution in a straight line and mark the ground when the valve stem is perpendicular to the ground again. Measure the distance in millimeters. This is the most accurate wheel calibration number.

L mm

Install the sensor and magnet

A

The distance between the computer and the sensor must not exceed the transmission range of 70 cm. The back of the computer must face the sensor.

YES!

NO!

B

The magnet must pass through the sensor zone.

Max

70 cm

SENSO

ZONE

Sensor zone

Inside of right front fork

C

The clearance between the sensor surface and the magnet must not exceed 5 mm.

4

5 mm

3

4

SENSOR

ZONE

3

1

Install the sensor

5

3

SENSOR

ZONE

* Install the sensor as close to the upper part of the front fork as possible.

3

Attach the bracket to the stem or handlebar

When attaching the bracket to the stem

6

Stem

2

1

4

Remove/install the computer

Holding the unit

Click

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending

Copyright© 2007 CATEYE Co., Ltd.

CCRD3W-070115 066600540 3

How to install the unit on your bicycle

1

2

6

3

5

4

7

1 Bracket band

2 Bracket

3 Speed sensor

4 Magnet

5 Sensor rubber pad

6 Bracket rubber pad

7 Nylon ties (x2)

Inside of right front fork

Pull securely

7

SENSOR

ZONE

ENG

2

Install the magnet

Spoke

4

Toward the sensor zone

Caution:

Make sure that the back of the computer faces the sensor.

* The computer may not function appropriately on some stem if its back does not face the sensor as shown in A .

When attaching the bracket to the handlebar

6

Handlebar

1

2

Push outward

Cut

Caution:

Round off the cut edge of the bracket band to prevent injury.

* After installation, rotate the front wheel gently to check that the speed is displayed on the computer. If the speed is not displayed, check that conditions A , B , and C , above, have been done appropriately.

CC-RD300W

Operating the computer [Measuring screen]

MODE

*1

Tm

Elapsed Time

0:00’00” - 9:59’59”

Dst

Trip Distance

0.00 - 999.99 km [mile]

Dst

2

Trip Distance-2

0.00 - 999.99 /

1000.0 - 9999.9 km [mile]

Av

Average Speed

0.0 - 105.9 km/h

[0.0 - 65.9 mph]

0.0(4.0) - 105.9 km/h

[0.0(3.0) - 65.9 mph]

Odo

0.0 - 9999.9 /

*2

Mx

Maximum Speed

Total Distance

10000 - 99999 km [mile]

Clock

0:00 - 23:59 or 1:00 - 12:59

*1 With the computer installed on the bracket, press on the three raised dots on the face of the computer.

*2 If Tm exceeds approximately 27 hours or DST exceeds 999.99 km, .E (Error) is displayed as the average speed. Reset data.

Pace arrow

Indicates whether the current speed is faster ( ) or slower ( ) than the average speed.

Current speed

0.0(4.0) - 105.9 km

[0.0(3.0) - 65.9 mph]

Selected Mode

Starting/Stopping measurement

Measurements occur automatically when the bicycle is in use. During measurement, or flashes.

Switching computer function

Pressing MODE switches function, in order, as shown on the left.

Resetting data

To reset measurement data, display any data other than for Dst-2 and then press and hold MODE. Pressing and holding MODE with Dst-2 displayed resets Dst-2 only.

The total distance is never reset.

Power-saving function

If the computer has not received a signal for 10 minutes, power-saving mode will activate and only the clock will be displayed. When the computer receives a sensor signal again, the measuring screen reappears. If two weeks’ inactivity elapses, power-saving mode will change to SLEEP mode. Pressing the MODE in SLEEP mode brings up the measuring screen.

Changing the computer settings [menu screen]

If the MENU is pressed with the measuring screen displayed, the menu screen appears. Press the MODE when measurement has stopped and no signal is being received to change menu settings.

Wheel selection

Wheel size entry

Clock setting Total distance manual entry

Speed unit

Setting change (by pressing & holding)

* After changing, be sure to press MENU to register the setting.

* If the menu screen is not touched for a minute, the

Measuring screen reappears without data changes.

Wheel selection ..... Toggle between the specified wheel size (tire circumference)

and . Use this function if the computer is to be shared between two bicycles.

................................ Pressing MODE toggles between and .

Wheel size entry .... Pressing MODE increases the value, and pressing and holding MODE moves to the next digit.

* To enter the wheel size , display using “Wheel selection”.

Clock setting .......... To set the clock, refer to “Preparing the computer-4”.

Total distance manual entry

................................ Before reinitializing the computer, note the total distance. This reading will later allow you to enter the total distance manually. Pressing MODE increases the value, and pressing and holding MODE moves to the next digit.

Speed unit .............. Pressing MODE toggles between and .

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

Replacing the battery

TO

P

Computer

If the display appears faded, replace the battery.

Install a new lithium battery (CR2032) with the (+) side facing upward. Then reinitialize the computer referring to “Preparing the computer”.

* When the battery is installed, place the seal with the “TOP” side upward.

Push!

TOP

Sensor

If sensor reception is poor, replace the battery.

After replacement, check the positions of the sensor and magnet.

CR2032

Seal

CR2032

COIN

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.

Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.

The sensor signal reception icon does not flash. (The speed is not displayed.)

(Spin the front wheel, bringing the computer closer to the sensor. If the icon now flashes, this indicates that the computer and sensor are too far apart or that the battery is low.)

Is the clearance between the sensor and magnet too great? (must be ≤ 5 mm)

Does the magnet pass through the sensor zone?

Adjust the positions of the magnet and sensor.

Is the computer installed at the correct angle?

Back of computer must face toward the sensor.

Are the computer and sensor too far apart? (The distance must not exceed 70 cm.)

Install the sensor closer to the computer.

Is the computer or sensor battery weak?

In winter, battery performance diminishes.

Replace the battery. In the case of the computer, after replacing the battery, re-start the computer according to the

“Preparing the computer”, above.

No display.

Is battery in the computer run down?

Replace it. Then reinitialize the computer referring to “Preparing the computer”.

Incorrect data appear.

Reinitialize the computer referring to “Preparing the computer”.

Specification

Battery ................. Computer : Lithium battery (CR2032) x 1

Sensor : Lithium battery (CR2032) x 1

Battery life ........... Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary

Sensor depending on the conditions of use.)

: Unit Total Distance reaches about 10,000 km (6,250 mile)

* This is the average figure of being used under 20 °C temperature and the distance between the computer and the sensor is 65 cm.

Controller .................................. 4-bite, 1-chip microcomputer (Crystal controlled oscillator)

Display ...................................... Liquid crystal display

Sensor ...................................... No contact magnetic sensor

Wheel circumference range ..... 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)

Working temperature ............... 32 °F - 104 °F (0 °C - 40 °C) (This product will not function appropriately when exceeding the

Working Temperature range. Slow response or black LCD at lower or higher temperature may happen respectively.)

Dimensions/weight ................... 1-53/64” x 1-7/32” x 5/8” (46.5 x 31 x 16 mm) / 0.78 oz (22 g)

* The factory-loaded battery life might be shorter than the above-mentioned specification.

* The specifications and design are subject to change without notice.

Standard Parts

#160-2190

Parts kit

#160-2196

Speed sensor

#169-9691

Wheel magnet

#160-0280

Bracket band

#166-5150

Lithium battery

(CR2032)

#160-2193

Bracket

LIMITED WARRANTY

2-Year Computer only

(Accessories/Bracket sensor and Battery Consumption excluded)

CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer.

To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certificate.

Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.

For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn: CATEYE Customer Service Section

Service & Research Address for USA

CATEYE Service and Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303.443.4595

Toll Free: 800.5CATEYE

Fax: 303.473.0006

E-mail: [email protected]

URL: http://www.cateye.com