da Vinci Jr. 2.0 Mix User Manual

da Vinci Jr. 2.0 Mix User Manual
da Vinci Jr.2.0 Mix
July 2016
da Vinci Jr. 2.0 Mix 3D Printer
da Vinci Jr. 2.0 Mix
User Manual
P1
da Vinci Jr.2.0 Mix
July 2016
The purpose of this user manual is to help users understand and use the da Vinci Jr. 2.0 Mix 3D printer correctly. It contains
the operating instructions, maintenance information and application skills of the da Vinci Jr. 2.0 Mix 3D printer. To learn
more about the latest news of the da Vinci Jr. 2.0 Mix 3D printer, please contact local dealers or visit the official website of
XYZprinting: http://www.xyzprinting.com
Trademarks
All trademarks and registered trademarks are the property of their respective owners.
Print History
New editions of this manual incorporate new and changed material different from previous editions. Minor corrections and
updates may be incorporated into reprints of the current edition without releasing additional announcements or documentation regarding the updated version. The User Manual is for user reference only. If you need to obtain the latest information,
you are welcomed to visit the XYZprinting website: www.xyzprinting.com
1 Before using this printer, please first remove
the fixed materials from the printing module and
printing bed. Switching on the printer's power
without removing these fixed materials may
damage the machine.
2 Before launching XYZware, connect the PC to with printer
using the USB cable. For a better user
experience, it is strongly advised to follow the proper
procedure for using the product.
3
3 Registration via XYZware before your first print
is strongly recommended. When registered with
XYZprinting, you will receive latest technical
supports and updates. To register, simply click
"Register Now" to begin.
4 Before you start printing, please affix the bed tape on the print
bed. The bed tape may be removed after printing is complete. (Bed
tape can be reused.)
5 You may use XYZware to initiate manual updates to the printer
firmware and software. When using the printer for the first time,
we recommend connecting to the Internet and performing manual
update once to obtain the latest resources.
6 The optimal room temperature for printing is 15-26 ◦C (60-78 ◦F).
Printing quality may be affected if room temperature is higher or
lower.
7 If you need more detailed technical support and program
resources, visit the website:
http://support.xyzprinting.com/global_en/Support
5
8
8 Before operating the printer, insert the SD card in the SD card port
to make sure that the printing program is able to run properly.
Please carefully read the contents of the product
instruction manual before using this product.
P2
da Vinci Jr.2.0 Mix
July 2016
Product Overview
G
J
K
A: Filament movement area
G: SD card port
(Storage format: FAT32
Systems are compatible with SDHC
cards up to 32GB in size.)
H: Control and display panel
I: Front cover
B: Feed module 1
J:Feed module 2
C: Detector
K:Filament 2
D: Extruder
E: Filament 1
F: Print bed
USB Port
Power Connector
Accessory Checklist
.Guide tube X 2
.Cleaning Brush
Power Switch
.Feeding Path Cleaning Wire x2
.Scraper
.Cleaning Wire x 5
.SD Card
.Power Adapter
.USB Wire
.Power Cord
.Bed Tape X 3pcs
.Bundled filament X 2
.Extruder
.Feeding Tube Grip X2
Important Safety Instruction for Use of Maintenance Tools
• The maintenance tools provided should be only handled by an adult. Please keep the tools away
from children.
• Store the gear cleaning brush properly. This tool shall only be used to clean the specified parts of
the machine and to prevent damage to the machine should not be used to clean other areas.
• The scraper is used to remove the object from the print bed when printing has finished. The bed tape
is reusable and it can be replaced when it has worn out.
Important Safety Instruction
• Do not place the printer in humid or dusty environment such as bathrooms and high traffic areas.
• Do not place the printer on a rickety surface and/or inclined position. Printer may fall down/or
tumble and it may cause serious injury.
• Please keep the front door closed during printing to avoid injury.
• Do not touch the interior of the printer while printing. As it may be hot and include moving parts.
Product Overview
P3
da Vinci Jr.2.0 Mix
July 2016
1 Open the box and remove the
2 Remove the plastic bag and
accessories and cushions.
3 Remove all fixing tape and the
cushion between print bed and
extruder module.
5 Be sure to remove the
paper cardboard on the left side.
8
the tape.
4 Remove the securing styrofoam and fixing tape on the print
bed.
6 Be sure to remove the fixing
cushion on the right side.
Refer to page 5 to install the filament guide tube and
extruder, and then insert the SD card that came with
the printer into your computer or download the latest
XYZware from the official Website and install it on the
computer.
9
7 Be sure to remove the fixing
tape at the back and front of
the print bed.
Use the USB cable to connect the printer to your
PC. Connect the power cord to the printer then
turn on the power switch.
Note: please use the original power adapter and power cord along with the printer in order to
prevent product damage or safety hazards caused by differences in voltage specifications.
Unpacking the Product
P4
da Vinci Jr.2.0 Mix
July 2016
Note: Please follow these steps and ensure that the guide tube and extruder are properly
installed before starating the "LOAD FILAMENT" function. Failure to install the guide tube will
disrupt filament feed.
Install the Filament Guide Tube and Extruder
1 Insert the filament guide tube into the feed module tube
port and finish two sides installation.
3 Connect the filament guide tube to the extruder
Insert the guide tube into feed module 1 and 2.
Make sure it goes all the way down, as shown in the
the illustration.
2 Take the flat cable out from the right side of the
printer and connect it to the extruder.
4 Install the extruder
Align the extruder with the bracket and press the
extruder to attach it to the socket.
Reminder: When installing the filament guide tubes, please attach
them in an intersecting way as shown below. Turn on the power once
the installation process is complete.
Feed
module 1
Feed
module 2
Installing the Accessories
P5
da Vinci Jr.2.0 Mix
July 2016
Chang Spool
1 First retrieve the filament spool to install the filament
spool axle ring.
3 Install the sensor chip. Please pay attention to the position
of the installation holes on the chip.
5 Place the assembled filament spool (with the spool axle
ring) on the filament holder on the left side of the printer.
2 Take out and separate the filament spool
axle ring into its two components.
4 Insert the filament spool axle ring components to
either side of the filament spool, and use a phillips
screwdriver to tighten and secure the rings to the
axle to complete the installation of the filament
spool axle rings.
6 Pull out a section of the filament and insert it into
the feed port.
Caution: Pay attention to the direction the
filament is being pulled out and ensure that
the filament spool axle is rotating smoothly.
Note : Before pushing the filament into the
guide hole, please cut the tip of the filament
off at a 45°
7 Open the release arm and push the filament all the way to the top
so that the front end of the filament is completely inserted into the
feed module. Make sure that the filament is past the motor and that
you can see it in the filament guide tube.
Load Filament
P6
da Vinci Jr.2.0 Mix
July 2016
Auto-loading Filament
1 Select "UTILITIES" > "CHANGE SPOOL" > "LOAD FILAMENT".
Jr. Mix
BUILD (SD CARD)
UTILITIES
SETTINGS
UTILITIES
CHANGE SPOOL
HOME AXES
JOG MODE
2 Wait for the screen to show
CHANGE SPOOL
LOAD FILAMENT
UNLOAD FILAMENT
3 After installing both filaments, press "OK" to continue. Wait
"INSERT FILAMENT", and insert the filament
i n t o t he f ilam en t h o l e . T h e p ri n te r w i l l
automatically feed the filament to the extruder
module via the guide tube.
for the extruder to heat up and load the filament.
Check if the nozzle is extruding filament and press "OK" to
go back to the main menu.
INSERT FILAMENT
DOES FILAMENT
COME OUT NOZZLE
[ OK ] TO FINISH
[ < ] TO RETRY
LOADING
PLEASE WAIT
[ OK ] TO CONTINUE
[ OK ] STOP LOADING
Please ensure both filaments are inserted, the printer cannot start with only one filament. If the printer cannot load the filament
successfully,please reboot the printer and try again.
Manual Loading Filament
1 Please insert the two filaments through the
filament hole, making sure that the filament
passes through the guide tube and meets
with the extruder module. Next, use the
control panel to load the filament.
2 Select " LOAD FILAMENT" on the printer.
CHANGE SPOOL
LOAD FILAMENT
UNLOAD FILAMENT
3 Wait for the extruder to heat up and load filament. Check if the nozzle
extrudes filament and press "OK" to go back to main menu.
DOES FILAMENT
COME OUT NOZZLE
[ OK ] TO FINISH
[ < ] TO RETRY
LOADING
PLEASE WAIT
[ OK ] STOP LOADING
Unload Filament
First unload both filaments using the control panel on the printer…
Jr. Mix
UTILITIES
CHANGE SPOOL
HOME AXES
JOG MODE
BUILD (SD CARD)
UTILITIES
SETTINGS
CHANGE SPOOL
LOAD FILAMENT
UNLOAD FILAMENT
1 Select "UTILITIES" > "CHANGE SPOOL" > "UNLOAD FILAMENT".
LOAD FILAMENT
EXTRUDER HEATING
TEMPERATURE 210 ∘ C
PLEASE WAIT
UNLOADING
PLEASE WAIT
[ OK ] TO RETURN
2 Wait for the extruder to heat up and unload filament. Press "OK" and pull out the filament.
When finishing "UNLOAD FILAMENT"
First open the release arm and then pull out the remaining filament .
Arrange it properly for later use.
Note: Always implement the "UNLOAD FILAMENT" function when replacing
the Spool in order to ensure proper removal of the filament. Cutting
filament too closely to the Extruder Module may result in residual
filament blocking and causing damage to your Extruder Module.
Unload Filament
P7
da Vinci Jr.2.0 Mix
About the da Vinci junior series 3D printer
July 2016
The da Vinci junior series 3D printer (da Vinci Jr.) is a brand new product from XYZprinting that is dedicated to the 3D
printer market. Its intricate and colorful exterior as well as its high resolution printing specifications are set to make it
the new favorite for families and home hobbyists. Whether you're creating an enjoyable learning playground to inspire
your children's creativity or unleashing your innovative ideas and quickly generate prototypes for your products.
Present creativity
To learn more about presenting your
creativity, please visit the Gallery section
of XYZprinting's official website.
Product features
• Environmentally friendly 3D printer that satisfies the WEEE recycling requirements, and utilizes the environmentally friendly PLA
filaments for printing.
• Satisfies electrical appliance safety specifications of the EU and many other countries, making it the best home-based 3D printer
for the entire family.
• Detachable SD card that allows you to store 3D model files that you have created and edited for easy printing.
(Please export .stl files into .3w format via XYZware before printing.)
• A gallery of 3D objects is available for download after free registration.
• Amazing power saving design with a maximum power consumption of 75W, offering low power usage even for extended use.
• Weighs only 12 kg, and can be easily integrated in any household and family settings.
• Smart temperature control designs. Cooling fans within the machine is able to adjust and optimize printing temperature to
improve product quality.
Introduction
P8
da Vinci Jr.2.0 Mix
July 2016
Button instructions
After switching on the printer's power, the user may use the display panel at the front of the printer to understand its
status and usage data. The functional buttons on the right allow the user to perform the relevant operations.
Button
Functions
Up
Direction Up
Down
Direction Down
Left
Back to previous menu / Reduce the adjustment value
Right
Forward to submenu / Increase the adjustment value
OK
OK; confirm selection/settings
HOME
Home Button, return to main menu
Function
Description
UTILITIES
Printer adjustment / Change filament / Sample printing
SETTINGS
The parameters of printer
INFO
The firmware and printer statistical information
MONITOR MODE
Monitor of extruder and print bed working temperature and printing progress
DA VINCI Jr. Mix
BUILD FROM CARD
UTILITIES
SETTINGS
Functions
P9
da Vinci Jr.2.0 Mix
July 2016
Home Menu
Top Menu
Sub Menu
Page
LOAD FILAMENT
P6
P7
CHANGE SPOOL
HOME AXES
P7
P11
JOG MODE
P11
BUILD FROM CARD
P11
CALIBRATE
P12
CLEAN NOZZLE
P13
Z OFFSET
P14
BUZZER
P15
LANGUAGE
P15
ENERGY SAVE
P15
AUTO LEVEL
P15
RESTORE DEFAULT
P15
STATISTICS
P16
SYSTEM VERSION
P16
SPOOL STATS
P16
HELP
P16
P16
UNLOAD FILAMENT
UTILITIES
SETTINGS
INFO
MONITOR MODE
The map above shows the functions your may access with the control panel on the printer.
For detailed descriptions of each function, please refer to their respective pages in this user manual.
Maps of Functions
P 10
da Vinci Jr.2.0 Mix
July 2016
HOME AXES
“HOME AXES” moves the extruder to the lower left corner, The "Y-AXIS" print bed will move to the back.
To home axes:
home axes
are you sure
NO
YES
Select “YES” to proceed.
JOG MODE
“JOG MODE” is used to manually move the extruder and the print bed.
To move the extruder:
jog mode
x-axis
y-axis
z-axis
x-axis ok
exit
- ▲ ■ 001mM ▲ +
010mm
020mm
1.Select “X-AXIS” (to move right
and left) and "Z-AXIS" (to move up and down).
Execute "Home Axes" function first to move
"Z-AXIS". “Y-AXIS” (to move print bed
backwards and forwards).
2.Select desired increment of travel with
buttons, and press (or hold)
direction to move the extruder.
or
and
button for desired
BUILD FROM CARD
1 sample models are built into the printer. You may begin your first 3D prints with the samples.
To print a sample:
build FROM CARD
demo
1.Select a sample to print
2.Put the bed tape on the print bed.
DEMO
start building
no
yes
3.Select "YES" to start printing
4.Remove the printed object when the printing has
finished and the print bed has descended.The bed
tape is reusable and it can be replaced when it's worn.
UTILITIES
P 11
da Vinci Jr.2.0 Mix
July 2016
CALIBRATE
Calibration is enabled for this new extruder module. Please update printer firmware via XYZware before using the
new extruder.
1. Active print bed calibration by selecting “UTILITIES”>”CALIBRATE”>”YES” on the screen.
2. Press the detection head on the right side of the print head according to the instruction of screen message, followed
by pressing OK.
PRESS SWITCH (A)
NEXT TO EXTRUDER
[OK] TO CONTINUE
3. Wait for detecting.
4-1A. If "CALIB COMPLETED" is shown for the
detection result, and "AUTO-LEVELING
IS DISABLED NOW" is shown on the screen, it indicates
good platform levelness. Press "OK" to exit and print.
CALIB COMPLETED
AUTO-LEVELING
IS DISABLED NOW
[OK] TO RETURN
CALIB COMPLETED
AUTO-LEVELING
IS ENABLED NOW
[OK] TO RETURN
4-2A. If the detecting result is shown as “FAIL”, press
"OK" to go to next page, and press "OK" again to exit.
CALIB FAILED
AUTO-LEVELING
[OK] TO CONTINUE
4-1B. If you see "AUTO-LEVELING
IS ENABLED NOW", this indicates that the print bed is slightly
unleveled. The printer will adjust the configuration based on
the detecting result automatically while "AUTO LEVEL" is
enabled. The printing mode helps to improve printing quality
with slower printing speed. You may switch off the function
under "Settings".
PLEASE CONTACT
CUSTOMER SERVICE
FOR LEVEL ISSUE
[OK] TO RETURN
4-2B. And check the detecting result by going to “INFO”>
”LEVELING INFO”. Contact customer service for the issue
and provide the details of leveling information.
A 0317 0320 0313
B 0318 0323 0308
C 0312 0300 0440
[OK] TO RETURN
Note:
1.The dirt on the detection pin and the top of Extruder module will influence detection result. Make sure that
the dirt is cleaned before calibration.
2.If the residues is on the top of the Extruder module, the detection result will be shown as follows. Clean
the dirt before recalibration.
A 0000 0000 0000
B 0000 0000 0000
C 0000 0000 0000
[OK] TO RETURN
3. The printer may enable or disable auto-level based on the result of calibration. You may switch off
the function manually under "Settings".
CALIBRATE
P 12
da Vinci Jr.2.0 Mix
July 2016
Note: The machine can be turned off only when the cooling fan of the print head stops running after
the print is completed. Turning off the power directly may clog the print head.
References:
Please refer to
UTILITIES>CLEAN NOZZLE
to remove the blocks out of the print head.
This section describes how to clean the feed module. After heavy use of printer, if feeding of material becomes difficult or impossible, please follow these steps.
Preparation of Tools
A. Cleaning brush that comes with the printer
B. Screwdriver (T10) for standard cleaning procedure
A. Quick Cleaning
1 Use the “UNLOAD FILAMENT” function to loosen and
remove the filament.
B. Standard Cleaning
1 Use the screwdriver to remove the screw and open the
top cover.
2 Use the cleaning brush to scrub the feed gear back
and forth to remove the chips of filament out of the
gear. Replace the wire after the cleaning is completed.
2 Press the black rubber fixer on top of hole and pull
the guide tube out.
3 Use the cleaning brush to scrub the gear; after removing residues of
filament on the gear, you can insert the guide tube and put the cover
back and then enjoy printing again.
UTILITIES
P 13
da Vinci Jr.2.0 Mix
July 2016
CLEAN NOZZLE
Over time, carbon deposits or filament dust buildup in the nozzle may decrease its performance. It is advised to clean the nozzle
after every time of printing. Also, if the print bed calibration shows “ERR” or if there is any residue on your prints, you may want
to try to clean the nozzle.
For more detailed cleaning methods, please visit Support / FAQ page on website.
A.Feeding Path Cleaning Pin
B.Cleaner Wire
To clean the nozzle:
CLEAN NOZZLE
READY FOR CLEAN
CLEAN NOZZLE
ARE YOU SURE ?
NO
YES
1.Select "YES" to begin.
[ OK ] TO RETURN
2.Wait until the extruder heats up and 3.Hold the cleaning wire with the
moves to the front, and the screen pliers, and carefully pass the wire
shows “READY FOR CLEAN”
through the nozzle openning.
4.Select "OK" to return.
If the cleaning cycle does not unclog the extruder, try cleaning the feeding path by following the steps below.
1.Unload filament correctly (refer to “UNLOAD FILAMENT”).
2.Move the extruder and the print bed to the home position by using the HOME AXES function.
3.Activate “UNLOAD FILAMENT” again and wait until the extruder heats up to 150℃ . (Care should be taken during the operation to
avoid potential burn injuries.)
4.Press the white button
at the back of the
extruder to release it.
5.Lightly press the spring around
the feed hole and remove the
filament guide tube (do not
disconnect the white flat cable)
6.Insert the two leaning pins into the
two feeding paths all the way down at
the same time and “floss” the inside of
the nozzle to pull the residue out.
Z OFFSET (adjust the printer module)
7.After cleaning the feeding
path, reinstall the guide tube
to the top of the extruder and
install the extruder to the
bracket.
The user may use the Z OFFSET function to adjust the gap between the printing nozzle and the printing bed.
Caution: This printer has already been tested and adjusted to the optimal gap between the printing nozzle and printing bed before
shipping. We recommend recording the original settings before carrying out any adjustments.
If the filament comes out from the nozzle, but doesn’t come out for the first layer while printing, please adjust Z-OFFSET.
Z OFFSET settings adjustment
1.The recommended distance between the nozzle and print bed
(with bed tape securely fastened) is 0.3mm.
This should allow two sheets of copy paper to be drawn out
smoothly but six sheets of copy paper cannot be passed.
+[^]
0.1 mm
─[v]
[OK] TO SAVE
Z OFFSET
2.Increase/decrease the value based on a scale of 0.05mm.
Increasing the value will increase the gap between the print module and print bed by 0.05mm
Decreasing the value will also decrease the gap between the print module and print bed by 0.05mm
UTILITIES
P 14
da Vinci Jr.2.0 Mix
July 2016
BUZZER
When the buzzer is turned on, the printer will output an audible signal when a button is pressed, print job is finished, or issue is
detected.
Buzzer is turned on by default. To switch off the buzzer:
buzzer
off
on
on
Select “OFF” and press “OK” to change the setting.
LANGUAGE
You may switch the display language on the printer between English and Japanese.
The default lanague is English. To switch to Japanese:
language
english
ニホンゴ
Select “
en
ニホンゴ "and press “OK” to change the setting.
ENERGY SAVE
LED luminaires are installed in the printing chamber. To save energy consumed, the lighting will go off after idling for 3 minutes (shown
as 03M on the display) by default.
To select a longer time interval:
energy save
off
03m
06m
off
Select “06M” (for auto off after 6 minutes) or “OFF” (for never turn off the LED) and press “OK” to change the setting.
AUTO LEVEL
The printer will adjust the configuration based on the detecting result automatically while "AUTO LEVEL" is enabled. The printing
mode helps to improve printing quality with slower printing speed. You may switch off the function if necessary.
To change the setting of auto-level:
AUTO LEVEL [ON]
OFF
ON
Simply select “OFF” and press “OK” to change the setting.
RESTORE DEFAULT
All settings can be reset to factory default with a few clicks.
To reset all settings at once:
restore default
are you sure
no
yes
Simply select “YES” and press “OK” to reset.
SETTINGS
P 15
da Vinci Jr.2.0 Mix
July 2016
STATISTICS
In “STATISTICS”, you can check the accumulated print time and last print time.
statistics
lifetime
00006h
last time 00h34m
ok
to return
SYSTEM VERSION
Firmware version is shown here. For stable printing performance, it is advised to keep the firmware up to date. To
check for firmware updates, please go to XYZscan/XYZware.
system version
1.1.j
ok
to return
SPOOL STATS
“SPOOL STATISTICS” provides the information on cartridge level (see REMAINING), and the capacity, color and
material of the filament. Press
to read the second page.
SPOOL
stats
remaining
059m
CAPaCiTY
240m
DOWN
NEXT
PAGE
color black
moterial PLA
ok
to return
HELP
The URL to XYZprinting website can be found here. You may go to the website for the latest information, product
documents, tutorial video and more.
HELP
WWW.XYZPRINTING.COM
OK
TO RETURN
MONITOR MODE
"MONITOR MODE" shows the temperature of the extruder. See below for the working temperature for the parts in
different modes.
MONITOR MODE
EXTRUDER
046 C
OK
TO RETURN
INFO
P 16
da Vinci Jr.2.0 Mix
July 2016
PRINTING
This is the unique multicolor function mode of da Vinci Jr. 2.0 Mix. You can choose from "Multicolor Mode" and "Blending
Mode". First, open the XYZware software and then select the printer da Vinci Jr. 2.0 Mix in the settings.
Click "Import" to browse and select the model file to be printed. After loading the file, you can adjust the size,
printing position and angle of the object.
Multicolor Mode - Set different colors for models from different file sources.
These are the
monochromatic colors and
colors toned in different
proportion by the software.
Printing two objects
together is available.
Mixer Mode - Split color blocks according to the height. Each block
contains single color or a set of gradation color blocks.
To print the model in multiple colors at one time, please check the
"Enable Blending Zone" box.
To print the model in
monochromatic color scheme,
please uncheck the box.
Once the Palette function is enabled, the machine will build
filament separation walls and the
printable area will be
14 x 15 x 15 cm (W x D x H).
Add a color node
Object color height
(Add a color node according
to the height of the object.)
This is the color in which the
object will be printed
After setting up the model at the desired size, location and placement, you can also adjust the printing preferences, such
as print speed and layer height by clicking the “Export” icon. Click the “Export” button to slice the file.
When the model is sliced, click on the “Print” button to send the file for printing.
Color Suggestion:
Mixer / Multi-Color Mode
Suggestion
Use both spools as clear filament
limitations
Strongly recommend NOT to use un-clear filament like black, white, blue, and neon green to print.
Using opaque color filaments to blend will overlay the light ones and affect the gradation and multicolor
effect.
Opaque Color
Black, White, Blue, Neon Green
Printing
P 17
da Vinci Jr.2.0 Mix
July 2016
Wireless printing
This chapter introduces how to carry out the setting correctly and to operate the wireless printing function. To understand if your
product is designed with wireless printing function, please refer to the table below.
●da Vinci 1.1 Plus ●da Vinci Jr. 1.0w ●da Vinci Jr. 1.0 3-in-1 ●da Vinci Jr. 2.0 Mix
Pre-setting preparation
1. The network printing function is mainly provided for the Intranet. Please set the printer and the computer in same network domain,
i.e. connecting to the same Wireless Access Point.
2. Before connecting the printer, adjust the set value of the connected Wireless Access Point. For details of setting method, please
refer to the Production Operation Manual or the information provided by the original factory.
3. The Channel Width that can be used by the wireless printing function is 20MHz. Please refer to the Operation Manual compiled
by the original factory for the Wireless Access Point to understand the adjusting method.
4. Please maintain the wireless network function in open status.
5. This machine can support the following connection safety mode. When setting the printer in online status, it is required to input the
Public Key related information.
●WEP
●WPA
●WPA2
(This image is for reference only)
Start the setting
1. Please make sure the connection between computer and printer properly. After completing the connection,
activate the XYZware.
2. Click on the printer monitoring function to open the printer-related information and then click “My Printer” >
"Use Wi-Fi” to access the Wireless Printing Set page.
Wi-Fi Printing
P 18
da Vinci Jr.2.0 Mix
July 2016
3. Please enter the printer name and then press “SCAN” to scroll down the menu for obtaining the exact Wireless Access
Point related information. The description sample will use XYZprinting as the name of Wireless Access Point.
After obtaining the desired information, enter the Public Key password and then press “Use Wi-Fi” and XYZware will
update the online setting value of printer through USB connecting wire.
Note: Please naming printer and Wireless Access Point in English.
Note: If the printer cannot complete the connection with the Access Point within 90 seconds, then XYZware will discontinue the detection. In this case, please check the operation steps and the network are set correctly.
Note: For the password of Public Key, please refer to the information indicated on the Wireless Access Point setting page,
and the length of the password will vary.
4. After completing the printing, please press the “X” key at upper right corner to leave.
To reset the wireless network connection, press “STOP WIRELESS NETWORK/CHANGE SETTING" function keys to
clear the value set before.
INFO>WIFI(SSID)
XYZware secures the IP address of the printer and
the connection is successful.
INFO>IP ADDRESS
At this time, confirm the connection is completed through
the information displayed on the printer.
5. Remove the USB connecting wire and then restart XYZware and the machine is ready for online printing again.
The monitoring function of printer can be used to confirm the
online status and the IP information of the connected printer.
Note: After restarting the printer, IP information will be erased. Please setting again.
Note: The performance of wireless network may be affected due to various environment and power of machine. For
detailed information, please contact the wireless equipment provider or refer to the original factory’s manual. XYZprinting cannot provide tested data for specific equipment.
Wi-Fi Printing
P 19
da Vinci Jr.2.0 Mix
July 2016
da Vinci Junior 2.0 Mix 3D Printer
Model Name
Dimensions
Weight
Display
Language
Connection method
Print Technology
Build Volume
Print resolution
Print module
Nozzle diameter
Filament diameter
Files supported
Operating system
Hardware
requirement
da Vinci Junior 2.0 Mix 3D Printer
16.54 x 16.93 x 14.96 inches (420 x 430 x 380 mm)
26.46 lbs (12kg)
2.6” FSTN LCM
Multi language
USB Wire / SD Card / WiFi
FFF (Fused Filament Fabrication)
5.9 x 5.9 x 5.9 inches (15 x15x15cm)
200 - 400 microns
Dual Feed / Single Nozzle
0.4 mm
1.75 mm
.stl , XYZ Format(.3w)
Windows 7 - 8 above (for PC)
Mac OSX 10.9 64-bit above (for Mac)
X86 32/64-bit compatible PCs with 4GB+ DRAM (for PC)
X86 64-bit compatible Macs with 4GB+ DRAM (for Mac)
Environmentally friendly materials-PLA
PLA filaments are made using polymerized lactic acid, which is
extracted from corn, sugarcane or other sugar-containing crops,
and is regarded as the most environmentally friendly 3D printing
material. Unwanted PLA printed objects can be simply discarded
in the soil where it will naturally decompose.
PLA materials printed at low temperatures are not only suitable for
family settings, its bright texture also makes it a favorite amongst our
clients. You may observe the characteristics of PLA during printing.
• Despite their harmlessness, PLA placed in an environment or water bath exceeding 50 oC (122 oF) will soften and deform.
• Hence, overly humid areas are not suitable storage environments for PLA. We recommend properly sealing and
stashing away unused PLA filaments.
• A sugary smell is often generated when printing with PLA filaments, giving yet another attractive feature.
Specifications
P 20
da Vinci Jr.2.0 Mix
July 2016
The troubleshooting instruction may guide you to fix the problem. If any error persists, please contact customer service.
When an error occurs, please refer to the service code shown on the printer and/or in the software, and check the
suggestions below for troubleshooting.
Technical Support
Website: http://support.xyzprinting.com
Email: US - supportus@xyzprinting.com
EU - supporteu@xyzprinting.com
Other regions - support@xyzprinting.com
Service Code
Symptom
Action
0014
Extruder 1 heating problem
Check connections, reboot the printer.
0030
X-axis movement abnormalities
Check motor/sensor connections.Check sensor position.
0031
Y-axis movement abnormalities
Check motor/sensor connections.Check sensor position.
0032
Z-axis movement abnormalities
Check motor/sensor connections.Check sensor position.
0050
Internal communication error
Reboot the printer.
0051
Internal communication error
Reboot the printer.
0052
Extruder storage error
Replace the extruder.
0054
Extruder not support
Replace the extruder
0057
Unable to detect extruder
Please reinstall the extruder and reconnect the flat cable,
then restart the printer.
Note:
Please retain all original packaging material when shipping your product for warranty
purposes. Shipping without original packaging materials may cause product damaged during
the shipment and may cause chargeable service fees.
Support Details
P 21
da Vinci Jr.2.0 Mix
Other Information
July 2016
1. This product is guaranteed for specific period from the purchase date against any breakdown within the scope of
proper and reasonable usage of their product as defined by XYZ printing.
Presentation of warranty card with the product will ensure free service and repair of inherent faults in the product
within the warranty period. However, the following items are separate and dealt with under conditions of other
related warranty services:
● Printing modules / printing platforms / motor modules
● Attached consumables (including housing, packing materials, power cords, USB cables, coil consumables, user
manuals and software CD's): no warranty is given.
2. To protect your right and interests, please request that the dealer fill in the product information and purchase date
on the product warranty card, and also make sure that they affix their official seal.
3. Please keep this warranty card in a safe place because if it is lost or destroyed a new one will not be issued.
Make sure to present the card if you require any repairs, service or maintenance to the product during the
warranty period.
4. XYZprinting may levy charges under any of the following circumstances:
● Man-made damages: In the case of damage to the product caused by incorrect use, wrong installation,
abnormal wear, physical damage or deformation caused by falls or blows, burnt circuits resulting from actions
form the user, broken or bent interface or pins or any other physical damage to the product caused by misuse.
● Incompatibility issues: anything unconnected with product malfunctions such as conflict with electronic
equipment, expectation of use, noise of operation, speed, discomfort or heat.
● Damage caused by force Majeure (such as lightning strike, fire, earthquake, floods, civil disturbance or war or
any other event beyond human control).
● Any request of warranty service after expiration of the warranty period.
If you need warranty service, please contact the original dealer or send a ticket via XYZprinting website. If you
need more information about our warranty services, please log in to www.xyzprinting.com, select "support (product
support)" where you will find complete details of all the warranty conditions.
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
XYZprinting is not responsible for any radio or television interference caused by using other than recommended cables and
connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of
the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation
instructions and consider removing the no-collocation statement.
Term of Service
P 22
da Vinci Jr.2.0 Mix
July 2016
Warning
● Do not let children operate this device without adult supervision. Electric shock hazard. Moving pars can cause serious
injury.
● Do not place the printer on an unbalanced or unstable surface. Printer may fall or tumble causing harm and/or injury.
Printer may fall or tumble causing harm and/or injury.
● Do not place any objects on top of the printer. Liquids and objects that fall into the printer can lead to printer damage or
safety risks.
● Do not use flammable chemicals or alcohol wipes to clean this device.
● Do not disassemble or replace the printer cover with none XYZprinter covers.
● Do not touch heated surfaces during or after operation. Heated surfaces can cause severe burns.
● Insert and secure the power cord firmly for proper usage and to avoid potential electricity and fire dangers.
● Do not attempt to service the printer beyond the instructions specified in this document. In the case of irrecoverable
problem, contact XYZprinting service center or your sales representative.
Warning!
P 23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising