Scion tC instructions
Doc. 19.99.00
Business Partner: L95
TOYOTA
PIO / DIO
11/24/14
Scion TC 2015
XM Satellite Radio
Part Number:00016-00950
Accessory Code: RX1000
Conflicts
Vehicle Service Parts (May be required for reassembly)
1. Vehicles with BeSpoke Radio.
2. Vehicles without touch-screen radio.
Kit Contents
Item #
Qty
1
1
XM Module
Description
2
1
XM Tuner Module
3
1
Wiring Harness
4
1
Hardware Bag
5
1
XM Antenna
6
2
24” Wire Ties
Part Number
Qty
Description
00016-00950-01
1
Main Wiring Harness
00016-00950-02
1
Pairing Button
00016-00950-03
1
XM Antenna
00016-00950-04
1
XM Tuner Module
00016-00950-05
1
Hardware Bag
00016-00950-06
1
Interface Control Module
General Applicability
1. Radios without factory XM
Legend
STOP
Hardware Bag Contents
Item #
Qty Reqd.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
Description
1
24
8” Black Cable Ties
2
2
Red T-Taps
3
2
Blue T-Taps
4
2
Black T-Taps
5
1
2” x 2” Foam Mounting Pad
6
1
3.5” x 6” Foam Pad
7
6
1 1/4” x 2 1/2” Foam Pad
8
2
1” x 1” Double Side Mounting Tape
9
4
1/2” Philips Screws
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
!
CRITICAL PROCESS: Proceed with caution to
ensure a quality installation. These points will be
audited on a completed vehicle installation.
TOOLS AND EQUIPMENT: This calls out the specific tools and equipment required for this process.
REVISION MARK: This mark highlights a change in
installation with respect to a previous issue.
S
SAFETY TORQUE: This mark indicates that torque
is related to safety.
Recommended Tools
Safety Tools
Special Tools
Installation Tools
Phillips Screwdriver
Straight-Slot Screwdriver
Ratchet w/ Extension
10 mm Socket
Diagonal Wire Cutters
Common Pliers
Flashlight
Nylon Trim Tool
Torque Wrench (48 in. lbs.)
Electrical Tape
Protective Tape
1/8” Drill Bit
Power Drill
SPECIAL NOTE:
After TMS and Safety mandated preparatory steps have
been taken, the installation sequence is the suggested
method for completing the accessory installation. In some
instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a
team accessory installation. Unless otherwise stated in the
document, the associates may perform the installation steps
in any order to make the installation as efficient as possible
while maintaining consistent quality.
DIAGNOSTIC NOTE:
Diagnostic and troubleshooting information on this
accessory is available on SET Dealer Daily. Please
visit the service information section of SET Dealer
Daily for more information.
Special Chemicals
VDC Approved Cleaner
VDC Approved Sealant
Rev. Southeast Toyota Distributors, LLC
11/21/2014
INSTALLATION PREPARATION
SCION TC 2015
Negative Battery
Cable
Before starting installation:
1. Familiarize yourself with the installation
instructions.
2. Inspect the kit components (Refer to Kit
Contents and Hardware Bag Contents).
Left Hand Pictured
VEHICLE PREPARATION
1. Place protective coverings on vehicle.
! 2. “IMPORTANT......IMPORTANT”
Disconnect Negative Battery Cable.
3. Using a nylon trim tool, disengage 5 clips
and 1 claw and remove radio bezel.
4. Remove 4 bolts, disconnect electrical connectors and remove radio from vehicle.
Southeast Toyota Distributors, LLC
XM Satellite Radio
Page 2 of 15
SCION TC 2015
VEHICLE PREPARATION; continued
5. Disengage the 12 claws, and remove RH
front door scuff plate.
6. Disengage 2 clips and 1 claw, and remove
RH cowl side trim board.
7.Flex the glove compartment door stoppers
inward slightly to release them from the
dash bracing. Fold glove compartment
door downward and remove from vehicle.
Southeast Toyota Distributors, LLC
Page 3 of 15
XM Satellite Radio
VEHICLE PREPARATION; continued
SCION TC 2015
8. Disengage the 5 claws and remove the
lower instrument panel cover behind the
glove compartment.
Southeast Toyota Distributors, LLC
Page 4 of 15
XM Satellite Radio
SCION TC 2015
INSTALLATION PROCEDURES
1. Clean antenna base and antenna mounting location with VDC approved cleaner.
2. Attach supplied double sided mounting
tape onto the antenna base and mount
the XM antenna to the passenger front
corner of roof, as shown.
3.Tuck XM antenna cable into roof glass
weather strip with a nylon trim tool as
shown.
4.Tuck XM antenna cable between rubber
windshield seal and vehicle body with a
nylon trim tool, and route XM antenna
cable to bottom of windshield inside the
cavity behind the seal.
Southeast Toyota Distributors, LLC
Page 5 of 15
XM Satellite Radio
INSTALLATION PROCEDURES; continued
SCION TC 2015
XM Satellite Radio
5. Lift cowl trim at base of windshield and
route XM antenna cable under the trim.
Wire Tie here
6. Secure XM antenna cable away from
hood hinge with 1 wire tie and 1 foam pad
as pictured.
Southeast Toyota Distributors, LLC
Page 6 of 15
Foam Pad
SCION TC 2015
INSTALLATION PROCEDURES; continued
7. Route the XM antenna cable along factory
harness. Use wire ties to secure cable to
factory harness as shown.
Wire Ties
8. Locate nipple in main harness grommet
under hood. Using a pair of cutters, cut
end off nipple.
9. Locate grommet inside vehicle behind
glove compartment. Pull antenna cable
through grommet.
NOTE: LUBRICATE ANTENNA CABLE
WITH SOAP/WATER BEFORE PULLING
ANTENNA CABLE THROUGH VEHICLE
GROMMET TO PREVENT DAMAGE TO
ANTENNA CONNECTOR.
Southeast Toyota Distributors, LLC
Page 7 of 15
XM Satellite Radio
INSTALLATION PROCEDURE; continued
SCION TC 2015
XM Satellite Radio
10. Seal open grommet with VDC approved
sealant.
11. Secure any excess antenna wire to the factory wiring harness above the passenger’s
kick panel.
Module Mounting Location
12. Route the RED and YELLOW power wires
behind glove compartment brace towards
radio mounting location. Secure the harness
to brace with wire ties, as pictured.
13. Route the BLACK ground wire to the factory
ground lug in the passenger’s kick panel.
Secure with wire ties, as necessary.
Southeast Toyota Distributors, LLC
Page 8 of 15
Wire Ties
Factory Ground Lug
SCION TC 2015
XM Satellite Radio
INSTALLATION
14. Apply the supplied piece of 1x1 double
sided tape to the bottom side of the pairing button.
15. Using a 1/8” drill bit, pre drill holes in the
mounting slots. Then use the supplied
screws to secure the pairing button to the
glove compartment upper trim panel.
16. Secure the pairing button’s harness to the
rear of the glove compartment trim panel
with a foam pad.
17. Connect the main power harness, pairing
button harness, and the mini-tuner to the
interface module. Attach the XM minituner to the interface module using the
supplied
2 1/4” x 2 1/4” adhesive pad.
Adhesive Pad
18. Wrap the module with the supplied large
foam pad, ensuring that the connector
ports are left accessible.
19. Secure the XM interface adapter, XM
module and any excess harness to the
factory harness above the passenger’s
kick panel with (2) long wire ties.
NOTE: DO NOT SECURE THE MODULE
STOP OR ANY WIRING TO THE YELLOW AIRBAG HARNESS.
Southeast Toyota Distributors, LLC
Page 9 of 15
Module Mounting Location
SCION TC 2015
XM Satellite Radio
INSTALLATION
20. Locate the factory ground point C2.
21. Secure the BLACK ground wire to the
factory ground lug.
22. Using a blue T-Tap, connect the RED
power wire to the BLUE wire of connector
C1, PIN 4.
23. Using a red T-Tap, connect the YELLOW
ACC wire to the YELLOW wire of connector C1, PIN 3.
Connector C1
Located behind
factory radio.
Yellow
Location 3
Accessory
(5A ACC Fuse)
24. Secure the radio to the dash assembly using the (4) 10 mm bolts previously
removed.
25. Temporarily reconnect the negative battery cable.
Southeast Toyota Distributors, LLC
Page 10 of 15
Blue
Location 4
+12VDC
(15A RAD1 Fuse)
SCION TC 2015
PAIRING THE DEVICE:
XM Satellite Radio
Source
Bluetooth Audio
1. Access the Bluetooth® Streaming Audio source
in the vehicle's radio.
Select to
Connect
Device
Audio player is not connected
Connect
2. Press the "Connect" button to display the
paired device list.
Source
Connect Audio Player
Select "Yes" to
Add Device
3. Select the “Yes" button to add the new device.
At this point the radio will enter discoverable
mode, allowing the Streaming Bluetooth®
Satellite Radio device to connect.
There are no audio players registered.
Would you like to add one now?
Yes
4. Locate the pairing button for the Bluetooth®
Satellite Radio Device in the vehicle's glove
compartment.
No
Connect Bluetooth
Registration Waiting
Please operate the device to register it.
Device Name : CAR MULTIMEDIA
Device Address : 1C994C838B782
Passcode
: 0000
1. PRESS and HOLD the pairing button for
about 3 seconds. The Status Indicator
LED will start flashing RED quickly,
indicating the pairing procedure has
started.
Cancel
Status Indicator LED
Pairing Button
2. Release the button when it starts to flash
RED quickly.
3. The LED will start to flash GREEN quickly,
indicating that it is connecting with the
radio.
4. Finally, the LED will begin to slowly flash
GREEN to indicate that it has successfully
paired to the vehicle's radio.
Select
SiriusXM
Connect Audio Player
SiriusXM
Add New
5. "SiriusXM" will now display on the paired
device list. Select the SiriusXM icon to select the
device.
Southeast Toyota Distributors, LLC
Page 11 of 15
SCION TC 2015
XM Satellite Radio
VEHICLE RE-ASSEMBLY
1. Disconnect the negative battery terminal.
Negative Battery
Cable
2. Refer again to the vehicle repair manual and re-assemble
all panels that were removed for installation.
S
2. Re-connect the negative battery cable. Torque to 48 in. lbs.
TESTING THE RADIO
1. Prior to delivering the vehicle, test all features of the factory system according to the vehicle’s
owner’s manual.
2. Making sure that the vehicle is outside where the XM Antenna has a clear view of the sky, verify
that the radio is able to receive channel 0 (Radio ID Number) and channel 1 (Preview Channel).
You should be able to hear audio through the Preview Channel, as well as view the text data displaying on the screen.
3. Check steering wheel mounted audio control functionality (if equipped).
Model
VOL +
VOL -
^
v
TC
Volume UP
Volume DOWN
Channel UP
Channel DOWN
4. Place owner’s manual in the glove compartment.
Southeast Toyota Distributors, LLC
Page 12 of 15
SCION TC 2015
XM Satellite Radio
VEHICLE FUNCTION CHECKLIST
(These points must be checked to ensure a quality installation)
Headlight
If the warning lights remains on, it may indicate
a system malfunction.
Massage Seats (if equipped)
High Beams
Side Mirror Defogger (if equipped)
Turn Signal Lights
Front Windshield Defogger (if equipped)
Tail Lights
Navigation System (if equipped)
Stop Lights
Rear Sunshade (if equipped)
Backup Lights
Cruise Control Light (if equipped)
Hazard Lights
Steering Wheel Audio Control (if equipped)
Marker Lights
HVAC
Dome/Courtesy Lights
Power Locks (if equipped)
Panel/Switch Illumination
Power Windows (if equipped)
Accessory Controls/Illumination
(If equipped)
Gauges
Front Wiper/washer
Rear Window Defogger (If equipped)
Hood Latch Release
Key Sensor Buzzer
Passenger Air Bag Switch (if equipped)
Fog Lights (If equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
Day Time Running Lights
(If equipped)
Horn
Seat Belt Warning Light
If the warning lights remains on, it may indicate
a system malfunction.
Trunk/Tailgate/Bed Lights
(If equipped)
Glove Box Light (If equipped)
Air Bag Warning Light
If the warning lights remains on, it may indicate
a system malfunction.
ABS Light (If equipped)
Rear Wiper/Washer (If equipped)
Lamp Failure Sensor
If the warning lights remains on, it may indicate
a system malfunction.
Clock (If equipped)
Accessory Power Socket (If equipped)
Track/Skid Control Light (if equipped)
If the warning lights remains on, it may indicate
a system malfunction.
Starter
Audio/Video (If equipped)
Power Rear Door (If equipped)
Convenience Memory Settings (If equipped)
Heated Seats (If equipped)
Southeast Toyota Distributors, LLC
Power Side Mirrors (if equipped)
Page 13 of 15
Tire Pressure Monitoring System (TPMS)
Prior to TPMS activation and Pre-Delivery
Service (PDS) of the vehicle the TPMS light will
blink when IG is turned on.
SCION TC 2015
Block Diagram
SatStream Radio:
Kit P/N 00016-00950
Idle current draw - 4 mA
Connects to
+12VDC Accessory Circuit
Connects to
Constant +12VDC
Battery Circuit.
2A
R
Y
SiriusXM
Antenna
R
Y
Pairing
Button
C-1
C-1
1
ACCY
B+
SatStream Control
Module
GND
2
B
C-1
Connects to
Chassis Ground
Location.
Southeast Toyota Distributors, LLC
3
Page 14 of 15
ANT
Shielded
Cable
SiriusXM Tuner
Module
XM Satellite Radio
SCION TC 2015
XM Satellite Radio
Checking the Harness Pinouts:
Connector C-1:
Main Harness Connector
Terminal View
1
2
3
4
Unplug the 4 pin connector from the module, and perform all tests at the terminal side of the
connector. If feedback from the vehicle on any of the Pins does not match the results shown in
the Proper Operation field, then the module is not receiving the correct signals from the vehicle.
Check the connection to the vehicle wiring then re-test.
Pin
Wire Color
Test Reference
Proper Operation
1
Red
Pin 1 to Ground.
 Always +12 VDC.
2
Yellow
Pin 2 to Ground.
 +12 VDC with ignition on.
 0 VDC with ignition off.
3
Black
Pin 3 to Ground.
 Always shows continuity.
4
No Connection
T-TAP INSTALLATION
When installing female T-Tap connectors, be sure the wire is located inside the wire channel of the female T-Tap connector before closing the connector over the wire with pliers. When possible, install T-Taps at least 1" from connector.
Step A
Step B
Step C
Wire from
main harness
T-Tap
IMPORTANT! After installation, inspect and ensure that Keyless System Harnesses are clear of
all HOT, SHARP or MOVING objects.
IMPORTANT! Care MUST be exercised when using the BLACK T-Taps. To avoid damage and
broken wires, please note:
• Ensure there is NO tension on the T-Tap connection when securing the harness. The wire
should be slack.
• Excessive manipulation and/or stress on the wire connection could lead to wire breakage.
• Center the wire in the metal insert, NOT the plastic side of the T-Tap. Misalignment of the
wire against the metal insert could lead to cutting the wire.
• It is recommended to close close the T-Tap with your fingers (Step A above). After the
T-Tap has been closed with your fingers, applying light pressure with a set of pliers will
Southeast Toyota Distributors, LLC
Page 15 of 15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising