always - makita india
Satisfy Professional's Needs
Comparison of Efficiency
Note:
1. The test results depend to a great extent on the hardness of the
material, etc.
2. Numbers in the charts below are relative values when the
capacities of Competitor "B" model are indexed at 100.
3. Chipped concrete in vertical down application using ø1.5mm2 x
50m cord reel, and measured the amount of concrete removed.
Comparison of Vibration level* and Time to reach
ELV (Exposure Limit of Vibration)**
*It is known as the tri-axial value and value at Directive of A(8).
**It means the maximum amount of vibration that an operator
may be exposed to on any single day.
Time to reach
ELV (min)
Test material: Concrete with compressive strength of 40N/mm2
130
Makita
HM1213C
0
90
100
110
120
130
large
200
250
245
min
15.5
m/s2
25min
22m/s2
17m/s2
42min
Competitor "H"
small
150
50min
Competitor "B"
95
Competitor "H"
100
7.0m/s2
Makita HM1203C
100
Competitor "B"
50
Makita
HM1213C
110
Makita HM1203C
Demolition Hammer
HM1213C/ HM1203C
See the Result of AVT
Vibration level
(m/s2)
0
5
10
15
20
Adapted for
SDS-MAX bits
ALWAYS
low Vibration
Anti Vibration Technology and
Suppression of motor speed
during no-load
(HM1213C only)
25
Accessories
Bull point
Scaling chisel
(For demolishing concrete)
(A wide chisel for chipping
away scale of dried concrete
spatter)
Bushing tool
(For concrete surface
removal)
Length(mm)
Type
Part No.
280
-
A-80787
400
-
A-80793
Size(mm)
Type
Part No.
Size(mm)
Type
Part No.
600
-
A-87476
50 x 400
-
A-80824
67 x 67
•
A-19881
Self-Sharpening Bull Point
Length(mm)
Type
Part No.
400
-
B-10621
Cold chisel
(For chipping, edging,
channeling and breaking
away larger chunks of concrete)
• Use with shank (A-19897)
Scaling chisel (for Tile)
Rammer
These items are available on
request. Contact us for the
minimum order quantity.
(For tamping)
• Use with shank (A-19897)
Size(mm)
Type
Part No.
50 x 300
-
A-80830
Dia.
Dia (mm)
Type
Part No.
140
•
A-19875
Clay spade
Grease vessel set 100ml
(for bit)
Size(mm)
Type
Part No.
25 x 280
-
A-80802
25 x 400
-
A-80818
Size(mm)
Type
Part No.
Part No.
24 x 600
-
A-87482
105 x 400
-
A-17653
194683-7
Demolition Hammer
HM1213C / HM1203C
Double Insulation
Variable Speed
Photo: HM1213C
Constant Speed
Soft Start
Adapted for SDS-MAX bits
Continuous rating Input
Impacts per minute (ipm)
Dimensions
(L x W x H)
Net weight
Power supply cord
171
HM1213C
1,510W
950-1,900
576 x 149 x 265mm
(22-3/4" x 5-7/8" x 10-3/8")
*10.8kg (23.6lbs)
5.0m (16.4ft)
HM1203C
1,510W
950 - 1,900
576 x 128 x 265mm
(22-3/4" x 5" x 10-3/8")
*9.7kg (21.4lbs)
5.0m (16.4ft)
Learned from the Mother Earth
SDS-MAX Shank
Carrying Case
Photo: HM1203C
*weight according to EPTA-Procedure 01/2003
Standard Equipment Bull Point, Bit Grease, Side Handle
Items of standard equipment and specifications may vary by country or area.
Makita Power Tools India Pvt. Ltd.
Unit II Sy. Nos. 93/3 & 93/4, Koralur village, Kasaba Hobli, Hoskote Taluk,
Bangalore - 560 067, INDIA. Tel: +91-80-2205-8200, Fax: +91-80-2854-9007
Email: sales@makita.in Website: www.makita.in
HM1213C only
Dominate the Job Site
with Makita’s Low Vibration Demolition Hammer
Anti Vibration Technology
Under load
A
B
(HM1213C only)
Active dynamic vibration absorber
Shift of air pressure in crank room and barrel room "actively"
controls balancer to move opposite of piston.
Balancer
Air
A
Piston
B
swivels 360° to your desired position.
8 different settings (back and forth).
Air
Piston
Vibration Absorbing Grip
Spring loaded hinged grip
absorbs vibration.
D-shaped side handle
Air
Air
Balancer
Easy-to-operate
slide switch
Spring
Hinge
ALWAYS
low Vibration
One-touch sliding chuck
for easy bit changes
During no-load
12 bit angle settings
Suppression of motor speed
Photo : HM1213C
Adapted for
SDS-MAX bits
Rubberized soft grip
provides more comfort and control.
Long size carbon brush
for extended service life
- reduces vibration of tool body when idling,
Motor
accordingly decreases the amount of
speed
vibration to operator’s hands during
a day’s operation.
- minimizes deflection of bit tip from aiming
point when starting chipping.
During no-load
Under load
Suppression of
motor speed
when starting chipping
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising