Indoor Mini-Dome IP Camera User Manual

Indoor Mini-Dome IP Camera User Manual
®
Indoor Mini-Dome IP Camera
User Manual
Product: BLK-IPD101
Please read this manual before using your camera, and always follow the
instructions for safety and proper use. Save this manual for future reference.
BLK-IPD101_CM

CAUTION
Do not operate this camera in environments where the temperature or humidity is outside
the recommended range. Doing so my cause electric shock and shorten the life of the
product.
LEGAL NOTICE
SC Black is a registered trademark of Supercircuits, Inc.
Supercircuits products are designed to meet safety and performance standards with the use of specific
Supercircuits authorized accessories. Supercircuits disclaims liability associated with the use of nonSupercircuits authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is
strictly prohibited by law.
Supercircuits makes no representations concerning the legality of certain product applications such as
the making, transmission, or recording of video and/or audio signals of others without their knowledge
and/or consent. We encourage you to check and comply with all applicable local, state, and federal laws
and regulations before engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Supercircuits, Inc. disclaims any proprietary interest in
trademarks and trade names other than its own.
No part of this document may be reproduced or distributed in any form or by any means without the
express written permission of Supercircuits, Inc.
© 2010 Supercircuits, Inc. All rights reserved.
11000 N. Mopac Expressway, Building 300, Austin, TX 78759
Sales/Support: 1.800.335.9777 | Fax: 1.866.267.9777
ii
www.sc-black.com
Table of Contents
SECTION 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 2 Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Tools you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Find an IP address for your camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.4 Check LAN for default IP address compatibility. . . . . . . . . . . . . . . . . . . . . . 7
2.5 Install IPAdmin Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 Install the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.7 LAN and power connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.8 Configure the camera IP address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9 Setup the camera Basic Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.10Aim, focus, and image quality adjustment. . . . . . . . . . . . . . . . . . . . . . . . . 16
2.11Speaker/microphone setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.12Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SECTION 3 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
APPENDIX A Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
A.1 Camera reset (Reboot camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
A.2 Check firmware version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
A.3 Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
APPENDIX B Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Indoor Mini Dome IP Camera
1
SECTION 1: FEATURES
SECTION 1
Features
The SC Black BLK-IPD101 is a professional, premium-grade mini-dome camera designed for indoor
installation. It features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Gimbal mount
1/4” VGA CMOS sensor
De-interlacing on DSP
Unicast/multicast support
H.264/MPEG4/MJPEG video compression (30 FPS @ D1)
Dual streaming mode
G.711 (µLaw, aLaw)/PCM audio compression
2-way mono audio support
RTSP/ HTTP protocol support
10/100 Base-T ethernet support
Video motion detection support
Video Content Analysis presence, surveillance (optional)
OSD support
Software development kit (SDK) available
Drop cable
Lens
Lens cover
LAN
Power
Audio IN/OUT
Base
Gimbal mount
BLK-IPD101 camera components (without housing)
2
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
SECTION 2
Installation and Setup
2.1 What’s in the box
Your camera includes the following:
•
•
•
•
•
BLK-IPD101 camera
DC power adapter with power plugs for different powering sources
CD mini disk with application software, software manual, and camera manual (this document)
Hex wrench
Two screws for attaching the camera to a mounting surface
2.2 Tools you need
To install the camera, you will need:
•
•
Phillips #2 screwdriver
PC with Microsoft® Windows® XP with SP3 or newer
Depending on how the camera is mounted, you may also need:
•
•
•
•
Hammer
Drill with bits for drilling mounting holes
Wall inserts if attaching the camera to a soft surface
1-1/4” hole saw
2.3 Find an IP address for your camera
Devices attached to an Local Area Network (LAN) are each assigned unique address (IP address) that
they use when sending messages with each other. No two devices on a single Ethernet network can have
the same IP address. Otherwise, conflicts will occur.
Your IP camera is pre-configured with a static IP address, subnet mask, and gateway setting:
IP address:
192.168.0.100
Subnet mask: 255.255.255.0
Gateway:
192.168.0.1
Indoor Mini Dome IP Camera
3
SECTION 2: INSTALLATION AND SETUP
Usually these settings are changed during installation to ones more compliant with the network
configuration.
Use the following procedure to determine a compliant IP address to assign to your camera. If connecting
your camera to a large enterprise network, consult with your network administrator before attaching
the camera to the LAN for network settings to ensure that your camera won’t initially conflict with other
devices. Your network administrator should also setup WAN (Internet) access to the camera.
If you encounter a problem and need to contact Supercircuits Support, first complete the chart in step
1 about your Computer (PC) and camera network settings, if possible. The Support team will need this
information to provide assistance.
1.
4
At a PC attached to the same LAN that will be shared with your camera, determine the IP address,
subnet mask, and default gateway of your PC and record it in Table 1. To find this information, do
the following at the Windows desktop:
a.
Hold down the Windows key and press r to open the Run dialog box.
b.
Type cmd in the entry field and click OK to open the DOS command window.
c.
At the command prompt, enter ipconfig. The PC will display Ethernet data associated with
your Ethernet adapter.
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
Example: Typical use of ipconfig in Windows XP
d.
Enter the IP Address, Subnet Mask, and Default Gateway for your PC’s Ethernet adapter into
Table 1.
The Ethernet adapter data you see by using ipconfig will probably be different from that
shown in the example above. If you are using Windows Vista or Windows 7, the IP address
is identified as the “IPv4 Address.”
NOTE
Table 1. PC/Camera network settings
Computer (PC)
Camera
IP Address
Subnet Mask
Default Gateway

CAUTION
2.
If connecting your camera to an enterprise network, consult with your network
administrator for the camera IP address, subnet mask, and default gateway.
At your PC, find an IP address on your network that is not in use:
a.
Write down the EXACT IP address of your PC up to the third/last period. Using the example
shown above, this expression is: 192.168.1.
Indoor Mini Dome IP Camera
5
SECTION 2: INSTALLATION AND SETUP
b.
After the third period, include any number between 1 and 256 that is different from the one
in your PC’s IP address, 168. As a first try, let’s choose 200, which will form the IP address
192.168.1.200.
c.
Next, use the ping command in the DOS window to see if this IP address is in use on your
network. The format of the ping command is:
ping <IP address>
To test this IP address, enter ping 192.168.1.200. Any reply received from the ping indicates
that a device on the network is already using this IP address and you can connect to it.
In the example shown above, the message “Reply from 192.168.1.200: ...” indicates that your
PC can reach the device with that IP address, and that address is in use.
d.
6
Since the ping test of the IP address we tried showed the address was in use, try another
number between 1 and 256. For example, let’s ping 192.168.1.201. At the DOS prompt,
enter: ping 192.168.1.201
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
e.
In this test, the message “Request timed out” indicates that your PC cannot reach the device
with that IP address, and that address is probably not in use. Enter this number into Table 1.
If this test indicated that this IP address is in use, try other IP address using the steps above
until an unused address is found.
2.4 Check LAN for default IP address compatibility
Because all SC Black cameras and encoders are factory configured with the static IP address
192.168.0.100, check the LAN before connecting your camera to ensure that network conflicts won’t
occur.
At a Microsoft Windows computer attached to the LAN subnet where the camera will be connected, open
a Command Prompt window and enter:
ping 192.168.0.100
The “Request timed out” response indicates that the IP address is not in use and the camera can be
connected without causing errors.
2.5 Install IPAdmin Tool
The IPAdmin Tool, included on the CD mini disk, will discover cameras installed on your network and
enable you to perform the initial network setup for each SC Black camera. After the camera is setup on
the network, the Microsoft® Internet Explorer web browser can be used to see video from the camera,
set the camera’s password, date, and time, finalize camera hardware adjustments, and configure the
camera for functional requirements.
The IPAdmin Tool can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating system.
To use this utility for the initial setup of your camera, your computer must be connected to the same
network segment as your camera.
Indoor Mini Dome IP Camera
7
SECTION 2: INSTALLATION AND SETUP
To install the IPAdmin Tool, do the following:
1.
Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the
CD in a Windows Explorer window.
2.
Establish a directory on your computer hard drive for the IPAdmin Tool application.
3.
Copy the files IPAdminTool.exe and IPAdminTool.dll to your new directory.
2.6 Install the camera
1.
Separate the base from the camera housing by turning the housing bezel counter-clockwise about
30º and lifting it off the base.
2.
Determine where the camera will be mounted and record the MAC address of the camera. The
MAC address can be found on the label on the base of the camera. Record the information in the
following table.
Location:
MAC address:
3.
Using the base as a template, mark the location of the two mounting screw holes.
4.
Drill mounting screw holes into the mounting surface:
——
If the mounting surface is a soft material, such as a drywall, drill and install drywall inserts for
the mounting screws.
OR
——
If the mounting surface is a very soft material, such as ceiling tile, place a wood block behind
the tile and drill holes for mounting screws long enough to secure the base to the block.
OR
——
8
If mounting the camera on a hard surface, such as wood, drill the mounting screw holes into
the surface before attaching the camera.
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
Mounting
screw
holes
Hole for
drop cable
Wall inserts
Cable
guide
Screws
Camera installation
5.
Determine the cable routing. If the cable drop cable is to be routed through a hole covered by the
camera base, perform the following steps. If the cable will be routed through a cable guide in the
base to a nearby connector box, skip to step 9.
6.
Drill a 1-1/4” hole through the mounting surface between the mounting screw holes.
7.
Route the camera drop cable through the 1-1/4” hole.
8.
While holding the camera base in its mounting position, secure it to the surface with screws.
9.
Press the camera drop cable into the cable guide in the base.
10. While holding the camera base in its mounting position, secure it to the surface with screws.
2.7 LAN and power connections
11. Attach the power plug appropriate for your powering source to the power adapter.
Indoor Mini Dome IP Camera
9
SECTION 2: INSTALLATION AND SETUP
12. Attach the network LAN, audio in/out (AIN, AOUT), and power (DC12V) cables to the camera drop
cable as required.
LAN
DC12V Adapter
2.8 Configure the camera IP address
1.
Open the directory where you installed IPAdmin Tool. Double click the file IPAdminTool.exe to start
the application. When IPAdmin Tool starts, it will discover all of the IP cameras it supports that exist
on the network. The discovery process may take a few minutes.
2.
In the Product list, find the entry with the same MAC address as the camera you installed. If the
camera is not shown, click Refresh repeatedly to update the list.
3.
Right click on the entry for your camera and select IP Address.
10
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
IP Setup window
4.
In the IP Setup window:
a.
Select the Static option if it is not already selected. This option is required if video from the
camera will be recorded by a network DVR, or if you want to view video from the camera
across a WAN (Internet).
b.
Enter the IP address for your camera from Table 1 into the IP address field.
c.
Enter the subnet mask for your computer from Table 1 into the Subnet Mask field.
d.
Click Setup. A Login window will open.
5.
In the Login window, enter the ID (user name) and PW (password) for your camera and click Login.
After clicking Login, the IP Setup window will close. The default administrator ID and PW values are
root and pass.
6.
In the IPAdmin Tool window, click Refresh and verify that the entry for your camera now shows the
new IP address.
Indoor Mini Dome IP Camera
11
SECTION 2: INSTALLATION AND SETUP
2.9 Setup the camera Basic Configuration
In this procedure, use the Internet Explorer (IE) browser to setup the camera administrator and user
passwords, date, and time.
1.
Open the IE browser.
2.
In the URL field (Internet address), enter the IP address for your camera in the format:
http://<IP address>/
where <IP address> is the IP address of your camera. Following the example earlier in this guide,
the entry would be: http://192.168.1.201
3.
If prompted to install an ActiveX control such as AxAll.cab (publisher Cap Co), follow the screen
prompts to install the software.
IE prompt to install ActiveX control
12
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
Typical initial camera view
NOTE
4.
If, after logging into your camera, you cannot see live video and the message:
“Can not Create XMLDOMDocument Install MSXML4.0” appears, download and install
the MS XML 4.0 library. This library can be found at:
http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B-B4F2-46DAB4B6-C5D7485F2B42&displaylang=en
In the camera window, click the SETUP link in the upper right corner of the window. Enter the User
name and Password for the camera, and click OK. The default administrator values are:
User Name: root
Password: pass
The Basic Configuration window will open.
Indoor Mini Dome IP Camera
13
SECTION 2: INSTALLATION AND SETUP
5.
Under the Basic Configuration menu, click Date & Time.
6.
In the Date & Time Setting options:
14
a.
Select the Time Zone you prefer.
b.
Select the synchronization method, or click the Set manually bullet and enter the appropriate
information.
c.
Select the Sync Source and Interval you prefer.
d.
Click Apply.
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
7.
In the Basic Configuration window, click Users.
8.
In the User List, click root, and then click Modify and follow the prompts. Setup the administrator
user with a new password and click OK.
Indoor Mini Dome IP Camera
15
SECTION 2: INSTALLATION AND SETUP
9.
In the Users menu, click Apply, then click OK to restart the webserver (if you wish to do so at this
time).
10. Click Add to include other administrators, operators or viewers to the user list. Follow the screen
prompts to complete the entries.
11. Click VIEW in the upper right corner of the window to return to the camera live view.
2.10 Aim, focus, and image quality adjustment
2.10.1 Aim
The camera mount allows the camera to be rotated on three axis to set the horizon alignment, horizontal
direction, and up/down position of the video frame.
Up/down position
Horizontal direction
Horizon alignment
Set screw
1.
While observing video from the camera, set the horizon alignment by rotating camera module
bracket on its horizontal axis.
2.
Set the horizontal direction by rotating camera assembly on its vertical axis.
16
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
3.
Loosen the set screw on the side of the camera assembly and rotate the camera to adjust the up/
down position of the camera video. Tighten the set screw to lock the up/down position in place.
4.
If necessary, make additional adjustments to these settings to perfect the frame of the video.
2.10.2 Focus
Camera focus adjustment is performed by rotating the camera lens. A set screw locks the lens in
position.
Lens cover
Latch
Camera lens
Focus set screw
1.
Gently lift the lens cover securing latch on the side of the camera assembly to release the cover and
remove it from the camera.
2.
Find the set screw on the side of the camera lens and loosen it, if necessary, with the hex wrench
provided.
3.
While observing video from the camera, rotate the camera lens until the best focus is achieved.
4.
Tighten the lens set screw.
5.
Replace the camera lens cover.
6.
Re-install the camera housing.
2.10.3 Image quality adjustments
Adjustments to the image brightness, contrast, hue, saturation, and sharpness are performed through
the web browser:
Indoor Mini Dome IP Camera
17
SECTION 2: INSTALLATION AND SETUP
1.
From the VIEW window, click: SETUP > Video & Audio > Video-In
2.
Scroll to the bottom of the screen and click the PREVIEW button. Follow the screen instructions to
open the camera view in another IE window.
3.
While observing the video in the PREVIEW window, adjust the values for brightness, contrast, hue,
saturation, sharpness, and/or other parameters on screen. Click Apply to see the effect of the
change. Make any necessary adjustments to produce the best video image.
4.
Close the PREVIEW window and click VIEW to return to the normal viewing window.
2.11 Speaker/microphone setup
Verify the functionality of the speaker and microphone setup at the camera, and adjust volume levels.
1.
Re-install the camera housing. Ensure that the dome window is over the camera lens.
2.
Connect the AOUT line to a preamplified speaker at the camera.
3.
Connect the AIN line to a microphone.
18
www.sc-black.com
SECTION 2: INSTALLATION AND SETUP
4.
On the View screen, click SETUP > Video & Audio > Audio to open the Bi-directional Audio
Settings menu.
5.
In the Bi-directional Audio Settings menu, click the checkboxes to select “Listen to the audio from
server with setting below” and “Talk to the speakers of server”.
6.
Click Apply, and then click VIEW to return to the camera view screen.
7.
On the VIEW screen, check the SPK and MIC options to enable the speaker at the camera and the
microphone on your computer.
8.
At your computer, listen for sounds from the microphone at the camera. If necessary, adjust the
volume from the camera. Click:
SETUP > Video & Audio > Audio
to re-open the Bi-directional Audio Settings menu. In the Listen frame, adjust the volume to the
preferred level. Click Apply.
Indoor Mini Dome IP Camera
19
SECTION 2: INSTALLATION AND SETUP
9.
Use a microphone at your PC to send audio to the camera speakers. Verify that your microphone
audio is heard at the speaker.
To adjust the speaker volume go to the Bi-directional Audio Settings menu. In the Talk to frame,
adjust the volume to the preferred level. Click Apply.
2.12 Cleaning
Clean the camera housing with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.

CAUTION
20
Do not use benzene, thinner or other chemical products on the camera assembly; these
may dissolve the paint and promote damage of the surfaces. Before using any chemical
product, read the accompanying instructions carefully.
www.sc-black.com
SECTION 3: SPECIFICATIONS
SECTION 3
Specifications
Table 2.Specifications
Camera Module
CMOS
Image Sensor
1/4” VGA CMOS
Effective Pixels
640 x 480
Scanning system
Progressive Scan
Horizontal Resolution
550 TV Lines
Min. Illumination
3 Lux Color 0.1 Lux DSS On
Lens
Focal Length 3.6 mm, F.# 2.0, Board type, Lens for Security Camera
Shutter Speed
1/60 ~ 1/100,000
Day & Night
Not Supported
Video
Compression Format
H.264, MPEG-4, MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
D1, CIF, VGA, QCIF
Compression FPS
30 FPS @ D1
Deinterlacing
Supported (DSP)
Motion Detection
Supported
OSD
Supported (DSP)
Burnt-in Text (Digital)
Supported (DSP)
Output
Not Available
Audio
Input/output
1/1 channel
Compression Format
G.711
Digital Input/output
Not Supported
Network
10/100 Base-T
Power over Ethernet
Not Available
Protocol
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP, SNTP, mDNS, UPnP, SMTP,
SOCK, IGMP, DHCP, FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH
Material
Polycarbonate
Dimensions
Housing: 4.88 in (D) x 3.94 in (H), Dome: 3.84 in radius
Color
Black
Indoor Mini Dome IP Camera
21
SECTION 3: SPECIFICATIONS
Electrical characteristics
Video Output
1 Vp-p, 75 Ω
Audio Input
Line-in, 1.43 Vp-p (Min 1.35 Vp-p, max 1.49 Vp-p), 39 KΩ
Audio Output
Line-out, 46 mW power, 16 Ω
Power Source (approx.)
12 V DC, 290 mA
Environmental conditions
Operating Temperature
32˚F ~ 122 ˚F (0 ˚C ~ 50 ˚C)
Operating Humidity
Up to 85% RH
Table 3.Video Content Analysis (optional)
VCA Presence
High Performance
Advanced Tracking Algorithm, Low False Alarm Rate
Easy to Use
Intuitive Web Browser Interface
Detection Zones
Multi-segment Polygons and Lines
On-screen Display
Real-time Display of Tracking Data and Events
Burnt-in Annotation
Stream or Analog video out (Analog video out support can vary depending on the device model,
hardware version, and the firmware version)
VCA Surveillance
Detection Behavior
Camera Tampering, Direction, Stopping, Loitering, Entering, Exiting, Appear, and Disappear Filters
3D Behavior
Perspective Corrected Size and Speed Filters
Statistics
Counting Functions and Other Statistics
Meta Data
Binary XML Format
Image Stabilization
Electronic Stabilization
22
Removes Camera Sway
www.sc-black.com
APPENDIX A: TROUBLESHOOTING
APPENDIX A
Troubleshooting
A.1 Camera reset (Reboot camera)
The IPAdmin Tool includes a reboot feature for your camera. To reboot the camera:
1.
Start the IPAdmin Tool.
2.
Find the entry for the camera you want to reboot and click it to select (highlight) it.
3.
Click the Reboot button and enter the administrator ID and PW.
NOTE
4.
The reboot process lasts about 2 minutes, during which the camera will not respond to
the IPAdmin Tool.
Click Refresh to re-discover the camera.
A.2 Check firmware version
Firmware is software embedded in the camera that determines many of its features and functionality.
The current firmware version number in your camera can be found by viewing video from the camera in
IE, and then clicking Setup > About > Version. Contact Supercircuits Support for firmware updates.
A.3 Support
If you cannot resolve an issue, please contact Supercircuits Support at 1.800.335.9777 for assistance.
When you contact support, please provide the server reports, log file and a brief description of the
problem, if possible.
•
To generate a server reports, enter the following into the IE address field:
https://<IP ADDRESS>/nvc-cgi/admin/param.cgi?action=list
- and https://<IP ADDRESS>/nvc-cgi/admin/vca.cgi?action=list
where <IP ADDRESS> is the IP address of your camera. The server report contains important
Indoor Mini Dome IP Camera
23
APPENDIX A: TROUBLESHOOTING
information about the device, as well as a list of the current parameters.
•
To generate a log report, use IE to log into the unit. In the View screen, click the following items,
entering security information when required:
SETUP > Maintenance > System Log > LOG LIST
Click the name of the Log List of interest to open it.
24
www.sc-black.com
APPENDIX B: DIMENSIONS
APPENDIX B
Dimensions
Indoor Mini Dome IP Camera
25
26
www.sc-black.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising