READ AND SAVE THESE INSTRUCTIONS MODEL 103023

READ AND SAVE THESE INSTRUCTIONS MODEL 103023
MODEL 103023
WOOD HOOD KIT
READ AND SAVE THESE INSTRUCTIONS
!
FOR DOMESTIC COOKING ONLY
!
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10.This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite.
2. Always turn hood ON when cooking at high heat or when cooking flaming
foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already know how
to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
3. For best capture of cooking impurities, your range hood should be
mounted so that the bottom of the hood is 18-24” above the cooking
surface.
4. Please read specification label on product for further information and
requirements.
This wood hood kit can be easily installed by following three basic
steps:
• Install a wood mounting frame in hood
• Install the hood kit
• Mount the hood in place on the wall
This wood hood kit requires the previous installation of Broan
Model 103123 Rough-in Kit including:
Use 3¼" x
10" duct and
a 900 elbow
to exhaust
horizontally.
16”
• 120 VAC electrical wiring
x 10” metal ductwork (extending down to 16” above bottom
• 3¼”
of wood hood)
16” MIN.
19¼” MAX.
INSTALLER: Leave this manual with the homeowner.
HOMEOWNER: Use and care information on page 5.
INSTALL MOUNTING FRAME
SHEET METAL
NUT
MOUNT BLOWER HOUSING
(continued)
BRACKETS TO
BE FLUSH WITH
WOOD FRAMING
PUSH HOUSING IN
THIS DIRECTION
#10 x 7/8
1/4-20 x 1/2
DUCT
OPENING
C
L


TO CENTER LINE
OF SLOTS
IN BRACKETS
FRONT OF
WOOD HOOD
BACK OF
WOOD HOOD
4. Fasten housing to mounting brackets with four (4) screws. Push
housing toward top of wood hood, as far as mounting slots will
allow. Make sure duct opening is toward back of hood.
LENGTH OF
FRONT & REAR BOARDS
TO BE INSIDE WIDTH
OF WOOD HOOD
LENGTH OF (2)
SIDE FRAMING
PIECES
(Mounting Brackets must
fit inside frame)
INSTALL LINER
(for 30” Wood Hood)
1. Construct a wood frame which will fit the hood and allow the
ductwork to line up with damper assembly. Attach the mounting brackets with the sheet metal nuts toward the hood front.
Secure frame to hood using dimensions shown.
CLEARANCE
HOLE
#8 x 3/8
MOUNT BLOWER HOUSING
SHEET
METAL
NUT
DAMPER ASSEMBLY
SHEET METAL SCREW
CLEARANCE
HOLE
BLOWER HOUSING
WHEEL
28- DIM INS
1/4 EN IDE
” to SIO
28- N
7/8
”
BLOWER ASSEMBLY
MOUNTING ROD
KNURLED NUT
FRONT OF
WOOD HOOD
2. Remove the blower assembly by unplugging it, loosening the
knurled nuts and pivoting mounting rods away from blower.
3. Remove the damper assembly by unscrewing the two (2) sheet
metal screws and sliding it back through the housing.
2
5. Make sure two (2) clearance holes in liner are lined up with
sheet metal nuts on mounting brackets. Then screw liner pieces
to mounting frame in nine (9) places.
INSTALL LINER (continued)
MOUNT HOOD (continued)
#8 x ½
NOTE:
Lamp Receptacles are
toward
REAR of hood.
6. Fasten the two, adjustable front liners to hood with eight (8)
screws provided. Use a 7/ 64” dia. drill bit to drill through liners
and fasten them securely where they overlap.
10. Plug in control unit and fasten to hood as shown.
MOUNT HOOD
POWER
CORD
DUCT
OPENING
NOTE:
Filter Tabs
are toward
REAR of hood.
11. Install aluminum filter. Rotate two (2) retaining clips (on the
hood liner) to hold filter in place.
7. Secure hood to wall, soffit or cabinets as appropriate.
12. Install an F20T12 fluorescent tube (not supplied).
8. Reach up through duct opening and connect power cord to
blower housing.
9. Slide damper assembly up into ductwork and refasten to blower
housing (using the two (2) screws removed in Step 3). Reinstall
blower assembly and plug it in.
3
WOOD HOODS GREATER THAN
30” WIDE - UP TO 42” WIDE
WIRING DIAGRAM
For wood hood applications over 30” (and up to 42”) - add
two (2) custom metal fillers (not supplied), as shown above, to
provide the proper width dimension. The exact filler dimension is
determined from the wood hood requirements.
NOTE: For 36” wood hood application - replacement side liners
(97009790) are available and provide overall width of 34-1/4” to
34-7/8”.
DETERMINE
FROM WIDTH
OF HOOD
FILLER
SIDE
LINER
TOP
LINER
SIDE
LINER
4
USE AND CARE
SERVICE
CAUTION
ALWAYS DISCONNECT ELECTRIC POWER SUPPLY TO
HOOD BEFORE SERVICING.
OPERATION
For best results, always turn on your hood before you begin
cooking. Let hood run for a few minutes after you turn off range to
allow hood to clear the air in the kitchen.
Refer to page 4 for wiring diagram.
Your hood uses an F20T12 fluorescent tube, available at most
hardware stores or home centers.
If tube flickers or does not light, check the prongs on ends of tube to
make sure that they are properly seated in tube holders. Slide prongs
into holders and rotate tube so that holders grip prongs and hold tube
in place. If tube continues to flicker or does not light, replace tube.
If ends of tube light but center does not, the starter may be defective. Your hood uses an FS-2 starter, located on underside of control
unit. Remove old starter by pushing it in and turning it clockwise.
Purchase a new starter at your local hardware store or home center,
and install it by pushing it in and turning clockwise.
If tube still does not light, order a 97007428 Ballast Transformer Kit
from your Broan Distributor or from the Broan Service Department.
Write Broan Mfg. Co., Inc., P. O. Box 140, Hartford, WI 53027.
SPEED CONTROL
The speed control allows unlimited selection of blower speeds and
sound levels. The control turns the blower on to high speed and
dials down to low speeds.
HEAT SENTRY ™
Your hood is equipped with a Heat Sentry™ thermostat. This thermostat is a device that will turn or speed up the blower if it senses
excess heat above the cooking surface.
If blower is not on, or if it is running at low speed, the Heat Sentry™ will
override the normal blower control and turn blower on to high speed.
The blower will run until temperatures drop to normal levels. The
blower will then return to its original setting.
LIGHT
TO REMOVE BLOWER FOR SERVICE
The light switch is located just to the left of the speed control.
1. Remove fluorescent tube.
CLEANING
2. Rotate filter retaining clips out of way and remove filter.
CAUTION
ALWAYS DISCONNECT ELECTRIC POWER SUPPLY TO
HOOD BEFORE CLEANING.
Clean hood with a mild detergent suitable for painted surfaces. DO
NOT USE ABRASIVE CLOTH, STEEL WOOL PADS OR SCOURING POWDERS.
To clean blower, remove filter and vacuum blower. Blower motor is
lifetime lubricated and never needs oiling. Do not immerse blower
in water.
FILTER
The aluminum filter in your hood should be cleaned frequently with
detergent to avoid grease buildup. The filter is dishwasher safe. To
remove filter, rotate retaining clips on either side of filter opening
out of the way and pull filter out of hood. When replacing filter, make
sure pull tabs on filter are toward the bottom and to the back of hood.
BLOWER
HOW TO AVOID A COMMON RANGE-TOP GREASE FIRE
Your range hood provides a protective barrier between the
cooking surface and the cabinets.
Keep fan, filters and grease laden surfaces CLEAN according
to instructions.
Always turn hood ON when cooking at high heat to keep the
cooking area and the hood cooler.
Use high heat settings only when necessary.
Never leave cooking surface unattended. Boil-over causes
smoking and greasy spillovers that may ignite.
Always use adequate-sized utensils.
If preparing flaming foods, such as Cherries Jubilee, always
turn hood ON to HIGH to prevent a high heat situation which
can cause damage or fire.
KNURLED NUT
3. Unplug blower and back off knurled nuts to ends of blower mounting rods. Do not remove nuts completely from rods. Support
blower with one hand, slip rods out of brackets and swing them
out of the way. Do not grasp blower by blower wheels. Wheels
may be damaged.
4. Reinstall blower by slipping blower mounting rods into mounting brackets. Tighten knurled nuts securely, and plug blower in.
Replace filter and fluorescent tubes.
HOW TO EXTINGUISH A COMMON RANGE-TOP GREASE
FIRE
Never pick up a flaming pan. If dropped, flames can spread
quickly.
DO NOT USE WATER! A violent steam explosion may result.
Wet dishcloths or towels are also dangerous.
Smother flames with a close fitting lid, cookie sheet or metal
tray.
Flaming grease can also be extinguished with baking soda
or a multi-purpose dry chemical extinguisher.
Turn off surface units - if you can do so without getting burned.
5
SERVICE PARTS
Model 103023 Wood Hood Kit
KEYPART
NO.
NO.
DESCRIPTION
97010327
Complete Blower Assembly (Includes Key Nos.
12, 13, 14, 15, 16, 19 & 20)
1
97009818 Control Box Wiring Harness
2
97006078 Damper Assembly (Includes Key Nos. 3 & 4)
3
98005221 Damper Flap
4
99100379 Damper Bushing (2 Required)
5
97007406
Blower Housing Wiring Harness
6
97007487
Blower Housing
7
93270619 Harness Clip
8
99200202 ¼-20 Machine Screw (4 Required)
9
97007488
Blower Box Mounting Bracket (2 Required)
10
99260473 Sheet Metal Nut #10-24 U-Type (2 Required)*
11
99020138
Blower Wheel - Clockwise
12
99170245 #8-18 Tapping Screw (10 Required)
13
98005212 Motor Retaining Ring (2 Required)
14
99100491 Rubber Motor Mount (4 Required)
15 97010736 Motor
16
99420464 Blower Mounting Rod (2 Required)
17
99260476 Blower Mounting Rod Nut (2 Required)
18
97007314 Blower Scroll Housing
19
99020139
Blower Wheel - Counterclockwise
20
97007486
Liner Front Piece (2 Required)
21
98006455 Liner Side Piece - Right Hand
22
97013583
Liner Top Piece
25
99150470 #8AB Sheet Metal Screw (13 Required)
26
98006454 Liner Side Piece - Left Hand
**
97009790 Side Liners for 36” Wide Hood - LH & RH
(Not Included)
27
97007725 Aluminum Filter
28
99150491 #8B Sheet Metal Screw (2 Required)
29
97007726 Control Housing Cover
30
97007428
Ballast Transformer Kit
31
99030132
Speed Control
32
99260481 Sheet Metal Nut, #10-16 U-Type*
33
99270670 Ground Clip
34
97007424
Heat Sentry™ Bracket Assembly
35
97009817 Control Housing
36
99270550 Fluorescent Lampholder (2 Required)
37
98005860 Lampholder Retainer (2 Required)
38
99150490 #10B Sheet Metal Screw (2 Required)
39 99360118 Knob
40
99260491 3/8 Hex Nut
41
99030310 Light Switch
42
99270553 Fluorescent Starter FS-2*
43
99270650 Fluorescent Starter Base
44
99400054 Hole Plug
45
99160319
#6-32 x 3/8 Pan Head Machine Screw
(4 Required)*
46 99150591 #10-12 x .625 Slotted Pan Head Sheet Metal
Screw (8 Required)*
47
99160356 #10-24 Machine Screw (2 Required)*
48
99150492 #8AB x ½ Sheet Metal Screw (8 Required)*
**
97007489
Parts Bag (Includes Key Nos. 8, 25, 46, 47 & 48)
* Standard Hardware. May be purchased locally.
**Not Illustrated
6
SERVICE PARTS
Model 103023 Wood Hood Kit
11
10
2
8
3
12
12
13
4
17
13
48
28
7
Limited Warranty
Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period of one (1) year from the date of original purchase.
The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited warranty shall be the remainder of the original warranty period.
This warranty does not cover speed controls, fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof caps, wall caps and other accessories for ducting that may be purchased separately and installed with the Product. This warranty also does not cover (a) normal maintenance and service, (b) normal
wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage
or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (e) any Product
that has been moved from its original point of installation, (f) damage caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish,
(i) Products in commercial or nonresidential use, or (j) damage caused by fire, flood or other act of God. This warranty covers only Products sold to original consumers
in the United States by the Company or U.S. distributors authorized by the Company.
This warranty supersedes all prior warranties and is not transferable from the original consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective products. The foregoing warranties are exclusive
and in lieu of any other warranties, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the
extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the period specified for the express
warranty above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or written description
of the Product is for the sole purpose of identifying it and shall not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if any provision is
held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the remainder of such provision
or the other remaining provisions of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge, any Product
or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or other freight
charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to the Company, as instructed by the Company, you must
properly pack the Product or part—the Company is not responsible for damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or
remanufactured Products or parts in the warranty repair or replacement process. Such Products and parts will be comparable in function and performance to an original
Product or part and warranted for the remainder of the original warranty period.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT THE COMPANY’S OPTION, SHALL BE YOUR
SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE
FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights, which vary from state to state.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of field service travel
and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty will not constitute a waiver of such terms,
limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with the Company’s prior
written permission.
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within seven (7) days
of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty, then the terms of the
Company’s most current written limited warranty for your particular product will control. The most current limited written warranties for the Company’s products can be
found at www.broan.com .
Broan-NuTone LLC 926 West State Street Hartford, WI 53027 www.broan.com 800-637-1453
99040917AA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising