cover PG1500

cover PG1500
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
CLICK-N-GO AUTO CARRIER
PG1500
ets
For Pnly
O
To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
customerservice@petgearinc.com
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig,
chew or paw aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage
caused by aggressive, destructive, immature or untrained animals. Do not use near an open or exposed
flame. Failure to follow these warnings and the instructions could result in serious injury or death.
PARTS LIST
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service. No tools required.
(1) Top
(1) Bottom
(1) Bowl
(1) Rod
(1) Seat Belt Clip
(1) Click ‘N Go Base
(1) Door
(4) Wing Nuts
2
CLICK ‘N GO Auto Carrier PG1500
ASSEMBLY
Wing Nut
Step 1. Place top on bottom and secure
with two wing nuts in back holes
(Figure 1).
Figure 1
DO NOT INSTALL THE TWO FRONT
WING NUTS UNTIL THE FRONT DOOR IS
INSTALLED. DO NOT OVER-TIGHTEN!
Wing Nut
Flange
Step 2. Snap on bowl, then install metal rod
through food/water tray. Make sure flange is
at the top. (Figure 2)
Figure 2
Snap
On
Bowl
Step 3. Lay crate on its side, secure with one wing
nut, then insert metal rod (with door attached) into
holes. (Figure 3)
Figure 3
CLICK ‘N GO Auto Carrier PG1500
3
ASSEMBLY
Figure 4
Step 4. Insert final wing nut. (Figure 4)
Wing Nut
TO INSTALL BASE
WARNING: IF BASE IS IN FRONT
SEAT, SHUT OFF AIR BAG.
Figure 5
Step 1. Place seat belt through seat as shown and
insert latch plate into buckle until you hear a click.
(Figure 5)
Step 2. Pull on shoulder strap to tighten base and
thread it back through the base.
(Figure 6 and Figure 7.)
Figure 6
NOTE: BASE WAS MADE WITH AN
ANGLE TO CONFORM TO
YOUR CAR SEAT.
Figure 7
4
CLICK ‘N GO Auto Carrier PG1500
TO INSTALL BASE
Attach metal clip over both belts as shown in
Figure 8, 9 and 10.
Pull on base to make sure it is secure.
The vehicle lap belt must be tight around the
base and must stay tight.
If base cannot be held tightly, check owner’s
manual, see “Vehicle Seat Belt” section
or move it to another seating location. If there
is not a location that will keep the base secure
with the lap belt, contact your vehicle dealer
to have a lap belt installed in your vehicle.
Figure 8
Figure 9
Figure 10
Handle
Place carrier on base. (Figure 11)
Pull up on handle to make sure carrier
is secure. To release, depress lever
and pick up on handle.
To remove locking clip
1. Unbuckle seat belt.
2. Pinch sides of seat belt together
and remove metal clip.
CLICK ‘N GO Auto Carrier PG1500
Lever
Figure 11
5
REPLACEMENT PARTS
Please have your model number ready before calling. Use only PET GEAR replacement parts.
PO Box 99
West Rutland, VT 05777
877-752-9123
www.petgearinc.com
6
ets
For P o
Up T
s
15 lb
CLICK ‘N GO Auto Carrier PG1500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising