KD-34XBR960 - yourpdfguides.com: Instruction manual

KD-34XBR960 - yourpdfguides.com: Instruction manual
You can read the recommendations in the user guide, the technical guide or the installation guide for SONY KD-34XBR960. You'll
find the answers to all your questions on the SONY KD-34XBR960 in the user manual (information, specifications, safety advice,
size, accessories, etc.). Detailed instructions for use are in the User's Guide.
User manual SONY KD-34XBR960
User guide SONY KD-34XBR960
Operating instructions SONY KD-34XBR960
Instructions for use SONY KD-34XBR960
Instruction manual SONY KD-34XBR960
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
Manual abstract:
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol
is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance. Reorient or relocate the receiving antennas. Increase the separation between the equipment and receiver.
@@Consult the dealer or an experienced radio/TV technician for help. @@@@The AC power cord is attached to the rear of the TV with hooks. Do not
attempt to remove the cord from these hooks.
@@If a fixed (non-moving) pattern is left on the screen for long periods of time at a high brightness or contrast setting, the image can be permanently
imprinted onto the screen. Continuously watching the same program can cause the imprint of station logos onto the TV screen. These types of imprints are not
covered by your warranty because they are the result of misuse. Owner's Record The model and serial numbers are provided on the front of this instruction
manual and at the rear of the TV. Refer to them whenever you call upon your Sony dealer regarding this product.
Note This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a
cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain
advanced and interactive digital cable services such as video-on-demand, a cable operator's enhanced program guide and data-enhanced television services
may require the use of a set-top box. For more information call your local cable operator. This television also includes a QAM demodulator which should
allow you to receive unscrambled digital cable television programming via subscription service to a cable service provider.
Availability of digital cable television programming in your area depends on the type of programming and signal provided by your cable service provider.
Warning The CRT in this product employs a protective film on the face. This film must not be removed as it serves a safety function and removal will increase
the risk of serious injury. Note on Caption Vision This television receiver provides display of television closed captioning in accordance with §15.119 of the
FCC rules. Note on Cleaning the TV Clean the TV with a soft, dry cloth. Never use strong solvents such as thinner or benzine, which might damage the finish
of the cabinet. 1 IMPORTANT SAFEGUARDS For your protection, please read these instructions completely, and keep this manual for future reference.
Carefully observe and comply with all warnings, cautions and instructions placed on the set, or described in the operating instructions or service manual.
Object and Liquid Entry Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the set. WARNING To guard against injury, the following basic safety precautions should be observed in the installation, use,
and servicing of the set. Attachments Do not use attachments not recommended by the manufacturer, as they may cause hazards. Do not place any objects,
especially heavy objects, on top of the set. The object may fall from the set, causing injury. Use Power Sources This set should be operated only from the type
of power source indicated on the serial/model plate. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local
power company. For those sets designed to operate from battery power, refer to the operating instructions. Cleaning Unplug the set from the wall outlet
before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners.
Use a cloth lightly dampened with water for cleaning the exterior of the set. If a snapping or popping sound from a TV set is continuous or frequent while the
TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV sets to make occasional snapping or popping sounds,
particularly when being turned on or off. Grounding or Polarization This set is equipped with a polarized AC power cord plug (a plug having one blade wider
than the other), or with a three-wire grounding type plug (a plug having a third pin for grounding). Follow the instructions below: For the set with a
polarized AC power cord plug This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician
to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in. Installation Always use two or more people to lift or
move the set.
The set is heavy and the bottom surface is flat. Serious injury can result from trying to move the set by yourself alone, or from unsteady handling. Install the
set on a stable, level surface. Water and Moisture Do not use power-line operated sets near water -- for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool, etc. Alternate Warning For the set with a three-wire grounding type AC plug This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable
outlet installed. Do not defeat the safety purpose of the grounding plug. Accessories Do not place the set on an unstable cart, stand, tripod, bracket, table or
shelf. The set may fall, causing serious injury to a child or an adult, and serious damage to the set.
Use only a cart or stand recommended by the manufacturer for the specific model of TV. Any mounting of the product should follow the manufacturer's
instructions, and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Disconnect all cables and cords from the set before
attempting to move the set. Do not allow children or pets to climb up onto, or push against, the set. The set may fall, causing serious injury. Overloading Do
not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
Always turn the set off when it is not to be used. When the set is left unattended and unused for long periods of time, unplug it from the wall outlet as a
precaution against the possibility of an internal malfunction that could create a fire hazard.
Do not disconnect the antenna or the power cord during a heavy storm. Lightning may strike while you are holding the cable or cord, causing serious injury.
Turn off your TV and wait for the weather to improve. Memory Stick To protect small children from injury from Memory Stick Media, remove all Memory
Stick media from the TV's Memory Stick slot and store it in a safe location when it is not in use. 2 Ventilation The slots and openings in the cabinet and in the
back or bottom are provided for necessary ventilation.
To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered. Lightning For added
protection for this television receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna. This will prevent damage to the receiver due to lightning and power line surges. Never cover the slots and openings with a cloth
or other materials. Never block the slots and openings by placing the set on a bed, sofa, rug or other similar surface.
Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided. Do not place the set near or over a
radiator or heat register, or where it is exposed to direct sunlight. Service Damage Requiring Service Unplug the set from the wall outlet and refer servicing
to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the set or
objects have fallen into the product. If the set has been exposed to rain or water. If the set has been subject to excessive shock by being dropped, or the cabinet
has been damaged. If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the
operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore
the set to normal operation. When the set exhibits a distinct change in performance, it indicates a need for service.
Power Cord Protection Do not allow anything to rest on or roll over the power cord, and do not place the set where the power cord is subject to wear or
abuse. Antennas Outdoor Antenna Grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be
located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES
OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection
against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code
in Canada provide information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to a.....
.....
.....
.......19 Cable Box and Cable Only ...
..........
.....
.....
..........
..........
.....
.....
..........
20 Cable Box Only..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
21 Connecting Optional Equipment ..........
..........
.....
.....
..........
..........
.....
.....
...22 Making Video Connections.......
..........
.....
.....
..........
..........
.....
.....
.....23 About Using S VIDEO .....
..........
.....
.....
..........
..........
.....
.....
..........
.....23 VCR and Cable .....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.....24 VCR and Cable Box .....
..........
.....
.....
..........
..........
.....
.....
..........
........26 Two VCRs for Tape Editing ..
.....
.....
..........
..........
.....
.....
..........
..........
28 Satellite Receiver.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
........30 Satellite Receiver and VCR ..
..........
.....
.....
..........
..........
.....
.....
..........
.32 DVD Player with Component Video Connectors.........
.....
.....
..........
..34 DVD Player with S VIDEO and Audio Connectors ........
.....
.....
..........
.36 Camcorder .........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.......37 Audio Receiver ...
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
..38 DVI-Equipped Device ...
..........
..........
.....
.....
..........
..........
.....
.....
........39 HDMI-Equipped Device ..
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
........69 Memory Stick Compatibility ..
.....
.....
..........
..........
.....
.....
..........
.........70 Memory Stick Functionality .
.....
.....
..........
..........
.....
.....
..........
..........
.70 File Compatibility ....
.....
..........
..........
.....
.....
..........
..........
.....
.....
........71 Trademark Information ..
..........
.....
.....
..........
..........
.....
.....
..........
......71 Inserting and Removing a Memory Stick ....
.....
.....
..........
..........
.....
.....
......72 Inserting a Memory Stick ....
..........
.....
.....
..........
..........
.....
.....
..........
.72 Removing a Memory Stick .........
.....
.....
..........
..........
.....
.....
..........
....73 Using the Memory Stick Index ......
.....
.....
..........
..........
.....
.....
..........
..........
.74 Using the Memory Stick Index ....
.....
..........
..........
.....
.....
..........
........75 Viewing Photos ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.........76 Photo Controls .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.........76 Photo Menu Bar Options .
..........
.....
.....
..........
..........
.....
.....
..........
....77 Using Zoom and Pan ......
.....
.....
..........
..........
.....
.....
..........
..........
.....
78 Using Rotate.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.........78 Other Info SETUP 6 Playing Movies .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.79 Movie Controls....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.79 Movie Menu Bar Options .........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....80 Memory Stick Index Menu Bar Options .
..........
..........
.....
.....
..........
..........
.81 Slide Show Menu Options ....
.....
..........
..........
.....
.....
..........
..........
....81 Contents Menu Options .
.....
..........
..........
.....
.....
..........
..........
.....
.....
82 Memory Stick Menu ..........
..........
.....
.....
..........
..........
.....
.....
..........
..82 Notes on Using Memory Stick Media ........
.....
.....
..........
..........
.....
.....
........83 About DCF File Names ..
..........
.....
.....
..........
..........
.....
.....
..........
.......83 Memory Stick Precautions...
.....
.....
..........
..........
.....
.....
..........
..........
.84 Welcome SETUP Using i.LINK About i.LINK ..
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
....85 Using i.
LINK Cables..........
..........
.....
.....
..........
..........
.....
.....
..........
....85 Connecting i.LINK Devices .....
.....
.....
..........
..........
.....
.....
..........
........86 Selecting an i.LINK Device .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
...88 Using the i.LINK Control Panel ......
..........
.....
.....
..........
..........
.....
.....
..........
.89 Notes About Controlling i.LINK Devices ........
.....
.....
..........
..........
.....
90 i.LINK Setup ....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
...91 Notes on i.LINK......
..........
.....
.....
..........
..........
.....
.....
..........
..........
....91 SETUP Using the Menus Overview .
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.....93 Navigating Through Menus .....
..........
.....
.....
..........
..........
.....
.....
..........
......93 Using the Video Menu ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
......94 Using the Audio Menu ....
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
97 Using the Screen Menu .....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...99 Using the Channel Menu .......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.. 100 Using the Parent Menu...
..........
..........
.....
.....
..........
..........
.....
.....
..........
....102 Using the Setup Menu ......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
.. 105 Using the Applications Menu........
..........
.....
.....
..........
..........
.....
.....
......... 108 SETUP Other Information Overview .
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
........111 Glossary ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.... 112 Contacting Sony .
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.. 113 Troubleshooting...
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
113 Twin View .....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......... 113 Remote Control .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
......114 CableCARD ....
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.... 114 Channels .
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.115 Memory Stick ....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...... 116 Audio ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
........117 Video ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
118 General .....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......... 118 Specifications .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.120 Optional Accessories....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.. 121 Index ........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
... 123 SETUP Other Info 7 Introducing the FD Trinitron Wega Overview This chapter describes the contents of the package in which the TV is shipped and
provides an overview of the features of your Wega TV. Presenting the FD Trinitron Wega The FD Trinitron Wega (pronounced VAY-GAH) is characterized
by outstanding contrast, uncompromising accuracy, and corner-tocorner detail.
You will recognize the superiority of Wega technology almost immediately. The first thing you will probably notice is minimal glare from the flat picture tube.
This flat-screen technology improves picture detail without distortion, unlike conventional curved screens. The FD Trinitron delivers outstanding image detail
not only at the screen center, but also at the corners -- so you can enjoy a bright, clear picture from any location in a room. Package Contents Along with
your new Trinitron TV, the packing box contains a remote control and two AA (R6) batteries. These items are all you need to set up and use the TV. Features
Some of the features that you will enjoy with your new TV include: Built-in Digital Television Receiver: You can watch digital television programs and enjoy
the improved audio/video quality offered by these programs. With high-definition signal reception, you can watch TV signals broadcast in HDTV for the
clearest possible broadcast picture. 9 SETUP CableCARD slot: Provides cable subscribers with access to digitally encrypted cable channels -- without the
need for a settop box -- that will enable you to receive not only standard definition but also high definition television. The CableCARD, which is provided by
your cable TV company, is inserted into the TV's rear panel CableCARD slot.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
After the service is activated with your cable TV company, the card replaces the need for a separate set-top box. (Check with your cable TV company about
CableCARD service details, limitations, pricing, and availability. For more information about CableCARD in this manual, see pages 17 and 43.) Wide Screen
Mode: Watch conventional 4:3 aspect ratio broadcasts in wide screen (16:9) mode. Super Fine Pitch CRT: Created especially for displaying high resolution
pictures, the new Super Fine Pitch CRT -- along with a new electron gun and high intensity luminescent phosphor -- improves image resolution, providing the
highest picture quality reproduction from corner to corner. DRC® (Digital Reality Creation) Multifunction V1: Unlike conventional line doublers, the DRC
Multifunction feature replaces the signal's NTSC waveform with the near-HD equivalent, while doubling the number of vertical and horizontal lines. This
results in four times the density for quality sources, such as DVD, satellite, and digital camcorders. The Video Menu allows you to select interlaced,
progressive, or CineMotionTM output. The DRC Palette option lets you customize the level of detail (Reality) and smoothness (Clarity) to create up to three
custom palettes. Scrolling Index: Lets you select programs from a series of preview windows that scroll along the right side of the screen.
Twin ViewTM: Using the Multi-Image Driver (MIDX), Twin View allows you to watch two programs side by side, with the ability to zoom in one picture. You
can watch pictures from two different sources (1080i, 720p, 480p, and 480i) simultaneously. (Only the left Twin View window can display 1080i, 720p, and
480p sources.) Favorite Channels: Allows you to preview and select from 16 of your favorite channels. ClearEdge VMTM Velocity Modulation: Sharpens
picture definition by enhancing vertical lines.
Welcome SETUP SETUP SETUP SETUP Memory Stick® Viewer: Lets you watch digital photo (JPEG) and movie (MPEG1) files that are stored on Memory
Stick media. 10 Introducing Steady Sound®: Equalizes volume levels so there is consistent output between programs and commercials. Component Video
Inputs: Offers the best video quality for DVD (480p, 480i), and digital set-top box (HD1080i, 720p) connections. Welcome HD DetailerTM: Wideband video
amplifier has a high bandwidth frequency rating, which allows it to send more video information to the screen, resulting in finer picture quality, especially for
HD sources. CineMotionTM: Reverse 3-2 pulldown processing provides optimal picture quality for film-based sources (media originally shot in 24 framesper-second format).
Parental Control: V-Chip technology allows parents to block unsuitable programming from younger viewers. HDMI (High-Definition Multimedia Interface):
Provides an uncompressed, all-digital audio/video interface between this TV and any HDMI-equipped audio/video component, such as a settop box, DVD
player, and A/V receiver. HDMI supports enhanced, or high-definition video, plus two-channel digital audio. i.LINK: Provides a secure digital interface to
other digital home entertainment devices. i.LINK allows for the secure transfer of copyright-protected high-definition content between these devices and your
digital television. SETUP SETUP SETUP SETUP SETUP 11 Setting Up the TV Overview This chapter includes illustrated instructions for setting up your TV.
Topic Page(s) TV Controls and Connectors Basic Connections: Connecting a Cable or Antenna Connecting Optional Equipment VCR and Cable VCR and
Cable Box Two VCRs for Tape Editing Satellite Receiver Satellite Receiver and VCR DVD Player with Component Video Connectors DVD Player with S
VIDEO and Audio Connectors Camcorder Audio Receiver DVI-Equipped Device HDMI-Equipped Device Connecting a Device with an Optical IN Connector
Using the CONTROL S Feature Using CableCARD Setting Up the Channel List 14-16 17-21 24 26 28 30 32 34 36 37 38 39 40 41 42 43 45 About the AC
Power Cord The AC power cord is attached to the rear of the TV with a hook. Use caution when removing the AC plug from its holder.
Gently slide the plug upward to remove it from the hook. Once removed, the AC power plug should automatically disengage from its stored location. Do not
plug in the AC power cord until you have made all other connections. You can detach the cord from this hook AC power cord 13 TV Controls and Connectors
SETUP Front Panel 1 2 3 45 6 7 8 9 q; qa qs STD/DUO qd qf i.LINK STAND BY qg qh TIMER/ STAND BY qj VIDEO 2 INPUT I.LINK S VIDEO VIDEO
L(MONO) - AUDIO R i.LINK + VOLUME CHANNEL _ PRO POWER TV/VIDEO MENU Setup Item Description 1 i.LINK Connects to the i.LINK jack on
your i.LINK-compatible portable device.
Provides a secure digital connection between your TV and your i.LINKcompatible portable device, such as a digital video camcorder. Connects to the S
VIDEO OUT jack on your camcorder or other video equipment that has S VIDEO. Provides better picture quality than composite video (3). Connects to the
composite A/V output jacks on your camcorder or other video equipment.
Press to display the Menu. Press again to exit from the Menu. For details, see "Using the Menus" on page 93. Press to display the i.LINK Control Panel.
For details, see page 89. Press Vv B b to move the TV's on-screen cursor. Press to select an item in the TV's Menu. Press to display the Memory Stick Menu.
For details, see "Using the Memory Stick Viewer" on page 69. Press repeatedly to cycle through the video equipment connected to the TV's video inputs. Press
to adjust the volume. Press to scan through channels. To scan quickly through channels, press and hold down either CHANNEL button. Memory Stick
insertion slot.
For details, see "Inserting and Removing a Memory Stick" on page 72. When lit, indicates that the Memory Stick is being read. (Do not remove the Memory
Stick when the indicator is lit.) When lit in orange, indicates that i.LINK Standby is on. For details, see page 106. Blinks when the TV is turned on, then shuts
off when the picture is displayed. If the LED blinks continuously, this may indicate the TV needs service (see "Contacting Sony" on page 113). When lit,
indicates one of the timers is set. When the timer is set, this LED will remain lit even if the TV is turned off.
For details, see page 108. Receives IR signals from the TV's remote control. Press to turn on and off the TV. 2 S VIDEO VIDEO 2 INPUT 3
VIDEO/L(MONO)-AUDIO-R VIDEO 2 INPUT 4 MENU 5 i.LINK 6 Vv B b 7 SETUP SETUP SETUP SETUP 8 9 TV/VIDEO 0 -VOLUME + qa -CHANNEL+
qs PRO STD/DUO qd Memory Stick LED qf i.
LINK STAND BY LED qg TIMER/STAND BY LED qh Infrared Receiver (IR) qj POWER 14 SETUP Setup SETUP SETUP SETUP SETUP qs qa 9 q; 2 1 3 4 5
Rear Panel 6 7 8 15 Jack Description 1 VHF/UHF RF input that connects to your VHF/UHF antenna or cable box.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
Connects to the S VIDEO OUT jack of your VCR or other video equipment that has S VIDEO. S VIDEO provides better picture quality than either composite
video (3) or VHF/UHF (1) connections. Connect to the composite A/V output jacks on your VCR or other video component. A fourth component A/V input
jack (VIDEO 2) is located on the front panel of the TV.
This video connection provides better picture quality than the VHF/UHF (1) connection. Lets you record the program you are watching to a VCR. When two
VCRs are connected, you can use the TV as a monitor for tape-to-tape editing (not available with digital channels or with 480i, 480p, 720p, or 1080i when the
input is set to VIDEO 5, 6, or 7). Connects to the left and right audio input jacks of your audio or video equipment. You can use these outputs to listen to your
TV's audio through your stereo system. SETUP Setup 2 S VIDEO IN 1/3 3 VIDEO IN 1/3/4 VIDEO/L(MONO) -AUDIO-R 4 MONITOR OUT 5 AUDIO OUT
(VAR/FIX) 6 HD/DVD IN 5/6 Connect to your DVD player's or digital set-top box's component video (Y, PB, PR) (1080i/720p/480p/480i) and audio (L/R)
jacks. Component video provides better picture quality than 1, 2, or 3). SETUP 7 CONTROL S IN/OUT 8 HDMI (VIDEO 7 IN) Allows the TV to receive (IN)
and send (OUT) remote control signals to other Sony infrared-controlled audio or video equipment that has the CONTROL S function. HDMI (HighDefinition Multimedia Interface) provides an uncompressed, alldigital audio/video interface between this TV and any HDMI-equipped audio/video
component, such as a set-top box, DVD player, and A/V receiver. HDMI supports enhanced, or high-definition video, plus two-channel digital audio.
SETUP 9 DIGITAL AUDIO OPTICAL Connect to the optical audio input of an audio component that is Dolby* Digital and OUTPUT PCM compatible.
(DOLBY DIGITAL PCM) 0 CableCARD Slot Provides cable subscribers with access to digitally encrypted cable channels -- without the need for a set-top
box -- that will enable you to receive not only standard definition but also high definition television. The CableCARD, which is provided by your cable TV
company, is inserted into this slot. After the service is activated with your cable TV company, the card replaces the need for a separate settop box. Check with
your cable TV company about CableCARD service details, limitations, pricing, and availability. For more information, see page 43. Connects to the i.LINK
jack on your i.LINK-compatible device. Provides a secure digital connection between your TV and your i.
LINK-compatible device. RF input that connects to your cable signal. SETUP SETUP qa i.LINK (2 inputs) qs Cable * Dolby and the double-D symbol are
trademarks of Dolby Laboratories Licensing Corporation. 16 Basic Connections: Connecting a Cable or Antenna The way in which you will connect your TV
varies, depending on how your home receives a signal (cable, cable box, antenna) and whether or not you plan to connect a VCR.
If You Are Connecting Cable or Antenna Only See Page SETUP 18 19 20 No cable box or VCR No cable box or VCR Cable and Antenna Only Cable Box and
Cable Only Setup Cable box unscrambles only some channels (usually premium channels) No VCR 21 Cable box unscrambles all channels No VCR Cable
Box Only If you are connecting a VCR See the connections described on pages 24 and 26. SETUP About Using CableCARD If you are planning to use a
separate cable box for digital cable TV services, you may be able to receive programming using this TV with the CableCARD instead -- except in the
following circumstances: SETUP Your cable TV company does not provide CableCARD service in your viewing area. You want to access your cable TV
company's interactive or advanced features (such as video-on-demand or, in some cases, pay-per-view). At this time, these services require a bidirectional
link, which are only available through the use of a separate set-top box. CableCARD is currently a unidirectional device only, and cannot provide these
advanced services.
Check with your cable TV company for CableCARD service details, limitations, pricing, and availability, all of which are determined by your cable TV
company -- not Sony. For information on installing and activating CableCARD, see "Using CableCARD" on page 43. SETUP SETUP 17 SETUP Cable or
Antenna Only For best results, use one of the following connections if you are connecting a cable or an antenna and you: Do not need a cable box to
unscramble channels. (If you have a cable box, see pages 20-21.) Do not intend to connect a VCR. (If you have a VCR, see pages 24 and 26.) The connection
you choose depends on the cable type you have in your home, as described below. Setup 75-ohm coaxial cable (usually found in newer homes) Cable Type
Connect As Shown 75-ohm coaxial cable TV VHF/UHF TV CABLE VHF Only or combined VHF/UHF Cable SETUP 75-ohm coaxial cable 300-ohm twin
lead cable (usually found in older homes) Cable Type Connect As Shown 300-ohm twin lead cable TV VHF/UHF Antenna connector (not supplied) SETUP
VHF Only or UHF Only or combined VHF/UHF SETUP 75-ohm coaxial and 300-ohm twin lead cable (found in some homes) Cable Type Connect As Shown
75-ohm coaxial cable TV VHF/UHF U/V mixer (not supplied) 300-ohm twin lead cable VHF and UHF SETUP 18 Cable and Antenna Only For best results,
use this connection if you: Have a cable and an antenna. SETUP (This is convenient if you are using a separate rooftop antenna to receive additional
channels that are not provided by your cable TV company.) Do not have a cable box or VCR.
(If you have a cable box, see pages 20 to 21. If you have a VCR, see pages 24 and 26.) Connect As Shown Cable Type Cable TV (CATV) and Antenna Setup
Antenna cable CATV cable Notes on Using This Connection SETUP To Do This ... Do This ... Switch the TV's input between the cable and antenna Press ANT
to switch back and forth between the TV's VHF/UHF and CABLE inputs. SETUP SETUP SETUP 19 SETUP Cable Box and Cable Only Before connecting a
cable box, see "About Using CableCARD" on page 17.
For best results, use this connection if: Your cable TV company scrambles some channels, such as premium channels (which requires you to use a cable box),
but does not scramble all channels. You do not have a VCR. (If you have a VCR, see pages 24 and 26.) With this connection you can: Use the TV remote
control to change channels coming through Setup the cable box to the TV's VHF/UHF input jack. (You must first program the remote control for your specific
cable box; see "Programming the Remote Control" on page 51.
) Use the TV remote control to change channels coming directly into the TV's CABLE input. (The TV's tuner provides a better signal than the cable box.)
Splitter Coaxial cable SETUP CATV cable Coaxial cable Cable box Coaxial cable TV SETUP VHF/UHF CABLE About Using This Connection with Dual
Picture (Twin View, etc.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
) Features With this connection, you can use all the dual picture features for unscrambled channels coming directly into the TV's CABLE input jack. Notes on
Using This Connection SETUP To Do This .
.. Do This ... Use the cable box Set up the TV remote control to operate the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or
4) and then use the cable box to switch channels. Program the remote control. See "Programming the Remote Control" on pages 51-52. Activate the remote
control to Press SAT/CABLE FUNCTION. operate the cable box SETUP Switch the TV's input between the cable box and cable Press ANT to switch back and
forth between the TV's VHF/UHF (scrambled channels) and CABLE (unscrambled) inputs.
20 Cable Box Only Before connecting a cable box, see "About Using CableCARD" on page 17. For best results, use this connection if: Your cable TV
company scrambles all channels, which requires SETUP you to use a cable box. You do not have a VCR. (If you have a VCR, see pages 24 and 26.) With this
connection you can: Use the TV remote control to change channels coming through the cable box to the TV's VHF/UHF jack. (You must first program the
remote control for your specific cable box.) Setup About Using This Connection with Dual Picture (Twin View, etc.) Features With this connection, all
channels come into the TV through your cable box and only one unscrambled signal is sent to the TV, so you cannot use the dual picture features.. If some of
your channels are scrambled, but others are not, consider using the "Cable Box and Cable" connection on page 20 instead.
To connect the cable box 1 Connect the CATV cable to the cable box's input jack. 2 Use a coaxial cable to connect the cable box's output jack to the TV's
VHF/UHF jack. CATV cable Coaxial cable VHF/UHF TV SETUP 1 IN Cable box 2 OUT SETUP 3 Run Auto Program, as described in "Setting Up the
Channel List" on page 45. Notes on Using This Connection To Do This ..
. Do This ... Use the cable box Set up the TV remote control to operate the cable box Tune the TV to the channel the cable box is set to (usually channel 3 or 4)
and then use the cable box to switch channels.
Program the remote control. See "Programming the Remote Control" on pages 51. SETUP Activate the remote control to Press SAT/CABLE FUNCTION.
operate the cable box SETUP 21 Connecting Optional Equipment SETUP Use the directions in this section to connect the following optional equipment: If
You Are Connecting See Page VCR and Cable VCR and Cable Box Two VCRs for Tape Editing Satellite Receiver Satellite Receiver and VCR DVD Player
with Component Video Connectors DVD Player with S VIDEO and Audio Connectors Camcorder Audio Receiver DVI-Equipped Device 24 26 28 30 32 34 36
37 38 39 40 SETUP Setup HDMI-Equipped Device SETUP SETUP SETUP 22 Making Video Connections Your TV includes several types of video inputs.
When connecting your TV, use the inputs that are available on your components that provide the best video performance, as described below. Best Video
Performance SETUP HDMI (High-Definition Multimedia Interface) Component video Setup S VIDEO Composite video RF/Coaxial Good Video Performance
SETUP About Using S VIDEO If the optional equipment you are connecting has an S VIDEO jack (shown at left), you can use an S VIDEO cable for
improved picture quality (compared to an A/V cable). Because S VIDEO carries only the video signal, you also need to connect audio cables for sound, as
shown below. SETUP Example of an S VIDEO Connection TV S VIDEO cable SETUP Equipment with S VIDEO Cables are often color-coded to connectors.
Connect red to red, white to white, etc. SETUP Audio cable 23 VCR and Cable SETUP For best results, use this connection if: Your cable TV company does
not require you to use a cable box.
About Using This Connection with Dual Picture (Twin View, etc.) Features With this connection, you can use all the dual picture features. To connect the
VCR and cable Using S VIDEO jacks? See page 23. 1 Connect the CATV cable to the VCR's VHF/UHF input jack. 2 Use a coaxial cable to connect the VCR's
VHF/UHF output jack to the TV's CABLE jack. Setup 3 Use an A/V cable to connect the VCR's A/V output jacks to the TV's A/V input jacks. 4 Run Auto
Program, as described in "Setting Up the Channel List" on page 45. TV SETUP Coaxial cable VCR SETUP CATV cable A/V cable Cables are often colorcoded to connectors. Connect red to red, white to white, etc. SETUP SETUP 24 Notes on Using This Connection To Do This .
.. Do This ...
Watch the VCR Watch cable channels Set up the TV remote control to operate the VCR Activate the TV remote control to operate the VCR Control VCR
functions with the TV remote control Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the illustration). Press TV/VIDEO repeatedly to select
the cable input (CABLE in the illustration). If you have a non-Sony VCR, you must program the remote control. See "Programming the Remote Control" on
pages 51-52. Open the outside cover, as shown on page 50.
@@See "Operating a VCR" on page 66. SETUP Setup See the instructions for setting up Video Labels on page 105. Label video inputs to easily identify
equipment connected to the TV SETUP SETUP SETUP SETUP 25 VCR and Cable Box SETUP For best results, use this connection if: Your cable TV
company scrambles some channels, such as Before connecting a cable box, see "About Using CableCARD" on page 17. premium channels (which requires
you to use a cable box), but does not scramble all channels. About Using This Connection with Dual Picture (Twin View, etc.) Features With this connection,
you can use all the dual picture features. With this connection you can: Use the TV remote control to change channels coming through Setup the cable box.
(You must first program the remote control for your specific cable box; see "Programming the Remote Control" on page 51.) Use the TV remote control to
change channels coming directly into the TV's CABLE jack. (The TV's tuner provides a better signal than the cable box.
) Record channels coming through the cable box and channels coming directly into the TV. SETUP To connect a VCR and cable box, you need: A splitter,
which is a small, inexpensive device that you can purchase at your local electronics store. Four coaxial cables. Two A/V cables or two S VIDEO cable with
audio cables. SETUP To connect the VCR and cable box 1 Connect the CATV cable to the single (input) jack of the splitter. 2 Use a coaxial cable to connect
one of the splitter's two output jacks to the TV's CABLE jack.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
3 Use a coaxial cable to connect the splitter's other output jack to the cable box's input jack. SETUP 4 Use a coaxial cable to connect the cable box's output
jack to the VCR's RF input jack. 5 Use an A/V cable to connect the cable box's A/V output jacks to Using S VIDEO jacks? See page 23. the TV's A/V input
jacks.
6 Use an A/V cable to connect the VCR's A/V output jacks to the TV's A/V input jacks. 7 Run Auto Program, as described in "Setting Up the Channel List" on
page 45. SETUP 26 TV Coaxial cable Splitter (not supplied) CATV cable Coaxial cable Cable box Cables are often color-coded to connectors. Connect red to
red, white to white, etc. Coaxial cable SETUP Setup A/V cable SETUP VCR A/V cable SETUP Notes on Using This Connection To Do This .
.. Do This ...
Watch cable (unscrambled) channels Watch cable box (scrambled) channels Watch the VCR Set up the TV remote control to operate the cable box or VCR
Press TV/VIDEO repeatedly to select the cable input (CABLE in the illustration). Press TV/VIDEO repeatedly to select the cable box input (VIDEO 3 in the
illustration). Use the cable box to change channels. Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the illustration). If you have a non-Sony
VCR, you must program the remote control. See "Programming the Remote Control" on pages 51-52. SETUP SETUP Activate the remote control to For the
cable box, press SAT/CABLE FUNCTION. For the VCR, open the outside operate the cable box or VCR cover, as shown on page 50. @@Control specific
cable box and See "Operating a Cable Box" on page 67 and "Operating a VCR" on page 66. VCR functions with the TV remote control See the instructions
for setting up Video Labels on page 101.
Label video inputs to easily identify equipment connected to the TV 27 SETUP Two VCRs for Tape Editing Using S VIDEO jacks? See page 23. Connecting
two VCRs lets you record from one VCR to the other. By connecting them as shown below, you can view (monitor) what is being recorded. To connect two
VCRs for tape editing 1 Use an A/V cable to connect the playback VCR's A/V output jacks to the TV's A/V input jacks. 2 Use an A/V cable to connect the
recording VCR's A/V input jacks to the TV's MONITOR OUT jacks. Setup TV Cables are often color-coded to connectors. Connect red to red, white to white,
etc. SETUP Playback VCR Recording VCR SETUP A/V cable A/V cable SETUP SETUP 28 Notes on Using This Connection To Do This ...
Do This ... View (monitor) what is being recorded Set up the TV remote control to operate the VCR(s) Activate the TV remote control to operate the VCR(s)
Control VCR functions with the TV remote control Press TV/VIDEO repeatedly to select the VCR input (VIDEO 1 in the illustration above). If you have a nonSony VCR, you must program the remote control.
See "Programming the Remote Control" on pages 51-52. Open the outside cover, as shown on page 50. @@See "Operating a VCR" on page 66. SETUP See
the instructions for setting up Video Labels on page 105. Label video inputs to easily identify equipment connected to the TV Setup SETUP SETUP SETUP
SETUP 29 Satellite Receiver To connect a satellite receiver SETUP 1 Connect the satellite antenna cable to the satellite receiver's Using S VIDEO jacks? See
page 23.
satellite input jack. 2 Use an A/V cable to connect the satellite receiver's A/V output jacks to the TV's A/V input jacks. 3 Connect a CATV cable from your
cable or antenna to the TV's CABLE jack. 4 Run Auto Program, as described in "Setting Up the Channel List" Setup on page 45. TV CATV cable Satellite
receiver SETUP Satellite antenna cable A/V cable Cables are often color-coded to connectors. Connect red to red, white to white, etc. SETUP SETUP SETUP
30 Notes on Using This Connection To Do This ... Do This .
.. Watch the satellite receiver Set up the TV remote control to operate the satellite receiver Activate the TV remote control to operate the satellite receiver
Press TV/VIDEO repeatedly to select the satellite receiver input (VIDEO 1 in the illustration). If you have a non-Sony satellite receiver, you must program the
remote control. See "Programming the Remote Control" on pages 51-52. Press SAT/CABLE FUNCTION. SETUP Control satellite receiver functions with the
See "Operating a Satellite Receiver" on page 66. TV remote control Label video inputs to easily identify equipment connected to the TV See the instructions
for setting up Video Labels on page 105. Setup SETUP SETUP SETUP SETUP 31 SETUP Satellite Receiver and VCR To connect a satellite receiver and VCR
1 Connect the CATV cable to the single (input) jack of the splitter. 2 Use a coaxial cable to connect one of the splitter's two output jacks to the TV's CABLE
jack.
3 Use a coaxial cable to connect the splitter's other output jack to Using S VIDEO jacks? See page 23. the satellite receiver's VHF/UHF input jack. 4 Connect
the satellite antenna cable to the satellite receiver's satellite input jack. Setup 5 Use a coaxial cable to connect the satellite receiver's VHF/UHF output jack to
the VCR's VHF/UHF input jack. 6 Use an A/V cable to connect the satellite receiver's A/V output jacks to the TV's A/V input jacks.
7 Use an A/V cable to connect the VCR's A/V output jacks to the TV's A/V input jacks. 8 Run Auto Program, as described in "Setting Up the Channel List"
SETUP on page 45. CATV cable Splitter (not supplied) Satellite antenna cable Coaxial cable TV Coaxial cable Satellite receiver SETUP Cables are often
color-coded to connectors. Connect red to red, white to white, etc. Coaxial cable A/V cable SETUP SETUP VCR A/V cable 7 32 Notes on Using This
Connection To Do This .
.. Do This ... Watch the satellite receiver Watch the VCR Set up the TV remote control to operate the satellite receiver or VCR Press TV/VIDEO repeatedly to
select the VCR input (VIDEO 3 in the illustration). Press TV/VIDEO repeatedly to select the input to which the VCR is connected (VIDEO 1 in the
illustration). If you have a non-Sony VCR or satellite receiver, you must program the remote control. See "Programming the Remote Control" on pages 51-52.
SETUP For the satellite receiver, press SAT/CABLE FUNCTION.
For the VCR, open the Activate the TV remote control to operate the satellite outside cover, as shown on page 50. @@receiver or VCR Control satellite
receiver and VCR functions with the TV remote control See "Operating a Satellite Receiver" on page 66 and "Operating a VCR" on page 66. Setup See the
instructions for setting up Video Labels on page 105. Label video inputs to easily identify equipment connected to the TV SETUP SETUP SETUP SETUP 33
SETUP DVD Player with Component Video Connectors For best results, use this connection if your DVD player has component video (Y, PB, PR) jacks.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
To connect a DVD player with component video connectors 1 Use three separate component video cables to connect the DVD player's Y, PB and PR jacks to
the Y, PB and PR jacks (VIDEO 5) on the TV. The Y, PB and PR jacks on your DVD player are sometimes labeled Y, CB and CR, or Y, B-Y and R-Y. If so,
connect the cables to like colors. Setup 2 Use an audio cable to connect the DVD player's audio output jacks to the TV's VIDEO 5 audio input jacks.
Component video cables SETUP TV DVD player SETUP Cables are often color-coded to connectors. Connect red to red, white to white, etc.
Audio cable SETUP SETUP 34 Notes on Using This Connection To Do This ... Do This ..
. Watch the DVD player Set up the TV remote control to operate the DVD player Activate the TV remote control to operate the DVD player Control DVD
functions with the TV remote control Press TV/VIDEO repeatedly to select the DVD input (VIDEO 5 in the illustration). If you have a non-Sony DVD player,
you must program the remote control. See "Programming the Remote Control" on pages 51-52. Open the outside cover, as shown on page 50.
@@See "Operating a DVD Player" on page 67. SETUP Setup See the instructions for setting up Video Labels on page 105. Label video inputs to easily
identify equipment connected to the TV You cannot record the signal from any equipment connected into the Y, PB, PR jacks. SETUP SETUP SETUP SETUP
35 SETUP DVD Player with S VIDEO and Audio Connectors Use this connection if your DVD player does not have component video (Y, PB, PR) jacks. To
connect a DVD player with A/V connectors 1 Use an audio cable to connect the DVD player's audio output jacks to the TV's audio input jacks. 2 Use an S
VIDEO cable to connect the DVD player's S VIDEO jack to the TV's S VIDEO jack. Setup TV DVD player S VIDEO cable SETUP Cables are often colorcoded to connectors. Connect red to red, white to white, etc. Audio cable SETUP Notes on Using This Connection To Do This ..
. Do This ... Watch the DVD player Set up the TV remote control to operate the DVD player Activate the TV remote control to operate the DVD player
Control DVD functions with the TV remote control Press TV/VIDEO repeatedly to select the DVD input (VIDEO 1 in the illustration). If you have a non-Sony
DVD player, you must program the remote control. See "Programming the Remote Control" on pages 51-52. Open the outside cover, as shown on page 50.
@@See "Operating a DVD Player" on page 67. SETUP SETUP See the instructions for setting up Video Labels on page 105.
Label video inputs to easily identify equipment connected to the TV 36 Camcorder For easy connection of a camcorder, the TV has front A/V input jacks. If
you prefer, however, you can connect the camcorder to the TV's rear A/V input jacks. SETUP If your camcorder is equipped with an i.LINK jack, you can
connect it using Using S VIDEO jacks? See page 23. i.
LINK instead of the A/V inputs. See "Using i.LINK" on page 85. To connect a camcorder 1 Use A/V cables to connect the camcorder's A/V output jacks to the
TV's A/V input jacks. TV Setup VIDEO 2 INPUT I.
LINK S VIDEO VIDEO L(MONO) - AUDIO R SETUP Cables are often color-coded to connectors. Connect red to red, white to white, etc. A/V cable SETUP
Camcorder To A/V output If you have a mono camcorder, connect its audio output jack to the TV's L MONO audio jack. Notes on Using This Connection To
Do This ... Do This ... SETUP Watch the camcorder Press TV/VIDEO repeatedly to select the camcorder input (VIDEO 2 in the illustration).
See the instructions for setting up Video Labels on page 105. Label video inputs to easily identify equipment connected to the TV SETUP 37 Audio Receiver
SETUP For improved sound quality, you may want to play the TV's audio through your stereo system. To connect an audio system 1 Use an audio cable to
connect the TV's audio output jacks to the audio receiver's line input jacks. TV SETUP Setup Cables are often color-coded to connectors. Connect red to red,
white to white. Audio cable To line input SETUP Receiver 2 Using the TV's Audio Menu, set the Speaker option to Off. Then set the Audio Out option to Fixed
or Variable, depending on how you want to control the volume. For details, see "Using the Audio Menu" on page 97. SETUP 3 Turn on the audio receiver,
and then set the receiver's line input to the jack into which you connected the TV. SETUP 38 DVI-Equipped Device If you have a device, such as an HDTV
receiver, that has DVI (Digital Video Interface) output, use the following connection.
To connect a device that has DVI OUT: SETUP 1 Use an HDMI-to-DVI cable to connect the device's DVI OUT jack to the TV's HDMI IN jack. You can
purchase HDMI cables (or cable adapters) at your local electronics store. Setup 2 Use an audio cable to connect the device's audio output jacks to the TV's
HDMI analog audio input jacks. TV SETUP HDMI-to-DVI cable Audio cable SETUP HDTV Receiver Note on Using This Connection To Do This ..
. Do This ... SETUP Watch the DVI device Press TV/VIDEO repeatedly to select the VIDEO 7 input.
See the instructions for setting up Video Labels on page 105. Label video inputs to easily identify equipment connected to the TV SETUP 39 SETUP HDMIEquipped Device If you have a device, such as an HDTV receiver, that has a HighDefinition Multimedia Interface (HDMI), use the following connection. To
connect a device that has HDMI OUT: 1 Use the HDMI cable that came with your device to connect the device's HDMI OUT jack to the TV's HDMI IN jack.
HDMI cables transmit both audio and video signals. (Separate audio cables Setup are not necessary.) You can purchase HDMI cables at your local
electronics store. TV SETUP HDMI cable SETUP HDTV Receiver Note on Using This Connection SETUP To Do This ... Do This .
.. Watch the HDMI device Press TV/VIDEO repeatedly to select the VIDEO 7 input. See the instructions for setting up Video Labels on page 105. Label video
inputs to easily identify equipment connected to the TV SETUP 40 Connecting a Device with an Optical IN Connector You can use the TV's DIGITAL AUDIO
OPTICAL output jack to connect an audio device that is Dolby Digital and PCM compatible, such as an audio amplifier. SETUP Using an optical cable,
connect the TV's DIGITAL AUDIO OPTICAL output jack to the device's audio optical input jack. TV Setup SETUP Optical audio cable Audio Amplifier
SETUP Because all equipment does not output digital audio, you should also connect the TV's analog audio output jacks to the amplifier's analog audio input
jacks, as described on page 38.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
SETUP SETUP 41 Using the CONTROL S Feature CONTROL S allows you to control your system and other Sony equipment with one remote control. In
addition to allowing you to control multiple devices with one remote control, the CONTROL S feature allows you to always point your remote control at your
TV, instead of having to point it at the other equipment, which might be hidden or out of direct line of sight. Use CONTROL S IN to send signals to the TV.
Use CONTROL S OUT to send signals to connected equipment. SETUP SETUP SETUP SETUP Setup SETUP 42 Using CableCARD CableCARD provides
cable subscribers with access to digitally encrypted cable channels -- without the need for a set-top box -- that will enable you to receive not only standard
definition but also high definition television. The CableCARD, which is provided by your cable TV company, is inserted into the TV's rear panel CableCARD
slot. After the service is activated with your cable TV company, the card replaces the need for a separate set-top box. SETUP About Using CableCARD Setup
If you are planning to use a separate cable box for digital cable TV services, you may be able to receive programming using this TV with the CableCARD
instead -- except in the following circumstances: Your cable TV company does not provide CableCARD service in your viewing area.
You want to access your cable TV company's interactive or advanced features (such as video-on-demand or, in some cases, pay-per-view). At this time, these
services require a bidirectional link, which are only available through the use of a separate set-top box. CableCARD is currently a unidirectional device only,
and cannot provide these advanced services. SETUP Check with your cable TV company for CableCARD service details, limitations, pricing, and availability,
all of which are determined by your cable TV company -- not Sony. Activating CableCARD Service Before you can use CableCARD service, you need to insert
the CableCARD (supplied by your cable TV company) and activate the service, as described below: SETUP 1 Turn off the TV.
2 Insert the CableCARD into the TV's CableCARD slot. SETUP Top of CableCARD is on same side as indicator on slot SETUP ! CAUTION: Inserting the
CableCARD incorrectly may result in permanent damage to the card and the TV. 43 z You can also access information about your CableCARD in the
Applications Menu (see page 109). 3 Gently push the card into the slot until it locks into place. 4 Turn on the TV. After 1-2 minutes, the CableCARD setup
screen is displayed. This screen includes information your cable TV company will request before they can activate your service. SETUP 5 Follow the
displayed instructions: Phone your cable TV company. A representative will guide you through the activation process. 6 After your CableCARD is activated,
your cable TV company will download the service information, including the channel list, to the CableCARD.
Setup After the CableCARD has acquired channels from your cable TV company, the TV tunes to the lowest available channel. Removing the CableCARD In
the event you want to cancel your service, contact your cable TV company. SETUP Once the CableCARD is removed, your TV will no longer decrypt digital
cable TV programming services that require CableCARD. 1 Turn off the TV. 2 Push the eject button on the TV's CableCARD slot to release the card. SETUP
Eject button SETUP 3 Pull the CableCARD straight out of the slot to remove it. To install a different CableCARD, follow the instructions in "Activating
CableCARD Service" on page 43. SETUP 44 Setting Up the Channel List After you finish connecting the TV, you need to run the Initial Setup feature, which
automatically creates a list of available analog and digital channels and lets you correct tilt and vertical correction settings. The Initial Setup screens appear
when you turn on your TV for the first time after hooking it up. SETUP Using Initial Setup To run Initial Setup 1 Press POWER to turn on the TV.
The Initial Setup screen appears. Setup 2 Using the joystick on the remote control, move the highlight to the desired language, then press The Tilt Correction
screen appears. z For more details on using Tilt Correction and Vertical Correction, see pages 105106. to select that language. 3 Move the joystick B b to
correct any tilt of the picture.
You can choose a correction between +7 and -7. SETUP When finished, press . The Vertical Correction screen appears. 4 Move the joystick V v to make a
vertical correction to the picture. You can choose a correction between +5 and -5.
When finished, press . z To exit the Tilt Correction and Vertical Correction screens, press the MENU button. z If you are using a CableCARD, Auto Program
is disabled for the CABLE input. 5 The next screen instructs you to connect your cable/antenna. Check that you've connected your signal source correctly. To
start Auto Program, move the joystick to highlight Yes and then press . Auto Program automatically creates a list of receivable analog and digital channels.
Auto Program may take 50 minutes or more to complete. A progress bar is displayed while the channel list is being created. When the channel list is
completed, the lowest numbered channel is displayed.
To run Auto Program at a later time Use the Auto Program feature as described on page 100. To add individual digital channels SETUP SETUP Use the
Digital Channel feature as described on page 100. To reset the TV to factory settings 1 Press POWER to turn on the TV. 2 Hold down RESET on the remote
control. 3 Press TV POWER on the TV. (The TV will turn itself off, then back on.) SETUP 4 Release RESET. 45 Using the Remote Control Overview This
chapter describes how to set up, program, and use the TV's remote control. Topic Page Inserting Batteries Button Descriptions Outside Panel Inside Panel
Programming the Remote Control 47 48 50 51 Inserting Batteries 1 Remove the battery cover from the remote control. 2 Insert two size AA (R6) batteries
(supplied) by matching the e and E terminals on the batteries to the diagram inside the battery compartment.
3 Replace the battery cover. 1 2 Remove the batteries to avoid damage from possible battery leakage Handle the remote control with care. whenever you
anticipate that the remote control will not be used for an extended period. Avoid dropping it, getting it wet, placing it in direct sunlight, near a heater, or
where the humidity is high. 47 Button Descriptions SETUP Outside Panel Button Description 1 MUTING MUTING SLEEP SAT/CABLE POWER 1 2 3 qh
Press to mute the sound.
Press again or press VOL+ to restore the sound. Press repeatedly until the TV displays the time in minutes (15, 30, 45, 60, or 90) that you want the TV to
remain on before shutting off automatically.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
To cancel press until Sleep Off appears. While the Sleep feature is set, press once to display the remaining time. Also available in the Applications Menu
(page 108).
Press to display the i.LINK Control Panel. For information on using the i.LINK Control Panel, see page 89. Also available in the Applications Menu (page
108). Press repeatedly to cycle through the video equipment connected to the TV's video inputs. Press to switch between the sources connected to the TV's
VHF/UHF and CABLE inputs. Use with 0-9 and ENTER buttons to select digital channels (for example, 2.1). For details on selecting digital channels, see
page 54.
Press to display the Scrolling Index. For details, see page 57. Press repeatedly to step through the Screen Mode settings. Also available in the Screen Menu.
For details, see pages 58 and 99. Press to display the Menu. Press again to exit from the Menu. For details, see page 93. Press to adjust the volume. Move the
joystick V v B b to move the on-screen cursor.
To select an item, press the center of the joystick ( ). Press repeatedly to cycle through the available highresolution picture modes: Interlaced, Progressive,
CineMotion. Also available in the Video Menu. For details, see "Selecting Video Options" on pages 94-95. Press to reset the settings to the factory defaults.
See pages 96 and 98. Also used to clear Favorite Channels (see page 63). Press to display the Favorite Channels list. For details, see page 63. 2 SLEEP i.
LINK TV/VIDEO FUNCTION SAT/CABLE TV ANT PIC MODE qj qk SETUP 4 5 ql 3 i.LINK ENTER Remote Control 6 7 SCREEN MODE FLIP OPEN
INDEX TWIN VI EW 8 9 VOL MENU CH w; 4 TV/VIDEO 5 ANT q; ME MODE M ORY STIC K wa 6 qa qs qd qf qg ws PALETTE wd RESET DRC
FAVORITES GUIDE CODE SET FREEZE EXIT JUMP DISPLAY 7 INDEX 8 SCREEN MODE wf wg wh wj wk SETUP TV RM-Y201 9 MENU q; VOL +/qa
SETUP qs DRC MODE qd RESET SETUP qf FAVORITES 48 Button Description qg CODE SET Press to program the remote control to operate nonSony
video equipment. For details, see "Programming the Remote Control" on page 51. SAT/CABLE: Press to turn on and off the satellite receiver or cable box.
TV: Press to turn on and off the TV. The indicator lights up momentarily when pressed to show which equipment the remote control is operating:
SAT/CABLE: Press to have the remote control operate the satellite receiver or cable box. TV: Press to have the remote control operate the TV. SETUP qh
POWER Buttons qj FUNCTION Buttons SETUP qk PIC MODE Press repeatedly to cycle through the available video picture modes: Vivid, Standard, Movie,
Pro. Also available in the Video Menu. For details, see "Selecting Video Options" on page 94.
Press 0 - 9 to select a channel; the channel changes after 3 seconds. Press ENTER to change channels immediately. Press to turn on and off Twin View. For
details, see pages 60-62. Press to scan through channels. To scan quickly through channels, press and hold down either CH button. Remote Control ql 0 - 9
ENTER w; TWIN VIEW wa CH +/- ws MEMORY STICK Press to display the Memory Stick Menu. For details, see "Using the Memory Stick Viewer" on page
69. Also available in the Applications Menu (page 108). wd DRC PALETTE Press repeatedly to cycle through the three Custom DRC Palette options.
Also available in the Video Menu. For details, see "Selecting Video Options" on pages 94-96. Press once to display the current channel number, current time,
and program information banner. Press again to turn Display off. Press to display the program guide.
For details, see page 55. Press to jump back and forth between two channels. The TV alternates between the current channel and the last channel that was
selected. Press to exit the on-screen Menu or display and return to normal viewing. Press to freeze the window picture.
Press again to restore the picture. For details see page 65. SETUP wf DISPLAY SETUP wg GUIDE wh JUMP wj EXIT wk FREEZE SETUP 49 Inside Panel
To access the inside panel, open the outside cover as shown. SETUP Opening the outside cover automatically switches the remote control to operate your
VCR or DVD player, depending on the position of the A/V slide switch. For details, see page 51. VCR and DVD buttons require that you first program the
remote (page 51), if the VCR and DVD player are not Sony brand. MUTING SLEEP SAT/CABLE POWER SAT/CABLE FUNCTION TV TV/VIDEO ANT PIC
MODE Button Description SETUP wg SYSTEM OFF MP ENTER SCREEN MODE INDEX TWIN VIEW MENU VOL CH wh Transport Buttons ME MODE
MORY STICK PALETTE RESET DRC FAVORITES GUIDE DISPLAY CODE SET FREEZE EXIT JUMP Remote Control TV RM-Y201 wj MTS/SAP wk V v B
b MUTING SLEEP SAT/CABLE POWER SETUP TV/VCR/DVD VCR/DVD wg wh wj wk wl SYSTEM OFF i.LINK e; ea es wl DISC MENU e; TV/VCR/DVD
ea VCR/DVD es i.LINK AV1/2/3/DVD Slide Switch Press to turn off all Sony brand audio/video equipment at once. (May not function with older Sony
equipment.
) m Rewind N Play z Record (press together with N) To record with i.LINK devices, press only z. x Stop M Fast forward X Pause Press repeatedly to cycle
through the Multi-channel TV Sound (MTS) options: Stereo, Auto SAP (Second Audio Program), and Mono. Also available in the Audio Menu. For details,
see "Using the Audio Menu" on page 97. Press Vv B b to move the VCR or DVD player's onscreen cursor. Press to display the DVD Menu. Press to change to
the VHF/UHF output of the VCR (or DVD/VCR combination unit). Press to turn on and off the VCR or DVD player. Use the A/V slide switch to control
connected video or i.
LINK equipment. You can program one video source for each switch position. i.LINK-connected devices are by default set to AV1. For details, see
"Programming the Remote Control" on page 51.
Press repeatedly to step through the Audio Effect options. Also available in the Audio Menu. For details, see page 97. Press to select an item in the VCR or
DVD player's Menu. Press to display the DVD player setup Menu.
MTS/SAP SELECT ed ef MENU DISC MENU eg ed SETUP SC ODE REEN M INDEX TWIN VI EW ef SELECT eg MENU SETUP 50 Programming the
Remote Control The remote control is preset to operate Sony brand video equipment. SETUP Sony Equipment Switch Position on Remote Control
Programmable Code Number i.LINK 8 mm VCR MUTING SLEEP SAT/CABLE POWER i.LINK/AV1 AV2 AV3 DVD 901 302 301 751 VHS VCR DVD player
TV/VCR/DVD VCR/DVD SYSTEM OFF i.LINK 2 MTS/SAP If you have video equipment other than Sony brand that you want to control with the TV's remote
control, use the following procedure to program the remote control. SETUP SELECT The equipment must have infrared (IR) remote capability in order to be
used with the remote control. MENU DISC MENU Remote Control 1 Turn to the list of "Manufacturer's Codes" on page 52, and find SCREEN MODE INDEX
TWIN VI EW the three-digit code number for the manufacturer of your equipment.
You're reading an excerpt. Click here to read official SONY
KD-34XBR960 user guide
http://yourpdfguides.com/dref/267302
Powered by TCPDF (www.tcpdf.org)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising